LG MDD112-A0U Owner's manual

LG MDD112-A0U Owner's manual
MDD112_72-A0U_ENG_MC
MDD112
(MDD112-A/D/X0U, MDS112V)
MDD72
(MDD72-A/D/X0U, MDS72V)
English
Mini Home Theater
Read the manual carefully before using the unit.
FRENCH
Mini Home Theater
Veuillez lire attentivement le présent manuel avant d'utiliser l'appareil.
P/N: MFL40996512
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO REDUCE THE RISK
OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
This lightning flash with arrowhead symbol within
an equilateral triangle is intended to alert the user
to the presence of uninsulated dangerous voltage
within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral triangle
is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
appliance.
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon a dedicated circuit;
That is, a single outlet circuit which powers only that appliance
and has no additional outlets or branch circuits. Check the
specification page of this owner's manual to be certain.
Do not overload wall outlets. Overloaded wall outlets, loose or
damaged wall outlets, extension cords, frayed power cords, or
damaged or cracked wire insulation are dangerous. Any of
these conditions could result in electric shock or fire.
Periodically examine the cord of your appliance, and if its
appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with
an exact replacement part by an authorized servicer.
Protect the power cord from physical or mechanical abuse,
such as being twisted, kinked, pinched, closed in a door, or
walked upon. Pay particular attention to plugs, wall outlets, and
the point where the cord exits the appliance.
To disconnect power from the mains, pull out the mains cord
plug. When installing the product, ensure that the plug is easily
accessible.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE.
CAUTION: Do not block any ventilation openings. Install in
accordance with the manufacturer's instructions.
Slots and openings in the cabinet are provided for ventilation
and to ensure reliable operation of the product and to protect it
from over heating.
The openings should be never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product
should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instruction have been adhered to.
CAUTION:
This Product employs a Laser System.
To ensure proper use of this product, please read this owner’s
manual carefully and retain for future reference, should the unit
require maintenance, contact an authorized service locationsee service procedure.
Use of controls, adjustments or the performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
To prevent direct exposure to laser beam, do not try to open
the enclosure. Visible laser radiation when open. DO NOT
STARE INTO BEAM.
CAUTION: The apparatus shall not be exposed to water,
dripping or splashing and that no objects filled with liquids,
such as vases, shall be placed on the apparatus.
2
POWER SAVE MODE
You can set up the unit into an economic power save
mode.
In power-on status, press and hold 1/[(POWER) button for about 3 seconds.
- Nothing is displayed in the display window when the
unit goes into the power save mode.
To cancel power save mode, press 1/[ (POWER).
Introduction
Installation
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
4
4
5
5
Operation
Operate using the front Panel . . . . . . . . . . . . . . . . . . 5
Operate using the Remote Control . . . . . . . . . . . . . . 6
Additional features. . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Caution
Indicates hazards likely to cause harm to
the unit itself or other material damage.
Note
Indicates special operating features of this
unit.
Indicates tips and hints to make the task
easier.
T ip
Playable Discs
Setup
Initial Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
DVD
(8 cm / 12 cm disc)
Playing an Audio CD or
MP3/WMA/JPEG/DivX file
Video CD (VCD)
(8 cm / 12 cm disc)
Playing an Audio CD or MP3/WMA file
Programmed Playback . . . . . . . . . . .
Viewing a JPEG file . . . . . . . . . . . . . .
Playing a DivX Movie file . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
12
12
12
13
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
14
14
15
16
16
16
17
Presetting the Radio Stations /
Listening
Presetting the radio stations . . . . . .
Listening to the radio . . . . . . . . . . .
RDS Operation - Optional . .
Timer function . . . . . . . . . . . . .
Setting the Clock . . . . . . . . . . . . . .
Timer Function . . . . . . . . . . . . . . . .
Operation with TAPE . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Reference
Language Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Area Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Specifications
Before use
About the
symbol display
“
” may appear on the TV screen during operation.
This icon means the function explained in this owner’s
manual is not available on that specific DVD video disc.
About the disc symbols for instructions
A section of which title has one of the following symbols
is applicable only to the disc represented by the symbol.
DVD DVD
VCD Video CDs
ACD Audio CDs
MP3 MP3 file
WMA WMA file
JPEG JPEG file
DivX DivX file
Audio CD
(8 cm / 12 cm disc)
In addition, this unit can play a DVD±R, DVD±RW,
SVCD, and CD-R or CD-RW that contains audio titles,
MP3, WMA, JPEG or DivX files.
Note
• Depending on the conditions of the recording equipment or the CD-R/RW (or DVD±R/RW) disc itself,
some CD-R/RW (or DVD±R/RW) discs cannot be
played on the unit.
• Do not attach any seal or label to either side (the
labeled side or the recorded side) of a disc.
• Do not use irregularly shaped CDs (e.g., heart-shaped
or octagonal). It may result in malfunctions.
Note on DVDs and Video CDs
Some playback operations of DVDs and Video CDs may
be intentionally fixed by software manufacturers. As this
unit plays DVDs and Video CDs according to disc content designed by the software manufacturer, some playback features of the unit may not be available or other
functions may be added.
Refer also to the instructions supplied with the DVDs
and Video CDs. Some DVDs made for business purposes may not be played on the unit.
Regional Code
This unit has a regional code printed on the rear of the
unit. This unit can play only DVD discs labelled as the
same as the rear of the unit or “ALL”.
Notes on Regional Codes
• Most DVD discs have a globe with one or more numbers in it clearly visible on the cover. This number
must match your unit’s regional code or the disc cannot play.
• If you try to play a DVD with a different regional code
from your player, the message “Check Regional
Code” appears on the TV screen.
3
ENGLISH
About the symbols for instructions
TV Connection . . . . . . . . . . . . .
Antenna Connection . . . . . . . . .
Speaker system connection. . . .
Optional Equipment Connection
Installation
Rear of TV
VIDEO
IN
FOR AM(MW) reception,connect the loop
antenna (aerial) to the
terminal marked AM
COMPONENT VIDEO /
PROGRESSIVE SCAN INPUT
Y
V
C
FM wire
antenna
(supplied)
To AUDIO IN
IN
VCR (or Auxiliary
Device.etc)
OUT
VIDEO
AUDIO (L)
AUDIO (R)
To AUDIO OUT
TV Connection
T ip
• Depending on your TV and other equipment you wish
to connect, there are various ways you could connect
the unit. Use one of the connections described below.
Component Video connection
Connect the COMPONENT VIDEO OUT (PROGRESSIVE SCAN) (Y PB PR) jacks from the unit to the corresponding jacks on the TV using a Y PB PR cable (C).
Progressive Scan connection
• Please refer to the manuals of your TV, VCR, Stereo
System or other devices as necessary to make the
best connections.
• If your television is a high-definition or “digital ready”
television, you may take advantage of this unit’s
progressive scan output for higher video resolution.
Caution
• If your TV does not accept the Progressive Scan format, the picture will appear scrambled if you try
Progressive Scan on the unit.
• Make sure the unit is connected directly to the TV.
Select the correct AV input on your TV.
• Do not connect your unit to TV via your VCR. The
DVD image could be distorted by the copy protection
system.
• If your television is a high-definition or “digital ready”
television, you may take advantage of the DVD/CD
unit’s progressive scan output for higher video resolution.
Connect the COMPONENT VIDEO OUT (PROGRESSIVE SCAN) (Y PB PR) jacks from the unit to the corresponding jacks on the TV using an optional Y PB PR
cable (C).
Antenna Connection
• If your TV does not accept your resolution setting,
abnormal picture appears on the screen. Please read
owner’s manual for TV then set the resolution that
your TV can accept.
Connect the supplied FM/AM antennas to listen to the
radio.
• Connect the AM loop antenna to the AM antenna connector.
• Connect the FM wire antenna to the FM antenna
connector.
Video connection
Note
Connect the VIDEO OUT jack from the unit to the
VIDEO IN jack on the TV using the video cable supplied
(V).
• To prevent noise pickup, keep the AM loop antenna
away from the unit and other component.
• Be sure to fully extend the FM wire antenna.
• After connecting the FM wire antenna, keep it as
horizontal as possible.
4
Speaker System Connection
Connect the speaker wires the speaker terminals.
Note
• Be sure to match the speaker wires to the appropriate terminal on the components, + to + and – to –. If the
cables are reversed, the sound will be distorted and will lack bass.
• If you use front speakers with low maximum input rating, adjust the volume carefully to avoid excessive output on
the speakers.
ENGLISH
Optional Equipment Connection
You can use VCR or other unit connected to the AUX connector.
Operation
Operation using the front Panel
6. USB
port
Connect the USB port of a USB Memory
(or MP3 player ,etc.) to the USB port on the front of the unit.
Removing the USB device from the unit
1.Choose a other functions except USB function in
order to remove the USB.
2.Remove the USB device from the unit
Note
Besides Basic Playback, if you want to operate other
functions, see the CD Playback section.
1.
DISPLAY WINDOW
( /[[)POWER button
• CD SYNCHRO RECORDING (CD SYNC.)/
DUBBING (DUBB.)/ (ST./MONO) button
• EQ button
/[ ] button
• REC/
• USB / DEMO button
DEMO : Press DEMO in power off state to demonstrate
the function in the display window.
To cancel it, press ( /[)POWER or DEMO
again. During demonstration in power-on status, you can cancel it by using the CLOCK,
TIMER buttons.
4. • XDSS/MP3 OPT.button
• XTS-PRO button
• FUNCTION SELECT buttons
(TUNER,TAPE,AUX, CD/DVD)
. bb/B
BB >),
• CD SKIP/SEARCH (.
. bb/B
BB >)
CD SCAN (.
REWIND/ FAST FORWARD - TAPE,
. bb/B
BB >),
TUNING (-/+)(.
• PRESET (-) button
B) button
• PRESET (+)/ FORWARD PLAY (B
• Volume control knob
2.
3.
5.
HEADPHONE Jack (PHONES):
3.5 mm
Don’t extract the USB device while operating.
Music files (MP3/WMA), image files (JPEG) and
Video files can be played.
This unit cannot use a USB HUB.
Recommended Memory Cards.
Compact Flash Card (CFC), Micro Drive (MD), Smart
Media Card (SMC), Memory Stick (MS), Secure Digital
Card (SD), Multimedia Card (MMC), Memory Stick Pro
(MS-Pro)
- Compatible with: FAT16, FAT32
- Only use the memory cards recommended.
Devices which require additional program installation when you have connected the unit to a computer are not supported.
In case of a USB HDD, make sure to connect an auxiliary power cord to the USB HDD for proper operation. Up to four primary partitions of a drive are supported. If there is an extension partition, it will not be
supported.
If the drive of USB device is two or more, a drive
folder is displayed on the screen. If you want to
move to the initial menu after you select a folder,
press RETURN.
Digital cameras and mobile phones are not supported.
Z PUSH EJECT position (TAPE 1)
Z PUSH EJECT position (TAPE 2)
• MIC VOLUME(MIC VOL.) knob : OPTIONAL
• MIC Jacks (MIC1/ MIC2): 3.5 mm : OPTIONAL
10. • OPEN/CLOSE ( Z OP./CL.) button
• DISC SKIP (D.SKIP) button
• SET/CD[[]/RDS-OPTIONAL
x) button
• STOP (x
11 • TIMER button
• CLOCK button
12. DISC DOOR
7
8.
9.
5
Operate using the Remote Control
POWER
5. SETUP
D.SKIP
22
1
TUNER/BAND
2
DVD
AUX
USB
SLEEP
21
3
DIMMER
20
4
v/V
V)
• PRESET -/+ (v
Press PRESET +/- repeatedly to select the preset
station you want.
Each time you press the button, the unit tunes in
one preset station at a time.
Preset radio stations in the unit’s memory first
(see “Presetting radio stations”)
• TUN.(-/+) (b/B)
For manual tuning, press TUN (-/+) repeatedly
For automatic tuning, press and hold TUN. (-/+) for
about two seconds on the front panel.
1 - TAPE - 2
SETUP
6. • Arrow buttons b/B/v/V (left/right/up/down)
(Selects an option in the menu)
DISPLAY
PRESET +
19
5
TUN. -
TUN. +
6
7. SELECT/ENTER
Acknowledges the menu selection.
8. MENU
Accesses the menu on a DVD disc.
SELECT
/ENTER
x)
9. • STOP (x
MENU
7
8
TITLE
18
STOP
PRESET PAUSE/STEP PLAY
ALL
9
Press X repeatedly to play Frame-by-Frame.
10
PROG./MEMO.
SCAN
REPEAT
SKIP
REPEAT A-B MARKER
DVD
17
SEARCH
MUTE
16
EQ
XTS Pro
SOUND
AUDIO
RETURN
ZOOM
S-TITLE
CLEAR
RDS
PTY
11
XDSS plus
VSM
15
14
ECHO VOL.
DivX
1.5 speed playback
DVD
VCD
MP3
WMA
ACD
You can quickly enjoy a movie and music.
The 1.5 speed allows you to watch the pictures and listen to the sound quicker than playing at a normal speed
on the disc.
1. Press the PLAY button during the normal playback.
The screen will appear at 1.5 speed with sound .
2. To return to normal PLAY, press PLAY.
13
1.
POWER(
2.
FUNCTION SELECT
(TUNER/BAND,DVD, AUX, USB)
3.
NUMERIC buttons (0-9)
Selects a service, program number directly or
selects numbered options in a menu.
)
TAPE FUNCTION
B)
• PLAY (B
•
•
•
•
6
VCD
B)
• PLAY (B
- To Play disc and file
MIC VOL.
12
4.
• PAUSE([[])/ STEP
During playback, press X to pause playback.
REWIND/ FAST FORWARD PLAY ( m / M)
TAPE 1-2 SELECT buttons (1-TAPE-2)
z/[])
RECORD/ RECORD PAUSE (z
x)
TAPE STOP (x
10. • PROG./MEMO.
Accesses or removes Program menu.
Enter a radio station’s frequency into the tuner.
• REPEAT
During playback, press REPEAT repeatedly to
select a desired repeat mode.
DVD Video discs: Chapter/Title/Off
Video CD, Audio CD, DivX/MP3/WMA discs:
Track/All/Off
• REPEAT A-B DVD VCD
During playback, press REPEAT A-B to select a
point A and a point B and repeats a sequence
from point A (Starting point) to point B (End point).
Press REPEAT A-B to exit.
Note
The A-B repeat function is available only in the current
title.
-You can select a desired sound mode by using EQ
button on the front panel or the remote control.
When you want to change a sound mode press the
EQ button repeatedly within 3 seconds.
Each time you press the button the setting changes
in the display window as shown below.
NORMAL → ARABIC → USER EQ → POP →
CLASSIC → ROCK → DRAMA → JAZZ →
NORMAL...
You can set the BASS, MIDDLE and TREBLE on
the USER EQ mode.
1.Select the USER EQ mode by using EQ
button.“USER EQ” will be displayed in the display
window.
2.Press the SET/CD[[ button on the front panel
when “USER EQ” is displayed in the display window.
“BASS 0” will be displayed in the display window
3.Select the BASS, MIDDLE or TREBLE you want
by pressing the PRESET (-/+) buttons on the front
panel.
4.Press the TUNING (-/+) buttons on the front panel
to set the sound level you want. (MIN, -4 ~ +4,
MAX steps)
5.Repeat the 3-4 steps as above.
• SUBTITLE (S-TITLE)
SUBTITLE DVD DivX
During playback, press S-TITLE repeatedly to
select a desired subtitle language.
• CLEAR
Removes a track number on the program menu or
a mark on the MARKER SEARCH menu.
12. ECHO VOL. ( / )
You can give an echo effect to the sound from the
microphones. Press ECHO VOL. ( / ) on the
remote control to increase the echo volume or
decrease it. (MIN,1 - 14, MAX steps)
13. MIC VOL. ( / )- OPTIONAL
Adjust the microphone volume by turning MIC volume knob. (MIN,1 - 14, MAX steps)
Note
• When not using the microphone, set the MIC volume
knob to minimum or turn off the MICs and remove the
microphone from the MIC Jacks.
• If the microphone is set too near the speaker, a howling sound may be produced. In this case, move the
microphone away from the speaker or decrease the
sound level by using the MIC volume control.
• If sound through the microphone is extremely loud, it
may be distorted. In this case, turn the MIC volume
control toward minimum.
6.When the sound level is completed, press the the
SET/CD[[ button on the front panel.
14. RDS,PTY - OPTIONAL
Views the various displays of the RDS options.
• XTS- Pro
This unique sound quality developed by our
technology creates the optimum sound for you to
play the perfect playback of the original sound and
to feel the living sound source.
Each time you press XTS Pro the setting changes
in the following order.
XTS -- P ON ↔ NORMAL
15. • XDSS plus/ MP3 OPT.
XDSS (Extreme Dynamic Sound System)
Press XDSS plus to reinforce treble, bass and the
surround effect. The “XDSS ON” or “NORMAL”
indicator lights.
Note : The XTS Pro function will not be operated
when a headphone has been connected
→ NORMAL → XDSS ON .
MP3 Optimizer
This function optimizes for compressed MP3 files.
It improves the bass sound to make sweet sound. Each
time you press “ MP3 OPT ”.
• SOUND
You can enjoy surround sound simply by selecting one of the pre-programmed sound fields
according to the program you want to listen to (2
ch. sound only).Press SOUND button repeatedly.
BYPASS → ON STAGE → STUDIO → CLUB →
HALL → THEATER 1 → CHURCH → BYPASS...
DVD/VCD/DivX/ACD
: XDSS ON ↔ NORMAL
MP3/WMA : XDSS ON → MP3 -- OPT ON
The setting changes in the following order.
XDSS ON → MP3 -- OPT ON → NORMAL
Note :Initial sound mode is BYPASS.
• AUDIO
AUDIO language: During playback, press AUDIO
repeatedly to hear a different audio language or
audio track. DVD DivX
(AUDIO channel): Press AUDIO repeatedly during
playback to hear a different audio channel
(Stereo., Left or Right). VCD
7
ENGLISH
11. • EQ (EQUALIZER Effect)
You can choose 7 fixed sound impressions and
adjust the BASS, MIDDLE and TREBLE.
• VSM (Virtual Sound Matrix)
Press VSM to set the VIRTUAL sound.
Source
2.1 ch.
5.1 ch
Display
VIRTUAL
VIRTUAL
Effect
3D STEREO
Virtual surround
3D STEREO
Realtime 3D positioned sound rendering technology
with stereo sources, optimized for stereo speakers.
Listeners may experience amazing virtual surround
effects with their own multimedia players.
Virtual surround
A patent pending downmix technology converts 5.1
channel to 2 channel sound having directional
information of audio.
• ZOOM
During playback or in the pause mode, press ZOOM to
enlarge the video image (3 steps).
You can move through the zoomed picture using
b/B/v/V buttons.
Note : Zoom may not work on some DVDs.
• RETURN (
)
Removes the setup menu.
16. • MARKER - SEARCH
To enter a Marker
You can start playback from up to nine memorized
points. To enter a marker, press MARKER at the
desired point on the disc. The Marker icon
appears on the TV screen briefly. Repeat to enter
up to nine markers.
To Recall or Clear a Marked Scene
1.During disc playback, press SEARCH. The marker
search menu appears on the screen.
2.Within 10 seconds, press b / B to select a marker
number that you want to recall or clear.
3.Press SELECT/ENTER and playback starts from
the marked scene. Or press CLEAR and the
marker number is erased from the list.
4.You can play any marker by inputting its number
on the marker search menu.
• MUTE(
)
Press MUTE to temporarily stop the sound the
( ) indicator flashes on display window. To cancel it ,press volume (-/+) or MUTE again.
. / >)
• SKIP (.
During playback, press SKIP (. or >) to go
to the next chapter/track or to return to the beginning of the current chapter/track.
Press SKIP . twice briefly to step back to the
previous chapter/track.
• SLOW
In the pause mode, press m or M to select
required speed.
DVD : t (1/2, 1/4, 1/8, 1/16) or T (1/2, 1/4, 1/8,
1/16) Video CD : T (1/2, 1/4, 1/8, 1/16)
8
m / M)
• SCAN (m
During playback, press SCAN (m or M)
repeatedly to select the required scan speed.
DVD : 5 steps
(BB, BBB, BBBB, BBBBB, BBBBBB),
bb, bbb, bbbb, bbbbb, bbbbbb)
(b
DivX disc, Video CD :4 steps
(BB, BBB, BBBB, BBBBB)
bb, bbb, bbbb, bbbbb)
(b
WMA/MP3, Audio CD
m (X2, X4, X8) or BB (X2, X4, X8)
17. VOLUME (-/+)
Adjusts speaker volume.
18. TITLE
(Use the TITLE button to display the title screen
included on DVD video discs.)
19. DISPLAY
1.Press DISPLAY to show various information about
the disc loaded on-screen.
The displayed items differ depending on the disc
type or playing status.
2.You can select an item by pressing v / V and
change or select the setting by pressing b / B.
Title (Track) –Current title (or track) number/total
number of titles (or tracks).
Chapter – Current chapter number/ total number
of chapters.
Time – Elapsed playing time.
Audio – Selected audio language or channel.
Subtitle – Selected subtitle.
Angle – Selected angle/ total number of angles.
Sound – Selected sound mode.
Note : If a button is not pressed for a few seconds,
the on-screen display disappears.
System Select
This function dims the LED (Light-emitting diode) of
front panel by half in power-on status.
Press DIMMER once. The LED (Light-emitting
diode) of front panel is turned off and the display
window will be darken by half.To cancel it, press
DIMMER again.
21. SLEEP
You must select an appropriate system mode for your
TV system. If NO DISC appears in the display window,
press and hold PAUSE/STEP remote control for more
than 5 seconds to be able to select a system
(PAL, NTSC or AUTO).
- When the selected system is not compatible with the
system of your TV, normal colour picture may not be
displayed.
You can set the unit to turn off automatically at a
specified time .
NTSC: Select when the unit is connected with
NTSC-TV.
1. Press SLEEP to set the desired sleep time.
The SLEEP indicator and the sleep time appears
in the display window.
PAL:
2. Each time you press SLEEP the setting changes
in the following order.
→80→
→70 → 60→
→
SLEEP180 →150 → 120 →90→
50 → 40 → 30 → 20 →10 → OFF (No display)
→SLEEP 180...
Note : You can check the remaining time before
the unit turn off
Press SLEEP. The remaining time
appears in the display window.
Select when the unit is connected with PAL-TV.
AUTO: Select when the unit is connected with Multi
system TV.
Camera Angle DVD
If the disc contains scenes recorded at different camera
angles, you can change to a different camera angle
during playback.
1.Press DISPLAY and then press the v / V to select a
angle.
The number of the current angle appears in the display
window.
2. Select a desired angle pressing the b / B buttons.
22. DISC SKIP (D.SKIP)
This function is used when you want to change the
current during playing disc.
Additional features
Time Search DVD
VCD
DivX
To start playing at any chosen time on the disc:
1. Press DISPLAY during playback.
2. Press v / V to select the time clock icon and
“--:--:--” appears.
3. Input the required start time in hours, minutes, and
seconds from left to right. If you enter the wrong
numbers, press CLEAR to remove the numbers you
entered. Then input the correct numbers.
4. Press SELECT/ENTER to confirm. Playback starts
from the selected time.
Screen Saver
The screen saver appears when you leave the unit in
Stop mode for about five minutes.
Last Scene Memory DVD
This unit memorizes the last scene from the last disc
that is viewed. The last scene remains in the
memory even if you remove the disc from the unit or
switch off the unit. If you load a disc that has the scene
memorized, the scene is automatically recalled.
Note
This unit does not memorize the scene of a disc if you
switch off the unit before commencing to play the disc.
9
ENGLISH
20. DIMMER
Setup
Initial Settings
By using the Setup menu, you can make various adjustments to items such as picture and sound. You can also
set a language for the subtitles and the Setup menu,
among other things. For details on each Setup menu
item, read the page 10 to 11
Original – Refers to the original language in which the
disc was recorded.
Other – To select another language, press numeric buttons and then SELECT/ENTER to enter the corresponding 4-digit number according to the language code list on the page 18. If you enter the
wrong language code, press CLEAR.
DISPLAY
a
TV Aspect
b
4:3 – Select when a standard 4:3 TV is connected.
c
16:9 – Select when a 16:9 wide TV is connected.
d
Display Mode
e
The display Mode setting works only when the TV
Aspect mode is set to “4:3”.
a LANGUAGE - OSD / Disc Audio / Subtitle / Menu
b DISPLAY - TV Aspect / Display Mode /
Progressive Scan
c AUDIO - Dynamic Range Control (DRC) / Vocal
d LOCK (Parental Control) - Rating / Password /
Area Code
e OTHERS - PBC / DivX(R) Registration
To display and exit the Menu:
Press SETUP to display the menu. A second press of
SETUP will take you back to initial screen.
To go to the next level:
Press B on the Remote Control.
To go back to the previous level:
Press b on the Remote Control.
General Operation
1. Press SETUP. The Setup menu appears.
2. Use v / V to select the desired option then press B
to move to the second level. The screen shows the
current setting for the selected item, as well as alternate setting(s).
3. Use v / V to select the second desired option and
then press B to move to the third level.
4. Use v / V to select the desired setting then press
SELECT/ENTER to confirm your selection. Some
items require additional steps.
5. Press SETUP or PLAY to exit the Setup menu.
LANGUAGE
OSD
Select a language for the Setup menu and the onscreen display.
Disc Audio / Subtitle / Menu
Select the language you prefer for the audio track (disc
audio), subtitles, and the disc menu.
10
Letterbox – Displays a wide picture with bands on the
upper and lower portions of the screen.
Panscan – Automatically displays the wide picture on
the entire screen and cuts off the portions that do not fit.
Progressive Scan
Progressive Scan Video provides the high quality pictures with less flickering. If you are using the
Component Video jacks for connection to a TV or monitor that is compatible with a progressive scan signal, set
[Progressive Scan] to [On]. Press SELECT/ENTER to
confirm your selection. The confirm menu will appear.
To Turn ON progressive scan:
Connect component out of the unit to the input of your
monitor/television, set your television or monitor to
Component Input.
1. Select “Progressive Scan” on the DISPLAY menu
then press B
2. Select “On” using the v / Vbuttons.
3. Pressing SELECT/ENTER will set the player to
Progressive scan mode.
Caution
Once the setting for progressive scan output is entered,
an image will only be visible on a progressive scan compatible TV or monitor. If you set Progressive Scan to on
in error, you must reset the unit. First, remove the disc in
the unit. Next, press STOP on the remote control ( x )
and hold it for five seconds before releasing it. The
video output will be restored to the standard setting, and
a picture will once again be visible on a conventional
analog TV or monitor.
Each DVD disc has a variety of audio output options.
Set the unit’s AUDIO options according to the type of
audio system you use.
Dynamic Range Control (DRC)
With the DVD*1 format, you can hear a program’s
soundtrack in the most accurate and realistic presentation, thanks to digital audio technology. However, you
may wish to compress the dynamic range of the audio
output (the difference between the loudest sounds and
the quietest ones). Then, you may listen to a movie at a
lower volume without losing clarity of sound. Set DRC to
On for this effect.
*1: Dolby Digital only
Vocal
Set Vocal to On only when a multi-channel karaoke
DVD is playing. The karaoke channels on the disc will
mix into normal stereo sound.
LOCK (Parental Control)
Rating
Blocks playback of rated DVDs based on their contents.
Not all discs are rated.
1. Select “Rating” on the LOCK menu then
press B.
2. To access the LOCK options, you must input the
password you have created. If you have not yet
entered password, you are prompted to do so.
Input a password and press SELECT/ENTER. Enter
it again and press SELECT/ENTER to verify. If you
make a mistake before pressing SELECT/ENTER,
press CLEAR.
3. Select a rating from 1 to 8 using the v / V buttons.
Rating 1-8: Rating one (1) has the most restrictions
and rating eight (8) is the least restrictive.
Unlock: If you select unlock, parental control is not
active and the disc plays in full.
4. Press SELECT/ENTER to confirm your rating selection, then press SETUP to exit the menu.
Password
You can enter or change password.
1. Select Password on the LOCK menu and then press B.
2. Follow the step 2 as shown above (Rating).
To change the password, press SELECT/ENTER
when the “Change” option is highlighted. Input a
password and press SELECT/ENTER. Enter it again
and press SELECT/ENTER to verify.
3. Press SETUP to exit the menu.
If you forget your password
If you forget your password, you can clear it using the
following steps:
1. Press SETUP to display the Setup menu.
2. Input the 6-digit number “210499” and press
SELECT/ENTER. The password is cleared.
Area Code
Enter the code of the area whose standards were used
to rate the DVD video disc, based on the list on page .
1. Select “Area Code” on the LOCK menu then
press B.
2. Follow step 2 as shown in rating section.
3. Select the first character using v / V buttons.
4. Press B and select the second character using
v / V buttons.
5. Press SELECT/ENTER to confirm your Area code
selection.
OTHERS
PBC
Set Playback Control (PBC) to On or Off.
On: Video CDs with PBC are played according to
the PBC.
Off: Video CDs with PBC are played in the same way
as Audio CDs.
DivX(R) Registration
We provide you the DivX® VOD (Video On Demand)
registration code that allows you to rent and purchase
videos based on the DivX® VOD service. For more
information, visit www.divx.com/vod.
1. Select “DivX(R) Registration” option and then press
B.
2. Press SELECT/ENTER while “Select” is selected
and the registration code will appear.
Use the registration code to purchase or rent the
videos from DivX® VOD service at
www.divx.com/vod. Follow the instructions and
download the video onto a disc for playback on this
unit.
3. Press SELECT/ENTER to exit.
Note
All the downloaded videos from DivX® VOD can only be
played back on this unit.
Semi Karaoke
When a chapter/ title / track is fully finished, this function
shows the score in the screen with a fanfare sound.
Semi Karaoke on :
- Turn the “Semi Karaoke” function on.
When you finished singing a score will appear on the
screen.
Semi Karaoke off :
- Turn the “Semi Karaoke” function off.
Fanfare and score do not appears on the screen
Available discs for the Semi Karaoke function:
• DVD discs
• DVD Karaoke discs
• VCD discs with more than 2 tracks
Note
• This function operate on the DVD/CD mode.
• The Semi Karaoke function is available only when a
microphone is connected.
• Watching movies, “off ” the Semi Karaoke or enjoy it
without connecting the MIC at the SETUP menu if the
fanfare or score appears during changing a chapter.
11
ENGLISH
AUDIO
Playing an Audio CD or MP3/WMA/JPEG/DivX file
Playing an Audio CD or MP3/WMA
file
2. Press REPEAT to select a desired repeat mode.
• TRACK: repeats the current track
• ALL: repeats all the tracks on programmed list.
This unit can play Audio CDs or MP3/WMA files.
MP3/ WMA/ Audio CD
Once you insert a cd with MP3/WMA files or Audio, a
menu appears on the TV screen.
Press v / V to select a track/file and then press PLAY
or SELECT/ENTER, and playback starts. You can use
variable playback functions. Refer to the page 6 -9.
ID3 TAG
When playing a file containing information such as track
titles, you can see the information by pressing DISPLAY
repeatedly. The information [ Folder and file name,
Song, Artist, Album, Genre, Comment, Time information
] of the MP3/WMA file will be shown in the display window and TV screen.
• Off(No display): does not play repeatedly.
Erasing a Track from “Program” List
1. Use v V to select the track that you wish to erase
from the Program list.
2. Press CLEAR. Alternatively, select “
(Delete)”
icon then press SELECT/ENTER to place the selected track on the Program list. Repeat to erase additional tracks on the list.
Erasing the Complete Program List
Use v / V to select “
SELECT/ENTER.
(Del all)” and then press
Note
To move next or previous files, press the SKIP
(. / >) button.
The programs are also cleared when the disc is
removed.
T ip
Viewing a JPEG file
Press MENU to move to the next page.
On a CD with MP3/WMA and JPEG, you can switch
MP3/WMA and JPEG. Press TITLE, and MUSIC or
PHOTO top of the menu is highlighted.
Programmed Playback
The program function enables you to store your favorite
tracks from any disc in the unit memory. A program can
contain 300 tracks.
1. Insert a disc.
Audio CD and MP3/WMA Discs:
2. Select a track on the “List”, and then press PROG.
or select “
(Add)” icon and then press
SELECT/ENTER to place the selected track on the
“Program” list. Repeat to place additional tracks on
the list.
Note
You can add all tracks in the disc. Select “
then press SELECT/ENTER.
This unit can play discs with JPEG files.
Before playing JPEG recordings, read the notes on
JPEG Recordings on the right.
1. Insert a disc and close the tray.
The PHOTO menu appears on the TV screen.
2. Press v / V to select a folder, and then press
SELECT/ENTER.
A list of files in the folder appears.
If you are in a file list and want to return to the
previous Folder list, use the v / V buttons on the
Remote to highlight
and press
SELECT/ENTER.
3. If you want to view a particular file, press v / V to
highlight a file and press SELECT/ENTER or PLAY.
While viewing a file, you can press STOP to move to
the previous menu (JPEG menu).
T ip
(Add All)” icon
There are four Slide Speed options
:
> (Slow), >> (Normal), >>> (Fast) and II (off).
Use v /V /b /B to highlight the Speed. Then, use b /
B to select the option you want to use and then press
SELECT/ENTER.
If you set Speed option to Off, the slide is not active.
3. Select the track you want to start playing on the
“Program” list. Press MENU to move to the next page.
4. Press PLAY or SELECT/ENTER to start. Playback
begins in the order in which you programmed the
tracks. Playback stops after all of the tracks on the
“Program” list have played once.
5. To resume normal playback from programmed playback, select a track of AUDIO CD (or MP3/WMA) list
and then press PLAY.
Repeat Programmed Tracks
1. Press REPEAT when playing a disc. The repeat icon
appears.
12
Slide Show
Use v V b B to highlight the
press ENTER.
(Slide Show) then
Still Picture
1. Press PAUSE/STEP during the slide show.
The unit will now go into the PAUSE mode.
2. To return to the slide show, press PLAY or press
PAUSE/STEP again.
Press (. or >) once during viewing a picture to
advance to the next or previous file.
Rotating the picture
Press v /V /b /B during showing a picture to rotate the
picture clockwise or counter-clockwise.
3. If you want to view a particular file, press
v / V to highlight a file and press SELECT/ENTER
or PLAY.
4. Press STOP to exit.
T ip
Zoom
Each time ZOOM is pressed the setting changes in the
following order.
Zoom on y Zoom off
Press MENU to move to the next page.
On a CD with MP3/WMA, JPEG and MOVIE file, you
can switch MUSIC, PHOTO and MOVIE menu. Press
TITLE and MUSIC, PHOTO and MOVIE word on top
of the menu is highlighted.
Note
Press v V b B to enlarge the video image.
• Be sure to select “SUBTITLE ON” mode by pressing
the subtitle file every time before playing a DivX file .
Press v V b B to reduce the video image.
• When the subtile has more than two languages in the
file, original subtile is only available.
Playing a DivX Movie file
Using this unit you can play DivX disc.
• You can not adjust sound mode and VIRTUAL sound
during the DivX file playing.
1. Insert a disc and close the tray. The MOVIE menu
appears on the TV screen.
Notice for displaying the Divx subtitle
2. Press v / V to select a folder and then press
SELECT/ENTER. A list of files in the folder appears.
If you are in a file list and want to return to the
Folder list, use the v / V buttons on the remote to
highlight
and press SELECT/ENTER.
If the subtitle does not display properly during playback,
press and hold S-TITLE for about 3 seconds then press STITLE to select another language code until the subtitle is
displayed properly .
MP3 / WMA disc compatibility with this player is
limited as follows:
• Some discs may not operate due to a different
recording format or the condition of disc.
• Sampling frequency: within 32 - 48 kHz (MP3),
within 24 - 48kHz (WMA)
• File extensions: “.jpg”
• Bit rate: within 32 - 320kbps (MP3), 40 - 192kbps
(WMA)
• File extensions: “.mp3” / “.wma”
DivX disc compatibility with this player is limited as
follows:
• Available resolution: within 800x600 (W x H) pixels
• CD-ROM file format: ISO9660
• The file name of the DivX subtitle is available by 45
characters.
• We recommend that you use Easy-CD Creator, which
creates an ISO 9660 file system.
• If there is impossible code to express in the DivX file,
it may be displayed as " _ " mark on the display.
• The total number of characters for file name: maximum 8 characters (excluding file extensions like
mp3/wma)
• Frame rate : less than 30 fps
• They should not contain special letters such as / ? * :
“ < > l etc.
• The total number of files on the disc should be less
than 999.
Customers should note that permission is required
in order to download MP3 / WMA files and music
from the Internet. Our company has no right to
grant such permission. Permission should always
be sought from the copyright owner.
JPEG disc compatibility with this player is limited
as follows:
• Image file size: less than 2M pixels(2760 x 2048 pixels) recommended (It may take longer to display a
lager than 2M pixel size files)
• Maximum files : Under 999.
• If the video and audio structure of recorded files
is not interleaved, either video or audio is outputted.
• Playable DivX file: ".avi ", ".mpg ", ".mpeg ", ".divx"
• Playable Subtitle format: SubRip(*.srt/*.txt),
SAMI(*.smi), SubStation Alpha(*.ssa/*.txt),
MicroDVD(*.sub/*.txt), SubViewer 2.0(*.sub/*.txt),
VobSub(*.sub)
• Playable Codec format: DIVX3.xx ", "DIVX4.xx ",
"DIVX5.xx ", "MP43 ", "3IVX ".
• Playable Audio format: "AC3 ", "PCM ", "MP3 ",
"WMA ".
• Sampling frequency: within 32 - 48 kHz (MP3),
within 24 - 48kHz (WMA)
• Bit rate: within 32 - 320kbps (MP3), 40 - 192kbps
(WMA)
13
ENGLISH
Moving to another File
Presetting the Radio Stations / Listening
Presetting the radio stations
Listening to the radio
You can preset 50 stations for FM and AM.
Before tuning, make sure that you have turned the volume down to the minimum level.
1
Press TUNER/BAND on the remote control to show
either FM or AM in the display window. Or Press
TUNER on the front panel.
The last received station is tuned in.
2
Press v /Von the remote control repeatedly to
select the preset station you want.
Each time you press this button, the unit tunes in
the next preset station.
3
Adjust the volume by turning VOLUME
CONTROL KNOB (or pressing VOLUME (-/+) on
the remote control) repeatedly.
1
2
Press TUNER/BAND on the remote control to show
either FM or AM in the display window. Or Press
TUNER on the front panel.
Every time you press this button, AM and FM
changes alternately.
Select a station you want by pressing
TUNING (-/+) on the front panel or b / B on the
remote control.
Note
• Automatic Tuning
Press TUNING (-/+) or b / B for more than 0.5
second.
- Scanning stops when the unit tunes in a station.
• Manual Tuning
Press TUNING (-/+) or b / B briefly and repeatedly.
3
Press PROG./MEMO. on the remote control.
A preset number will flash in the display window.
4.
Press v /V on the remote control to select the preset number you want.
5
Press PROG./MEMO. again.
The station is stored.
6
Repeat steps 1 (or 2) to 5 to store other stations.
To clear all memorized stations
Press and hold PROG./MEMO. on the remote control
for about two seconds, “ERASE ALL” appears in the display window and then press PROG./MEMO. on the
remote control, the stations are cleared.
For your reference
If all stations have already been entered, “FULL”
message will appear in the display window for a
moment and then a preset number will flash.
To change the preset number, follow the steps 4-5 .
To recall preset numbers
Press and hold v /V on the remote control until the
desired preset number appears or press the button
repeatedly.
14
To listen to non-preset radio stations
• For manual tuning, see “Manual Tuning”.
• For automatic tuning, see “Automatic Tuning”.
To select a preset radio station directly
You can use the number buttons on the remote control
to select a preset radio station directly.
For example, to listen to preset station 4, press 4 on the
remote control. To listen to preset station 19, press 1
then 9 (within 3 seconds).
To turn the radio off
Press POWER to turn off the unit or select another
function mode
(DVD/CD, TAPE, AUX or USB) .
For your reference
• If a FM program is noisy ;
Press ST./MONO repeatedly so that that “STEREO”
disappears in the display window. There will be no
stereo effect, but the reception will improve. Press
ST./MONO again to restore the stereo effect.
• To improve reception;
Reposition the supplied antennas.
RDS Operation - Optional
RDS TUNING
When a FM station is tuned in and it contains RDS
data, the unit will automatically display the station’s call
sign and the RDS indicator will light in the Display
Window as well as indicators for the RDS services programme (PS), programme type recognition (PTY),
Radio text (RT) and Clock Time (CT) if transmitted by
the station.
RDS DISPLAY OPTIONS
The RDS system is capable of transmitting a wide variety of information in addition to the initial call sign that
appears when a station is first tuned. In normal RDS
operation the display will indicate the station name,
broadcast network or call letters. Pressing RDS on the
remote control enables you to cycle through the various
data types in the sequence:
(PS ↔ FREQUENCY ↔ PTY ↔ RT ↔ CT)
PS (Programme Service name)- The name of the
channel is shown in the Display Window.
PTY (Programme type recognition)- The name of
the programme type is shown in the Display Window.
RT (Radiotext)- A “text” message contains special
information from the broadcast station. Note that this
message may scroll across the display to permit
message.
CT (Time controlled by the channel)- Enables the
unit to receive the actual time and show it in the
Display Window.
Note
Some RDS stations may not choose to include some of
these additional features. If the data required for the
selected mode is not being transmitted, the Display
Window will show a PTY NONE, RT NONE, CT NONE,
or PS NONE message.
Programme Search (PTY)
A major benefit of RDS is its ability to encode broadcasts with Programme Type (PTY) codes that indicate
the type of material being broadcast. The following list
shows the abbreviations used to indicate each PTY
along with an explanation of the PTY.
NEWS
AFFAIRS
INFO
SPORT
EDUCATE
DRAMA
CULTURE
SCIENCE
VARIED
POP M
ROCK M
EASY M
LIGHT M
CLASSICS
OTHER M
WEATHER
FINANCE
CHILDREN
SOCIAL
RELIGION
PHONE IN
TRAVEL
LEISURE
JAZZ
COUNTRY
NATION M
OLDIES
FOLK M
DOCUMENT
TEST
ALARM !
ENGLISH
This unit is equipped with RDS (Radio Data System),
which brings a wide range of information to FM radio.
RDS, now being used in many countries, is a system for
transmitting station call signs or network information, a
description of station programme type text message
about the station or specifics of musical selection and
the correct time.
News
Current Affairs
Information
Sports
Educational
Drama
Culture
Science
Varied Speech Programme
Popular Music
Rock Music
Easy Listening Music
Light Music
Classical Music
Other Music
Weather Information
Financial Programmes
Children’s Programmes
Social Affairs Programmes
Religious Broadcasts
Phone-In Programmes
Travel and Touring
Leisure and Hobby
Jazz Music
Country Music
National Music
Oldies Music
Folk Music
Documentary Programmes
Station Alarm Test Message
Emergency Broadcast Information
You may search for a specific Programme Type (PTY)
by following these steps:
1. Press TUNER to select the FM mode.
2. Press PTY on the remote control, the display will
show the last PTY in use.
3. Press PTY repeatedly to select a desired PTY.
4. When the PTY is selected, press TUN.(-/+).The unit
will go into an automatic search mode. When a station is
tuned, the search will stop.
15
Timer function
Setting the Clock
3)
Select the previous memorized preset
BB > on the
number by pressing . bb/B
front panel and press SET/CD[[ .
‘ON TIME’ indicator appears for about 0.5
seconds in the display window and then
disappears.
1
Press CLOCK.
(If the clock requires setting, press and hold CLOCK
for more than 2 seconds.)
- The hours display begins to blink.
2
Select a 24 hour cycle or 12 hour cycle by
BB > on the front panel.
pressing . bb/B
3
Press SET/CD[[ to confirm the selected hour
cycle.
4
BB > on the front panel to set
Use . bb/B
the correct hours.
5
5 Press SET/CD[[.
BB > on the front panel to set
6. Use . bb/B
the correct minutes.
6
Press SET/CD[[.
7
Set the minute to switch on by pressing
. bb/B
BB > on the front panel.
7
8
Press SET/CD[[ to confirm the turn on
minutes time.
‘OFF TIME’ indicator appears for about 0.5
seconds in the display window and then
disappears.
9
Set the hour to switch off by pressing
. bb/B
BB > on the front panel.
10
11
Press SET/CD[[.
Set the minute to switch off by pressing
. bb/B
BB > on the front panel.
12
13
Press SET/CD[[.
Adjust the volume level by pressing
. bb/B
BB > on the front panel.
14
Press SET/CD[[.
“ ” appears in the display window and the timer
setting has been completed.
15
Turn the system off.
The selected timer functions are automatically
switched on and off at the preset times.
Press SET/CD[[ and the correct time is shown in
b.
‘ON TIME’ indicator appears for about 0.5
seconds in the display window and then
disappears.
the display window.
Timer Function
With the TIMER function you can have the radio reception, CD play, USB play and TAPE play turned on and off
at the desired time.
1
Press CLOCK to check the current time.
For your reference
If you don’t set clock, timer function doesn’t work.
2
Press TIMER to enter the timer setting mode.
“TUNERtDVD/CD tUSB tTAPE” flash in the
display window in turn.
For your reference
• If you want to correct the previous memorized TIMER
setting, press and hold the TIMER button more than 2
seconds.
• If you want to check the previous memorized TIMER
setting,press TIMER button briefly.
- The previous memorized timer setting for on Time and
“ ” indicator appears in the display window.
3
Press SET/CD[[ when the desired function
flashes.
4
a. 1) When you select TUNER function,
‘PLAY’ and ‘REC’ indicator flash in
the display window alternately for
about 3 seconds.
‘PLAY’ indicator : TUNER play only
‘REC’ indicator : TUNER play and recording
2) Press SET/CD[[ when the desired
function flashes.
16
When you select DVD/ CD, USB or TAPE
function,
Set the hour to switch on by pressing
. bb/B
BB > on the front panel.
To cancel or check the timer
Each time the TIMER button is pressed you can select
the timer set or cancel. You can also check the timer
setting status.
To activate or check the timer, press the TIMER
button repeatedly so that “ ” appears in the display window.
To cancel the TIMER, press the TIMER button
repeatedly so that “ ” disappears from the display
window.
Note
• If you insert the DVD,VCD or DivX except audio
CD/MP3/WMA on the unit, the timer function will be
operated to the TUNER.
• This is not supported in the multi card reader.
Basic Playback
Basic Setting
1
1
2
3
Press TAPE1-2 (or TAPE) to select tape function.
(“NO TAPE ” appears in the display window.)
Open cassette TAPE1-2 by pushing to the
PUSH EJECT position.
Insert one or two cassettes with the tape side
to the bottom and then close the TAPE 1
(and/or 2) door.
2
Select a function you want to record except
tape function.
Open the cassette deck TAPE 2 and insert a
blank cassette into the cassette compartment.
Set the recording direction
Recording from Radio, CD or Auxiliary source
To Stop Play
Press REC/[] on the front panel or z/[] on the
remote control.
“REC” flashes and holds the cassette in pause
mode.
Press REC/[] on the front panel or z/[] on the
remote control.
The recording begins.
Press STOP (x) on the front panel or TAPE
STOP(x) on the remote control during playback.
Press REC/[] or z/[].
4
1
Press B.
AUTO STOP DECK (TAPE 1/2)
After auto stop deck plays front side of cassette, the
unit stops automatically.
2
To pause the recording
To Stop the recording
To Play Rewind or Fast Forward
BB > on the front panel or
After press . bb/B
bb / BB on the remote control during playback,
press B at the tape position you want.
Dubbing
This function shows how to record from tape to tape.
1 Press TAPE1-2 (or TAPE).
• Cassette TAPE 1- Insert the playback tape to dub.
• Cassette TAPE 2- Insert a blank tape to copy on.
2 Press DUBB.
DUBBING - Normal speed copying
To stop recording, press STOP (x).
Press STOP(x)
CD to Tape Synchronized Recording
The CD synchro recording function dubs a complete
CD and programmed titles automatically into a cassette.
1
Press DVD button on the remote control.
2
Press CD SYNC. in stop mode.
“REC” flashes and “CD SYNC” displays in the
display window.
3
The synchronized recording is started
automatically after about 7 seconds.
Note
• If you wish to record from the desired track, select
the desired track with . bb/BB > or ./>
before commencing CD synchro recording.
• You cannot change any mode during recording.
17
ENGLISH
Operation with TAPE
Reference
Language Codes
Use this list to input your desired language for the following initial settings: Disc Audio, Disc Subtitle, Disc Menu.
Language
Abkhazian
Afar
Afrikaans
Albanian
Ameharic
Arabic
Armenian
Assamese
Aymara
Azerbaijani
Bashkir
Basque
Bengali; Bangla
Bhutani
Bihari
Breton
Bulgarian
Burmese
Byelorussian
Cambodian
Catalan
Chinese
Corsican
Croatian
Czech
Danish
Dutch
English
Esperanto
Estonian
Faroese
Code
6566
6565
6570
8381
6577
6582
7289
6583
6588
6590
6665
6985
6678
6890
6672
6682
6671
7789
6669
7577
6765
9072
6779
7282
6783
6865
7876
6978
6979
6984
Area Codes
Area
Afghanistan
Argentina
Australia
Austria
Belgium
Bhutan
Bolivia
Brazil
Cambodia
Canada
Chile
China
Colombia
Congo
Costa Rica
Croatia
Czech Republic
Denmark
Ecuador
Egypt
El Salvador
18
7079Language
Fiji
Finnish
French
Frisian
Galician
Georgian
German
Greek
Greenlandic
Guarani
Gujarati
Hausa
Hebrew
Hindi
Hungarian
Icelandic
Indonesian
Interlingua
Irish
Italian
Japanese
Javanese
Kannada
Kashmiri
Kazakh
Kirghiz
Korean
Kurdish
Laothian
Latin
Latvian, Lettish
Code
7074
7073
7082
7089
7176
7565
6869
6976
7576
7178
7185
7265
7387
7273
7285
7383
7378
7365
7165
7384
7465
7487
7578
7583
7575
7589
7579
7585
7679
7665
7686
Language
Lingala
Lithuanian
Macedonian
Malagasy
Malay
Malayalam
Maltese
Maori
Marathi
Moldavian
Mongolian
Nauru
Nepali
Norwegian
Oriya
Panjabi
Pashto, Pushto
Persian
Polish
Portuguese
Quechua
Rhaeto-Romance
Rumanian
Russian
Samoan
Sanskrit
Scots Gaelic
Serbian
Serbo-Croatian
Shona
Sindhi
Code
7678
7684
7775
7771
7783
7776
7784
7773
7782
7779
7778
7865
7869
7879
7982
8065
8083
7065
8076
8084
8185
8277
8279
8285
8377
8365
7168
8382
8372
8378
8368
Language
Singhalese
Slovak
Slovenian
Somali
Spanish
Sudanese
Swahili
Swedish
Tagalog
Tajik
Tamil
Tatar
Telugu
Thai
Tibetan
Tigrinya
Tonga
Turkish
Turkmen
Twi
Ukrainian
Urdu
Uzbek
Vietnamese
Volapük
Welsh
Wolof
Xhosa
Yiddish
Yoruba
Zulu
Code
8373
8375
8376
8379
6983
8385
8387
8386
8476
8471
8465
8484
8469
8472
6679
8473
8479
8482
8475
8487
8575
8582
8590
8673
8679
6789
8779
8872
7473
8979
9085
Area
Malaysia
Maldives
Mexico
Monaco
Mongolia
Morocco
Nepal
Netherlands
Netherlands Antilles
New Zealand
Nigeria
Norway
Oman
Pakistan
Panama
Paraguay
Philippines
Poland
Portugal
Romania
Russian Federation
Code
MY
MV
MX
MC
MN
MA
NP
NL
AN
NZ
NG
NO
OM
PK
PA
PY
PH
PL
PT
RO
RU
Area
Saudi Arabia
Senegal
Singapore
Slovak Republic
Slovenia
South Africa
South Korea
Spain
Sri Lanka
Sweden
Switzerland
Taiwan
Thailand
Turkey
Uganda
Ukraine
United States
Uruguay
Uzbekistan
Vietnam
Zimbabwe
Code
SA
SN
SG
SK
SI
ZA
KR
ES
LK
SE
CH
TW
TH
TR
UG
UA
US
UY
UZ
VN
ZW
Choose a area code from this list.
Code
AF
AR
AU
AT
BE
BT
BO
BR
KH
CA
CL
CN
CO
CG
CR
HR
CZ
DK
EC
EG
SV
Area
Ethiopia
Fiji
Finland
France
Germany
Great Britain
Greece
Greenland
Code
ET
FJ
FI
FR
DE
GB
GR
GL
Heard and McDonald Islands HM
Hong Kong
HK
Hungary
HU
India
IN
Indonesia
ID
Israel
IL
Italy
IT
Jamaica
JM
Japan
JP
Kenya
KE
Kuwait
KW
Libya
LY
Luxembourg
LU
Troubleshooting
Ca
A menu is on the TV screen.
Check the following guide for the possible cause of a
problem before contacting service.
Co
Press the SETUP button to turn off the menu
screen.
Symptom/
Ca
Cause/
Co
Correction
Sy
No power.
Ca
The power cord is disconnected.
Co
Plug the power cord securely into the wall outlet.
Sy
The power is on, but the unit does not work.
Ca
The Rating level is set.
Co
Cancel the Rating function or change the rating
level.
Sy
Loud hum or noise is heard.
Ca
The disc is dirty.
Clean the disc.
The speakers and components are connected
poorly.
Co
ENGLISH
Sy
Ca
No disc is inserted.
Ca
Co
Insert a disc. (Check that the DVD or, audio CD
idicator in the DVD display is lit)
Co
Sy
No picture.
Ca
The unit is located too close to the TV.
Ca
The TV is not set to receive DVD signal output.
Co
Move your TV away from the audio components.
Co
Select the appropriate video input mode on the TV
so the picture from the unit appears on the TV
screen.
Sy
Radio stations cannot be tuned in.
Ca
The antenna is positioned or connected poorly.
Ca
Co
Connect the speakers and components securely.
The video cable is not connected securely.
Co
Connect the antenna securely.
Connect the video cable into the jacks securely.
Ca
The signal strength of the stations is too weak
(when tuning in with automatic tuning).
Ca
The connected TV power is turned off.
Co
Turn on the TV.
Co
Tune in the station manually.
Ca
No stations have been preset or preset stations
have been cleared (when tuning by scanning preset stations).
Preset the stations (page 14).
Sy
There is no sound or only a very low-level
sound is heard.
Ca
The equipment connected with the audio cable is
not set to receive DVD signal output.
Co
Sy
Select the correct input mode of the unit so you
can hear the sound from the unit.
The Remote Control does not work properly.
Ca
The Remote Control is not pointed at the remote
sensor of the unit.
Co
Point the Remote Control at the remote sensor of
the unit.
Ca
The Remote Control is too far from the unit.
Co
Ca
The audio cables are not connected securely.
Co
Connect the audio cable into the jacks securely.
Ca
The power of the equipment connected with the
audio cable is turned off.
Co
Turn on the equipment connected with the audio
cable.
Ca
The audio connecting cable is damaged.
Co
Replace it with new one.
Co
Use the Remote Control within about 23 ft (7 m).
Ca
There is an obstacle in the path of the Remote
Control and the unit.
Co
Remove the obstacle.
Ca
The batteries in the Remote Control are exhausted.
Sy
The playback picture is poor.
Ca
The disc is dirty.
Co
Replace the batteries with new ones.
Co
Clean the disc.
Sy
The front panel display is too dim.
Sy
The unit does not start playback.
An unplayable disc is inserted.
Ca
Nothing is displayed on the front panel display.
Co
Press DIMMER on the Remote Control.
Ca
Co
Insert a playable disc. (Check the disc type, colour
system and Regional code.)
Ca
The disc is placed upside down.
Co
Place the disc with the playback side down.
Ca
The disc is not placed within the guide.
Co
Place the disc on the disc tray correctly inside the
guide.
Ca
The disc is dirty.
Clean the disc.
Co
19
Specifications
General
Power supply
Power consumption
Net Weight
Refer to the main label.
Refer to the main label.
5.5 kg
External dimensions (W x H x D)
272 X 322 X 354 mm
Tuner/Amplifier
FM
Tuning Range
Intermediate Frequency
Signal to Noise Ratio
Frequency Response
AM Tuning Range
Intermediate Frequency
Signal to Noise Ratio
Frequency Response
Output Power
T.H.D
Frequency Response
Signal-to-noise ratio
87.5 - 108.0 MHz or 65 -74 MHz, 87.5 -108.0 MHz
10.7 MHz
60/55 dB (Mono/Stereo)
50 - 10000 Hz
522 - 1620 kHz or 520 - 1720 kHz
450 kHz
30 dB
140 - 1800 Hz
50 W + 50 W (4 Ω, THD 10 %) (MDD112)
30 W + 30 W (4 Ω, THD 10 %) (MDD72)
0.5 %
40 - 20000 Hz
75 dB
DVD/VCD/CD player
Frequency response (audio)
Signal-to-noise ratio (audio)
Signal-to-noise ratio (video)
Dynamic range (audio)
Video output
Component Video output
Cassette tape player
40 - 20000 Hz
More than 75 dB (1 kHz)
More than 55 dB (1 kHz)
More than 80 dB
1.0 V (p-p), 75 Ω
(Y) 1.0 V (p-p), 75 Ω
(Pb)/(Pr) 0.7 V (p-p), 75 Ω
Tape Speed
Wow Flutter
F.F/REW. Time
Frequency Response
Signal to Noise Ratio
Channel Separation
Erase Ratio
Speakers
Speaker Name
Type
Impedance
Frequency Response
Sound Pressure Level
Rated Input Power
Max. Input Power
Net Dimensions (W x H x D)
Net Weight
Front Speaker (L/R)
Bass Reflex 2Way 2Speaker
4Ω
55 - 20000 Hz (MDS112V)
60 - 20000 Hz (MDS72V)
83 dB/W (1m) (MDS112V)
83 dB/W (1m) (MDS72V)
50 W (MDS112V)
30 W (MDS72V)
100 W (MDS112V)
60 W (MDS72V)
220 X 326 X 242 mm
3.4 kg (MDS112V)
3.19 kg (MDS72V)
Designs and specifications are subject to change without notice for improvement.
3000 ± 3 % (MTT-111.
NORMAL-SPEED)
0.25 %
(MTT -111, JIS-WTD)
120 sec (C-60)
250 - 8000 Hz
43 dB
50 dB (P/B)/45 dB (R/P)
55 dB (MTT-5511)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement