- Home
- Domestic appliances
- Climate control
- Split-system air conditioners
- LG
- LMNC186TEC0
- Owner's manual
LG LMNC126TEC0 Owner's manual
Add to my manuals34 Pages
The LG LMNC126TEC0 Multi-Type Air Conditioner is a versatile and powerful cooling solution for various indoor spaces. With its cassette-type design, it seamlessly integrates into drop ceilings, providing efficient air distribution and temperature control. The unit's compact size and sleek appearance make it suitable for both residential and commercial applications.
advertisement
▼
Scroll to page 2
of 34
website http://www.lgservice.com LG LG Multi-Type Air Conditioner(Cassette Type) OWNER'S MANUAL Prior to installation, this air-conditioning unit must be submitted for approval by the utility service which provides electricity (EN 61000-2, EN 61000-3 Norm). IMPORTANT ? Please read this owner's manual before ? installing and carefully operating your room and thoroughly air conditioner. Please retain this owner's manual for future reference after reading it thoroughly. P/No.: 3828A32001J Multi-Type Air Conditioner Owner's Manual TABLE OF CONTENTS FOR YOUR RECORDS Safety Precautions.........................3 Write the model and serial numbers here: Model # Prior to Operation ..........................8 Serial # You find them can label on a on the side of each unit. Dealer's Name Introduction ....................................9 Date Purchased Staple it to prove Electrical Operating Safety receipt to this page in the event you need date of purchase or for warranty issues. your ...........................10 Instructions.................11 READ THIS MANUAL Inside you will find many helpful hints on how to use and maintain your air conditioner properly. Just a little preventive care on of time and money Maintenance and Service ............30 your over you a great deal the life of your air conditioner. part can save You'll find many answers to common problems in the chart of troubleshooting tips. If you review our chart of Troubleshooting Tips first, you may not need to call for service at all. PRECAUTION ? Contact the authorized service technician for repair Contact the installer for installation of this unit. ? The air conditioner is not intended for ? ? Air Conditioner use by young children or invalids without supervision. Young children should be supervised to ensure that Multi-Type maintenance of this unit. ? ? 2 or they When do not the play with the air conditioner. power cord is to replacement work shall be be replaced, performed by authorized personnel only using only genuine replacement parts. Installation work must be performed in accordance with the National Electric Code by qualified and authorized personnel only. Safety Precautions Precautions Safety To prevent injury to the user or other people and property damage, the following instructions must be followed. Incorrect is operation due to ignoring instruction classified by the following indications. Meanings of symbols will cause harm or The seriousness damage. This symbol indicates the possibility of death or serious This symbol indicates the possibility of or damage. used in this manual are as Be Be injury injury. shown below. not to do. sure to follow the instruction. sure Installation Do not use a defective For electrical work, contact the dealer, seller, a qualified electrician, or an Authorized or underrated circuit breaker. Use this appliance on a dedicated circuit. ? There is risk of fire Always ground the product. Service Center. or electric ? shock. Do not disassemble product. or repair There is risk of fire the ? There is risk of fire or electric shock. or electric shock. Install the cover panel and the Always of control box install dedicated a circuit and breaker. Use the correctly breaker or rated fuse. securely. ? There is risk of fire shock. or electric ? Improper wiring may cause fire or or installation electric shock ? There is risk of fire or electric shock. Owner's Manual 3 Safety Precautions Do not modify or extend the Do not power cable. ? There is risk of fire or electric Be cautious when install, remove, or re-install the unit by yourself (customer). ? shock. There is risk of fire, electric shock, explosion, or and ? injury. installing Sharp edges could cause injury. Be especially careful of the case edges and the fins on the condenser and For installation, always dealer ? or an contact the Do not install the Authorized Service Center. There is risk of fire, electric shock, explosion, or product Be on a defective installation stand. ? injury. It may injury, accident, damage to the product. cause the unpacking product. sure evaporator. the installation area does not deteriorate with age. or ? If the base collapses, the air conditioner could fall with it, causing property damage, product failure, and personal injury. Operation Do not let the air conditioner ? long time when the humidity that power cable could not be pulled out or and damaged during operation. a door or a run for Take a is very high window is left open. Moisture may condense and wet or damage furniture. ? There is risk of fire or electric shock. 4 Multi-Type Do not ensure There is risk of fire or electric place anything on the power cable. ? There is risk of fire or electric shock. shock. Do not Donotplaceaheateror other appliances near the power cable. ? There is risk of fire shock. Air Conditioner to touch(operate) the product with wet hands. Donotplugorunplugthe power supply plug during operation. ? care or electrical ? There is risk of fire and electric shock. Safety Precautions Do not allow water to into electric Do not store run parts. gas or or use flammable combustibles near Do not the It may cause There is risk of fire, failure of the product, or electric ? There is risk of fire or failure of the ? in product tightly closed space long time. product. ? use Oxygen deficiency for could a a occur. product. shock. Gasolin When flammable gas leaks, turn off the gas and open a strange sounds, or small or smoke comes from product. Turn Stop operation and window for ventilation the breaker off remove before turn the ? Do not use switches the product telephone If on. or turn power ? off. on or There is risk of explosion or physical injury, shock, or product failure. Ventilate the ? it or the hurricane. If possible, product from the window before the hurricane arrives. or ? There is risk of failure of When the product is soaked (flooded or submerged), contact property damage, product, or electric shock. electric shock. an Be cautious that water could not enter the product. Authorized Service Center. ? There is risk of fire shock. product from time to together with a stove, There is risk of fire or fire There is risk of operating supply cable. fire. grill of the product during operation. (Do not touch the electrostatic filter, if the unit is so equipped.) electric disconnect the There is risk of electric shock Do not open the inlet ? or in storm close the window or electric ? There is risk of or time when fire, electric shock, product damage. Turn the main power off when maintaining the product. etc. ? cleaning or There is risk of electric shock. Owner's Manual 5 Safety Precautions When the product is not be used for time, disconnect the Take long power supply plug or a care on or to ensure that nobody could step fall onto the outdoor unit. turn off the breaker. There is risk of ? unintended product damage operation. or failure, ? or This could result in personal injury and product damage. Installation Always check for gas (refrigerant) leakage after installation or repair of product. Low refrigerant levels failure of product. ? may cause Install the drain hose to ensure away ? that water is drained properly. A bad connection may water Keep level even when installing the product. ? cause leakage. To avoid vibration or water leakage. 90° Do not install the noise or could damage the neighborhoods. It may ? product where the Use two hot air from the outdoor unit cause a problem for your or more Do not install the people to product where it will be exposed to wind (salt spray) directly. lift and transport the product. ? Avoid personal injury. ? It may cause corrosion on sea the product. Corrosion, particularly on neighbors. the condenser and could product operation. cause inefficient evaporator fins, malfunction or Operation Do not expose the skin directly to cool air for long periods of time. (Don't sit in the product for special purposes, such as preserving foods, works of art, etc. It is a consumer air conditioner, not a precision refrigeration system. draft.) This could harm to your health. ? Do not ? use Thereisriskof damage loss of 6 Multi-Type Air Conditioner the or property. Safety Precautions Do not block the inlet Use or outlet of air flow. soft cloth to clean. a Do not use It may cause product failure. ? etc. There is risk of damage to the product. or fire, electric shock, the plastic parts of Wax Donotsteponorput anyting on the product. (outdoor units) ? Always ? personal injury product. ? A dirty insert the filter efficiency Do not drink the water Use drained from the when product. a malfunction firm stool or ? There are that could ladder sanitary and could serious health issues. Do not Do not cause Be careful and avoid of the personal recharge or disassemble the dispose of batteries in a fire. They may burn or explode. batteries in the same ? new ones type. Do new not mix batteries or types of batteries. There is risk of fire or explosion injury. batteries. If the skin not ? cause moving parts personal injury. remote control with cleaning or maintaining the product. ? and sharp Replace the all different It is not other or old and ? or objects through the air inlet or outlet while the product is operated. of the air conditioner and could product damage. personal injury. Do not insert hands securely. filter reduces the cause There is risk of Thinner Clean the filter every two weeks or more often if necessary. There is risk of and failure of parts of the product when removing the air filter. They are very sharp! harsh detergents, solvents, ? Do not touch the metal ? liquid from the batteries gets onto your or clothes, wash it well with clean water. use Do the remote if the batteries have leaked. The chemicals in batteries could cause burns or other health hazards. Owner's Manual 7 Prior to Operation Prior to Preparing 1. Contact 2. Plug for Operation operation installation an in the power specialist for plug properly. installation. 3.Useadedicatedcircuit. 4. Do not use an extension cord. 5. Do not 6. If the start/stop operation by plugging/unplugging the power cord. cord/plug is damaged, replace it with only an authorized replacement part. Usage 1. Being exposed to direct airflow for an extended your health. Do not expose occupants, pets, periods of time. or period of time could be hazardous to plants to direct airflow for extended 2. Due to the 3. possibility of oxygen deficiency, ventilate the room when used together with stoves or other heating devices. Do not use this air conditioner for non-specified special purposes (e.g. preserving precision devices, food, pets, plants, and art objects). Such usage could damage the items. Cleaning and maintenance 1. Do not touch the metal when handling sharp 2. Do not use parts of the unit when removing the filter. Injuries metal can occur edges. water to clean inside the air conditioner. Exposure to water insulation, leading to possible electric shock. 3. When cleaning the unit, first make sure that the power and breaker can destroy the The fan rotates at the unit's power is 8 repair and Multi-Type turned off. high speed during operation. There is a possibility of injury accidentally triggered on while cleaning inner parts of the unit. a very Service For are maintenance, Air Conditioner contact your authorized service dealer. if Introduction Introduction Symbols used in this Manual This symbol This symbol alerts you to the risk of electric shock. alerts you to hazards that could air conditioner. NOTICE This symbol indicates special cause harm to the notes. Features WARNING: This appliance should be installed in accordance with national wiring regulations. This guide acts as a guide to help to explain product features. Heat Pump Model Anti-bacteria Signal Receptor Air Intake Cooling Air Outlet Model Remote Controller Signal Receptor Owner's Manual 9 Electrical Safety Electrical Safety WARNING: This appliance To minimize the risk of electric shock, you must be must properly grounded. alway plug into a grounded oulet. Preferred method Ensure proper ground exists before use WARNING: Do not cut or remove the grounding prong from the power wire. WARNING: adapter ground terminal to the wall receptacle cover screw does not ground the appliance unless the cover screw is metal and not insulated, and the wall receptacle is grounded through the house wiring. Attaching the WARNING: If you have any doubt whether the air conditioner is grounded, have the wall receptacle and circuit checked properly a qualified 10 Multi-Type electrician. Air Conditioner by Operating Operating Instructions Instructions Indoor Unit Indoor Unit Heat Pump Model Anti-bacteria Signal Receptor Air Intake Cooling Air Outlet Model Remote Controller Signal Receptor Receives the signals from the remote control. (Signal receiving sound: two short beeps or one long beep.) Operation Indication Signal Receptor Lamps On/Off : Lights Filter : Lights up operating after 2400 hours from the time of first during Sign up during unit. the system operation. (Refer to page Timer : Lights Defrost Mode : Lights up during Defrost (Heat pump model only) Mode Outdoor Unit : Lights up during outdoor (Cooling model only) unit : Operation procedures Operation Forced Operation up Timer 23.) operation. or Hot Start operation. operation. when the remote control can't be used. Heat pump model: Cassette Type Air Conditioner for cooling and Cooling model: Cassette Type Air Conditioner for cooling heating Owner's Manual 11 Instructions Operating Name and Function of Remote Controller Remote Controller AUTO SWING OPERATION SET TEMP FAN SPEED Room Temp HI MED LO AUTO JET SUB FUNCTION Heater Preheat Defrost Humidify Filter Out door Heat 1 Pump Model Time Timer On Set Operation unit Program set Off010305070911131517192123 Time no. 6 3 17 2 10 11 12 Timer Cancel Program Week 13 14 15 Cooling 5 Holiday Model 4 Plasma 7 Set/Clr Hour Min 8 9 RESET 16 18 1. 9. Plasma Air Clean Button Operation display Displays the operation conditions. 10. Timer Cancel Button 2. On/Off Button Operation Used to cancel the timer. starts when this button is stops when the button is 3. Set pressed, pressed again. and 11. Timer Set Button Used to set the timer when the desired time is Temperature Button Used to set the obtained. temperature when the desired temperature is obtained. 4. FAN room 12. Week Button Used to set Button Operation Used to circulate air without cooling or 13. 14. & Jet Cool Button Speed Used to set the desired fan speed and select Jet Operation Mode Selection Button Used to select the ? ? ? ? operation mode. Cooling Operation Mode Soft Dry Operation Mode Heating Operation Mode(except cooling model) Auto Operation Mode 7. Auto Swing Used to 8. Room swing Button Temperature Checking room Button Holiday weekly timer. Button Used to set a holiday of the week. Used to set the time of the time in the weekly timer day and change the Function. 16. Set and Clear Button Used to set and clear the weekly timer. 17. Swirl Button Used to select swirl mode. 18. Reset Button up and down. Used to check the day of the week. 15. Time Set Button cool mode. 6. Program a Used to set the heating. 5. Fan (optional) Used to set the current time and clear the Button temperature. Display temperature can be different from actual room temperature if the remote installed at the place where sun-rays are falling directly or the place nearby heat 12 Multi-Type setting time. Air Conditioner controller is source. Operating Instructions Wireless Remote Controller (optional) This air-conditioner is wireless remote equipped with wired remote controller basically. But if you want to be available with controller, you pay for it. 1. START/STOP BUTTON Signal transmitter Operation starts when this button is pressed again. button is and pressed stops when the 2. OPERATION MODE SELECTION BUTTON Used to select the operation mode. 3. ROOM TEMPERATURE SETTING BUTTONS Used to select the room temperature. 4. INDOOR FAN SPEED SELECTOR Used to select fan speed in four steps low, medium, high and CHAOS. 5. JET COOL 5 Used to start stop the speed cooling/heating. (Speed cooling/heating operates super high fan speed.) 1 6 or 6. CHAOS SWING BUTTON 3 Used to stop or start louver movement and set the desired up/down airflow direction. 4 7. ON/OFF TIMER BUTTONS Used to set the time of 10 27 CANCEL Used to SET OFF 11 and stopping operation. 8. TIME SETTING BUTTONS 9 ON starting adjust the time. 9. TIMER SET/CANCEL BUTTON 12 8 Used to set the timer when the desired time is obtained and to cancel 13 the Timer operation. 10. SLEEP MODE AUTO BUTTON Used to set 15 14 Sleep Mode Auto operation. 11. AIR CIRCULATION BUTTON Used to circulate the room air without cooling or heating. 12. ROOM TEMPERATURE CHECKING BUTTON Used to check the Flip-up door (opened) 13. room temperature. PLASMA(OPTIONAL) Used to start or stop the plasma-purification function. 14. RESET BUTTON Initialize remote controller. 15. 2nd F Button Used The wireless remote controller do not CAUTION:of handling ? Aim at the ? The remote control ? Be ? Do not ? Do not ? sure signal receiver that there on printed the Remote Controller the wired remote controller can in blue at the bottom of buttons. operate the swirl mode. be received at so as to operate. a drop or throw the remote controller. place the remote controller in a location exposed any other heat Block a strong modes distance of up to about 7m. obstructions between the remote controller and the signal are no prior to using to direct sunlight, signal receptor. or near the heating unit, or source. light over the signal receptor with a curtain or etc. so as to prevent the operation. (ex:electronic quick start, ELBA, inverter type fluorescent lamp) abnormal Owner's Manual 13 Operating Instructions Set the Current Time and 1 Press the ' ' a day of the Week button. Hour Each time the button is You can pressed, the number is changed from 00 to 23. set the number of the current hour. AUTO SWING OPERATION SET TEMP FAN SPEED SUB FUNCTION Hour Time 2 Press the ' ' button. Min Each time the button is You can pressed, the number is increased from 00 to 59. set the number of the current minute. AUTO SWING OPERATION SET TEMP FAN SPEED SUB FUNCTION Min Time 3 Press ' Week ' button. Each time the button is You can set the pressed, a day of the week is shifted from sunday to saturday. day of the week. AUTO SWING Week OPERATION SET TEMP FAN SPEED SUB FUNCTION Time 4 Press the ' RESET ' button. If you want to reset the current time and a day of the week, AUTO SWING RESET 14 Multi-Type Air Conditioner click the Reset button. OPERATION SET TEMP FAN SPEED SUB FUNCTION Operating Instructions Weekly Program Setting 1 Press the Program button. The remote controller is displayed like below. Then ' Program AUTO SWING Program ' ',' set OPERATION and '01' is blinked. SET TEMP FAN SPEED SUB FUNCTION Program set Time 010305070911131517192123 Week 2 ' Press the Select the ' button. Monday. Week AUTO SWING OPERATION SET TEMP FAN SPEED SUB FUNCTION Program set Time 3 010305070911131517192123 Change the timer setting until the desired time is set. After you select a time, push the SET/CLR button once or one more For time. Example Hou if the air-conditioner is turned on is (black bar indicates turn-on, white bar indicates turn-off.) If you follow the above procedure, you can set timer for turning or and off in all of the week. as Min from 6 to 8 and from 13 to 22 and turned off at other time monday, display SET/CLR AUTO SWING OPERATION SET TEMP FAN SPEED SUB FUNCTION follows. Time 010305070911131517192123 If you don't set the 4 setting. If you weekly program again after setting the weekly program, it is same the previous want to keep the weekly program for only a week follow the next procedure. Press the "CANCEL" button and "SET/CLR" button 1) toggled AUTO SWING 2) Then the display will be like befor. OPERATION SET TEMP Detach your Then simultaneously. FAN SPEED SUB FUNCTION AUTO SWING finger from buttons at the moment that it the weekly program is kept for only one week. OPERATION is SET TEMP displayed FAN SPEED the SUB FUNCTION figure. Owner's Manual 15 Instructions Operating Holiday Setting If Tuesday is a holiday in this week, you may set a holiday. AUTO SWING OPERATION SET TEMP FAN SPEED SUB FUNCTION Program Press the Program button. Program set Time Week 010305070911131517192123 AUTO SWING OPERATION SET TEMP FAN SPEED SUB FUNCTION Press the Week button. Select the Tuesday. Program set Time 010305070911131517192123 Holiday AUTO SWING Press the Holiday displayed holiday. The outside Timer SET TEMP FAN SPEED SUB FUNCTION button. Then the remote controller will be You OPERATION rectangular means cannot set the weekly program for a ' '. Time 010305070911131517192123 holiday. Setting (Delay start/Pre-set stop) This function is used to turn on or turn off after several hours. Cancel Press the Timer button to turn Timer on or off. Hou Change the timer setting Min until the desired time is set. Cancel If you want to cancel the timer setting, press the Cancel button. AUTO SWING ? When the air conditioner is turned is turned on OPERATION SET TEMP FAN SPEED SUB FUNCTION off, the air conditioner after 8 hours. Timer On Time 010305070911131517192123 AUTO SWING ? OPERATION SET TEMP FAN SPEED SUB FUNCTION When the air conditioner is turned on, the air conditioner is turned off after 5 hours. Timer Off Time Self-diagnosis ' 16 Function CH' will flash in the remote controller Then Multi-Type please 010305070911131517192123 contact your dealer. Air Conditioner display when a problem occurs. Operating Operation Instructions Mode Cooling Mode Cooling Mode Soft Dry Mode Soft Mode Heating Mode Dry Auto Mode (Cooling Model) Auto Mode (Heat Pump Model) Operation 1st Procedure On/Off Button AUTO SWING OPERATION SET TEMP Room Temp FAN SPEED HI MED LO AUTO JET SUB FUNCTION Heater Preheat Defrost Humidify Filter Out door Time Timer On 2nd Set Operation Mode Selection Button Operation unit Program set Off010305070911131517192123 no. Time 3 1 3rd Room Temperature Setting Button Timer Cancel Program Week 42 Holiday SET/CLR Hour 4th Indoor Fan Speed Min RESET Selection Button Owner's Manual 17 Operating Instructions Cooling Operation 1 Press the On/Off Button. 2 Select Mode Cooling Operation. Press the Operation Mode Selection Button. Each time the button is the pressed, operation mode is shifted in the arrow direction. HEAT PUMP MODEL Operation Display AUTO SWING OPERATION SET TEMP AUTO SWING FAN SPEED OPERATION SET TEMP FAN SPEED AUTO SWING OPERATION SET TEMP FAN SPEED HI AUTO SWING OPERATION SET TEMP FAN SPEED HI AUTO LO Soft Cooling Operation Dry Operation Auto Heating Operation Operation COOLING MODEL Operation Display AUTO SWING OPERATION SET TEMP FAN SPEED SUB FUNCTION AUTO SWING OPERATION SET TEMP FAN SPEED SUB FUNCTION AUTO SWING OPERATION SET TEMP FAN SPEED HI SUB FUNCTION AUTO LO Soft Cooling Operation 3 Set the temperature lower than the AUTO SWING OPERATION Auto Dry Operation SET TEMP FAN SPEED ? SUB FUNCTION HI room temperature. Operation Thetemperaturecanbeset withinarangeof18°C~30°C by 1°C. To increase the Temperature. To decrease the 4 Set the fan Temperature. speed. Operation Display AUTO SWING OPERATION SET TEMP FAN SPEED HI AUTO SWING OPERATION SET TEMP FAN SPEED AUTO SWING OPERATION SET TEMP FAN SPEED AUTO SW NG OPERATION SET TEMP FAN SPEED AUTO SWING OPERATION SET TEMP FAN SPEED AUTO MED JET LO ? ? ? Select the fan speed in five steps-high, auto, power jet, low, medium. The display shows high fan speed. Each time the button is pressed, the fan speed mode is shifted. During Cooling operation, pressing operation mode.(Refer to p26.) 18 Multi-Type Air Conditioner the fan speed button can be changed Jet Cool Operating Soft 1 Mode Dry Operation This mode dehumidifies without Instructions overcooling. Press the On/Off Button. Select Soft 2 Press the Dry Operation. operation Mode Selection Button. Each time the button is pressed, the operation mode is shifted in the arrow direction. HEAT PUMP MODEL Operation Display AUTO SWING OPERATION SET TEMP AUTO SWING FAN SPEED OPERATION SET TEMP FAN SPEED AUTO SWING OPERATION HI SET TEMP FAN SPEED AUTO SWING OPERATION SET TEMP FAN SPEED HI AUTO LO Soft Cooling Operation Dry Operation Heating Operation Auto Operation COOLING MODEL Operation Display AUTO SWING OPERATION SET TEMP FAN SPEED SUB FUNCTION AUTO SWING OPERATION SET TEMP FAN SPEED SUB FUNCTION AUTO SWING OPERATION HI SET TEMP FAN SPEED SUB FUNCTION AU TO LO Cooling Operation Soft Dry Operation Auto Operation During Dry Operation. 3 ? The indoor fan is impossible speed because is automatically set to the low, so the shift of the indoor fan speed of already being set to the best speed for Dry Operation by Micom Control. Owner's Manual 19 Operating Instructions Mode Heating Operation 1 2 (Heat pump model only) Press the On/Off Button. Select Heating Operation. Press the Operation Mode Selection Button. Each time the button is pressed, the mode is shifted in the operation arrow direction. Operation Display AUTO SWING OPERATION SET TEMP FAN SPEED AUTO SWING OPERATION SET TEMP FAN SPEED AUTO SWING OPERATION SET TEMP FAN SPEED HI AUTO SWING OPERATION SET TEMP FAN SPEED HI AU TO LO Cooling Operation Set the 3 higher AUTO SWING temperature than the Soft Dry Operation OPERATION SET TEMP Auto Heating Operation FAN SPEED SUB FUNCTION ? HI Thetemperaturecanbeset within room by temperature. a range of 16°C~30°C 1°C. To increase the Temperature. To decrease the 4 Set the fan Operation Temperature. speed. Operation Display AUTO SWING OPERATION SET TEMP FAN SPEED AUTO SWING OPERATION SET TEMP FAN SPEED AUTO SWING OPERATION SET TEMP FAN SPEED AUTO SWING OPERATION SET TEMP FAN SPEED AU TO HI MED LO ? ? ? 5 Select the fan speed in four steps-high, Auto, low, medium. The display shows high fan speed Each time the button is pressed, the fan speed mode is shifted. This air-conditioner is set to the hot start control in AUTO SWING OPERATION SET TEMP FAN SPEED SUB FUNCTION HI Preheat order not to discharge the cold air during the heating operation. This time, the remote controller indicates 'Preheat'. 6 If the outdoor temperature is during the this air-conditioner is set to the heating operation, defrosting operation and the remote controller indicates 'Defrost'. 20 too low Multi-Type Air Conditioner AUTO SWING OPERATION SET TEMP FAN SPEED SUB FUNCTION HI Defrost Instructions Operating Auto Mode Operation 1 Press the On/Off Button. 2 To select Auto (Cooling model) Each time the Operation, press the Operation Mode Selection button. button is pressed, the operation mode is shifted in the direction of the arrow. COOLING MODEL Operation Display AUTO SWING OPERATION SET TEMP FAN SPEED SUB FUNCTION AUTO SWING OPERATION SET TEMP FAN SPEED SUB FUNCTION AUTO SWING OPERATION SET TEMP HI FAN SPEED SUB FUNCTION AUTO LO Soft Cooling Operation 3 The temperature and fan speed Auto Dry Operation Operation automatically set by the electronic controls based on the actual room temperature. If you want to change the set temperature, close the door on the remote control and press the Room Temperature Setting buttons. The cooler or warmer you feel, the more times (up to two times) you should press the button. The set temperature will then be changed. The temperature can be set within a range of -2~2by 1 level. AUTO SWING OPERATION SET TEMP are FAN SPEED SUB FUNCTION AUTO Cold Cool Proper Warm Hot To increase the (This Temperature. indication will be shifted to the initial Auto Mode Display state after 5 seconds.) To decrease the Temperature. During Auto Operation: You cannot switch the indoor fan already been set by the Fuzzy rule. If the system is not operating as desired, manually switch to another mode. The system will not automatically switch from the cooling mode to the heating mode, or from heating to cooling, it must be done by manually resetting. During Auto Operation, pressing the auto swing button makes the horizontal louvers swing up and down automatically. If you want to stop auto-swing, press the auto swing button again. speed. It has Owner's Manual 21 Operating Auto Instructions Mode Operation 1 Press the On/Off Button. 2 To select Auto (Heat pump model) Operation, press the Operation Mode Selection button. Eachtimethebuttonispressed,theoperationmodeisshiftedinthedirectionofthearrow. HEAT PUMP MODEL Operation Display AUTO SWING OPERATION SET TEMP FAN SPEED AUTO SWING OPERATION SET TEMP FAN SPEED AUTO SWING OPERATION SET TEMP HI FAN SPEED AUTO SWING OPERATION SET TEMP FAN SPEED HI AUTO LO Cooling Operation 3 The setting temperature canbechanged,when the set Soft Dry Operation ? AUTO SWING OPERATION SET TEMP FAN SPEED SUB FUNCTION Operation Thetemperaturecanbeset within range of 18°C~30°C with increment/decrement of AUTO temperature button is Auto Heating Operation a 1°C. pressed. To increase the Temperature. To decrease the Temperature. During Auto Operation: You can The system will automatically switch from the cooling mode cooling, 22 switch the indoor fan when you select Auto Multi-Type Air Conditioner speed. Operation mode. to the heating mode, or from heating to Operating FAN ? Operation Used to circulate room Instructions Mode air without cooling or heating. Press the On/Off Button. 1 2 Press FAN Operation Button. AUTO SWING OPERATION SET TEMP FAN SPEED SUB FUNCTION HI 3 Each time Fan Speed button is pressed, the fan mode is shifted in the speed direction. AUTO SWING OPERATION SET TEMP arrow FAN SPEED SUB FUNCTION HI ? Fan speed is Auto. ? Fan speed is high. AUTO SWING OPERATION SET TEMP FAN SPEED SUB FUNCTION AUTO SWING OPERATION SET TEMP FAN SPEED SUB FUNCTION AUTO MED ? Fanspeedismedium. ? Fan speed is low. AUTO SWING OPERATION SET TEMP FAN SPEED SUB FUNCTION LO Owner's Manual 23 Operating Instructions Comfort Operation ? It is the function for comfort ? The diagonal After two louvers minute, it is one with Swirl cooling/heating operation. opened opposite. are the more larger than the other louvers. T 111 Timer Program CTION Defrost Preheat Filter 31517192123 Cancel Week eater Humidify door Out Hour Min SET/CLR RESET 1 Press the On/Off Button. The unit will respond with a beep. AUTO SWING OPERATION SET TEMP FAN SPEED SUB FUNCTION HI 2 Press the Swirl Button to comfort Then it angle Timer Cancel Program Week 3 Holiday SET/CLR Hour 24 Min Multi-Type RESET Air Conditioner operate cooling or heating. will be changed the open of two horizontal louvers. To cancel the Swirl Button again. Mode, press the Swirl Operating Instructions Vane Control You can change the open angle to the 1 Press the On/Off Button. 2 Press the install situation. right arrow and auto swing button simultaneously for three seconds. Then the display will be toggled like before. Detach your finger from buttons at the moment that it is displayed "P0" in the operation display. Min 3 Swing button again. Then it will be changed the open angle (from P0 to P5) 4 Press the + Press the Auto right arrow button and Auto of two horizontal louvers. Swing button to finish the setting. + Min 5 Press the left arrow button and Auto to set the other two louvers. Next Swing button for three seconds procedure is the same before. in order + Hour 6 Although the air conditioner is turned If you want to set the default "P0". position, ON/OFF, the previous setting position is not changed you have to set the "P0". Because the default is the Owner's Manual 25 Operating Instructions Jet Cool Operation Mode 1 Press the On/Off button. The unit will respond with abeep. Select AUTO SWING OPERATION SET TEMP FAN SPEED SUB FUNCTION 2 JET Cooling Operation. Press the Fan speed button. Operation Display AUTO SWING OPERATION SET TEMP FAN SPEED AUTO SWING OPERATION SET TEMP FAN SPEED AUTO SWING OPERATION SET TEMP FAN SPEED AUTO HI JET AUTO SWING Timer OPERATION SET TEMP FAN SPEED AUTO SWING Cancel OPERATION SET TEMP FAN SPEED MED LO Program Week Holiday SET/CLR Hour Min RESET 3 To cancel the jet button the set button, again, or fan cool mode, press the fan speed temperature button, operation operation or button. or or NOTICE During the Jet Cool function at any moment, the A/C starts to blow the cool air at extremely high speed setting the room temp. automatically to 18°C. It is especially used to cool the temp. in the shortest time in a hot summer. In heating mode however, the Jet Cool function is room In order to return to the normal not available. mode from the Jet Cool mode, you just press either the operation mode selection button, fan speed button or temperature setting button or fan operation 26 Multi-Type button. Air Conditioner cooling Operating Auto Swing Mode Cancel Program Instructions 192123 Week Holiday Hour SET/CLR Min RESET 1 Press the On/Off button. 2 (Confirm the unit on operation.) Press the Auto Swing again the Swingbuttonto 3 Press button then the horizontal cancel the louvers Auto swing Swing Auto mode. up and down automatically. Child Lock Function This is the function that any children cannot used to the air-conditioner. Operation procedure AUTO SWING OPERATION SET TEMP FAN SPEED SUB FUNCTION 1. To set the Child-Lock Function Press the Timer button and Minute Set button for three seconds. Then the mode and it is operation mode shift to child lock displayed CL in the operation display. ' ' When you press any button in this time, the remote controller is not converted to any selected mode and the ' ' CL is displayed in the remote controller for about three seconds. But the Room in spite Temperature function is operated Timer Cancel of child lock mode. ogram Week 2. To cancel the Child-Lock Function Press the Timer button and Minute Set button for three Holiday SET/CLR Hour Min SET seconds. Then the child-lock mode is cancelled and the preselected mode is displayed in the remote controller. Owner's Manual 27 Operating Instructions PLASMA Purification Operation (Optional) 1 AUTO SWING OPERATION SET TEMP FAN SPEED SUB FUNCTION 2 HI Press the On/Off button. The unit will Open respond the door with on a beep. the remote control. Press the PLASMA air purifying operation ON/OFF button. Operation will start when Plasma the button is when the Timer Cancel Program Week pressed and stop button is pressed again. Holiday Plasma SET/CLR Hour Min 3 RESET Set the fan speed again control closed. You can with door of the remote select the fan speed in four steps-low, medium, high or Auto. Each time the button is pressed, the fan speed mode is shifted. Air purifying operation (PLASMA) with cooling, heating or any other operations. Tips sign LED sign lamp (LED) is ON. for Filter 1. Filter 2. If LED 3. After indicating cleaning filter the sign lamp 28 Multi-Type sign ON, clean the filter. filter, press the Timer button and thesametimefor3sec. Then filter is LED is OFF. Air Conditioner button of wired remote controller at Operating Forced Instructions Operation Operation procedures when the remote control can't be used. Press the tact switch (Forced operation) for 2 seconds. If you want to stop operation, press again the tact switch. In case the power comes on again after power failure on the Forced Operation mode, the operating conditions are automatically set as follows: During Forced Operation, the initial mode continues. Forced operation (Tact switch) Cooling Operating Indoor FAN mode Speed Setting Temperature Heat pump Model Model Room Temp. ≥ set Temp.-2°C Room Temp. < set Temp.-2°C Cooling Cooling Heating High set available set available 22°C set available set available Auto Restart Function In again after a power failure, Auto Restarting Operation procedures automatically to the previous operating conditions. case the power comes on is the function to operate Helpful information Fan speed and cooling capacity. The cooling capacity indicated in the specification is the value when the fan speed is set to high, and the capacity will be lower at low or medium fan speed. High fan speed is recommended when you wish to cool the room quickly. High Speed Owner's Manual 29 Maintenance and Service Maintenance and Service CAUTION Before performing any maintenance, turn off the main power to the system. Indoor Unit Grille, Case and Remote Control Turn the with a system off before cleanining, To clean, wipe soft, dry cloth. Do not use bleach or abrasives. NOTICE Supply power must be disconnected before Anti-biofilter cleaning Air the indoor unit. Intake Air Outlet Remote Controller Air Filters The air filters behind the front checked and cleaned once grille should be every 2 weeks 1 Remove the Air filters. Take hold of the tab and or more often if neccessary. forward to Rack remove the filter. CAUTION: When the air filter is to be removed, do not touch parts of the indoor unit. cause an injury. It may Air Filter 2 Never ? any of the followings: Water hotter than 40°C. be deformed. discoloration. ? Volatile substances. Could damage 3 the surfaces of the air conditioner. SINNER Benzene Multi-Type Air Conditioner After washing with in the shade. water, dry well Do not expose the air filter to direct sunlight or heat from a fire when drying it. SCOURING CLBARGER 4 30 Clean dirt from the air filter using a vacuum cleaner or washing with water. conspicuous, wash with a neutral detergent in lukewarm water. If hot water (50°C or more) is used, it may deformation and/or cause the metal If dirt is use Could pull slightly Install the air filter. Purifying filter (Optional) Cleaning After 1 to The PLASMA filter behind the air filters should be checked and cleaned more every 3 months once or often if necessary. removing remove the Dip 2 neutral the air filters, pull slightly forward the PLASMA filter. PLASMA filter into the water mixed with detergent, for 20~30minutes. the PLASMA filter in the shade for a day Dry 3 (Especially, the humidity must be removed perfectly on this parts). 4 Note the cuts of electric 5 Re-install the PLASMA filter to the discharge lines. original position. Don't touch this PLASMA Filter within 10 seconds after may cause an opening the inlet grille, it electric shock. Replacement ? Recomended 1 Open period use front panel : About 2 years and remove filter. air 4 Reinsert air filter and close front panel. 2 Remove air 3 Insert new purifying air filter. purifying filter. 2 1 Owner's Manual 31 Maintenance and Service Whentheairconditionerisnotgoingtobeusedforalongtime. When air conditioner is not going to be used for a long time. 1. Operate the air conditioner at the following settings for 2 to 3 hours. Type ? This operation: Fan operation mode.(Refer to will dry out the internal mechanisms. ? of page 23.) 2. Turn off the breaker. CAUTION Turn off the circuit breaker when the air conditioner is not for Helpful a long time. Dirt may collect and may cause a going to be used fire. information The air filters and your electiric bill. If the air filters become clogged with dust, the cooling capacity will drop, and 6% of the electricity used to operate the air conditioner will be wasted. When the air conditioner is to be used again. 1. Clean the air filter and install it in the indoor unit. (Refer to page 28 for cleaning it.) 2. Check that the air inlet and outlet of the indoor/outdoor unit are not blocked. 3. Check that the ground wire is connected correctly. It may be connect to the indoor unit side. Operation Tips Do not overcool the room. Keep blinds or curtains closed. This is not and for your health good wastes electricity. Keep the Do not let direct sunshine enter Adjust the the horizontal airflow direction to room when the air operation. ensure a in the sure that the doors and windows Avoid opening windows to keep as are shut much as regularly. room. in the air filter reduce the airflow and lower cooling and dehumidifying effects. Clean at least every two weeks. 32 Multi-Type Air Conditioner vertical and uniform temperature room. Ventilate the room occasionally. Blockages possible the cool air in the Clean the air filter tight. doors and temperature uniform. conditioner is in Make room once Since windows it is are kept closed, idea to open them and ventilate the room now and a then. good Maintenance and Service Troubleshooting Tips! Save time and money! Check the following points your dealer or before requesting repairs operate. ? Have you made ? Has the fuse blown been has contact a See page Explanation The air conditioner does not room persists, please service center. Case The service.... If the fault or peculiar odor. ? a mistake in timer has the circuit breaker or 16 - tripped? Check that this is not the operation? a damp walls, carpet, furniture, or smell exuded by cloth items in the - room. It seems leaking that condensation is ? Condensation occurs when the airflow from the air conditioner cools the from the air warm room air. - conditioner. Air conditioner does not operate for about 3 minutes ? This is the ? Wait about three minutes and when restarted. Does not cool protector of the mechanism. operation will - begin. or heat ? Is the air filter dirty? See air filter cleaning 30 instructions. effectively. ? The may have been very hot when the air conditioner was first turned on. Allow room room time for it to cool down. ? Has the temperature been ? Are the indoor unit's air inlet set or 18, 20 incorrectly? outlet vents - obstructed? The air conditioner operation is ? noisy. For a noise that sounds like water -This is the sound of freon flowing flowing. inside the air conditioner unit. ? For a noise that sounds like the releasing compressed air - into atmosphere. -This is the sound of the dehumidifying water being processed inside the air conditioning unit. Remote control or no display is faint, ? display at all. ? Are the batteries Are the batteries inserted in the and Crack sound is heard. Filter sign lamp (LED) is ON. ? ? depleted? (-) opposite (+) - directions? This sound is generated by the expansion/constriction of the front panel, due to changes of temperature. Cleaning the - filter, press the Timer button and button of wired remote controller at the time for 3 etc. same - sec. Owner's Manual 33 Memo 34 Multi-Type Air Conditioner
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project