LG BX220-JD Owner's Manual

LG BX220-JD Owner's Manual
Please read this manual
carefully
before
operating
your set.
Retain it for future reference.
Record model number and serial number of the set.
See the label attached
on
the bottom of the set and
quote this information to your dealer when you
require service.
Model number
:
Serial number
:
LGDPROJECT
BX220-JD
OWNER'S MANUAL
DLP PROJECTOR
FCC NOTICE
?
A Class A digital device
This equipment has been tested and found to
comply with the limits for a Class A digital device, purare designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
suant to Part 15 of the FCC Rules. These limits
Warning
This is
which
a
class A
case
the
product.
user
In
may be
a
domestic environment this
required
to take
adequate
product
may
measures.
cause
radio
interference, in
Contents
Contents
Introduction
Safety
Instructions ..........................................4-6
Screen Menu
Options
Auto
Function ...................................25
Tracking
Clock / Phase Function ...................................25
Names of parts
Screen Position ...............................................25
Main
Body .......................................................7
Connecting Part ..............................................7
RS-232C
Control Panel ..................................................8
External Control Device
Remote Control ...............................................9
Information
Installing
Projector
Batteries ...........................................9
Supported
Status Indicators ..............................10
Monitor
Setup........................26
Display..............................31
Maintenance....................................................32
Accessories .....................................................11
Memo ..............................................................33
Extras ...............................................11
Specifications ..................................................35
Optional
Installing
and
Composition
Installation Instructions ...................................12
Basic
Operation of the Projector .....................13
Using Kensington Security System .................14
Turning on the Projector .................................15
Turning off the Projector .................................15
Focus and Position of the Screen Image........16
Selecting source mode ...................................16
Connection
Connecting
Connecting
Connecting
Connecting
Connecting
PC ..........................17
to
a
Desktop
to
a
Notebook PC ........................17
to
a
Video Source ........................18
to
a
DVD ......................................18
to
a
D-TV
Set-Top
Box ................18
Function
Video Menu
Options
Adjusting Video ...............................................19
APC (Auto Picture Control) .............................19
Auto Color Temperature Control .....................20
White Peaking Function ..................................20
Gamma Function ............................................20
Special Menu Options
Selecting language .........................................21
Flip Horizontal Function ..................................21
Flip Vertical Function.......................................21
Using ARC Function........................................22
Using Keystone function .................................22
Auto Source Function .....................................22
Using Blank function .......................................23
Selecting Blank Image color ...........................23
Lamp Mode Function ......................................23
Checking lamp time ........................................24
Using Still function ..........................................24
Disposal
of your old
appliance
1. When this crossed-out wheeled bin
symbol is attached to a product it
by the European Directive 2002/96/EC.
All electrical and electronic products should be disposed of separately
from the municipal waste stream via designated collection facilities
appointed by the government or the local authorities.
The correct disposal of your old appliance will help prevent potential
negative consequences for the environment and human health.
For more detailed information about disposal of your old appliance,
please contact your city office, waste disposal service or the shop
where you purchased the product.
means
2.
3.
4.
the
product
is covered
3
Safety
Instructions
Instructions
Safety
Please take note of the
Instructions
Safety
WARNING
NOTES
After
safety
:
:
are
instructions to
given
prevent any potential accident
in two forms
as
The violation of this instruction may
this
projector.
detailed below.
The violation of this instruction may
reading
misuse of the
or
serious
cause
cause
light injuries
manual, keep it in the place that the
user
and
injuries
or
always
even
damage
can
death.
to the
contact
projector.
easily.
WARNING
Do not place the Projector in direct
sunlight or near heat sources such
as
radiators, fires and
This may
place
inflammable materi-
Do not allow children to
the installed
projector
stove etc.
This may
fire hazard !
cause a
Do not
als beside the
cause a
It may
fire hazard !
cause
ing injury
or
hang
on
projector.
the
projector
to
fall,
caus-
death.
NOTES
Disconnect from the mains and
all connections before
remove
Do not
to
moving.
place
sources
as a
the
projector
of steam
or
close
Do not
oil such
it
might
place the projector where
be exposed to dust.
humidifier.
This may
This may create a fire hazard
electric shock hazard !
When
the
installing
table, be careful
near
the
projector
place
not to
Only
it
and stable surface.
edge.
adult and serious
a
damage
projector
on a
level
be
operation.
nal
than 20cm/8 inches.
temperature may
cause a
fire
hazard!
Do not block the vents of the proor restrict air-flow in any way.
cause
more
An excessive increase in its inter-
suitable stand.
the internal
ture to increase and could
fire hazard !
Ensure good ventilation around the
projector. The distance between
the projector and the wall should
to the
jector
This would
use
It may become unstable and affect
This may cause the projector to fall
causing serious injury to a child or
projector.
Only use
the
on a
cause a
or an
tempera-
cause a
fire
Do not
place
the
projector directly
on a
carpet, rug
or
place
where
ventilation is restricted.
This would
cause
its internal
temperature
to increase and
might
create
a
fire
hazard !
hazard!
WARNING
Do not
use
This may
the
cause a
projector
fire
or an
in
a
damp place
such
as a
bathroom where it is
likely
to
get
wet.
electric shock hazard !
WARNING
Earth wire should be connected.
If the earth wire is not connected, there is a
possible danger of electric shock caused by
the current leakage.
If grounding methods are not possible, a
separate circuit breaker should be employed
and installed by a qualified electrician.
Do not connect ground to telephone wires,
lightning rods or gas pipe.
4
The mains
ed
avoid
plug
should be insert-
into the power outlet to
fire hazard !
fully
a
This may
cause a
fire hazard !
Do not
place heavy objects
on
the power cord
This may cause
shock hazard !
a
fire
or an
electric
Safety
Instructions
WARNING
Do not
use
too many
It may result in
plugs
overheating
on
the Mains multi-outlet.
of the outlet and
fire hazard !
causes a
NOTES
Never touch the power
wet hand
plug
with
Hold the
This may
hazard !
cause an
electric shock
This may
Do not
plug when the power cord
plug is damaged or the
connecting part of the power outor
Do not turn the
(Do
not
It may
hot
or an
objects
electric
projector On/Off by plugging-in
plug for switch.)
or
a
collecting on
plug pins or outlet.
This may
cause a
the
fire hazard !
fire hazard !
such
This may cause
shock hazard !
Prevent dust
power
as a
fire
heater.
or an
unplugging
Place the
will not
projector where people
trip or tread on the power
lead.
electric
This may cause
shock hazard !
the power
plug
a
fire
or an
electric
to the wall outlet.
the power
use
cause
fire
cause a
come
let is loose.
a
unplug-
Ensure the power cord does not
into contact with sharp or
the
This may cause
shock hazard !
when
plug firmly
If you pull the cord the cord
may be damaged.
ging.
a
mechanical failure
or
could
give
an
electric shock.
WARNING
Do not place anything containing
liquid on top of the projector such
as flowerpot, cup, cosmetics or
In
candle.
This may
cause a
case
of
impact
This may
hazard !
cause an
cen-
a
This may
ard !
doctor
In the
fire
or an
lens
any
batteries
In the event that
care-
image does
please
switch it off and unplug it from
the mains supply and contact
your Service Agent.
not appear
of a battery being
by a child please consult
immediately.
case
swallowed
covers
cover). High
risk of
Electric Shock!
electric shock
electric
a
on
This may cause
shock hazard !
remove
an
the
a
screen
fire
Don't look
onto the lens
Do not touch metal
when the
is in
soon
damage
directly
projector
to fall
objects
let and contact your service
Dispose of used
fully and safely.
electric shock haz-
Do not allow any
projector.
If water is spilt into the projector
unplug it from the mains supply
outlet immediately and consult
your Service Agent.
Do not
dam-
into the
This may cause
shock hazard !
(except
or
ter.
fire hazard !
cause an
shock
age to the projector switch it off
and unplug it from the mains out-
use.
Eye
after
vents and
may occur!
or an
electric
parts during
operation
lamp cover
since
or
the
will remain
very hot!
CAUTION
concerning the Power Cord
appliances recommend they be placed upon a dedicated circuit; that is,a single outlet circuit which
powers only that appliance and has no additional outlets or branch circuits.Check the specification page
Most
of this owner's manual to be certain.
Do not overload wall outlets. Overloaded wall
outlets,loose
or
damaged
wall
outlets, extension cords,
power cords,or damaged or cracked wire insulation are dangerous.Any of these conditions could
result in electric shock or fire. Periodically examine the cord of your appliance,and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced
frayed
with
an
exact
replacement part by
an
authorized servicer.
Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched,
closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the
cord exits the
appliance.
5
Safety
Instructions
WARNING
Never touch the wall outlet when
Do not
drop
there is
impact
shock.
of gas, open the
windows and ventilate.
leakage
This may
the
or
allow
Don't look at laser beam directly
it can cause eye damage!
as
mechanical failure
cause
personal injury
Itcancauseafireoraburnbya
spark.
projector
or
!
NOTES
Do not
top
of
place heavy objects
Take
on
projector.
This may
cause
not to
care
cause
the lens
the
mechanical failure
particularly
projector.
impact to
moving
Do not touch the lens of the prodelicate and easily
when
jector. It is
damaged.
or
personal injury!
Do not
use
sharp
any
tools
on
the
projector
as
this will
damage
the
casing.
WARNING
Do not
the
use
water while
cleaning
projector
This may
projector
cause
or an
In the
a
damage
unlikely
event of smoke
tor, switch it off
to the
electric shock hazard.
Use an air spray or soft cloth that
is moist with a neutral detergent
or
strange smell from the projec,
it from
unplug
and water for
the wall outlet and contact your
dealer or service centre.
This may cause
shock hazard !
a
fire
or an
stains
on
the
removing
projection
dust
or
lens.
electric
NOTES
Contact the Service Center
once
year to clean the internal
of the projector.
parts
a
Accumulated dust
can cause
Unplug this product from the wall outlet
liquid cleaners or aerosol cleaners.
This may
cause
damage
to the
Projector
before
cleaning.
or cause an
Do not
use
electric shock hazard !
mechan-
ical failure.
WARNING
Do not
attempt
This may
cause
to service the
damage
to the
projector yourself.
projector
and could
Contact your dealer
give
an
electric Shock
as
or
well
service centre.
as
invalidating
the
warranty !
NOTES
Be
sure
to
unplug
if the
is not to be used for
a
projector
long peri-
Refer
od.
Accumulated dust may
hazard!
Only
use
This could
6
the
cause a
fire
specified type
of
cause
damage
lamp servicing
personnel.
service
to
qualified
Do not mix
new
batteries with old
batteries.
This may cause the batteries to
heat and leak.
battery.
to the remote control.
over-
Names of
parts
ENGLISH
Names of parts
Main
*
Body
The
projector is manufactured using high-precision technology. You may, however, see on the Projector
tiny black points and/or bright points (red, blue, or green). This can be a normal result of the
manufacturing process and does not always indicate a malfunction.
screen
Rear remote control
Control
Zoom
panel
sensor
ring
Focus
Power button
ring
Indicators
Foot
OP
W
E
R
adjusting
button
A
TU
O
L
OV
M
U EN
KO
L
OV
OS
RU
EC
Front remote control
Lens
*
Foot
adjusting
cover
Push the lens
front.
button
cover
Connecting
DVI
sensor
cover into the inside after pulling it open into the
you mount on the ceiling, after pushing the cover, the lens
is installed. If not, the cover may overlap projecting lens.)
(If
Part
Input
S-Video
RGB Input
(PC/DTV)
RS-232C
Video
AC IN
Kensington Security
System Connector
(Refer to page 14)
7
Names of
parts
Control Panel
/
,
KEYSTONE+/- Button
MENU
Selects
or
closes
SOURCE
KEYSTONE
MENU Button
SOURCE Button
Switches to RGB, DVI, Video,S-Video mode.
menus.
/
Button
Adjusts
AUTO Button
A
KEYSTONE
AUTO
OK
POWER
8
menus.
OK Button
Checks
saves
POWER Button
functions of
present mode and
change of functions.
the
Names of
parts
ENGLISH
Remote Control
POWER
POWER Button
MENU
KEYSTONE
SOURCE
MENU Button
SOURCE Button
KEYSTONE+/-,
F/GButton
AUTO Button
BLANK Button
(Refer
(Refer
to
to
p.25)
A
AUTO
KEYSTONE
BLANK
LASER
D / EButton
OK Button
OK
ARC Button
p.23)
(Refer
to
p.22)
ARC
STILL Button
(Refer
to
p.24)
STILL
LASER Button
*
Produces
screen
(Don't
a
can cause
Installing
bright
red laser
pointer
on
the
for the purpose of indication.
look at laser beam directly as it
eye
damage!)
Batteries
?
Open
the
battery compartment
cover on
the back of the
remote control and insert the batteries with correct
match "+" with
?
"+", and match
"-"
polarity,
with "-".
Install two 1.5V "AAA" batteries.
Don't mix used batteries with
new
batteries.
9
Names of
parts
Projector
*
Status Indicators
Lamp Indicator, operation
projector.
indicator and
temperature indicator
at the
top of the projector show the
user
the
operating
status
of the
Lamp
Operation
OP
W
E
R
Indicator
Indicator
Temperature
Indicator
A
U
T
O
OV
L
EM
N
U
O
K
V
O
L
S
O
U
R
EC
Orange
Green(flashing)
Operation
Indicator
Standby.
Lamp cooling until the lamp turn on.
Green
On operation. (Turn on the lamp)
Orange(flashing) Projector lamp is cooling as power out (2 minutes)
Off
Power off.
Red
Lamp
Indicator
Red(flashing)
Green(flashing)
Orange
Temperature
Indicator
Red
Red
10
Projector lamp is reaching the end of its life and needs
replaced with a new lamp. (over 2000 hours)
The projector has trouble in the lamp or around it at
power-on. Retry Power On again later. If lamp indicator
is red (flashing) again, contact the service center.
The lamp cover is not closed.
This projector is in high temperature. Turn the power of
projector off and check the ventilator.
The projector is turned off as its high temperature.
Power has turned off due to problem with the
internal cooling fan. Contact your service center.
to be
(flashing)
Names of
parts
ENGLISH
Accessories
POWER
MENU
KEYSTONE
AUTO
KEYSTONE
BLANK
LASER
SOURCE
OK
ARC
STILL
1.5V
1 5V
.
2 Batteries
Remote Control
Cable
Computer
Optional
*
Contact your dealer to
*
When
*
*
(size AAA)
RCA to D-Sub
Adaptor
Power Cord
Operating guide
Extras
purchase these items.
ceiling installer, use only the ceiling installer for projector.
Contact your service personnel for replacing a new lamp.
Projector lamp is reaching the end of its life and needs to be replaced with
applying
Video Cable
a
Projection
Screen
Portable
Bag
Lamp
S-Video Cable
a new
lamp.
SCART to RCA jack
(option)
Ceiling
installer for
projector
DVI-D Cable
RS-232C Cable
11
Installing
and
Composition
Installation and
Composition
Installation Instructions
*
Don't
place
the
projector
in the
conditions. It may
following
Provide proper ventilation for this
cause
malfunction
or
product damage.
projector.
The projector is equipped with ventilation holes(intake)
on the bottom and ventilation holes(exhaust) on the front.
do not block or place anything near these holes, or internal
heat build-up may occur, causing picture degradation or
damage to the projector.
Do not place the projector on a carpet, rug or other
similar surface. It may prevent a adequate ventilation
of the projector bottom. This product should be
mounted to a wall or ceiling only.
Never
Leave
push projector
projector.
Place this
Install this
spill liquid
in
in
a
adequate temperature
location where
place the projector
cause
of any kind into the
more)
projector
projector only
Don't
This may
or
overheating
where it
of the
and
adequate distance(30cm/12
projector.
inches
humidity conditions.
adequate temperature
can
an
around the
and
humidity
is available.
(refer p.35)
be covered with dust.
projector.
Do not obstruct the slots and
openings
of the
projector. This may
cause
overheating
and create
a
fire
hazard.
The
projector is manufactured using high-precision technology. You may, however, see tiny black points
bright points (red, blue, or green) that continuously appear on the projector Screen. This is a norresult of the manufacturing process and does not indicate a malfunction.
and/or
mal
To
display
projector.
If there is
12
DTV programs, it is necessary to connect
no
input signal, the
Menu will not be
a
DTV receiver
displayed
on screen.
(Set-top Box)
and connect it to the
or
Installing
Basic
of the
Operation
ENGLISH
projector
on a
2. Place the
projector
the correct distance from the
sturdy
and horizontal surface with the PC
determines the actual size of the
3. Position the
angle, the
page 22.)
Composition
Projector
1. Place the
screen
and
or
AV
source.
The distance between the
screen.
projector
and the
image.
projector so that the lens is set at a right angle to the screen. If the projector is not set at a right
image will be crooked. If this is so then the keystone adjustment may correct this (Refer to
screen
4. Connect the cables of the
projector
to
a
wall power socket and other connected
projection distance based
on
Projection
Screen
the
sources.
picture format
off-set ratio:100%
height (X)
Center line of lens
Projection
distance
4:3
(D)
picture
format
mm
/ inches
screen
size
40′′
60′′
80′′
90′′
100′′
110′′
120′′
150′′
200′′
610/24.0
914/36.0
1219/48.0
1372/54.0
1524/60.0
1676/66.0
1829/72.0
2286/90.0
3048/120.0
1400/55.1
2100/82.7
2800/110.2
3150/124.0
3500/137.8
3850/151.6
4200/165.4
5250/206.7
7000/275.6
1680/66.1
2520/99.2
3360/132.3
3780/148.8
4200/165.4
4620/181.9
5040/198.4
6300/248.0
8400/330.7
screen
height (X)
The shortest
distance
The
longest
(D)
distance
*
(D)
The
longest/shortest
distance show status when
adjusted by
the
zoom
function.
13
Installing
and
Composition
Using Kensington Security System
The
projector has a 'Kensington' Security System
Security system cable as below.
For the detailed installation and
to the
And
use
Kensington Security System
for
further
Kensington
information,
of the
Connector
Kensington Security System,
contact
http://www.kensington.com,
expensive electronic equipments
tors.
is
an
optional
item.
K
14
the back
panel.
Connect the
refer to the user's
'Kensington'
guide
attached
set.
company that deals with
Kensington Security System
on
the
such
internet
as
homepage
notebook PCs
or
of the
projec-
Installing
Turning
on
1. Connect power cord
2. Remove the lens
the
ENGLISH
correctly.
cover
of the
projector.
the remote control
on
indicator flashes
It will take about 12 second to
An
Composition
Projector
3. Press the POWER button
(Green operation
and
display
top
or
during cooling
cover.
of the
lamp.)
the
picture after power on because the
indicator light turns (Green).
projector lamp
has to
warm
up.
will appear after the operation
Select the source mode with the SOURCE button.
image
Leave the
cooling
*
Don't
projector plugged
in for at least 2 minutes after
to continue which will
unplug
help
to preserve the
the power cord while the ventilation fan
Turning
off the
lamp
switching
off the
projector,
(inlet/outlet)
is
working.
If so, you take
this will allow the
lamp
longer time by lamp
on.
Projector
1. Press the POWER button
on
the
top
cover or
remote control.
2. Press the POWER button
on
the
top
cover or
remote control
3. If the
as
life.
operation indicator LED is orange and blinking,
operation indicator LED is lit up constantly (orange).
again
to cut off the power.
do not disconnect the mains
If the operation indicator LED is orange and blinking, the power button
operate.
on
the
top
cover or on
supply
until the
the remote control will not
Power Off?
Please Press
Key Again.
15
Installing
and
Composition
Focus and Position of the Screen
When
image appears
an
on
Image
the screen, check if it is in focus and fits well to the
Zoom
screen.
ring
Focus
ring
P
O
W
ER
AU
TO
VO
L
M
EN
U
OK
V
OL
S
OU
RC
E
To
To
adjust the
adjust the
focus of the
size of the
image, rotate the focus ring which is the outer ring on the lens.
image, rotate the zoom ring which is the inner ring on the lens.
To raise
or lower the image on the
by pushing foot adjuster button as
1. While
the foot
pressing
raise
adjuster button,
2. Release the button to lock the foot in its
3. To fine-tune the
After
raising
height of the projector,
new
or
source
lower the
or
retract the foot at the bottom of the
projector to place
rotate the front foot to raise
on
the
or
lower it.
projector.
mode
1. Press the SOURCE button.
select
F
2. Each press of the
16
OK
RGB
F,
G
G button
the
position.
the front foot, do not press down
Selecting
screen, extend
below.
changes
RGB
DVI
S-Video
Video
the
display
as
below.
screen
image
in the proper
position.
projector
Connection
ENGLISH
Connection
to
Connecting
*
You
can
*
You
can use
*
*
connect the
a
Desktop
PC
computer of VGA, SVGA, XGA and SXGA output.
signals of the Aspect Ration 4:3. (For HD wide input signals, you cannot
Fundamentally, HD wide input signal is not included in the Spec, so the set may not support HD signal perfectly.
Refer to page 31 for the supported pc graphic card displays of the projector.
projector to
a
ARC function for the RGB
<
How to connect
a.
Connect
use
ARC
function.)
>
computer cable
to RGB
Input (PC/DTV)
of the
projector.
b. If the PC has DVI
of the
output,
connect DVI cable to DVI
Input
projector.
to
Connecting
<
How to connect
a.
Connect
a
Notebook PC
>
computer cable
to RGB
Input (PC/DTV)
of the
projector.
*
If you set your computer, such as a notebook type IBM PC/AT
compatible, to output the signal to both the display of your
computer and the external monitor, the picture of the external
monitor may not appear properly. In such cases, set the output
mode of your computer to output the signal only to the external
monitor. For details, refer to the operating instructions supplied
with your computer.
b. If the PC has DVI
of the
output,
connect DVI cable to DVI
Input
projector.
17
Connection
to
Connecting
*
You
can
connect
a
Video Source
VTR,
a
a
camcorder,
a
LDP
or
any other
compatible
video
image
source
to the
projector.
<Howtoconnect1>
a.
Connect the Video
jacks
of the A/V
input jacks
source
of the
projector to
the
output
<VCR>
with Video cable.
<Howtoconnect2>
S VIDEO
(R) AUDIO (L)
b. Connect the S-Video
S-Video
*
You
projector to
to the
projector.
to
DVD
source
a
output jacks (Y, PB, PR) of the DVD might be labelled
<
How to connect
a.
Connect the DVD
IN
Y, Pb, Pr / Y, B-Y, R-Y / Y, Cb, Cr according
as
When
to the
equipment.
>
Component cable to the RCA to D-Sub
Adaptor and then connect the RCA to D-Sub Adaptor to
RGB Input (PC/DTV) of the projector.
*
V ID EO
OUT
the
output jack of an A/V source with an S-Video cable.
get better picture quality when connecting
Connecting
The
of the
can
S-Video
*
input jack
connecting the component cable, match the jack
component cable.(Y=green, PB=blue, PR=red)
RCA to D-Sub
Adaptor
Component
colors
cable
with the
b. Use
a
DVD with
Connecting
*
*
Component 480i(576i)/480p(576p)
to
a
D-TV
Set-Top
mode.
<DVD>
(R) AUDIO (L)
Y
PB
PR
Box
To receive D-TV programmes, it is necessary to purchase a D-TV receiver (Set-Top Box) and
connect it to the projector.
Please refer to the owner's manual of the D-TV Set-Top Box for the connection between projector and
D-TV Set-Top Box.
<
How to connect
a.
Connect
an
RGB source
computer cable
to RGB
>
Input (PC/DTV)
of the
<D-TV
projector.
*
If the
Set-Top
Box has DVI
output,
use
Set-Top
(R)AUDO (L)
b. Use
*
It
a
can
DTV receiver with DTV
be
supported
<
How to connect
a.
Connect the D-TV
480p(576p)/720p/1080i
When
DTV OUTPUT
DVI OUTPUT
Y
PB
PR
mode.
the DVI/HDCP.
a
Component
source >
Set-Top Box Component cable to the
RCA to D-Sub Adaptor and then connect the RCA to D-Sub
Adaptor to RGB Input (PC/DTV) of the projector.
*
Box>
DVI cable.
connecting the component cable, match the jack
component cable.(Y=green, PB=blue, PR=red)
RCA to D-Sub
Adaptor
Component
cable
colors
with the
b. Use
a
DTV receiver with DTV
480p(576p)/720p/1080i
mode.
(R)AUDIO (L)
18
DTV OUTPUT
DVI OUTPUT
Y
PB
PR
Function
ENGLISH
Function
*
*
*
In this
manual, the OSD(On Screen Display) may be different from your Projector 's because it is just example to help with the Projector
operation.
If there is no input signal present, the Menu will not be displayed on the screen.
This operating guide explains operation of RGB(PC) mode mainly.
Video Menu
Adjusting
Options
Video
<RGBmode>
1. Press the MENU button and then
2. Press the OK
want to
(A)
adjust.
button and then
use
use
F,
D
,
G button to select the
E button to select
a
menu.
video item you
Contrast
50
Brightness
50
Color R
50
Color G
50
Color B
50
Reset
3. Press the
F,
G button to
adjust
the
screen
condition
as
you want.
MENU
menu options will not affect other input source.
adjustment of
menu options for the following input source :
required, re-adjust
Video/S-Video/Component (480i(576i)), Component (480p(576p), 720p, 1080i)
To restore the original image condition after changing it, press OK (A) button
after selecting [Reset] item.
In the broadcasting system NTSC, the picture item Tint is displayed and can
be adjusted.
To exit the menu display, repeatedly, press the MENU button.
prev.
Each
<
move
FG
Video mode
adjust
>
As
APC
*
*
Picture
(Auto
Use APC to set the
APC
FG
Clear
Contrast
80
Brightness
50
Color
50
Sharpness
50
MENU
prev.
move
FG select
Control)
projector for the
best
picture
appearance.
This function will not work in RGB mode.
1. Press the MENU button and then
2. Press the OK
3. Press the
F,
(A)
G button to
Each press of the
Clear
To exit the
button and then
F,
adjust
G button
use
the
changes
Soft
menu
use
display, repeatedly,
F,
D
,
G button to select the
E button to select APC item.
screen
the
menu.
condition
screen as
as
you want.
APC
FG
Clear
Contrast
80
Brightness
50
Color
50
Sharpness
50
MENU
prev.
move
FG select
shown below.
User
press the MENU button.
19
Function
Video Menu
Auto Color
Options
Temperature
Control
1. Press the MENU button and then
use
F,
G button to select the
menu.
FG
Normal
ACC
2. Press the OK
(A)
button and then
use
D
,
E button to select ACC item.
White
Peaking
Gamma
3. Press the
F,
G button to make
Each press of the
F,
G button
Normal
To exit the
appropriate adjustments.
changes the
screen as
Cool
menu
White
prev.
shown below.
Function
use
F,
G button to select the
menu.
FG
Normal
ACC
(A)
button and then
use
D
E button to select White
,
Peaking
item.
White
F,
G button to
adjust
the
screen
condition
as
Peaking
Gamma
MENU
3. Press the
FG select
press the MENU button.
1. Press the MENU button and then
2. Press the OK
FG
Normal
move
Warm
display, repeatedly,
Peaking
MENU
FG
10
prev.
FG
10
FG
Normal
move
FG select
you want.
The default value may changed based on input mode.
Adjust to higher value to see the bright picture and adjust to lower value to
see
the
quality picture.
To exit the
menu
display, repeatedly,
press the MENU button.
Gamma Function
1. Press the MENU button and then
use
F,
G button to select the
menu.
FG
Normal
ACC
2. Press the OK
(A)
button and then
use
D
,
E button to select Gamma item.
White
Gamma
MENU
3. Press the
F,
G button to
Each press of the
Normal
To exit the
20
F,
adjust
G button
the
changes the
Film
menu
screen
display, repeatedly,
condition
screen as
as
shown below.
Sports
press the MENU button.
you want.
Peaking
prev.
FG
10
FG
Normal
move
FG select
Function
Menu
Special
ENGLISH
Options
Selecting language
1. Press the MENU button and then
2. Press the OK
3. Press the
F,
button and then
(A)
use
use
G button to select the
F,
D
G button to select the
E button to select
,
Flip
This function
Language
item.
you want to use.
language from this point.
language
On-Screen-Display (OSD) is marked in the selected
To exit the menu display, repeatedly, press the MENU
*
menu.
Language
FG
ARC
FG
4:3
Flip
Horizontal
Flip
Vertical
FG
1
Set ID
MENU
English
prev.
move
FG select
button.
Horizontal Function
reverses
the
Use this function when
projected image horizontally.
projecting an image.
rear
1. Press the MENU button and then
use
F,
G button to select the
menu.
Language
(A)
button and then
use
D
,
E button to select
Flip
Horizontal
item.
Flip
Horizontal
Flip
Vertical
MENU
(A)
button to
see
reversed
English
Press OK to
Flip
FG
1
Set ID
3. Press the OK
FG
FG
4:3
ARC
2. Press the OK
prev.
move
AOK
image.
Each time you press the button, the image will be reversed.
To exit the menu display, repeatedly, press the MENU button..
Flip
Vertical Function
*
This function
*
When you hang the projector upside down from the ceiling
you will need to reverse the image vertically and horizontally.
reverses
the
projected image vertically.
,
1. Press the MENU button and then
use
F,
G button to select the
menu.
Language
2. Press the OK
(A)
button and then
use
D
,
E button to select
item.
Flip Vertical
Flip
Horizontal
Flip
Vertical
Set ID
MENU
3. Press the OK
(A)
button to
see
reversed
FG
English
FG
4:3
ARC
Press OK to
Flip
FG
1
prev.
move
AOK
image.
Each time you press the button, the image will be reversed.
To exit the menu display, repeatedly, press the MENU button.
21
Function
Menu
Special
Using
Options
ARC Function
1. Press the ARC button.
Each press of the button
You
can
*
display
as
below.
16:9
FG
4:3
FG
16:9
4:3
also
use
this function
Using Keystone
*
the
changes
by using
the MENU button.
function
Use this function when the screen is not at a right angle to the
projector and the image is a trapezoid shape.
Only use the Keystone function when you can't get the best
angle of projection, because it may cause a blazing fire of the
screen.
1. Press the KEYSTONE
+
or
KEYSTONE
2. Press the KEYSTONE
+
or
KEYSTONE
condition
as
Keystone
You
can
-
button.
button to
adjust
the
Keystone
screen
0
you want.
are
also
-
adjusted from
use
this function
-50 to +50.
by using
the MENU button.
Auto Source Function
*
Automatically
detects the
projector input signal.
1. Press the MENU button and then
2. Press the OK
3. Press the
To exit the
22
F,
(A)
button and then
use
use
G button to select On
menu
display, repeatedly,
F,
G button to select the
menu.
D E button to select Auto Source item.
or
Keystone
FG
Off
Blank
Image
FG
Blue
Lamp
Mode
FG
Normal mode
Lamp
Time
MENU
prev.
,
Off.
press the MENU button.
0
Auto Source
0Hr
move
FG select
Function
ENGLISH
Blank function
Using
*
This function may be effective if you need to
during presentations, meetings
or
get attention of the audience
briefings.
1. Press the BLANK button.
The
You
screen
can
turns off to
choose the
a
background
background
(Refer to 'Selecting
blank
color.
color.
image color')
2. Press any button to cancel the blank function.
Blank
Selecting
Image
color
1. Press the MENU button and then
2. Press the OK
(A)
button and then
use
use
F,
D
,
G button to select the
E button to select Blank
menu.
Image
item.
3. Press the
F,
color will be
Background
To exit the
Lamp
G button to select the color you want to
menu
changed to
display, repeatedly,
Image
FG
Blue
Lamp
Mode
FG
Normal
Lamp
Time
MENU
prev.
0Hr
move
FG select
point.
press the MENU button.
Mode Function
2. Press the OK
To exit the
0
FG
Off
Blank
use.
the selected Blank function color from this
1. Press the MENU button and then
3. Press the
Keystone
Auto Source
F,
(A)
button and then
use
use
F,
G button to select the
D E button to select Lamp Mode item.
display, repeatedly,
Keystone
0
,
G button to select Normal mode
menu
menu.
or
Silent mode.
press the MENU button.
Auto Source
FG
Off
Blank
Image
FG
Blue
Lamp
Mode
FG
Normal mode
Lamp
Time
MENU
prev.
0Hr
move
FG select
23
Function
Special
Menu
Checking lamp
Options
time
1. Press the MENU button and then
use
F,
G button to select the
The used lamp time is displayed.
When projector lamp is reaching the end of its life
menu.
Keystone
(over
2000
hours),
the
lamp
indicator will
be turned red.
The
lamp warning
LED illuminates red
continuously
in the
case
of excessive
lamp
time.
0
Auto Source
FG
Off
Blank
Image
FG
Blue
Lamp
Mode
FG
Normal mode
Lamp Time
MENU
Using
Still function
1. Press the STILL button.
*
You
can
freeze the
input image.
<Still
<Moving Image>
2. To exit
*
Pause, press any button
The STILL function would release
24
Image>
.
automatically
after about 10 minutes.
prev.
0Hr
move
FG
adjust
Function
Screen Menu
Auto
ENGLISH
Options
Function
Tracking
*This function
assures you of getting the best video quality by automatically
adjusting the difference of horizontal size and synchronization of the image.
*Auto Tracking function works in RGB input only.
1. Press the AUTO button.
Image positioning
and
synchronization
automatically adjusted.
are
Auto
2.
Adjust
Clock
or
Phase in
after
menu
operation
of Auto
Configure
Configure
if you want to get better picture quality in accordance with diverse RGB
input modes. In certain circumstances, you can't get the best picture
quality only with auto-correction.
You
can
also
this function
use
For best results,
perform
by using
the MENU button.
this function while
displaying
a
(Only
still
in RGB
mode)
image.
Clock / Phase Function
*
Clock Function
This function
image
*
to fit
the horizontal width of the
adjusts
on
the
screen
projected image
to
get the
size.
Phase Function
This function is for the detailed
adjustment of the clock function.
adjust [Clock], [Phase] in RGB mode only.
*It's available to
1. Press the MENU button and then
2. Press the OK
(A)
use
button and then
F,
use
Auto
G button to select the
D
,
menu.
E button to select Clock
or
Phase item.
3. Press the
To exit the
Configure
Clock
15
0
Vertical
0
MENU
G button to
F,
menu
adjust
display, repeatedly,
the
screen
0
Phase
Horizontal
prev.
move
FG
adjust
move
FG
adjust
condition.
press the MENU button.
Screen Position
*If the
image size does not fit the screen in accordance with the input
position of the image by selecting Horizontal / Vertical
position. (RGB mode)
source, set the
Auto
1. Press the MENU button and then
2. Press the OK
(A)
button and then
use
use
F,
D
,
G button to select the
E button to select Horizontal
Vertical item.
3. Press the
F,
or
the
screen
condition
as
0
Phase
15
Horizontal
0
Vertical
0
MENU
adjust
Configure
Clock
prev.
you want.
are adjusted from -50 to +50.
input mode, the adjustment range may be changed.
menu display, repeatedly, press the MENU button.
Horizontal,
Based
G button to
menu.
Vertical
the
on
To exit the
25
RS-232C
External Control Device
*
Connect the RS-232C
and control the
input jack to an external control
Projector's functions externally.
Setup
device
(such
as a
computer or a video control system)
SET ID
1. Press the MENU button and then
2. Press the OK
3. Press the
F,
(A)
button and then
G button to
adjust
use
use
F,
D
,
G button to select the
menu.
E button to select Set ID item.
Set ID to select the desired
projector
ID number.
Language
FG
ARC
FG
4:3
Flip
Horizontal
Flip
Vertical
The
adjustment range of Set ID is 1~99.
Only the projector with the specified ID number will operate from the
To exit the menu display, repeatedly, press the MENU button.
How to connect external control
?
Connect the serial
?
RS-232C cable is not
port of the PC
?
Use the RS232C cable to control the
supplied
<Fig.1,
RS-232 Interface Cable>
RXD
2
2
RXD
TXD
3
3
TXD
DTR
4
4
DTR
GND
5
5
GND
DSR
6
6
DSR
RTS
7
7
RTS
CTS
8
8
CTS
External
Projector
?
Baud Rate
:
Data
115200
Length :
Parity : none
?Stopbit:1bit
?
bps(UART)
8 bit
?
26
?
Flow Control
?
Communication code
: none
:
ASCII code
on
the
projector
back
projector externally (Refer to Fig.1).
96
5
1, 9 Pin No Connection
Communication Parameter
jack
projector.
Device
*
equipment
to the RS-232C
with the
remote control.
Setup
1
panel.
FG
1
Set ID
MENU
English
prev.
move
FG select
RS-232C
Command Reference List
Command1
Command2
k
a
01. Power
Select
Data
(Hexadecimal)
0~1
*
k
b
Ratio
k
c
04. Screen Mute
k
d
0~1
05. Contrast
k
g
0~64
06.
02.
Input
03.
Aspect
1~2
k
h
0~64
07. Color
k
i
0~64
08. Tint
k
j
0~64
09.
k
k
0~64
k
l
0~1
k
m
0~1
k
u
0~2
j
w
0~64
j
y
0~64
j
z
0~64
j
j
q
0~1
u
1
x
b
*
Brightness
Sharpness
10. OSD Select
11. Remote Control Lock /
12. Color
Key
Lock
Temperature
13. Red ADC
gain adjustment
14. Green ADC
15. Blue ADC
gain adjustment
gain adjustment
16. Low Power
17. Auto
configuration
18.
Select
*
Input
This data will be
explained
in this document in detail.
Communication Protocol
1. Transmission
[Command1][Command2][ ][Set ID][ ][Data][Cr]
*
*
*
[Command 1]
[Command 2]
[Set ID]
:
:
:
First command to control the
set.(k, j, x, ASCII code, 1 Character)
set..(ASCII code, 1 Character)
You can adjust the set ID to choose desired projector ID number in special menu.
99. When selecting Set ID '0', every connected projector
Adjustment range is 1
To transmit command data. Transmit 2 character when organized ASCII code.
Second command to control the
~
*
[DATA]
:
*
[Cr]
:
*
See
previous
page.
set is controlled.
Transmit 'FF' data to read status of command.
Return
Carriage
ASCII code '0x0D'
*
[]
:
ASCII code character
correspond
to
"Space
Bar" which is in order to
classify command,
set ID and Data.
2. OK Acknowledgement
[Command2] [ ] [Set ID] [ ] [OK] [Data] [x]
*
The
Projector transmits ACK (acknowledgement)
mode, it indicates present status data.
data read
3. Error
based
on
this format when
If the data is data write
receiving normal data. At this time, if the data is
mode, it returns the data of the PC computer.
Acknowledgement
[Command2] [ ] [Set ID] [ ] [NG] [Data] [x]
*
The
Projector
functions
Data
:
[1]
[2]
[3]
or
:
:
:
transmits ACK
communication
(acknowledgement)
based
on
this format when
receiving
abnormal data from non-viable
errors.
illegal code(This command is not supported.)
not support function(This function doesn't work.)
wait more time(Try again a few minute later.)
27
RS-232C
External control device setup
01. Power
03.
(Command2:a)
To control Power On/Off of the
Projector.
Aspect Ratio (Command2:c)
To
adjust
the
screen
format.
Transmission
Transmission
[k][a][][SetID][][Data][Cr]
Data
[k][c][][SetID][][Data][Cr]
Power Off
0
:
1
:PowerOn
Data 1
:
Normal
2
:
Wide
Ack
Ack
[a][][SetID][][OK][Data][x]
Data
[c][ ][SetID][ ][OK][Data][x]
Power Off
0
:
1
:PowerOn
Screen( 4:3)
Screen(16:9)
Data 1
:
Normal
2
:
Wide
Screen( 4:3)
Screen(16:9)
To show Power On/Off status.
Transmission
[k][a][ ][SetID][ ][FF][Cr]
Ack
04. Screen Mute
[a][][SetID][][OK][Data][x]
Data
*
To select
(Command2:d)
screen
mute on/off.
Power Off
0
:
1
:PowerOn
Transmission
In like manner, if other functions transmit '0xFF' data based
on this format, Acknowledgement data feed back presents
[k][d][][SetID][][Data][Cr]
Data
status about each function.
0
:
Screen Mute Off
1
:
Screen Mute On
(Picture On)
(Picture Off)
Ack
[d][][SetID][][OK][Data][x]
Data
02.
0
:
Screen Mute Off
1
:
Screen Mute On
(Picture On)
(Picture Off)
Input Select (Command2:b)
To select
input
source
for the Set.
Transmission
05. Contrast
[k][b][][SetID][][Data][Cr]
Data
2
:
Video
3
:
S-Video
4
:
Component
6
:
RGB-DTV
7
:
RGB-PC
8
:
DVI-DTV
9
:
DVI-PC
To
adjust
contrast.
Transmission
[k][g][][SetID][][Data][Cr]
Ack
Data
[b][][SetID][][OK][Data][x]
Data
(Command2:g)
screen
*
2
:
Video
3
:
S-Video
7
:
RGB-PC
9
:
DVI-PC
4
:
Component
Min:0~Max:64
Refer to 'Real data
1'.
mapping
Ack
[g][][SetID][][OK][Data][x]
*
The transmission data for
RGB-DTV(Data:6) input select is
changed to RGB-PC(Data:7) for the identical mode processing.
In like manner, the data of transmission for DVI-DTV(Data:8)
input select is changed to DVI-PC(Data:9).Therefore,if you send
command to select RGB-DTV
changed
28
or
DVI-DTV source,you will recieve
Data
*
Min:0~Max:64
Real data
mapping
1
*
Real data
mapping
data in the Ack message.
0
:
Step0
A
:
Step10
F
:
Step15
10
:
Step16
64
:
Step
100
0
32:
:Step-50
Step0
64:Step50
2
RS-232C
06.
Brightness (Command2:h)
To
adjust
screen
10. OSD Select
brightness.
Transmission
Transmission
[k][l][][SetID][][Data][Cr]
[k][h][ ][SetID][ ][Data][Cr]
Data
*
Data
Min:0~Max:64
Refer to 'Real data
mapping
1'.
0
:
OSD Select Mode Off
1
:
OSD Select Mode On
Ack
Ack
[l][][SetID][][OK][Data][x]
[h][ ][SetID][ ][OK][Data][x]
Data
To
Data
Min:0~Max:64
07. Color
adjust
the
screen
:
OSD Select Mode Off
1
:
OSD Select Mode On
color.
11. Remote Control
Lock/Key
(Command2:m)
[k][i][][SetID][][Data][Cr]
Data
0
(Command2:i)
Transmission
*
(Command2:l)
To select OSD On/Off.
To lock the front
Min:0~Max:64
Refer to 'Real data
mapping
projector
1'.
panel
Lock
controls
on
the
and remote control.
Transmission
Ack
[k][m][][SetID][][Data][Cr]
[i][][SetID][][OK][Data][x]
Data
Data
Min:0~Max:64
0
Lock Off
:
1:LockOn
Ack
[m][ ][SetID][ ][OK][Data][x]
Data
0
Lock Off
:
1:LockOn
08. Tint
To
(Command2:j)
adjust
the
screen
*
If
not
you're
using
the remote control,
use
this mode.
When main power is On/Off, external control lock is released.
tint.
Transmission
[k][j][][SetID][][Data][Cr]
Data
*
Red:0~Green:64
Refer to 'Real data
mapping2'.
Ack
[j][][SetID][][OK][Data][x]
Data
Red:0~Green:64
12. Color
Temperature (ACC) (Command2:u)
the color
Adjust
temperature.
Transmission
09.
Sharpness (Command2:k)
To
adjust
the
screen
sharpness.
Transmission
*
:
Normal
1
:
Cool
2:Warm
mapping
[u][ ][SetID][ ][OK][Data][x]
Data
Min:0~Max:64
Refer to 'Real data
0
Ack
[k][k][ ][SetID][ ][Data][Cr]
Data
[k][u][][SetID][][Data][Cr]
Data
0
:
Normal
1
:
Cool
2:Warm
1'.
Ack
[k][ ][SetID][ ][OK][Data][x]
Data
Min:0~Max:64
29
RS-232C
External control device setup
13. Red ADC
gain Adjustment (Color R)
(Command2:w)
Adjust
the Red
gain
of ADC
16. Low Power
part.(RGB)
Transmission
To reduce the power
*
consumption
of the
projector.
Transmission
[j][w][][SetID][][Data][Cr]
Data
(Command2:q)
Min:0~Max:64
Refer to 'Real data
1'.
mapping
[j][q][][SetID][][Data][Cr]
Data
0
Low Power Off
:
1:LowPowerOn
Ack
[q][][SetID][][OK][Data][x]
Data
Ack
Data
0
Low Power Off
:
1:LowPowerOn
[w][][SetID][][OK][Data][x]
Min:0~Max:64
14. Green ADC
gain Adjustment (Color G)
(Command2:y)
Adjust
the Green
gain
of ADC
17. Auto
part.(RGB)
Configure (Command2:u)
To
adjust picture position and
automatically. It works only in
minimize
image shaking
RGB mode.
Transmission
Transmission
[j][y][][SetID][][Data][Cr]
Data
*
[j][u][][SetID][][Data][Cr]
Min:0~Max:64
Refer to 'Real data
mapping
1'.
Data
1:Toset
Ack
[u][][SetID][][OK][Data][x]
Data
Ack
1:Toset
[y][ ][SetID][ ][OK][Data][x]
Data
Min:0~Max:64
15. Blue ADC
gain Adjustment (Color B)
(Command2:z)
Adjust
the Blue
gain
of ADC
part.(RGB)
18.
To select
Data
Min:0~Max:64
Refer to 'Real data
source
for the Set.
[x][b][][SetID][][Data][Cr]
[j][z][][SetID][][Data][Cr]
*
input
Transmission
Transmission
Data
Input Select (Command2:b)
mapping
20
:
Video
30
:
S-Video
40
:
Component
50
:
RGB-DTV
60
:
RGB-PC
70
:
DVI-DTV
80
:
DVI-PC
40
:
Component
1'.
Ack
[b][][SetID][][OK][Data][x]
Data
Ack
20
:
Video
30
:
S-Video
60
:
RGB-PC
80
:
DVI-PC
[z][ ][SetID][ ][OK][Data][x]
Data
Min:0~Max:64
*
The transmission data for
RGB-DTV(Data:50) input select is
RGB-PC(Data:60) for the identical mode processing.
In like manner, the data of transmission for DVI-DTV(Data:70)
input select is changed to DVI-PC(Data:80). Therefore,if you
changed
to
send command to select RGB-DTV
recieve
30
changed
or
DVI-DTV source, you will
data in the Ack message.
Information
Supported
*
The
following
table lists the
Format
640X350
70.090Hz
31.468kHz
640X350
85.080Hz
37.861kHz
640X400
70.090Hz
31.468kHz
640X400
85.080Hz
37.861kHz
720X400
70.082Hz
31.469kHz
720X400
85.039Hz
37.927kHz
640X480
59.940Hz
31.469kHz
640X480
72.800Hz
37.861kHz
640X480
75.00Hz
37.500kHz
640X480
85.008Hz
43.269kHz
800X600
56.250Hz
35.156kHz
800X600
60.317Hz
37.879kHz
800X600
72.188Hz
48.077kHz
800X600
75.00Hz
46.875kHz
800X600
85.061Hz
53.674kHz
1024X768
60.004Hz
48.363kHz
1024X768
70.069Hz
56.476kHz
1024X768
75.029Hz
60.023kHz
1024X768
84.99Hz
68.677kHz
1152X864
60.053Hz
54.348kHz
1152X864
70.01Hz
63.995kHz
1152X864
75.00Hz
67.500kHz
1280X960
60.00Hz
60.00kHz
1280X1024
60.020Hz
63.981kHz
SVGA
XGA
SXGA
*
*
Vertical
Freq.(Hz)
Horizontal
Freq. (kHz)
If the projector does not support the input signal, "Out of Range" message appears on the screen.
The projector supports DDC1/2B type as Plug & Play function. (Auto recognition of PC monitor)
The Synchronization input form for horizontal and vertical frequencies are Separate, Composite and SOG.
According to PC, the optimum vertical frequency may not be displayed up to the optimum frequency of set in
'Registration information (Display registration information)'. (ex, The optimum vertical frequency may be displayed
up to 75Hz or under in the resolution of 640X480 or 800X600.)
<DVD/DTV
Input>
Signal
Component-*1
NTSC(60Hz)
Cable
O
X
480p
O
O
720p
O
O
O
O
576i
O
X
576p
O
O
1080i
O
O
type
1- RCA to D-Sub
2-
RGB(DTV)-*2
480i
1080i
PAL(50Hz)
*
display formats supported by the projector.
VGAEGA
VGA
*
Display
Sources
PC98 / VGA text
*
Monitor
Computer
Adaptor
Cable
31
Information
Maintenance
*
The
projector needs little maintenance. You should keep the lens clean because any dirt or stains may appear
screen. If any parts need to be replaced, contact your dealer. When cleaning any part of the projector,
always turn the power off and unplug the projector first.
on
the
the lens
Cleaning
Clean the lens whenever you notice dirt
dry lint-free cloth.
To
remove
dirt
or
Cleaning
stains
the
on
Projector
projector case,
stubborn dirt
or
32
use
dust
the lens, moisten
To clean the
Do not
or
a
on
the surface of it.
Wipe
soft cloth with water and
a
the lens surface
neutral
gently
detergent
and
with
an
wipe the
air spray
or a
lens surface
soft,
gently.
Case
first unplug the power cable. To remove dirt or dust, wipe the casing with a soft, dry, lint-free cloth. To
stains, moisten a soft cloth with water and a neutral detergent and then wipe the casing.
alcohol, benzene, thinners or other chemical detergents as these can cause the casing to be warped or discolored.
remove
Information
Memo
33
Information
Memo
34
Information
Specifications
MODEL
BX220-JD
resolution
1024(Horizontal)
horizontal / vertical ratio
DLP
panel
screen
768(Vertical)pixel
4:3(horizontal:vertical)
size
0.55 inches
size
1.01~5.08m(40~200
inches)
remote control distance
12m
ratio
1:1.2
compatibility
NTSC/PAL/SECAM/NTSC4.43/PAL-M/PAL-N
zoom
Video
x
Power
AC 100
-
240V~50/60Hz,3A-1A, 260W
height(mm/inches)
100.7/3.9
breadth(mm/inches)
330/12.9
length(mm/inches)
220.1/8.7
Operating
Condition
Projector Lamp
temperature
In
In
operation
:
lamp
32~104°F(0°C~40°C)
: -4~140°F(-20°C~60°C)
AJ-LT91
storage and transit
humidity
In
lamp
power
operation : 0~80% relative humidity by dry hygrometer
operation : 0 90% relative humidity by dry hygrometer
Not in
model
consumption
200W
~
LAMP
Replacement
WARNING
:
Lamp
is
no user
Do not touch and open the
bottom enclosure. It could
shock due to
Only
service
cause
high temperature
personnel
can
replaceable part.
lamp replace
injury
and
cover
voltage.
replace lamp
after
minimum 3 min. from disconnect mains
plug
avoid
of
*
injury
cause
Applicable Lamp:
by high temperature
Manufactured
of
and electric
by
to
lamp.
USHIO Inc.,
type NSH200LG
35
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement