LG | FFH-196A | Owner's Manual | LG FFH-196A Owner's Manual

LG FFH-196A Owner's Manual
FFH-192/195/196-ENG(056E)
HI-FI MICRO CD COMPONENT SYSTEM
OWNER'S MANUAL
MODELS:
FFH-192A, FE-192E
FFH-195A, FE-195E
FFH-196A, FE-196E
Please read this manual
carefully
before
operating
your set.
Retain it for future reference.
Designs
and
specifications are subject
improvement.
without notice for
to
change
Precautions
de
Reglement
le materiel
sur
brouilleur de Canada.
AVERTISSEMENT
CAUTION
RISQUE DE CHOC ELECTRIQUENE-PAS OUVRIR
RISK OF ELECTRIC
(FOR CUSTOMERS
SHOCK DO NOT OPEN
IN THE UNITED STATES OF
AMERICA)
NOTE:
Note to CATV
system Installer:
provided to call the CATV system installer's attention
provides guidelines for proper
grounding and, in particular, specifies that the cable ground shall be
connected to the grounding system of the building, as close to the
point of cable entry as practical.
The interference potential to the device.
This equipment generates and uses radio frequency energy and if not
installed and used properly, that is in strict accordance with the
manufacturer's instructions, may cause interference to radio and
tel-
CAUTION:TO REDUCE THE RISK OF
This reminder is
ELECTRIC SHOCK
DO NOT REMOVE
to Article 820-40 of the NEC that
COVER(OR BACK)
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
Explanation Graphical Symbols:
The lightning flash with
an equilateral triangle
user
arrowhead
symbol,
within
is intended to alert the
to the presence of uninsulated dangerous
evision
within the product's enclosure that may be
of sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence
of important operating and maintenance(servicing) instructions in the literature accompanying
the appliance.
voltage
a
cations in
TO REDUCE THE RISK OF FIRE OF ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
To avoid electrical shock, do not open the cabinet, Refer servicing to
personnel only.
It has been
Class B
subparts
computing
type tested and found
to
comply
with the
device in accordance with the
J of Part 15 of FCC Rules, which
are
specifidesigned to
protection against such interference in a residential
installation. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user in encouraged to try to correct
the interference by one of more or the following measures:
Reposition or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that
provide
WARNING:
qualified
reception.
limits for
reasonable
-
-
-
to which the receiver is connected.
CAUTION
Use of controls
adjustments or performance of procedures
specified herein may result in hazardous radiation
than those
or
other
expo-
sure.
-
Consult the dealer
(FOR CUSTOMERS
or an
experienced radio/TV technician
KINGDOM)
for
help.
IN THE UNITED
WIRING INSTRUCTIONS
The
apparatus shall not be exposed to dripping or splashing and that
objects filled with liquids, such as vases, shall be placed on the
apparatus.
(FOR THE CUSTOMERS IN EUROPE)
If this product is marked with the CE-symbol, it means which is
conforms to EMC regulation 89/336/EEC.
no
component in this product is capable of emitting radiation
exceeding the limit for Class 1.
LASERSTRALNING
AR FARLIG.
NAR
DENNA DEL
AR
IMPORTANT
The wires in this mains lead
following
Attention:Quand
s'exposer
aux
l'appareil est ouvert, ne pas
radiations invisibles du faisceau laser.
This label is located
on
LASER
PRODUCT
LASER
PRODUKT
LUOKAN 1
LASER
LAITE
KLASS 1
LASER APPARAT
CLASSE 1
PRODUIT LASER
:
coloured in accordance with the
:
Neutral
Live
As the colour of the wires in the mains lead of this
This
KLASSE 1
are
codes:
Blue
Brown
the interior.
CLASS 1
If the mains sockets in your home differ, or are not suitable for the type
plug supplied, then the plug should be removed and a suitable type
wiring instructions below:
Warning: The mains plug severed from the mains lead of this appliance
must be destroyed. A mains plug with bared wires is hazardous if
engaged in a mains output line socket.
INTERLOCKS DEFEATED. AVOID EXPOSURE TO BEAM.
STRALEN
TRONICS U.K.LTD"
fitted. Please refer to the
CAUTION:INVISIBLE LASER RADIATION WHEN OPEN AND
OPPNAD
appliance is supplied with a BS1363 approved 3 amp fused mains
plug. When replacing the fuse always use a 3 amp BS1362 approved
type. Never use this plug with the fuse cover omitted. To obtain a
replacement fuse cover contact your supplying dealer or "LG ELEC-
of
Laser
VARNING:OSYNLIG
This
Compact
Disc
player
is classified as a CLASS
1 LASER product.
The CLASS 1 LASER
PRODUCT label is
located on the exterior.
correspond with the coloured markings identifying
plug, proceed as follows:
appliance may not
the terminals in your
The wire which is coloured blue must be connected to the terminal
which is marked with the letter N
or
coloured black.
The wire which is coloured brown must be connected to the terminal
which is marked with the letter L
or
coloured red.
If
(FOR
CUSTOMERS IN
a 13 amp BS1363 plug or any other type of plug is used, 3 amp
BS1362 approved fuse must be fitted either in the plug or at the distri-
CANADA)
CAUTION:TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS
bution board.
PLUG WITH AN EXTENSION CORD,
RECEPTACLE, OR OTHER OUTLET UNLESS THE BLADES CAN BE
Warning:
(POLARIZED)
FULLY INSERTED TO PREVENT BLADE EXPOSURE.
This class B
digital apparatus meets all requirements of the canadian
Interference-Causing Equipment Regulations.
Warning:
Do not install this equipment in a confined space such a book case or
similar unit.
WARNING:
SHOCK HAZARD
DO NOT OPEN
-
MISE EN GARDE:
Pour eviter
avec une
les chocs
rallonge,
pas y inserer
Cet appareil
2
un
electriques,
receptacle
n'utilisez pas cette fiche (polariesee)
autre prise si vous ne pouvez
ou une
les brouches a fond.MISE EN GARSDE
numerique
de la classe B
respecte
toutes les
exigences
Do not connect either wire to the earth pin, marked with the letter E
with the earth symbol
or coloured green or green and yellow.
or
Table of Contents
INTRODUCTION
OPERATION
Precautions...........................2
Presettingtheradiostations.
TableofContents......................3
Listeningtotheradio..................11
BeforeUse...........................4
TapePlayback........................12
BasicPlayback......................12
ToStopPlay........................12
TapeCounterReset..................12
.12
ToPlayFastRewindorFastForward.
SafetyPrecautions....................4
NotesonDiscs......................4
NotesonRemoteControl...............4
.
.
.
.
.
.
.
.
.
FrontPanel/RearPanel.................5
RemoteControl........................6
DisplayWindow........................6
Connections..........................7
SpeakerSystemConnection.
Antenna(Aerial)Connections.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
SettingtheVoltage(OPTIONAL).
.
.
.
.
.
.
.
.
.
.7
.7
BEFORE OPERATION
.8
SettingtheCLOCK.....................8
SleepFunction........................8
.
.
.
.11
.
Recording...........................12
BasicSetting.......................12
Recording from Radio, CD or Auxiliary
source............................12
CD to
Tape Synchronized Recording
.
.
.
.
.
12
CDPlayback.........................13
BasicPlayback......................13
ToPausePlay......................13
ToStopPlay........................13
ToSkippingtheTrack.................13
.13
ToPlayFastRewindorFastForward.
ToRepeatPlay......................13
ToProgramPlay....................14
.
.
.
TimerFunction........................9
AudioAdjustment.....................10
VolumeAdjustment..................10
.10
SoundQualityAdjustment.
.
.
.
.
.
.
.
.
.
.
.
REFERENCE
Troubleshooting......................14
Specification.........................15
MUTE............................10
SURROUND.......................10
XDSS
(Extreme Dynamic
Sound
System)
.
.
.
.
About the
10
AuxiliaryFunction.....................10
symbols
Indicates hazards
for instructions
likely
to
unit itself
or
other material
Indicates
special operating
cause
harm to the
damage.
features of this
unit.
Indicates
tips
and hints for
making
the task
easier.
3
INTRODUC
Before Use
Precautions
Safety
shipping the unit
The
original shipping carton and packing materials
come in handy. For maximum protection, re-pack the
unit as it was originally packed at the factory.
To
discs
Fingerprints and dust on the disc can cause poor
picture quality and sound distortion. Before playing,
clean the disc with a clean cloth. Wipe the disc from
the unit
Handling
When
Cleaning
the center out.
keep the surface clean
Do not
near
use
volatile
liquids,
such
as
the unit. Do not leave rubber
contact with the unit for
leave marks
Cleaning
a
insecticide spray,
or
long period
plastic products in
of time. They will
the surface.
on
spray intended for
the unit
To clean the cabinet
Use
a
soft, dry cloth. If the surfaces
soft cloth
use a
lightly
solution. Do not
benzine,
or
use
thinner,
are
moistened with
a
extremely dirty,
mild detergent
strong solvents, such
as
Do not use strong solvents such as alcohol, benzine,
thinner, commercially available cleaners, or anti-static
these
as
might damage
alcohol,
Notes
on
records.
analog
Remote Control
Remote Control
the surface
Operation Range
Point the remote control at the remote
of the unit.
sensor
and press
the buttons.
Distance:
Notes
on
Discs
remote
Angle:
Handling
Hold the disc
get
on
by
playback side of the disc.
edges so that fingerprints
the
or
tape
on
from the front of the
Remote control
sensor.
battery
installation
will not
Detach the
the surface.
Do not stick paper
(7 m)
sensor.
About 30° in each direction of the front of the
remote
discs
Do not touch the
About 23 ft
battery
cover on
the
rear
of the remote control, and insert two
the disc.
R03
(size AAA)
and
batteries with
aligned correctly.
Caution
Do not mix old and
Storing
After
playing,
store the disc in its
case.
Do not expose the disc to direct sunlight or sources of
heat, or leave it in a parked car exposed to direct
as there may be
increase inside the car.
sunlight,
4
new
batteries. Never mix different
types of batteries (standard, alkaline, etc.).
discs
a
considerable temperature
Front Panel/ Rear Panel
26
25
24
12
34
22
56
20
78
18
27
23
OPTIONAL
21
910
16
INTRODUC
AM
19
17
AUX
L
15
28
R
14
11
13
12
L
29
R
31
1.
DISPLAY
2.
?
BACKWARD PLAY
?
PRESET
?
PLAY MODE button
?
COUNTER RESET button
3.
4.
5.
30
19. AM/ FM SELECT
(
)
button
:
:
21.
OPTIONAL
:
RECORD/ RECORD PAUSE
REC
?
TUNING
TUNER/ CD/ TAPE/ AUX indicators
-
button
TUNER
)button-CD
?
SEARCH
?
FAST FORWARD PLAY
button
)
button
(+)
?SKIP(
OPTIONAL
(
button
(FUNCTION)
(TUNER/ CD/ TAPE/ AUX)
button
(-)
(BAND)
20. FUNCTION SELECT
OPTIONAL
(+)
button
-
CD
(
)
button
-TAPE/ CD
6.
POWER
7.
VOLUME
8.
CD SYNC. button
9.
PROG./ MEMORY button
(
STANDBY/ON)
(-)/(+)
button
22.
knob
10. HEADPHONE SOCKET
(
):
(EQ)
PUSH EJECT
13.
SKIP
23.
24.
-DECK
14. XDSS button
?
SEARCH
?
FAST REWIND PLAY
(-)
button -CD
FORWARD PLAY
?
PRESET
(+)
?
STOP
)
?
CLEAR button
(
25. CD
26. CD DOOR
17. MODE/RIF button
(
SET
?
COUNTER RESET button
(CLOCK/ TIMER)
button
OPTIONAL
(
)
button
button
button
OPEN() button
(COUNTER)
28. AUXILIARY INPUT SOCKET
:
29. SPEAKER TERMINAL
30. VOLTAGE SELECT SWITCH
(CD
button
)
27. ANTENNA TERMINAL
?
CD PAUSE
TUNER
)
?
16. CLOCK button
?
-
button -CD
(
15. TIMER button
18.
button
(-)
-TAPE/ CD
button
position
TUNING
?
3.5mm
11. SURROUND button
12. EQUALIZER
?
)
button
:
OPTIONAL
31. POWER CORD
5
Remote Control
1.
1
X
2345
XDSS button
2.
POWER button
3.
TUNER/ BAND button
13
4.
AUX button
12
5.
PRESET
6.
CD FUNCTION buttons
11
10
(
)
button
?
PLAY/ PAUSE
(
?
CD
button
STOP(
)
button
)
?SKIP(
9
?
6
/
)button
FAST REWIND/ FAST FORWARD PLAY
(
?
8
7.
7
/
)button
REPEAT button
TAPE FUNCTION buttons
?
RECORD/ RECORD PAUSE button
?
BACKWARD PLAY button
?
?
FORWARD PLAY
(
(
FAST FORWARD PLAY
?
FAST REWIND PLAY
SLEEP button
9.
PROGRAM button
10. VOLUME CONTROL
11.
:
)
button
)
?
8.
(
(
(
(
)
)
EQUALIZER PATTERN
button
button
(EQ PATT.)
button
12. MUTE button
13. SURROUND
button
(SURR.)
Display Window
34
2
5
67
XDSS
TIMER
SLEEP
MUTE
REC
SYNC
89
PROG.
STEREO
REPEAT
1 ALL
10
11
12
RC
1
kHz
MHz
13
1.
MUTE indicator
8.
FM STEREO indicator
2.
CD PLAY/ PAUSE indicator
9.
CD REPEAT indicator
3.
XDSS
4.
TIMER indicator
11. TAPE PLAY DIRECTION indicator
5.
CD SYNCHRO RECORDING indicator
12. PLAY MODE indicator
6.
SLEEP indicator
13.
7.
PROGRAM
6
(Extra Dynamic
indicator
Sound
System)
indicator
10. RECORD/ RECORD PAUSE indicator
(OPTIONAL)
?
VOLUME indicator
?
SOUND LEVEL METER
)
OPTIONAL
)
button
)
TAPE STOP button
(
Connections
Speaker System
Connect the
Connection
speakers using the supplied speaker cords by matching the colors of the terminals and those
possible surround sound, adjust the speaker parameters (distance, level, etc.).
of the
cords. To obtain the best
INTRODUC
AUX
L
R
red
L
black
R
red
Right speaker
Left
speaker
Notes
?
Be
sure
to match the
If the cords
are
speaker cord to the appropriate terminal on the components:
reversed, the sound will be distorted and will lack base.
?
If you use front
the speakers.
?
Do not disassemble the front
Antenna
speakers
with low maximum
cover
of
input rating, adjust
the volume
+
carefully
to
+
and
--
to
--.
to avoid excessive
output
on
supplied speaker.
(Aerial) Connections
Connect the
?
Connect
?
Connect
supplied FM/AM antennas for listening to the radio.
the AM loop antenna to the AM antenna connector.
the FM wire antenna (or FM "T" antenna) to the FM 75Ω/300Ω
coaxial connector.
FM external
antenna
(aerial)
(not supplied)
FM indoor antenna
(aerial)
AM
loop antenna (aerial)
(Supplied)
Position it for
the best
AM
(MW) loop
(aerial)
(Supplied)
FM external
antenna
antenna
(aerial)
(not supplied)
For AM
AM
the
loop
(MW) reception, connect
antenna (aerial) to the
AM
terminal marked AM
FM 75
reception
300 ohms
coaxial
cable
FM
FM wire antenna
(supplied)
Notes
?
?
?
To prevent noise pickup, keep the AM loop antenna away from the unit and other components.
Be sure to fully extend the FM wire antenna.
After
connecting
the FM wire antenna,
keep
it
as
horizontal
as
possible.
7
the
Setting
Voltage (OPTIONAL)
If your set is equipped with a voltage selector at the back side, be
the AC power cord.
sure
to set it to your local power
supplied
before
connecting
the CLOCK
Setting
1
Press CLOCK.
(If
the clock
requires setting, press
CLOCK for more than 2 seconds.)
The hours begin to flash.
and hold
4
Use PRESET
5
Press SET.
6
Use PRESET
-
2
Select
24 hour
a
pressing
cycle or
(-)/(+).
(12HR)
3
cycle by
or
(24HR)
Press SET to confirm the selected hour
Sleep
When the
1
12 hour
PRESET
cycle.
sleep
timer is used, the power is
(-)/(+)
to set the correct minutes.
Press SET and the correct time is shown
7
the
8
Press CLOCK at any time to
for about 3 seconds.
on
display.
display
the time
automatically
specify the time delay before the power is
turned off, press SLEEP.
In the display window you can see
for
about 5 seconds. This means that the system
turns off automatically after 90 minutes.
turned off after the
specified
time has
elapsed.
To
Each time the button is
pressed the time interval
by 10 minutes. i.e.
80...70... etc.
Select the desired time to turn off.
To check the
remaining
time until the power is
turned off.
While the
sleep function is active
briefly. The time remaining until it
displayed for about 5 seconds.
8
to set the correct hours.
Function
before it turns off is reduced
2
(-)/(+)
press SLEEP
turns off is
Note
If you press SLEEP while the
the SLEEP time is reset.
To cancel the
sleep
sleep
time is
displayed,
timer mode
If you wish to stop the function, press the SLEEP button
repeatedly until 10 appears, and then press SLEEP
once again while 10 is displayed.
Timer Function
With the TIMER function you can have the radio reception and
and recording turned on and off at the time desired.
1
2
Press CLOCK to check the current time.
Press "TIMER" to enter the timer
setting
9
mode.
you want to correct the previous memorized
TIMER setting, press and hold the "TIMER" button
(If
than 2 seconds.)
previous memorized timer on time and
"TIMER" appears in the display. Each function :
TUNER-CD-TAPE flashes in the display window
more
The
in
turn.
Press SET when the desired function is
3
flashing.
4
If you select the TUNER:
PLAY and REC flash in the
alternately
display
window
operating mode.
recording and play
TUNER play only
If you have selected the CD
4.
or
PRESET
?
7
8
11
Press SET.
12
Set the minute to switch off
13
Press SET.
14
Adjust
PRESET
PRESET
source
play
on.
BEFORPATIN
display.
by pressing
(-)/(+).
by pressing
(-)/(+).
the volume level
PRESET
by pressing
(-)/(+).
Press SET.
"TIMER" appears in the display window and the
timer setting has been completed.
Switch the system off.
16
(-)/(+)
and press SET. The hour "ON"
flashes.
The selected function is
switched
To cancel
Set the hour to switch
or
TAPE,
automatically
and off at the time set.
check the timer
select the timer set
timer
on
by pressing
PRESET
(-)/(+).
Press SET to confirm the hour to switch
The minute "ON"
or
on
Each time the "TIMER" button is
If you have selected the CD
ignore step 5.
display
setting
on.
or
cancel. You
pressed
can
you can
also check the
status.
check the timer, press the "TIMER" button
"TIMER" appears in the display window.
To cancel the TIMER, press the "TIMER" button so that
"TIMER" disappears in the display window.
so
or
that
flashes.
Set the minute to switch
PRESET
flashes in the
Set the hour to switch off
To activate
6
now
10
When you have selected the TUNER;
Select the previous memorized preset number with
display
auxiliary
TAPE,
ignore step
5
or
Press SET to confirm the minute to switch
The hour "OFF"
15
REC: TUNER
PLAY:
play, tape play
for about 3 seconds. Press SET to
confirm the desired
?
CD
recording,
on
by pressing
(-)/(+).
9
Audio
Volume
?
?
Adjustment
(-)/(+)
sound level,
counterclockwise to decrease it.
or
sound level,
Sound
or
(
)
the
to increase the
press the VOLUME CONTROL
the remote control.
(
)
on
Select
(EQ:
answer
display
SURROUND
impressions.
desired sound mode
:
ROCK
: more
POP
:
CLASSIC
:
Headphone
Connect
by using the EQ.PATT
control) button.
frequency response
linear
bass,
more
can
Select
choose between 3 fixed sound
desired surround mode
a
impressions.
by using SURROUND.
SURROUND 1 ON→ SURROUND 2 ON→ SURROUND OFF
treble
less bass, less treble
for orchestral music
XDSS (Extreme
a
Socket
stereo
Auxiliary
Connect
an
Dynamic Sound System)
Press XDSS to reinforce treble, bass and surround
effect.
headphone plug ( 3.5mm)
headphone jack.
The speakers are automatically disconnected
you plug in the headphones (not supplied).
into the
when
The "XDSS ON"
or
"XDSS OFF" indicator
To cancel it press XDSS
lights
up.
again.
Function
auxiliary
device i.e. TV
or
VCR, via the
rear
mounted AUX
phone
sockets.
Press AUX.
Note
You
can
also record from the
Recording
10
to
the remote
FLAT
1
2
example,
"MUTE" indicator flashes in the
window.
You
choose between 4 fixed sound
a
on
telephone,
To activate surround mode
Quality Adjustment
can
Press MUTE to mute your unit.
can mute your unit in order, for
You
To activate stereo sound
You
?
knob clockwise to increase the
Press VOLUME CONTROL
to decrease it
?
MUTE
Adjustment
Tu r n VOLUME
Section.
auxiliary input
source,
see
the radio stations
Presetting
You
can
preset 30 stations for FM and AM. Before
make
sure
Press FUNCTION
1
indicator
(or
in the
display
or
AM you want
window.
time you press BAND, FM and AM
Every
alternately.
frequency
(-)/(+)
on
changes
the front
indication starts to
panel until
change, then
the
release.
Scanning stops
when the unit tunes in
a
station.
in
automatically
Press
TUNING(-)/(+) for more
Tuning in manually
Press
4
TUNING(-)/(+) briefly
and
PROG./MEMORY(or
remote control).
Listening
repeatedly.
PROGRAM
Press and hold PROG./MEMORY
stations
are
display
window.
repeatedly to appear TUNER
(or TUNER/BAND on the remote
and then press BAND to select the FM
AM you want in the display window.
The last received station is tuned in.
PRESET
(-)/(+) (or
control) repeatedly
preset station you
-
presets
Press and hold PRESET
PRESET
(
)
control)
until the desired preset number
or
press it
repeatedly.
appears
on
To turn off the radio
Press POWER to turn the unit off
function mode
(
)
on
(CD,
TAPE
For your reference
If an FM program is
Press MODE/RIF
to select the
by rotating
KNOB (or pressing VOLUME (
remote control) repeatedly.
VOLUME
)
(-)/(+)
on
select another
or
AUX).
noisy
"STEREO" disappears
that
in
display window. There will be no stereo effect,
but the reception will improve. Press MODE/RIF
again to restore the stereo effect.
Each time you press the button, the unit tunes in
preset station at a time.
the volume
so
or
the
want.
?
3
(-)/(+) (or
the remote
one
Adjust
for
panel
cleared.
?
Press PRESET
the remote
the front
to the radio
control)
2
on
preset number will flash. To change the preset number,
To recall
the
on
Press FUNCTION
or
3 to 6 to store other stations.
follow the steps 5-6.
Press
indicator
the
about two seconds, "CLEAR" appears in the display
window and then press PROG./ MEMORY again, the
a
than 0.5 seconds.
A preset number will flash in the
1
on
The station is stored.
Repeat steps
7
PROGRAM
(or
control) again.
For your reference
If all stations have already been entered, FULL message
will appear in the display window for a moment and then
Notes
Tuning
remote
To clear all the memorized stations
Press TUNING
3
Press PROG./MEMORY
6
-
Press BAND to select the FM
(-)/(+) (or PRESET (
) on
control) to select the preset number
the remote
you want.
to appear TUNER
TUNER/BAND on the remote
repeatedly
control).
2
Press PRESET
5
that you have turned down the
volume to the minimum.
tuning,
To
improve reception
Reposition the supplied
antennas.
the
Notes
To listen to
?
?
Use manual
non-preset radio stations
or
For automatic
on
the front
automatic
tuning,
panel.
in step 2.
press and hold TUNING
tuning
(-)/(+)
Use MODE/RIF
function to
switch to
is distorted
by
mono
(Radio Interference Filter)
reception if stereo reception
noise.
When
recording
noises may
the
occur.
MW(AM)
or
LW broadcast, beat
If it does, press MODE/RIF
once.
11
OPERATION
Tape Playback
You
can use
Basic
1
2
3
normal tape.
only
To
Playback
Press FUNCTION
repeatedly
TAPE" appears in the
Open
cassette deck
PUSH EJECT
Insert
a
the
display window.)
4
To
Stop Play
(
or
:
plays only
front side, the unit stops
automatically.
tape side
to the bot-
AUTO REVERSE DECK:OPTIONAL
You
can
pressing
OPTIONAL).
select direction of the cassette you want
PLAY MODE.
STOP(
Press COUNTER
Playing
After the cassette
plays front or reverse
(backward play) side, stops automatically.
Once
) during playback.
Tape Counter
Reset
After the cassette
Twice
during playback.
0000" in display
time appears "TP
-
reverse
window.
by
Function
Pressing Display
Press
Fast Forward
the front
you want.
After auto stop deck
tom and then close deck.
Press PLAY
point
or
panel or the
during playback, press PLAY ( ) at
on
/
AUTO STOP DECK
by pushing
position.
cassette with the
Fast Rewind
pressing
remote control
indicator.
("NO
Play
After
to appear TAPE
front and
plays
side, stops automatically.
After the cassette
plays six times
repeatedly front and reverse side,
stops automatically.
Three
times
Recording
Wind the tape to the
Basic
1
2
point recording
(Use only
normal
Setting
TUNER
Open
tapes.)
To pause
Press FUNCTION
or
starts.
repeatedly
to appear the CD
Press
"
the cassette deck and insert
a
blank
compartment.
recording direction :OPTIONAL
Press PLAY MODE repeatedly to set the
recording direction.
or
REC" flashes in
indicator.
cassette into the cassette
recording
REC
To
again.
display window.
stop recording
Press TAPE
STOP(
).
To set the
from Radio, CD
Recording
or
Auxiliary
CD to
synchro recording function dubs
programmed titles automatically into
a
complete
and
a
cassette.
source
1
Press
REC
control),
and
on the remote
(or
then play the CD or TUNER
function.
"
REC" flashes and holds the cassette in pause
mode.
2
Press
REC
or PLAY(
) (or
PLAY( ) on the remote control).
The recording begins.
or
Tape Synchronized Recording
The CD
Press CD SYNC. in
1
"
REC" flashes and
display
stop mode.
""
displays
in the
window.
The synchronized recording is started
automatically after about 8 seconds.
2
Notes
If you wish to record from the desired track, select the
desired track with SKIP
ing
CD
/
before
commenc-
synchro recording.
The function change is not possible during
recording.
12
CD
CD
Playback
Basic
To cancel
Playback
Press FUNCTION
1
repeatedly
to appear CD
Repeat
-
indicator.
If
disc is loaded then "NO DISC" is
no
Press CD
2
disc
OPEN(
)
and
place
displayed.
the disc into the
tray.
an
8cm(3 inch) disc, put
Program Play
You
can
Press CD OPEN(
compartment.
4
PressPLAY(
)
Press PROG./MEMORY
1
it onto the inner circle
remote
)orPLAY/PAUSE(
)onthe
remote control.
To Pause
Play
(CD ) or PLAY/ PAUSE (
control during playback.
Press this button
To
again
it to
resume
)
To
?
) button
(
(
) button is pressed once
midway through a track, the player returns to the
start of that track. When it is pressed again, a
track is skipped each time the button is pressed.
After
Fast Rewind
pressing
remote control
the
To
To
point
on
or
Fast Forward
the front
panel
during playback, press
one
track
once
PROGRAM
PLAY/ PAUSE
(
on
)
on
the
the
PROGRAM
(or
on
the remote
on
or
PLAY
(
the
)
at
on
displayed.
repeatedly
(or
PROGRAM
on
the remote
the stop mode. And then press CLEAR
panel
1.
or
STOP(
)
on
on
the remote control.
Press PROG./MEMORY
remote
(or PROGRAM on the
control) repeatedly on the program stop
mode until "Track Number" blinks.
2.
Repeat
To
modify program
1.
Press the PROG./MEMORY
2.
control)
to modify.
Repeat 2~4.
remote
Repeat Play
play
the
To add program contents
you want.
Press REPEAT
-
/
(or
the stop mode.
A track and program number will be
the front
Play
PLAY( ) (or
control).
PROG./MEMORY
control)
When the SKIP
To
on
to select the track.
)
Press PROG./MEMORY
to go to the next
track.
?
PROGRAM
To clear program contents
the Track
Press the SKIP
contain up
remote
Press
) during playback.
Skipping
1~3.
control)
-
STOP(
Repeat
the discs and
To check program contents
play.
Stop Play
Press
control).
(or
on
can
the stop mode.
on
/
SKIP(
remote
Press
5
on
control)
Press PROG./MEMORY
3
4
Press CD PAUSE
the remote
Press
2
to close the disc
arrange the order of the tracks
create your own program. The program
to 20 tracks.
of the tray.
3
during playback.
disappears.
once more
indicator
To
Note
To load
repeat play
Press REPEAT
2~5.
to
contents
display
(or
PROGRAM
on
the
program number you want
during playback.
display.
"REPEAT 1" appears in the
To
play
all tracks
repeatedly
Press REPEAT
-
"REPEAT
again during playback.
ALL" appears in the display.
13
OPERATION
Troubleshooting
Check the
following guide
for the
possible
of
a
?
?
The power cord is disconnected.
The audio cables
connected
?
?
not
are
?
securely.
Digital
Audio
to the wrong
service.
Plug
the power cord into the wall
securely.
Connect the audio cable into the
jacks securely.
The power of the external
equipment is switched off.
The
contacting
Correction
?
outlet
No sound.
before
problem
Cause
Symptom
No power.
cause
Output
position.
source
?
Switch
the external
on
source
equipment.
is set
?
Set the
Digital Audio Output to
position, then turn on
again by pressing
the correct
the unit
POWER.
The unit does not
start
?
No disc is inserted.
?
Insert
a
disc.
?
An
?
Insert
a
playable
?
The disc is
playback.
disc is inserted.
unplayable
placed upside
down.
?
disc.
Place the disc with the
playback
side down.
?
The disc is not
placed
within the
?
The remote control
?
The disc is
?
The remote control is not
does not work
properly.
dirty.
at the remote
?
sensor
pointed
There is
an
obstacle in the
tray
guide.
?
Point the remote control at the
remote
?
sensor
Operate
of the unit.
the remote control
within about 23 ft
path
the disc
Clean the disc.
of the unit.
The remote control is too far
on
inside the
?
from the unit.
?
Place the disc
correctly
guide.
?
(7 m).
Remove the obstacle.
of the remote control and the
unit.
?
The batteries in the remote
control
14
are
exhausted.
?
Replace
ones.
the batteries with
new
Specifications
MODEL
SECTION
[Genral]
Power
supply
Power
consumption
External dimensions
[CD]
FM
[Tuner]
(MW)
(WxHxD)
50W
4.50kg
60 dB
70 dB
70 dB
60 dB
70 dB
70 dB
10.7 MHz
-
to Noise Ratio
55/50 dB
60/55 dB
60
Tuning Range
522-1611kHzOR530-1610kHz
Intermediate
450 kHz
Frequency
Signal
-
35 dB
100
-
1800 Hz
Power
5W
T.H.D
15W
0.5%
ratio
Tape Speed
Wow Flutter
0.25%
F.F/REW Time
120sec
Frequency Response
250
to Noise Ratio
Signal
55dB
Type
Power
specifications
are
subject
to
change
Speaker
FE-196E
2
Way
2
Speaker
4Ω
6Ω
75-20000Hz
70-20000Hz
(1m)
30W
150x254x171mm
1.56kg
Way
1
15W
10W
(WxHxD)
1
86 dB/W
(1m)
5W
Weight (1EA)
and
FE-195E
Speaker
86 dB/W
Power
Net Dimensions
Designs
1
90-20000Hz
Sound Pressure Level
Net
(MTT-5511)
4Ω
Frequency Response
Input
(C-60)
8000Hz
Way
Impedance
Max.
80 dB
(MTT -111, JIS-WTD)
FE-192E
name
Input
80 dB
50dB(P/B)/45dB(R/P)
1
Rated
42-25000Hz
43dB
Separation
Erase Ratio
Model
-
0.15%
42-25000Hz
60 dB
4.75cm/sec
25W
0.15%
60-20000Hz
Frequency Response
Signal-to-noise
60/55 dB
10000 Hz
Frequency Response
to Noise Ratio
REF NC
108.0 MHz
Intermediate
Channel
[Speakrs]
40W
4.35kg
Tuning Range
Output
[TAPE]
30W
18000 Hz
range
Frequency Response
[Amp]
-
ratio
Frequency
of the unit.
3.50kg
87.5
Signal
panel
FFH-196A
161 X 254 X 249.5mm
40
response
Signal-to-noise
Dynamic
FFH-195A
Refer to the back
Mass
Frequency
AM
FFH-192A
150x254x191mm
1.80kg
87 dB/W
(1m)
25W
50W
150x254x197mm
1.96kg
without notice.
15
P/NO :3828R-A056E
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising