LG A122CB.SP2, LS-C112PBL2 Owner's manual

LG A122CB.SP2, LS-C112PBL2 Owner's manual
website
http://www.lgservice.com
LG
ENGLISH
LG Room
Air Conditioner
ESPANOL
OWNER'S MANUAL
MODELS: SP2 Chassis
IMPORTANT
?
?
Please read this owner's manual
and
before
air conditioner.
installing
carefully
operating your room
thoroughly
Please retain this owner's manual for future reference after
reading
?
and
it
thoroughly.
aparato
Antes de utilizar el
de aire
manual
guardelo
en
con
el futuro.
detenimiento y
acondicionado,
lea este
para otras consultas
Room Air Conditioner Owner's Manual
TABLE OF CONTENTS
FOR YOUR RECORDS
Safety
Precautions.........................3
Write the model and serial numbers here:
Model #
Prior to
Operation
..........................9
Serial #
You
find them
can
on a
label
on
the side of each unit.
Dealer's Name
Introduction ..................................10
Date Purchased
Staple
your
receipt to this page in the event you need
purchase or for warranty issues.
it to prove date of
Electrical
Operating
Safety
...........................11
Instructions.................13
READ THIS MANUAL
Inside you will find many helpful hints on how to use
and maintain your air conditioner properly. Just a little
preventive care on your part can save you a great deal
of time and money
Maintenance and Service ............27
over
the life of your air conditioner.
You'll find many answers to common problems in the
chart of troubleshooting tips. If you review our chart of
Troubleshooting Tips first,
you may not need to call
for service at all.
PRECAUTION
?
Contact the authorized service technician for
repair
?
The air conditioner is not intended for
?
use
by
young children or invalids without supervision.
Young children should be supervised to ensure
that
?
Room Air Conditioner
maintenance of this unit.
Contact the installer for installation of this unit.
?
2
or
?
they
When
do not
the
play with
the air conditioner.
power cord is to
replacement work shall be
be replaced,
performed by
authorized personnel only using only genuine
replacement parts.
Installation work must be performed
in
accordance with the National Electric Code by
qualified and authorized personnel only.
Safety
Precautions
Safety
To
Precautions
prevent the injury of the
user or
other
people
and
property damage, the following instructions
must be
followed.
Incorrect
by
the
The
operation due to ignoring
following indications.
meanings
of the
instruction will
cause
harm
or
damage.
This
symbol
indicates the
possibility of
This
symbol
indicates the
possibility of injury or damage
symbols
used in this manual
are as
Be
Be
sure
death
The seriousness is classified
serious
or
ENGLISH
injury.
to
properties only.
shown below.
sure
not to do.
to follow the instruction.
Installation
Do not
use
For electrical
or a
use the power plug
and socket with the ground
work, contact
dealer, seller, a qualified
electrician, or an Authorized
damaged
cords, plugs,
power
loose
Always
the
socket.
terminal.
Service Center.
?
There is risk of fire
or
electric
?
shock.
or
electric
?
panel
and the
Do not
of control box
modify
or
extend the
Do not install, remove,
re-install the unit by
power cord.
securely.
?
There is risk of fire
shock.
There is risk of electric shock.
shock.
Install the
cover
There is risk of fire
or
yourself (customer).
or
electric
?
There is risk of fire
shock.
or
electric
?
There is risk of
fire, electric
shock, explosion, or injury.
Owner's Manual
3
Precautions
Safety
Be cautious when
For
unpacking and installing
the product.
contact the dealer
Sharp edges could cause injury.
Be especially careful of the
case edges and the fins on the
?
condenser and
Be
sure
?
There is risk of
fire, electric
shock, explosion, or injury.
the installation
product
defective installation
stand.
?
It may
cause
damage
injury, accident,
product.
or
to the
Do not let the air conditioner
area
run
age.
humidity
collapses,
the air
?
conditioner could fall with
it, causing
property damage, product failure,
and
on a
evaporator.
does not deteriorate with
If the base
or an
Authorized Service Center.
for
door
?
Do not install the
installation, always
or
a
long
time when the
is very high and a
a window is left open.
Moisture may condense and
wet
or
damage furnishings.
personal injury.
Operation
Take
care
to
ensure
that
Do not
power cords could not be
place anything
Do not turn the
on
the power cord.
air-conditioner ON
pulled out or damaged
during operation.
?
There is risk of fire
or
electrical
shock.
4
Room Air Conditioner
or
OFF
by plugging or unplugging
the power plug.
?
There is risk of fire
shock.
or
electric
?
There is risk of fire
shock.
or
electrical
Safety
?
Use
a
this
appliance.
dedicated outlet for
There is risk of fire
or
electrical
Grasp the plug
?
shock.
to
Do not
remove
place a heater or
appliances near the
the cord from the outlet. Do
other
not touch it with wet hands.
power cable.
There is risk of fire
electrical
or
Precautions
?
shock.
There is risk of fire and electric
shock.
ENGLISH
Do not allow water to
into electric
Do not store
run
Do not
or use
flammable gas or
combustibles near the air
parts.
use
the
tightly closed
long time.
product
in
space for
a
a
conditioner.
?
It may
cause
There is risk of
fire, failure of the product,
?
There is risk of fire
or
failure of
?
Oxygen deficiency
could
occur.
product.
or
electric shock.
Wax
When flammable gas leaks,
turn off the gas and open a
sounds, odors,
window for ventilation
comes
before turn the
DO NOT
or
?
Thinner
use
Unplug
the unit if
or
Stop operation
smoke
the window in storm
from it.
hurricane. If
product on.
telephone
remove
the
turn switches
There is risk of
on or
explosion
fire.
or
possible,
the air conditioner
from the window before the
off.
or
and close
strange
hurricane arrives.
?
There is risk of electrical shock
or
fire
?
There is risk of
damage,
property
failure of
product,
or
electric shock.
Owner's Manual
5
Safety
Do not open the inlet
grill of
product during
operation. (Do not touch the
When the
the
(flooded
electrostatic
Service Center.
is
?
Precautions
so
contact
filter, if the unit
product is soaked
submerged),
Ventilate the
an
product from
operating
time to time when
or
Authorized
it
together with
a
stove, etc.
equipped.)
There is risk of
electric
shock,
physical injury,
product
?
There is risk of fire
or
eletric
?
shock.
or
There is risk of fire
or
electrical
shock.
failure.
Unplug the appliance before
performing cleaning or
product is not be
long time,
disconnect the power supply
plug or turn off the breaker.
maintenance.
?
There is risk of electrical shock.
?
When the
Take
used for
nobody
a
There is risk of
or
failure,
or
product damage
care
to
ensure
could
step
that
on or
onto the outdoor unit.
?
unintended
This could result in
injury
and
personal
product damage.
operation.
Installation
Always check for gas
(refrigerant) leakage after
installation or repair of
product.
?
Low
refrigerant
cause
failure of
levels may
product.
Install the drain hose to
ensure
away
?
properly.
A bad connection may
water
Keep level even when
installing the product.
that water is drained
leakage.
cause
?
To avoid vibration
or
leakage.
90˚
6
Room Air Conditioner
water
fall
Safety
Do not install the
where the noise
Use two
product
or
hot air
lift and
from the outdoor unit could
the
damage
?
It may
or more
Do not install the
people to
transport the air
problem
for your
product
exposed to
(salt spray)
where it will be
conditioner.
sea
neighborhoods.
cause a
Precautions
wind
directly.
?
Avoid
personal injury.
?
It may
cause
corrosion
on
the
product. Corrosion, particularly
neighbors.
the condenser and
could
or
cause
inefficient
on
evaporator fins,
product malfunction
operation.
Operation
Do not direct airflow at
room
occupants. (Don't sit
in the
draft.)
Do not use the product for
special purposes, such as
preserving foods, works of
art, etc. It is
a consumer
conditioner,
not
a
Do not block the inlet
or
outlet of air flow.
air
precision
refrigeration system.
?
This could
damage
your health.
?
There is risk of
of
Use
not
a
soft cloth to clean. Do
use
harsh
solvents,
detergents,
damage
or
loss
?
cause
product failure.
Do not touch the metal
Do not
parts of the product when
anyting on the product.
(outdoor units)
removing the air filter. They
very sharp!
etc.
It may
property.
step
on or
put
are
?
There is risk of
fire, electric
to the
shock,
damage
parts of the product.
or
plastic
?
There is risk of
personal injury.
?
There is risk of
and failure of
personal injury
product.
Owner's Manual
7
ENGLISH
Precautions
Safety
Always insert the filter
securely. Clean the filter
every two weeks or
often if necessary.
Do not insert hands
objects through
more
or
dirty filter reduces the
efficiency of the air conditioner
and could cause product
malfunction or damage.
Use
a
firm stool
maintaining
or
?
ladder when
other
Do not drink the water
drained from the unit.
outlet while the air
conditioner is
A
?
or
the air inlet
There
parts
are
sharp
that could
plugged
and
in.
moving
personal
?
cause
It is not
cause
sanitary
and could
serious health issues.
injury.
cleaning
or
the air conditioner.
Replace the
all batteries in the remote
control with
new ones
not mix old and
new
of the
same
batteries
or
type. Do
different
types of batteries.
Be careful and avoid
?
personal injury.
?
There is risk of fire
or
explosion
Disuse
Do not
recharge
or
batteries. Do not
disassemble the
dispose
of batteries in
If the
liquid
from the batteries
gets
onto
your skin or clothes, wash it well with clean
water. Do not use the remote if the batteries
a
fire.
have leaked.
?
They
may burn
or
explode.
?
The chemicals in batteries could
other health hazards.
8
Room Air Conditioner
cause
burns
or
Safety
Prior to
for
Preparing
1. Contact
2.
3. Use
an
Operation
Operation
installation
in the power
Plug
Precautions
specialist
plug properly.
for installation.
ENGLISH
dedicated circuit.
a
4. Do not
use an
extension cord.
5. Do not
6. If the
start/stop operation by plugging/unplugging the power cord.
cord/plug is damaged, replace it with only an authorized replacement part.
Usage
1.
a long time may be hazardous to your health. Do not expose
plants to direct airflow for a long time.
Due to the possibility of oxygen deficiency, ventilate the room when using the appliance together with
stoves or other heating devices.
Do not use this air conditioner for non-specified special purpose (e.g. preserving precision devices,
food, pets, plants, or art objects). Such use may damage your properties.
Being exposed
to direct airflow for
occupants, pets,
2.
3.
Cleaning
or
and Maintenance
1. Do not touch the metal
2. Do not
3.
parts of the unit when removing the filter. Injury
water to clean inside the air conditioner.
can occur.
destroy the insulation,
leading to electric shock.
When cleaning the unit, first make sure that the power and breaker are turned off. The fan rotates at
very high speed during operation. There is a possibility of injury if the unit's power is triggered while
cleaning inner parts of the unit.
use
Exposure
to water
can
a
Service
For
repair and maintenance,
contact your authorized service dealer.
Owner's Manual
9
Introduction
Introduction
Symbols
used in this Manual
This
symbol
alerts you to the risk of electric shock.
This
symbol
alerts you to hazards that may
cause
harm to the
air conditioner.
This
NOTICE
symbol
indicates
special
notes.
Features
WARNING: This
regulations.
appliance should be installed in accordance with national wiring
guide acts as a guide to help to explain product features.
This
Indoor
NEO Plasma Filter
Signal Receptor
Front Panel
Air Filter
Power Cord
Air
Discharge
Outdoor
Air Intake Vents
Air Intake Vents
Connecting
Wires
Connecting
Wires
Air Outlet Vents
Piping
Piping
Drain Hose
Drain Hose
Base Plate
10
Room Air Conditioner
Air Outlet Vents
Base Plate
Electrical
Electrical
Safety
WARNING: This
To minimize the risk of electric
Safety
appliance
shock, you
must
must be
alway plug
properly grounded.
into
a
grounded
oulet.
Preferred method
Ensure proper ground
exists before use
WARNING:
power
Do not cut
or remove
the
grounding
prong from the
plug.
WARNING:
Attaching
receptacle
cover screw
the
adapter ground terminal to the wall
ground the appliance unless the
cover screw is metal and not insulated, and the wall receptacle is
grounded through the house wiring.
does not
WARNING:
If you have any doubt whether the air conditioner is
grounded, have the wall receptacle and circuit checked
properly
qualified
a
by
electrician.
Owner's Manual
11
Electrical
Safety
Temporary Use
of an
Adapter
We
strongly discourage the use of an adapter due to potential safety hazards. For temporary
use only a UL-listed adapter, available from most local hardware stores. Ensure that the
large slot in the adapter is aligned with the large slot in the receptacle for a proper polarity connection.
To disconnect the power cord from the adapter, use one hand on each to avoid damaging the ground
terminal. Avoid frequently unplugging the power cord as this can lead to eventual ground terminal
damage.
connections,
Temporary
method
Adapter Plug
Metal Screw
Receptacle
WARNING: Never
Temporary Use
We
use
appliance with
a
broken
adapter.
of an Extension Cord
strongly discourage the use of an extension cord due to potential safety hazards. For temporary
use only CSA certified and UL listed 3-wire grounded extension cords, rated 15 A, 125 V.
situations,
12
the
Cover
Room Air Conditioner
Operating
Instructions
Instructions
Operating
How to insert the Batteries
1. Remove the
battery
cover
it
by pulling
to the
according
arrow
ENGLISH
direction.
2. Insert
new
installed
batteries
making
that the
sure
(+)
and
(-)
of
battery
are
correctly.
3. Reattach the
cover
Use 2
NOTICE
by sliding
it back into
position.
AAA(1.5volt) batteries.
use rechargeable batteries.
Do not
Storage
?
and
Tips for using the Remote Controller
The remote controller may be stored
it on a wall.
by mounting
?
To
operate the
room
air
remote controller at the
conditioner, aim the
signal receptor.
Signal receptor
Receives the
signals
from the remote
controller.(Signal receiving
sound: two short
beeps
or one
long beep.)
Operation indicating lamps
On/Off
the
:
Lights
up
during
:
Lights
up
during Sleep
Timer
:
Lights
up
during
Defrost Mode
:
Sleep
Mode
system operation.
Timer
Mode Auto
operation.
operation.
Lights up during Defrost Mode or *Hot
operation (Heat pump model only)
Start
Outdoor Unit
:
Lights up during outdoor
(Cooling model only)
:
The function illustrates its
Operation
NEO Plasma
*Hot Start
operation: Stops
the indoor fan in
unit
operation.
dynamic
Heating Operation
mode
to
Operation indicating
lamps
by using
a
multiple lighting system.
prevent cold air from blowing
out from unit.
Owner's Manual
13
Operating
Instructions
Remote Control
The controls will look like the
Operations
following.
Controls
Signal
transmitter
1. START/STOP BUTTON
Operation starts when this button is pressed
and stops when the button is pressed again.
2. OPERATION MODE SELECTION BUTTON
Used to select the operation mode.
3. ROOM TEMPERATURE SETTING
BUTTONS
Used to select the room temperature.
4. INDOOR FAN SPEED SELECTOR
Used to select fan speed in four steps
low, medium, high and CHAOS.
5
5. JET COOL/HEATING(OPTIONAL)
Used to start or stop the speed
1
cooling/heaing.(speed cooling/heating operates
super high fan speed in cooling/heatig mode.)
6
6. CHAOS SWING BUTTON
Used to stop or start louver movement and
set the desired up/down airflow direction.
3
4
7. ON/OFF TIMER BUTTONS
Used to set the time of starting and
10
2
CANCEL
operation. (See
9
7
ON
12
AUTO CLEAN
8
17
13
14
15
16
stopping
24)
8. TIME SETTING BUTTONS
Used to adjust the time. (See page
SET
OFF
11
page
24)
9. TIMER SET/CANCEL BUTTON
Used to set the timer when the desired time
is obtained and to cancel the Timer
operation. (See
page
24)
10. SLEEP MODE AUTO BUTTON
Used to set Sleep Mode Auto operation.
(See
page
24)
11. AIR CIRCULATION BUTTON
Used to circulate the room air without
Flip-up door
(opened)
Operation
Mode
Operation
Healthy
or
Auto
Operation
Cooling Model(
),
Heat
Pump Model(
page
)
(OPTIONAL)
Used to set Auto Clean mode.
Room Air Conditioner
(See
page
22)
16. 2nd F Button
Used prior to using modes printed in blue
at the bottom of buttons. (See page 23)
17. AUTO CLEAN
14
25)
15. RESET BUTTON
Used prior to resetting time.
Heating Operation
?
heating. (See
14. HORIZONTAL AIRFLOW DIRECTION
CONTROL BUTTON (OPTIONAL)
Used to set the desired vertical airflow
direction.
Changeover
Dehumidification
or
13. NEO PLASMA(OPTIONAL)
Used to start or stop the
plasma-purification function.
Cooling Operation
Auto
cooling
12. ROOM TEMPERATURE CHECKING
BUTTON
Used to check the room temperature.
Operating
Instructions
Cooling operation
1
Press the
a
2
ENGLISH
Start/Stop button.
respond with
The unit will
beep.
Open the door of the remote controller. To select Cooling
Operation, press the Operation Mode Selection button.
Each time the button is pressed, the operation mode is
shifted in the direction of the
arrow.
Auto
Cooling
Healthy
Dehumidification
3
Close the door of the remote controller. Set the
lower than the
set within
a
room
temperature
temperature. The temperature can be
range of 18°C~30°Cat intervals of 1°C.
ON
4
Heating
(Heat pump model only)
Set the fan
speed again
To raise the
temperature
To lower the
temperature
with the door
of the remote controller still closed.
You
can select the fan speed in four
steps-low, medium, high and CHAOS.
Each time the button is pressed, the
fan speed mode is shifted.
Natural wind by the CHAOS
For fresher
blows like
a
feeling,
logic
press the Indoor fan
natural breeze
speed selector and set to CHAOS
by automatically changing fan speed according
mode. In this
mode, the wind
to the CHAOS
logic.
Owner's Manual
15
Instructions
Operating
Auto
operation (Cooling
model
1
Press the
Start/Stop button.
respond with
The unit will
a
2
only)
beep.
Open the door of the remote controller. To select Auto
Operation, press the operation mode selection button.
Each time the button is pressed, the operation mode is
shifted in the direction of the
arrow.
Auto
Cooling
Healthy
Dehumidification
3
ON
The
temperature and fan speed
electronic controls based
on
are
Heating
(Heat pump model only)
automatically
the actual
room
set
by
the
temperature. If
you want to change the set temperature, press the Room
Temperature Setting buttons. The cooler or warmer you feel,
the more times (up to two times) you should press the button.
The set temperature will be changed automatically.
To raise the
temperature
To lower the
temperature
During Auto Operation
You cannot control the indoor fan
If the
system is
not
operating
It has
already
been set
desired, manually switch
by the Fuzzy
rule.
to another mode. The
system will
not
cooling mode to the heating mode, or from heating mode to cooling
mode, it must be done by manually resetting.
During Auto Operation, pressing the chaos swing button makes the horizontal louvers swing up and
down automatically. If you want to stop auto-swing, press the chaos swing button again.
automatically
16
switch from the
speed.
as
Room Air Conditioner
Operating
Auto
changeover operation(Heat
1
Press the
Start/Stop button.
respond with
ENGLISH
beep.
Open the door of the remote controller. To select Auto Changeover
Operation, press the Operation Mode Selection button.
Each time the button is pressed, the operation mode is shifted in the
direction of the
arrow.
Cooling
3
only)
The unit will
a
2
pump model
Instructions
Auto
changeover
Healthy
Dehumidification
Heating
(Heat pump model only)
Close the door of the remote controller. Set the
lower than the
set within
a
room
temperature
temperature. The temperature can be
range of 18°C~30°Cat intervals of 1°C.
To raise the
temperature
To lower the
temperature
ON
4
Set the fan
speed again
with the door
of the remote controller still closed.
You
can select the fan speed in four
steps-low, medium, high and CHAOS.
Each time the button is pressed, the
fan speed mode is shifted.
During Auto changeover Operation
changes the operation
The air conditioner
mode automatically to keep indoor temperature. When
temperature vary over ±2°C with respect to setting temperature, air conditioner keeps the
temperature within ±2°C with respect to setting temperature by auto changeover mode.
room
room
Owner's Manual
17
Operating
Instructions
Healthy
dehumidification
operation
Press the
1
Start/Stop button.
respond with
The unit will
a
beep.
Open
2
the door of the remote controller. To select
Dehumidification
Operation,
press the
Healthy
Operation Mode
Selection button.
Each time the button is
pressed,
shifted in the direction of the
the
Auto
Cooling
operation
mode is
arrow.
Healthy
Dehumidification
3
Set the fan
speed again
Heating
(Heat pump model only)
with the door
of the remote controller still closed.
You
can select the fan speed in four
steps-low, medium, high, or CHAOS.
Each time the button is pressed, the
fan speed mode is shifted.
ON
Natural wind
by the
For fresher
feeling,
CHAOS
logic
press the Indoor Fan
to CHAOS mode. In this
breeze
Speed
Selector and set
mode, the wind blows like
by automatically changing
CHAOS logic.
fan
a
speed according
natural
to the
During Healthy Dehumidification Operation
If you select the dehumidification mode on the operation selection button, the A/C starts to run the
dehumidification function. It automatically sets the room temp. and airflow volume to the best condition
for
dehumidification, based
on
In this case, however, the setting
control the room temp. either.
the sensed current
temp.
is not
room
displayed
temp.
on
the remote controller and you
are
not able to
During the healthy dehumidification function, the airflow volume is automatically set according to the
optimization algorithm responding to the current room temp. status, so that the room condition is kept
healthy and comfortable even in the very humid season.
18
Room Air Conditioner
Operating
Heating operation (Heat
pump model
1
Press the
only)
beep.
Open the door of the remote controller. To select Heating
Operation, press the Operation Mode Selection button.
Each time the button is pressed, the operation mode is
shifted in the direction of the
arrow.
Auto
Cooling
3
ENGLISH
Start/Stop button.
respond with
The unit will
a
2
Instructions
Healthy
Dehumidification
Heating
(Heat pump model only)
Close the door of the remote controller.
Set the
The
temperature higher than the room temperature.
temperature can be set within a range of 16°C~30°Cat
intervals of 1°C.
ON
4
Set the fan
To raise the
temperature
To lower the
temperature
speed again
with the door of the
remote controller still closed. You
select the fan
speed
in four
can
steps--low,
medium, high and CHAOS. Each time the
button is
pressed,
the fan
speed
mode is
shifted.
Natural wind
For fresher
by the
feeling,
wind blows like
a
CHAOS
logic
press the Indoor Fan
natural breeze
Speed Selector and set to CHAOS
by automatically changing fan speed according
mode. In this
to the CHAOS
mode, the
logic.
Owner's Manual
19
Operating
Instructions
Jet cool
operation
1
Press the
a
2
beep.
Press the Jet Cool button to
the
speed cooling
will
on
3
Start/Stop button.
respond with
The unit will
operate
mode and the unit
at super high fan speed
mode for 30 minutes.
operate
cooling
To cancel the Jet Cool
fan
speed button
again and the unit
mode, press the Jet Cool button, the
room temperature setting button
will operate at high fan speed on cooling
the
or
mode.
or
or
NOTICE
During the JET COOL function at any moment, the A/C starts to blow the cool air at extremely
high speed for 30 minutes setting the room temp. automatically to 18°C. It is especially used to
cool the room temp. quickly in a hot summer.
In heat pump mode, neuro
function is not available.
fuzzy mode,
In order to return to the normal
mode selection
auto
changeover
mode
however, the JET COOL
cooling mode from the JET COOL mode, just press the operation
button, airflow volume selection, temp. setting button or the JET COOL button
again.
20
or
Room Air Conditioner
Operating
Jet heat
Instructions
operation (Optional)
Press the
1
Start/Stop button.
respond with
ENGLISH
The unit will
a
beep.
Open
2
the door of the remote controller.
To select
Heating Operation.
Auto
Cooling
Healthy
Dehumidification
changeover
Press the Jet Heat button to
3
speed heating
Heating
(Heat pump model only)
operate the
mode and the unit will
at super high fan
mode for 60 minutes.
operate
speed
on
heating
ON
To cancel the Jet Heat
4
mode, press the Jet Heat button,
the fan
speed button or the room temperature setting
button again and the unit will operate at high fan speed on
heating mode.
or
or
NOTICE
During the JET HEAT function at any moment, the A/C starts to blow the heat air at extremely high speed for
setting the room temp. automatically to 30°C. It is especially used to heat the room temp. quickly
60 minutes
in
a
On
cool winter.
cooling, healthy dehumidification
mode
or
auto
changeover mode, however,
the JET HEAT function is not
available.
In order to return to the normal
selection
heating
mode from the JET HEAT
button, airflow volume selection, temp. setting button
or
mode, just press the operation mode
the JET HEAT button
again.
Owner's Manual
21
Operating
Instructions
NEO PLASMA
purification operation(Optional)
1
Press the
Start/Stop button.
respond with a
The unit will
beep.
2
Open
the door of the remote
controller. Press the PLASMA
button.
Operation will start when the button
is pressed and stop when the button
is pressed again.
3
Set the fan
speed again
controller closed. You
with the door of the remote
can
select the fan
speed
in four
steps-low, medium, high or CHAOS.
Each time the button is pressed, the fan
speed mode is shifted.
Air
purifying operation (PLASMA) can be
cooling, Heating or any other operations.
with
NEO PLASMA Air
Purifying Operation only
If you press the only PLASMA button, only
PLASMA purification function operates.
Then, fan speed is low. You can select the fan
speed in four steps-low, medium, high or
CHAOS.
Each time the button
speed
22
Room Air Conditioner
(
mode is shifted.
)
is
pressed,
the fan
Operating
2nd F
Instructions
operation
1
Press the
a
2
ENGLISH
Start/Stop button.
respond with
The unit will
beep.
Open
the door of the remote control and press the 2nd
operate functions printed in blue unter
Function button to
buttons.
(Check the indication
remote controller.)
These buttons
can
of 2nd function
set the timer
ON
as
on
the
display
of the
follows:
OFF
SET
CANCEL
ON
OFF
SET
AUTO CLEAN
3
For
2nd function
the button is
more
disappears in a
pressed again.
short time
details, refer to functions
automatically or when
next pages.
Owner's Manual
23
Instructions
Operating
Additional Features
mode
Sleep
1. Press the
2. The Timer is
sleep
Mode Auto button to set the time you want the unit to
Sleep
in one-hour increments
programmed
stop automatically.
by pressing the Sleep Mode Auto button 1 to 7 times. The
period in steps of 1 hour, press the Sleep Mode
mode is available for 1 to 7 times. To alter the time
Button while
aiming at air conditioner.
Sleep Mode Auto LED lights up.
cancel the Sleep Mode, press the sleep Mode
) disappears from the operation display.
3. Make
To
(
sure
The
Sleep Mode will be operated
only) for a comfortable sleep.
NOTICE
In
cooling
The
the
mode
or
at slow fan
speed (cooling)
or
medium fan
speed (heat
pump
mode:
healthydehumidification
temperature will automatically rise by 1°C
Auto button several times until the star
over
the next 30 minutes and
by
2°C in 1 hour for
a
comfortable
sleep.
Setting
the time
1. Time
can be set only when you press the Reset button. Having replacing the batteries,
you should press the reset buttons to reset the time. Press the Start/Stop button.
2. Press 2nd F button and check if 2nd F icon is
3. Press the Time
Setting
on.
buttons until the desired time is set.
CANCEL
4. Press the Timer SET button.
SET
Check the indicator for A.M. and P.M.
NOTICE
Delay
1. Make
sure
start/Pre-set
the time is set
stop
correctly on
the
display
of the remote controller.
2. Press 2nd F button.
3. Press the ON/OFF Timer buttons to turn Timer
4. Press the Time
Setting
on or
off.
ON
OFF
buttons until the desired time is set.
CANCEL
5. To set the selected
time, press the Timer setting button aiming the
remote controller at the
SET
signal receptor.
To cancel the timer
setting
Check if 2nd F icon is off.
CANCEL
Press the Timer Cancel button
(The timer lamp
NOTICE
Delay
24
on
Select
aiming
the remote controller at the
the air conditioner and the
one
of the
following
OFF Timer
Room Air Conditioner
Delay
four
display will
go
SET
out.)
types of operation.
ON Timer
signal receptor.
Delay
with the unit
OFF and ON Timer
running
Delay
ON and OFF Timer
Instructions
Operating
Airflow direction control
The
up/down and right/left
using the remote control.
airflow
be
can
Press Chaos
adjusted by
Swing
Press the button
30
Press the
button to start the unit.
Start/Stop
button and the louvers will
and the louvers will
again
minutes, the louvers
swing.
stop. After
return to the maximum airflow
position automatically.
Air circulation mode
Circulates the
1. Press the
2.
Open
room
air without
Start/Stop
the door
cooling
or
heating.
button. the unit will
respond
Now each time that you press the Indoor Fan
and back to low again.
CHAOS Air
NOTICE
with
a
beep.
the remote control. Press the Air Circulation button. Close the door
on
Speed Selector,
Fan
speed
is
on
low.
the fan
Fan
speed
speed
is
on
on
the remote control.
is shifted from low to CHAOS
medium.
Fan
speed
is
on
high.
CHAOS Air economizes power
automatically changed
from
consumption and prevents overcooling. The fan speed is
high to low or vice versa, depending on the ambient temperature.
Auto clean
1. Whenever you press the Auto Clean
button, Auto Clean Function will be reserved and cancelled.
2. Auto Clean function works before and after
AUTO CLEAN
the below
cooling
or
dehumidification mode. For
details, refer to
points.
3. When the unit is started after the reservation of Auto Clean
,the Cool Start function operates and
indoor Fan is started after 20 seconds.
4. When you press Start/Stop button to turn off the unit after the you have reserved Auto Clean
function, the air-conditioner circulates the indoor air in the Auto Clean mode with no more
Cooling
pump
Dehumidification
or
model, for
operation.
For
Cooling only model,
it lasts for 30 minutes for Heat
16 minutes.
5. If you press the auto clean button
cancelled.
again during the product operation
,
Auto Clean function will be
NOTICE
During
Auto Clean
Dehumidification
During
function, moistures left in indoor units after Cooling Operation
Operation
Auto Clean
can
or
Healthy
be removed.
function, only Start/Stop button, Plasma button and Auto Clean button
are
available.
Owner's Manual
25
ENGLISH
Operating
Instructions
Forced
operation
Operation procedures when the remote control can't be used.
operation will be started if the power button is pressed.
If you want to stop operation, re-press the button.
The
Power button
Cooling
Operating
mode
Indoor FAN
Speed
Test
operation
During
the TEST
<
24°C
Room
Temp. < 21°C
Cooling
Cooling
Healthy Dehumidification
Heating
High
High
High
High
OPERATION, the unit operates in cooling mode
at
high speed fan, regardless
of
room
resets in 18 minutes.
During test operation,
If you want to
Room Temp. ≥ 24°C2 1 °C ≤ Room Temp.
22°C2 2 °C2 3 °C2 4 °C
Setting Temperature
temperature and
Heat pump Model
Model
use
if remote controller
this
signal
is
received, the unit operates
as
remote controller sets.
Press and hold the ON/OFF button for 3~5seconds, then the buzzer sound 1
operation,
"beep".
If you want to
stop the operation, re-press the button.
Auto restart
In case the power comes on again after a power failure, Auto Restarting Operation is the function to operate
procedures automatically to the previous operating conditions.
So there is no need of activating this function by pressing any key or button.
In the initial mode, the fan operates at a low speed and the compressor starts 2.5~3minutes later.
As the compressor starts, the fan speed also resumes its previous setting mode.
Helpful
information
Fan
and
speed
cooling capacity.
cooling capacity indicated in the specification is the value
when the fan speed is set to high, and the capacity will be lower
at low or medium fan speed.
High fan speed is recommended when you wish to cool the room
quickly.
The
High
Speed
NOTICE
Auto restart function has set enable
But customer
can
set up
as
by following
factory default.
this instruction.
To be disable function
-
Press and hold the ON/OFF button for 6
seconds, then the buzzer sound
2
"beep"
and the indicator
lamp (1)
seconds, then the buzzer sound
2
"beep"
and the indicator
lamp (1)
blinks 4 times.
To be enable function
-
Press and hold the ON/OFF button for 6
brights
26
4 times.
Room Air Conditioner
Maintenance and Service
Maintenance and Service
Indoor Unit
WARNING: Turn the
Do not
NOTICE
use
Supply
bleach
system off before cleaning. To clean, wipe with
or
a
soft, dry cloth.
abrasives.
power must be disconnected before
cleaning
the indoor unit.
Air filter
The air filters behind the front
grill
should be checked and cleaned
every 2 weeks or more often if neccessary.
1. Lift the front panel. After lifting up the filter tab
out
bit, take the filter
Filter
slowly
NOTICE
Clean the filter after
2. Clean the filter with
3.
a
once
?
If dirt is
?
If hot water
stopping
a vacuum or
the
product.
warm, soapy water.
conspicuous, wash with a solution of detergent in
(40°C or more) is used, it may be deformed.
After washing with water, dry well in the shade.
lukewarm water.
4. Re-install the air filter.
Filter
Never
?
use
followings:
Water hotter than 40°C.
Could
?
any of the
cause
deformation and/or discoloration.
Volatile substances
Could
damage
the surfaces of the air conditioner.
Outdoor Unit
The heat
exchanger coils and panel vents of the outdoor
clogged with dirt or soot, the heat exchanger
and panel vents may be professionally steam cleaned.
unit should be checked
regularly.
If
NOTICE
Dirty or clogged coils will reduce the
operating efficiency of the system and
higher operating costs.
(Rear)
cause
Air intake
vents
(Side)
Piping
Drain Hose
Air outlet
vents
(Rear)
Air intake
vents
Air outlet
vents
(Rear)
(Side)
Piping
Air intake
vents
Drain Hose
(Side)
Piping
Drain Hose
Air outlet
vents
Owner's Manual
27
ENGLISH
Maintenance and Service
Cleaning
?
Recomended
1. Lift the front
Filter
use
period
panel,
:
About 3 months
hold it up and
pull
the Air filter.
Front Panel
Air Filter
2. Remove the Plasma Filter.
WARNING: Don't touch the PLASMA Filter
within 10 seconds after
grille,
it may
cause
opening
the inlet
electric shock.
Plasma Purifier
Filter
3. Put the Plasma Filter into the neutral
detergent
for 1~2
hours and then raise it.
4. Insert the Plasma Filter after
perfectly drying it in shade.
panel completely
Now insert Air Filter and close the front
by matching
the hook.
Front Panel Hook
Air Filter
Air Filter
28
Room Air Conditioner
Hook-Hanger
Maintenance and Service
Common Problems and Solutions
Before
calling
for service
If you have problems with your air conditioner, read the following information and try to solve
the problem. If you cannot find a solution, turn off the air conditioner and contact your dealer.
Air conditioner does not
operate
1. Ensure that the air conditioner is
2. Check the fuse
or
plugged
into
a
proper outlet.
circuit breaker.
3. Check whether the
voltage
is
unusually high
or
low.
Air does not feel cold
1. Ensure that the
2. Check to
see
if
enough on the cooling setting
temperature settings are correct.
the air filter is clogged with dust. If so, replace
the filter.
3. Ensure that the air flow from the outside is not obstructed and that there is
over
20" between the back of the air conditioner and the wall
4. Close all doors and windows and check for any
Before
calling
for
source
a
clearance of
fence behind it.
or
of heat in the
service, please review the following list of
room.
common
problems
and
solutions.
The air conditioner is
?
You hear
or
in
and
?
a
pinging
operating normally when:
noise. This is caused
by
humid conditions. This feature is
highly
improve cooling efficiency.
water
being picked up by
designed to help remove
You hear the thermostat click. This is caused
by
the compressor
the fan
on
rainy days
moisture in the air
cycle starting
and
stopping.
?
You
see
highly
water
dripping
humid conditions
from the
or on
rear
of the unit. Water may be collected in the base pan in
This water overflows and drips from the rear of
rainy days.
the unit.
?
You hear the fan
running
while the compressor is silent. This is
a
normal
operational
feature.
Owner's Manual
29
ENGLISH
Maintenance and Service
Troubleshooting
The air conditioner may be
Problem
operating abnormally
when:
Possible Causes
The air conditioner is
What To Do
?
unplugged.
The fuse is blown/circuit
breaker is
?
sure
the air conditioner
is
plug
into the outlet.
Check the house fuse/circuit breaker
box and
tripped.
Air
Make
pushed completely
replace
the fuse
or
reset the
breaker.
conditioner
does not start
Power failure.
?
If power failure occurs, turn the mode
control to Off.
When power is restored, wait 3
minutes to restart the air conditioner
to
prevent tripping of the compressor
overload.
Airflow is restricted.
?
Make
sure
blinds,
or
there
are no
furniture
curtains,
blocking
the front of
the air conditioner.
The thermostat may not be
set
?
The air filter is
dirty.
Turn the knob to
a higher number.
highest setting provides
maximum cooling.
The
high enough.
?
Clean the filter at least every 2 weeks.
See the care and Maintenance
section.
Air
The
conditioner
room
may have been
?
hot.
on, you need to allow time for the
room to cool down.
does not cool
as
When the air conditioner is first turned
it should
Cold air is
Cooling
escaping.
coils have iced up.
?
Check for open furnace floor
and cold air returns.
?
See Air Conditioner
registers
Freezing Up
below.
Air
Ice blocks the air flow and
the air conditioner from
conditioner
stops
freezing
cooling
*
You
30
can
up
refer to the
the
Energy
Room Air Conditioner
?
Set the mode control at
High
room.
Star program in detail at
High
Fan
Cool with thermostat at 1
www.energystar.gov.
or
or
2.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement