LG | ABNH12GL2A2.ENWAATK | Owner's Manual | LG ABNH12GL2A2.ENWAATK Owner's Manual

LG ABNH12GL2A2.ENWAATK Owner's Manual
ENGLISH
TÜRKÇE
INSTALLATION MANUAL
AIR
CONDITIONER
Please read this installation manual completely before installing the product.
Installation work must be performed in accordance with the national wiring
standards by authorized personnel only.
Please retain this installation manual for future reference after reading it
thoroughly.
Ceiling Concealed Duct – Low static
Original instruction
www.lg.com
P/NO : MFL67855525
Single A Air Conditioner Installation Manual
CONTENTS
Safety Precautions ..............................................................................................3
Installation Parts..................................................................................................6
Installation............................................................................................................7
Remote Controller Installation .........................................................................15
Optional Operation ............................................................................................19
How to Set E.S.P?..............................................................................................26
Self-diagnosis Function ....................................................................................28
Dip Switch Setting .............................................................................................28
2
Safety Precautions
This symbol indicates the possibility of death or serious injury.
This symbol indicates the possibility of injury or damage to properties only.
n The meanings of the symbols used in this manual are as shown below.
Be sure not to do.
Be sure to follow the instruction.
n Installation
Always perform grounding.
• Otherwise, it may cause electrical shock.
Securely attach the electrical
part cover to the indoor unit
and the service panel to the
outdoor unit.
Don’t use a power cord, a
plug or a loose socket which
is damaged.
• Otherwise, it may cause a fire or • Otherwise, it may cause a fire,
electrical shock, explosion or inelectrical shock.
jury.
Always install an air leakage
breaker and a dedicated
switching board.
• If the electrical part cover of the • No installation may cause a fire
indoor unit and the service panel and electrical shock.
of the outdoor unit are not attached securely, it could result in
a fire or electric shock due to
dust, water, etc.
Ensure that an installation frame of the outdoor unit is not damaged due to use for a long
time.
• It may cause injury or an accident.
For installation of the product,
always contact the service center or a professional installation
agency.
Do not keep or use flammable
gases or combustibles near
the air conditioner.
• Otherwise, it may cause a fire or
the failure of product.
Do not disassemble or repair the product randomly.
• It will cause a fire or electrical shock.
Installation Manual 3
ENGLISH
Safety Precautions
To prevent the injury of the user or other people and property damage, the following instructions
must be followed.
n Be sure to read before installing the air conditioner.
n Be sure to observe the cautions specified here as they include important items related to safety.
n Incorrect operation due to ignoring instruction will cause harm or damage. The seriousness is
classified by the following indications.
Safety Precautions
Do not install the product at a place that there
is concern of falling down.
• Otherwise, it may result in personal injury.
Use caution when unpacking and installing.
• Sharp edges may cause injury.
n Operation
Do not share the outlet with
other appliances.
• It will cause an electric shock
or a fire due to heat generation.
Do not use the damaged
power cord.
• Otherwise, it may cause a fire
or electrical shock.
Do not modify or extend the
power cord randomly.
• Otherwise, it may cause a fire
or electrical shock.
Take care so that the power
cord may not be pulled during operation.
Unplug the unit if strange
sounds, smell, or smoke
comes from it.
• Otherwise, it may cause a fire
or electrical shock.
• Otherwise, it may cause electrical shock or a fire.
• Otherwise, it may cause a fire.
Do not use the power cord
near the heating tools.
Do not open the suction
inlet of the indoor/outdoor
unit during operation.
Take the power plug out if
necessary, holding the head
of the plug and do not touch
it with wet hands.
• Otherwise, it may cause a fire
or electrical shock.
Do not allow water to run
into electrical parts.
• Otherwise, it may cause the
failure of machine or electrical
shock.
• Otherwise, it may cause a fire
and electrical shock.
Hold the plug by the head
when taking it out.
• It may cause electric shock
and damage.
Do not step on the indoor/outdoor unit and
do not put anything on it.
• It may cause an injury through dropping of the
unit or falling down.
When the product is submerged into water,
always contact the service center.
• Otherwise, it may cause a fire or electrical
shock.
4
Keep the flames away.
• Otherwise, it may electrical
shock and failure.
Never touch the metal parts
of the unit when removing
the filter.
• They are sharp and may
cause injury.
Do not place a heavy object on the power
cord.
• Otherwise, it may cause a fire or electrical
shock.
Take care so that children may not step on
the outdoor unit.
• Otherwise, children may be seriously injured
due to falling down.
Safety Precautions
ENGLISH
n Installation
Install the drain hose to ensure that drain
can be securely done.
• Otherwise, it may cause water leakage.
Always inspect gas leakage after the installation and repair of product.
• Otherwise, it may cause the failure of product.
Install the product so that the noise or hot
wind from the outdoor unit may not cause
any damage to the neighbors.
• Otherwise, it may cause dispute with the neighbors.
Keep level parallel in installing the product.
• Otherwise, it may cause vibration or water leakage.
n Operation
Avoid excessive cooling and perform ventilation sometimes.
• Otherwise, it may do harm to your health.
Do not use an appliance for special purposes
such as preserving animals vegetables, precision machine, or art articles.
• Otherwise, it may damage your properties.
Use a soft cloth to clean. Do not use wax,
thinner, or a strong detergent.
• The appearance of the air conditioner may deteriorate, change color, or develop surface
flaws.
Do not place obstacles around the flow inlet
or outlet.
• Otherwise, it may cause the failure of appliance
or an accident.
Installation Manual 5
Installation Parts
Installation Parts
Air outlet vents
Air filters
Air intake vents
Control box
Wired Remote Controller
Name
Drain hose
Quantity
1 EA
Washer for
Clamp metal hanging bracket
2 EA
8 EA
Clamp
(Tie Wrap)
Insulation for
fitting
4 EA
1 set
Other
• Owner's manual
• Installation manual
Shape
for gas pipe
for liquid pipe
• Screws for fixing panels are attached to decoration panel.
6
Installation
ENGLISH
Installation
Selection of the best location
Indoor unit
Top view (Unit: mm) Inspection hole
Install the air conditioner in the location that satisfies the following conditions.
• The place shall easily bear a load exceeding
four times the indoor unit’s weight.
• The place shall be able to inspect the unit as
the figure.
• The place where the unit shall be leveled.
• The place shall easily connect with the outdoor
unit.
• The place where the unit is not affected by an
electrical noise.
• The place where air circulation in the room will
be good .
• There should not be any heat source or steam
near the unit
Confirm the positional relationship between the
unit and suspension bolts.
• Installation the ceiling opening to clean the filter or service under the product.
Control box
(600 x 600)
600
Air outlet
600
Side view (unit: mm)
Air outlet
H=20 or more
• Suitable dimension "H" is necessary to get a slope
to drain as shown in the figure
(Unit: mm)
Capacity (kBtu/h)
A
B
9
800
800
12/18
800
1000
24
800
1200
A(Min)
B(Min)
Ceiling
Service Space
A
B
Installation Manual 7
Installation
Ceiling dimension and hanging bolt location
Installation of Unit
Install the unit above the ceiling correctly.
E
G
POSITION OF SUSPENSION BOLT
• Apply a joint-canvas between the unit and duct
to absorb unnecessary vibration.
• Apply a filter Accessory at air return hole.
D C
J
A
B
(Unit: mm)
C
D
E
F
G
H
I
J
9
733 772 628 700 36 190 20 660 155 700
12/18
933 972 628 700 36 190 20 860 155 900
24
1133 1172 628 700 36 190 20 1060 155 1100
I
B
F
Dimension
Capacity
A
(kBtu/h)
H
Drainage hole
※ Install the unit leaning to a drainage hole side
as a figure for easy water drainage.
POSITION OF CONSOLE BOLT
• A place where the unit will be leveled and that
can support the weight of the unit.
• A place where the unit can withstand its vibration.
• A place where service can be easily performed.
8
M10 Nut
X4
M10 washer
X4
M10 washer
X4
M10 Nut
X8
Installation
• Select and mark the position for fixing bolts.
• Drill the hole for set anchor on the face of ceiling.
• Insert the set anchor and washer onto the suspension bolts for locking the suspension bolts
on the ceiling.
• Mount the suspension bolts to the set anchor
firmly.
• Secure the installation plates onto the suspension bolts (adjust level roughly) using nuts,
washers and spring washers.
Old building
New building
1 Set anchor
2 Plate washer
3 Spring washer
4 Nut
CAUTION : Tighten the nut and bolt to
prevent unit falling.
5 Suspension
bolts
Wiring Connection
Connect the wires to the terminals on the control board individually according to the outdoor unit
connection.
• Ensure that the color of the wires of outdoor unit and the terminal No. are the same as those of indoor unit respectively.
L1/L2/L3 Series
Indoor unit
Outdoor unit
Terminal Block Indoor
1(L)
2(N)
Terminal Block Indoor
3
Terminal Block outdoor
1(L)
2(N)
3
WARNING : Make sure that the screws of the terminal are free from looseness.
CAUTION : The Power cord connected to the unit should be selected according to the
following specifications. (Cable type CV approved by IEC 60502-1)
NORMAL
CROSS-SECTIONAL
AREA 2.5mm2
GN
/YL
20
mm
Installation Manual 9
ENGLISH
Indoor Unit Installation
Installation
CAUTION :
After the confirmation of the above conditions, prepare the wiring as follows:
1) Never fail to have an individual power specialized for the air conditioner.
As for the method of wiring, be guided by the circuit diagram posted on the
inside of control box cover.
2) Provide a circuit breaker switch between power source and the unit.
3) The screws which fasten the wiring in the casing of electrical fittings are liable to come loose from vibrations to which the unit is subjected during the
course of transportation. Check them and make sure that they are all tightly
fastened. (If they are loose, it could give rise to burn-out of the wires.)
4) Specification of power source
5) Confirm that electrical capacity is sufficient.
6) Be sure that the starting voltage is maintained at more than 90 percent of the
rated voltage marked on the name plate.
7) Confirm that the cable thickness is as specified in the power sources specification. (Particularly note the relation between cable length and thickness.)
8) Never fail to equip a leakage breaker where it is wet or moist.
9) The following troubles would be caused by voltage drop-down.
• Vibration of a magnetic switch, damage on the contact point, fuse breaking, disturbance by the normal function of an overload protection device.
• Proper starting power is not given to the compressor.
10
Installation
ENGLISH
Part name and functions
• Low static duct type in case of suction from
back side.
Air Filter
Air outlet
Panel Rear
• Low static duct type in case of suction from
bottom side.
Panel Rear
Air outlet
Air Filter
• In case of suction from bottom size, bend the
Panel rear and screw with cabinet case
Cabinet case
Panel Rear
Installation Manual 11
Installation
INSULATION, OTHERS
THERMAL INSULATION
Insulate the joint and tubes completely.
All thermal insulation must comply with local requirement.
INDOOR UNIT
Union for gas pipe
Thermal insulator for refrigerant pipe
(Local supply) Thermal insulator for
piping(Local supply)
Refrigerant pipe and thermal
insulator(Local supply)
Hose clip for thermal insulator
(Local supply)
Thermal insulator for refrigerant pipe
(Local supply)
Union for liquid pipe
Overlap with thermal
insulator for piping.
Hose clip for thermal insulator(Local supply)
Make sure that there is no clearance here.
Felt
Cabinet
Insulation
No clearance
TEST AND CHECK
n After all workings are finished, check the working and operation.
• Air distribution ............... Is the air circulation good?
• Drain ............................. Is the drainage smoothly and no sweating?
• Gas leakage ................. Is the piping connection correctly?
• Wiring ........................... Is the wiring connection correctly?
• Lock-bolt ....................... Is the lock-bolt of compressor loosened?
• Insulation....................... Is the unit fully insulated?
• Ground .......................... Is the unit safely grounded?
Checking the Drainage
1. Remove the Air Filter.
2. Check the drainage.
• Spray one or two glasses of water
upon the evaporator.
• Ensure that water flows drain hose of indoor unit without any leakage.
12
Installation
1. Install declination of the indoor unit is very important for the drain of the duct type air conditioner.
2. Minimum thickness of the insulation for the connecting pipe shall be 19mm.
Front of view
• The unit must be horizontal or declined to the drain hose connected when finished installation.
Ceiling
Drainage hole
Drain Pump use
Part name and functions
• Drain piping must have down-slope (1/50
to 1/100): be sure not to provide up-anddown slope to prevent reversal flow.
• During drain piping connection, be careful
not to exert extra force on the drain port
on the indoor unit.
• The outside diameter of the drain connection on the indoor unit is 32mm.
Pipe clamp
Indoor unit
Upward
routing
not allowed
Maintenance
drain port
Piping material: Polyvinyl chloride pipe VP-25
and pipe fittings
• Be sure to install heat insulation on the
drain piping.
Heat insulation material: Polyethylene foam
with thickness more than 8 mm.
Drain test
The air conditioner uses a drain pump to drain water.
Use the following procedure to test the drain pump operation:
Feed water
Flexible drain hose
Main
drain pipe
Drain Pump
Drain
port
Glue the joint
Drain hose connection
Use the clip
Drain pan
• Connect the main drain pipe to the exterior and leave
it provisionally until the test comes to an end.
• Feed water to the flexible drain hose and check the
piping for leakage.
• Be sure to check the drain pump for normal operating and noise when electrical wiring is complete.
• When the test is complete, connect the flexible drain
hose to the drain port on the indoor unit.
Installation Manual 13
ENGLISH
CAUTION
Installation
Max 300mm
Hanger
distance
1~15m
Metal
clamp
Flexible drain hose
Hanger Bracket
1/50~1/100 slope
Max 700mm
CAUTION : The supplied flexible drain
hose should not be curved, neither
screwed. The curved or screwed hose
may cause a leakage of water.
Insulation
HAND OVER
Teach the customer the operation and maintenance procedures, using the operation manual.
(air filter cleaning, temperature control, etc.)
14
Remote controller installation
ENGLISH
Remote controller installation
WIERED REMOTE CONTROLLER INSTALLATION
• Since the room temperature sensor is in the remote controller, the remote controller box should be installed in a place away from direct sunlight, high humidity and direct supply of cold air to maintain proper
space temperature. Install the remote controller about 5ft(1.5m) above the floor in an area with good air
circulation at an average temperature.
Do not install the remote controller where it can be affected by:
- Drafts, or dead spots behind doors and in corners.
- Hot or cold air from ducts.
- Radiant heat from sun or appliances.
- Concealed pipes and chimneys.
- Uncontrolled areas such as an outside wall behind the remote controller.
- This remote controller is equipped with a seven segment LED. display. For proper display of the remote
controller LED's, the remote controller should be installed properly as shown in Fig.1.
(The standard height is 1.2~1.5 m from floor level.)
yes
no
5feet
(1.5meters)
no
no
Fig.1 Typical locations for remote controller
Installation Manual 15
Remote controller installation
Installation of Wired Remote Controller
1. Please fix tightly using provided screw after placing remote controller setup board on the place
where you like to setup.
- Please set it up not to bend because poor setup could take place if setup board bends.
Please set up remote controller board fit to the reclamation box if there is a reclamation box.
2. Can set up Wired remote controller cable into three directions.
- Setup direction: the surface of wall reclamation, upper, right
- If setting up remote controller cable into upper and right side, please set up after removing remote controller cable guide groove.
2
2
h Remove guide groove with long nose.
3
① Reclamation to the surface of the wall
② Upper part guide groove
③ Right part guide groove
3
1
<Wire guide grooves>
3. Please fix remote controller upper part into the
setup board attached to the surface of the wall, as
the picture below, and then, connect with setup
board by pressing lower part.
- Please connect not to make a gap at the remote controller and setup board’s upper and lower, right and
left part.
<Connecting order>
When separating remote controller from setup
board, as the picture below, after inserting into the
lower separating hole using screw driver and then,
spinning clockwise, remote controller is separated.
<Separating order>
- There are two separating holes. Please
individually separate one at a time.
- Please be careful not to damage the inside
components when separating.
16
Wall
Side
Wall
Side
Wall
Side
Wall
Side
Remote controller installation
ENGLISH
4. Please connect indoor unit and remote controller using connection cable.
Please check if connector is normally connected.
Indoor
Unit side
Connecting cable
5. Please use extension cable if the distance between wired remote controller and indoor unit is more
than 10m.
When installing the wired remote controller, do not bury it in the wall.
(It can cause damage in the temperature sensor.)
Do not install the cable to be 50m or above.
(It can cause communication error.)
• When installing the extension cable, check the connecting direction of the connector of the remote controller side and the product side for correct installation.
• If you install the extension cable in the opposite direction, the connector will not be connected.
• Specification of extension cable: 2547 1007 22# 2 core 3 shield 5 or above.
Installation Manual 17
Remote controller installation
Name and function of wired remote controller
1. Operation indication screen
2. Set temperature button
• It will set not room temperature but
outlet air temperature.
1
10
9
8
2
3
7
4
11
12
13
5
6
14
15
Please attach the inform label inside of the door.
Please choose proper language depend on your
country.
3. Fan speed button
• Fan Speed have 3 Steps.
• Middle and Low step is same
4. ON/OFF button
5. Opration mode selection button
6. Wireless remote controller receiver
• Some products don't receive the wireless
signals.
7. Air flow button
8. Subfunction button
9. Function setting button
10. Ventilation button
11. Reservation
12. Up,down,left,right button
• To check the indoor temperature, press
button.
13. Room temperature button
• Displays only the room temperature of the
remote controller perception.
• There is no control of room temperature.
• In case of fresh air intake unit, displays only
the temperature around remote controller.
14. Setting/Cancel button
15. Exit button
※ Some functions may not be operated and displayed depending on the product type.
※ It will display strange value to the room temperature if wired remote controller is not connected.
Model : PQRCVSL0 (Black Color)
PQRCVSL0QW (White Color)
18
Optional Operation
ENGLISH
Optional Operation
Installer Setting -Test Run Mode
After installing the product, you must run a Test Run mode.
For details related to this operation, refer to the product manual.
pressing
button long for 3 seconds,
1 Ifit enters
into remote controller setter
setup mode.
- If pressing once shortly, it enters into
user setup mode. Please press more
than 3 seconds for sure.
- Please cancel the right and left of wind
direction for RAC product.
Function Code
Set
figure '01' blinks at the lower part
2 Setup
of indication window.
3 Press
button to start.
the test run, pressing the below
4 During
button will exit the test run.
- Select operation, temperature
up/down, wind flow control, wind
direction, start/stop button.
Installation Manual 19
Optional Operation
Installer Setting - Setting Address of Central Control
It's the function to use for connecting central control.
Please refer to central controller manual for the details
pressing
button long for 3
1 Ifseconds,
it enters into remote
controller setter setup mode.
- If pressing once shortly, it enters
into user setup mode. Please press
more than 3 seconds for sure.
into address setup mode by using
2 If entering
button, it indicates as picture below.
Indoor No.
Group No
Function Code
Group No. by pressing
3 Set
button.(0~F)
to Indoor No. setting option
4 Move
by pressing
button.
Indoor No. by pressing
5 Set
button.
6 Press
button to save.
button will exit settings mode.
7 Pressing
❈ After setup, it automatically gets out of
setup mode if there is no button input for
25 seconds.
❈ When exiting without pressing set button,
the manipulated value is not reflected.
20
Optional Operation
This is the function to select the temperature sensor to judge the room temperature.
pressing
button long for 3
1 Ifseconds,
it enters into remote
controller setter setup mode.
- If pressing once shortly, it enters
into user setup mode. Please press
more than 3 seconds for sure.
2
If moving to room temperature perception
sensor selection menu by pressing
button, it indicates as picture below.
Thermistor value by pressing
3 Set
button. (01: Remote Controller,
02: Indoor, 03: 2TH)
Function Code
4 Press
Thermistor setting
button to save.
button will exit settings mode.
5 Pressing
❈ After setup, it automatically gets out of
setup mode if there is no button input for
25 seconds.
❈ When exiting without pressing set button,
the manipulated value is not reflected.
<Thermistor Table>
Temperature sensor selection
01 Remote controller
02 Indoor unit
Cooling
03 2TH
Heating
Function
Operation in remote controller temperature sensor
Operation in indoor unit temperature sensor
Operation of higher temperature by comparing indoor unit's and wired remote controller’s temperature.
(There are products that operate at a lower temperature.)
Operation of lower temperature by comparing indoor unit's and wired remote controller's temperature.
j The function of 2TH has different operation characteristics according to the product.
Installation Manual 21
ENGLISH
Installer Setting -Thermistor
Optional Operation
Installer Setting-Group Setting
It is a function for settings in group control, or 2-remote controller control.
pressing
button long for 3
1 Ifseconds,
it enters into remote
controller setter setup mode.
- If pressing once shortly, it enters
into user setup mode. Please press
more than 3 seconds for sure.
2
If pressing
button repeatedly, it moves to
master/slave selection menu as picture
below.
Master/ Slave by pressing
3 Select
button.
(00: Slave, 01: Master)
Function Code
4 Press
Master/Slave value
button to save.
button will exit settings mode.
5 Pressing
❈ After setup, it automatically gets out of
setup mode if there is no button input for
25 seconds.
❈ When exiting without pressing set button,
the manipulated value is not reflected.
Remote controller
Master
Slave
Function
Indoor unit operates based on master remote controller at group control.
(Master is set when delivering from the warehouse.)
Setup all remote controllers except one master remote controller to slave
at group control
h Refer to the 'group control' part for details
• When controlling in groups, basic operation settings, airflow strength weak/medium/strong,
lock setting of the remote controller, time settings, and other functions may be restricted.
22
Optional Operation
Dry contact function is the function that is possible to use only when dry contact equipment is separately purchased/setup.
pressing
button long for 3
1 Ifseconds,
it enters into remote
controller setter setup mode.
- If pressing once shortly, it enters
into user setup mode. Please press
more than 3 seconds for sure.
pressing
button repeatedly, it moves to
2 Ifremote
controller dry contact mode setup
menu as picture below.
Dry contact setting by
3 Select
pressing button.
(00 : Automatic, 01 : manual)
Function Code
4 Press
Dry Contact
setting value
button to save.
button will exit settings mode.
5 Pressing
❈ After setup, it automatically gets out of
setup mode if there is no button input for
25 seconds.
❈ When exiting without pressing set button,
the manipulated value is not reflected.
▶ What is Dry Contact?
Like hotel card key and body perception sensor, it is the signal of the point of contact when using
air-conditioner by interlocking.
• Please refer to dry contact manual for more details.
Installation Manual 23
ENGLISH
Installer Setting-Dry Contact Mode Setting
Optional Operation
Installer Setting-Celsius / Fahrenheit Switching
This function is used for switching the display between Celsius and Fahrenheit.
(Optimized only for U.S.A)
pressing
button long for 3
1 Ifseconds,
it enters into remote
controller setter setup mode.
- If pressing once shortly, it
enters into user setup mode.
Please press more than 3 seconds for
sure.
pressing
2 Repeat
Function code 12.
button to select
Function Code
conversion mode value
Ex) Fahrengeit Setting
Temperature unit mode by
3 Select
pressing
button.
(00: Celsius, 01: Fahrenheit)
4 Press
button to save or release.
button to exit or
5 Press
system will automatically exit
after 25 seconds without any
input.
h Whenever press
grees.
24
button in Fahrenheit mode, the temperature will increase/drop 2 de-
Optional Operation
Setting feature for indoor unit when air cleaning / heater / humidifier / Up/down grill / Ventilation
KIT /Auxiliary Heater is newly installed, or installed unit is removed.
pressing
button long for 3
1 Ifseconds,
it enters into remote
controller setter setup mode.
- If pressing once shortly, it enters
into user setup mode. Please press
more than 3 seconds for sure.
button repeatedly, it moves to
2 Ifthepressing
selected option function code as picture
below.
Function
Plasma purification
Electric heater
Dehumidifier
Elevation grill
Ventilation kit
Auxiliary heater
Code
20
21
22
23
24
25
existing condition
3 Select
of each mode by pressing
button.
(00: not installed,
01 : installed)
Function Code
4 Press
Existing condition
button to save.
button will exit settings mode.
5 Pressing
❈ After setup, it automatically gets out of
setup mode if there is no button input for
25 seconds.
❈ When exiting without pressing set button,
the manipulated value is not reflected.
Installation Manual 25
ENGLISH
Installer Setting -Optional Function Setting
How to Set E.S.P?
How to Set E.S.P?
Installer Setting -E.S.P.
This is the function that decides the strength of the wind for each wind level and because this function
is to make the installation easier.
• If you set ESP incorrectly, the air conditioner may malfunction.
• This setting must be carried out by a certificated-technician.
ESP value
Function code,
ESP code
to ESP value setting by pressing
4 Movebutton.
(It is 000 when delivering
from the warehouse.)
5 Press
pressing
button long for 3
1 Ifseconds,
it enters into remote
button to setup ESP value.
(It is possible to setup ESP
value from 1 to 255, and 1 is
the smallest and 255 is the
biggest.)
controller setter setup mode.
- If pressing once shortly, it enters
into user setup mode. Please press
more than 3 seconds for sure.
ESP fan step again by using
into ESP setup mode by using
6 Select
2 If entering
button and setup ESP value, as No. 4
button, it indicates as the picture
and 5, that corresponds each wind flow
below.
7
ESP step
Function Code
ESP fan step by
3 Select
pressing
button.
(01: very low, 02: low, 03:
medium, 04: high, 05:
very high)
Press
button to save.
ESP value
button to exit.
8 Press
❈ After setup, it automatically gets out of
setup mode if there is no button input
for 25 seconds.
❈ When exiting without pressing set
button, the manipulated value is not
reflected.
• When setting ESP value on the product without very weak wind or power wind function, it may not work.
• Please be careful not to change the ESP value for each fan step.
• It does
notESP
work
to setup
value
forvery
veryweak
low/power
step for
products.
h When
setting
value
on the ESP
product
without
wind or power
windsome
function,
it may not work.
• ESP value is available for specific range belongs to the product.
26
How to Set E.S.P?
Setting Value
60
65
70
75
80
85
90
95
100
105
110
115
120
125
130
(Unit : CMM)
0 (0)
5.03
5.60
6.19
6.79
7.41
8.05
8.71
9.38
10.07
-
1 (10)
4.85
5.44
6.05
6.67
7.31
7.96
8.63
9.32
10.03
-
Static Pressure(mmAq(Pa))
2 (20)
3 (30)
4.57
5.17
5.80
4.80
6.43
5.44
7.09
6.09
7.76
6.76
8.45
7.45
9.16
8.16
9.88
8.88
9.62
10.38
-
4 (40)
4.97
5.64
6.33
7.04
7.76
8.50
9.26
10.03
ABNH12GL2A2, ABNH18GL2A2
Setting Value
75
80
85
90
95
100
105
110
115
120
125
130
135
140
145
0 (0)
6.50
7.34
8.20
9.07
9.96
10.87
11.79
12.73
13.69
14.67
15.66
16.67
-
(Unit : CMM)
1 (10)
6.70
7.55
8.43
9.32
10.22
11.15
12.09
13.05
14.02
15.01
16.02
-
Static Pressure(mmAq(Pa))
2 (20)
3 (30)
6.69
7.56
6.47
8.45
7.36
9.36
8.27
10.28
9.19
11.22
10.14
12.18
11.09
13.16
12.07
14.15
13.06
15.16
14.07
16.18
15.10
16.14
-
1 (10)
10.71
12.34
13.69
14.83
15.85
16.80
17.79
18.87
20.13
21.64
-
Static Pressure(mmAq(Pa))
2 (20)
3 (30)
11.09
12.19
13.38
10.71
14.36
11.85
15.23
12.86
16.07
13.82
16.93
14.80
17.89
15.88
19.01
17.14
20.36
18.66
22.01
20.50
22.75
4 (40)
6.96
7.89
8.83
9.78
10.76
11.75
12.76
13.79
14.83
15.89
ABNH24GL3A2
Setting Value
85
90
95
100
105
110
115
120
125
130
135
140
145
5 (50)
5.08
5.79
6.51
7.25
8.01
8.78
5 (50)
6.35
7.30
8.25
9.23
10.22
11.23
12.26
13.30
14.36
(Unit : CMM)
0 (0)
10.19
12.18
13.81
15.16
16.30
17.31
18.27
19.26
20.34
21.60
-
4 (40)
10.97
11.93
12.91
13.99
15.25
16.76
18.61
20.86
5 (50)
10.49
11.57
12.83
14.35
16.19
18.44
Note :
1. The above table shows the correlation between the air rates and E.S.P.
Installation Manual 27
ENGLISH
ABNH09GL1A2
Self-diagnosis Function / Dip Switch Setting
Self-diagnosis Function
Indoor Unit Error
Ex) Error 03 (Remote controller error)
3 Times
3 Times
3 Times
LED02G
(GREEN)
2 Sec.
Description
Error Code
01
02
03
04
05
06
09
10
2 Sec.
Indoor Room sensor error
Indoor in-pipe sensor error
Remote controller error
Drain pump error
Communication error indoor and outdoor
Indoor out-pipe sensor error
EEPROM error (indoor)
BLDC motor fan lock (indoor)
LED 1
(Red)
LED 2
(Green)
Indoor
status
0
0
0
0
0
0
0
1time ◑
1time ◑
2times ◑
3times ◑
4times ◑
5times ◑
6times ◑
9times ◑
0
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
h Because remote controller turn off when occur ERROR in simultaneous operation system, it
should check LED blinks of outdoor in order to confirm error code.
h Repeatedly after LED1 is turned on and off as the Error code number of tens digit, LED2 is turned
on and off as the Error code number of single-digit.
Dip Switch Setting
Indoor PCB
Function
Description
Setting Off
Setting On
Default
Selection of Master or Slave
Master
Slave
Off
SW4 Dry Contact Mode
Selection of Dry Contact
Mode
Wired/Wireless remote
controller
Selection of Manual or Auto
operation Mode
Auto
Off
SW5
Fan continuous operation
Continuous operation Removal
Working
Off
SW3
28
Group Control
Installation
İTHALATÇI FİRMA
LG ELECTRONICS TİCARET A.Ş.
Kaptanpaşa Mahallesi Piyalepaşa Bulvarı
No:73 Ortadoğu Plaza Kat:7 34384
Okmeydanı / Şişli / İstanbul
Tel: (0 212) 314 52 52
Faks: (0 212) 222 61 44
ÜRETİCİ FİRMA
LG Electronics Inc.
Changwon 2nd factory 84, Wanam-ro,
Seongsan-gu, Changwon-si
Gyeongsangnam-do, KOREA
www.lg.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising