LG | LZ-H200GBA2.ANWALAT | Owner's Manual | LG LZ-H050GBA2.ANWALAT Owner's manual

LG LZ-H050GBA2.ANWALAT Owner's manual
ENGLISH
ESPAÑOL
PORTUGUÊS
OWNER’S MANUAL
AIR
CONDITIONER
Please read this manual carefully before operating
your set and retain it for future reference.
VENTILATOR
www.lg.com
P/NO : MFL67455601
Copyright © 2012 - 2018 LG Electronics Inc. All Rights Reserved.
Ventilator Owner’s Manual
TABLE OF CONTENTS
Safety Precautions.........................3
FOR YOUR RECORDS
Write the model and serial numbers here:
Model #
Prior to Operation ..........................6
Serial #
You can find them on a label on the side of each unit.
Dealer's Name
Introduction ....................................7
Operating Instructions
(Accessory)...................................10
Characteristics .............................14
Maintenance and Service ............15
Date Purchased
n Staple your receipt to this page in the event you need
it to prove date of purchase or for warranty issues.
READ THIS MANUAL
Inside you will find many helpful hints on how to use
and maintain your ventilator properly. Just a little
preventive care on your part can save you a great deal
of time and money over the life of your Ventilator.
You'll find many answers to common problems in the
chart of check item prior to notify a failure. If you review
our chart of
Check item prior to notify a failure, you may not
need to call for service at all.
Check Item prior to notify
a failure .........................................20
Electronics Specifications ..........20
2 Ventilation system
PRECAUTION
• Contact the authorized service technician for
repair or maintenance of this unit.
• Contact the installer for installation of this unit.
• The ventilator is not intended for use by young
children or invalids without supervision.
• Young children should be supervised to ensure
that they do not play with the ventilator.
• When the power cord is to be replaced,
replacement work shall be performed by
authorized personnel only using only genuine
replacement parts.
• Installation work must be performed in
accordance with the National Electric Code by
qualified and authorized personnel only.
Safety Precautions
To prevent injury to the user or other people and property damage, the following instructions
must be followed.
n Incorrect operation due to ignoring instruction will cause harm or damage. The seriousness is
classified by the following indications.
This symbol indicates the possibility of death or serious injury.
This symbol indicates the possibility of injury or damage.
n Meanings of symbols used in this manual are as shown below.
Be sure not to do.
Be sure to follow the instruction.
Installation
• Do not use a defective or underrated circuit breaker. Use this appliance on a dedicated circuit.
- There is risk of fire or electric shock.
• For electrical work, contact the dealer, seller, a qualified electrician, or an Authorized Service Center.
- Do not disassemble or repair the product. There is risk of fire or electric shock.
• Always ground the product.
- There is risk of fire or electric shock.
• Install the panel and the cover of control box securely.
- There is risk of fire or electric shock.
• Always install a dedicated circuit and breaker.
- Improper wiring or installation may cause fire or electric shock
• Use the correctly rated breaker or fuse.
- There is risk of fire or electric shock.
• Do not modify or extend the power cable.
- There is risk of fire or electric shock.
• Do not install, remove, or re-install the unit by yourself (customer).
- There is risk of fire, electric shock, explosion, or injury.
• Be cautious when unpacking and installing the product.
- Sharp edges could cause injury. Be especially careful of the case edges and the fins on the condenser and
evaporator.
Owner's Manual 3
ENGLISH
Safety Precautions
Safety Precautions
Operation
• Take care to ensure that power cable could not be pulled out or damaged during operation.
- There is risk of fire or electric shock.
• Do not place anything on the power cable.
- There is risk of fire or electric shock.
• Do not touch(operate) the product with wet hands.
- There is risk of fire or electrical shock.
• Do not place a heater or other appliances near the power cable.
- There is risk of fire and electric shock.
• Do not allow water to run into electric parts.
- It may cause There is risk of fire, failure of the product, or electric shock.
• Do not store or use flammable gas or combustibles near the product.
- There is risk of fire or failure of product.
• When flammable gas leaks, turn off the gas and open a window for ventilation before turn the product on.
- Do not use the telephone or turn switches on or off.
There is risk of explosion or fire
• If strange sounds, or small or smoke comes from product. Turn the breaker off
- There is risk of electric shock or fire.
• Stop operation and close the window in storm or hurricane. If possible, remove the product from the window
before the hurricane arrives.
- There is risk of property damage, failure of product, or electric shock.
• When the product is soaked (flooded or submerged), contact an Authorized Service Center.
- There is risk of fire or electric shock.
• Be cautious that water could not enter the product.
- There is risk of fire, electric shock, or product damage.
• Turn the breaker off when cleaning or maintaining the product.
- There is risk of electric shock.
• Don’t touch a dedicated circuit or breaker with wet hands.
- There is risk of electric shock.
• Use a firm stool or ladder when cleaning or maintaining the roduct.
- Be careful and avoid personal injury.
4 Ventilation system
Safety Precautions
ENGLISH
Installation
• Use two or more people to lift and transport the product.
- Avoid personal injury.
• Do not install the product where it will be exposed to sea wind (salt spray) directly.
- It may cause corrosion on the product. Corrosion, particularly on the condenser and evaporator fins, could
cause product malfunction or inefficient operation.
Operation
• Do not expose the skin directly to cool air for long periods of time.
(Don't sit in the draft.)
- This could harm to your health.
• Do not use the product for special purposes, such as preserving foods, works of art, etc. It is a consumer
ventilator, not a precision refrigeration system.
- There is risk of damage or loss of property.
• Use a soft cloth to clean. Do not use harsh detergents, solvents, etc.
- There is risk of fire, electric shock, or damage to the plastic parts of the product.
• Do not step on or put anyting on the product. (outdoor units)
- There is risk of personal injury and failure of product.
• Use a firm stool or ladder when cleaning or maintaining the product.
- Be careful and avoid personal injury.
Owner's Manual 5
Prior to Operation
Prior to Operation
Preparing for operation
1. Contact an installation specialist for installation.
2. Use a dedicated circuit.
Usage
1. Being exposed to direct airflow for an extended period of time could be hazardous to
your health. Do not expose occupants, pets, or plants to direct airflow for extended
periods of time.
2. Due to the possibility of oxygen deficiency, ventilate the room when used together
with stoves or other heating devices.
3. Do not use this ventilator for non-specified special purposes (e.g. preserving
precision devices, food, pets, plants, and art objects). Such usage could damage the
items.
Cleaning and maintenance
1. Do not touch the metal parts of the unit when removing the filter. Injuries can occur
when handling sharp metal edges.
2. Do not use water to clean inside the ventilator. Exposure to water can destroy the
insulation, leading to possible electric shock.
3. When cleaning the unit, first make sure that the power and breaker are turned off.
The fan rotates at a very high speed during operation. There is a possibility of injury if
the unit’s power is accidentally triggered on while cleaning inner parts of the unit.
Service
For repair and maintenance, contact your authorized service dealer.
6 Ventilation system
Introduction
ENGLISH
Introduction
Symbols used in this Manual
This symbol alerts you to the risk of electric shock.
This symbol alerts you to hazards that could cause harm to the
ventilator.
NOTICE
This symbol indicates special notes.
Features
WARNING: This appliance should be installed in accordance with national wiring
regulations. This guide acts as a guide to help to explain product features.
WARNING : Indoor Unit ground wires are required for preventing electrical shock
accident during current leakage, Communication disorder by noise effect and motor
current leakage (without connection to pipe).
Model : LZ-H025GBA3
2
6
5
1
3
4
1. Blower for Supply Air
A blower for sucking outside air.
2. Control Box
3. Blower for Exhaust Air
A blower for draining polluted air outside.
4. Maintenance Cover
5. Total Heat Exchanger
Exchanges temperature and moisture
between air supply air and exhaust air.
6. Air Filter
Prevents clogging of the Total heat
exchanger due to dust.
h The figure of Total Heat Exchanger can be different by the product model.
Owner's Manual 7
Introduction
Model : LZ-H035GBA3
5
6
2
3
1
4
1. Blower for Supply Air
A blower for sucking outside air.
2. Control Box
3. Blower for Exhaust Air
A blower for draining polluted air outside.
4. Maintenance Cover
5. Total Heat Exchanger
Exchanges temperature and moisture
between air supply air and exhaust air.
6. Air Filter
Prevents clogging of the Total heat
exchanger due to dust.
h The figure of Total heat Exchanger can be different by the Product Model.
Models: LZ-H050GBA2
5
1
6
2
3
7
4
8
1. Maintenance Cover
2. Air Filter
It prevents dust from clogging in Total
Heat Exchanger.
3. Total Heat Exchanger
It changes temperature and humidity
between Supplying Air and exhausted air.
4. Blower for Exhaust Air
It is a fan for discharging the contaminated
air to outdoor.
5. Control box
6. Blower for Supply Air
It is a fan for inhaling exterior air into an
indoor space.
7. Damper plate(board)
It converts exchanging mode between total
heat ventilation and general ventilation.
8. Total Heat Exchanger holder
It is used in guiding for the installation of
Total Heat Exchanger.
h The figure of Total heat Exchanger can be different by the Product Model.
8 Ventilation system
Introduction
ENGLISH
Models: LZ-H080GBA2 / LZ-H100GBA2
5
1
6
2
3
7
4
8
1. Maintenance Cover
2. Air Filter
It prevents dust from clogging in Total Heat
Exchanger.
3. Total Heat Exchanger
It changes temperature and humidity between
Supplying Air and exhausted air.
4. Blower for Exhaust Air
It is a fan for discharging the contaminated air
to outdoor.
5. Control box
6. Blower for Supply Air
It is a fan for inhaling exterior air into an indoor
space.
7. Damper plate(board)
It converts exchanging mode between total
heat ventilation and general ventilation.
8. Total Heat Exchanger holder
It is used in guiding for the installation of Total
Heat Exchanger.
h The form of Total Heat Exchanger varies according to models.
Models: LZ-H150GBA2 / LZ-H200GBA2
5
1
2
6
3
7
4
8
1. Maintenance Cover
2. Air Filter
It prevents dust from clogging in Total Heat Exchanger.
3. Total Heat Exchanger
It changes temperature and humidity between
Supplying Air and exhausted air.
4. Blower for Exhaust Air
It is a fan for discharging the contaminated air to
outdoor.
5. Control box
6. Blower for Supply Air
It is a fan for inhaling exterior air into an indoor space.
7. Damper plate(board)
It converts exchanging mode between total heat
ventilation and general ventilation.
8. Total Heat Exchanger holder
It is used in guiding for the installation of Total Heat
Exchanger.
h The form of Total Heat Exchanger varies according to models.
Owner's Manual 9
Operating Instructions (Accessory)
Operating Instructions (Accessory)
LCD Remote Controller (PQRCVSL0 / PQRCVSL0QW)
1 OPERATION INDICATION
SCREEN
1
10
9
8
2
3
7
2
3
4
5
4
11
12
13
5
ON/OFF BUTTON
OPERATION MODE SELECTION
BUTTON
CONTROLLER RECEIVER
• Some products don't receive the
wireless signals.
14
Please attach the inform label inside of the door.
Please choose proper language depend on your
country.
FAN SPEED BUTTON
6 WIRELESS REMOTE
6
15
SET TEMPERATURE BUTTON
7
8
9
10
11
AIR FLOW BUTTON
SUBFUNCTION BUTTON
FUNCTION SETTING BUTTON
VENTILATION BUTTON
RESERVATION
12 UP, DOWN, LEFT, RIGHT
BUTTON
• To check the indoor temperature,
press
button.
13 ROOM TEMPERATURE
BUTTON
14 SETTING/CANCEL BUTTON
15 EXIT BUTTON
h Some functions may not be operated and displayed depending on the product type.
10 Ventilation system
Operating Instructions (Accessory)
It is used when air conditioner is interlinked with ventilation product.
It is a function that cools and refreshes indoor air using the ventilation product at the same time
operating the air conditioning function.
Ventilation interlinked operation
button on the remote
1 Press
controller control panel.
- It is only used when air conditioner
and general ventilation is
interlinked.
'Start/Stop' button at ventilation
2 Pressing
mode will start ventilation.
button will change the
3 Pressing
ventilation operation mode.
Pressing operation selection button
will change the mode in the order of
'Heat exchange ’ normal ’ automatic'
❈ It only displays on the remote controller
display when it is in ventilation mode, and it
displays the desired temperature when it
returns to air condition mode.
button in general
4 Pressing
ventilation mode will change airflow
speed.
Pressing airflow speed button will
change the mode in the order of 'weak ’ strong
’ extra strong'.
If CO2 sensor is installed, it can select from
'weak ’ strong ’ very strong ’ automatic'.
back to air conditioner mode
5 Changing
1)Automatic Conversion : when no button is
pressed for 15 seconds or longer, it
automatically converts back to air
conditioner mode.
2) Manual Conversion : Pressing
button
in ventilation mode will manually convert.
Owner's Manual 11
ENGLISH
Method to Operate and Select Air Volume – Interlinked Operation with Ventilation.
Operating Instructions (Accessory)
Method to Operate and Select Air Volume –Ventilation Single Operation
It is a function to cool and refresh the indoor air using general ventilation product..
Ventilation single operation
button on the remote
1 Press
controller.
button will change
2 Pressing
the ventilation mode.
Ventilation Remote Controller
Contents
mode
Display
Heat
Circulate indoor air without loss of heat
exchange
Directly circulate indoor air without going
Normal
through heat exchanger
Circulate indoor air with automatically
Automatic
comparing indoor and outdoor air
button will change
3 Pressing
the strength of the wind
- Pressing the button can select
from 'weak ’ strong ’ very strong'.
- If CO2 sensor is installed, it can select from
'weak ’ strong ’ very strong ’ automatic'.
12 Ventilation system
Operating Instructions (Accessory)
It is a function to operate ventilation function more efficiently through the ventilation additional
functions, fast / power saving settings.
Fast : ventilates fast
button in ventilation mode.
1 Press
- It converts in the order of 'fast ’
power saving' in ventilation mode.
is blinking on the display, and pressing
2 'Fast'button
will stabilize 'fast' icon, and the
function is set.
3 Pressing
settings.
button will exit the
Power Saving : efficiently ventilates and performs
power savings.
button in ventilation mode.
1 Press
- It converts in the order of 'fast ’
power saving' in ventilation mode.
Saving' is blinking on the display, and
2 'Power
pressing
button will stabilize 'Power
Saving' icon, and the function is set.
3 Pressing
settings.
button will exit the
❈ General ventilation and direct expansion
ventilation have the same additional
functions.
❈ Ventilation/Heater/Humidifier additional
function settings are the same as air
conditioner.
Owner's Manual 13
ENGLISH
Fast/Energy saving ventilation mode
Characteristics
Characteristics
Ventilation via Total Heat Exchanger
Exhausts indoor air via the Total Heat Exchanger outdoor.
• The outdoor air heat exchanged is supplied to indoor. Operate the ventilator in the
Ventilation via Total heat exchanger in summer/winter when cool/heat operation is done.
Damper
Exhaust Air
Return Air
Outdoor Air
Supply Air
Total Heat Exchanger
Normal Ventilation
Exhausts the polluted indoor-air directly without via the Total Heat
Exchanger.
• Operate the ventilator in the Normal Ventilation in spring/autumn when the Total heat exchanger
is not required.
Damper
Exhaust Air
Outdoor Air
Return Air
Supply Air
Total Heat Exchanger
CAUTION: In case of high outdoor pollution degree like yellow sand please pause the
ventilator.
14 Ventilation system
Maintenance and Service
ENGLISH
Maintenance and Service
Handling and Cleaning
To prevent function of the ventilator deteriorating, clean dust adhered to the air filter and total heat
exchanger regularly.
Cleaning Cycle
- Air filter: More than once every 6 months.
- Total heat exchanger: More than once every 2 years (Cleaning cycle may increase according to
pollution degree.)
Method to take each part out
CAUTION: Take care to ensure that you could not damage when taking the air filter out
since there is a sharp part on it.
WARNING: Turn the breaker off when cleaning the product.
CAUTION: Gloves should be worn when doing the maintenance work.
Model: LZ-H025GBA3 / LZ-H035GBA3
1. Remove the maintenance cover.
Put the hands inside of the ceiling from the maintenance cover, and pull the maintenance cover up.
(Looser the hinge and detach the maintenance cover.)
2. Take the air filter out.
Take the air filter with each contained to the
left/right downside of the Total heat exchanger.
h If it adheres to the ceiling in reverse, it is equal
to the left/right topside of the Total heat
exchanger.
Maintenance
Cover
3. Take the Total heat exchanger out.
Catch the handle and then take the Total heat
exchanger out from the main body. (2 units)
Air Filter
Main Body
Total Heat
Exchanger
Owner's Manual 15
Maintenance and Service
Model: LZ-H050GBA2 / LZ-H080GBA2 / LZ-H100GBA2
1. Remove the maintenance cover.
Put the hands inside of the ceiling from the
maintenance cover, and pull the maintenance
cover up.
(Looser the hinge and detach the maintenance
cover.)
Main Body
2. Take the air filter out.
Take the air filter with each contained to the
left/right downside of the Total heat exchanger.
h If it adheres to the ceiling in reverse, it is
equal to the left/right topside of the Total heat
exchanger.
Main Body
Air Filter
3. Take the Total heat exchanger out.
Catch the handle and then take the Total heat
exchanger out from the main body. (2 units)
Handle
16 Ventilation system
Main Body
Maintenance and Service
1. Remove the maintenance cover.
Put the hands inside of the ceiling from the maintenance cover, and pull the maintenance cover up.
(Looser the hinge and detach the maintenance cover.)
2. Take the air filter out.
Take the air filter with each contained to the
left/right downside of the Total heat exchanger.
h If it adheres to the ceiling in reverse, it is
equal to the left/right topside of the Total heat
exchanger.
Maintenance Cover
Main body
3. Take the Total heat exchanger out.
Catch the handle and then take the Total heat
exchanger out from the main body. (2 units)
Main body
Owner's Manual 17
ENGLISH
Model: LZ-H150GBA2 / LZ-H200GBA2
Maintenance and Service
Method to Clean and Replace Each Part
1. Cleaning of Air Filter
Clean once every 6 months.
Air Filter
• Clean dirt from the air filter using a vacuum cleaner or
washing with water.
(if dirt is conspicuous, wash with a neutral detergent in
lukewarm water)
Cleaner
• After washing with water, dry well in the shade.
(Do not expose the air filter to direct sunlight or heat
from a fire when drying it)
• If the air filter is damaged, purchase it from the service
center or professional agent.
2. Cleaning of Total Heat Exchanger
Suck dusts adhered to the surface of the Total heat
exchanger with a cleaner.
• Use the cleaner that attached to brush at its nozzle, and
use a soft brush.
• Do not use a hard nozzle on the cleaner.
(Otherwise, surface of the Total heat exchanger may be
damaged.)
• Never wash the Total heat exchanger with water.
• Replacement expenses are for a consideration after 2
years from the purchasing date.
• Expenses are for a consideration when you will contact
the service center even within 2 years from the
purchasing date.
• For service, always contact the dealer or an Authorized
Service Center.
Air Filter
18 Ventilation system
Total Heat Exchnger
Maintenance and Service
ENGLISH
Assembly and Check after Maintenance
1. Assembly of Total heat exchanger
Securely put the corner parts (4 parts) of the
Total heat exchanger into the
holder for assembly and slide them into the
inside of the main body.
Total Heat
Exchanger
Main Body
Assemble the
air filter into the
holder structure.
Holder for
Total Heat Exchanger
2. Assembly of air filter
Assemble the air filter into the holder structure
of the Total heat exchanger.
• Take care to ensure that surface of the Total
heat exchanger could not be damaged.
• Dusts adhered to the Total heat exchanger
may cause deterioration of Air volume.
Main Body
Air Filter
3. Assembly of maintenance cover
Fix the cover to the right hinge and fix it to the
left side. (A nameplate is adhered toward the
reading direction).
WARNING: Turn the breaker off when
cleaning the product.
Hinge
CAUTION: Gloves should be worn
when doing the maintenance work.
Main Body
Owner's Manual 19
Check Item prior to notify a failure
Check Item prior to notify a failure
Symptom
The Product doesn't work
The Product doesn't work
through you press the 'ON'
switch
Even though you change the
fan speed, the operation mode
doesn't change and it changes
to 'Auto or Low'
Check Item
Counter-measure
Is power not supplied?
Supply Power
Is Air Filter, Total heat
exchanger clogged severely?
Follow cleaning and changing
method.
Is the Indoor temperature less
than -10°c or more than 45°C?
It's standby mode for
protecting Total Heat
Exchanger.
Is the Indoor temperature less It's operation mode to protect
than -10°C or more than 45°C? Total Heat Exchanger.
Electronics Specifications
Item
Unit
LZ-H050GBA2
LZ-H080GBA2
LZ-H100GBA2
Step
SUPER-HIGH / HIGH / LOW SUPER-HIGH / HIGH / LOW SUPER-HIGH / HIGH / LOW
Current
Amps
1.92 / 1.58 / 0.79
2.77 / 2.16 / 1.44
3.41 / 2.91 / 1.76
Power Input
W
230 / 220 / 85
360 / 270 / 165
470 / 385 / 210
Item
Unit
LZ-H150GBA2
LZ-H200GBA2
Step
SUPER-HIGH / HIGH / LOW SUPER-HIGH / HIGH / LOW
Current
Amps
5.60 / 5.40 / 2.90
6.80 / 5.90 / 3.60
Power Input
W
720 / 540 / 340
930 / 770 / 420
20 Ventilation system
Models
LZ-H050GBA2
LZ-H080GBA2
LZ-H100GBA2
LZ-H150GBA2
LZ-H200GBA2
[Representative] LG Electronics Mexico, S.A de C.V
Sor Juana lnes de la Cruz No. 555 ,Col. San Lorenzo Industrial
Tlalnepantla de Baz, Estado de Mexico
C.P. 54033, Tel. 5321 1919 , Telefono sin costo 01 800 347 1919
[Manufacturer] LG Electronics Inc. Changwon 2nd factory 84, Wanam-ro,
Seongsan-gu, Changwon-si, Gyeongsangnam-do, KOREA
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising