LG | XV-N380BUX | Owner's Manual | LG XV-N382SUX Owner's Manual

LG XV-N382SUX Owner's Manual
DV300-JP.BAREJJB_MFL62178436_ENG
DVD PLAYER
XV-N380B
XV-N382S
INSTRUCTIONS
LVT2010-022A
[UX]
CAUTION: TO REDUCE THE RISK
OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
WARNING: TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPARATUS TO RAIN OR MOISTURE .
WARNING: Do not install this equipment in a confined space
such as a bookcase or similar unit.
CAUTION: Do not block any ventilation openings. Install in
accordance with the manufacturer's instructions.
•
•
•
The STANDBY/ON button does not completely shut off
mains power from the unit, but switches operating
current on and off.
When moving the product, press STANDBY/ON to turn
off the power, and wait at least 30 seconds before
unplugging the power cord. Then, wait at least 2 minutes
before moving the product.
When discarding batteries, environmental problems must
be considered and the local rules or laws governing the
disposal of these batteries must be followed strictly.
CAUTION
• Do not block the ventilation openings or holes.
(If the ventilation openings or holes are blocked by a
newspaper or cloth, etc., the heat may not be able to
get out.)
Slots and openings in the cabinet are provided for ventilation
and to ensure reliable operation of the product and to protect
it from over heating.
The openings should be never be blocked by placing the
product on a bed, sofa, rug or other similar surface. This
product should not be placed in a built-in installation such as
a bookcase or rack unless proper ventilation is provided or
the manufacturer's instruction have been adhered to.
• Do not place any naked flame sources, such as lighted
candles, on the apparatus.
CAUTION:
CLASS 1 LASER PRODUCT
This product employs a Laser System.
To ensure proper use of this product, please read this
owner’s manual carefully and retain it for future reference.
Should the unit require maintenance, contact an authorized
service center.
Use of controls, adjustments or the performance of
procedures other than those specified herein may result in
hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try to open
the enclosure. Visible laser and/or invisible radiation when
open. DO NOT STARE INTO BEAM.
• Battery shall not be exposed to excessive heat such as
sunshine, fire or the like.
CAUTION concerning the Power Cord
Most devices are recommended be placed on a
dedicated circuit;
That is, a single outlet circuit which powers only that
electronic device and has no additional outlets or branch
circuits. Check the specification page of this owner's manual
to be certain.
Do not overload wall outlets. Overloaded wall outlets, loose
or damaged wall outlets, extension cords, frayed power
cords, or damaged or cracked wire insulation are dangerous.
Any of these conditions could result in electric shock or fire.
Periodically examine the cord of your appliance, and if its
appearance indicates damage or deterioration, unplug it,
discontinue use of the appliance, and have the cord replaced
with an exact replacement part by an authorized servicer.
Protect the power cord from physical or mechanical abuse,
such as being twisted, kinked, pinched, closed in a door, or
walked upon. Pay particular attention to plugs, wall outlets,
and the point where the cord exits the appliance.
To disconnect power from the mains, pull out the mains cord
plug. When installing the product, ensure that the plug is
easily accessible.
2
CAUTION:
• When discarding batteries, environmental problems
must be considered and local rules or laws governing
the disposal of these batteries must be followed strictly.
• Do not expose this apparatus to rain, moisture,
dripping or splashing and that no objects filled with
liquids, such as vases, shall be placed on the
apparatus.
Contents
Introduction . . . . . . . . . . . . . . . . . .4-7
Operation . . . . . . . . . . . . . . . . .13-18
Symbol Display . . . . . . . . . . . . .4
General Features . . . . . . . . . . . . . . . . . . . . . .13
Symbol Used in this Manual . . . . . . . . . . . . . .4
Additional Features . . . . . . . . . . . . . . . . . . . .14
Notes on Discs . . . . . . . . . . . . . . . . . . . . . . . .4
Playing an Audio CD or MP3/WMA file . . . . .15
Handling Discs . . . . . . . . . . . . . . . . . . . . . . .4
Programmed Playback . . . . . . . . . . . . . . . . .16
Storing Discs . . . . . . . . . . . . . . . . . . . . . . . .4
Repeat Programmed Tracks . . . . . . . . . . . .16
Cleaning Discs . . . . . . . . . . . . . . . . . . . . . . .4
Erasing a Track from Program List . . . . . . .16
About the
Types of Playable Discs . . . . . . . . . . . . . . . . .5
Erasing the Complete Program List . . . . . .16
Regional Code . . . . . . . . . . . . . . . . . . . . . . . . .5
Viewing a JPEG file . . . . . . . . . . . . . . . . . . . .17
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Slide Show . . . . . . . . . . . . . . . . . . . . . . . . .17
Remote Control . . . . . . . . . . . . . . . . . . . . . . . .7
Still Picture . . . . . . . . . . . . . . . . . . . . . . . . .17
Remote Control operation . . . . . . . . . . . . . .7
Moving to another file . . . . . . . . . . . . . . . . .17
Remote Control Battery installation . . . . . . . .7
Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Rotating the picture . . . . . . . . . . . . . . . . . .17
Installation and Setup . . . . . . . . .8-12
Listening to MP3 music while watching
picture . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Playing a DVD VR format Disc . . . . . . . . . . .18
Setting up the Player . . . . . . . . . . . . . . . . . . . .8
DVD Player Connections . . . . . . . . . . . . . . . . .8
Reference . . . . . . . . . . . . . . . . . .19-22
Video and Audio Connections to Your TV . . .8
Audio Connection to Optional Equipment . . .9
When you turn on for the first time . . . . . . . .10
Displaying Disc Information on-screen . . . .10
Initial Settings . . . . . . . . . . . . . . . . . . . . . .10-12
General Operation . . . . . . . . . . . . . . . . . . .10
LANGUAGE . . . . . . . . . . . . . . . . . . . . . . . .11
Remote Control Function . . . . . . . . . . . . . . . . . . .19
Maintenance and Service . . . . . . . . . . . . . . . .19
Language Codes . . . . . . . . . . . . . . . . . . . . . . .20
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . .21
Specifications . . . . . . . . . . . . . . . . . . . . . . . . .22
• Menu Language . . . . . . . . . . . . . . . . . .11
• Disc Audio / Subtitle / Menu . . . . . . . . .11
DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . .11
• TV Aspect . . . . . . . . . . . . . . . . . . . . . .11
• Display Mode . . . . . . . . . . . . . . . . . . . .11
• Progressive Scan . . . . . . . . . . . . . . . . .11
• TV Output Select . . . . . . . . . . . . . . . . .11
AUDIO . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
• Dolby Digital / DTS / MPEG . . . . . . . . .12
• Sample Freq. (Frequency)
. . . . . . . . .12
• DRC (Dynamic Range Control) . . . . . .12
• Vocal . . . . . . . . . . . . . . . . . . . . . . . . . .12
OTHERS . . . . . . . . . . . . . . . . . . . . . . . . . .12
• PBC . . . . . . . . . . . . . . . . . . . . . . . . . .12
• B.L.E. (Black Level Expansion) . . . . . .12
3
Introduction
To ensure proper use of this product, please read this
owner’s manual carefully and retain it for future
reference.
Notes on Discs
Handling Discs
This manual provides information on the operation
and maintenance of your DVD player. Should the unit
require service, contact an authorized service location.
About the
Symbol Display
“
” may appear on your TV display during
operation and indicates that the function explained in
this owner’s manual is not available on that specific
DVD video disc.
Storing Discs
Symbol Used in this Manual
After playing, store the disc in its case. Do not expose
the disc to direct sunlight or sources of heat and never
leave it in a parked car exposed to direct sunlight.
Note:
Indicates special notes and operating features.
Cleaning Discs
Tip:
Indicates tips and hints for making the task easier.
A section whose title has one of the following symbols is
applicable only to the disc represented by the symbol.
4
Do not touch the playback side of the disc. Hold the
disc by the edges so that fingerprints do not get on
the surface. Never stick paper or tape on the disc.
ALL
All discs and file listed below
DVD
DVD and finalized DVD±R/RW
VCD
Video CDs
ACD
Audio CDs
MP3
MP3 files
WMA
WMA files
Fingerprints and dust on the disc can cause poor
picture quality and sound distortion. Before playing,
clean the disc with a clean cloth. Wipe the disc from
the center out.
Do not use strong solvents such as alcohol, benzine,
thinner, commercially available cleaners, or anti-static
spray intended for older vinyl records.
In addition, this unit plays DVD±R/RW and CD-R/RW,
Dual disc that contains audio titles, MP3, WMA, and/or
JPEG files.
This indicates a product feature that is
capable of playing DVD-RW discs
recorded with Video Recording format.
Notes:
• Depending on the conditions of the recording
equipment or the CD-R/RW (or DVD±R/RW) disc
itself, some CD-R/RW (or DVD±R/RW) discs
may not be played on the unit.
• Do not use irregularly shaped CDs (e.g., heartshaped or octagonal) since they may result in
malfunctions.
• This DVD player requires discs and recordings to
meet certain technical standards in order to achieve
optimal playback quality. Pre-recorded DVDs are
automatically set to these standards. There are
many different types of recordable disc formats
(including CD-R containing MP3 or WMA files) and
these require certain pre-existing conditions (see
above) to ensure compatible playback.
Customers should note that permission is
required in order to download MP3 / WMA files
and music from the Internet. Our company has
no right to grant such permission. Permission
should always be sought from the copyright
owner.
Introduction
Audio CD
(8 cm / 12 cm disc)
Notes on Regional Codes
• Most DVD discs have a globe with one or more
numbers in it clearly visible on the cover. This
number must match your unit’s regional code or the
disc cannot play.
• If you try to play a DVD with a different regional
code from your player, the message “Check
Regional Code” appears on the TV screen.
Installation and Setup
Video CD (VCD/SVCD)
(8 cm / 12 cm disc)
This unit has a regional code printed on the rear of the
unit. This unit can play only DVD discs labeled as the
same as the rear of the unit or “ALL”.
Notes on Copyrights:
It is forbidden by law to copy, broadcast, show,
broadcast via cable, play in public, or rent copyrighted
material without permission. This product features the
copy protection function developed by Macrovision.
Copy protection signals are recorded on some discs.
When recording and playing the pictures of these
discs picture noise will appear. This product
incorporates copyright protection technology that is
protected by method claims of certain U.S. patents
and other intellectual property rights owned by
Macrovision Corporation and other rights owners.
The Use of this copyright protection technology must
be authorized by Macrovision Corporation, and is
intended for home and other limited viewing uses only
unless otherwise authorized by Macrovision
Corporation. Reverse engineering or disassembly is
prohibited.
Operation
DVD
(8 cm / 12 cm disc)
Regional Code
CONSUMERS SHOULD NOTE THAT NOT ALL HIGH
DEFINITION TELEVISION SETS ARE FULLY
COMPATIBLE WITH THIS PRODUCT AND MAY
CAUSE ARTIFACTS TO BE DISPLAYED IN THE
PICTURE. IN CASE OF 525 OR 625 PROGRESSIVE
SCAN PICTURE PROBLEMS, IT IS
RECOMMENDED THAT THE USER SWITCH THE
CONNECTION TO THE ‘STANDARD DEFINITION’
OUTPUT. IF THERE ARE QUESTIONS REGARDING
OUR TV SET COMPATIBILITY WITH THIS MODEL
525p AND 625p DVD PLAYER, PLEASE CONTACT
OUR CUSTOMER SERVICE CENTER.
Reference
Types of Playable Discs
5
Front Panel
a
b
d
e
f
g
h
i
a 1/' STANDBY/ON
Switches the unit ON and OFF.
f N (PLAY)
Starts playback.
b Disc Tray
Insert a disc here.
g x (STOP)
Stops playback.
c Z (OPEN/CLOSE)
Opens or closes the disc tray.
h . (SKIP)
Returns to the beginning of current chapter or
track or go to the previous chapter or track.
Press and hold the button for search backward.
d Display window
Shows the current status of the unit.
e Remote Sensor
Point the remote control here.
6
c
i > (SKIP)
Go to the next chapter or track.
Press and hold the button for search forward.
Remote Control
OPEN/CLOSE (Z)
Opens and closes the disc tray.
DISPLAY
Accesses On-Screen Display.
DVD MENU
Accesses menu on a DVD disc.
Introduction
1/')
STANDBY/ON (1
Switches DVD Player ON and OFF.
b / B / v / V (left/right/up/down)
Selects an item in the menu.
SKIP (. / >)
Go to next chapter or track.
Returns to the beginning of current
chapter or track or go to the
previous chapter or track.
ENTER (
)
Confirms menu selection.
SETUP
Accesses or removes Setup menu.
RETURN (O)
Displays the menu of a video CD
with PBC.
Installation and Setup
PAUSE/STEP ( X )
Pauses playback temporarily/ press
repeatedly for frame-by-frame
playback.
STOP (x)
Stops playback.
PLAY (N)
Starts playback.
0-9 numerical buttons
Selects numbered items in a menu.
PROGRAM
Enter to program edit mode.
CLEAR
Removes a track number on the
Program List or a mark on the
Marker Search menu.
AUDIO (
)
Selects an audio language or an
audio channel.
SUBTITLE (
)
Selects a subtitle language.
ANGLE (
)
Selects a DVD camera angle,
if available.
ZOOM
Enlarges video image.
Operation
SCAN (m / M)
Search backward or forward.
MARKER
Marks any point during playback.
SEARCH
Displays MARKER SEARCH menu.
TITLE
Displays title menu, if available.
REPEAT
Repeats chapter, track, title or all.
Cautions:
• Do not mix old and new
batteries and never mix
different types of batteries
such as standard, alkaline,
etc.
• Do not put the batteries in
the place where young
children can reach.
Remote Control Battery
installation
Detach the battery
cover on the rear
of the remote
control, and insert
two batteries (size
AAA) with 3 and
# aligned
correctly.
RANDOM
Plays tracks in random order.
A-B
Repeats sequence from point A to
point B.
Reference
Remote Control operation
Point the remote control at
the remote sensor and press
the buttons.
7
Installation and Setup
Setting up the Player
The picture and sound of a nearby TV, VCR, or radio
may be distorted during playback. If this occurs,
position the player away from the TV, VCR, or radio,
or turn off the unit after removing the disc.
DVD Player Connections
Depending on your TV and other equipment there are
various ways you can connect the player. Please refer
to the manuals of your TV, stereo system or other
devices as necessary for additional connection
information.
Rear of TV
Video and Audio Connections
to Your TV
Make one of the following connections, depending on
the capabilities of your TV.
Cautions:
• Do not connect the S-VIDEO OUTPUT and
COMPONENT VIDEO OUTPUT jacks together to
your TV, otherwise the color of video image will not
be displayed properly.
• Make sure the DVD player is connected directly to
the TV and not to a VCR, otherwise the DVD image
could be distorted by the copy protection system.
S-Video – Connect the S-VIDEO OUTPUT jack on
the DVD Player to the S-Video in jack on the TV
using the S-Video cable (S).
Caution: You must set the [TV Output Select]
option to [S-Video] on the setup menu to use
this connection. (See page 11)
Video – Connect the VIDEO OUTPUT jack on the
DVD player to the video in jack on the TV using
the video cable (V).
Audio – Connect the left and right AUDIO
OUTPUT jacks of the DVD Player to the audio left
and right IN jacks on the TV using the audio
cables (A).
Do not connect the DVD Player’s AUDIO OUTPUT
jack to the phone in jack (record deck) of your
audio system.
Rear of DVD Player
Component Video – Connect the COMPONENT /
PROGRESSIVE SCAN OUTPUT jacks on the DVD
Player to the corresponding jacks on the TV using
an Y PB PR cable (C).
Caution: You must set the [TV Output Select]
option to [YPbPr] on the setup menu to use this
connection. (See page 11)
Progressive Scan
• If your television is a high-definition or “digital
ready” television, you may take advantage of
the DVD player’s progressive scan output for
the highest possible video resolution.
• Set the Progressive Scan to “On” on the setup
menu for progressive scan signal. (Refer to
page 11)
• Progressive scan does not work with the
analog video connections (yellow VIDEO
OUTPUT jack and S-VIDEO OUTPUT jack).
8
Rear of DVD Player
Introduction
Connect the DVD player to your optional equipment
for audio output.
Amplifier equipped with 2-channel analog stereo
or Dolby Pro Logic ll / Pro Logic: Connect the left
and right AUDIO OUTPUT jacks on the DVD player to
the audio left and right IN jacks on your amplifier,
receiver, or stereo system, using the audio cables (A).
Amplifier equipped with 2-channel digital stereo
(PCM) or audio / video receiver equipped with a
multi-channel decoder (Dolby Digital™, MPEG 2,
or DTS): Connect one of the DVD Player’s DIGITAL
AUDIO OUTPUT jacks (COAXIAL X) to the
corresponding jack on your amplifier. Use an optional
digital (COAXIAL X) audio cable.
Installation and Setup
Audio Connection to Optional
Equipment
Digital Multi-channel sound
A digital multi-channel connection provides the best
sound quality. For this you need a multi-channel audio
/ video receiver that supports one or more of the
audio formats supported by your DVD player such as
MPEG 2, Dolby Digital and DTS. Check the receiver
manual and the logos on the front of the receiver.
Notes:
• If the audio format of the digital output does not
Manufactured under license from Dolby
Laboratories. “Dolby” and the double-D
symbol are trademarks of Dolby Laboratories.
• Six Channel Digital Surround Sound via a digital
connection can only be obtained if your receiver is
equipped with a Digital Multi-channel decoder.
Operation
Amplifier (Receiver)
match the capabilities of your receiver, the receiver
produces a strong, distorted sound or no sound at
all.
Reference
Manufactured under license under U.S. Patent
#: 5,451,942 & other U.S. and worldwide patents
issued & pending. DTS and DTS Digital Out are
registered trademarks and the DTS logos and
Symbol are trademarks of DTS, Inc.
©1996-2007 DTS, Inc. All Rights Reserved.
9
When you turn on for the first
time
The menu for a language selection will appear when
you turn on the unit for the first time. You must select
a language to use the unit. Use b / B / v / V to select
a language then press ENTER and the confirm menu
will appear. Use b / B to select [Enter] then press
ENTER.
Displaying Disc Information
on-screen
You can display various information about the disc
loaded on-screen.
Initial Settings
By using the Setup menu, you can make various
adjustments to items such as picture and sound.
You can also set a language for the subtitles and the
Setup menu, among other things. For details on each
Setup menu item, see pages 11 to 12.
To display and exit the Menu:
Press SETUP to display the menu. A second press of
SETUP will take you back to initial screen.
To go to the next level:
Press B on the remote control.
To go back to the previous level:
Press b on the remote control.
1. Press DISPLAY to show various playback
information.
The displayed items differ depending on the disc
type or playing status.
General Operation
1. Press SETUP.
The Setup menu appears.
2. You can select an item by pressing v / V and
change or select the setting by pressing b / B.
• Title (Track) – Current title (or track).
number/total number of titles (or tracks).
• Chapter – Current chapter number/total number
of chapters.
• Time – Elapsed playing time.
• Audio – Selected audio language or channel.
• Subtitle – Selected subtitle.
• Angle – Selected angle/total number of angles.
Note:
If any button is not pressed for a few seconds, the onscreen display disappears.
10
2. Use v / V to select the desired option then press
B to move to the second level. The screen shows
the current setting for the selected item, as well as
alternate setting(s).
3. Use v / V to select the second desired option and
then press B to move to the third level.
4. Use v / V to select the desired setting then press
ENTER to confirm your selection.
Some items require additional steps.
5. Press SETUP or PLAY (N) to exit the Setup
menu.
LANGUAGE
Display Mode
Introduction
The Display Mode setting works only when the TV
Aspect mode is set to 4:3.
Letterbox – Displays a wide picture with bands on
the upper and lower portions of the screen.
Panscan – Automatically displays the wide picture
on the entire screen and cuts off the portions that
do not fit.
Progressive Scan
Disc Audio / Subtitle / Menu
Select the language you prefer for the audio track
(disc audio), subtitles, and the disc menu.
Original – Refers to the original language in which
the disc was recorded.
Other – To select another language, press
numeric buttons and then ENTER to enter the
corresponding 4-digit number according to the
language code list on the page 20. If you enter the
wrong language code, press CLEAR.
Off (for Disc Subtitle) – Turn off Subtitle.
Installation and Setup
Select a language for the Setup menu and then
on-screen display.
To Turn ON progressive scan:
Connect component video out of this unit to the input
of your TV or monitor, set your TV or monitor to
Component Input.
1. Select “Progressive Scan” on the DISPLAY menu
then press B.
2. Select “On” using the v / V buttons.
3. Press ENTER to confirm your selection.
The confirm menu will appear.
4. When the confirm menu appears on your screen
Cancel is highlighted as default. Use the b / B
buttons to highlight Enter.
Operation
Menu Language
Progressive Scan Video provides the highest quality
pictures with less flickering.
If you are using the Component Video jacks for
connection to a TV or a monitor that is compatible
with a progressive scan signal, set Progressive Scan
to On.
5. Pressing ENTER will set the player to Progressive
scan mode.
DISPLAY
TV Output Select
Set the player’s TV Output Select options according to
the TV connection type.
S-Video – When your TV is connected with the SVIDEO OUTPUT jack.
Reference
YPbPr – When your TV is connected with the
COMPONENT / PROGRESSIVE SCAN OUTPUT
jacks on the DVD player.
TV Aspect
4:3 – Select when a standard 4:3 TV is connected.
16:9 – Select when a 16:9 wide TV is connected.
11
AUDIO
OTHERS
Each DVD disc has a variety of audio output options.
Set the player’s AUDIO options according to the type
of audio system you use.
PBC
Set Playback Control (PBC) to On or Off.
Dolby Digital / DTS / MPEG
Bitstream – Select “Bitstream” if you connect this
unit’s DIGITAL OUTPUT jack to an amplifier or
other equipment with a Dolby Digital, DTS or
MPEG decoder.
PCM (for Dolby Digital / MPEG) – Select when
connected to a two-channel digital stereo amplifier.
DVDs encoded in Dolby Digital, MPEG will be
automatically downmixed to two-channel PCM
audio.
Off (for DTS) – If you select “Off”, the DTS signal
is not output through the DIGITAL OUTPUT jack.
Sample Freq. (Frequency)
If your receiver or amplifier is NOT capable of
handling 96 kHz signals, select 48 kHz. When this
choice is made, this unit automatically converts any
96 kHz signals to 48 kHz so your system can decode
them.
If your receiver or amplifier is capable of handling 96
kHz signals, select 96 kHz.
Check the documentation for your amplifier to verify
its capabilities.
DRC (Dynamic Range Control)
With the DVD format, you can hear a program’s
soundtrack in the most accurate and realistic
presentation. However, you may wish to compress the
dynamic range of the audio output (the difference
between the loudest sounds and the quietest ones).
This allows you to listen to a movie at a lower volume
without losing clarity of sound.
Set DRC to On for this effect.
Vocal
Set to On only when a multi-channel karaoke DVD is
playing. The karaoke channels on the disc mix into
normal stereo sound.
12
On: Video CDs with PBC are played according to
the PBC.
Off: Video CDs with PBC are played in the same
way as Audio CDs.
B.L.E. (Black Level Expansion)
To select the black level of playback pictures.
Set your preference and monitor’s ability.
On: Expanded grey scale. (0 IRE cut off)
Off: Standard grey scale. (7.5 IRE cut off)
Note:
The B.L.E. function works NTSC system only.
Operation
Introduction
General Features
Discs
Operations
OPEN/CLOSE (Z)
Opens or closes the disc tray.
ALL
PAUSE/STEP (X)
During playback, press PAUSE/STEP (X) to pause
playback.
ALL
Press PAUSE/STEP (X) repeatedly to play Frame-byFrame.
DVD
VCD
During playback, press SKIP (. or >) to go to the
next chapter/track or to return to the beginning of the
current chapter/track.
DVD
VCD
MP3
WMA
During playback, press SCAN (m or M) repeatedly to
select the required scan speed.
DVD : 4 steps
Video CD, MP3/WMA, Audio CD : 3 steps
DVD
VCD
MP3
WMA
While the playback is paused, press SCAN (M)
repeatedly to play in slow motion.
DVD, Video CD : 4 steps (Forward only)
DVD
VCD
During playback, press REPEAT repeatedly to select a
desired repeat mode.
DVD : Chapter/Title/Off
Video CD, Audio CD, MP3/WMA discs : Track/All/Off
DVD
VCD
MP3
WMA
A-B
Press the A-B button one at a time to select a point A and
point B and repeats a sequence from point A (Starting
point) to point B (End point).
DVD
VCD
ZOOM
During playback or pause mode, press ZOOM to enlarge
the video image.
You can move through the zoomed picture using
b / B / v / V buttons. Press CLEAR to exit.
DVD
VCD
RANDOM
During playback or in stop mode, press RANDOM for
random playback.
ACD
TITLE
If the current DVD title has a menu, the title menu
appears on the screen. Otherwise, the disc menu may
appears.
DVD
DVD MENU
The disc menu appears on the screen.
DVD
SKIP (. / >)
ACD
Installation and
Setup
Buttons
Press SKIP (.) twice briefly to step back to the
previous chapter/track.
ANGLE (
)
SUBTITLE (
AUDIO (
During playback of DVD disc that contains scenes
recorded at different camera angles, press ANGLE (
repeatedly to select a desired angle.
)
)
During playback, press SUBTITLE (
select a desired subtitle language.
MP3
ACD
Operation
REPEAT
ACD
ACD
WMA
Reference
SCAN (m / M)
DVD
)
) repeatedly to
During playback, press AUDIO (
) repeatedly to hear
a different audio language, audio channel or encoding
method.
DVD
DVD
VCD
13
Notes on general features:
Last Scene Memory
• On a Video CD with PBC, you must set PBC to Off
on the setup menu to use the repeat function (See
“PBC” on page 12).
This player memorizes last scene from the last disc
that is viewed. The last scene remains in memory
even if you remove the disc from the player or switch
off the player. If you load a disc that has the scene
memorized, the scene is automatically recalled.
• If you press SKIP (>) once during Repeat Chapter
(Track) playback, the repeat playback cancels.
• Zoom may not work on some DVDs.
• When you are playing a DVD disc that contains
scenes recorded at different camera angles, the
angle indicator will be displayed on the TV screen
during the operations as an indication that angle
switching is possible.
Additional Features
Time Search
DVD
VCD
To start playing at any chosen time on the disc:
1. Press DISPLAY during playback.
2. Press v / V to select the time clock icon and
“-:--:--” appears.
3. Input the required start time in hours, minutes, and
seconds from left to right. If you enter the wrong
numbers, press CLEAR to remove the numbers
you entered. Then input the correct numbers.
4. Press ENTER to confirm.
Playback starts from the selected time.
Marker Search
DVD
VCD
To enter a Marker
You can start playback from up to nine memorized
points. To enter a marker, press MARKER at the
desired point on the disc. The Marker icon appears on
the TV screen briefly. Repeat to enter up to nine
markers.
To Recall or Clear a Marked Scene
1. During disc playback, press SEARCH. The marker
search menu appears on the screen.
2. Within 9 seconds, press b / B to select a marker
number that you want to recall or clear.
3. Press ENTER and playback starts from the marked
scene. Or, Press CLEAR and the marker number is
erased from the list.
4. You can play any marker by inputting its number on
the marker search menu.
14
DVD
VCD 1.1
ACD
Note:
This player does not memorize the scene of a disc if
you switch off the player before commencing to play
the disc.
Screen Saver / Auto Power Off
The screen saver appears when you leave the DVD
player in Stop mode for about five minutes. If the
Screen Saver is displayed for five minutes, the DVD
Player automatically turns itself off.
System Select
You must select the appropriate system mode for your
TV system. If “NOdSC (No Disc)” appears in the
display window, press and hold PAUSE/STEP (X) for
more than 5 seconds to be able to select a system
(PAL, NTSC or AUTO).
This unit can play Audio CDs or MP3/WMA files.
MP3/ WMA/ Audio CD
Once you insert an MP3/WMA files recorded media or
Audio CD, a menu appears on the TV screen.
Use v / V to select a track/file and then press
PLAY (N) or ENTER and playback starts.
You can use variable playback functions.
Refer to page 13-14.
ID3 TAG
When playing a file containing information such as
track titles, you can see the information by pressing
DISPLAY. [ TITLE, ARTIST, ALBUM, YEAR,
COMMENT ]
Tips:
• If you are in a file list and want to return to the
previous Folder list, use v / V buttons to highlight
and press ENTER.
• Press DVD MENU to move to the next page.
• On a DISC with MP3/WMA and JPEG file, you can
switch MUSIC and PHOTO menu. Press TITLE, and
MUSIC or PHOTO word on top of the menu is
highlighted.
MP3 / WMA disc compatibility with this player is
limited as follows:
• Sampling frequency: within 8 - 48 kHz (MP3),
within 32 - 48kHz (WMA)
• Bit rate: within 8 - 320kbps (MP3),
32 - 192 kbps (WMA)
• The player cannot read an MP3/WMA file that has
a file extension as non than “.mp3” / “.wma”.
• CD-R/RW, DVD±R/RW Format: ISO 9660
• File names should have a maximum of 8 letters
and must incorporate an .mp3 or .wma extension.
Operation
Playing an Audio CD or
MP3/WMA file
• They should not contain special letters such as / ?
* : “ < > l etc.
• The total number of files in a disc should be less
than 650 files.
15
Programmed Playback
The program function enables you to store your
favorite tracks from any disc in the player memory.
A program can contain 30 tracks.
1. Insert an Audio CD or MP3/WMA files recorded
media. AUDIO CD or MUSIC menu appears.
2. Press PROGRAM and the
E
mark will appear.
Repeat Programmed Tracks
Press REPEAT to select a desired repeat mode.
• TRACK: Repeats the current track.
• ALL: Repeats all the tracks on programmed list.
• Off (No display): Does not play repeatedly.
Note:
If you press SKIP (>) once during Repeat Track
playback, the repeat playback cancels.
Note:
Press PROGRAM again to exit the program edit
mode, then the
E
mark will disappear.
Erasing a Track from Program List
3. Select a track on the “List” and then press ENTER
to place the selected track on the “Program” list.
Repeat to place additional tracks on the list.
1. During stop mode, press PROGRAM and the
mark will appear
4. Use b / B / v / V to select the track you want to
start playing on the “Program” list.
2. Use b / B / v / V to select the track that you wish
to erase from the Program list.
5. Press PLAY (N) or ENTER to start.
Playback begins in the order in which you
programmed the tracks. Playback stops after the
last track on the “Program” list have played.
3. Press CLEAR. Repeat step 1-3 to erase additional
tracks on the list.
6. To resume normal playback from programmed
playback, select a track on the list and then press
PLAY (N).
Erasing the Complete Program List
1. During stop mode, press PROGRAM and the
mark will appear
E
E
2. Use b / B / v / V to select “Clear All” and then
press ENTER.
Note:
The programs are also cleared when the power is
off or the disc is removed.
16
Moving to another file
Viewing a JPEG file
This unit can play JPEG files.
1. Insert a JPEG files recording media.
The PHOTO menu appears on the TV screen.
Press SKIP (. or >) or cursor (b or B) once
during viewing a picture to advance to the next or
previous file.
Zoom
During watching pictures, press ZOOM to enlarge the
video image. You can move through the zoomed
picture using b / B / v / V buttons.
Rotating the picture
Press v / V during showing a picture to rotate the
picture clockwise or counter clockwise.
Listening to MP3 music while watching picture
3. If you want to view a particular file, press v / V to
highlight a file and press ENTER or PLAY (N).
4. To return to the PHOTO menu while watching
pictures, press STOP (x).
Tips:
• If you are in a file list and want to return to the
previous Folder list, use v / V buttons to highlight
and press ENTER.
• Press DVD MENU to move to the next page.
• There are three Slide Speed options:
>>> (Fast), >> (Normal) and > (Slow).
Use b / B / v / V to highlight
. Then, use b / B
to select the option you want to use.
• On a DISC with MP3/WMA and JPEG file, you can
switch MUSIC and PHOTO menu. Press TITLE, and
MUSIC or PHOTO word on top of the menu is
highlighted.
• While watching a picture, press RETURN (O) to
hide the help menu.
2. Press TITLE to display the PHOTO menu.
3. Press v / V to select a photo file.
4. Use B to select
Playback starts.
icon then press ENTER.
5. To return to the PHOTO menu while watching
pictures, press STOP (x).
Tip:
To listen to only the desired music while watching
picture, program the desired files from the “MUSIC”
menu and then proceed as above.
JPEG disc compatibility with this player is
limited as follows:
• Photo size: Less than 2 MB recommended.
• Depending upon the size and the number of
JPEG files, it could take a long time for the DVD
player to read the disc’s contents. If you do not
see an on-screen display after several minutes,
some of the files may be too large — reduce the
resolution of the JPEG files to less than 5 million
pixels and burn another disc.
• The total number of files in a disc should be less
than 650 files.
Slide Show
Use b / B / v / V to highlight the
then press ENTER.
1. Insert the disc containing the two types of file in
the player.
Operation
2. Press v / V to select a folder, and press ENTER.
A list of files in the folder appears.
(Slide Show)
• Some discs may be incompatible due to a
different recording format or the condition of disc.
Still Picture
• Ensure that all the selected files have the “.jpg”
extensions when copying into the CD layout.
1. Press PAUSE/STEP (X) during slide show.
The player will now go into pause mode.
• CD-R/RW, DVD±R/RW Format: ISO 9660
2. To return to the slide show, press PLAY (N) or
press PAUSE/STEP (X) again.
• If the files have “.jpe” or “.jpeg” extensions, please
rename them as “.jpg” file.
• File names without “.jpg” extension will not be
able to be read by this unit. Even though the files
are shown as JPEG image files in Windows
Explorer.
17
Playing a DVD VR format Disc
This unit will play DVD-RW disc that is recorded
using the Video Recording (VR) format.
1. Insert a disc and close the tray.
The DVD-VR menu appears on the TV screen
2. Press v / V to select a title then press
PLAY (N) or ENTER and playback starts.
3. Press DVD MENU to move to the list menu.
Notes:
• This unit will play DVD-R/RW disc that is recorded
using the DVD-Video format that have been
finalized using a DVD-recorder. Unfinalized
DVD-R/RW discs cannot be played in this player.
• Some DVD-VR disc are made with CPRM data by
DVD RECORDER. Player does not support these
kinds of discs.
What is CPRM?
CPRM is a copy protection system (with scramble
system) only allowing the recording of ‘copy once’
broadcast programs. CPRM stands for Content
Protection for Recordable Media
18
Reference
Remote Control Function
Note:
Remote Control C1/C2/C3 Code Switching
This unit is initially set to C3 code (JVC DVD
PLAYER code). You can easily change the
Remote Control code to C1 (JVC VCR code), C2
(JVC DVD RECORDER code) or C3 as shown
below.
If you change the batteries of the Remote Control with
C1 or C2 code, the remote control code is set to C3
automatically. In this case, you should reset the
remote control code described above.
STANDBY/ON
x
Maintenance and Service
Refer to the information in this chapter before
contacting a service technician.
Handling the Unit
ENTER
When shipping the unit
Please save the original shipping carton and packing
materials. If you need to ship the unit, for maximum
protection, re-pack the unit as it was originally packed
at the factory.
1-3
Keeping the exterior surfaces clean
• Do not use volatile liquids such as insecticide spray
near the unit.
• Do not leave rubber or plastic products in contact
with the unit for a long period of time. since they
leave marks on the surface.
Cleaning the unit
To clean the player, use a soft, dry cloth. If the
surfaces are extremely dirty, use a soft cloth lightly
moistened with a mild detergent solution.
1. Press the number Key “1” for C1, “2” for C2 or
“3” for C3 to change the remote control code.
2. Press STANDBY/ON (1/\) to turn on the unit.
3. Press x on the unit for over 5 seconds while the
unit is turned on. The code currently set appears
on the front display panel.
4. Press ENTER on the remote control to change the
unit's code. The code currently set on the remote
control is displayed on the front display panel for
approximately 5 seconds, and is applied to the
unit.
Maintaining the Unit
The unit is a high-tech, precision device. If the optical
pick-up lens and disc drive parts are dirty or worn, the
picture quality could be diminished.
Reference
• Keep pressing ENTER down during step 1.
Do not use strong solvents such as alcohol, benzine,
or thinner, as these might damage the surface of the
unit.
Depending on the operating environment, regular
inspection and maintenance are recommended after
every 1,000 hours of use.
For details, please contact your nearest authorized
service center.
19
Language Codes
Use this list to input your desired language for the following initial settings:
Disc Audio, Disc Subtitle, Disc Menu.
20
Language
Code
Language
Code
Language
Code
Language
Code
Abkhazian
6566
Fiji
7074
Lingala
7678
Singhalese
8373
Afar
6565
Finnish
7073
Lithuanian
7684
Slovak
8375
Afrikaans
6570
French
7082
Macedonian
7775
Slovenian
8376
Albanian
8381
Frisian
7089
Malagasy
7771
Somali
8379
Ameharic
6577
Galician
7176
Malay
7783
Spanish
6983
Arabic
6582
Georgian
7565
Malayalam
7776
Sudanese
8385
Armenian
7289
German
6869
Maltese
7784
Swahili
8387
Assamese
6583
Greek
6976
Maori
7773
Swedish
8386
Aymara
6588
Greenlandic
7576
Marathi
7782
Tagalog
8476
Azerbaijani
6590
Guarani
7178
Moldavian
7779
Tajik
8471
Bashkir
6665
Gujarati
7185
Mongolian
7778
Tamil
8465
Basque
6985
Hausa
7265
Nauru
7865
Tatar
8484
Bengali; Bangla
6678
Hebrew
7387
Nepali
7869
Telugu
8469
Bhutani
6890
Hindi
7273
Norwegian
7879
Thai
8472
Bihari
6672
Hungarian
7285
Oriya
7982
Tibetan
6679
Breton
6682
Icelandic
7383
Panjabi
8065
Tigrinya
8473
Bulgarian
6671
Indonesian
7378
Pashto, Pushto
8083
Tonga
8479
Burmese
7789
Interlingua
7365
Persian
7065
Turkish
8482
Byelorussian
6669
Irish
7165
Polish
8076
Turkmen
8475
Cambodian
7577
Italian
7384
Portuguese
8084
Twi
8487
Catalan
6765
Japanese
7465
Quechua
8185
Ukrainian
8575
Chinese
9072
Javanese
7487
Rhaeto-Romance 8277
Urdu
8582
Corsican
6779
Kannada
7578
Rumanian
8279
Uzbek
8590
Croatian
7282
Kashmiri
7583
Russian
8285
Vietnamese
8673
Czech
6783
Kazakh
7575
Samoan
8377
Volapük
8679
Danish
6865
Kirghiz
7589
Sanskrit
8365
Welsh
6789
Dutch
7876
Korean
7579
Scots Gaelic
7168
Wolof
8779
English
6978
Kurdish
7585
Serbian
8382
Xhosa
8872
Esperanto
6979
Laothian
7679
Serbo-Croatian
8372
Yiddish
7473
Estonian
6984
Latin
7665
Shona
8378
Yoruba
8979
Faroese
7079
Latvian, Lettish
7686
Sindhi
8368
Zulu
9085
Troubleshooting
Possible Cause
Correction
No power.
• The power cord is disconnected.
• Plug the power cord into the wall outlet
securely.
The power is on, but
the DVD player does
not work.
• No disc is inserted.
• Insert a disc. (Check the disc indicator
in the display window is lit.)
No picture.
• The TV is not set to receive DVD
signal output.
• Select the appropriate video input
mode on the TV.
• The video cable is not connected
securely.
• Connect the video cable securely.
• The [TV Output Select] options is set
to the wrong position on the setup
menu for the S-VIDEO or
COMPONENT VIDEO connection.
• Set the [TV Output Select] option to
the correct position on the setup menu
regarding to the current video
connection. (See page 11)
• The equipment connected with the
audio cable is not set to receive DVD
signal output.
• Select the correct input mode of the
audio receiver so you can listen to the
sound from the DVD player.
• The power of the equipment
connected with the audio cable is
turned off.
• Turn on the equipment connected with
the audio cable.
• The AUDIO options are set to the
wrong position.
• Set the AUDIO option to the correct
position, then turn on the DVD player
again by pressing STANDBY/ON.
• An unplayable disc is inserted.
• Insert a playable disc. (Check the disc
type and regional code.)
No sound.
The DVD player does
not start playback.
• The remote control is not pointed at
The remote control
the remote sensor on the DVD player.
does not work properly.
• Point the remote control at the remote
sensor of the DVD player.
• The remote control is too far from the
DVD player.
• Operate the remote control closer to
the DVD player.
• The current remote control code does
not match the unit.
• Identify the remote control code with
the code of unit. (See page 19).
Reference
Symptom
21
Specifications
General
Power requirements:
AC 110-240 V, 50/60 Hz
Power consumption:
8W
Dimensions (Approx.):
430 x 39 x 192 mm (17 x 1.5 x 7.6 inches) (W x H x D) without foot
Net weight (Approx.):
1.5 kg (3.3 lbs)
Operating temperature:
5 °C to 35 °C (41 °F to 95 °F)
Operating humidity:
5 % to 90 %
Outputs
VIDEO OUTPUT:
1.0 V (p-p), 75 Ω, sync negative, RCA jack x 1
S-VIDEO OUTPUT:
(Y) 1.0 V (p-p), 75 Ω, negative sync, Mini DIN 4-pin x 1
(C) 0.3 V (p-p) 75 Ω
COMPONENT VIDEO OUTPUT:
(Y) 1.0 V (p-p), 75 Ω,negative sync, RCA jack x 1
(Pb)/(Pr) 0.7 V (p-p), 75 Ω, RCA jack x 2
AUDIO OUTPUT:
2.0 Vrms (1 KHz, 0 dB), 600 Ω, RCA jack (L, R) x 1
DIGITAL OUTPUT (COAXIAL):
0.5 V (p-p), 75 Ω, RCA jack x 1
System
Laser:
Semiconductor laser, wavelength 650 nm
Signal system:
PAL/NTSC
Frequency response:
DVD (PCM 96 kHz): 8 Hz to 44 kHz
DVD (PCM 48 kHz): 8 Hz to 22 kHz
CD: 8 Hz to 20 kHz
Signal-to-noise ratio:
More than 90 dB (ANALOG OUT connectors only)
Harmonic distortion:
Less than 0.02 %
Dynamic range:
More than 95 dB (DVD/CD)
Accessories
Video cable (1), Audio cable (1), Remote control (1), Batteries (2)
Note: Design and specifications are subject to change without prior notice.
22
Reference
MEMO
23
XV-N380B / XV-N382S
EN
0209SKMLGEEGL
P/N: MFL62178436
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising