LG | LRNU18GS3M0.AMTBLAT | Owner's Manual | LG LRNU18GS3M0.AMTBLAT Owner's manual

LG LRNU18GS3M0.AMTBLAT Owner's manual
ESPAÑOL
Type: ARTCOOL Mirror
Models: LRNU18GS3B0
LRNU18GS3C0
LRNU18GS3D0
LRNU18GS3M0
LRNU18GS3R0
LRNU18GS3W0
LRNU18GS3V0
LRNU24GS3B0
LRNU24GS3C0
LRNU24GS3D0
LRNU24GS3M0
LRNU24GS3R0
LRNU24GS3W0
LRNU24GS3V0
ENGLISH
LG
LRNU07GSER0
LRNU07GSEV0
LRNU07GSEB0
LRNU09GSER0
LRNU09GSEV0
LRNU09GSEB0
LRNU12GSER0
LRNU12GSEV0
LRNU12GSEB0
IMPORTANT
• Please read this owner's manual carefully and thoroughly
before installing and operating your room air conditioner.
• Please retain this owner's manual for future reference after
reading it thoroughly.
Artcool Deluxe Type Indoor Unit Owner’s Manual
TABLE OF CONTENTS
FOR YOUR RECORDS
Safety Precautions.................3
Write the model and serial numbers here:
Model #
Prior to Operation ..................8
Serial #
You can find them on a label on the side of each unit.
Product Introduction..............9
Operating Instructions.........10
Maintenance and Service ....12
Before you Call for Service .......14
Dealer's Name
Date Purchased
■ Staple your receipt to this page in the event you need
to prove date of purchase or to issue warranty.
READ THIS MANUAL
Inside you will find many helpful hints on how to use
and maintain your air conditioner properly. Just a little
preventive care on your part can save you a great deal
of time and money over the life of your air conditioner.
You'll find many answers to common problems in the
chart of troubleshooting tips. If you review our chart of
Troubleshooting Tips first, you may not need to call
for service at all.
PRECAUTION
• Contact the authorized service technician for repair or
maintenance of this unit.
• Contact the installer for installation of this unit.
• The air conditioner is not intended for use by young
children or invalids without supervision.
• Young children should be supervised to ensure that
they do not play with the air conditioner.
• When the power cord is to be replaced, replacement
work shall be performed by authorized personnel only
using only genuine replacement parts.
• Installation work must be performed in accordance with
the National Electric Code by qualified and authorized
personnel only.
2
Indoor Unit
Safety Precautions
Safety Precautions
WARNING
This symbol indicates the possibility of death or serious injury.
CAUTION
This symbol indicates the possibility of injury or damage to properties only.
■ Meanings of symbols used in this manual are as shown below.
Be sure not to do.
Be sure to follow the instruction.
■ Installation
Do not use a defective or
underrated circuit breaker.
Use this appliance on a
dedicated circuit.
WARNING
For electrical work, contact
the dealer, seller, a qualified
electrician, or an Authorized
Service Center.
• There is risk of fire or electric
shock.
• Do not disassemble or repair
the product. There is risk of fire
or electric shock.
Install the panel and the
cover of control box
securely.
Always install a dedicated
circuit and breaker.
• There is risk of fire or electric
shock.
• Improper wiring or installation
may cause fire or electric shock
Always ground the product.
• There is risk of fire or electric
shock.
Use the correctly rated
breaker or fuse.
• There is risk of fire or electric
shock.
Owner’s Manual 3
ENGLISH
To prevent injury to the user or other people and property damage, the following instructions must be
followed.
■ Incorrect operation due to ignoring instruction will cause harm or damage. The seriousness is classified
by the following indications.
Safety Precautions
Do not modify or extend the
power cable.
• There is risk of fire or electric
shock.
For installation, always contact the
dealer or an Authorized Service Center.
• There is risk of fire, electric
shock, explosion, or injury.
Do not install, remove, or
re-install the unit by
yourself (customer).
• There is risk of fire, electric
shock, explosion, or injury.
Do not install the product on
a defective installation stand.
• It may cause injury, accident, or
damage to the product.
Be cautious when
unpacking and installing
the product.
• Sharp edges could cause injury.
Be especially careful of the
case edges and the fins on the
condenser and evaporator.
Be sure the installation area
does not deteriorate with age.
• If the base collapses, the air
conditioner could fall with it,
causing property damage,
product failure, and personal
injury.
■ Operation
Do not let the air conditioner run for a
long time when the humidity is very high
and a door or a window is left open.
• Moisture may condense and
wet or damage furniture.
Do not plug or unplug the
power supply plug during
operation.
• There is risk of fire or electric
shock.
4
Indoor Unit
Take care to ensure that power
cable could not be pulled out
or damaged during operation.
Do not place anything on
the power cable.
• There is risk of fire or electric
shock.
• There is risk of fire or electric
shock.
Do not touch(operate) the
product with wet hands.
Do not place a heater or
other appliances near the
power cable.
• There is risk of fire or electrical
shock.
• There is risk of fire and electric
shock.
Safety Precautions
Do not store or use flammable
gas or combustibles near the
product.
Do not use the product in a
tightly closed space for a
long time.
• It may cause There is risk of
fire, failure of the product, or
electric shock.
• There is risk of fire or failure of
product.
• Oxygen deficiency could occur.
Gasolin
When flammable gas leaks,
turn off the gas and open a
window for ventilation
before turn the product on.
If strange sounds, or small or
smoke comes from product. Turn
the breaker off or disconnect the
power supply cable.
• Do not use the telephone or
turn switches on or off.
There is risk of explosion or fire
• There is risk of electric shock or
fire.
Do not open the inlet grill of the
product during operation.
(Do not touch the electrostatic
filter, if the unit is so equipped.)
• There is risk of physical injury,
electric shock, or product
failure.
When the product is soaked
(flooded or submerged),
contact an Authorized
Service Center.
• There is risk of fire or electric
shock.
Ventilate the product from time to time
when operating it together with a stove, etc.
• There is risk of fire or electric shock.
Stop operation and close the window
in storm or hurricane. If possible,
remove the product from the window
before the hurricane arrives.
• There is risk of property
damage, failure of product, or
electric shock.
Be cautious that water
could not enter the product.
• There is risk of fire, electric
shock, or product damage.
Turn the main power off when cleaning or
maintaining the product.
• There is risk of electric shock.
Owner’s Manual 5
ENGLISH
Do not allow water to run
into electric parts.
Safety Precautions
When the product is not be used for a long
time, disconnect the power supply plug or
turn off the breaker.
• There is risk of product damage or failure, or
unintended operation.
Take care to ensure that nobody could step
on or fall onto the outdoor unit.
• This could result in personal injury and product
damage.
CAUTION
■ Installation
Always check for gas
(refrigerant) leakage after
installation or repair of product.
• Low refrigerant levels may
cause failure of product.
Install the drain hose to ensure
that water is drained away
properly.
• A bad connection may cause
water leakage.
Keep level even when
installing the product.
• To avoid vibration or water
leakage.
90˚
Do not install the product where the
noise or hot air from the outdoor unit
could damage the neighborhoods.
• It may cause a problem for your
neighbors.
Use two or more people to lift
and transport the product.
• Avoid personal injury.
Do not install the product
where it will be exposed to
sea wind (salt spray) directly.
• It may cause corrosion on the product.
Corrosion, particularly on the condenser
and evaporator fins, could cause product
malfunction or inefficient operation.
■ Operation
Do not expose the skin directly to cool air
for long periods of time.
(Don't sit in the draft.)
• This could harm
to your health.
6
Indoor Unit
Do not use the product for special purposes, such as
preserving foods, works of art, etc. It is a consumer
air conditioner, not a precision refrigeration system.
• There is risk of
damage or
loss of property.
Safety Precautions
Do not block the inlet or
outlet of air flow.
• There is risk of fire, electric
shock, or damage to the plastic
parts of the product.
Do not touch the metal parts of
the product when removing the
air filter. They are very sharp!
• There is risk of personal injury.
x
Wa Thinner
Do not step on or put
anyting on the product.
(outdoor units)
• There is risk of personal injury
and failure of product.
Do not drink the water
drained from the product.
• It is not sanitary and could
cause serious health issues.
Always insert the filter
securely. Clean the filter
every two weeks or more
often if necessary.
• A dirty filter reduces the efficiency
of the air conditioner and could
cause product malfunction or
damage.
• There are sharp and moving
parts that could cause personal
injury.
Use a firm stool or ladder
when cleaning or
maintaining the product.
Replace the all batteries in the
remote control with new ones
of the same type. Do not mix
old and new batteries or
different types of batteries.
• Be careful and avoid personal
injury.
• There is risk of fire or explosion
Do not recharge or disassemble the
batteries. Do not dispose of batteries in a
fire.
• They may burn or explode.
Do not insert hands or other
objects through the air inlet
or outlet while the product
is operated.
If the liquid from the batteries gets onto your skin
or clothes, wash it well with clean water. Do not
use the remote if the batteries have leaked.
• The chemicals in batteries could cause burns or
other health hazards.
Owner’s Manual 7
ENGLISH
• It may cause product failure.
Use a soft cloth to clean. Do
not use harsh detergents,
solvents, etc.
Prior to operation
Prior to Operation
Preparing for operation
1. Contact an installation specialist for installation.
2. Use a dedicated circuit.
Usage
1. Being exposed to direct airflow for an extended period of time could be hazardous to your health.
Do not expose occupants, pets, or plants to direct airflow for extended periods of time.
2. Due to the possibility of oxygen deficiency, ventilate the room when used together with stoves or
other heating devices.
3. Do not use this air conditioner for non-specified special purposes (e.g. preserving precision
devices, food, pets, plants, and art objects). Such usage could damage the items.
Cleaning and maintenance
1. Do not touch the metal parts of the unit when removing the filter. Injuries can occur when handling
sharp metal edges.
2. Do not use water to clean inside the air conditioner. Exposure to water can destroy the insulation,
leading to possible electric shock.
3. When cleaning the unit, first make sure that the power and breaker are turned off. The fan rotates
at a very high speed during operation. There is a possibility of injury if the unit’s power is
accidentally triggered on while cleaning inner parts of the unit.
Service
For repair and maintenance, contact your authorized service dealer.
8
Indoor Unit
Product Introduction
Product Introduction
Here is a brief introduction of the indoor units.
Please see the information specific to your indoor unit type.
ENGLISH
Indoor Units
Art Cool Mirror(Type 1)
Display panel LED indicators
Art Cool Mirror(Type 2)
Display panel LCD indicators
Air inlet
Air filter
Air inlet
Plasma filter
Plasma filter
Air filter
Air discharge
Air discharge
Front panel
Power cord
ON/OFF button
Signal receiver
Front panel
Power cord
Signal receiver
ON/OFF button
Operation indication lamps
On/Off
: Lights up during the system operation, error code and auto restart setting.
Sleep mode
: Lights up during sleep mode auto operation.
Timer
: Lights up during timer operation or sleep mode auto operation.
Defrost mode : Lights up during defrost mode or *hot start operation (Heat pump model only)
Plasma
: The function illustrates its dynamic mode by using a multiple lighting system.
Power Display : Indicates the setting temperature and operation mode.
(Cooling, heating,auto operation,dehumidification mode)
* Hot start operation: Stops the indoor fan in heating operation for minutes to prevent cold air from blowing out
from unit.
* In defrost mode unit stops heating operation for few minutes to remove formation of ice on the heat
exchanger coils to maintain the efficiency.
Owner’s Manual 9
Operating Instructions
Operating Instructions
Name and Function of Remote Controller (Optional)
AUTO SWING
OPERATION
SET TEMP
FAN SPEED
Room Temp
AUTO Heater Preheat
JET Defrost Humidify
SLo Filter Out door
ZONE
1 2 3 4
HI
MED
LO
1
2ndF
Timer
SUB FUNCTION
Time
Operation unit No Func Program set
On Off
Set no. Time 01
03
05
07
09
11
13
15
17
19
21
23
5
14
2
3
4
6
7
Timer
Cancel
2ndF
Program
Week
Holiday
PLASMA
Set/Clr
Hour
Min
RESET
• Remote Controller Model
Standard Type : PQRCUCA0
Simple Type : PCRCUSZ0
Deluxe type
: PQRCUDS0
PQRCUDS0B
PQRCUDS0S
10
Indoor Unit
8
9
10
11
12
13
1. Operation indication screen
2. Swirl button(Not Available)
3. 2ndF button
4. Timer set/cancel
Program/Week/Holiday
Hour/Min/SET/Clr/Ventilator
5. Set temperature button
6. ON/OFF button
7. Fan operation
8. Operation mode selection button
9. Fan speed button
10. Horizontal/Vertical air flow
direction button(option)
11. Room temperature
12. Plasma button
13. Time reset button
14. Operation lamp
Operating Instructions
Wireless Remote Controller(Optional)
of handling the Remote Controller
• Aim at the signal receptor on the wired remote controller so as to operate.
• The remote control signal can be received at a distance of up to about 7m.
• Be sure that there are no obstructions between the remote controller and the signal receptor.
• Do not drop or throw the remote controller.
• Do not place the remote controller in a location exposed to direct sunlight, or near the heating unit, or any other heat source.
• Block a strong light over the signal receptor with a curtain or etc. so as to prevent the abnormal operation. (ex:electronic quick start, ELBA,
inverter type fluorescent lamp)
Owner’s Manual 11
ENGLISH
1. Start/Stop Button
Operation starts when this button is pressed.
2. Operation Mode Selection Button
Used to select the operation mode.
3. Room Temperature Setting Buttons
Used to select the room temperature.
4. Indoor Fan Speed Selector
Used to select fan speed in four steps low, medium, high
and Chaos.
5
5. Jet Cool
1
6
Speed cooling/heating operates super high fan speed.
6. Chaos Swing Button
3
Used to stop or start louver movement and set the
4
desired up/down airflow direction.
10
2
CANCEL
7. On/Off Timer Buttons
9
7
SET
ON
OFF
Used to set the time of starting and stopping operation.
AUTO CLEAN
17
11
8. Time Setting Button
8
Used to adjust the time.
13
12
9.
Timer Set/Cancel Button
14
Used to set the timer when the desired time is obtained
16
15
and to cancel the Timer operation.
10. Sleep Mode Auto Button
Used to set Sleep Mode Auto operation.
Flip-up door
11. Air Circulation Button
(opened)
Used to circulate the room air without cooling or heating.
Operation Mode
12. Room Temperature Button
Used to set the desired horizontal airflow direction.
Cooling Operation
13. Plasma(optional)
Used to start or stop the plasma-purification function.
Auto Operation
14. Horizontal Airflow Direction Control Button
(optional)
Healthy Dehumidification Operation
Used to set the desired horizontal airflow direction.
15. Reset Button
Heating Operation
Initialize remote controller.
• Cooling Model( ), Heat Pump Model( )
16. 2nd F Button
Used prior to using modes printed in blue at the bottom of buttons.
17. Auto Clean(optional)
• Remote Controller Model : PQWRHSF0(Heat pump)
Used to set Auto Clean mode.
PQWRCSF0(Cooling only)
Signal transmitter
Maintenance and Service
Maintenance and Service
Before performing any maintenance, turn off the main power to the system.
Never use any of the followings:
• Water hotter than 40°C.
Could cause deformation and/or discoloration.
• Volatile substances.
Could damage the surfaces of the air conditioner.
Pow
d er
G a s o li n e
Air Filters
The air filters behind the front panel / grill should be checked and cleaned once in
every 2 weeks or more often if necessary. To remove the filters see the self
explanatory diagrams for each model type. Clean the filters with a vacuum cleaner
or warm soapy water. If dirt is not easily removed, wash with a solution of
detergent in luke warm water. Dry well in shade after washing and reinstall the
filters back in place.
Plasma Filters
The plasma filters behind the air filter should be checked and cleaned once in every 3
months or more often if necessary. To remove the filters see the self explanatory
diagrams for each model type. Clean the filters with a vacuum cleaner. If it is dirty
wash it with water and dry well in shade an install back in place.
Deodorizer Filters
Remove the deodorizer filters behind the air filter and expose them in direct
sunlight for 2 hours.
And then insert these filters into original position.
Removal of Filters
Two different methods to open the front panel based on types of air conditioner as below ;
Type 1:
Open the upside of the panel and lift it up as shown. The hooks of the panel will come off. Remove the
air filters. Then pull out the plasma filter
Plasma filter
Front panel
Panel hook
After cleaning and drying well reinstall the filters in their original position.
Type 2:
Open the front panel as shown.
Then pull the filter tab slightly forward to remove the air filter.
After removing the air filter remove the plasma and deodorizer filter by slightly pulling forward.
Plasma filter
Front panel
Don't touch this plasma filter within 10 seconds after opening the inlet grille, it may cause an electric shock.
12
Indoor Unit
Maintenance and Service
When the air conditioner is not going to be used for a long time.
When the air conditioner is to be used again.
Operate the air conditioner at the
following settings for 2 to 3 hours.
• Type of operation: Fan operation mode.
• This will dry out the internal mechanisms.
Turn off the breaker.
Clean the air filter and install it in the
indoor unit.
(Refer to page 12 for cleaning it.)
Check that the air inlet and outlet of the
indoor/outdoor unit are not blocked.
CAUTION
Turn off the breaker when the air conditioner
is not going to be used for a long time.
Dirt may collect and may cause a fire.
Check that the ground wire is
connected correctly. It may be connect
to the indoor unit side.
Helpful information
The air filters and your electiric bill.
If the air filters become clogged with dust, the
cooling capacity will drop, and 6% of the electricity
used to operate the air conditioner will be wasted.
Operation Tips
Do not overcool the room.
Keep blinds or curtains
closed.
Keep the room temperature
uniform.
This is not good for the health
and wastes electricity.
Do not let direct sunshine
enter the room when the air
conditioner is in operation.
Adjust the vertical and
horizontal airflow direction to
ensure a uniform temperature
in the room.
Make sure that the doors
and windows are shut tight.
Clean the air filter regularly.
Ventilate the room
occasionally.
Avoid opening doors and
windows as much as possible
to keep the cool air in the
room.
Blockages in the air filter
reduce the airflow and lower
cooling and dehumidifying
effects. Clean at least once
every two weeks.
Since windows are kept
closed, it is a good idea to
open them and ventilate the
room now and then.
Owner’s Manual 13
ENGLISH
When it is not going to be used for
a long time.
Maintenance and Service
Before you call for service...
?
Troubleshooting Tips! Save time and money!
Check the following points before requesting repairs or service.... If the malfunction persist,
please contact your dealer.
The air conditioner
does not operate.
The room has a
peculiar odor.
It seems that
condensation is
leaking from the air
conditioner.
Air conditioner does
not operate for about
3 minutes when
restart.
• Check that this is not
a damp smell exuded
by the walls, carpet,
furniture or cloth
items in the room.
• Condensation occurs
when the airflow from
the air conditioner
cools the warm room
air.
• This is the protector
of the mechanism.
• Wait about three
minutes and
operation will begin.
Does not cool or heat
effectively.
The air conditioner
operation is noisy.
Crack sound is
heard.
• Is the air filter dirty?
See air filter cleaning
instructions.
• The room may have
been very hot when
the room air
conditioner was first
turned on. Allow time
for it to cool down.
• Has the temperature
been set incorrectly?
• Are the indoor unit's
air inlet or outlet vents
obstructed?
• For a noise that
sounds like water
flowing.
-This is the sound of
freon flowing inside
the air conditioner
unit.
• For a noise that
sounds like the
compressed air
releasing into
atmosphere.
-This is the sound of
the dehumidifying
water being
processed inside the
air conditioning unit.
• This sound is generated
by the expansion/
constriction of the front
panel, etc. due to
changes of
temperature.
• Have you made a
mistake in timer
operation?
• Has the fuse blown
or has the circuit
breaker been
tripped?
Remote control
display is faint, or no
display at all.
• Are the batteries
depleted?
• Are the batteries
inserted in the
opposite (+) and (-)
directions?
Filter sign lamp
(LED) is ON.
• Cleaning the filter,
press the Timer button
and button of wired
remote controller at
the same time for 3
sec.
NOTICE
WATER RESISTANT: The outdoor side of this appliance is WATER RESISTANT.
The indoor side is not water resistant and should not be exposed to
excess water.
14
Indoor Unit
Mantenimiento y servicio
Antes de llamar al servicio de reparaciones...
?
Consejos para la localización de fallos! ¡Ahorre tiempo y dinero!
Compruebe lo siguiente antes de llamar al servicio de reparaciones... Si el fallo persiste,
póngase en contacto con su distribuidor.
El aire
acondicionado no
funciona
La habitación tiene
un olor peculiar.
Parece que hay una
fuga de
condensación del
aire acondicionado.
El aire acondicionado
no funciona durante los
3 minutos siguientes a
su puesta en marcha.
• ¿Ha cometido algún
error en el uso del
temporizador?
• ¿Se ha fundido el
fusible o ha alterado
el disyuntor del
circuito?
• Compruebe que las
paredes, alfombras,
muebles o ropa de la
habitación no huelen
a humedad.
• La condensación se
produce cuando la
corriente de aire del
aire acondicionado
enfría el aire caliente
de la habitación.
• Se trata del protector
del mecanismo.
• Espere unos tres
minutos y se pondrá
en marcha.
No enfría o calienta
correctamente.
El aire
acondicionado
funciona con mucho
ruido.
Se oye un
chasquido.
El visualizador del
mando a distancia no
se ve apenas o en
absoluto.
• ¿Está el filtro sucio?
Lea las instrucciones
para la limpieza del
filtro.
• Puede que la
habitación estuviera
muy caliente cuando
encendió la primera
vez el aire
acondicionado. Deje
algún tiempo para que
se enfríe.
• ¿Ha establecido
correctamente la
temperatura?
• ¿Están obstruidos los
respiraderos de
entrada y salida de aire
de la unidad interior?
• Un ruido semejante al
agua corriendo.
-Este es el sonido del
freón que fluye dentro
de la unidad de aire
acondicionado.
• Un ruido semejante al
del aire comprimido
expulsado a la
atmósfera.
-Este es el sonido del
agua durante la
deshumidificación que
se efectúa dentro de la
unidad de aire
acondicionado.
• Este sonido se produce
por la expansión /
restricción del panel
delantero, etc., motivada
por los cambios de
temperatura.
• ¿Tiene pocas pilas?
• ¿Están las pilas
colocadas con los
polos (+) y (-) en la
dirección opuesta?
El piloto (LED) de
señal de filtro está
encendido.
• Cuando haya limpiado
el filtro, pulse al mismo
tiempo el botón del
temporizador y el del
mando a distancia
cableado durante 3
segundos.
NOTA
RESISTENTE AL AGUA: El lado exterior de este aparato es RESISTENTE AL AGUA.
El lado interior no es resistente al agua y no deberá ser expuesto a
un exceso de agua.
14
Unidad interior
ESPECIFICACIONES ELECTRICAS
220 Vca 60 Hz al ser este un manual multimodelo, para verificar el consumo refierase a la etiqueta
adherida a su producto.
LG ELECTRONICS MEXICO, S.A. DE C.V.
Sor Juana Ines de la Cruz No. 555,
San Lorenzo Tlalnepantla
Estado de Mexico
C.P. 54033
TEL. (55) 5321-1994
01800-3471919
P/No.: 3828A20872K
Printed in Korea
After reading this manual, keep it in a place easily accessible to the user for future reference.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising