LG | APNQ48LT3E3.ENWBEVH | Owner's Manual | LG APNQ48LT3E3.ENWBEVH Owner's Manual

LG APNQ48LT3E3.ENWBEVH Owner's Manual
1,MFL67724515,
2017. 12. 20.
4:55 Page 1
ENGLISH
Tiếng Việt
BAHASA INDONESIA
OWNER’S MANUAL
AIR
CONDITIONER
Please read this manual carefully before operating your set and retain it for future
reference.
Floor Standing
I.15.LEI3.02843.0717
www.lg.com
P/NO : MFL67724515
Copyright © 2016 - 2017 LG Electronics Inc. All Rights Reserved.
1,MFL67724515,
2
2017. 12. 20.
4:55 Page 2
TIPS FOR SAVING ENERGY
ENGLISH
TIPS FOR SAVING ENERGY
Here are some tips that will help you minimize the power consumption when you use the air
conditioner. You can use your air conditioner more efficiently by referring to the instructions
below:
• Do not cool excessively indoors. This may be harmful for your health and may consume more
electricity.
• Block sunlight with blinds or curtains while you are operating the air conditioner.
• Keep doors and windows closed tightly while you are operating the air conditioner.
• Adjust the direction of the air flow vertically or horizontally to circulate indoor air.
• Speed up the fan to cool indoor air quickly, in a short period of time.
• Clean the air filter once every 2 weeks. Dust and impurities collected in the air filter may block
the air flow or weaken the cooling / dehumidifying functions.
For your records
Staple your receipt to this page in case you need it to prove the date of purchase or for warranty
purposes. Write the model number and the serial number here:
Model number :
Serial number :
You can find them on a label on the side of each unit.
Dealer’s name :
Date of purchase :
1,MFL67724515,
2017. 12. 20.
4:55 Page 3
IMPORTANT SAFETY INSTRUCTIONS
3
READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.
Always comply with the following precautions to avoid dangerous situations and ensure peak
performance of your product
! WARNING
It can result in serious injury or death when the directions are ignored
! CAUTION
It can result in minor injury or product damage when the directions are ignored
! WARNING
• Install or repair by unqualified persons can result in hazards to you and others.
• Installation MUST comply with local building codes. If there is no local codes, comply with the
Nation Electrical Code NFPA 70/ANSI C1-1003, Canadian Electrical Code Part1 CSA C.22.1. or
current edition.
• The information contained in the manual is intended for use by a qualified service technician
familiar with safety procedures and equipped with the proper tools and test instruments.
• Failure to carefully read and follow all instructions in this manual can result in equipment malfunction, property damage, personal injury or death.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Installation
• Do not install duct through disassemble or repair the product yourself.
- This product can not install duct.
• Do not use a defective or underrated circuit breaker. Use this appliance on a dedicated circuit.
- There is risk of fire or electric shock.
• For electrical work, contact the dealer, seller, a qualified electrician, or an authorized service center.
- Do not disassemble or repair the product. There is risk of fire or electric shock.
• Always ground the product.
- There is risk of fire or electric shock.
• Install the panel and the cover of control box securely.
- There is risk of fire or electric shock.
• Always install a dedicated circuit and breaker.
- Improper wiring or installation may cause fire or electric shock.
• Use the correctly rated breaker or fuse.
- There is risk of fire or electric shock.
• Do not modify or extend the power cable.
- There is risk of fire or electric shock.
• Do not let the air conditioner run for a long time when the humidity is very high and a door or a window is left open.
- Moisture may condense and wet or damage furniture.
• Be cautious when unpacking and installing the product.
- Sharp edges could cause injury. Be especially careful of the case edges and the fins on the condenser and evaporator.
• For installation, always contact the dealer or an authorized service center.
- There is risk of fire, electric shock, explosion, or injury.
ENGLISH
IMPORTANT SAFETY INSTRUCTIONS
1,MFL67724515,
4
2017. 12. 20.
4:55 Page 4
IMPORTANT SAFETY INSTRUCTIONS
ENGLISH
• Do not install the product on a defective installation stand.
- It may cause injury, accident, or damage to the product.
• Be sure the installation area does not deteriorate with age.
- If the base collapses, the air conditioner could fall with it, causing property damage, product failure,
and personal injury.
• Use a vacuum pump or Inert (nitrogen) gas when doing leakage test or air purge. Do not compress
air or Oxygen and do not use Flammable gases. Otherwise, it may cause fire or explosion.
- There is the risk of death, injury, fire or explosion.
• Do not turn on the breaker or power under condition that front panel, cabinet, top cover, control box
cover are removed or opened. Otherwise, it may cause fire, electric shock, explosion or death.
Operation
• Take care to ensure that power cable could not be pulled out or damaged during operation.
There is risk of fire or electric shock.
• Do not place anything on the power cable. There is risk of fire or electric shock.
• Do not touch(operate) the product with wet hands. There is risk of fire or electrical shock.
• Do not place a heater or other appliances near the power cable. There is risk of fire and electric shock.
• Do not allow water to run into electric parts. There is risk of fire, failure of the product, or electric shock.
• Do not store or use flammable gas or combustibles near the product. There is risk of fire or
failure of product.
• Do not use the product in a tightly closed space for a long time. Oxygen deficiency could
occur.
• When flammable gas leaks, turn off the gas and open a window for ventilation before turn the
product on. Do not use the telephone or turn switches on or off. There is risk of explosion or
fire.
• If strange sound, smell or smoke comes from product, turn the breaker off or disconnect the
power supply cable. There is risk of electric shock or fire.
• Stop operation and close the window in storm or hurricane. If possible, remove the product
from the window before the hurricane arrives. There is risk of property damage, failure of
product or electric shock.
• Do not open the inlet grill of the product during operation.(Do not touch the electrostatic filter,
if the unit is so equipped.) There is risk of physical injury, electric shock, or product failure.
• When the product is soaked (flooded or submerged), contact an authorized service center.
There is risk of fire or electric shock.
• Be cautious that water could not enter the product. There is risk of fire, electric shock, or
product damage.
• Ventilate the product from time to time when operating it together with a stove, etc. There is
risk of fire or electric shock.
• Turn the main power off when cleaning or maintaining the product. There is risk of electric
shock.
• When the product is not be used for a long time or the product use first time after test running, turn on main power switch before 6hours ago.
• Take care to ensure that nobody could step on or fall onto the outdoor unit. This could result
in personal injury and product damage.
1,MFL67724515,
2017. 12. 20.
4:55 Page 5
IMPORTANT SAFETY INSTRUCTIONS
5
• Always check for gas (refrigerant) leakage after installation or repair of product. Low refrigerant levels may cause failure of product.
• Install the drain hose to ensure that water is drained away properly. A bad connection may cause
water leakage.
• Keep level even when installing the product. To avoid vibration or water leakage.
• Do not install the product where the noise or hot air from the outdoor unit could damage the neighborhoods. It may cause a problem for your neighbors.
• Use two or more people to lift and transport the product. Avoid personal injury.
• Do not install the product where it will be exposed to sea wind (salt spray) directly. It may cause corrosion on the product. Corrosion, particularly on the condenser and evaporator fins, could cause
product malfunction or inefficient operation.
Operation
• Do not expose the skin directly to cool air for long periods of time. (Don't sit in the draft.) This could
harm to your health.
• Do not use the product for special purposes such as preserving foods, works of art, etc. It is a consumer air conditioner, not a precision refrigeration system. There is risk of damage or loss of property.
• Do not block the inlet or outlet of air flow. It may cause product failure.
• Use a soft cloth to clean. Do not use harsh detergents, solvents, etc. There is risk of fire, electric
shock, or damage to the plastic parts of the product.
• Do not touch the metal parts of the product when removing the air filter. They are very sharp! There
is risk of personal injury.
• Do not step on or put anything on the product. (outdoor units) There is risk of personal injury and
failure of product.
• Always insert the filter securely. Clean the filter every two weeks or more often if necessary. A dirty
filter reduces the efficiency of the air conditioner and could cause product malfunction or damage.
• Do not insert hands or other objects through the air inlet or outlet while the product is operated.
There are sharp and moving parts that could cause personal injury.
• Do not drink the water drained from the product. It is not sanitary and could cause serious health issues.
• Use a firm stool or ladder when cleaning or maintaining the product. Be careful and avoid personal
injury.
• Replace the all batteries in the remote control with new ones of the same type. Do not mix old and
new batteries or different types of batteries. There is risk of fire or explosion
• Do not recharge or disassemble the batteries. Do not dispose of batteries in a fire. They may burn or
explode.
• If the liquid from the batteries gets onto your skin or clothes, wash it well with clean water. Do not
use the remote if the batteries have leaked. The chemicals in batteries could cause burns or other
health hazards.
• If you eat the liquid from the batteries, brush your teeth and see doctor. Do not use the remote if
the batteries have leaked. The chemicals in batteries could cause burns or other health hazards.
ENGLISH
! CAUTION
Installation
1,MFL67724515,
6
2017. 12. 20.
4:55 Page 6
TABLE OF CONTENTS
ENGLISH
TABLE OF CONTENTS
2
3
7
TIPS FOR SAVING ENERGY
7
7
7
7
Preparing for operation
Usage
Cleaning and maintenance
Service
8
PRODUCT INTRODUCTION
8
9
10
11
Name of parts
Indoor unit controls and indicators
Wireless remote controller
Remote control preparation
IMPORTANT SAFETY INSTRUCTIONS
BEFORE USE
12 OPERATING INSTRUCTIONS
12
12
12
13
13
13
13
14
14
15
Cooling Mode
Airflow Setting
Fan Speed Setting
Dehumidification Mode
Power Cooling Mode
Fan Mode
Simple Reservation
Child Lock Operation Function
Auto Dry Function
Auto Restart Operation
16 MAINTENANCE AND SERVICE
16
17
18
18
Indoor Unit
Operation Tips
Troubleshooting Tips! Save time and money!
Call the service immediately in the following situations
1,MFL67724515,
2017. 12. 20.
4:55 Page 7
BEFORE USE
7
Preparing for operation
• Contact an installation specialist for installation.
• Use a dedicated circuit.
Usage
• Being exposed to direct airflow for an extended period of time could be hazardous to your
health. Do not expose occupants, pets, or plants to direct airflow for extended period of time.
• Due to the possibility of oxygen deficiency, ventilate the room when used together with stoves
or other heating devices.
• Do not use this air conditioner for non-specified special purposes (e.g. preserving precision devices, food, pets, plants, and art objects). Such usage could damage the items.
Cleaning and maintenance
• Do not touch the metal parts of the unit when removing the filter. Injuries can occur when handling sharp metal edges.
• Do not use water to clean inside the air conditioner. Exposure to water can destroy the insulation, leading to possible electric shock.
• When cleaning the unit, first make sure that the power and breaker are turned off. The fan rotates at a very high speed during operation. There is a possibility of injury if the unit’s power is
accidentally triggered on while cleaning inner parts of the unit.
Service
For repair and maintenance, contact your authorized service dealer.
ENGLISH
BEFORE USE
1,MFL67724515,
8
2017. 12. 20.
4:55 Page 8
PRODUCT INTRODUCTION
ENGLISH
PRODUCT INTRODUCTION
Name of parts
Indoor unit
1
2
3
4
5
6
Left/Right Airflow Control Louver
Up/Down Airflow Control Louver
Display Panel
Air filter
Air Inlet
Control Box
1
2
3
4
5
6
1,MFL67724515,
2017. 12. 20.
4:55 Page 9
PRODUCT INTRODUCTION
ENGLISH
Indoor unit controls and indicators
1
3
5
6
4
2
11
MODE
7
8
1. Timer
2. Dehumidification operation lamp
3. Cooling operation lamp
4. Fan mode operation lamp
5. Room temp. / Set temp. display
6. Indoor fan speed lamp
7. ON/OFF button
8. Operation mode selection button
9. Room temperature setting button
10. Indoor fan speed button
11. Signal receptor
9
9
10
1,MFL67724515,
2017. 12. 20.
4:55 Page 10
10 PRODUCT INTRODUCTION
ENGLISH
Wireless remote controller
Control
panel
Description
Remote control operation lamp
|
4
FAN SPD
Power ON/OFF button : Operation will start
when this button is pressed, and stop when
the button is pressed again.
Indoor fan speed button : To select the desired
fan speed.
Temperature setting button
A
Cooling button
Auto dry button : If setting this function,
evaporator will be automatically dried before
turning off the air conditioner.
D
Dehumidification button : Can effectively
remove humidity when at the time of rainy
season or high humidity.
Artificial intelligence
Fan mode button
Air flow direction button(Up/down, Left/right) :
Adjust air flow direction vertically or
horizontally.
Power cooling mode button : Powerful cooling
is performed
ON/OFF timer setting button : Set the time of
starting or stopping
Timer cancel button
* Some function does not operate according to model.
Handling the remote control
- Aim at the signal receptor on the floor standing type air
conditioner when operating.
- Block a strong light over the signal receptor with a curtain or
etc. so as to prevent the abnormal operation. (ex: electronic
quick start, ELBA, inverter type fluorescent lamp)
- Be sure that there are no obstructions between the remote
control and the signal receptor.
- Do not drop or throw the remote control.
- Do not place the remote control in a location exposed to
direct sunlight, or next to a heating unit, or other heat
source.
1,MFL67724515,
2017. 12. 20.
4:55 Page 11
PRODUCT INTRODUCTION
11
ENGLISH
Remote control preparation
How to mount onto a wall
1 Use the screws to secure the holder to the
wall.
2 To insert the remote control to the holder.
- Do not use rechargeable batteries such batteries are different from standard dry cells in
shape, dimensions, and performance.
- Change the batteries with a new one if the
remote control does not work properly after
using for an extended period of time.
! CAUTION
How to insert batteries
1 Remove the cover from the back of the remote controller.
- Slide the cover according to the arrow direction.
2 Insert two batteries.
- Be sure that the (+) and (-) directions are
correct.
- Be sure that both batteries are new.
3 Re-attach the cover.
- Slide the cover into back position.
• When not using remote controller for a
long time, flowing of dry cell liquid may
cause the failure of product, therefore,
remove all dry cells.
• When replacing dry cell (AAA), replace
two of them all with new ones, and if remote controller is not operated properly
even after replacing the dry cells (AAA),
request the service.
• Do not disassemble or re-charge the
used dry cells, and do not throw away
those at the location with heat of fire or
hot air. There will be the danger of explosion.
1,MFL67724515,
2017. 12. 20.
4:55 Page 12
12 OPERATING INSTRUCTIONS
ENGLISH
OPERATING INSTRUCTIONS
Cooling Mode
Fan Speed Setting
1 Press | button to turn on the indoor.
1 Press | button to turn on the indoor.
2 Press a button to select Cooling opera-
2 Press
tion mode.
- When canceling operating, press | button once more.
3 Adjust the desired temperature by pressing (
) buttons.
- If desired temperature is higher than
room temperature, cooling cannot be conducted.
- Set the temperature lower than the room
temperature
- Setting Temp Range : 18 °C~30 °C.
!
NOTE
What is 3 minutes delay function?
The reason that cold wind is not coming out
when operating the unit after turning off the
cooling is because of the function to protect
compressor. Cold wind will be coming out
when compressor is operated after 3 minutes.
Airflow Setting
We can simply adjust the desired airflow direction.
Up/Down Airflow Direction Control
1 Press | button to turn on the indoor.
2 Press I button and the louvers will
swing up and down.
3 Press I button again to set the horizontal
louver at the desired airflow direction.
Left/Right Airflow Direction Control
1 Press | button to turn on the indoor.
2 Press J button and the louvers will
swing left and right.
3 Press J button again to set the vertical
louver at the desired airflow direction.
button to select fan speed.
- You can select the fan speed in four
steps Low, Med, High, Super High.
Each time the button is pressed, the fan
speed mode is shifted.
- Air flow rate can be selected during the
cooling, dehumidification and blowing
mode.
1,MFL67724515,
2017. 12. 20.
4:55 Page 13
OPERATING INSTRUCTIONS 13
Cooling only
In rainy season or high humidity climate, it is
possible to operate simultaneously dehumidifier and cooling mode to remove humidity effectively.
Simple Reservation
Turning ON reservation mode
This function is able to turn on unit after a setting time.
1 When the unit is turned off, adjust desired
1 Press | button to turn on the indoor.
setting time with
2 Press c button to select dehumidification
- Up to the maximum of 24 hours can be
selected.
mode
- Room temperature will be displayed after
desired temperature is indicated at display section for about 5 seconds.
button.
Turning OFF reservation mode
This function is able to turn off unit after a setting time.
1 When the unit is turned on, adjust desired
Power Cooling Mode
Strong cooling will be conducted in short time.
1 Press | button to turn on the indoor.
2 Press
button to operate power cooling
mode.
- When power cooling button is pressed
during cooling/dehumidification mode,
power cooling will be operated.
In power cooling mode, desired temperature is set to 18 °C and the horizontal louver is fixed at the highest position.
Fan Mode
1 Press | button to turn on the indoor unit.
2 Press
button to circulate indoor air.
- When canceling operation, press
button once more.
- During fan mode, outdoor fan and compressor will not be operated.
- During fan mode, indoor unit turns on the
fan mode lamp, room temperature lamp,
and fan speed lamp of its display panel.
setting time with
button.
- Up to the maximum of 7 hours can be selected.
!
NOTE
After performing the setting, if corresponded
setting button is pressed once, remaining setting time will be displayed, and if it is pressed
once again, corresponded setting function will
be cancelled. (same function as
) Remaining
setting time will be displayed with the unit of 1
hour.
ENGLISH
Dehumidification Mode
1,MFL67724515,
2017. 12. 20.
4:55 Page 14
14 OPERATING INSTRUCTIONS
ENGLISH
Child Lock Operation Function
Auto Dry Function
1 Press the
1 Auto dry function can be setted/released
and high
simultaneously
for 3 seconds.
2 During child lock operation,
- Whenever you press any button on display panel, it will immediately display
"CL", which means display panel is
locked.
- All the button on the indoor unit display
panel will not work.
- But the button on the remote controller
will be operated.
by manipulating indoor unit button or remote control.
2 When pressing the
button after setting
the function, evaporator in indoor unit will
be automatically dried as showing counting
00 to 99 on its display panel .
3 After indicating 99 on the display panel,
the unit will be automatically turned off.
* Auto dry function is released at initial
state as standard.
3 Press the
and high
simultaneously
for 3 seconds again. The unit will respond
with beep. child lock operation will removed
For Setting Auto Dry Function
If manipulating indoor unit, press the
button and
button simultaneously for 3
seconds.
If manipulating remote control for Cooling
Only model, press
button.
The indoor unit will respond with beep once
and indicate “SC” on its display panel. Then
Auto dry function will be set.
MODE
MODE
For Releasing Auto Dry Function
If manipulating indoor unit, press the
button and
button simultaneously for 3
seconds.
If manipulating remote control, press
button.
The indoor unit will respond with beep twice
and Auto dry function will be removed.
MODE
MODE
1,MFL67724515,
2017. 12. 20.
4:55 Page 15
OPERATING INSTRUCTIONS 15
When power is supplied again after unit operation has been stopped because of interruption of power supply due to outage or other
causes, auto re-operation will be performed by
remembering previous setting.
- When power is supplied, outdoor unit operation will be started within 3 minutes.
1 Auto Restart Operation can be established/released by manipulating indoor unit
button.
* When initial state, Auto Restart Operation will be set up as standard.
For Releasing Restart Operation
Press the
,
,
,
taneously for 3 seconds.
(4 buttons) simul-
The unit will respond with beep and Restart
Operation will be removed.
For Setting Restart Operation
After function release, Press the
,
,
,
(4 buttons) simultaneously for 3 seconds.
The unit will respond with beep and restart
operation will be setted.
MODE
ENGLISH
Auto Restart Operation
1,MFL67724515,
2017. 12. 20.
4:55 Page 16
16 MAINTENANCE AND SERVICE
ENGLISH
MAINTENANCE AND SERVICE
Filter Cleaning
Indoor Unit
Grille, Case and Remote Control
- Turn the system off before cleaning, To
clean, wipe with a soft, dry cloth. Do not use
bleach or abrasives.
!
Please clean it once in a week.
1 Remove the Air filters.
- Take hold of the tab and pull slightly forward to remove the filter.
! CAUTION
NOTE
Supply power must be disconnected before cleaning the indoor unit.
When the air filter is to be removed, do
not touch the metal parts of the indoor
unit. It may cause an injury.
Air Filters
The air filters behind the front grille should be
checked and cleaned once every 2 weeks or
more often if necessary.
- Never use any of the followings:
Water hotter than 40 °C.
Could cause deformation and/or discoloration.
Volatile substances.
Could damage the surfaces of the air conditioner.
2 Clean dirt from the air filter using a vacuum
cleaner or washing with water.
- If dirt is conspicuous, wash with a neutral
detergent in lukewarm water.
SI
Be
n zene
N NER
SCO
U RIN G
C LB
A R GER
- If hot water (40 °C or more) is used, it
may be deformed.
3 After washing with water, dry well in the
shade.
- Do not expose the air filter to direct sunlight or heat from a fire when drying it.
4 Install the air filter.
1,MFL67724515,
2017. 12. 20.
4:55 Page 17
MAINTENANCE AND SERVICE 17
1 Operate the air conditioner at the following
settings for 2 to 3 hours.
- Type of operation: Fan operation mode.
- This will dry out the internal mechanisms.
When the air conditioner is to be
used again.
1 Clean the air filter and install it in the indoor unit.
2 Check that the air inlet and outlet of the indoor/outdoor unit are not blocked.
3 Check that the ground wire is connected
! CAUTION
correctly. It may be connect to the indoor
unit side.
Turn off the breaker when the air conditioner is not going to be used for a long
time.
Dirt may collect and may cause a fire.
Helpful information
The air filters and your electiric bill.
If the air filters become clogged with dust, the
cooling capacity will drop, and 6 % of the electricity used to operate the air conditioner will
be wasted.
Operation Tips
Do not overcool the room.
This is not good for the health
and wastes electricity.
Keep blinds or curtains closed.
Do not let direct sunshine
enter the room when the air
conditioner is in operation.
Keep the room temperature
uniform.
Adjust the vertical and horizontal airflow direction to ensure a
uniform temperature in the
room.
Make sure that the doors
and windows are shut tight.
Avoid opening doors and windows as much as possible to
keep the cool air in the room.
Clean the air filter regularly.
Blockages in the air filter reduces the airflow and lowers
the cooling and dehumidifying
effects. Clean at least once
every two weeks.
Ventilate the room occasionally.
Since windows are kept
closed, it is a good idea to
open them and ventilate the
room now and then.
ENGLISH
When air conditioner is not going
to be used for a long time.
1,MFL67724515,
2017. 12. 20.
4:55 Page 18
18 MAINTENANCE AND SERVICE
ENGLISH
Troubleshooting Tips! Save time and money!
Check the following points before requesting repairs or service.... If the malfunction persist,
please contact your dealer.
The air conditioner
The room has a pecudoes not operate.
liar odor.
- Have you made a
- Check that this is not
mistake in timer oper- a damp smell exuded
ation?
by the walls, carpet,
furniture or cloth
- Has the fuse blown
items in the room.
or has the circuit
breaker been tripped?
Does not cool effectively.
- Is the air filter dirty?
See air filter cleaning
instructions.
- The room may have
been very hot when
the room air conditioner was first turned
on. Allow time for it
to cool down.
- Has the temperature
been set incorrectly?
- Are the indoor unit's
air inlet or outlet
vents obstructed?
It seems that condensation is leaking from
the air conditioner.
- Condensation occurs
when the airflow
from the air conditioner cools the warm
room air.
The air conditioner op- Crack sound is heard.
eration is noisy.
- This sound is gener- For a noise that
ated by the expansounds like water
sion/constriction of
flowing.
the front panel, etc.
* This is the sound of due to changes of
freon flowing inside temperature.
the air conditioner
unit.
- For a noise that
sounds like the compressed air releasing
into atmosphere.
- This is the sound of
the dehumidifying
water being
processed inside the
air conditioning unit.
Air conditioner does
not operate for about 3
minutes when restart.
- This is the protector
of the mechanism.
- Wait about three minutes and operation
will begin.
Remote control display
is faint, or no display at
all.
- Are the batteries depleted?
- Are the batteries inserted in the opposite
(+) and (-) directions?
The error code is occurred after lightning
struck
- This product has
been applied to the
over current protection circuit.
Error can occur, but it
is normal behavior.
After few minutes, It
will operate normally.
Call the service immediately in the following situations
1 Anything abnormal such as burning smell, loud noise etc. happen. Stop the unit and turn the
2
3
4
5
breaker off. Never try to repair by yourself or restart the system in such cases.
Main power cord is too hot or damaged.
Error code is generated by self diagnosis.
Water leaks from indoor unit even if the humidity is low.
Any switch, breaker (safety, earth) or fuse fails to work properly
User must carry routine checkup & cleaning to avoid unit’s poor performance.
In case of special situation, the job must be carried out by service person only.
1,MFL67724515,
2017. 12. 20.
4:55 Page 19
19
ENGLISH
1,MFL67724515,
2017. 12. 20.
4:55 Page 100
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising