LG | LG 75UL3E-T | Owner's Manual | LG 75UL3E-T Owner's Manual

LG 75UL3E-T Owner's Manual
OWNER’S MANUAL
Safety and Reference
LG Digital Signage
(MONITOR SIGNAGE)
Please read this manual carefully before operating your set and retain
it for future reference.
www.lg.com
Copyright © 2018 LG Electronics Inc. All Rights Reserved.
Warning! Safety Instructions
ENGLISH
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.
REFER TO QUALIFIED SERVICE PERSONNEL.
This symbol is intended to alert the user to the presence of
uninsulated “dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude to constitute a risk
of electric shock to persons.
This symbol is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
WARNING : TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK,
DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
•• TO PREVENT THE SPREAD OF FIRE, KEEP CANDLES OR OTHER ITEMS
WITH OPEN FLAMES AWAY FROM THIS PRODUCT AT ALL TIMES.
•• Do not place the monitor and/or remote control in the following
environments:
-- Keep the product away from direct sunlight.
-- An area with high humidity such as a bathroom.
-- Near any heat source such as stoves and other devices that produce
heat.
-- Near kitchen counters or humidifiers where they can easily be
exposed to steam or oil.
-- An area exposed to rain or wind.
-- Do not expose to dripping or splashing and do not place objects
filled with liquids, such as vases, cups, etc. on or over the apparatus
(e.g., on shelves above the unit).
-- Near flammable objects such as gasoline or candles, or expose the
monitor to direct air conditioning.
-- Do not install in excessively dusty places.
Otherwise, this may result in fire, electric shock, combustion/
explosion, malfunction or product deformation.
2
•• Ventilation
-- Install your monitor where there is proper ventilation. Do not
install in a confined space such as a bookcase.
-- Do not install the product on a carpet or cushion.
-- Do not block or cover the product with cloth or other materials
while unit is plugged in.
•• Take care not to touch the ventilation openings. When watching the
monitor for a long period, the ventilation openings may become hot.
•• Protect the power cord from physical or mechanical abuse, such as
being twisted, kinked, pinched, closed in a door, or walked upon. Pay
particular attention to plugs, wall outlets, and the point where the
cord exits the device.
•• Do not move the monitor whilst the Power cord is plugged in.
•• Do not use a damaged or loosely fitting power cord.
•• Be sure to grasp the plug when unplugging the power cord. Do not
pull on the power cord to unplug the monitor.
•• Do not connect too many devices to the same AC power outlet as this
could result in fire or electric shock.
•• Disconnecting the Device from the Main Power
-- The power plug is the disconnecting device. In case of an
emergency, the power plug must remain readily accessible.
•• Do not let your children climb or cling onto the monitor. Otherwise,
the monitor may fall over, which may cause serious injury.
•• Batteries
-- Store the accessories (battery, etc.) in a safe location out of the
reach of children.
-- Do not short circuit, disassemble, or allow the batteries to
overheat. Do not dispose of batteries in a fire. Batteries should not
be exposed to excessive heat.
•• Moving
-- When moving, make sure the product is turned off, unplugged,
and all cables have been removed. It may take 2 or more people to
carry larger monitors. Do not press or put stress on the front panel
of the monitor. Otherwise, this may result in product damage, fire
hazard or injury.
•• Keep the packing anti-moisture material or vinyl packing out of the
reach of children.
•• Do not allow an impact shock, any objects to fall into the product,
and do not drop anything onto the screen.
•• Do not press strongly upon the panel with a hand or a sharp
object such as a nail, pencil, or pen, or make a scratch on it. It may
cause damage to screen.
•• Cleaning
-- When cleaning, unplug the power cord and wipe gently with a
soft/dry cloth. Do not spray water or other liquids directly on the
monitor. Do not clean your monitor with chemicals including glass
cleaner, any type of air freshener, insecticide, lubricants, wax (car,
industrial), abrasive, thinner, benzene, alcohol etc., which can
damage the product and/or its panel. Otherwise, this may result in
electric shock or product damage.
ENGLISH
•• Make sure the power cord is connected securely to the monitor and
wall socket if not secured damage to the Plug and socket may occur
and in extreme cases a fire may break out.
•• Do not insert metallic or inflammable objects into the product. If a
foreign object is dropped into the product, unplug the power cord
and contact the customer service.
•• Do not touch the end of the power cord while it is plugged in. You
may be electrocuted.
•• If any of the following occur, unplug the product immediately
and contact your local customer service.
-- The product has been damaged.
-- If water or another substance enters the product (like an AC
adapter, power cord, or monitor).
-- If you smell smoke or other odors coming from the monitor.
-- When lightning storms or when unused for long periods of time.
Even the monitor is turned off by remote control or button, AC power
source is connected to the unit if not unplugged in.
•• Do not use high voltage electrical equipment near the monitor (e.g.,
a bug zapper). This may result in product malfunction.
•• Do not attempt to modify this product in any way without written
authorization from LG Electronics. Accidental fire or electric shock
can occur. Contact your local customer service for service or repair.
Unauthorized modification could void the user’s authority to operate
this product.
•• Use only an authorized attachments / accessories approved by
LG Electronics. Otherwise, this may result in fire, electric shock,
malfunction, or product damage.
•• Never disassemble the AC adapter or power cord. This may result in
fire or electric shock.
•• Handle the adapter carefully to avoid dropping or striking it. An
impact could damage the adapter.
•• To reduce the risk of fire or electrical shock, do not touch the monitor
with wet hands. If the power cord prongs are wet or covered with
dust, dry the power plug completely or wipe dust off.
3
Preparing
Wall Mounting Bracket
(Depending on model)
ENGLISH
•• If the monitor is turned on for the first time after it was shipped from
the factory, initialization of the monitor may take a few minutes.
•• Image shown may differ from your monitor.
•• Your monitor’s OSD (On Screen Display) may differ slightly from that
shown in this manual.
•• The available menus and options may differ from the input source or
product model that you are using.
•• New features may be added to this monitor in the future.
•• The device must be easily accessed to a location outlet near the
access. Some devices are not made by turning on / off button, turning
off the device and unplugging the power cord.
•• The items supplied with your product may vary depending on the
model.
•• Product specifications or contents of this manual may be changed
without prior notice due to upgrade of product functions.
•• For an optimal connection, HDMI cables and USB devices should have
bezels less than 10 mm thick and 18 mm width. Use an extension
cable that supports USB if the USB cable or USB memory stick
does not fit into your monitor’s USB port.
B
B
A
A
* A<
= 10 mm
* B<
= 18 mm
•• Use a certified cable with the HDMI logo attached.
•• If you do not use a certified HDMI cable, the screen may not display or
a connection error may occur. (Recommended HDMI Cable Types)
-- High-Speed HDMI®/TM Cable (3 m or less)
-- High-Speed HDMI®/TM Cable with Ethernet (3 m or less)
•• SuperSign Software & Manual
-- Downloading from the LG Electronics website.
-- Visit the LG Electronics website (http://partner.lge.com) and
download the latest software for your model.
4
Make sure to use screws and wall mount bracket that meet the VESA
standard. Standard dimensions for the wall mount kits are described in
the following table.
A
B
Model
65UL3E
VESA (A x B) (mm)
300 x 300
75UL3E
86UL3E
600 x 400
Standard screw
Number of screws
M6
4
M8
4
Wall mount bracket OLW480B
LSW640B
Lifting and moving the
monitor
•• It is recommended to move the monitor in the box or packing
material that the monitor originally came in.
•• Before moving or lifting the monitor, disconnect the power cord and
all cables.
•• When holding the monitor, the screen should face away from you to
avoid damage.
ENGLISH
Please note the following advice to prevent the monitor from being
scratched or damaged and for safe transportation regardless of its type
and size.
•• When transporting the monitor, do not expose the monitor to jolts or
excessive vibration.
•• When transporting the monitor, keep the monitor upright, never turn
the monitor on its side or tilt towards the left or right.
•• Do not apply excessive pressure to cause flexing / bending of frame
chassis as it may damage screen.
•• When handling the monitor, be careful not to damage the protruding
buttons.
•• Avoid touching the screen at all times, as this may result in
damage to the screen.
•• Do not move the monitor by holding the cable holders, as
the cable holders may break, and injuries and damage to the
monitor may occur.
•• When attaching the stand to the monitor set, place the
screen facing down on a cushioned table or flat surface to
protect the screen from scratches.
•• Hold the top and bottom of the monitor frame firmly. Make sure not
to hold the transparent part, speaker, or speaker grill area.
•• When transporting a large monitor, there should be at least 2 people.
•• When transporting the monitor by hand, hold the monitor as shown
in the following illustration.
5
ENGLISH
Mounting on a Table
Using the Kensington security
system
1 Lift and tilt the monitor into its upright position on a table.
• Leave a 10 cm (minimum) space from the wall for proper
ventilation.
The Kensington security system connector is located at the rear of the
monitor. For more information of installation and using, refer to the
manual provided with the Kensington security system or
visit http://www.kensington.com. Connect the Kensington security
system cable between the monitor and a table.
10 cm
10 cm
10 cm
10 cm
10 cm
(Depending on model)
2 Connect the power cord to a wall outlet.
•• Do not apply foreign substances (oils, lubricants, etc.) to the
screw parts when assembling the product.
(Doing so may damage the product.)
•• If you install the monitor on a stand, you need to take actions
to prevent the product from overturning. Otherwise, the
product may fall over, which may cause injury.
•• Do not use any unapproved items to ensure the safety and
product life span.
•• Any damage or injuries caused by using unapproved items
are not covered by the manufacturer’s warranty.
•• Make sure that the screws are inserted correctly and fastened
securely. (If they are not fastened securely enough, the
monitor may tilt forward after being installed.) Do not use
too much force and over tighten the screws; otherwise screw
may be damaged and not tighten correctly.
6
(Depending on model)
Mounting to the Wall
•• When installing the wall mounting bracket, it is recommended to
cover the stand hole using tape, in order to prevent the influx of dust
and insects. (Depending on model)
ENGLISH
Attach an optional wall mount bracket at the rear of the monitor
carefully and install the wall mount bracket on a solid wall
perpendicular to the floor. When you attach the monitor to other
building materials, please contact qualified personnel. LG recommends
that wall mounting be performed by a qualified professional installer.
We recommend the use of LG’s wall mount bracket. LG’s wall mount
bracket is easy to move with cables connected. When you do not use
LG’s wall mount bracket, please use a wall mount bracket where the
device is adequately secured to the wall with enough space to allow
connectivity to external devices. It is advised to connect all the cables
before installing fixed wall mounts.
Stand hole
m
10 c
10 cm
10 cm
A
10 cm
A
A
10 cm
A
•• This model does not support rotating installation of the monitor
except the default installation.
(Depending on model)
•• Remove the stand before installing the monitor on a wall
mount by performing the stand attachment in reverse.
•• For more information of screws and wall mount bracket,
refer to the Separate purchase.
•• If you intend to mount the product to a wall, attach VESA
standard mounting interface (optional parts) to the back
of the product. When you install the set to use the wall
mounting bracket (optional parts), fix it carefully so as not
to drop.
•• When mounting a monitor on the wall, make sure not to
install the monitor by hanging the power and signal cables
on the back of the monitor.
•• Do not install this product on a wall if it could be exposed
to oil or oil mist. This may damage the product and cause
it to fall.
7
Connections
ENGLISH
Connect various external devices to the monitor and switch input
modes to select an external device. For more information of external
device’s connection, refer to the manual provided with each device.
Other connections
Connect your monitor to external devices. For the best picture and audio
quality, connect the external device and the monitor with the HDMI
cable. Some separate cable is not provided.
HDMI
•• Supported HDMI Audio format (Depending on model):
DTS (44.1 kHz / 48 kHz / 88.2 kHz / 96 kHz),
DTS HD (44.1 kHz / 48 kHz / 88.2 kHz / 96 kHz / 176.4 kHz / 192 kHz),
True HD (48 kHz),
Dolby Digital / Dolby Digital Plus (32 kHz / 44.1 kHz / 48 kHz),
PCM (32 kHz / 44.1 kHz / 48 kHz / 96 kHz / 192 kHz)
(Only UHD models)
••
8
(SETTINGS)
( ) [Picture] [Additional
Settings] [HDMI ULTRA HD Deep Colour]
-- On : Support 4K @ 50/60 Hz (4:4:4, 4:2:2, 4:2:0)
-- Off : Support 4K @ 50/60 Hz 8 bit (4:2:0)
If the device connected to Input Port also supports ULTRA HD Deep
Colour, your picture may be clearer. However, if the device doesn’t
support it, it may not work properly. In that case, change the
monitor’s [HDMI ULTRA HD Deep Colour] setting to [Off].
USB
Some USB Hubs may not work. If a USB device connected through a USB
Hub is not detected, connect it directly to the USB port on the monitor.
External Devices
Available external devices are: Blu-ray player, HD receivers, DVD players,
VCRs, audio systems, USB storage devices, PC, gaming devices, and
other external devices.
•• The external device connection may differ from the model.
•• Connect external devices to the monitor regardless of the order of the
monitor port.
•• Refer to the external equipment’s manual for operating instructions.
•• If you connect a gaming device to the monitor, use the cable supplied
with the gaming device.
•• If ULTRA HD content is played on your PC, video or audio may become
disrupted intermittently depending on your PC’s performance.
(Depending on model)
•• When connecting via a wired LAN, it is recommended to use a CAT 7
cable. (Only when
port is provided.)
Using Button
Network
Wired network connection
You can simply operate the monitor functions, using the button.
ENGLISH
This monitor can be connected to a Pro:Centric server via the LAN port.
After making the physical connection, the monitor needs to be set up
for network communication.
Connect the LAN port of the Modem or Router from Pro:Centric server to
the LAN port on the monitor.
Basic functions
Power On (Press the button When the monitor is turned
off.)
Power Off1 (Press and Hold the button When the
monitor is turned on.)
Menu Control (Press the button When the monitor is
turned on.2)
Broadband Modem
Router
Pro:Centric Server
(Depending on model)
Broadband Modem
Menu Selection (Press and Hold the button when you
access menu control.3)
1 All running apps will close.
2 You can access and adjust the menu by pressing the button when
monitor is on.
3 You can use the function when you access menu control.
Adjusting the menu
When the monitor is turned on, press the
adjust the Menu items using the button.
Pro:Centric Server
(Depending on model)
1 Connect the LAN port of the Modem or Router to the LAN port on
the monitor.
button one time. You can
Turns the power off.
Changes the input source.
Adjusts the volume level.
2 Connect the LAN port of the PC to the AUX LAN port on the
monitor. (Depending on model)
•• Do not connect a modular phone cable to the LAN port.
•• Since there are various connection methods, please follow
the specifications of your telecommunication carrier or
internet service provider.
9
Using Remote Control
ENGLISH
The descriptions in this manual are based on the buttons on the remote
control. Please read this manual carefully and use the monitor correctly.
To replace batteries, open the battery cover, replace batteries (1.5
V AAA) matching the and ends to the label inside the
compartment, and close the battery cover. To remove the batteries,
perform the installation actions in reverse.
Make sure to point the remote control toward the remote control sensor
on the monitor.
(Some buttons and services may not be provided depending on models
or regions.)
* To use the button, press and hold for more than 3 seconds.
(POWER) Turns the monitor on or off.
Turns the monitor on.
Turns the monitor off.
Adjusts the brightness of the screen to reduce
energy consumption.
(INPUT) Changes the input source.
Used for viewing 3D videos.
Toggles between numerical and alphabetical.
10
Number and Alphabet buttons Enters numerical or alphabetical
characters depending upon the setting.
Deletes the entered numerical or alphabetical character.
Volume Up/Down Button Adjusts the volume.
Selects the Aspect Ratio mode.
Automatically adjusts picture position and minimizes image
instability (available for RGB input only).
(MUTE) Mutes all sounds.
Adjusts the brightness of the display. PAGE function is not
supported in this model.
Selects the Picture Mode.
(HOME) Activates the Launcher.
Enters the White Balance menu.
(SETTINGS) Accesses the main menus or saves your input and
exit menus.
SuperSign menu key.
Navigation Buttons Scrolls through menus or options.
Selects menus or options and confirms your input.
(BACK) Allows you to move back one step in the user interaction
function.
Quit all OSD tasks and applications.
Troubleshooting
Allows you to control various multimedia devices
to enjoy multimedia simply by using the remote control through the
SimpLink menu.
Selects the TILE Mode.
When the Picture ID number matches the Set
ID number, you can control whichever monitor you want in multidisplay format.
USB Menu Control Buttons Controls media playback.
Trick key may not be supported on some
models.
•• Check the power control settings. The power supply may be
interrupted.
•• Check if the auto-off function is activated on the settings related
time.
The software version can be updated for improvement in performance.
ENGLISH
Customer needs to ensure the compatibility of customer’s equipment
with LGE software. If needed, please consult with LGE and upload
revised software version according to the guidance provided by LGE.
Cannot control the monitor with the remote control.
•• Check the remote control sensor on the product and try again.
•• Check if there is any obstacle between the product and the remote
control.
•• Check if the batteries are still working and properly installed ( to
, to ).
No image display and no sound is produced.
•• Check if the product is turned on.
•• Check if the power cord is connected to a wall outlet.
•• Check if there is a problem in the wall outlet by connecting other
products.
The monitor turns off suddenly.
When connecting to the PC (HDMI/DVI), no signal is detected.
•• Turn the monitor off/on using the remote control.
•• Reconnect the HDMI cable.
•• Restart the PC with the monitor on.
•• Do not mix new batteries with old batteries. This may cause
the batteries to overheat and leak.
•• Failure to match the correct polarities of the battery may
cause the battery to burst or leak, resulting in fire, personal
injury, or ambient pollution.
•• This apparatus uses batteries. In your community there
might be regulations that require you to dispose of these
batteries properly due to environmental considerations.
Please contact your local authorities for disposal or recycling
information.
•• Batteries inside or inside the product shall not be exposed to
excessive heat such as sunshine, fire or the like.
11
ENGLISH
Abnormal display
Generated sound
•• If the product feels cold to the touch, there may be a small “flicker”
when it is turned on. This is normal, there is nothing wrong with
product.
•• This panel is an advanced product that contains millions of pixels.
You may see tiny black dots and/or brightly coloured dots (red, blue
or green) at a size of 1 ppm on the panel. This does not indicate a
malfunction and does not affect the performance and reliability of
the product. This phenomenon also occurs in third-party products
and is not subject to exchange or refund.
•• You may find different brightness and color of the panel depending
on your viewing position(left/right/top/down).
This phenomenon occurs due to the characteristic of the panel. It is
not related with the product performance, and it is not malfunction.
•• Displaying a still image for a prolonged period of time may cause
image sticking. Avoid displaying a fixed image on the monitor screen
for a long period of time.
•• “Cracking” noise: A cracking noise that occurs when watching or
turning off the monitor is generated by plastic thermal contraction
due to temperature and humidity. This noise is common for products
where thermal deformation is required.
•• Electrical circuit humming/panel buzzing: A low level noise is
generated from a high-speed switching circuit, which supplies a large
amount of current to operate a product. It varies depending on the
product. This generated sound does not affect the performance and
reliability of the product.
•• When cleaning the product, be careful not to allow any
liquid or foreign objects to enter the gap between the
upper, left or right side of the panel and the guide panel.
(Depending on model)
•• Make sure to wring any excess water or cleaner from the
cloth.
•• Do not spray water or cleaner directly onto the monitor
screen.
•• Make sure to spray just enough of water or cleaner onto a
dry cloth to wipe the screen.
12
Specifications
ENGLISH
Wireless module (LGSBWAC72) specifications
Wireless LAN (IEEE 802.11a/b/g/n/ac)
Frequency Range
Output Power (Max.)
2,400 to 2,483.5 MHz
14 dBm
5,150 to 5,725 MHz
16.5 dBm
5,725 to 5,850 MHz (Not for EU)
11.5 dBm
Bluetooth
Frequency Range
Output Power (Max.)
2,400 to 2,483.5 MHz
8.5 dBm
As band channels can vary per country, the user cannot change or adjust the operating frequency. This product is configured for the regional
frequency table.
For consideration of the user, this device should be installed and operated with a minimum distance of 20 cm between the device and the body.
“IEEE 802.11ac” is not available in all countries.
Environment condition
Operating Temperature
0 °C to 40 °C
Operating Humidity
Less than 80 %
Storage Temperature
-20 °C to 60 °C
Storage Humidity
Less than 85 %
Embedded battery
Applied
13
HDMI-DTV supported mode
Horizontal
Frequency (kHz)
Vertical
Frequency (Hz)
31.469
59.94
31.5
31.47
60.00
59.94
720 x 576p
31.5
31.25
44.96
60.00
50.00
59.94
1280 x 720p
45
60.00
37.5
28.125
Resolution
ENGLISH
640 x 480p
720 x 480p
1920 x 1080i
1920 x 1080p
3840 x 2160p
4096 x 2160p
14
HDMI-PC supported Mode
•• PC audio is not supported.
•• Use HDMI IN 1 for PC mode. (Depending on model)
Resolution
Horizontal
Frequency (kHz)
Vertical
Frequency (Hz)
640 x 350
31.468
70.09
720 x 400
31.469
70.08
640 x 480
31.469
59.94
800 x 600
37.879
60.31
50.00
50.00
1024 x 768
48.363
60.00
1360 x 768
47.712
60.015
33.72
59.94
1152 x 864
54.348
60.053
33.75
26.97
60.00
23.976
1280 x 1024
63.981
60.020
27.00
24.000
1920 x 1080
67.5
60
33.71
29.97
33.75
30.00
56.25
50.00
67.432
59.94
67.5
60.00
135
120
134.86
119.88
112.5
53.95
100
23.98
54
24.00
56.25
25.00
61.43
29.97
67.5
30.00
112.5
50.00
134.865
59.94
135
53.95
60.00
23.98
54
24.00
56.25
25.00
61.43
29.97
67.5
30.00
112.5
50.00
134.865
59.94
135
60.00
3840 x 2160
4096 x 2160
135
120
54
24.00
56.25
25.00
67.5
30.00
53.95
23.97
54
24
Supported Photo Formats
Format
Resolution
File
Format
Minimum: 64 (W) x 64 (H)
.jpeg, .jpg,
.jpe
.png
.bmp
JPEG
Maximum (Normal Type): 15360 (W) x
8640 (H)
.mp3
Maximum (Progressive Type): 1920 (W)
x 1440 (H)
PNG
BMP
Minimum: 64 (W) x 64 (H)
Maximum: 5760 (W) x 5760 (H)
.wav
Minimum: 64 (W) x 64 (H)
Maximum: 1920 (W) x 1080 (H)
.ogg
.wma
.flac
Item
Info
Bit rate
32 Kbps - 320 Kbps
Sample freq.
16 kHz - 48 kHz
Support
MPEG1, MPEG2
Channels
mono, stereo
Bit rate
-
Sample freq.
8 kHz - 96 kHz
Support
PCM
Channels
mono, stereo
Bit rate
64 kbps - 320 kbps
Sample freq.
8 kHz - 48 kHz
Support
Vorbis
Channels
mono, stereo
Bit rate
128 kbps - 320 kbps
Sample freq.
8 kHz - 48 kHz
Support
WMA
Channels
up to 6 ch
Bit rate
-
Sample freq.
8 kHz - 96 kHz
Support
FLAC
Channels
mono, stereo
ENGLISH
File
Format
Supported Audio Formats
15
Supported Video Formats
Extension
ENGLISH
.asf
.wmv
Codec
Video
VC-1 Advanced Profile (except for
WMVA), VC-1 Simple and Main Profiles
Audio
WMA Standard (except for WMA v1/
WMA Speech)
Video
Xvid (except 3 warp-point GMC), H.264/
AVC, Motion Jpeg, MPEG-4
Audio
MPEG-1 Layer I, II, MPEG-1 Layer III
(MP3), Dolby Digital, LPCM, ADPCM, DTS
.avi
.mp4
.m4v
.mov
Video
H.264/AVC, MPEG-4, HEVC
Audio
Dolby Digital, Dolby Digital Plus, AAC,
MPEG-1 Layer III (MP3)
.3gp
Video
H.264/AVC, MPEG-4
.3g2
Audio
AAC, AMR-NB, AMR-WB
Video
MPEG-2, MPEG-4, H.264/AVC, VP8,
VP9, HEVC
Audio
Dolby Digital, Dolby Digital Plus, AAC,
PCM, DTS, MPEG-1 Layer I, II, MPEG-1
Layer III (MP3)
.mkv
.ts
Video
H.264/AVC, MPEG-2, HEVC
Audio
MPEG-1 Layer I, II, MPEG-1 Layer III
(MP3), Dolby Digital, Dolby Digital Plus,
AAC, PCM
.trp
.tp
.mts
.mpg
.mpeg
.dat
.vob
.mkv
.mp4
.ts
Video
MPEG-1, MPEG-2
Audio
MPEG-1 Layer I, II, MPEG-1 Layer III
(MP3)
Video
MPEG-1, MPEG-2
Audio
Dolby Digital, MPEG-1 Layer I, II,
DVD-LPCM
Video
H.264/AVC, HEVC
Audio
Dolby Digital, Dolby Digital Plus, AAC
Open Source Software
Notice Information
To obtain the source code under GPL, LGPL, MPL, and other open source
licenses, that is contained in this product, please visit
http://opensource.lge.com.
In addition to the source code, all referred license terms, warranty
disclaimers and copyright notices are available for download.
LG Electronics will also provide open source code to you on CD-ROM
for a charge covering the cost of performing such distribution (such
as the cost of media, shipping, and handling) upon email request to
opensource@lge.com.
This offer is valid for a period of three years after our last shipment of
this product. This offer is valid to anyone in receipt of this information.
Licenses
Supported licenses may differ by model.
The terms HDMI and HDMI High-Definition Multimedia Interface,
and the HDMI Logo are trademarks or registered trademarks of
HDMI Licensing Administrator, Inc. in the United States and other
countries.
For DTS patents, see http://patents.dts.com. Manufactured under
license from DTS Licensing Limited. DTS, the Symbol, & DTS and the
Symbol together, DTS 2.0 Channel, DTS 2.0+Digital Out, DTS-HD, and
DTS Virtual:X are registered trademarks or trademarks of DTS, Inc.
in the United States and/or other countries. © DTS, Inc. All Rights
Reserved.
Manufactured under license from Dolby Laboratories. Dolby, Dolby
Vision, Dolby Audio, Dolby Atmos, and the double-D symbol are
trademarks of Dolby Laboratories.
(Depending on model)
16
Record the model number and serial number of
the monitor.
Refer to the label on the back cover and quote
this information to your dealer when requiring
any service.
MODEL
SERIAL No.
OWNER’S MANUAL
RS-232C
Please read this manual carefully before operating your set and retain
it for future reference.
www.lg.com
IR CODES
•• This feature is not available for all models.
ENGLISH
Code
(Hexa)
08
C4
C5
95
0B
DC
32
10-19
2
Function
(POWER)
(INPUT)
Number Key 0-9
Alphabet buttons
Note
Remote control Button
(Power On/Off)
Remote control Button
Remote control Button
Remote control Button
Remote control Button
Remote control Button
Remote control Button
Remote control Button
2F
Remote control Button
02
Remote control Button
03
79
99
09
E0
E1
4D
7C
5F
43
Remote control Button
Remote control Button
Remote control Button
Remote control Button
Remote control Button
Remote control Button
Remote control Button
Remote control Button
Remote control Button
Remote control Button
(MUTE)
(HOME)
(SETTINGS)
Code
(Hexa)
3F
40
41
Function
Note
Remote control Button
Remote control Button
Remote control Button
07
Remote control Button
06
Remote control Button
44
28
5B
(BACK)
Remote control Button
Remote control Button
Remote control Button
7E
Remote control Button
7B
72
71
B1
B0
BA
8F
Remote control Button
(Red) Remote control Button
(Green) Remote control Button
Remote control Button
Remote control Button
Remote control Button
Remote control Button
8E
Remote control Button
63
Yellow
Remote control Button
61
Blue
Remote control Button
Phone
jack Type
(PC)
USB IN
EXTERNAL CONTROL DEVICE SETUP
(TV)
(Depending on model)
•• You need to purchase the phone-jack to RS-232C cable required for
the connection between the PC and the Signage, which is(TV)
specified
(PC)
in the manual.
* For other models, connect to the USB port.
1
3
* (PC)
The connection interface may differ from your Signage. (TV)
RS-232C IN
(CONTROL & SERVICE)
4
2
1
3
(PC)
(PC)
SERVICE ONLY
•• Image shown may differ from your Signage.
Connect the RS-232C (serial port) input jack to an external control
device (such as a computer or an A/V control system) to control the
product’s functions externally.
Connect the serial port of the control device to the RS-232C jack on the
product back panel.
•• RS-232C connection cables are not supplied with the product.
4
ENGLISH
RS-232C Setup
2
RS-232C IN
(TV)
(Signage)
(CONTROL & SERVICE)
Type of Connector : D-Sub 9-Pin Male
RS-232C IN
(CONTROL & SERVICE)
RS-232C IN
(CONTROL & SERVICE)
1
(*Not Provided)
5
6
No.
Pin name
2
3.5 V
RXD (Receive data)
3
TXD (Transmit data)
4
IR OUT from Signage
5
GND
6
No Connection
7
No Connection (5 V available in some models)
8
No Connection
9
No Connection (12 V available in some models)
1
(Depending on model)
9
3
RS-232C Configurations
Command Reference List
(Depending on model)
7-Wire Configurations
(Standard RS-232C cable)
ENGLISH
RXD
TXD
GND
DTR
DSR
RTS
CTS
PC
2
3
5
4
6
7
8
D-Sub 9
Command Command
Data
1
2
(Hexadecimal)
Signage
3
2
5
6
4
8
7
D-Sub 9
TXD
RXD
GND
DSR
DTR
CTS
RTS
3-Wire Configurations
(Not standard)
RXD
TXD
GND
DTR
DSR
RTS
CTS
PC
2
3
5
4
6
7
8
D-Sub 9
Communication Parameters
•• Baud rate: 9,600 bps (UART)
•• Data length: 8 bits
•• Parity : None
•• Stop bit: 1 bit
•• Communication code: ASCII code
•• Use a crossed (reverse) cable.
4
Signage
3
2
5
6
4
8
7
D-Sub 9
TXD
RXD
GND
DSR
DTR
RTS
CTS
1 Power
k
a
00 to 01
2 [Aspect Ratio]
k
c
(See p. 5)
3 Screen Mute
k
d
(See p. 6)
4 Volume Mute
k
e
00 to 01
5 Volume Control
k
f
00 to 64
6 [Contrast]
k
g
00 to 64
7 [Brightness]
k
h
00 to 64
8 [Colour]
k
i
00 to 64
9 [Tint]
k
j
00 to 64
10 [Sharpness]
k
k
00 to 32
11 OSD Select
k
l
00 to 01
12 Remote Control
Lock Mode
k
m
00 to 01
13 [Balance]
k
t
00 to 64
14 [Colour
Temperature]
x
u
00 to 64
15 [Energy Saving]
j
q
(See p. 8)
16 [AUTO
CONFIGURATION]
j
u
01
17 [Equalizer]
j
v
(See p. 8)
18 Key
m
c
(See p. 8)
19 Control Backlight
m
g
00 to 64
20 Input select
x
b
(See p. 9)
•• During USB operations such as DivX or EMF, all commands except
Power(ka) and Key(mc) are not executed and treated as NG.
Transmission / Receiving Protocol
(Depending on Model)
Transmission
OK Acknowledgement
(Command2)( )([Set ID])( )(OK)(Data)(x)
* The set transmits ACK (acknowledgement) based on this format
when receiving normal data. At this time, if the data is data read
mode, it indicates present status data. If the data is data write
mode, it returns the data of the PC computer.
Error Acknowledgement
(Command2)( )([Set ID])( )(NG)(Data)(x)
* The set transmits ACK (acknowledgement) based on this format
when receiving abnormal data from non-viable functions or
communication errors.
Data 00 : Illegal Code
►To
► control Power On/Off of the set.
Transmission
(k)(a)( )([Set ID])( )(Data)(Cr)
ENGLISH
(Command1)(Command2)( )([Set ID])( )(Data)(Cr)
(Command1) : First command to control the Signage. (j, k, m or x)
(Command2) : Second command to control the Signage.
([Set ID]) : You can adjust the set ID to choose desired Signage ID
number in option menu. Adjustment range is 1 to 99. When selecting
Set ID ‘0’, every connected set is controlled. Set ID is indicated as
decimal (1 to 99) on menu and as Hexadecimal (0 x 0 to 0 x 63) on
transmission/receiving protocol.
(Data) : To transmit command data. Transmit ‘FF’ data to read status
of command.
(Cr) : Carriage Return
ASCII code ‘0 x 0D’
( ) : ASCII code ‘space (0 x 20)’
1 Power (Command: k a)
Data 00 : [Off]
Data 01 : [On]
Ack
(a)( )([Set ID])( )(OK/NG)(Data)(x)
►To
► Show Signage is Power On/Off.
Transmission
(k)(a)( )([Set ID])( )(FF)(Cr)
Ack
(a)( )([Set ID])( )(OK/NG)(Data)(x)
* Similarly, if other functions transmit ‘0 x FF’ data based on this
format, Acknowledgement data feed back presents status about
each function.
* OK Ack., Error Ack. and other message may display on the screen
when Signage is power On.
2 [Aspect Ratio] (Command: k c) (Main Picture Size)
►To
► adjust the screen format. (Main picture format) You can also
adjust the screen format using the picture settings.
Transmission
(k)(c)( )([Set ID])( )(Data)(Cr)
Data 01 : [4:3] (Normal screen - Just Scan Off)
Data 02 : [16:9] (Wide screen - Just Scan Off)
Data 06 : [Original] (Just Scan Off)
Data 09 : [Just Scan]
Ack
(c)( )([Set ID])( )(OK/NG)(Data)(x)
* Using the PC input, you select either 16:9 or 4:3 screen aspect ratio.
5
3 Screen Mute (Command: k d)
6 [Contrast] (Command: k g)
►To
► select screen mute on/off.
►To
► adjust screen contrast.
You can also adjust contrast in the picture settings.
Transmission
ENGLISH
(k)(d)( )([Set ID])( )(Data)(Cr)
Transmission
(k)(g)( )([Set ID])( )(Data)(Cr)
Data 00 : Screen mute off (Picture on) / Video mute off
Data 01 : Screen mute on (Picture off)
Data 10 : Video mute on
Data Min : 00 to Max : 64
* Refer to "Real data mapping".
Ack
Ack
(d)( )([Set ID])( )(OK/NG)(Data)(x)
(g)( )([Set ID])( )(OK/NG)(Data)(x)
* In case of video mute on only, Signage will display On Screen Display
(OSD). But, in case of Screen mute on, Signage will not display OSD.
7 [Brightness] (Command: k h)
4 Volume Mute (Command: k e)
►To
► adjust screen brightness.
You can also adjust brightness in the picture settings.
►To
► control volume mute on/off.
You can also adjust mute using the mute button on remote control.
Transmission
(k)(e)( )([Set ID])( )(Data)(Cr)
Data 00 : Volume mute on (Volume off)
Data 01 : Volume mute off (Volume on)
Ack
(e)( )([Set ID])( )(OK/NG)(Data)(x)
5 Volume Control (Command: k f)
►To
► adjust volume.
You can also adjust volume with the volume buttons on remote
control.
Transmission
(k)(f)( )([Set ID])( )(Data)(Cr)
Data Min : 00 to Max : 64
* Refer to "Real data mapping".
Ack
(f)( )([Set ID])( )(OK/NG)(Data)(x)
6
Transmission
(k)(h)( )([Set ID])( )(Data)(Cr)
Data Min : 00 to Max : 64
* Refer to "Real data mapping".
Ack
(h)( )([Set ID])( )(OK/NG)(Data)(x)
8 [Colour] (Command: k i)
►To
► adjust the screen colour.
You can also adjust colour in the picture settings.
Transmission
(k)(i)( )([Set ID])( )(Data)(Cr)
Data Min : 00 to Max : 64
* Refer to "Real data mapping".
Ack
(i)( )([Set ID])( )(OK/NG)(Data)(x)
9 [Tint] (Command: k j)
12 Remote Control Lock Mode (Command: k m)
►To
► adjust the screen tint.
You can also adjust tint in the picture settings.
►To
► lock the front panel controls on the Signage and remote control.
Transmission
Data Red : 00 to Green : 64
* Refer to "Real data mapping".
Ack
(j)( )([Set ID])( )(OK/NG)(Data)(x)
10 [Sharpness] (Command: k k)
►To
► adjust the screen sharpness.
You can also adjust sharpness in the picture settings.
Transmission
(k)(k)( )([Set ID])( )(Data)(Cr)
Data Min : 00 to Max : 32
* Refer to "Real data mapping".
Ack
(k)( )([Set ID])( )(OK/NG)(Data)(x)
11 OSD Select (Command: k l)
►To
► select OSD (On Screen Display) on/off when controlling remotely.
Transmission
(k)(l)( )([Set ID])( )(Data)(Cr)
Data 00 : [Off]
Data 01 : [On]
Ack
(l)( )([Set ID])( )(OK/NG)(Data)(x)
(k)(m)( )([Set ID])( )(Data)(Cr)
ENGLISH
(k)(j)( )([Set ID])( )(Data)(Cr)
Transmission
Data 00 : [Off]
Data 01 : [On]
Ack
(m)( )([Set ID])( )(OK/NG)(Data)(x)
* If you are not using the remote control, use this mode. When main
power is on/off, external control lock is released.
* In the standby mode, if key lock is on, Signage will not turn on by
power on key of IR & Local Key.
13 [Balance] (Command: k t)
►To
► adjust balance.
You can also adjust balance in the audio settings.
Transmission
(k)(t)( )([Set ID])( )(Data)(Cr)
Data L : 00 to R : 64
* Refer to "Real data mapping".
Ack
(t)( )([Set ID])( )(OK/NG)(Data)(x)
14 [Colour Temperature] (Command: x u)
►To
► adjust Colour Temperature. You can also adjust Colour
Temperature in the picture settings.
Transmission
(x)(u)( )([Set ID])( )(Data)(Cr)
Data Warm: 00 to Cool:64
* Refer to "Real data mapping".
Ack
(u)( )([Set ID])( )(OK/NG)(Data)(x)
7
15 [Energy Saving] (Command: j q)
►To
► reduce the power consumption of the Signage. You can also
adjust Energy Saving in picture settings.
Transmission
ENGLISH
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Transmission
MSB
Level
Low
Power
Low
Power
Low
Power
Low
Power
Low
Power
Low
Power
►To
► adjust equalizer.
(j)(v)( )([Set ID])( )(Data)(Cr)
(j)(q)( )([Set ID])( )(Data)(Cr)
Power Saving
Function
7 6 5 4
17 [Equalizer] (Command : j v)
Description
3
2
1
0
0
0
0
0
[Off]
0
0
0
1
[Minimum]
0
0
1
0
[Medium]
0
0
1
1
[Maximum]
0
1
0
1
[Screen Off]
0
1
0
0
[Auto]
►‘[Auto]’
►
is available in Signage that supports ‘Intelligent Sensor’.
Ack
(q)( )([Set ID])( )(OK/NG)(Data)(x)
16 [AUTO CONFIGURATION] (Command: j u) (Only RGB support
model)
►To
► adjust picture position and minimize image shaking
automatically. It works only in RGB (PC) mode.
Transmission
(j)(u)( )([Set ID])( )(Data)(Cr)
Data 01 : To set
Ack
(u)( )([Set ID])( )(OK/NG)(Data)(x)
LSB
0
0
0
0
0
0
Frequency
4 3 2 1 0
Step
0 0 0
1st Band
0 0 0 0 0
0 (decimal)
0 0 1
2nd Band
0 0 0 0 1
1 (decimal)
0 1 0
3rd Band
... ... ... ... ...
...
0 1 1
4th Band
1 0 0 1 1
19 (decimal)
1 0 0
5th Band
1 0 1 0 0
20 (decimal)
Ack
(v)( )([Set ID])( )(OK/NG)(Data)(x)
18 Key (Command: m c)
►To
► send IR remote key code.
Transmission
(m)(c)( )([Set ID])( )(Data)(Cr)
Data IR CODES
Ack
(c)( )([Set ID])( )(OK/NG)(Data)(x)
19 Control Backlight (Command: m g)
►To
► control the backlight.
Transmission
(m)(g)( )([Set ID])( )(Data)(Cr)
Data Min : 00 to Max : 64
Ack
(g)( )([Set ID])( )(OK/NG)(Data)(x)
8
0
Data
Frequency
7 6 5
0
20 Input select (Command: x b) (Main Picture Input)
* Real data mapping
00 :
Step 0
►To
► select input source for main picture.
Transmission
Data Structure
MSB
0
LSB
0
0
0
0
External Input
0
0
0
A:
Step 10 ([Set ID] 10)
F:
10 :
Step 15 ([Set ID] 15)
Step 16 ([Set ID] 16)
64 :
Step 100
6E :
Step 110
73 :
74 :
Step 115
Step 116
CF :
Step 199
FE :
FF :
Step 254
Step 255
ENGLISH
(x)(b)( )([Set ID])( )(Data)(Cr)
Input Number
External Input
Data
0
0
0
0
DTV
0
0
0
1
Analogue
0
0
1
0
AV
0
1
0
0
Component
0
1
1
0
RGB
0
1
1
1
1
0
0
0
1
0
0
1
1
0
1
0
Input Number
HDMI
Data
0
0
0
0
Input1
0
0
0
1
Input2
0
0
1
0
Input3
0
0
1
1
Input4
Ack
(b)( )([Set ID])( )(OK/NG)(Data)(x)
9
Record the model number and serial number of the
Signage.
Refer to the label on the back cover and quote this
information to your dealer when requiring any service.
MODEL
SERIAL No.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising