LG TB106 User guide

LG TB106 User guide
ENGLISH
DEUTSCH
FRANÇAIS
NEDERLANDS
SLOVENŠČINA
ITALIANO
OWNER’S MANUAL
ΕΛΛΗΝΙΚΑ
Please read this manual carefully before operating
your set and retain it for future reference.
PORTUGUÊS
TB106 (TB106, TBS106V)
TB106-D0F-ADEULL-ENG.indd 1
ESPAÑOL
DVD Micro Hi-Fi System
11. 11. 30
2:16
2
Getting Started
Safety Information
1
CAUTION
Getting Started
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE COVER (OR BACK) NO
USER-SERVICEABLE PARTS INSIDE REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with
arrowhead symbol within an
equilateral triangle is intended to
alert the user to the presence of
uninsulated dangerous voltage
within the product’s enclosure that
may be of sufficient magnitude to
constitute a risk of electric shock
to persons.
The exclamation point within an
equilateral triangle is intended
to alert the user to the presence
of important operating and
maintenance (servicing)
instructions in the literature
accompanying the product.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK
HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE.
WARNING: Do not install this equipment in a
confined space such as a book case or similar unit.
CAUTION: Do not block any ventilation openings.
Install in accordance with the manufacturer’s
instructions.
Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the
product and to protect it from over heating. The
openings shall be never be blocked by placing
the product on a bed, sofa, rug or other similar
surface. This product shall not be placed in a builtin installation such as a bookcase or rack unless
proper ventilation is provided or the manufacturer’s
instruction has been adhered to.
TB106-D0F-ADEULL-ENG.indd 2
CAUTION: This product employs a Laser System.
To ensure proper use of this product, please read
this owner’s manual carefully and retain it for future
reference. Shall the unit require maintenance,
contact an authorized service center.
Use of controls, adjustments or the performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try
to open the enclosure. Visible laser radiation when
open. DO NOT STARE INTO BEAM.
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon
a dedicated circuit;
That is, a single outlet circuit which powers only
that appliance and has no additional outlets or
branch circuits. Check the specification page of this
owner’s manual to be certain. Do not overload wall
outlets. Overloaded wall outlets, loose or damaged
wall outlets, extension cords, frayed power cords, or
damaged or cracked wire insulation are dangerous.
Any of these conditions could result in electric
shock or fire. Periodically examine the cord of your
appliance, and if its appearance indicates damage
or deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with an
exact replacement part by an authorized service
center. Protect the power cord from physical or
mechanical abuse, such as being twisted, kinked,
pinched, closed in a door, or walked upon. Pay
particular attention to plugs, wall outlets, and
the point where the cord exits the appliance. To
disconnect power from the mains, pull out the
mains cord plug. When installing the product,
ensure that the plug is easily accessible.
11. 11. 30
2:16
Getting Started
This device is equipped with a portable battery or
accumulator.
CAUTION: The apparatus shall not be exposed to
water (dripping or splashing) and no objects filled
with liquids, such as vases, shall be placed on the
apparatus.
Disposal of your old appliance
1. When this crossed-out wheeled bin
symbol is attached to a product it
means the product is covered by the
European Directive 2002/96/EC.
2. All electrical and electronic products
should be disposed of separately
from the municipal waste stream
via designated collection facilities
appointed by the government or the
local authorities.
3. The correct disposal of your old
appliance will help prevent potential
negative consequences for the
environment and human health.
Copyrights
It is forbidden by law to copy, broadcast, show,
broadcast via cable, play in public, or rent
copyrighted material without permission. This
product features the copy protection function
developed by Macrovision. Copy protection signals
are recorded on some discs. When recording and
playing the pictures of these discs picture noise
will appear. This product incorporates copyright
protection technology that is protected by U.S.
patents and other intellectual property rights. Use
of this copyright protection technology must be
authorized by Macrovision, and is intended for
home and other limited viewing uses only unless
otherwise authorized by Macrovision. Reverse
engineering or disassembly is prohibited.
1
Getting Started
Safety way to remove the battery or the battery
from the equipment: Remove the old battery
or battery pack, follow the steps in reverse order
than the assembly. To prevent contamination of
the environment and bring on possible threat
to human and animal health, the old battery or
the battery put it in the appropriate container at
designated collection points. Do not dispose of
batteries or battery together with other waste. It is
recomended that you use local, free reimbursement
systems batteries and accumulators. The battery
shall not be exposed to excessive heat such as
sunshine, fire or the like.
3
CONSUMERS SHOULD NOTE THAT NOT ALL
HIGH DEFINITION TELEVISION SETS ARE FULLY
COMPATIBLE WITH THIS PRODUCT AND MAY CAUSE
ARTIFACTS TO BE DISPLAYED IN THE PICTURE. IN
CASE OF 525 OR 625 PROGRESSIVE SCAN PICTURE
PROBLEMS, IT IS RECOMMENDED THAT THE USER
SWITCH THE CONNECTION TO THE ‘STANDARD
DEFINITION’ OUTPUT. IF THERE ARE QUESTIONS
REGARDING OUR TV SET COMPATIBILITY WITH THIS
MODEL 525p AND 625p UNIT, PLEASE CONTACT
OUR CUSTOMER SERVICE CENTER.
You have to set the disc format option to [Mastered]
in order to make the discs compatible with the LG
players when formatting rewritable discs. When
setting the option to Live File System, you cannot
use it on LG players.
(Mastered/ Live File System : Disc format system for
Windows Vista)
4. For more detailed information about
disposal of your old appliance,
please contact your city office, waste
disposal service or the shop where
you purchased the product.
LG Electronics hereby declares that this/
these product(s) is/are in compliance
with the essential requirements and
other relevant provisions of Directive
2004/108/EC, 2006/95/EC, and
2009/125/EC.
European representative :
LG Electronics Service Europe B.V.
Veluwezoom 15, 1327 AE Almere, The
Netherlands (Tel : +31–(0)36–547–8888)
TB106-D0F-ADEULL-ENG.indd 3
11. 11. 30
2:16
4
Table of Contents
Table of Contents
1
Getting Started
2
6
6
6
6
7
7
7
7
7
8
9
10
11
Safety Information
Unique Features
– Portable In
– USB Direct Recording
Accessories
Introduction
– Playable Discs
– About the “7” Symbol Display
– Symbols Used in this Manual
– Regional Codes
Playable file Requirement
Remote control
Front panel
Rear panel
2
Connecting
12
12
12
13
13
14
15
15
16
16
16
16
Connecting to speakers
– Attaching the speakers to the unit
System cable Connection
Connections to Your TV
– HDMI OUT Connection
– Component Video Connection
– Video Connection
– Resolution Setting
Video Output Resolution
Optional Equipment Connection
– PORT. IN Connection
– Listening to music from your portable
player or external device
– USB Connection
– OPTICAL IN connection
– AUX In Connection
– Speaker ez setup
– Antenna Connection
– Playing the iPod
– Compatible iPod
17
17
17
18
18
19
20
TB106-D0F-ADEULL-ENG.indd 4
3
System Setting
21
21
21
22
22
23
23
24
Adjust the setup settings
– OSD Initial language settings Optional
– To display and exit the Setup menu
– Language
– Display
– Audio
– Lock (Parental Control)
– Others
4
Operating
25
25
26
26
26
27
27
27
27
27
27
28
28
29
30
30
30
30
31
31
31
31
31
31
31
32
32
32
Using the Home Menu
Basic Operations
Other Operations
– Displaying Disc Information on-screen
– To display the DVD Menu
– To display the DVD title
– 1.5 times speed playback
– Screen Saver
– Starting play from selected time
– Resume playback
– Changing subtitle code page
– Marked Playback
– Viewing a PHOTO file
– Last Scene Memory
– System Select - Optional
– Adjust the speaker level settings
– Setting the Clock
– Using your player as an alarm clock
– Sleep Timer Setting
– Dimmer
– Turn off the sound temporarily
Radio Operations
– Listening to the radio
– Presetting the Radio Stations
– Deleting all the saved stations
– Deleting a saved station
– Improving poor FM reception
– Seeing information about a radio
station
11. 11. 30
2:16
Table of Contents
33
33
33
34
34
Sound adjustment
– Setting the surround mode
– Adjusting the sound
Advanced Operations
– Recording to USB
5
Troubleshooting
35
Troubleshooting
6
Appendix
36
37
38
39
41
41
41
Area Code List
Language code List
Trademarks and Licenses
Specifications
Maintenance
– Handling the Unit
– Notes on Discs
5
1
2
3
4
5
6
TB106-D0F-ADEULL-ENG.indd 5
11. 11. 30
2:16
6
Getting Started
Unique Features
Accessories
Please check and identify the supplied accessories.
1
Portable In
OPEN/
CLOSE
Getting Started
Listens to music from your portable device. (MP3,
Notebook, etc)
RADIO&
INPUT
h
SPEAKER
LEVEL
SOUND
EFFECT
INFO/
DISPLAY
b
TITLE
BACK
TIMER
DISC
MENU
DIMMER
RDS/SET
VOL +
VOL
_
TV
USB Direct Recording
Records music from CD to your USB device.
Remote control (1)
Batteries (2)
FM Antenna (1)
Video Cable (1)
iPod Cradle (1)
Speaker Cables (2)
AC power cable (1)
TB106-D0F-ADEULL-ENG.indd 6
11. 11. 30
2:16
Getting Started
Introduction
Playable Discs
Symbols Used in this Manual
r
DVD-Video, DVD±R/RW in Video
mode or VR mode and finalized
t
Audio CDs
1
y
Video files contained in the
USB/Disc
u
Audio files contained in the
USB/Disc
i
Photo files
Getting Started
This unit plays DVD±R/RW and CD-R/RW that
contains audio titles, DivX, MP3, WMA and/or
JPEG files. Some DVD±RW/DVD±R or CD-RW/
CD-R cannot be played on this unit due to the
recording quality or physical condition of the disc,
or the characteristics of the recording device and
authoring software.
7
DVD-VIDEO (8 cm / 12 cm disc)
Discs such as movies that can be
purchased or rented.
DVD±R (8 cm / 12 cm disc)
Video mode and finalized only.
, Note
Indicates special notes and operating features.
, Tip
Indicates tip and hints for making the task easier.
DVD-RW (8 cm / 12 cm disc)
Video mode and finalized only.
DVD+R: Video mode only
Supports the double layer disc also.
DVD+RW (8 cm / 12 cm disc)
Video mode and finalized only.
Audio CD: Music CDs or CD-R/CDRW in music CD format that can be
purchased.
About the “7” Symbol Display
“7” may appear on your TV display during
operation and indicates that the function explained
in this owner’s manual is not available on that
specific media.
TB106-D0F-ADEULL-ENG.indd 7
> Caution
Indicates cautions for preventing possible damages
from abuse.
Regional Codes
This unit has a regional code printed on the rear of
the unit. This unit can play only DVD discs labeled
same as the rear of the unit or “ALL”.
y Most DVD discs have a globe with one or more
numbers in it clearly visible on the cover. This
number must match your unit’s regional code or
the disc cannot play.
y If you try to play a DVD with a different regional
code from your unit, the message “Check
Regional Code” appears on the TV screen.
11. 11. 30
2:16
8
Getting Started
Playable file
Requirement
DivX file requirement
DivX file compatibility with this unit is limited as
follows:
y Available resolution: within 800 x 600 (W x H)
pixels.
1
Getting Started
MP3/ WMA music file requirement
MP3/ WMA file compatibility with this unit is limited
as follows :
y Sampling frequency : within 32 to 48 kHz (MP3),
within 32 to 48 kHz (WMA)
y Bit rate : within 32 to 320 kbps (MP3),
40 to 192 kbps (WMA)
y Support Version : v2, v7, v8, v9
y Maximum files : Under 999
y File extensions : “.mp3”/ “.wma”
y The file name of the DivX subtitle should be
entered within 45 characters.
y If there is impossible code to express in the
DivX file, it may be displayed as “ _ “ mark on the
display.
y Frame rate : less than 30 fps.
y If the video and audio structure of recorded
files is not interleaved, either video or audio is
outputted.
y Playable DivX file : “.avi”, “.mpg”, “.mpeg”, “.divx”
y We recommend that you use Easy-CD Creator,
which creates an ISO 9660 file system.
y Playable Subtitle format : SubRip (*.srt/ *.txt),
SAMI (*.smi), SubStation Alpha (*.ssa/ *.txt),
MicroDVD (*.sub/ *.txt), SubViewer 2.0 (*.sub/
*.txt), Vobsub (*.sub)
Photo file requirement
y Playable Codec format : “DIVX3.xx”, “DIVX4.xx”,
“DIVX5.xx”, “MP4V3”, “3IVX”.
y CD-ROM file format : ISO9660/JOLIET
Photo file compatibility with this unit is limited as
follows :
y Max pixel in width : 2 760 x 2 048 pixel
y Maximum files : Under 999
y Some discs may not operate due to a different
recording format or the condition of disc.
y File extensions: “.jpg”
y CD-ROM file format : ISO9660/JOLIET
y Playable Audio format : “AC3”, “PCM”, “MP3”, “WMA”.
y Sampling frequency : within 32 to 48 kHz (MP3),
within 32 to 48 kHz (WMA)
y Bit rate : within 32 to 320 kbps (MP3), 40 to 192
kbps (WMA)
y For Discs formatted in Live file system, you can
use not it on this unit.
y If the name of movie file is different from that of
the subtitle file, during playback of a DivX file,
subtitle may not be display.
y If you play a DivX file differ from DivXspec, it may
not operate normally.
TB106-D0F-ADEULL-ENG.indd 8
11. 11. 30
2:16
Getting Started
Remote control
OPEN/
CLOSE
RADIO&
INPUT
• • • • • • a • • • • •
1 (POWER) : Switches the unit
ON or OFF.
B OPEN/CLOSE : Opens and
closes the disc tray.
• • • • • • b • • • • •
h
0-9 numerical buttons: Selects
numbered tracks, files, or preset
number.
CLEAR: Removes a number when
setting the password.
SPEAKER
h REPEAT: Selects a play
mode. (Repeat/ Random)
LEVEL
SOUND
EFFECT
INFO/
DISPLAY
C/V SKIP: Goes to the next
or previous chapter / track / file.
c/v SCAN: Searches
backward or forward.
TIMER
DISC
MENU
DIMMER
RDS/SET
VOL +
VOL
_
TV
• • • • • • e • • • • •
CLOCK : For setting the clock and
checking the time.
?: This button is not available.
• • • • • • c • • • • •
SPEAKER LEVEL: Sets the sound
level of desired speaker.
VOL +/- (Volume): Adjusts speaker
volume.
OPTICAL: Changes input source
to optical directly.
n HOME: Displays the [Home
Menu].
MARKER: Marks play list.
m INFO/DISPLAY: Accesses OnScreen Display.
1
DISC MENU: Accesses the menu
on a DVD disc.
M (PAUSE/STEP) : Pauses
playback.
• • • • • • d • • • • •
TB106-D0F-ADEULL-ENG.indd 9
TITLE: If the current DVD title has
a menu, the title menu appears
on the screen. Otherwise, the disc
menu may not appear.
DIMMER : Adjusts the brightness
of the display window.
MUTE: Mutes the sound.
Remove the battery cover on the
rear of the Remote Control, and
insert two (size AAA) batteries
with 4 and 5 matched correctly.
x BACK: Moves backwards in
the menu or exits the setup menu.
MONO/STEREO: Selects Mono/
Stereo.
SOUND EFFECT: Selects a sound
effect mode.
Battery Installation
b ENTER: Acknowledges menu
selection.
Presetting the radio stations.
d (PLAY) : Starts playback.
Z (STOP): Stops playback.
TITLE
PRESET +/-: Selects programme
of Radio.
TIMER : With the TIMER function
you can turn USB, CD play and
TUNER reception on or off at a
desired time.
b
BACK
TUNING -/+: Tunes in the desired
radio station.
Getting Started
P RADIO&INPUT: Changes
input sources.
9
RDS/SET : RDS (Radio Data
System). (Refer to page 32)/
Confirms the setting.
PTY : Searches radio stations by
radio type.
SLEEP: Sets the System to turn off
automatically at a specified time.
X REC: USB Direct Recording.
• • • • • • f • • • • •
TV Control buttons: Controls the
TV. (LG TV only)
You can control the sound level,
input source, and power switching
of LG TVs as well.
Hold 1 (POWER) and press
PR/CH (W/S) button repeatedly
until the TV turns on or off.
W/S/A/D (up/ down/ left/
right): Used to navigate on-screen
displays.
11. 11. 30
2:16
10
Getting Started
Front panel
1
a
b
c
d
e
Getting Started
1/!
f
B
d/M
Z
FUNC.
C
V
PORT. IN
g
h
i
j
<
- BASS +
a 1/! (POWER)
Switches the unit ON or OFF.
b Disc tray
c Display window
Shows the current status of the unit.
d PORT. IN
Connects to a portable player with audio
outputs.
e B (OPEN/CLOSE)
Opens and closes the disc tray.
d/M (PLAY / PAUSE)
Starts playback.
Pauses playback temporarily, press again to exit
pause mode.
TB106-D0F-ADEULL-ENG.indd 10
- TREBLE +
- VOLUME +
Z (STOP)
Stops playback.
FUNC. (FUNCTION)
Changes the input source or function.
C/V (Skip/Search):
Goes to next or previous file/track.
Searches backward or forward (Press and hold)
Tunes in the desired radio station.
f USB Port
Connects an USB device.
g BASS -/+
h VOLUME -/+
Adjusts speaker volume.
i TREBLE -/+
j <
Headphone jack
11. 11. 30
2:16
Getting Started
11
Rear panel
1
c
HDMI OUT
Pr/Cr
d
g
iPod DOCK
L
R
Y
COMPONENT VIDEO OUT
(PROGRESSIVE SCAN)
b
h
VIDEO OUT
Pb/Cb
CABLE
Getting Started
a
AUX IN
OPTICAL IN
e
FM
ANTENNA
f
SPEAKERS
L
4
POWER IN
5
CABLE
R
i
j
a CABLE
b HDMI OUT
Connects to TV with HDMI inputs.
(Interface for digital audio and video)
k
f iPod DOCK
Connect to the furnished iPod cradle.
g AUX IN
h ANTENNA (FM)
c COMPONENT VIDEO (Y Pb Pr)
OUT(PROGRESSIVE SCAN)
Connects to a TV with Y Pb Pr inputs.
i SPEAKERS
Connects the speaker cables.
d VIDEO OUT
Connects to a TV with video inputs.
k POWER IN
j CABLE
e OPTICAL IN
Connects to optical audio equipment.
TB106-D0F-ADEULL-ENG.indd 11
11. 11. 30
2:16
12
2
Connecting
Connecting to
speakers
System cable
Connection
Attaching the speakers to the
unit
Your unit consists of two separate parts, DVD
player/Tuner and Amplifier/power.
Before you can use your unit, the separate parts
must be connected with the system connection
cable.
1. Loosen the knob by turning it counterclockwise.
Connecting
2. Insert the bare part of the wire into the hole in
side of each terminal.
VIDEO OUT
HDMI OUT
3. Tighten the knob by turning it clockwise to
secure the wire.
Connect the red stripe of each wire to the terminals
marked + (plus) and the other end to the terminals
marked - (minus).
Pr/Cr
iPod DOCK
L
Pb/Cb
R
Y
CABLE
COMPONENT VIDEO OUT
(PROGRESSIVE SCAN)
OPTICAL IN
AUX IN
FM
ANTENNA
SPEAKERS
L
4
POWER IN
5
CABLE
R
, Note
> Caution
To operate the unit normally, you should push
the system cable fully enough to let it reach
end of cable connector of the DVD Player.
The speakers contain magnet parts, so color
irregularity may occur on the TV screen or PC
monitor screen. Please use the speakers far
away from either TV screen or PC monitor.
TB106-D0F-ADEULL-ENG.indd 12
11. 11. 30
2:16
Connecting
Connections to Your
TV
Make one of the following connections, depending
on the capabilities of your existing equipment.
, Note
HDMI OUT Connection
If you have a HDMI TV or monitor, you can connect
it to this unit using a HDMI cable (Type A, High
Speed HDMI™ cable).
Connect the HDMI OUT jack on the unit to the
HDMI IN jack on a HDMI compatible TV or monitor.
Set the TV’s source to HDMI (refer to TV’s Owner’s
manual).
y Depending on your TV and other
equipment you wish to connect, there are
various ways you could connect the player.
Use only one of the connections described
in this manual.
2
Unit
Connecting
y Please refer to the manuals of your TV,
Stereo System or other devices as necessary
to make the best connections.
13
VIDEO OUT
HDMI OUT
Pr/Cr
iPod DOCK
L
Pb/Cb
R
Y
CABLE
COMPONENT VIDEO OUT
(PROGRESSIVE SCAN)
OPTICAL IN
FM
AUX IN
ANTENNA
SPEAKERS
HDMI OUT
L
4
POWER IN
5
CABLE
R
> Caution
y Make sure the unit is connected directly
to the TV. Tune the TV to the correct video
input channel
Not supplied
y Do not connect your player via your VCR.
The image could be distorted by the copy
protection system.
TV
, Tip
y You can fully enjoy digital audio and video
signals together with this HDMI connection.
y When you use HDMI connection, you can
change the resolution for the HDMI output.
(Refer to “Resolution” on page 15.)
TB106-D0F-ADEULL-ENG.indd 13
11. 11. 30
2:16
14
Connecting
, Note
y If a connected HDMI device does not accept
the audio output of the unit, the HDMI
device’s audio sound may be distorted or
may not output.
2
Connecting
y When you connect a HDMI or DVI
compatible device make sure of the
following:
- Try switching off the HDMI/DVI device and
this unit. Next, switch on the HDMI/DVI
device and leave it for around 30 seconds,
then switch on this unit.
Component Video Connection
Connect the COMPONENT VIDEO OUT
(PROGRESSIVE SCAN) jacks on the unit to the
corresponding input jacks on the TV using
component cables.
You can hear the sound through the system’s
speakers.
- The connected device’s video input is set
correctly for this unit.
Pr/Cr
VIDEO OUT
Pr/Cr
- The connected device is compatible with
720 x 480i (or 576i), 720 x 480p (or 576p),
1280 x 720p, 1920 x 1080i or 1920 x 1080p
video input.
iPod DOCK
L
Pb/Cb
R
Y
COMPONENT VIDEO OUT
(PROGRESSIVE SCAN)
Pb/Cb
OPTICAL IN
AUX IN
Y
COMPONENT VIDEO OUT
(PROGRESSIVE SCAN)
Not
supplied
POWER IN
y Not all HDCP-compatible HDMI or DVI
devices will work with this unit.
- The picture will not be displayed properly
with non-HDCP device.
FM
ANTENNA
Unit
- This unit does not playback and TV screen
is changed to black or green screen or the
snow noise may occur on the screen.
y If there is noise or lines on the screen, please
check the HDMI cable and usea higher
version cable than High Speed HDMI™
cable.
TV
Green
Blue
Red
> Caution
y Changing the resolution when the
connection has already been established
may result in malfunctions. To solve the
problem, turn off the unit and then turn it
on again.
y When the HDMI connection with HDCP is
not verified, TV screen is changed to black
or green screen or the snow noise may
occur on the screen. In this case, check the
the HDMI connection, or disconnect the
HDMI cable.
TB106-D0F-ADEULL-ENG.indd 14
11. 11. 30
2:16
Connecting
15
Video Connection
Resolution Setting
Connect the VIDEO OUT jack on the unit to the
video in jack on the TV using a video cable.
The unit provides several output resolutions for
HDMI OUT and COMPONENT VIDEO OUT jacks. You
can change the resolution using [Setup] menu.
You can hear the sound through the system’s
speakers.
1. Press n HOME.
2. Use A/D to select the [Setup] and press
b ENTER. The [Setup] menu appears.
Unit
2
VIDEO OUT
Pr/Cr
iPod DOCK
L
Pb/Cb
R
Y
COMPONENT VIDEO OUT
(PROGRESSIVE SCAN)
Connecting
UT
OPTICAL IN
AUX IN
FM
ANTENNA
POWER IN
3. Use W/S to select [Display] option then press
D to move to the second level.
4. Use W/S to select the [Resolution] option
then press D to move to the third level.
TV
5. Use W/S to select the desired resolution then
press b ENTER to confirm your selection.
Yellow
, Note
If your TV does not accept the resolution you
have set on the player, you can set resolution
to 480p (or 576p) as follows:
Press Z (STOP) for more than 5 seconds.
TB106-D0F-ADEULL-ENG.indd 15
11. 11. 30
2:16
16
2
Connecting
Video Output
Resolution
Optional Equipment
Connection
Displayed resolution in display window and
outputted resolution may different according to
connection type.
PORT. IN Connection
[HDMI OUT]: 1080p, 1080i, 720p and 480p (or 576p)
and 480i (or 576i)
Connect an output of portable device (MP3 or PMP
etc) to the PORT. IN input connector. The portable
cable is not supplied as an accessory.
Connecting
[COMPONENT VIDEO OUT]: 480p (or 576p) and 480i
(or 576i)
[VIDEO OUT]: 480i (or 576i)
Not supplied
B
d/M
FUNC.
C
PORT. IN
Z
V
PORT. IN
1
<
- TREBLE +
MP3 player, etc...
Listening to music from your
portable player or external
device
The unit can be used to play the music from many
types of portable player or external devices.
1. Connect the portable player to the
PORT. IN(PORTABLE IN) connector of the unit.
Or
Connect the external device to the AUX IN
connector of the unit.
2. Turn the power on by pressing 1 (POWER).
3. Select the PORTABLE function or AUX function
by pressing P RADIO&INPUT on the remote
control or FUNC. on the unit.
4. Turn on the portable player or external device
and start it playing.
TB106-D0F-ADEULL-ENG.indd 16
11. 11. 30
2:16
Connecting
17
USB Connection
OPTICAL IN connection
Connect the USB port of USB Memory (or MP3
player, etc.) to the USB port on the front of the unit.
Connect an optical output of Unit (or Digital Device
etc) to the OPTICAL IN connector.
B
d/M
Z
FUNC.
C
V
VIDEO OUT
Pr/Cr
HDMI OUT
iPod DOCK
L
Pb/Cb
PORT. IN
R
Y
COMPONENT VIDEO OUT
(PROGRESSIVE SCAN)
AUX IN
OPTICAL IN
FM
ANTENNA
2
Connecting
<
POWER IN
VOLUME
OPTICAL IN
Removing the USB Device from the unit
1. Choose a different function mode or press
Z (STOP) twice in a row.
2. Remove the USB device from the unit.
You can only recharge your iPod through USB
port. To listen to music on iPod, refer to the page
19.
To the digital
optical output jack of
your component
Not
supplied
Compatible USB Devices
y MP3 Player : Flash type MP3 player.
y USB Flash Drive : Devices that support USB2.0 or
USB1.1.
y The USB function of this unit does not support
some USB devices.
AUX In Connection
Connect an Output of auxiliary device to the AUX
(L/R) INPUT Connector.
AUX IN
USB device requirement
Unit
VIDEO OUT
L
iPod DOCK
L
y Devices which require additional program
installation connected to a computer, are not
supported.
R
OPTICAL IN
AUX IN
FM
ANTENNA
R
Not supplied
POWER IN
y Do not extract the USB device while in operation.
y For a large capacity USB, it may take longer than
a few minute to be searched.
y To prevent data loss, back up all data.
To the audio output
jacks of your component
(TV, VCR, etc.)
y If you use a USB extension cable or USB hub, the
USB device is not recognized.
y Using NTFS file system is not supported. (Only
FAT(16/32) file system is supported.)
y This unit is not supported when the total
number of files is 1 000 or more.
y External HDD, Card readers, Locked devices,
or hard type usb devices are not supported.
Red
White
, Note
If your TV has only one output for audio
(mono), connect it to the left (white) audio jack
on the unit.
y USB port of the unit cannot be connected to PC.
The unit can not be used as a storage device.
TB106-D0F-ADEULL-ENG.indd 17
11. 11. 30
2:16
18
Connecting
Speaker ez setup
Antenna Connection
Listen to sound from TV, DVD and Digital Device
with 2ch mode. Even in power off mode, if you
press OPTICAL, then power is on and automatically
changed to AUX OPT mode.
Connect the supplied FM antenna for listening to
the radio.
Connect the FM Wire antenna to the FM antenna
connector.
1. Connect the unit’s OPTICAL IN jack to jack on
optical out of your TV (or Digital Device etc.).
2
2. Select the AUX OPT by using the OPTICAL.
To select the AUX OPT directly.
Connecting
3. Listen to sound with 2ch speaker.
4. To escape from AUX OPT by using the OPTICAL.
Function is retuned to previous one.
FM
ANTENNA
VIDEO OUT
Pr/Cr
iPod DOCK
L
Pb/Cb
R
Y
COMPONENT VIDEO OUT
(PROGRESSIVE SCAN)
OPTICAL IN
AUX IN
FM
ANTENNA
POWER IN
, Note
After connecting, stretch the opposite side
of the cable to any direction where it is able
to receive incoming radio broadcast from
outside. There may be a various way of
stretching it.
TB106-D0F-ADEULL-ENG.indd 18
11. 11. 30
2:16
System Setting
Playing the iPod
You can enjoy the sound with your iPod. For details
about iPod, refer to the iPod User Guide.
1. Connect the iPod cradle.
2. Connect the iPod firmly.
VIDEO OUT
HDMI OUT
Pr/Cr
iPod DOCK
OPTICAL IN
AUX IN
A
SPEAKERS
L
4
ON UNIT
ON REMOTE
Pauses or
restart
d/M
d/M
Skip
C/V
C/V
Search
Press and hold
C/V
Press and hold
c/v
Move to the
previous
menu
-
A
Move to the
desired item
-
W/S
Chooses a
item
-
D
R
Y
COMPONENT VIDEO OUT
(PROGRESSIVE SCAN)
Do this
L
Pb/Cb
CABLE
To
19
5
CABLE
3
R
System Setting
If you turn this unit on, your iPod is
automatically turned on and recharging starts.
3. Press FUNC. on the unit or P RADIO&INPUT
on the remote control to select iPod function.
You can operate your iPod through an iPod’s
display by using the supplied remote control
and also control on your iPod.
, Note
y With iPod cradle connected to iPod
DOCK, you can also connect TV to VIDEO
OUT(Refer to page 15).
y You can control through both the TV and
iPod or iPhone in order to play music
files, and watch movie clips, and look at
the picutures which are saved to iPod or
iPhone.
y Be sure to use the video connection
through the VIDEO OUT jack on the rear
panel of this unit. Select the appropriate
video input mode on the TV.
TB106-D0F-ADEULL-ENG.indd 19
11. 11. 30
2:16
20 Connecting
Compatible iPod
y We recommend installing the latest software
version.
2
y The unit supports the models as follows/ iPod
nano 1 G, 2 G, 3 G, 4 G, 5 G, 6 G/
iPod classic/ iPod 5 G/
iPod touch 2 G, 3 G, 4 G/ iPhone 3 G, 3GS, 4.
For some models, the unit may not operate
depending on the firmware version.
Connecting
y Depending on your iPod’s software version, you
may not control your iPod from the player.
, Note
y If this unit displays an error message, follow
the message. An error message “ERROR”.
- Your iPod is not connected firmly.
- This unit recognizes your iPod as an
unknown device.
- Your iPod is exceptionally low in power.
/ The battery needs to be charged.
/ If you charge the battery while iPod
is extremely low in power, it may take
longer to be charged.
y iPod does not support recording function
when connected.
y Depending on your iPod’s software version,
it may not be possible to control your iPod
from this unit. We recommend installing the
latest software version.
y If you use an application, make a call, or
send and receive SMS text message, etc. on
iPod touch or iPhone, disconnect it from
iPod dock of this unit and then use it.
y If you have a problem with your iPod, please
visit www.apple.com/support/ipod.
TB106-D0F-ADEULL-ENG.indd 20
11. 11. 30
2:16
System Setting
Adjust the setup
settings
By using the Setup menu, you can make various
adjustments to items such as picture and sound.
21
To display and exit the Setup
menu
1. Press n HOME.
Displays the [Home Menu].
You can also set a language for the subtitles and
the Setup menu, among other things. For details on
each Setup menu item, see pages 21 to 24.
2. Select an [Setup] by using A D.
OSD Initial language settings
- Optional
1. Press 1 (POWER) to turn the unit on. The
language setup menu will appear on the screen.
4. Press n HOME or x BACK to exit in the
[Setup] Menu.
About help menu for Setup
Menu
Buttons
Operation
WS
Moving to another
menu.
a
Move
A
Moving to previous
level.
d
Move
D
Moving to next
level or selecting
menu.
x BACK
To exit the [Setup]
menu.
b ENTER
To confirm menu.
ws
Move
x
2. Use WSAD to select a language then press
b ENTER.
The confirm menu will appear.
Close
b
Select
3
System Setting
During the first use of this unit, the initial language
setup menu appears on your TV screen. You must
complete initial language selection before using
the unit. English will be selected as the initial
language.
3. Press b ENTER.
Displays the [Setup].
3. Use AD to select the [Enter] then press
b ENTER to finish the language setup.
TB106-D0F-ADEULL-ENG.indd 21
11. 11. 30
2:16
22 System Setting
Language
Display Mode
Menu Language
The Display Mode setting works only when the TV
Aspect mode is set to 4:3.
Select a language for the Setup menu and then on
screen display.
[Letterbox]
Disc Audio / Disc Subtitle / Disc
Menu
[Panscan]
Select the language you prefer for the audio track
(disc audio), subtitles, and the disc menu.
[Original]
3
Refers to the original language in which the
disc was recorded.
System Setting
[Other]
To select another language, press numeric
buttons and then b ENTER to enter the
corresponding 4-digit number according to
the language code list on the page 37. If you
enter the wrong language code, press CLEAR.
[Off (for Disc Subtitle)]
Turn off Subtitle.
Display
Displays a wide picture with bands on the
upper and lower portions of the screen.
Automatically displays the wide picture on the
entire screen and cuts off the portions that do
not fit. (If the disc/file is not compatible with
Pan Scan, the picture is displayed at Letterbox
ratio.)
Resolution
Sets the output resolution of the Component and
HDMI video signal. Refer to “Resolution Setting” for
details about the resolution (page 15).
[Auto]
If the HDMI OUT jack is connected to
TVs providing display information (EDID),
automatically selects the resolution best suited
to the connected TV. If the COMPONENT
VIDEO OUT is only connected, this changes the
resolution to 480i (or 576i) as default resolution.
[1080p]
TV Aspect
Outputs 1080 lines of progressive video.
Select which screen aspect to use based on the
shape of your TV screen.
[1080i]
[4:3]
Select when a standard 4:3 TV is connected.
[16:9]
Select when a 16:9 wide TV is connected.
Outputs 1080 lines of interlaced video.
[720p]
Outputs 720 lines of progressive video.
[480p (or 576p)]
Outputs 480 (or 576) lines of progressive video.
[480i (or 576i)]
Outputs 480 (or (576) lines of interlaced video.
TB106-D0F-ADEULL-ENG.indd 22
11. 11. 30
2:16
System Setting 23
Audio
Lock (Parental Control)
DRC (Dynamic Range Control)
Initial Setting the Area Code:
Make the sound clear when the volume is turned
down (Dolby Digital only). Set to [On] for this effect.
When you use this unit for the first time, you have
to set the Area Code.
1. Select the [Lock] menu and then press D.
Vocal
Select [On] to mix karaoke channels into normal
stereo.
This function is effective for multi-channel karaoke
DVDs only.
HD AV Sync
3. Select the first character using WS buttons.
4. Press b ENTER and select the second character
using WS buttons.
5. Press b ENTER to confirm your Area code
selection.
Rating
Blocks playback of rated DVDs based on their
contents. Not all discs are rated.
3
System Setting
Sometimes Digital TV encounters a delay between
picture and sound. If this happens you can
compensate by setting a delay on the sound so
that it effectively ‘waits’ for the picture to arrive:
this is called HD AV Sync. Use WS (on the remote
control) to scroll up and down through the delay
amount, which you can set at anything between 0
and 300m/sec.
2. Press D.
To access the [Lock] options, you must input the
password you have created. Input a password
and press b ENTER. Enter it again and press
b ENTER to verify. If you make a mistake before
pressing b ENTER, press CLEAR.
1. Select [Rating] on the [Lock] menu then press
D.
2. Input a password and press b ENTER.
3. Select a rating from 1 to 8 using the WS
buttons.
[Rating 1-8]
Rating one (1) has the most restrictions and
rating eight (8) is the least restrictive.
[Unlock]
If you select unlock, parental control is not
active and the disc plays in full.
4. Press b ENTER to confirm your rating selection.
TB106-D0F-ADEULL-ENG.indd 23
11. 11. 30
2:16
24 System Setting
Password
Others
You can enter or change password.
1. Select [Password] on the [Lock] menu and then
press D.
2. Press b ENTER.
3. Input a password and press b ENTER.
To change the password, press b ENTER when
the [Change] option is highlighted. Input a
password and press b ENTER. Enter it again
and press b ENTER to verify.
4. Press n HOME to exit the menu.
,
3
Note
If you forget your password, you can clear it
using the following steps:
System Setting
1. Select the [Setup] menu on the [Home
Menu].
DivX VOD
We provide you with the DivX® VOD (Video On
Demand) registration code that allows you to rent
and purchase videos using the DivX® VOD service.
For more information, visit www.divx.com/vod.
[Register]
Displays the registration code of your player.
[Deregister]
Deactivate your player and display the
deactivation code.
, Note
All the downloaded videos from DivX VOD can
only be played back on this unit.
2. Input the 6-digit number “210499” and
press b ENTER. The password is cleared.
Area Code
Enter the code of the area whose standards were
used to rate the DVD video disc, based on the list
on page 36.
1. Select [Area Code] on the [Lock] menu then
press D.
2. Input a password and press b ENTER.
3. Select the first character using WS buttons.
4. Press b ENTER and select the second character
using WS buttons.
5. Press b ENTER to confirm your Area code
selection.
TB106-D0F-ADEULL-ENG.indd 24
11. 11. 30
2:16
Operating 25
Using the Home Menu
Basic Operations
1. Press n HOME.
Displays the [Home Menu].
1. Insert the disc by using the B OPEN/CLOSE or
Connect the USB device to the USB port.
2. Press n HOME.
Displays the [Home Menu].
2. Select an option by using AD.
3. Press b ENTER then selected option menu.
3. Select an option by using AD.
If you select the [Movie], [Photo] or [Music]
option when you connect up to two devices,
it appears as belows. Select a media then press
b ENTER.
[Music] – Displays [MUSIC] menu.
[Movie] – Start video media’s playback or displays
the [MOVIE] menu.
[Photo] – Displays [PHOTO] menu.
[Setup] – Displays the [Setup] menu.
, Note
, Note
y For the most Audio CD and DVD-ROM discs,
playback starts automatically.
y The unit plays only music file contained in
the USB storage device or disc automatically.
To
Stop
Playback
Pause
4
Operating
You can not select the [Music], [Movie] or
[Photo] option when the USB device is not
connected or a disc is not inserted.
4. Press b ENTER then selected option menu.
Do this
Press Z (STOP).
Press d (PLAY), MONO/
STEREO.
Press M (PAUSE/STEP).
Press M (PAUSE/STEP)
Frame-byrepeatedly to play title FrameFrame playback
by-Frame. (DVD, DivX only)
During playback, press
C/V SKIP to go to the
Skipping to the next chapter/ track/ file or to
next/ previous return to the beginning of the
chapter/ track/ current chapter/ track/ file.
file
Press C SKIP twice briefly
to step back to the previous
chapter/ track/ file.
Locating a
point quickly by
playing a file in
fast forward or
fast reverse
TB106-D0F-ADEULL-ENG.indd 25
During playback, press
c/v SCAN repeatedly to
select the required scan speed.
To return to normal speed,
press d (PLAY), MONO/
STEREO.
11. 11. 30
2:16
26 Operating
To
Playing
repeatedly or
randomly
Do this
Press h REPEAT repeatedly,
and the current title, chapter
or track will be played back
repeatedly or randomly.
- DVD : Chapter/ Title/ Off
- DivX : Title/ All/ Off
- Audio CD/ MP3/ WMA : Track/
All/ Random/ Off
Slowing down
the playing
speed
In the pause mode, press
c/v SCAN to select the
required speed. (DVD, DivX
only) The DivX file cannot be
slow down reverse playback.
Other Operations
Displaying Disc Information
on-screen
You can display various information about the disc
loaded on-screen.
1. Press m INFO/DISPLAY to show various
playback information.
The displayed items differ depending on the
disc type or playing status.
2. You can select an item by pressing WS and
change or select the setting by pressing AD.
Title – Current title number/ total number of titles.
Chapter – Current chapter number/ total number
of chapters.
Time – Elapsed playing time.
4
Audio – Selected audio language or channel.
Operating
Subtitle – Selected subtitle.
Angle – Selected angle/ total number of angles.
, Note
If any button is not pressed for a few seconds,
the on-screen display disappears.
To display the DVD Menu
r
When you play a DVD which contains several menu,
you can select the menu you want using the Menu.
1. Press DISC MENU.
The disc’s menu appears.
2. Select the menu by using WSAD.
3. Press d (PLAY), MONO/STEREO to confirm.
TB106-D0F-ADEULL-ENG.indd 26
11. 11. 30
2:16
Operating 27
To display the DVD title
Resume playback
r
ryut
When you play a DVD which contains several title,
you can select the title you want using the Menu.
The unit records the point where you pressed the
Z (STOP) depending on the disc.
If “MZ (Resume Stop)” appears on the screen
briefly, press d (PLAY), MONO/STEREO to resume
playback (from the scene point).
1. Press TITLE.
The disc’s title appears.
2. Select the menu by pressing WSAD.
3. Press d (PLAY), MONO/STEREO to confirm.
1.5 times speed playback
r
The 1.5 speed allows you to watch the pictures and
listen to the sound quicker than playing at a normal
speed.
If you press Z (STOP) twice or unload the disc,
“Z”(Complete Stop) appears on the screen. The
unit will clear the stopped point.
, Note
The resume point may be cleared when a
button is pressed (for example; 1 (POWER),
B (OPEN/CLOSE), etc).
1. During playback, press d (PLAY), MONO/
STEREO to play at 1.5 times speed. “dX1.5”
appears on the screen.
Changing subtitle code page
2. Press d (PLAY), MONO/STEREO again to exit.
y
The screen saver appears when you leave the unit
in Stop mode for about five minutes.
Starting play from selected
time
1. During playback, press m INFO/DISPLAY to
display the On-Screen display.
Operating
Screen Saver
4
If the subtitle is not displayed properly, you can
change the subtitle code page to view the subtitle
file properly.
2. Use WS to select the [Code Page] option.
3. Use AD to select desired code option.
4. Press x BACK to exit the On-Screen display.
ry
To start playing at any chosen time on the file or
title.
1. Press m INFO/DISPLAY during playback.
2. Press WS to select the time clock icon and
“--:--:--” appears.
3. Input the required start time in hours, minutes,
and seconds from left to right. If you enter the
wrong numbers, press CLEAR to remove the
numbers you entered. Then input the correct
numbers.
For example, to find a scene at 1 hour, 10
minutes, and 20 seconds, enter “11020” by using
numerical buttons.
4. Press b ENTER to confirm. Playback starts from
the selected time.
TB106-D0F-ADEULL-ENG.indd 27
11. 11. 30
2:16
28 Operating
Marked Playback
To delete a Marker
ut
1. Use WS to select the track that you wish to erase
from the marked file.
The mark function enables you to store your
favourite files from any disc or USB device in the
unit memory.
2. Press MARKER.
1. Select [Music] on the [Home Menu].
To delete all Markers
Returning to the upper folder.
(MP3/ WMA only)
File information will be displayed
according to the ID3TAG information
on the appropriate music file. (MP3
only)
Use WSAD to select [Deselect All] then press
b ENTER in program edit mode.
, Note
The markers are also cleared when the disc or
USB device is removed, the unit is switched to
power off or the function is switched to others.
Viewing a PHOTO file
i
This unit can play discs with photo files.
4
Operating
1. Select [Photo] on the [Home Menu] and press
b ENTER.
Selecting all tracks/ files.
Deselecting all tracks/files.
Moving to the previous or
next file list.
Moving to the previous or
next file list.
2. Select a desired music on the [List] by using the
WS then press MARKER to appears the mark on
the list.
3. Press b ENTER or d (PLAY), MONO/STEREO.
Displays the play mode.
4. Select the play mode by using the WS and press
b ENTER.
Returning to the upper
folder.
[Mark Play]
Marked playback.
[Current Play]
Normal playback.
, Note
2. Press WS to select a folder, and then press
b ENTER.
3. If you want to view a slide show, press WS to
highlight a file and press d (PLAY), MONO/
STEREO.
If you want to select all files on the list, select
[Select All] and press b ENTER.
TB106-D0F-ADEULL-ENG.indd 28
11. 11. 30
2:16
Operating 29
About help menu in the [Photo] menu
Menu
Buttons
d Slide
Show
d (PLAY),
MONO/
STEREO
Operation
Viewing a slide
show.
wsad
Move
WSAD
Moving to another
file or content.
b
Select
b ENTER
Viewing a particular
file.
x
Close
x BACK
Returning to the
[Home Menu].
About help menu in the full screen
Menu
Buttons
Operation
Menu
m
INFO/
DISPLAY
Displaying the Option
menu.
a/d
Prev./ Next
A/D
Moving to another file.
x BACK
Returning to the
[Photo] menu.
You can use various options during viewing a
photo in full screen.
1. While viewing a photo in full screen, press
m INFO/DISPLAY to display the option menu.
2. Select an option using WSAD.
a
b
c
d
e
a Current photo/ Total number of photos –
Use AD to view previous/next photo.
b Slide Show z/M– Press b ENTER to start
or pause slide show.
c Speed x3/ x2/ x1 – Use b ENTER to select
a delaying speed between photos in a slide
show.
4
Operating
x
Close
Options while viewing a photo
d Rotate – Press b ENTER to rotate the photo.
e Go to list – Press b ENTER to return [Photo]
menu.
Last Scene Memory
r
This unit memorizes last scene from the last disc
that is viewed. The last scene remains in memory
even if you remove the disc from the unit or switch
off the unit. If you load a disc that has the scene
memorized, the scene is automatically recalled.
TB106-D0F-ADEULL-ENG.indd 29
11. 11. 30
2:16
30 Operating
System Select - Optional
You must select the appropriate system mode for
your TV system. Press and hold M (PAUSE/STEP)
for more than five seconds to be able to select a
system in the [Home Menu].
, Note
If the USB device is connected or a disc is
inserted, this function is not operated.
Adjust the speaker level
settings
You can adjust the sound level of each speaker.
1. Press SPEAKER LEVEL repeatedly to select a
desired speaker to set.
4
2. Press VOL +/- to adjust the sound level of the
selected speaker while the level setting memu
is displayed on the display window.
Operating
3. Repeat and adjust the sound level of the other
speakers.
Setting the Clock
1. Turn the unit on.
2. Press CLOCK for at least 2 seconds.
3. Choose time mode by pressing C/V.
- AM 12:00 (for an AM and PM display) or 0:00
(for a 24 hour display)
4. Press RDS/SET to confirm your selection.
Using your player as an alarm
clock
1. Turn the unit on.
2. Press TIMER. Each functions flashes.
3. Press RDS/SET when the function you want to
be woken by is showing.
4. “ON TIME” will be displayed. This is your desired
time to unit turns on. Press C/V to
change the hours and minutes and press RDS/
SET to save.
5. The “OFF TIME” will be displayed. This is your
desired time to unit turns off.
6. Press C/V to change the hours and
minutes and press RDS/SET to save.
7. Press C/V to change the volume and
press RDS/SET to save. The clock icon “(“
shows that the alarm is set.
8. Press TIMER button 2 times. You can check the
setting status.
, Note
y If you set the clock time, you can check the
time by pressing CLOCK even when the
player is turned off.
y If you set the clock time and alarm, you
can check the alarm icon “(“ by pressing
CLOCK even when the player is turned off.
y If you set the clock time and alarm, you
can check the alarm icon “(“ and setting
informaiton by pressing TIMER even when
the unit is turned off.
5. Select the hours by pressing C/V.
6. Press RDS/SET.
7. Select the minutes by pressing C/V.
8. Press RDS/SET.
TB106-D0F-ADEULL-ENG.indd 30
11. 11. 30
2:16
Operating
31
Sleep Timer Setting
Radio Operations
Press SLEEP one or more times to select delay time
between 10 and 180 minutes, after the unit will
turn off. (The delay time periods to select are as
follows: 180 -> 150 -> 120 -> 90 -> 80 -> 70 -> 60
-> 50 -> 40 -> 30 -> 20 -> 10)
Be sure that both FM aerials are connected. (Refer
to the page 18.)
To check the remaining time, press SLEEP.
Listening to the radio
To cancel the sleep function, press SLEEP
repeatedly until “SLEEP 10” appears, and then press
SLEEP once again while “SLEEP 10” is displayed.
1. Press P RADIO&INPUT until FM appears in
the display window.
The last received station is tuned in.
, Note
y You can check the remaining time before
the unit turns off.
y Press SLEEP The remaining time appears in
the display window.
y Sleep function will be working after dimmer.
2. Press and hold TUNING -/+ for about two
seconds until the frequency indication starts to
change, then release. Scanning stops when the
unit tunes in a station.
Or
Press TUNING -/+ repeatedly.
3. Adjust the volume by rotating VOLUME on
the front panel or by pressing VOL +/- on the
remote control repeatedly.
Dimmer
Turn off the sound temporarily
Press
MUTE to mute your unit.
You can mute your unit, for example, to answer the
telephone, the “MUTE“ is displayed in the display
window.
Presetting the Radio Stations
You can preset 50 stations for FM.
Before tuning, make sure that you have turned
down the volume.
Operating
Press SLEEP once. The display window will be
darken by half. To cancel it, press SLEEP repeatedly
until dim off.
4
1. Press P RADIO&INPUT until FM appears in
the display window.
2. Select the desired frequency by using TUNING
-/+.
3. Press b ENTER. A preset number will flash in
the display window.
4. Press PRESET +/- to select the preset number
you want.
5. Press b ENTER. The station is stored.
6. Repeat the steps 2 to 5 to store other stations.
Deleting all the saved stations
1. Press and hold CLEAR for two seconds.
“ERASE ALL” will flash up on the unit display.
2. Press CLEAR to erase all saved of the radio
stations.
TB106-D0F-ADEULL-ENG.indd 31
11. 11. 30
2:16
32 Operating
Deleting a saved station
1. Press PRESET +/- to Select a preset number you
want to delete.
2. Press CLEAR, the preset number will blink in the
display window.
3. Press CLEAR again, to delete the selectd preset
number.
Improving poor FM reception
Press d (PLAY), MONO/STEREO on the remote
control. This will change the tuner from stereo to
mono and usually improve the reception.
Seeing information about a
radio station
The FM tuner is supplied with the RDS (Radio Data
System) facility. This shows information about the
radio station being listened to. Press RDS/SET
repeatedly to cycle through the various data types.
PS
The name of the channel will
(Programme
appear in the display.
Service Name)
PTY
(Programme
Type
Recognition)
RT
(Radio Text)
4
Operating
CT
(Time
controlled by
the channel)
The programme type (e.g. Jazz
or News) will appear in the
display.
A text message contains special
information from the broadcast
station. This text may scroll
across the display.
This shows the time and date as
broadcast by the station.
You can search the radio stations by programme
type by pressing RDS/SET. The display will show
the last PTY in use. Press PTY one or more times to
select your preferred programme type. Press AD.
The tuner will search automatically, when a station
is found the search will stop.
TB106-D0F-ADEULL-ENG.indd 32
11. 11. 30
2:16
Operating 33
Sound adjustment
Adjusting the sound
You can adjust the BASS and TREBLE by rotating
BASS or TREBLE.
Setting the surround mode
This system has a number of pre-set surround
sound fields. You can select a desired sound mode
by using SOUND EFFECT.
You can change the SOUND EFFECT using A D
arrow key while the sound effect information is
displayed on.
The displayed items for the equalizer may be
different depending on sound sources and regions.
On Display
Description
You can enjoy comfortable
and natural sound.
Local
specialization
equalizer
Regionally optimized sound
effect. (FORRO/ FUNK/
SERTANEJO/ DANGDUT/
ARABIC/ PERSIAN/ INDIA/
REGUETON/ MERENGUE/
SAMBA/ SALSA/ CUMBIA/
AFRO)
POP
CLASSIC
JAZZ
ROCK
4
Operating
NATURAL
This program lends an
enthusiastic atmosphere to
the sound, giving you the
feeling you are at an actual
rock, pop, jazz or classic
concert.
MP3 -- OPT
This function is optimized for
compressible MP3, WMA file. It
improves the treble sound.
BASS BLAST
During playback, reinforce
the treble, bass and surround
sound effect.
VIRTUAL
You can enjoy more virtual
surround sound.
BYPASS
You can enjoy the sound
without equalizer effect.
TB106-D0F-ADEULL-ENG.indd 33
11. 11. 30
2:16
34 Operating
Advanced Operations
Recording to USB
You can record music or sound souce to USB device
by connecting in to the port on the unit.
y During recording MP3/WMA, there is no
sound.
1. Connect the USB device to the unit.
y When you stop recording during playback,
the file that has been recorded at that time
will be stored. (Audio CD only)
2. Select a mode in which you want to record.
Play back a sound source first.
3. Start the recording by pressing X REC.
4. To stop recording, press Z (STOP).
[All tracks/ files recording]
Record to USB in stop or play mode.
[Program list recording]
After marking desired file(s) and you can record
it to USB (Refer to the page 28).
4
, Note
y You can check the recording percentage
rate for the USB record on the screen during
the recording. (Audio CD or MP3/ WMA CD
only)z
It’ll be stored as follows.
Operating
Audio CD
MP3/ WMA
y Do not remove the USB device or turn
off the unit during USB recording. If not,
an incomplete file may be made and not
deleted on PC.
y If USB recording does not work, the
message like “NO USB”, “ERROR”, “USB FULL”
or “NO REC” is displayed on the display
window.
y Multi card reader device or external HDD
can not be used for USB recording.
y A file is recorded by 128 Mbyte (about 2
hours) when you record for a long term.
There are recorded less than 4 files.
y When you stop recording during playback,
the file will not be stored.
y In the state CD-G, DTS disc USB record is not
operated.
y The files in the sub-folders are not recorded
during all track recording.
y You may not record more than 999 files.
The other
sources (Tuner,
Portable)
y The nunbering of the recording file is
entered from the lowest number. So if you
delete some of the recording files, the next
recording file could be the lowest number
among them.
The making of unauthorized copies of copyprotected material, including computer programs,
files, broadcasts and sound recordings, may be
an infringement of copyrights and constitute a
criminal offense. This equipment should not be
used for such purposes.
Be responsible
Respect copyrights.
TB106-D0F-ADEULL-ENG.indd 34
11. 11. 30
2:16
Troubleshooting 35
Troubleshooting
PROBLEM
No power
No picture
CORRECTION
Plug the power cord into the wall outlet securely.
Select the appropriate video input mode on the TV so the picture
from the unit appears on the TV screen.
Connect the video cables securely to both the TV and unit.
Select the correct input mode of the unit so you can hear the sound
from the unit.
There is little or no sound
Connect the audio cables into the connection terminals correctly.
Replace with a new audio cable.
The DVD picture quality is poor
Clean the disc using a soft cloth with outward strokes.
Insert a disc.
A DVD/CD will not play
Insert a playable disc (check the disc type, colour system and
regional code).
Enter your password or change the rating level.
Humming noise heard while a DVD
or CD is playing
Clean the disc using a soft cloth with outward strokes.
5
Move unit and audio components further away from your TV.
Troubleshooting
Check the antenna connection and adjust its position.
Radio stations can’t be tuned in
properly
Attach an external aerial if necessary.
Tune to the station manually.
Preset some radio stations, see page 31 for details.
The remote is not pointed directly at the unit.
Point the remote directly at the unit.
The remote is too far from the unit.
Use the remote within 23 feet (7m) of the unit.
The remote control doesn’t work
well / at all
There is an obstacle in the path between the remote control and
the unit.
Remove the obstacle.
The battery in the remote control are flat.
Replace the battery with new ones.
iPod does not work.
TB106-D0F-ADEULL-ENG.indd 35
Check whether the player is connected to the unit correctly.
Connect it to the unit correctly.
11. 11. 30
2:16
36 Appendix
Area Code List
Choose an area code from this list.
Area
Code Area
Afghanistan
AF Fiji
Code Area
Code Area
Code
FJ Monaco
MC Singapore
SG
SK
Argentina
AR Finland
FI Mongolia
MN Slovak Republic
Australia
AU France
FR Morocco
MA Slovenia
Austria
AT Germany
DE Nepal
NP South Africa
ZA
Belgium
BE Great Britain
GB Netherlands
NL South Korea
KR
Bhutan
BT Greece
GR Antilles
AN Spain
ES
Bolivia
BO Greenland
GL New Zealand
NZ Sri Lanka
LK
SI
Brazil
BR Hong Kong
HK Nigeria
NG Sweden
SE
Cambodia
KH Hungary
HU Norway
NO Switzerland
CH
Canada
CA India
IN Oman
OM Taiwan
TW
Chile
CL Indonesia
ID Pakistan
PK Thailand
TH
China
CN Israel
IL Panama
PA Turkey
TR
Colombia
CO Italy
IT Paraguay
PY Uganda
UG
Congo
CG Jamaica
JM Philippines
PH Ukraine
UA
Costa Rica
CR Japan
JP Poland
PL United States
US
Croatia
HR Kenya
KE Portugal
PT Uruguay
UY
Czech Republic
CZ Kuwait
KW Romania
RO Uzbekistan
UZ
Denmark
DK Libya
Ecuador
EC Luxembourg
LY Russian
LU Federation
Egypt
EG Malaysia
6
El Salvador
SV Maldives
MY Saudi Arabia
MV Senegal
Appendix
Ethiopia
ET Mexico
MX
TB106-D0F-ADEULL-ENG.indd 36
Vietnam
RU Zimbabwe
SA
VN
ZW
SN
11. 11. 30
2:16
Appendix 37
Language code List
Use this list to input your desired language for the following initial settings: [Disc Audio],
[Disc Subtitle] and [Disc Menu].
Code
Language
Code
Language
Code
Language
Code
Afar
6565
French
7082
Lithuanian
7684
Sindhi
8368
Afrikaans
6570
Frisian
7089
Macedonian
7775
Singhalese
8373
Albanian
8381
Galician
7176
Malagasy
7771
Slovak
8375
Ameharic
6577
Georgian
7565
Malay
7783
Slovenian
8376
Arabic
6582
German
6869
Malayalam
7776
Spanish
6983
Armenian
7289
Greek
6976
Maori
7773
Sudanese
8385
Assamese
6583
Greenlandic
7576
Marathi
7782
Swahili
8387
Aymara
6588
Guarani
7178
Moldavian
7779
Swedish
8386
Azerbaijani
6590
Gujarati
7185
Mongolian
7778
Tagalog
8476
Bashkir
6665
Hausa
7265
Nauru
7865
Tajik
8471
Basque
6985
Hebrew
7387
Nepali
7869
Tamil
8465
Bengali; Bangla
6678
Hindi
7273
Norwegian
7879
Telugu
8469
Bhutani
6890
Hungarian
7285
Oriya
7982
Thai
8472
Bihari
6672
Icelandic
7383
Panjabi
8065
Tonga
8479
Breton
6682
Indonesian
7378
Pashto, Pushto
8083
Turkish
8482
Bulgarian
6671
Interlingua
7365
Persian
7065
Turkmen
8475
Burmese
7789
Irish
7165
Polish
8076
Twi
8487
Byelorussian
6669
Italian
7384
Portuguese
8084
Ukrainian
8575
Chinese
9072
Japanese
7465
Quechua
8185
Urdu
8582
Croatian
7282
Kannada
7578
Rhaeto-Romance 8277
Uzbek
8590
Czech
6783
Kashmiri
7583
Rumanian
8279
Vietnamese
8673
Danish
6865
Kazakh
7575
Russian
8285
Volapük
8679
Dutch
7876
Kirghiz
7589
Samoan
8377
Welsh
6789
English
6978
Korean
7579
Sanskrit
8365
Wolof
8779
Esperanto
6979
Kurdish
7585
Scots Gaelic
7168
Xhosa
8872
Estonian
6984
Laothian
7679
Serbian
8382
Yiddish
7473
Faroese
7079
Latin
7665
Serbo-Croatian
8372
Yoruba
8979
Fiji
7074
Latvian, Lettish
7686
Shona
8378
Zulu
9085
Finnish
7073
Lingala
7678
TB106-D0F-ADEULL-ENG.indd 37
11. 11. 30
6
Appendix
Language
2:16
38 Appendix
Trademarks and
Licenses
iPod is a trademark of Apple Inc., registered in
the U.S. and other countries.
iPhone is a trademark of Apple Inc. “Made
for iPod” and “Made for iPhone” mean that
an electronic accessory has been designed
to connect specifically to iPod or iPhone
respectively, and has been certified by the
developer to meet Apple performance standards.
Apple is not responsible for the operation of
this device or its compliance with safety and
regulatory standards.
Please note that the use of this accessory with
iPod, iPhone may affect wireless performance.
DivX®, DivX Certified® and associated logos are
trademarks of Rovi Corporation or its subsidiaries
and are used under license.
ABOUT DIVX VIDEO: DivX® is a digital video
format created by DivX, LLC, a subsidiary of Rovi
Corporation. This is an official DivX Certified®
device that plays DivX video. Visit divx.com for
more information and software tools to convert
your files into DivX videos.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX
Certified® device must be registered in order to
play purchased DivX Video-on-Demand (VOD)
movies. To obtain your registration code, locate
the DivX VOD section in your device setup menu.
Go to vod.divx. com for more information on
how to complete your registration.
What is SIMPLINK?
HDMI, the HDMI logo and High-Definition
Multimedia Interface are trademarks or registered
trademarks of HDMI licensing LLC.
Some functions of this unit are controlled by
TV’s remote control when this unit and LG TV
with SIMPLINK are connected through HDMI
connection. Controllable functions by LG TV’s
remote control; Play, Pause, Scan, Skip, Stop,
Power Off, etc.
y Refer to the TV owner’s manual for the details
of SIMPLINK function.
6
Appendix
“DVD Logo” is a trademark of DVD Format/Logo
Licensing Corporation.
y LG TV with SIMPLINK function has the logo as
shown above.
y Use a higher version cable than High Speed
HDMI™ cable.
Manufactured under license from Dolby
Laboratories. Dolby and the double-D symbol
are trademarks of Dolby Laboratories.
TB106-D0F-ADEULL-ENG.indd 38
11. 11. 30
2:16
Appendix 39
Specifications
General
Power requirements
110 - 240 V, 50/ 60 Hz
Power consumption
40W
Dimensions (W x H x D)
240 X 136 X 240 mm without foot
Net Weight (Approx.)
2.9 kg
Operating temperature
41 °F to 95 °F (5 °C to 35 °C)
Operating humidity
5 % to 90 %
Inputs/ Outputs
VIDEO OUT
1.0 V (p-p), 75 Ω, sync negative, RCA jack x 1
COMPONENT VIDEO OUT
(Y) 1.0 V (p-p), 75 Ω, sync negative, RCA jack x 1
(Pb)/(Pr) 0.7 V (p-p), 75 Ω, RCA jack x 2
HDMI OUT (video/audio)
19 pin Type A, HDMI™ Connector
DIGITAL IN (OPTICAL)
3 V (p-p), Optical jack x 1
ANALOG AUDIO IN
PORT. IN
0.6 Vrms (1 kHz), 600 Ω, RCA jack (L, R) x 1
0.5Vrms (3.5 mm stereo jack)
System
Laser
Semiconductor laser, wavelength: 650 nm
Signal system
Standard NTSC/ PAL color TV system
Frequency response
40 Hz to 20 kHz
Signal-to-noise ratio
More than 80 dB
Harmonic distortion
0.5 % at 1 W
More than 80 dB
Bus Power Supply
USB DC 5 V 0 500 mA
iPod DC 5 V 0 1 A
Appendix
Dynamic range
6
Amplifier
Stereo mode
50 W + 50 W
Tuner
FM Tuning Range
TB106-D0F-ADEULL-ENG.indd 39
87.5 to 108.0 MHz or 87.50 to 108.00 MHz
11. 11. 30
2:16
40 Appendix
Front Speaker
Type
2 Way 2 speaker
Impedance Rated
8Ω
Input Power
50 W
Max. Input Power
100 W
Net Dimensions (W x H x D)
160 X 266 X 206 mm
Net Weight
2.2 kg
y Design and specifications are subject to change without notice.
6
Appendix
TB106-D0F-ADEULL-ENG.indd 40
11. 11. 30
2:16
Appendix
Maintenance
41
Notes on Discs
Handling Discs
Handling the Unit
When shipping the unit
Please save the original shipping carton and
packing materials. If you need to ship the unit, for
maximum protection, re-pack the unit as it was
originally packed at the factory.
Keeping the exterior surfaces clean
y Do not use volatile liquids such as insecticide
spray near the unit.
y Wiping with strong pressure may damage the
surface.
y Do not leave rubber or plastic products in
contact with the unit for a long period of time.
Cleaning the unit
To clean the player, use a soft, dry cloth. If the
surfaces are extremely dirty, use a soft cloth lightly
moistened with a mild detergent solution. Do not
use strong solvents such as alcohol, benzine, or
thinner, as these might damage the surface of the
unit.
Do not touch the playback side of the disc. Hold
the disc by the edges so that fingerprints do not
get on the surface. Never stick paper or tape on the
disc.
Storing Discs
After playing, store the disc in its case. Do not
expose the disc to direct sunlight or sources of heat
and never leave it in a parked car exposed to direct
sunlight.
Cleaning Discs
Fingerprints and dust on the disc can cause poor
picture quality and sound distortion. Before playing,
clean the disc with a clean cloth. Wipe the disc from
the center to out.
Do not use strong solvents such as alcohol,
benzine, thinner, commercially available cleaners,
or anti-static spray intended for older vinyl records.
Maintaining the Unit
The unit is a high-tech, precision device. If the
optical pick-up lens and disc drive parts are dirty
or worn, the picture quality could be diminished.
For details, please contact your nearest authorized
service center.
Appendix
TB106-D0F-ADEULL-ENG.indd 41
6
11. 11. 30
2:16
TB106-D0F-ADEULL-ENG.indd 42
11. 11. 30
2:16
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement