LG LBNC0216QC Owner's manual

OWNER'S MANUAL
IMPORTANT
Please read through this manual. It contains valuable
information about your air conditioner. This manual may
help save time and money by explaining proper product
maintenance and preventing improper use.
PRECAUTIONS
Pay close attention to precautions in order to prevent
potential hazards and damage from misuse or improper
installation. LG is not responsible for any damages caused
by misuse of the product.
ENGLISH
LG
Low Static Hide Away Type Air Conditioner LG
Low Static Hide Away Type Air Conditioner Owner's Manual
TABLE OF CONTENTS
F or Your Records
Write the model and serial numbers here:
Model #
Serial #
1. Safety Precautions
You can find them on a label on the side of each unit.
2. Operating Instructions
Dealer's Name
3. Care and Maintenance
Date Purchased
4. Before you call for service
R ead This Manual
Inside you will find many helpful hints on how to use
and maintain your air conditioner properly. Just a little
preventive care on your part can save you a great
deal of time and money over the life of your air
conditioner.
You'll find many answers to common problems in the
chart of troubleshooting tips. If you review our chart of
Troubleshooting Tips first, you may not need to call
for service at all.
CAUTION
• Contact the authorized service technician for repair
or maintenance of this unit.
• Contact the installer for installation of this unit.
• The air conditioner is not intended for use by young
children or invalids without supervision.
• Young children should be supervised to ensure that
they do not play with the air conditioner.
• When the power cord is to be replaced, replacement
work shall be performed by authorized personnel
only.
• Installation work must be performed in accordance
with the national wiring standards by authorize d
personnel only.
2
Safety
Precautions
Precautions
Incorrect operation due to ignoring instructions will cause harm or damage, the seriousness of which is
indicated by the following symbols.
WARNING
This symbol shows the possibility of death or serious injury.
CAUTION
This symbol indicates the possibility of injury or damage to property.
ENGLISH
To prevent injury and property damage, follow these instructions.
Never Do This
Always Do This
Installation precautions
WARNING
WARNING
n
Do not install, remove and reinstall the unit by yourself.
• Improper installation will cause water leakage, electrical shock, or fire. Please consult
authorized dealer or specialist for the installation work. Please note fault caused by improper
installation is not covered by warranty.
• Unit must be installed in an easily accessible area. Any additional cost required to hire a
special equipment to service the unit will be the responsibility of the customer.
WARNING
WARNING
Do not damage or use an
unspecified power cord.
Do not operate switches
with wet hands.
• It will cause electrical shock or fire.
• It may cause electrical shock.
• If the supply cord is damaged, it must be
replaced by the manufacturer or its
service agent or a similarly qualified
person in order to avoid a hazard.
Do not operate or stop the
unit by inserting or pulling
out the power plug.
• It will cause electrical shock or
fire due to heat generation.
Do not insert your finger or
stick, etc. into the air inlet/air
outlet.
• Since the fan rotates at high
speed, this may cause an injury
or damage the unit.
Plug in the power plug
properly.
• Otherwise, it will cause
electrical shock or fire due to
heat generation.
Do not expose the skin to
cool air directly for a long
time.
• This could damage your health.
When an abnormality (smell of burning, etc)
occurs, stop the air conditioner, and
turn off the breaker.
Repair or relocation should not be done by the
customer.
• If the unit continues to be operated in an abnormal
condition, it may cause a fire, trouble, etc. In this
case, consult your dealer.
• If this is done in correctly, it may cause a fire,
electric shock, injury by dropping of the unit, water
leakage, etc. Consult your dealer.
3
CAUTION
CAUTION
• Contact the authorized Service technician for repair or maintenance of this unit.
• Contact the installer for installation of this unit.
• The air conditioner is not intended for use by young children or infirm persons without
supervision.
• Young children should be supervised to ensure that they do not play with the air conditioner.
CAUTION
CAUTION
Do not clean the air
conditioner with water.
Ventilate well when used
together with a stove, etc.
When the unit is to be
cleaned, switch off, and turn
off the breaker.
l
Water may enter the unit and
l
An oxygen shortage may occur. l
Since the fan rotates at high
degrade the insulation. It may
speed during operation, it may
cause an electric shock.
cause an injury.
Do not put a stove, etc.
where is exposed to direct
air flow.
When the unit is not going to
be used for a long time, turn
off the breaker.
Do not step on the outdoor
unit and do not put anything
on it.
l
It may cause imperfect
l
It may cause an injury.
l
It may cause an injury through
combustion.
dropping or falling down.
Do not operate for a long
time in high humidity, e.g.
leaving a door or window
open.
Do not step onto an unstable
bench when
attaching/detaching the
panel.
Do not use for special
purposes.
l
In the cooling mode, if it is
l
It may case an injury, etc. by
l
Do not use this air conditioner to
operated in a room with high
falling down.
preserve precision devices, food,
humidity (80%r.h. or more) for a
animal, plants and art objects.
long time, water condensed in
It may cause deterioration of
the air conditioner may drop and
quality, etc.
may wet and spoil furniture, etc.
If the supply cord is damaged, it
must be replaced by a special cord
or assembly available from the
manufacturer of its service agent.
When the air filter is to be
removed, do not touch the
metal parts of the indoor unit.
l
If will cause electrical shock or
l
It may cause an injury.
fire.
4
Operating
Instructions
Operating Instructions
LG Low Static Unit (H AT) Rem ote
Set Temp (Up/Down)
25
TEMP
DOWN
UP
HI
MED
MODE
FAN
LOW
COOL
TIMER
Fan Speeds
Mode
Quick Start
QUICK
Timer (On/Off)
FAN
TIMER
Power (On/Off)
POWER
Functions
1.
2.
3.
4.
5.
6.
7.
8.
Power (On/Off)
Timer (On/Off)
Set Temp (Up/Down)
Fan Speed (2)
a) High & Medium Speed (common)
b ) Low Speed
Mode
Quick Start
Set Temp. Display
7 Segment Display
5
ENGLISH
Name and Function of Remote Controller
Functions of MICOM
KEY & MODE
UNIT OPERATION STATE
ON / OFF
– Start in Previous Mode with previous settings when switched ON/OFF
from Power Button.
Cooling Mode
– In this Mode Cool LED will glow. In this mode 2 Fan Speeds, Timer and
Quick Start option available
Temp - Setting range 16~32°C, you can set the temp with increase/decrease
keys. 7-segment display shows the set temperature.
Cooling Cycle
COMP:OFF
PREVIOUS STATE
COMP:ON
MODE 1
MODE 2
MODE 3
ROOM TEMP
24.5°C
25°C
SET-0.5 SET TEMP
25.5°C
SET +0.5
– After compressor stops, it takes 2 min. 58 sec. ± 2 to restart.
6
Functions of MICOM
FAN
OPERATION
MODE
ENGLISH
KEY & MODE
UNIT OPERATION STATE
- Pressing‘Fan Operation’ stops the compressor and outdoor fan motor.
Fan Mode led will Glow
Three speed low, medium and high speed , corresponding LED (fan speed) will
glow. We can't change Set Temperature in this mode.
on 7 segment led Display for the High speed will be F3
Medium speed F2
}
Common speed
Low Speed F1
Timer option is available in this mode.
QUICK START - ‘Quick Start’ will function accordingly when the machine is switched OFF from
Power Button and when again switch ON then after 1 min ± 10 sec.
If we press "Quick" button then it will start the compressor immediately.
l
Don't operate it by changing the modes in running condition and then
checking the quick function, it will take around 3 min to start the
compressor.
7
Functions of MICOM
KEY & MODE
UNIT OPERATION STATE
TIMER
SETTING
- 1 hr ~ 12 hr Timer Setting step of 1 hour.
ON
TIMER
- Available when unit OFF.
- ON timer & OFF timer available in operation mode. Timer LED will glow in the
timer mode.
- Press 'Timer Button' Timer Key. Set the time hours by pressing the
increase/decrease keys.
- It starts counting time 5 sec after Timer was set.
7 segment displays the 1 to 12 nos. during the setting of timer.
After timer set will goes off.
- Unit starts at scheduled time with previous running condition.
OFF
TIMER
- Available when unit ON.
CANCEL
TIMER
- Press 'Timer Key Button' up to 0 hr setting. Timer will cancel.
If power fails during this period it will restore the operation for the remaining
time period.
Time store in the EEPROM is after every 15 minutes, however this much time
will lost in the power fail condition.
- Press 'Timer Set Button' Timer key.
7 segment shows the 1 to 12 no. in the setting after the timer setting it will
display the set temp in case of cool mode or F1 ~ F3 in case of Fan mode.
8
Functions of MICOM
ERRORS
UNIT OPERATION STATE
- In case of sensor faulty: 7 segment display shows the ‘E2’ in flashing mode
and unit will not take start.
Faults: short, or cut.
* (To overcome this we have to switch OFF the machine from mains Power Supply
and then connect new thermistor and then switch ON the Power Supply mains)
EEPROM failure: in case of EEPROM fails the display shows“E1” in flashing mode.
In this case unit will operate but in case of power fails the machine will not take start,
and after supplying mains power supply it shows "E1" which shows EEPROM failure
until it is manually pressed by Power Button, which starts the machine.
The machine will run in default mode.
1) Temp 22°C,
2) Cool mode,
3) High Speed
* (To overcome this we have to replace by new remote in field for the solution of
memory backup).
9
ENGLISH
KEY & MODE
Operation Mode
There are two Operations in airconditioner.
COOL
FAN
Operation Procedure
Operation procedures of airconditioner
3
1st
Power [ On/Off ]
To switch on/off the airconditioner
25
TEMP
DOWN
UP
HI
2nd
Operation Mode Selection Button
MED
To select the cool/fan mode
LOW
COOL
MODE
TIMER
FAN
4
2
QUICK
FAN
TIMER
3rd
Room Temperature Setting Buttons
4th
Indoor Fan Speed Selection Button
1
POWER
To increase / decrease the set temperature
To select the fan speed - High / Low
10
Operation Details
• Cooling Operation Mode
Helpful information
Airflow speed and cooling capacity.
The cooling capacity indicated in the specification is
the value when the fan speed is set to high, and the
capacity will be lower at low or medium fan speed.
High fan speed is recommended when you wish to
cool the room quickly.
• After main power is on, Fan will start 7 seconds later.
11
h
Hig ed
e
p
S
ENGLISH
When the room temperature is higher than the set temperature, it operates in cooling mode at the set
temperature, the set fan speed, and then it will be in automatically turn off when the room temperature
reaches the set temperature +0.5°C.
Care and
maintenance
Care and maintenance
Caution: Before performing any maintenance, turn off the main power to the system.
Indoor Unit
Never use any of the followings:
q
Grille, Case, and Remote Control
q
Turn the system off before cleaning. To clean,
• Water hotter than 40°C
Could cause deformation and/or
wipe with a soft, dry cloth. Do not use bleach or
discoloration.
abrasives.
Note:
• Volatile substances
Could damage the surfaces
Supply power must be disconnected before
of the air conditioner.
cleaning the indoor unit.
SI
Be
Air filters
n zene
N NER
SCO
U RIN G
C LB
A R GER
1
Clean the filter with a vacuum or warm, soapy
water.
• If very dirty, wash with a solution of
detergent in lukewarm water.
• If hot water (50°C or more) is used, filter
may be deformed.
2
After washing with water, dry well in the shade.
3
Re-install the air filter.
Air Filter
The air filters behind Indoor unit
(the suction side) should be checked and cleaned
once every 2 weeks or more often if necessary.
Air filters
Indoor Unit Dimensions (mm)
LB-C0216QC 01
25K BTU/h
B
C
927 897 390
D
E
H
I
85 560 748 232
Slope 5-8 mm
Dimension
No. of
A
IDU Capacity
E
Model
B
16
12
Outdoor Unit
ENGLISH
The heat exchanger coils and panel vents of the
outdoor unit should be checked regularly. If clogged
with dirt or soot, the heat exchanger and panel vents
may be professionally steam cleaned.
Note:
Dirty or clogged coils will reduce the operating
efficiency of the system and cause higher
operating costs.
Outdoor Unit
D
H
W
(Rear)
(Side)
Air intake
vents
Control Cover
Connecting Wire
Air outlet
vents
Connection Pipe
Drain Hose
2.1 TR
Indoor Unit
Remote Controller
Model
LB-C0216QC
Dimension
No. of
IDU Capacity
01
25K BTU/h
Outdoor Unit
Indoor Unit
W
D
H
W
D
H
870
320
655
980
565
300
13
When the air conditioner is not going to be used for a long time.
When the air conditioner is to
be used again.
When it is not going to be used for
a long time.
1
n
Check that the air inlet and outlet of the
indoor/outdoor unit are not blocked.
Operate the air conditioner on Air circulation
mode (Refer to page 15) for 2 to 3 hours.
• This will dry out the internal parts.
2
Turn off the circuit breaker.
Helpful information
CAUTION
CAUTION
The air filters and your electiric bill.
If the air filters become clogged with dust, the
cooling capacity will drop, and 6% of the
electricity used to operate the air conditioner will
be wasted.
Turn off the circuit breaker when the air conditioner
is not going to be used for a long time.
Dirt may collect and may cause a fire.
Operation Tips
Do not overcool the room.
This is not good for the health
and wastes electricity.
Clean the air filter regularly.
Blockages in the air filter
reduce the airflow and lower
cooling and dehumidifying
effects. Clean at least once
every two weeks.
Keep blinds or curtains
closed.
Do not let direct sunshine
enter the room when the air
conditioner is in operation.
Ventilate the room
occasionally.
Since windows are kept
closed, it is a good idea to
open them and ventilate the
room now and then.
14
Make sure that the doors
and windows are shut tight.
Avoid opening doors and
windows as much as possible
to keep the cool air in the
room.
Troubleshooting
Tips
Before you call for service...
Check the following points before requesting repairs or service.... If the malfunction persist, please contact your
dealer.
Case
The air conditioner does not
operate.
The room has a peculiar odor.
It seems that condensate is
leaking from the air Conditioner.
Air conditioner does not operate
for about 3 minutes when restart.
Does not cool or heat effectively.
The air conditioner operation is
noisy.
Crack sound is heard.
Remote control display is faint, or
no display at all.
Explanation
See page
Have you made a mistake in timer operation?
8
On first starting, the indoor unit operates in
fifteen seconds.
l
Has the fuse blown or has the circuit breaker
been tripped?
l
Check power supply for single/reverse phase,
voltage imbalance.
l
Check that this is not a damp smell exuded by
the walls, carpet, furniture or cloth items in the
room.
l
Condensation occurs when the airflow from the
air conditioner cools the warm room air.
l
This is the protector of the mechanism.
l
Wait about three minutes and operation will
begin.
l
Is the air filter dirty? See air filter cleaning
12
instructions.
l
The room may have been very hot when the
room air conditioner was first turned on. Allow
time for it to cool down.
l
Has the setting temperature been set
incorrectly?
l
Are the indoor unit's air inlet or outlet vents
obstructed?
l
For a noise that sounds like water flowing.
-This is the sound of freon flowing inside the air
conditioner unit.
l
For a noise that sounds like the compressed air
releasing into atmosphere.
-This is the sound of the dehumidifying water
being processed inside the air conditioning
unit.
l
This sound is generated by the
expansion/contraction of the inlet grille, etc. due
to changes of temperature.
l
Has the circuit breaker been tripped?
l
l
NOTE
WATER RESISTANT: The outdoor side of this appliance is WATER RESISTANT.
The indoor side is not water resistant and should not be exposed to excess
water.
15
ENGLISH
Troubleshooting Tips! Save time and money!
P/No.: 3828A33011C
After reading this manual, keep it in a place easily accessible to the user for future reference.