LG FA166DAB User guide
ENGLISH
DEUTSCH
FRANÇAIS
NEDERLANDS
SLOVENŠČINA
P/NO : MFL67228259
PORTUGUÊS
FA166DAB (FA166DAB, FAS166F)
ΕΛΛΗΝΙΚΑ
Please read this manual carefully before operating
your set and retain it for future reference.
ESPAÑOL
Micro Hi-Fi System
ITALIANO
OWNER’S MANUAL
2
Getting Started
Safety Information
1
CAUTION
Getting Started
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE COVER (OR BACK) NO
USER-SERVICEABLE PARTS INSIDE REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead
symbol within an equilateral triangle
is intended to alert the user to the
presence of uninsulated dangerous
voltage within the product’s
enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an
equilateral triangle is intended
to alert the user to the presence
of important operating and
maintenance (servicing) instructions
in the literature accompanying the product.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK
HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE.
WARNING: Do not install this equipment in a
confined space such as a book case or similar unit.
CAUTION: Do not block any ventilation openings.
Install in accordance with the manufacturer’s
instructions.
Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the
product and to protect it from over heating. The
openings shall be never be blocked by placing
the product on a bed, sofa, rug or other similar
surface. This product shall not be placed in a builtin installation such as a bookcase or rack unless
proper ventilation is provided or the manufacturer’s
instruction has been adhered to.
CAUTION: This product employs a Laser System.
To ensure proper use of this product, please read
this owner’s manual carefully and retain it for future
reference. Shall the unit require maintenance,
contact an authorized service center.
Use of controls, adjustments or the performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try
to open the enclosure. Visible laser radiation when
open. DO NOT STARE INTO BEAM.
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon
a dedicated circuit;
That is, a single outlet circuit which powers only
that appliance and has no additional outlets or
branch circuits. Check the specification page of this
owner’s manual to be certain. Do not overload wall
outlets. Overloaded wall outlets, loose or damaged
wall outlets, extension cords, frayed power cords, or
damaged or cracked wire insulation are dangerous.
Any of these conditions could result in electric
shock or fire. Periodically examine the cord of your
appliance, and if its appearance indicates damage
or deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with an
exact replacement part by an authorized service
center. Protect the power cord from physical or
mechanical abuse, such as being twisted, kinked,
pinched, closed in a door, or walked upon. Pay
particular attention to plugs, wall outlets, and
the point where the cord exits the appliance. To
disconnect power from the mains, pull out the
mains cord plug. When installing the product,
ensure that the plug is easily accessible.
Getting Started
This device is equipped with a portable battery or
accumulator.
CAUTION: The apparatus shall not be exposed to
water (dripping or splashing) and no objects filled
with liquids, such as vases, shall be placed on the
apparatus.
Disposal of your old appliance
1. When this crossed-out wheeled bin
symbol is attached to a product it
means the product is covered by the
European Directive 2002/96/EC.
2. All electrical and electronic products
should be disposed of separately
from the municipal waste stream
via designated collection facilities
appointed by the government or the
local authorities.
3. The correct disposal of your old
appliance will help prevent potential
negative consequences for the
environment and human health.
4. For more detailed information about
disposal of your old appliance,
please contact your city office, waste
disposal service or the shop where
you purchased the product.
LG Electronics hereby declares that this/
these product(s) is/are in compliance
with the essential requirements and
other relevant provisions of Directive
2004/108/EC, 2006/95/EC, and
2009/125/EC.
European representative :
LG Electronics Service Europe B.V.
Veluwezoom 15, 1327 AE Almere, The
Netherlands (Tel : +31–(0)36–547–8888)
You have to set the disc format option to [Mastered]
in order to make the discs compatible with the LG
players when formatting rewritable discs. When
setting the option to Live File System, you cannot
use it on LG players.
(Mastered/ Live File System : Disc format system for
Windows Vista)
1
Getting Started
Safety way to remove the battery or the
battery from the equipment: Remove the
old battery or battery pack, follow the steps
in reverse order than the assembly. To prevent
contamination of the environment and bring on
possible threat to human and animal health, the
old battery or the battery put it in the appropriate
container at designated collection points. Do
not dispose of batteries or battery together with
other waste. It is recommended that you use
local, free reimbursement systems batteries and
accumulators. The battery shall not be exposed to
excessive heat such as sunshine, fire or the like.
3
4
Table of Contents
Table of Contents
1
Getting Started
2
6
6
6
6
6
6
7
8
10
Safety Information
Unique Features
Accesories
Playable file Requirement
– MP3/ WMA music file requirement
– Compatible USB Devices
– USB device requirement
Remote control
Front panel
Rear panel
2
Connecting
11
11
11
11
12
12
Connecting to speakers
– Attaching the speakers to the unit
Optional Equipment Connection
– PORT. IN Connection
– USB Connection
– Antenna Connection
3
Operating
13
13
13
13
13
Basic Operations
– CD/ USB Operations
Other Operations
– Programmed Playback
– Displaying file information
(ID3 TAG)
– Turn off the sound temporarily
– DEMO
Radio Operations
– Listening to the radio
– Presetting the Radio Stations
– Deleting all the saved stations
– Improving poor FM reception
– Seeing information about a Radio
station
– Listening to the DAB
– Aligning the service names
– DAB scan
– Deleting all of the saved DAB scan
stations
Sound adjustment
– Setting the surround mode
Setting the Clock
– Using your player as an alarm clock
– Sleep Timer Setting
– Dimmer
Advanced Operations
– Playing the iPod
– Compatible iPod
– Listening to music from your external
device
– Recording to USB
– To select recording bit rate and speed
13
14
14
14
14
14
14
14
15
15
15
15
15
15
16
16
17
17
17
17
18
18
19
19
Table of Contents
4
Troubleshooting
20
20
Troubleshooting
– General
5
1
5
Appendix
21
22
23
23
23
Trademarks and Licenses
Specifications
Maintenance
– Notes on Discs
– Handling the Unit
2
3
4
5
6
Getting Started
Unique Features
which creates an ISO 9660 file system.
Compatible USB Devices
1
Getting Started
USB Direct Recording
•
MP3 Player : Flash type MP3 player.
Records music to your USB device.
•
USB Flash Drive :
Devices that support USB2.0 or USB1.1.
Portable In
•
The USB function of this unit does not support
all USB devices.
Listens to music from your portable device. (MP3,
Notebook, etc)
USB device requirement
Accessories
Please check and identify the supplied accessories.
FM Antenna (1)
Battery (1)
Remote Control (1)
Stereo miniplug cable (1)
Playable file
Requirement
MP3/ WMA music file
requirement
MP3/ WMA file compatibility with this unit is limited
as follows :
•
Sampling frequency : within 32 to 48 kHz (MP3),
within 32 to 48 kHz (WMA)
•
Bit rate : within 32 to 320 kbps (MP3),
40 to 192 kbps (WMA)
•
Maximum files : Under 999
•
File extensions : “.mp3”/ “.wma”
•
CD-ROM file format : ISO9660/ JOLIET
•
We recommend that you use Easy-CD Creator,
•
Devices which require additional program
installation when you have connected it to a
computer, are not supported.
•
Do not extract the USB device while in
operation.
•
For a large capacity USB, it may take longer than
a few minute to be searched.
•
To prevent data loss, back up all data.
•
If you use a USB extension cable or USB hub, the
USB device is not recognized.
•
Using NTFS file system is not supported. (Only
FAT(16/ 32) file system is supported.)
•
This unit is not supported when the total
number of files is 1 000 or more.
•
External HDD, Card readers, Locked devices, or
hard type USB devices are not supported.
•
USB port of the unit cannot be connected to
PC. The unit cannot be used as a storage device.
Getting Started
7
Remote control
• • • • • • c • • • • • •
FOLDER · PRESET w/s: Searches
for a folder of MP3/ WMA files.
When a CD/ USB containing MP3/
WMA files in several folders is
being played, press
FOLDER · PRESET w/s selects
to the folder you want to play.
Choose a ‘preset number’ for a
radio station.
SLEEP: Sets the system to turn off
automatically at a specified time.
(Dimmer : The display window will
be darkening by half.)
B (OPEN/CLOSE): Ejects or insert
the disc from slot loader.
F (FUNCTION): Selects the fuction
and input source.
SOUND EFFECT: Chooses sound
impressions.
INFO: Checks information about
your music. MP3 files often come
with tags. The tag gives the Title,
Artist, Album or Time information.
Battery Installation
- For storing radio stations if you
have saved radio stations using
PROGRAM/MEMO. , you can
scroll through them and select
one.
- Listens to your tracks in any
order.
• • • • • • b • • • • • •
@ (MUTE): Mutes the sound.
REPEAT /MENU:
- Listens to your tracks repeatedly
or randomly.
VOL +/-: Adjusts speaker volume.
- Move to the previous
menu(iPod).
RDS/ PTY : RDS (Radio Data
System)/ Searches radio stations
by radio type.
TUNING -/+: Selects the radio
station.
Remove the battery cover on the
rear of the Remote Control, and
insert one (size AAA) battery with
4 and 5 matched correctly
PROGRAM/MEMO.:
C/V (Skip/Search):
-Skips Fast backward or Forward.
-Searches for a section within a
track.
d/M (Play/Pause): Starts or
pauses playback.
Z ENTER: Stops playback or
recording.
• • • • • • d • • • • • •
X REC: USB direct recording.
DAB INFO.:
- Search radio stations RDS (Radio
Data System) or DAB radio type.
- Changes the display information
of DAB channel.
SORT/SCAN:
- Searches radio stations by radio
type.
- Aligning the service names DAB
band scanning.
1
Getting Started
• • • • • • a • • • • • •
1 (POWER): Switches the unit
ON or OFF.
8
Getting Started
Front panel
1
Getting Started
Getting Started
a Disc Slot
b iPod dock
c 1/! (POWER)
Switches the unit ON or OFF.
e FUNC. (FUNCTION)
Changes the input source or function.
f USB Port
Connects an USB device.
g EQ
You can choose fixed sound impression.
SET/RDS, DEMO
- Confirms the setting./ RDS (Radio Data
System).
- Show DEMO.
TIMER
With the TIMER function you can turn USB, CD,
play and TUNER reception on or off at a desired
time.
CLOCK
For setting the clock and checking the time.
h B (OPEN/CLOSE)
Ejects or insert the disc from slot loader.
i C/V (Skip/Search):
Goes to next or previous file/track.
Searches backward or forward (Press and hold)
Tunes in the desired radio station.
d/M (PLAY / PAUSE)
Starts playback.
Pauses playback temporarily, press again to exit
pause mode.
j -/+ (VOLUME)
Adjusts speaker volume.
Z (STOP)
Stops playback.
k USB REC.
Recoding to USB.
l PORT. IN
Connects to a portable player with audio
outputs.
PHONES
Headphone jack
1
Getting Started
d Display window
Shows the current status of the unit.
9
10
Getting Started
Rear panel
1
Getting Started
a Antenna Connector
DAB - Connects the DAB antenna.
b ANTENNA (FM)
c Speaker terminal
d Cooling fan
e Power cord
Connecting
Connecting to
speakers
Optional Equipment
Connection
Attaching the speakers to the
unit
PORT. IN Connection
Connect an output of portable device (MP3 or PMP
etc) to the AUDIO (PORT. IN) input connector.
2
Connecting
To connect the cable to the unit, press each plastic
finger pad to open the connection terminals on the
unit. Insert the wire and release the finger pad.
Connect the black stripe of each wire to the
terminals marked - (minus) and the other end to
the terminals marked + (plus).
MP3 player, etc...
> Caution
 The speakers contain magnet parts, so color
irregularity may occur on the TV screen or
PC monitor screen. Please use the speakers
far away from either TV screen or PC
monitor.
 Make sure to install the speaker with other
people in order to prevent it from falling
and causing injuries to the installer.
11
12
Connecting
USB Connection
Antenna Connection
Connect the USB port of USB Memory (or MP3
player, etc.) to the USB port on the front of the unit.
Connect the supplied FM antenna for listening to
the radio.
Connect the FM Wire antenna to the FM antenna
connector.
2
Connecting
, Note
 Removing the USB Device from the unit
1. Choose a different function/ mode or
press Z ENTER twice in a row.
2. Remove the USB device from the unit
 You can only recharge your iPod through
USB port. To listen to music on iPod, refer to
the page 17.
, Note
 Be sure to fully extend the FM wire antenna.
After connecting the FM wire antenna, keep
it as horizontal as possible.
Operating
Basic Operations
Other Operations
CD/ USB Operations
Programmed Playback
1. Insert the disc by pressing B OPEN/CLOSE or
connect the USB device to the USB port.
The program function enables you to store your
favorite files from any disc or USB device.
2. Select the CD or USB function by pressing
F (FUNCTION) on the remote control or FUNC.
on the unit.
A program can contain 20 tracks.
3. Select a file (or track) you want to play by
pressing C/V.
Do this
Press Z ENTER
Press d/M
Press d/M
During playback, press C/V
Skipping to to go to the next track/ file or to
the next/ return to the beginning of the
previous current track/ file.
track/ file Press C twice briefly to step
back to the previous track/ file.
Searching Press and hold C/V during
for a section playback and release it at the point
within a track you want to listen to.
Searching
Press FOLDER · PRESET w/s and
for a section
then d/M.
within a folder
Press REPEAT on the remote
control repeatedly, the display
Playing
repeatedly or change in the following order,
randomly RPT1 -> RPT DIR (only MP3/ WMA)
-> RPT ALL -> RANDOM -> OFF
1. Insert a CD or USB and wait for it to be order.
2. Press PROGRAM/MEMO. on the remote control
in stop status.
3. Press C/V on the unit or on the remote
control in stop satus.
4. Press PROGRAM/MEMO. again to save and
select a next track.
5. Press d/M to play the programmed music files.
6. To clear your selection, press Z ENTER,
PROGRAM/MEMO. and then Z ENTER.
, Note
The programs are also cleared when the disc
or USB device is removed, the unit is powered
off or the function is switched to others.
Displaying file information
(ID3 TAG)
While playing an MP3 file containing file
information, you can display the information by
pressing INFO.
Turn off the sound temporarily
Press @ MUTE to mute your unit.
You can mute your unit, for example, to answer
the telephone, the “q” is displayed in the display
window.
3
Operating
To
Stop
Playback
Pause
13
14
Operating
DEMO
In the power off state, it demonstrates the function
on display window by pressing DEMO. To cancel
the DEMO, press it again.
, Note
 While DEMO, this unit will keep DEMO
status even if you unplug the power cord
connection.
 You can enjoy other functions during
the DEMO. Then the DEMO will pause to
temporary.
- Without input key in 10 sec, the DEMO
will play back automatically.
3
Operating
Radio Operations
Be sure that FM aerial is connected.
(Refer to the page 12)
Listening to the radio
1. Press F (FUNCTION) until FM appears in the
display window.
The last received station is tuned in.
2. Press and hold TUNING -/+ for about two
seconds until the frequency indication starts to
change, then release. Scanning stops when the
unit tunes in a station.
Or
Press TUNING -/+ repeatedly.
- In DAB function, press d/M to start.
3. Adjust the volume by rotating -/+ on the unit
or by pressing VOL +/- on the remote control
repeatedly.
Presetting the Radio Stations
You can preset 50 stations for FM .
Before tuning, make sure to turn down the volume.
1. Press F (FUNCTION) until FM appears in the
display window.
2. Select the desired frequency by pressing
TUNING -/+.
- In DAB function, press d/M to start.
3. Press PROGRAM/MEMO. a preset number will
flash in the display window.
4. Press FOLDER · PRESET w/s to select the
preset number you want.
5. Press PROGRAM/MEMO. The station is stored.
6. Repeat steps 2 to 5 to store other stations.
7. To listen a preset station, press
FOLDER · PRESET w/s.
Deleting all the saved stations
1. Press and hold PROGRAM/MEMO. for two
seconds. “ERASE ALL” will flash up on the unit
display.
2. Press PROGRAM/MEMO. to erase all saved
radio stations.
Improving poor FM reception
Press d/M on the unit or d/M on the remote
control. This will change the tuner from stereo to
mono and usually improve the reception.
Seeing information about a
Radio station
The FM tuner is supplied with the RDS (Radio Data
System) facility. This shows information about
the radio station being listened to. Press RDS
repeatedly to cycle through the various data types. :
PS
PTY
RT
CT
(Programme Service Name)
The name of the channel will appear in
the display
(Programme Type Recognition)
The programme type (e.g. Jazz or News)
will appear in the display.
(Radio Text)
A text message contains special
information from the broadcast station.
This text may scroll across the display.
(Time controlled by the channel)
This shows the time and date as
broadcast by the station.
You can search the radio stations by programme
type by pressing RDS. The display will show the last
PTY in use. Press PTY one or more times to select
your preferred programme type. Press and hold
C/V. The tuner will search automatically.
When a station is found the search will stop.
Operating
Listening to the DAB
You can change the display information of the
currently broadcasting DABchannel. Press
DAB INFO. on the remote control repeatedly, the
display changes in the following order,
SERVICE -> PTY NAME -> FREQ -> DLS -> QUALITY
-> ENSEMBLE
Select a display mode and then press C/V,
the initials of the servicename are displayed.
SERVICE
Displays the Name of the channel for
the current broadcast.
PTY NAME
Displays the Type of the channel for
the current broadcast.
Displays the frequency of the channel
for the current broadcast.
DLS
It displays the current Scroll of the
channel which is selected.
QUALITY
It displays the current strength of the
broadcast signal in Bar form.
ENSEMBLE
Displays the Ensemble of the channel
for the current broadcast.
Aligning the service names
Press SORT/SCAN on the remote control to display
the sorting mode of DAB broadcastings. Then, press
the button once again to change the mode.
Default sort: The service names are aligned in a
scanning order.
Name sort: The service names are aligned in an
alphabetical order.
DAB scan
Press SORT/SCAN on the remote control for longer
than 3 seconds, all ofthe DAB bands are scanned.
Then press it again, scanning will be cancelled.
Deleting all of the saved DAB
scan stations
Press and hold DAB INFO. on the remote control
for 3 seconds. “DAB INIT” will be displayed. Press
DAB INFO. to erase all the saved stations.
Sound adjustment
Setting the surround mode
This system has a number of pre-set surround
sound fields. You can select a desired sound mode
by using SOUND EFFECT on the remote control or
EQ on the unit.
The displayed items for the Equalizer may be
different depending on sound sources and effects.
On Display
Description
NATURAL
You can enjoy comfortable and
natural sound.
Local
Specialization
equalizer
Regionally optimized sound
effect. (FORRO/ FUNK/
SERTANEJO/ DANGDUT/
ARABIC/ PERSIAN/ INDIA/
REGUETON/ MERENGUE/ SALSA/
SAMBA/ CUMBIA/ AFRO)
AUTO EQ
Realizes the sound equalizer that
is the most similar to the genre
of which is included in the MP3
ID3 tag of song files.
POP
CLASSIC
JAZZ
ROCK
This program lends an
enthusiastic atmosphere to the
sound, giving you the feeling
you are at an actual rock pop,
jazz or classic concert.
MP3 -- OPT
This function is optimized
for compressible MP3 file. It
improves the treble sound.
BASS BLAST
Reinforces the treble, bass and
surround sound effect.
LOUDNESS
Improves the bass and treble
sound.
VIRTUAL
You can enjoy more virtual
surround sound.
BYPASS
You can enjoy the sound
without equalizer effect.
3
Operating
FREQ
15
16
Operating
, Note
 On some speakers, sound may not be heard
or heard in low sound depending on the
sound mode.
 Maybe you need reset the surround mode,
after switching the input, sometimes even
after the sound track changed.
Setting the Clock
1. Turn the unit on.
2. Press CLOCK for at least 2 seconds.
3
3. Choose time mode by pressing C/V.
Operating
- AM 12:00 (for an AM and PM display) or 0:00
(for a 24 hour display)
4. Press SET to confirm your selection.
5. Select the hours by pressing C/V.
6. Press SET.
7. Select the minutes by pressing C/V.
8. Press SET.
Using your player as an alarm
clock
1. Turn the unit on.
2. Press TIMER. Each functions flashes.
3. Press SET when the function you want to be
woken by is showing.
4. “ON TIME” will be displayed. This is your desired
time to unit turns on. Press C/V to
change the hours and minutes and press SET to
save.
5. The “OFF TIME” will be displayed. This is your
desired time to unit turns off.
6. Press C/V to change the hours and
minutes and press SET to save.
7. Press C/V to change the volume and
press SET to save. The clock icon "(“ shows
that the alarm is set.
8. Press TIMER button 2 times. You can check the
setting status.
, Note
 If you set the clock time, you can check the
time by pressing CLOCK even when the
player is turned off.
 If you set the clock time and alarm, you
can check the alarm icon “(“ by pressing
CLOCK even when the player is turned off.
 If you set the clock time and alarm, you
can check the alarm icon “(“ and setting
informaiton by pressing TIMER even when
the unit is turned off. Then this function will
working in everyday.
Operating
Sleep Timer Setting
Press SLEEP repeatedly to select delay time
between 10 and 180 minutes. After the delay time,
unit will turn off.
To cancel the sleep function, press SLEEP
repeatedly until “SLEEP 10” appears, and then press
SLEEP once again while “SLEEP 10” is displayed.
, Note
17
Advanced Operations
Playing the iPod
You can enjoy the sound with your iPod. For details
about iPod, refer to the iPod User Guide.
1. Connect the iPod firmly.
 You can check the remaining time before
the unit turns off.
 Press SLEEP. The remaining time appears in
the display window.
 Sleep function will working after dimmer.
3
Operating
Dimmer
Press SLEEP once. The display window will be
darkening by half. To cancel it, press SLEEP
repeatedly until dim off. If touch the buttons in
Sleep Timer mode, the buttons will be lightening
for 5 seconds and darkening again.
If you turn this unit on, your iPod is
automatically turned on and recharging starts.
2. Press FUNC. on the unit or F (FUNCTION) on
the remote control to select iPod function. You
can operate your iPod through an iPod’s display
by using the supplied remote control and also
control on your iPod.
18
Operating
To
, Note
Do this
ON UNIT
ON REMOTE
Pauses or
restart
d/M
d/M
Skip
C/V
C/V
Search
Press and hold
C/V
Press and hold
C/V
Move to the
previous
menu
-
REPEAT
/MENU
-
FOLDER
PRESET
W/S
I
Z ENTER
3
Operating
Move to the
desired item
Chooses a
item
Compatible iPod
 We recommend installing the latest software
version.
 The unit supports the models as follows:
iPod nano 1 G, 2 G, 3 G, 4 G, 5 G, 6 G/
iPod classic/ iPod 4 G, 5 G/
iPod touch 2 G, 3 G, 4 G/ iPhone 3 G, 4.
For some models, the unit may not operate
depending on the firmware version.
 Depending on your iPod’s software version, you
may not control your iPod from the player.
 If this unit displays an error message, follow
the message. An error message “ERROR”.
- Your iPod is not connected firmly.
- This unit recognizes your iPod as an
unknown device.
- Your iPod is exceptionally low in power.
/ The battery needs to be charged.
/ If you charge the battery while iPod
is extremely low in power, it may take
longer to be charged.
 iPod does not support recording function
when connected.
 Depending on your iPod’s software version,
it may not be possible to control your iPod
from this unit. We recommed installing the
latest software version.
 If you use an application, make a call, or
send and receive SMS text message, etc. on
iPod touch or iPhone, disconnect it from
iPod dock of this unit and then use it.
 If you have a problem with your iPod, please
visit www.apple.com/support/ipod.
Listening to music from your
external device
The unit can be used to play the music from many
types of external device.
(Refer to the page 11)
1. Connect the external device to the PORT. IN
connector of the unit.
2. Turn the power on by pressing 1/! (Power).
3. Select the PORTABLE function by pressing
FUNC. on the unit or F (FUNCTION) on the
remote control.
4. Turn the external device and start it playing.
Operating
Recording to USB
1. Connect the USB device to the unit.
2. Select a function by pressing FUNC. on the unit
or F (FUNCTION) on the remote control.
, Note
 You can check the recording percentage
rate for the USB record on the display
window during the recording. (MP3/ WMA
CD Only)
One track recording - You can record to USB
after playing a file you want.
 During recording MP3/ WMA, there is no
sound.
All tracks recording - You can recording to USB
after stop.
 When you stop recording during playback,
the file that has been recorded at that time
will be stored. (AUDIO CD Only)
Program list recording - After showing the
programmed list, you can record it to USB.
 Do not remove the USB device or turn
off the unit during USB recording. If not,
an incomplete file may be made and not
deleted on PC.
3. Start the recording by pressing USB REC. on the
unit or X REC on the remote control.
19
 If USB recording does not work, the
message like “NO USB”, “ERROR”, “FULL” or “NO
REC” is displayed on the display window.
Pausing recording
 Multi card reader device or External HDD
can not be used for USB recording.
During recording, press USB REC. on the unit or
X REC on the remote control to pause recording.
Press it again to restart recording. (Only Radio/
Portable)
To select recording bit rate
and speed
1. Press USB REC. on the unit or X REC on the
remote control for longer than 3 seconds.
 A file is recorded by about 512 Mbyte when
you record for a long term.
 When you stop recording during playback,
the file will not be stored.
 You may not store more than 999 files.
 It’ll be stored as follows.
AUDIO CD
MP3/ WMA
The other
source*
2. Use C/V on the unit or remote control to
select the bit rate.
3. Press USB REC. on the unit or X REC on the
remote control again to select the recording
speed.
4. Press C/V on the unit or on the remote
control to select a desired recording speed;
(Only AUDIO CD)
X1 SPEED
- You can listen to music while recording it.
X2 SPEED
- You can just record the music file.
5. Press USB REC. on the unit or X REC on the
remote control to finish the setting.
* : TUNER, Portable and the like.
The making of unauthorized copies of copyprotected material, including computer
programs, files, broadcasts and sound
recordings, may be an infringement of
copyrights and constitute a criminal offense.
This equipment should not be used for such
purposes.
Be responsible
Respect copyrights
3
Operating
4. To stop recording, press Z on the unit or
Z ENTER on the remote control.
20 Troubleshooting
Troubleshooting
General
Problem
Cause & Correction
 The power cord is not plugged in. Plug in the power cord.
No Power.
 Check whether electricity failed. Check the condition by operating other
electronic devices.
 Check whether you select right function. Press F (FUNCTION) and check the
selected function.
No sound.
 If not, connect speaker cables correctly. Speaker cables connected
correctly.
 An unplayable disc is inserted. Insert a playable disc.
4
The unit does not start
playback.
 No disc is inserted. Insert a disc.
 The disc is dirty. Clean the disc. (Refer to the 23 page)
Troubleshooting
 The antenna is positioned or connected poorly. Connect the antenna
securely.
Radio stations cannot
be tuned in properly.
 The signal strength of the radio station is too weak. Tune to the station
manually.
 No stations have been preset or preset stations have been cleared (when
tuning by scanning preset channels). Preset some radio stations, see page
14 for details.
 The remote control is too far from the unit. Operate the remote control
within about 23 ft (7 m).
 There is an obstacle in the path of the remote control and the unit. Remove
The remote control
the obstacle.
does not work properly.
 The batteries in the remote control are exhausted. Replace the batteries
with new ones.
iPod does not work.
 Check whether the player is connected to the unit correctly. Connect it to
the unit correctly.
Appendix
21
Trademarks and
Licenses
iPod is a trademark of Apple Inc., registered in
the U.S. and other countries.
iPhone is a trademark of Apple Inc. “Made
for iPod” and “Made for iPhone” mean that
an electronic accessory has been designed
to connect specifically to iPod or iPhone
respectively, and has been certified by the
developer to meet Apple performance standards.
Apple is not responsible for the operation of
this device or its compliance with safety and
regulatory standards.
Please note that the use of this accessory with
iPod, iPhone may affect wireless performance.
5
Appendix
22 Appendix
Specifications
General
Power requirements
200 - 240 V , 50/ 60 Hz
Power consumption
45 W
Dimensions (W x H x D)
135 X 295 X 315 mm
Net Weight (Approx.)
3.45 kg
Operating temperature
5 °C to 35 °C (41 °F to 95 °F)
Operating humidity
5 % to 90 %
Bus Power Supply
USB DC 5 V 0 500 mA
iPod DC 5 V 0 1 A
Inputs/ Outputs
PORT. IN
0.5Vrms (3.5 mm stereo jack)
Tuner
FM Tuning Range
87.5 to 108.0 MHz or 87.50 to 108.00 MHz
Amplifier
5
Stereo mode
80 W + 80 W (4Ω at 1kHz)
Appendix
CD
Frequency Response
40 to 20 000 Hz
Signal-to-noise ratio
75 dB
Dynamic range
80 dB
Front Speaker
Type
3 Way 4 speaker
Impedance Rated
4Ω
Input Power
80 W
Max. Input Power
160 W
Net Dimensions (W x H x D)
126 X 295 X 315 mm
Net Weight
3.62 kg
 Design and specifications are subject to change without notice.
Appendix 23
Maintenance
Handling the Unit
When shipping the unit
Notes on Discs
Handling Discs
Please save the original shipping carton and
packing materials. If you need to ship the unit, for
maximum protection, re-pack the unit as it was
originally packed at the factory.
Never stick paper or tape on the disc.
Storing Discs
After playing, store the disc in its case. Do not
expose the disc to direct sunlight or sources of heat
and never leave it in a parked car exposed to direct
sunlight.
Cleaning Discs
Do not use strong solvents such as alcohol,
benzine, thinner, commercially available cleaners,
or anti-static spray intended for older vinyl records.
Keeping the exterior surfaces clean
Do not use volatile liquids such as insecticide spray
near the unit.
Wiping with strong pressure may damage the
surface.
Do not leave rubber or plastic products in contact
with the unit for a long period of time.
Cleaning the unit
To clean the player, use a soft, dry cloth. If the
surfaces are extremely dirty, use a soft cloth lightly
moistened with a mild detergent solution. Do not
use strong solvents such as alcohol, benzine, or
thinner, as these might damage the surface of the
unit.
Maintaining the Unit
Appendix
The unit is a high-tech, precision device. If the
optical pick-up lens and disc drive parts are dirty
or worn, the picture quality could be diminished.
For details, please contact your nearest authorized
service center.
5
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising