advertisement
▼
Scroll to page 2
of 38
DVD Player+ Video Cassette Recorder OWNER'S MANUAL MODEL : V-781M Before connecting, operating please read this instruction booklet or adjusting this product, carefully and completely. Safety Precautions CAUTION: The apparatus should not be exposed to water (dripping or splashing) and no objects filled with liquids, such CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN as placed on the apparatus. equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER vases, should be FCC WARNING: This (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. REGULATORY INFORMATION: FCC Part 15 product has been tested and found to comply with the a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the product is operated in a residential installation. This product generates, uses, and can radiate radio frequency energy and, if not This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric This shock to persons. The exclamation point is intended to alert the within user an equilateral triangle to the presence of installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is in important operating and maintenance (servicing) instructions in the literature accompanying the product. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. no guarantee that interference will particular installation. not occur If this product does cause harmful interference to radio or television reception, which can be determined by turning the product off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the product and a receiver. CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. ATTENTION: POUR EVITER LES CHOC limits for ELECTRIQUES, Connect the product into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer for or an experienced radio/TV technician help. INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU'AU FOND. WARNING: Do not install this equipment in such as a book case or similar unit. a confined space NOTE TO CABLE/TV INSTALLER: This reminder is provided to call the cable TV system installer 's attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical. CAUTION: This DVD+VCR To manual use require maintenance, a Laser of this read this owner's unit contact an authorized service location. ardous radiation exposure. To prevent direct exposure to laser beam, do not try to open the enclosure. Visible laser radiation when open. DO NOT STARE INTO BEAM. on the back of this unit. This number is System. Use of controls, adjustments, or the performance of procedures other than those specified herein may result in haz- 2 by law to copy, broadcast, show, broadcast play in public, or rent copyrighted material without permission. This product uses copyright protection developed by Macrovision. Copy protection signals are recorded on some discs. When recording and playing the pictures of these discs on a VCR, picture noise will appear. This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited. via cable, SERIAL NUMBER: The serial number is found employs proper product, please carefully and retain for future reference should the ensure OTES ON COPYRIGHTS: It is forbidden unique to this unit and not available others. You should record requested information here and retain this guide as a permanent record of your purchase. Model No. Serial No. _________________________________ to IMPORTANT SAFETY INSTRUCTIONS CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS IN THIS OWNER'S MANUAL. AND THOSE MARKED ON THE PRODUCT. RETAIN THIS BOOKLET FOR FUTURE REFERENCE. designed and manufactured to assure personal safety. Improper use can result in electric safeguards incorporated in this product will protect you if you observe the following procedures for installation, use, and servicing. This product does not contain any parts that can be repaired by the user. This product shock has been fire hazard. The or DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY. 1. Read these instructions. - All these safety instructions should be read before the ating operated. 2. these instructions. Keep use The - and operis 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the product. product safety, operating and instructions should be retained for future refer- 11. Only use attachments/accessories specified by the manufacturer. ence. warnings. All warnings on the product and operating instructions should be adhered to. 3. Heed all in the 4. Follow - all instructions. - All operating and use instructions should be followed. 5. Do not use this near a in wet a other product near water. For example: laundry tub, swimming pool; and -- bath tub, wash bowl, kitchen sink, basement; areas located or near near a water. 12. Use only with the cart, stand, tripod, bracket, or specified by the manufacturer, or sold with table 6. Clean only with dry cloth. the wall outlet before Unplug this product from cleaning. Do not use liquid apparatus. When -- when cleaners. avoid 7. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. - Slots and as a ensure reliable bookcase vided or or rack unless proper ventilation is prothe manufacturer's instructions have been adhered to. 8. Do not install near any heat sources ators, heat registers, stoves, (including amplifiers) such as cart is used, use caution combination to Unplug this product during lightning storms long periods of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the product has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the product, the product has been exposed to rain or moisture, does not operate normally, or has been dropped. radi- other apparatus that produce heat. or 9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement or when unused for in the cabinet are provided for operation of the product and to protect it from over- heating. The openings should never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product should not be placed in a built-in installation such openings ventilation and to 13. a moving the cart/product injury from tip-over. of the obsolete outlet. 3 INTRODUC Table of Contents Introduction SafetyPrecautions.........................2 IMPORTANTSAFETYINSTRUCTIONS. .3 TableofContents..........................4 BeforeUse..............................5-6 . . . . . . . . PlayableDiscs...........................5 3DSurround........................27 Zoom..............................28 MarkerSearch.......................28 SpecialDVDFeatures....................28 Checking the contents of DVD Video discs: Menus 28 . TitleMenu..........................28 Precautions.............................6 DiscMenu..........................28 NotesonDiscs..........................6 CameraAngle.......................28 .28 ChangingtheAudioLanguage. .28 ChangingtheAudioChannel. AboutSymbols..........................6 SelectingtheViewingSource................6 . . . . . . . . . . . . . . . . . . . FrontPanelControls........................7 Subtitles............................28 DisplayWindow............................8 LastconditionMemory.................28 Operation with Audio CD and MP3/WMA Disc 29-30 29 Playing an Audio CD and MP3/WMA Disc .29 NotesonMP3/WMARecordings. RemoteControl............................9 ConnectionsPanel........................10 . Preparation . . . . . . . . . . . . . . Pause.............................30 Connections...........................11-13 11 Connecting Antenna/Cable TV to DVD+VCR . . . BasicTVConnections....................12 MovingtoanotherTrack...............30 RepeatTrack/All/Off..................30 Search.............................30 12-13 Optional, Preferred TV Connections BeforeVCROperation...................14-15 On-ScreenDisplay(OSD)..................14 Random...........................30 Howtousethemainmenu................14 ChannelSelection.......................15 .30 ChangingtheAudioChannel. OperationwithJPEGDisc...................31 ViewingaJPEGdisc.....................31 MovingtoanotherFile.................31 . . . . . . . SettingtheClock........................15 BeforeDVDOperation...................16-19 GeneralExplanation......................16 On-ScreenDisplay.......................16 InitialSettings........................17-19 GeneralOperation....................17 Language..........................17 Picture.............................17 Sound.............................18 Others.............................18 ParentalControl......................19 Operation TapeOperation.........................20-25 NormalPlayback........................20 SpecialEffectPlaybacks..................20 Search.............................20 Still Picture and Frame-by-Frame Playback . 20 SlowMotion.........................20 .20 CMSkip(CommercialSkip). EZ(EASY)Repeat....................20 NormalRecording.......................21 TimerRecording......................21-22 InstantTimerRecording...................22 DubbingandEditing......................23 CopyingfromDVDtoVCR.................23 VHS Hi-Fi Stereo System/MTS Broadcast 23-24 .24 TapeCounterMemoryFeature. . . . . . . . . . . . . . . . . . . . . . RepeatA-B.........................30 3DSurround........................30 . . . . . . . . . . . . . . . . . . . StillPicture.........................31 Toflipthepicture.....................31 Torotatepicture......................31 .31 NotesonJPEGRecordings. ProgrammedPlayback.....................32 Programmed Playback with Audio CD and . . . . . . . . . . . MP3/WMADisc.........................32 .32 ProgrammedPlaybackwithVideoCD. . . . . . . . . . . . . . . . . . . . . . . . RepeatProgrammedTracks ErasingaTrackfromProgramList. ErasingtheCompleteProgramList. . . . . . . . . Reference About the symbols Indicates hazards itself or for instructions harm to the unit likely to cause damage. other material Indicates special operating Indicates tips features of this unit. and hints for making the task easier. . MovingtoanotherTITLE...............26 26 Moving to another CHAPTER/TRACK . . . . Manufactured under license from Dolby Laboratories. "Dolby", "Pro Logic", and the double-D symbol are trademarks of Dolby Laboratories. SlowMotion.........................26 Frame-by-Frame Playback . 27 Search.............................27 Random............................27 Repeat.............................27 RepeatA-B.........................27 TimeSearch........................27 4 .32 . GeneralFeatures........................26 Still Picture and .32 . PlayingDVDsandVideoCD...............26 . .32 Troubleshooting........................33-34 LanguageCodeList.......................35 CountryCodeList.........................36 Specifications............................37 AdditionalInformation....................25 .26-28 DVDandVideoCDOperation . . DTS and DTS Systems, Inc. Digital Out are trademarks of Digital Theater Before Use Playable Disc-related Terms Discs Title (8 (DVD only) The main film content DVD cm/12 cm or disc) Each title is Video CD (VCD) (8cm/12cmdisc) cm/12 cm disc) In addition, this unit can play a SVCD, Kodak PICTURE CD, and CD-R/RW, DVD-R/±RW that contains audio titles, MP3, JPEG or WMA files. otes -- Track -- Depending on the conditions of the recording equipment or the CD-R/RW (or DVD-R/±RW) disc itself, some CD-R/RW (or DVD-R/±RW) discs cannot be played on the unit. The unit cannot play discs that contain data other Do not attach any seal or label to either side (the labeled side or the recorded side) of a disc. use irregularly shaped CDs (e.g., heart-shaped or octagonal). The a title reference number (Video a enabling CD and audio CD picture or a only) piece assigned musical audio CD. Each track is or an than MP3 and CD-DA data. -- assigned easily. Chapter (DVD only) Sections of a picture or a musical piece that are smaller than titles. A title is composed of one or several chapters. Each chapter is assigned a chapter number to enable you to locate the chapter you want. Depending on the disc, chapters may not be recorded. Sections of -- feature content you to locate it Audio CD (8 accompanying or music album. on a video CD track number, a you to locate the track you want. enabling Scene On video CD with PBC (Playback control) functions, pictures are divided into sections called "Scenes". Each scene is displayed in the menu screen and assigned a scene number, enabling a and still moving pictures you to locate the scene you want. A scene is composed of one or several tracks. Do not unit may Types malfunction. There of video CDs are two types of video CDs: equipped with PBC (Version 2.0) (Playback control) functions allow you to interact Video CDs PBC otes on DVDs and Video CDs Some playback operations with the of DVDs and Video CDs may be intentionally fixed by software manufacturers. As this unit plays DVDs and Video CDs according to disc content some designed by the software manufacturer, playback features of the unit may not be available other functions may be added. Refer also to the instructions supplied with the DVDs or and Video CDs. Some DVDs made for business purposes may not be played on the unit. Regional code of this DVD+VCR and DVDs This DVD+VCR is and manufactured 4 designed playback of Region 4 encoded DVD software. The region code on the labels of some DVD discs indicate which type of DVD+VCR can play those discs. This unit can play only DVD discs labeled 4 or ALL. If you try to play any other discs, the message "Check Regional system via back is prohibited by area limits. functions, Video CDs not playing DTS-encoded CDs, excessive noise may analog stereo output. To avoid possible damage to the audio system, turn down the volume before playing back such discs, adjust the volume gradually, and keep the volume level low. To enjoy DTS Digital SurroundTM playback, an external 5.1 channel Digital SurroundTM decoder system must be connected to the digital output of the unit. When be exhibited from the other pictures included in equipped with PBC (Version 1.1) Operated way as audio CDs, these discs allow playback of video pictures as well as sound, but they are not equipped with PBC. in the same Remote Control Battery Detach the battery cover on the rear of the control, and insert two R03 (size remote AAA AAA Installation AAA) batteries correctly. with and aligned Caution Do not mix old and new batteries. Never mix different types of batteries (standard, alkaline, etc.). Remote Control Operating Range Point the remote control at the remote ote on DTS-encoded CDs or still the disc. for Code" will appear on the TV screen. Some DVD discs may not have a region code label even though their play- menus, search typical computer-like operations. Moreover, of high resolution can be played if they are sensor and press the buttons. Distance: About 23 ft (7 m) from the front of the remote sensor Angle: About 30° in each direction of the front of the remote sensor 5 INTRODUC Before Use (Continued) Cleaning Precautions the unit Handling discs Fingerprints and dust on the disc can cause poor picquality and sound distortion. Before playing, clean the disc with a clean cloth. Wipe the disc from the centure shipping the unit original shipping carton and packing materials come in handy. For maximum protection, re-pack the unit as it was originally packaged at the factory. When The ter out. setting up the unit picture and sound of a nearby TV, VCR, or radio may be distorted during playback. In this case, position When Yes The the unit away from the TV, VCR, unit after removing the disc. To keep Do not near or radio, turn off the or the surface clean use volatile liquids, such as contact with the unit for a leave marks on insecticide spray, plastic products in long period of time. They will the unit. Do not leave rubber or the surface. the unit Cleaning a soft cloth use a lightly benzine, use thinner, or spray intended for older About " soft, dry cloth. If the surfaces solution. Do not Do not use strong solvents such as alcohol, benzine, thinner, commercially available cleaners, or anti-static are moistened with a extremely dirty, mild detergent strong solvents such as these as might damage the surface may appear on the TV This icon means the function manual is not available About the disc a clear The DVD+VCR is picture high-tech, precision a applicable only device. If the DVD optical pick-up lens and disc drive parts are dirty or worn, the picture quality will be poor. Regular inspection and maintenance are recommended after every 1,000 hours of use. (This depends on the operating environment.) For details, please contact your nearest dealer. Notes on Handling VCD2.0 for instructions of the following symbols are represented by the symbol. DVDs Video CDs with the PBC (playback control) VCD1.1 Video CDs without the PBC (playback control) function. CD Discs Audio CDs. MP3 MP3 Discs. WMA WMA Discs. JPEG JPEG Discs. discs Hold the disc on one to those discs screen function. playback side of the disc. by the edges so that fingerprints Selecting Do not touch the get on during operation. explained in this owner's that specific DVD video disc. symbols Asection whose title has To obtain records. symbol display " alcohol, of the unit. vinyl Symbols About the To clean the cabinet Use No You must select will not VCR) the surface. Do not stick paper or tape on the the disc. Viewing Source one of your output sources (DVD or to view on the TV screen. If you want to view DVD deck output source: Press DVD on the remote or DVD/VCR on the front ? until DVD indicator in the source panel display window lights and output of DVD deck is viewed on the TV screen. If you want to view VCR deck output source: Press VCR on the remote or DVD/VCR on the front ? until VCR indicator in the Storing After discs playing, of VCR deck is viewed on the TV screen. store the disc in its case. Do not expose the disc to direct sunlight or sources of heat, or leave it in a parked car exposed to direct sun- light, as there may be a considerable temperature increase inside the car. 6 source panel display window lights and output ? otes If you insert a disc while the DVD+VCR is in the VCR mode, the DVD+VCR will switch to DVD mode automatically. ? If you insert a cassette tape without prevention tab while the DVD+VCR is in the DVD mode, the DVD+VCR will switch to VCR mode automatically. Front Panel Controls EJECT(Z) Ejects the tape in the VCR deck. PLAY To back play a recorded tape Cassette COPY Insert Press to copy a DVD in the DVD deck to a VHS tape in a disc a REC/ITR Disc Tray (DVD deck) Insert a To record disc here. normally or or INTRODUC (x) tape. (z) to activate Instant Timer Recording. DVD/VCR (output select) Select one of your output sources to view on the TV screen between DVD and VCR. Enter Acknowledges Compartment (VCR deck) STOP of (B) disc. video cassette here. the VCR deck. Stops playback or menu selection. Remote Sensor Point the DVD+VCR remote control here. Display window Shows the current status of the DVD+VCR. OPEN/CLOSE (Z) or closes the disc tray. Opens b/B/v/V - - Selects CH To (left/right/up/down) an option in the menu. (v/V) scan up or down through memorized channels. Reverse SKIP/SCAN (S/Q) beginning of current chapter/track previous chapter/track. Press and hold for DVD: Go to or LINE 2 (VIDEO IN/AUDIO (Left/Right)) a fast reverse search. VCR: Rewinds the tape during the STOP mode or for fast reverse picture search. IN Forward SKIP/SCAN (R/T) DVD: Go to NEXT chapter/track. Press and hold Connect the audio/video output of an external source for two seconds for a fast forward search. VCR: Advances the tape during the STOP mode or for fast forward picture search. (Audio system, TV/Monitor, VCR). Another POWER Switches the DVD+VCR ON and OFF. to PAUSE/STEP(X/C) playback of a tape or a disc in the DVD or VCR deck temporarily/press repeatedly for frame-by-frame playback. Pause 7 Display Window VCR DVD+VCR functions are are available and channels selected at DVD+VCR. MP3 MP3 Disc inserted. RPT Indicates repeat mode. ALL Indicates A y B repeat all mode. Indicates A-B repeat mode. PROG Programmed playback TITLE active. Indicates current title number. CHP/TRK Indicates current chapter or track number. A disc is in the DVD deck. SAP Indicates when broadcast is being a SAP BILINGUAL received. STEREO Indicates is being a stereo broadcast received. COPY DVD to VCR copy is in progress. DVD DVD inserted. CD Audio CD inserted. VCD Video CD inserted PHOTO JPEG Disc inserted WMA WMA Disc inserted Lights when TV mode is active. Indicates clock, total playing time, elapsed time, remaining time, chapter number, track number, channel or current deck status (Playback, Pause, etc). REC DVD+VCR is HI-FI Indicates the unit is playing back a Recording. tape recorded in Hi-Fi. DVD+VCR is in timer recording or a timer recording is programmed. A cassette is in the VCR deck. 8 Remote Control DVD/VCR select button OPEN/CLOSE, EJECT (Z) Select the output source (DVD or VCR) to view on the TV screen. - - POWER SELECT/ENTER Switches DVD+VCR ON and OFF. - - TV/VCR by the tuner or TV tuner. To select the VCR deck's (Tuner, DISPLAY, CLK/CNT Accesses On-Screen - Accesses option an in the FORWARD DVD: Search chapter setup and VCR source 2). DVD disc. menu. (>) forward*/go to next track. or VCR: Advances the tape in STOP mode or for fast forward picture search. SETUP, MENU DVD menu on a Removes the setup onscreen. or removes LINE menu -CH/TRK v/V: Selects channel of VCR. Adjusts manually the tape's picture Accesses or RETURN (left/right/up/down) Selects LINE 1, DISC MENU display. Switches among the clock, tape counter and tape remaining modes on the display. b/B/v/V Acknowledges menu selection. Displays functions on the TV screen. INPUT by the VCR To view channels selected Opens and closes the disc tray. Ejects the tape in the VCR deck. menu *Press and hold button for about two menu. seconds. TITLE Displays the disc's Title PLAY menu, if Starts available. PAUSE/STEP BACKWARD (X) backward*/go to beginning of current chapter or track or go to previous chapter or track. playback or recording temporarily/press repeatedly for frameby-frame playback. VCR: Rewinds the tape in STOP mode or for fast reverse picture search. (x) Stops playback. REC/ITR Records normally or *Press and hold button for about two seconds. (z) activates Instant Timer PROGRAM Recording. Accesses 0-9 numerical buttons Selects numbered options in an audio language (DVD) or an audio channel (CD). a subtitle Removes menu. a track number on the ANGLE Selects a DVD camera angle if available. language. ZOOM MARKER Marks any Program program menu or a mark on the MARKER SEARCH menu. SUBTITLE Selects or removes CLEAR a menu. AUDIO Selects (.) DVD: Search Pause STOP (H) playback. Enlarges point during playback. DVD video image. SEARCH Displays MARKER SEARCH REPEAT, ez menu. REPEAT Repeat chapter, track, title, all. Replays the specified segment twice. RANDOM, CM SKIP Plays tracks in random order. Fast forwards picture search through 30 seconds of recording. - - A-B, SPEED Repeats sequence. Selects recording speed - - ote This remote control functions To use To use use the same buttons for VCR and DVD (ex. PLAY). the VCR, first press the VCR button. the DVD, first press the DVD button. 9 INTRODUC Connections Panel S-VIDEO OUT Connect to a (DVD OUT) Input S-Video on TV. VCR IN LINE 1 (VIDEO IN/AUDIO IN (Left/Right)) Connect the audio/video output of an external (Audio system, TV/Monitor, another VCR). DVD/VCR OUT Connect to a source (VIDEO/AUDIO (Left/Right)) inputs. TV with video and audio COMPONENT VIDEO OUT Connect to a (Y Pb Pr) (DVD OUT) inputs. TV with Y Pb Pr AUDIO OUT Connect to a (Left/Right) (DVD OUT) TV, amplifier, receiver, or stereo system. AC Power Cord Plug into the power source. DIGITAL AUDIO OUT Connect to RF. (COAXIAL) (DVD OUT) digital (coaxial) audio equipment. OUT(DVD/VCR OUT) Connect to a TV with RF coaxial inputs. ANTENNA INPUT Connect the VHF/UHF/CATV antenna to this terminal. Do not touch the inner pins of the jacks on the rear panel. Electrostatic discharge may cause permanent damage to the unit. 10 Connections Without Cable Box ips If your cable wire is connected to your TV without a converter descrambler box, unscrew the wire from your TV and attach your TV and other equipment you wish to connect, there are various ways you could connect the DVD+VCR. Use connections described on pages 11-13. or Depending on it to the ANT.IN jack on Please refer to the manuals of your TV, VCR, Stereo or other devices as necessary to make the best jack and the System connection, you connections. hyperband channels. reproduction, connect the DVD+VCR's DVD/VCR AUDIO OUT jack to the audio in jacks of your amplifier, receiver, stereo or audio/video equipment. See "Optional, Preferred TV Connections" on pages 12-13. the DVD+VCR. Use the supplied round coaxial cable to connect between the DVD+VCR's RF.OUT 75 ohm antenna can input jack on the TV. With this receive all midband, super band, and For better sound With Cable Box If a converter is The cable Caution Make sure To view the DVD+VCR is connected Tune the TV to the correct video directly input channel. to the TV. to the phono in jack (record deck) of your audio system. hookup permits both or system, follow the TV and DVD+VCR operation. record CATV channel 1 Tune the TV to the DVD+VCR output channel (CH 3 or 4). output channel of the Cable Converter box by using the CH (v/V)or number (0-9) of your DVD+VCR. (Example: CH3) 3 Select the channel to view at the Cable Converter Box. Do not connect your DVD+VCR via your VCR. The DVD image could be distorted by the copy protection system. Connecting Antenna/Cable TV to otes With this connection, you CANNOT record viewing another. you are using a cable box to tune essary to do Auto Channel Set Disconnect the antenna leads from the rear one program while If DVD+VCR 1 in your cable 2 Set the DVD+VCR channel selector to the Do not connect the DVD+VCR's DVD/VCR AUDIO OUT jack required instruction below: as channels, it is indicated on not nec- page 15. of the TV. Cable TV the type of cable from your antenna. If it is round cable as illustrated, it is a 75 ohm coaxial 2 Identify a antenna cable. This cable will connect the jack marked ANT.IN on directly Wall Jack Back Panel of to Typical your DVD+VCR. Cable Box ip If your antenna lead wire is a flat type antenna cable, connect it to a Antenna Adaptor (300-ohm to 75-ohm) (not supplied) and slip the Adaptor onto the ANT.IN jack. The Adaptor does not screw on to the DVD+VCR, it just slips over the jack. Antenna Antenna Cable TV Wall Jack Flat Wire (300 ohm) Rear of DVD+VCR 300/75 ohm OR OR Adaptor (Not supplied) Rear of DVD+VCR 11 PREATION Connections (Continued) Basic TV Connections Make the of the one Optional, following connections, depending existing equipment. on of your capabilities otes You RF coaxial connection can through jack on the DVD+VCR to the jack on the TV using the 75-ohm Coaxial Cable supplied (R). Preferred TV Connections ONLY watch and listen to DVD playback the connections shown below. Connect the RF.OUT S-Video connection antenna in ote 2 How to set the DVD+VCR's RF output channel 1. While the DVD+VCR is turned off, press and hold CH (v/V) on the front the panel on "RF 04" appears in or display window. 2. Use CH (v/V) on the front the remote control to (CH 03 or CH 3. Turn off and panel change the or CH/TRK(v/V) RF on 4. Select TV CH to 3 or 4 depending on the RF jack the TV on the DVD+VCR using the optional Right AUDIO OUT jacks of left/right in jacks on the supplied audio cables (A2). using the Video (Color Stream ) connection Connect the COMPONENT VIDEO OUT 1 jacks on corresponding jacks on the optional Y Pb Pr cable (C). the DVD+VCR to the TV 2 the DVD+VCR. on Connect the Left and Component output channel 04). on jack (S). the DVD+VCR to the audio TV for about five seconds. and "RF 03" to the S-Video in S-Video cable If you use this connection, tune the TV to the DVD+VCR's RF output channel (CH 3 or 4). The unit will turn itself Connect the S-VIDEO OUT 1 using an in Connect the Left and Right AUDIO OUT jacks of left/right in jacks on the supplied audio cables. the DVD+VCR to the audio TV (A2) using the output channel you had selected. Now you can watch the DVD+VCR Channel 3 or 4. playback on TV Rear of TV Audio/Video connection Connect the DVD/VCR VIDEO OUT 1 DVD+VCR to the video in video cable jack on jack the TV on S-VIDEO the using INPUT COMPONENT VIDEO INPUT AUDIO INPUT the Pr supplied (V). Pb Y R Connect the Left and 2 jacks jacks Right DVD/VCR AUDIO OUT left/right in (A1) using the supplied audio on the DVD+VCR to the audio on the TV cables. S C ote If you use this connection, set the TV's to VIDEO. source selector Rear of TV ANTENNA INPUT AUDIO INPUT L VIDEO INPUT R Rear of DVD+VCR R A1 Rear of DVD+VCR 12 V A2 L Connections Optional, (Continued) Preferred TV Connections Rear of DVD+VCR ote playback using COAXIAL (A2) connections. The tuner and VCR will still be heard through the RF.OUT (R) or DVD/VCR AUDIO OUT (A1) jack. (See page 12.) You (X) can ONLY listen to DVD and AUDIO OUT PREATION Connecting to an amplifier equipped with two analog stereo or Dolby Surround channel Connect the Left and Right AUDIO OUT (or DVD/VCR A1 A2 X AUDIO OUT) jacks on the DVD+VCR to the audio left right in jacks on your amplifier, receiver, or stereo system using the audio cables (for A1 or A2 connection) supplied. and Connecting to an amplifier equipped with two digital stereo (PCM) or to an Audio/Video receiver equipped with a multi-channel decoder (Dolby DigitalTM, MPEG 2, or DTS) channel 1 Connect one R COAXIAL DIGITAL INPUT Amplifier (Receiver) of the DVD+VCR's DIGITAL AUDIO OUT jacks (COAXIAL X) to the corresponding jack on your amplifier. Use an optional digital (coaxial X) audio cable. You will need to activate the DVD+VCR's 2 output. (See "Digital Digital L AUDIO INPUT Audio Output" on Accessory Audio/Video (A/V) Connections in to DVD+VCR Connect the VCR IN LINE 1 or LINE 2 DVD+VCR to the audio/video out digital 18). accessory component, cables. page using the jacks on the jacks on your optional audio/video Multi-channel sound A digital multi-channel sound quality. For this connection provides the best you need a multi-channel Audio/Video receiver that supports one or more of the supported by your DVD+VCR (MPEG 2, Dolby Digital and DTS). Check the receiver manual and the logos on the front of the receiver. audio formats Jack Panel of Accessory AUDIO OUTPUT R L Caution: Due to the DTS will be in DTS Licensing agreement, the digital output digital out when DTS audio stream is VIDEO OUTPUT selected. otes -- If the audio format of the digital output does not match capabilities of your receiver, the receiver will produce a strong, distorted sound or no sound at all. Six Channel Digital Surround Sound via digital connection can only be obtained if your receiver is equipped with a Digital Multi-channel decoder. the -- --To see screen the audio format of the current DVD in the display, press AUDIO. OR on- Rear of DVD+VCR Front of DVD+VCR 13 Before VCR On-Screen Operation Some of these functions will be VCR is How to Display (OSD) displayed every time the operated. use This DVD+VCR menus The the main easily can displayed be menu programmed by using the on screen. controlled from the Remote Control menus are Handset. PLAY CH4 SP 1 STEREO Switch on your TV set and DVD+VCR button. by press- ing POWER Press MENU button. 2 The main JUL menu will appear on the TV screen. 2:15PM 5,SAT TAPE SPEED DISPLAY Shows the current tape speed. FUNCTION DISPLAY Indicates the function in progress. CHANNEL/HI-FI DISPLAY O Indicates the selected channel Indicates when this unit is (or LINE1, LINE2). playing back tape recorded ABC OSD To with change select the Hi-Fi Audio. the language setting for OSD. You can language among SPANISH, ENGLISH and PORTUGUESE. DATE DISPLAY Shows the current date. (Month/Date/Day TUNING SET of the week format) Manual CLOCK/COUNT DISPLAY TIME DATE Shows the current time and tape counter time on tuning setting (see Date and clock the tape. setting (see page 15). page 15). REC Timer Each press of the SELECT/ENTER changes the TV displays in the following sequence. on-screen STOP O To CH4 SP recording setting (see display the DVD+VCR STEREO O pages 21-22). fOSD ON/OFF operational mode (see left column). of your AUDIO SOUND Selecting the audio output signals from the AUDIO OUT (L ch and R ch), and RF.OUT. (see page terminals JUL 2:15 PM 5,SAT 23). 2:15 PM S O E 0:35:40 VIDEO DOCTOR Show the status of aspects of the DVD+VCR. (see O To set the otes The function screen displays be can displayed seen (or tape counter) mode the TV page To turn off the on screen 2 Select 3 Select OFF 4 Press MENU to using using only when a 3 the setting. on-screen function.(see BROADCAST TYPE Press 1 or 2 to page use select the desired Press SELECT/ENTER and press 5 when 23-24). menu. 3 or 4 select. b or B then press SELECT/ENTER. save Background 25). recording.(see menu. v or V. 25). To set the broadcast audio format to cassette is displays completely. Press MENU to enter the main O will continue until you press SELECT/ENTER. The tape counter indicator appear inserted. 14 on for 5 seconds. The clock 1 page BACKGROUND Press MENU to return to a TV picture. to Before VCR Operation (Continued) Channel Selection This DVD+VCR is synthesized tuner Setting equipped with a frequency capable of receiving up to 181 1 channels. These include VHF channels 2-13, UHF channels 14-69 and CATV channels 1-125. the Clock Press MENU and the MAIN Use b or B to select menu will appear. (TIME DATE) 2 SELECT/ENTERER. and press PREATION Preparation: Connect the DVD+VCR to the desired type of antenna or cable TV system, as shown in Connecting Antenna/Cable TV to DVD+VCR page 11. on DAT E ---/--/---- TIME --:-- --- -- Auto Channel Set 1 Press MENU and the MAIN menu will appear. Use b/B to select the (TUNING SET) 2 then press SELECT/ENTER. Use v/V choose the SEARCH option, then press 3 SELECT/ENTER. menu, 3UsethevorVtosetMONTHfirst. option. 4 DAY, by using Press B to And then set move to next v or V YEAR and TIME and B. to All available channels in your area are scanned and stored in the memory of the DVD+VCR. After scan- the ning, previous screen returns. otes The day of the week will appear automatically once the date has been entered. If you make a mistake use b or B to select the item and re- enter the details. The clock SEARCH : PM 13 PLEASE WAIT ! uses the 12-hour Once are you 5 your settings. ADD TV SEARCH system.(Be sure to set AM and correctly.) The new satisfied press MENU to store time will be displayed on the Display Panel. ote perform the Auto Channel Set, the VCR automatically selects the band (TV or CATV) in which When you there channels to be preset. Remember, TV reception, CATV is for cable or are more is for the air antenna wireless cable connection. You v/V to choose the band change by using 4 second item, then press SELECT/ENTER can to display TV or CATV. TV Press MENU to return to a Use (v/V) on the front through the chan- 5 CH/TRK 6 panel cycle(v/V) or CH picture. the DVD+VCR to nels in memory. TO ADD OR ERASE CHANNELS FROM MEMORY This feature allows you to add memory 1 3 channels from manually. Select a channel buttons to add 2 or erase or using the Number Press MENU to enter the main Use b or B or CH/TRK(v/V) delete. to select menu. (TUNING SET) then press SELECT/ENTER. 4 Use v or V to choose the first item, then press SELECT/ENTER to choose between ADD and DEL(Delete). 5 Press MENU to exit the menu. 15 Before DVD General This manual Operation Temporary Explanation gives the basic instructions for operating require specific operation or allow only limited operation during playback. When this occurs, the symbol appears on the TV screen, indicating that the operation is not permitted by the the DVD+VCR. Some DVDs DVD+VCR or is not available On-Screen on the disc. 1 ALL Repeat Title(DVD) Repeat Chapter(DVD) Repeat Track Repeat All Tracks Repeat A-B Resume Action menu. (non-PBC Video CDs (non-PBC only) Video CDs only) Repeat Off the display operation Press DISPLAY TRACK OFF Display general playback status can be displayed on screen. Some options can be changed on the On-screen CHAPT AB The TV TITLE Feedback Field Icons play from this prohibited or point not available otes Some discs may not provide all of the features on the display example shown below. If no button is pressed for 10 seconds, the on-screen display disappears. during playback. on-screen Use v/V to select option. highlighted. an 2 The selected 3 change the setting The number buttons can be also be used for Use b/B to numbers option (e.g., title will be number). For of an some press SELECT/ENTER to execute the option. setting functions, setting. DVD Options Title Number 1/3 Chapter Number 1/12 Time search 0:16:57 Audio language and Digital Audio Output Subtitle 1 D 5.1CH mode language Angle ABC OFF 1/1 Sound VCD2.0 ENG NORM. titles, and skips Shows the current title number and total number of to the desired title number. b/B,or Numeric, SELECT/ENTER Shows the current chapter number and total number of chapters, and skips to the desired chapter number. b/B,or Numeric, SELECT/ENTER Shows the elapsed playing time, and searches the point by the elapsed time directly. Numeric, SELECT/ENTER Shows the current audio soundtrack language, encoding method, and channel number, and changes the setting. Shows the current subtitles language, and changes the setting. Shows the current angle number and total number of angles, and changes the angle number. Shows the current sound mode, and changes the setting. Function (Use 3/4 to select desired option) Track Number 1/4 Time Shows the current track number, total number of tracks and PBC On mode, and skip to the desired track number. 0:20:09 Shows the elapsed playing time (Display only) STER. Shows the audio channel, and changes the audio channel. Audio Channel 16 Selection Method b/B, AUDIO b/B, SUBTITLE b/B, ANGLE b/B VCD1.1 Options Sound Function (Use v/V to select desired option) NORM. Shows the current sound mode, and changes the setting. Selection Method 1/2,or Numbers, SELECT/ENTER -- 1/2,or AUDIO 1/2 Before DVD Initial You Operation (Continued) Menu Settings Select set your own Personal Preferences on the can DVD+VCR. General 1 you Language a see language Operation appears. English Disc Subtitle Spanish Disc Menu Portuguese TV Disc Subtitle English Disc Menu Spanish Rating Portuguese Country Code Digital Audio Scan Audio Picture Italian Chinese Output Polish TV Aspect DVD 4:3 Letterbox: Select when Others Use v/V to select the desired option. setting for the alternate setting(s). will show the current option, well as While the desired as is selected, press B, then v/V to select the desired setting. option 3 SELECT/ENTER 4 Some options require SETUP, RETURN, 5 setup Press nected. Displays above and below the Press or PLAY (H) to exit the menu. con- masking bars standard 4:3 TV is con- Displays pictures cropped picture are cut off. Both sides of the 16:9 Wide: Select when a 16:9 wide TV is connected. Disc Audio 4:3 Letterbox Disc Subtitle 4:3 Panscan Disc Menu 16:9 Wide Rating TV Language DVD language Language Digital for the disc's Menu, Audio, and Code Aspect Menu Language a a with to fill your TV screen. Country Select standard 4:3 TV is images picture. 4:3 Panscan: Select when nected. a theatrical to confirm your selection. additional steps. Disc Output Others Other------------ selected Language German Language Digital screen PREATION Code French Aspect Progressive The menu Aspect Menu 2 This is the Original Disc Audio Menu menu. Disc Audio Country menu TV Setup Rating Press SETUP. The setup for the when you press SETUP. Audio Output Others Subtitle. Original original language set for the disc is selected. language, use number buttons to enter the corresponding 4-digit number according to the language code list on page 35. If you enter the wrong language code, press CLEAR. Other : : The To select another ote Disc Language selection may not work for English Disc Subtitle Disc Menu Spanish Rating Portuguese Country Code Aspect Menu French German Language Progressive Digital DVDs. Original Disc Audio TV some Scan Audio Output Italian Chinese Polish Other------------ Others 17 Before DVD Operation (Continued) Sound Digital Others Audio The DRC, Vocal, PBC and Auto Output Each DVD disc has variety of audio output options. Digital Audio Output according to a Set the DVD+VCR's the type of audio system you use. Use v/V to select the desired SELECT/ENTER. The is changed you have connected the DVD+VCR's DIGITAL AUDIO OUT jack to a Dolby Digital decoder (or an amplifier or with equipment Dolby Digital decoder). a be can setting option and press of the selected option between On and Off. DOLBY DIGITAL/PCM: Select DOLBY DIGITAL/PCM if other Play settings changed. Disc Audio DRC On Disc Subtitle Vocal On Disc Menu PBC Rating Auto Country TV jack amplifier or other equipment with a DTS decoder, Dolby Digital decoder or MPEG decoder. Off Code Aspect Menu Stream/PCM: Select Stream/PCM if you have connected the DVD+VCR's DIGITAL AUDIO OUT On Play Language Audio Digital Output to an PCM: Select when connected to a 2 channel digital The DVD+VCR outputs sounds in the PCM 2ch format when you play a DVD video disc stereo amplifier. recorded with a Dolby Digital, MPEG1, or MPEG2 recording system. /PCM Disc Subtitle Stream/PCM Disc Menu PCM Rating Country Code Aspect Menu Dynamic Range Control (DRC) With the DVD format, you can hear a program's soundtrack in the most accurate and realistic presentation thanks to possible, DOLBY DIGITAL Disc Audio TV Others 48 KHz Language Digital Audio Sample Freq. digital audio technology. However, you may wish to compress the dynamic range of the audio output (the difference between the loudest sounds and the quietest ones). Then, you may losing clarity at a lower volume without listen to a movie of sound. Set DRC to On for this effect. 96KHz Output Others Vocal Set Vocal to On only DVD is The karaoke channels playing. when a multi-channel karaoke on the disc will mix into normal stereo sound. Sample Frequency To Sample Frequency setting, first select the desired Digital Audio Output as indicated as above. If your receiver or amplifier is NOT capable of handling 96KHz signals, select 48KHz. When this choice is made, this unit will automatically convert any 96KHz signals to 48KHz so your system can decode them. If your receiver or amplifier is capable of handling 96KHz signals, select 96KHz. When this choice is made, this unit will pass each type of signal through without any further processing. change the PBC Set Playback Control (PBC) On: Video CDs with PBC are Off: Video CDs with PBC are to On or Off. played according to the PBC. played the same way as Audio CDs. Auto You Play can ically set up the DVD starts If Auto Play search a play playing Player so a DVD disc automat- whenever the DVD is inserted. mode is set to On, this DVD player will playback time is long most and then title that back the title automatically. On: Auto Play function is activated. Off: Auto Play function is not activated. ote The Auto 18 Play function may not work for some DVDs. Before DVD Operation (Continued) Parental Control Rating scenes on the disc. These "Country Code List", with alternative played Disc Audio 8 Disc Subtitle 7 Disc Menu 6 Rating 5 Country TV Code Menu TV Code Aspect Menu scenes. Language Digital Audio Output Others Select the 1 buttons Country on Code the setup While option using Others 3 of on left. the v/V buttons. the first character Select Rating on the Setup v/V using menu Press 2 to shift to second character and select buttons. v/V buttons. the second character 2 While 3 When you have not entered a password yet. Enter a 4-digit password using the numbered but- Rating is selected, press B. Press When you have already entered a password; Enter a 4-digit password using the numerical buttons to confirm the personal 4-digit security password, then press SELECT/ENTER. If you make a ote 4-digit password is necessary when password changed (see "Changing the 4-digit password" below ). the 1 pressing SELECT/ENTER, 4-digit security password again. to exit the Confirmation of the is Changing mistake before press CLEAR and enter then menu. personal 4-digit security password, then press SELECT/ENTER. Enter the 4-digit password again and press SELECT/ENTER to verify. 4 to confirm Code tons to create a B. Code is selected, Follow Unlock Change 1 the v/V menu. Country press 2 step "Rating" 3 Select using 4 5 using SELECT/ENTER your Country 6 selection, press SETUP 2 Output US Rating Country 1 Audio Digital PREATION Code Set Disc Menu are 3 Language 37.). Disc Subtitle 4 Aspect page Disc Audio country dependent. The Parental Control feature allows you to prevent discs from being played by your children to have certain discs country whose standards were used disc, referring to the list (See a to rate the DVD video rated scenes are from 1 to 8, and alternatively, more suitable scenes available for selection on some discs. Ratings are or DVD Enter the code of DVD Movies on DVDs may contain scenes not suitable for children. Therefore, discs may contain Parental Control information that applies to the complete disc or to certain Code Country 2 3 Follow the 4-digit password 1-2 as shown above to the left (Rating). password, then press SELECT/ENTER. Select Change using v/V buttons then press Steps Enter the old SELECT/ENTER. using v/V buttons. One (1) has the least playback restrictions. Eight (8) has the most playback restrictions. 4 Unlock: If you select 5 Enter exactly the same password a second verify by pressing SELECT/ENTER. 6 Press SETUP to exit the Select a rating from 1 to 8 Unlock, Parental Control is not active. The disc will Ratings play in full. 1 to 8: Some discs contain scenes not suitable for children. If you set a rating for the DVD+VCR, all disc scenes with the same rating lower will be played played. Higher rated unless an alternative scene is available the disc. The alternative must have the or a lower one. will If no same suitable alternative is You must enter the playback stop. word or change the rating or will not be scenes on rating found, 4-digit passplay the If you Press SELECT/ENTER to confirm your rating then press SETUP to exit the new 4-digit password, then press time and menu. forget your 4-digit password If you forget your password, to clear the current password follow the procedure below. 1 Press SETUP to display 2 Enter the number 210499. The level in order to disc. 5 selection, Enter the SELECT/ENTER. 3 6-digit the setup menu. 4-digit password is cleared. Enter a new password as shown above to the left (Rating). menu. 19 Tape Operation Normal Search Playback This function lets you quickly and visually search for desired tape section in either direction: forward or Preparation: reverse. Turn on the TV. Tune the TV to the DVD+VCR output channel (CH 3 or set the TV's source selector to VIDEO. If a direct VIDEO/AUDIO connection is made between the 4) or DVD+VCR and the TV, set the TV's source selector to VIDEO. Output Source to VCR as shown in "Setting the Viewing Source" on page 6. Insert prerecorded a indicator will The playback, the TV/VCR selector switches mode automatically. In to If the more enter the protect the tape and video heads. press PLAY (H). to playback, Still Picture and Frame-by-Frame Playback 1 Press PAUSE/STEP Still If (X) during playback. will appear picture video more than 5 PAUSE/STEP (X) repeatedly to advance the one frame at a time while viewing a still playback, press PLAY (H). 1 While in still mode, press FORWARD (>). The tape will be played back at a speed 1/19 times slower than the normal During slow playback, speed. use CH/TRK (v/V) on the Remote Control to minimize noise bands. Tracking remove snow or using Slow Motion Tracking Control tracking it picture picture. 3 To return to tape reaches the end before STOP (x) is The automatic screen. picture vibrates vertically, stabilize CH/TRK (v/V) on the remote control. screen. pressed, the DVD+VCR will automatically stop, rewind and eject the tape, and it will turn itself off. Auto the TV on still a 2 Press to VCR stop playback. the TV mode, automatically If the DVD+VCR is left in the STILL mode for DVD+VCR. on If the DVD+VCR is left in the SEARCH mode for minutes, the DVD+VCR will automatically enter the STOP mode to protect the tape and video heads. It is not necessary to select the tape speed for It will be automatically selected by the Press STOP (>) . playback. 3 STOP appears(x) FORWARD than 3 minutes, the DVD+VCR will PLAY indicator in the display lighted. If it is, press POWER once. If a tape without a safety tab is inserted, the unit will start playback automatically. screen or mode. 2 To return to will window is not Press PLAY (H) once. PLAY appears on the TV (.) The DVD+VCR will be activated in the SEARCH video cassette. light and the DVD+VCR power-up automatically. Make sure that the 2 1 Press BACKWARD during playback. Set the 1 a function adjusts the picture If slow motion mode continues for to the DVD+VCR will streaks. The AUTO TRACKING function works in the following cases: than 3 minutes, more automatically change playback to mode. 2 To return to playback, press PLAY (H). A tape is played back for the first time. Tape speed (SP, EP) changes. Streaks or snow CM appear because of scratches on the tape. Manual Tracking If noise appears on the screen during playback, press either CH/TRK v/V on the remote control or CH (v/V) the front reduced. on panel until the noise on the screen is Special Special 1 Press CM SKIP Effect effects Playbacks playback (noise bars) will appear on the TV screen. This is normal. automatically muted during special effect modes, so there is no sound during search. During high-speed picture search mode, a short period is needed to stabilize tape speed when re-entering the PLAY mode. Slight interference may be observed during this period. during playback. picture mode playback search through complete, the DVD+VCR automatically. EZ (EASY) Repeat Yo u can 30 1 replay a specified segment 3 will go twice. and hold ez REPEAT for more than 3 seconds at the end of the segment and your DVD+VCR will start reverse search. During playback, press Release REPEAT at the of the beginning 2 segment. The segment is replayed twice ez automatically. To return to normal easy repeat 20 short program or Skipping time can be extended by pressing CM SKIP repeatedly. Subsequent presses result in advancing the fast forward picture search time by 30-second increments (maximum minutes). into notes commercials The tape will fast forward seconds of recording. 2 When the search is Horizontal lines The audio is skipping segments. In case of vertical jitter, adjust these controls very carefully. Tracking is automatically reset to normal when the tape is ejected or the power cord is unplugged for more than 3 seconds. Skip (Commercial Skip) This is useful for play, playback. press PLAY (H) during Tape Operation (Continued) Normal Timer Recording This DVD+VCR Preparation: the power of both the DVD+VCR and TV. Tune the TV to the DVD+VCR output channel (CH 3 Turn on or 4) or set the TV's source selector to VIDEO. If a direct VIDEO/AUDIO connection is made between the DVD+VCR and the TV, set the TV's source selector to 1 can be programmed to record up to 7 programs within a period of 1 year. For unattended recording, the timer needs to know the channels to be recorded and the Turn video cassette with the a safety Select the desired channel If you tab intact. (v/V). recording from another source via audio/video input jacks (at the Rear or Front panel), select the LINE1 or LINE2 by pressing INPUT. 3 SPEED. recording speed (SP This DVD+VCR is not designed Set the MTS mode 4 by using CH/TRK are Set the desired Press REC/ITR 5 Recording the If as (z) Be EP) desired (See page a to CH 23-24). indicator will light in seconds, press STOP (x) twice v or V to Press ---------- ------ ---------- ------ ---------- ------ ---------- ------ ---------- TIME ----:---- ----:----SP ----:---- ----:----SP ----:---- ----:----SP ----:---- ----:----SP ----:---- ----:----SP ----:---- ----:----SP ----:---- ----:----SP to end B select channel number Press SELECT/ENTER before entering a date to select They are DLY (daily) to record every day except Saturday and Sunday at the set time, or individual days e.g. MO (Monday) to record at the one of the automated features. time every week. Use b SELECT/ENTER to confirm. recording (X) to pause the tape during recording. 6 display window. When you want to continue recording, press PAUSE/STEP (X) or press REC/ITR (z). After 5 minutes in pause mode, the tape will be stopped automatically to protect the tape and the video heads. To record Press 7 uses a B to during recording. the TV, select the channel to be viewed. select, then press 12 hour clock. select the v or V to move recording speed. 04 DATE JUL 6 ------ ---------- ------ ---------- ------ ---------- ------ ---------- ------ ---------- ------ ---------- TIME 6:00 ----:---- 7:30 SP ----:----SP ----:---- ----:----SP ----:---- ----:----SP ----:---- ----:----SP ----:---- ----:----SP ----:---- ----:----SP Check that the timer event details 8 they 9 are are, press MENU to save your Press MENU Use the between SP and EP. CH TV program while another The TV indicator appears. to Enter the time of the start and end of the pro- one Use TV/VCR to select the TV mode or B gram that you wish to record. The VCR The REC indicator will flash in the (or and enter the date of the program that same Press PAUSE/STEP then press wish to record. turn itself off. To pause Using ------ menu menu. tape reaches the end before STOP (x) is pressed, the DVD+VCR will automatically stop, rewind, eject the 2 ---------- will appear. 3 4 L1(LINE1), L2(LINE2)) 5 you If the 1 ---------- ------ 4). DELETE: Use cassette 6 recording. watching DATE ------ or Press SELECT/ENTER to enter the timer record safety tab is loaded, the be ejected automatically. tape and menu 1 Use b/B choose the REC 2 SELECT/ENTER. with once. cassette with no Within 5 times. the power of both the DVD+VCR and the TV. the TV is set to the DVD+VCR output channel (3 on sure to record in LP mode. (The REC will start. or display window.) will 2 ending Press MENU and the MAIN 2 1 and starting Preparation: VIDEO. Insert Recording again correct, if settings. to remove the menu. ips Always use PAUSE/STEP (X) for best results when making changes during recording. For example: To change channels during recording, first press PAUSE/STEP (X) to the desired channel PAUSE/STEP put the unit in pause mode. Then select the DVD+VCR, and press on (X) again to resume recording. otes If PLEASE CORRECT THE DATA! is displayed you have entered incorrect information. Check the details on the television screen and re-enter it. If you want to enter more Timer above process from point 3. recordings, repeat the If all 7 programs have been entered, FULLY PROGRAMMED message will appear. 21 OPERATION Tape Operation (Continued) Checking (Erasing) Programming Programming is turned can Timer Record Instant Timer Instant Timer be checked whenever the DVD+VCR on. easily of a Recording Recording allows you to make timer. Press MENU and the MAIN menu will appear. 1 Use choose the REC then press 2 SELECT/ENTER. Use select the timer slot that you wish 3 change. Press delete SELECT/ENTER edit that 4 entry. Use the buttons select the b or B to menu v or V to Preparation: b to to or b or B to tion you wish to change and the to change those sections. sec- v or V buttons the power of both the DVD+VCR and the TV. the TV is tuned to the DVD+VCR output channel (3 direct VIDEO/AUDIO connection is made between the Turn Be If on sure a DVD+VCR and the TV, set the TV's to 1 Insert a video cassette with the Select the desired channel with CH 04 DATE JUL 6 ------ ---------- ------ ---------- ------ ---------- ------ ---------- ------ ---------- ------ ---------- 7:30 ----:---- ----:----SP ----:-------:---- ----:----SP ----:----SP ----:---- ----:----SP ----:---- ----:----SP ----:----SP ----:---- SP screen. are LINE2. 3 DELETE: Press MENU to return to the TV or recording from another source via audio/video input jacks (at the Rear or Front panel), select LINE1 or TIME 6:00 CH/TRK(v/V) the TV on tab intact. safety 2 number (0-9). If you 4). or selector to VIDEO. source The channel number appears 5 recording a preset length without using the program Select the desired speed will appear Press REC/ITR twice. The tape screen. 4 recording speed (SP The menu as Recording (z) on the TV illustrated, will appear on Press REC/ITR If the starting and ending times of two or more timer recordings overlap on the same day, priority is given to the earliest recording. For example, in the diagram PROGRAM 2 will not be recorded until PROGRAM 1 is finished. The first part of PROGRAM 2 will not be recorded. Likewise, PROGRAM 3 will not be recorded until PROGRAM 2 is finished, and so on. the TV screen. to select the (z) repeatedly At the end of the recording screen. will start. 5 recording time length. Program Priority EP) or with SPEED. recording, the DVD+VCR will stop and shut off. During Instant Timer Recording, changing the channel the DVD+VCR will not be possible. You can stop the recording by pressing STOP (x) on twice, within 5 seconds.. INSTANT TIMER RECORD MENU REC CH4 0H30 ..... 9H00 0H00 SP 0H30 Length Display (each additional press of REC/ITR (z) increases recording time 30 minutes) To extend the Recording Time The recording time can be extended anytime by pressing REC/ITR (z). Subsequent presses result in advancing the recording time by 30-minute increments. otes If you press PAUSE/STEP (X) during instant timer recording, the DVD+VCR will enter the recording pause mode. Instant timer recording is cancelled. If the DVD+VCR is set to normal 22 recording mode. "0H00", the DVD+VCR goes to Tape Operation (Continued) and Dubbing You easily VHS Hi-Fi Stereo Editing edit or System/ MTS Broadcast dub camcorder/VCR recordings panel audio/video jacks. These direct A/V jacks provide better picture results than using the RF jack on the rear panel. can to the DVD+VCR via the front/rear Connect the camcorder's outputs another VCR's) A/V how to record and "LINE2". input channel LINE2.) (use INPUT to input channel Playback LINE1 by pressing INPUT twice. DVD+VCR, you a tape in the Hi-Fi audio mode. with Hi-Fi Stereo Audio Sound input jacks or a stereo Hi-Fi recorded this unit to the video playing. recording to begin, press (z) once to start. a tapes, we recommend the connection of home stereo audio system. can see When you desire the DVD+VCR's REC/ITR can play audio system is required for true stereo playback. To experience the full and rich stereo sound available with Play the tape in the camcorder (or another VCR). If you have a TV attached to your You with the VHS Hi-Fi audio A stereo TV with AUDIO/VIDEO If you have connected your DVD+VCR to the A/V input jacks on the rear of DVD+VCR, you should select the 4 equipped sound system for recording and playback. The information below gives a brief description of Hi-Fi audio and to your DVD+VCR as illustrated on page 13. Set the select (or This DVD+VCR is stop the recording by pressing STOP (x) twice, within 5 seconds. Press MENU to enter the main 1 Use b or B to select 2 press SELECT/ENTER. menu. (AUDIO SOUND) then ote Before recording, please confirm the recording start position. from DVD to VCR Copying This unit allows you to copy the contents of VHS tape. a DVD to a ote If the DVD you are attempting to copy is copy protected, you will not be able to copy the disc. It is not permitted 3 the left and the right right speaker. (L) is heard from channel sound (R) is : The left channel sound (L) is heard from speakers. RIGHT : The right channel sound (R) is heard from both speakers. MONO : Only displayed when played back. Tape a The DVD will go into Play mode and the VCR will go into Record mode. If the DVD disc menu (H) manually appears, you may need to press to begin copying. the Process Stop Copy 4 When the is finished playing, press STOP (x) DVD twice to end the copy within 5 seconds. You must stop the Copy process manually when the DVD movie ends, or the unit may replay and record over Press MENU to exit the 4 MTS (Multi-Channel menu TV . Sound) This DVD+VCR will decode MTS stereo and "COPY" indicator will light. and The left channel sound LEFT blank VHS video tape into the VCR deck. Press the COPY button on the unit front panel. over buttons to choose among below: both Insert the disc you wish to copy in the DVD deck and close the disc tray. PLAY : speaker heard from the Insert Disc Insert v or V STEREO to copy Macrovision encoded DVDs. "Lock" is displayed in the display window. Insert VHS Use the (SAP) off-the-air broadcast sound signals. bilingual It also decodes stereo TV sound from local cable as long and use as they operate on companies, frequencies MTS stereo/bilingual TV assigned the EIA-recommended cable sound system. again. ote When you stop the DVD playback during recording mode stops automatically. copying, the VCR 23 OPERATION Tape Operation (Continued) Multichannel TV Sound Indicator Shows SELECT/ENTER is One light, depending on the Shows MTS broadcast. TV Tape Counter Memory Feature Real-Time Counter pressed. both of the indicators will or (MTS) illustrated below when onscreen as length of tape in hours, minutes, and run seconds. Press CLK/CNT to select the real-time screen counter STEREO CH4 Lights up when a stereo broadcast is being received. STEREO/SAP display. press of CLK/CNT illustrated below. Every the TV changes screen as SAP Lights up when a SAP BILINGUAL broadcast is being received. SE 2:15 AM 0:05:25 CLOCK COUNTER otes If only STEREO appears The DVD+VCR on the TV Counter screen. record in stereo onto the VHS Hi-Fi audio can tracks when the BROADCAST TYPE is in the STEREO tion. The DVD+VCR will also record mono If mono changes to "0:00:00" when the cassette is ejected. posi- The real-time counter does not operate if recorded on the tape. audio onto the audio track. The real-time counter will not work unless only SAP appears on the TV screen. nothing a is tape is inserted. Set the BROADCAST TYPE to SAP. If STEREO/SAP appears on the TV screen Use the BROADCAST TYPE to select the desired recording mode (STEREO SAP or SAP). (Second a Audio second a Program) Recording Second Audio language When the station broadcasts follow the Insert procedure a 3 Use or a Program, which additional information. Second Audio Program, below to record the SAP. video cassette with the 1 Press MENU 2 safety tab intact. select Do this if only the SAP appears on the TV know the program will use the SAP. v or V screen or you SAP MONO Select the desired recording speed (SP 5 SPEED Select SAP 6 REC/ITR (z) 7 recording or EP) button. the desired channel. Press should appear screen. once are now the program you see and hear on the TV. With in 5 seconds, press STOP (x) twice 8 recording 24 or 3 a to tape. display the TV screen. At the point that you want locate later, reset the real-time counter to "0:00:00" by pressing 5 6 Continue to play Press STOP (x ) or record. when recording to end or playback finishes. Press BACKWARD The tape (.). automatically stops returns to about "0:00:00". STEREO You 1 Begin recording playing Press CLK/CNT repeatedly 2 real-time the 4 (BROADCAST TYPE) Select Broadcast type to SAP with the the TV to CLEAR. and then press MENU. on section of tape you want to or if you want to return a immediately after recording the same point several times. counter on then press SELECT/ENTER. with the This is useful if there is to enter the main menu. b or B to Function Memory view Some stations transmit is used for Counter when the tape counter Tape Operation (Continued) Video Doctor Additional Informatio In manual recording, Timer recording, Instant Timer Recording, playback, or fast forward modes, the DVD+VCR automatically starts rewinding the tape at the end of the tape. The cassette will stop at the beginning of the tape and be ejected, and the DVD+VCR will turn itself off. After you have finished using the DVD+VCR, rewind, eject, and remove the cassette. Place the cassette in its protec- The Video Doctor will show the status of aspects of the VCR. Press MENU to enter the main 1 Use select 2 press SELECT/ENTER. b or B to tive sleeve to protect it from dust. It is not necessary to rewind the cassette before removing it, but if you do, it will ready Be sure to play TAPE STATUS NO. OF TIMER PROGRAM channel you wish to record. The channel that is being recorded can always be checked by tuning the television to (3 then HEAD STATUS or the DVD+VCR channel (VIDEO DOCTOR) ANTENNA CONNECT record the next time you use it. the DVD+VCR Channel Selector is on the correct be menu. NEXT TIMER PROGRAM OK 4) and pressing the TV/VCR or selector to turn the DVD+VCR's TV indicator off. Do not attempt to hook up more than the DVD+VCR for either recording or Auto one television set to playback. 3 Play System cassette a The Output (with Source is the playback. safety tab removed). changed to VCR mode PLEASE CHECK TV automatically. PLEASE CLEAN: The tape heads need ejected after rewinding and the DVD+VCR automatically. AUTO protection tabs removed, insert recording. PLAY REWIND AUTO POWER TAPE Shows the number of timer Auto power off does not function during regular DVD play mode. (DVD+VCR power stays on.) S-VHS Quasi This DVD+VCR an can play back S-VHS recorded abbreviation for S-VHS Quasi Background on-screen Use b or B Select a to select desired mode and then press MENU. Playback. Function Press MENU to enter the main 2 press SELECT/ENTER. 3 recording programmed. Shows the current status of timer Press MENU to 4 vision the remove recording. menu from the tele- screen. Playback (SQPB) tapes, however, it cannot make recordings using S-VHS format tapes. 1 tape suitable for NEXT TIMER PROGRAM ote SQPB is a NO. OF TIMER PROGRAM OFF EJECT cleaning NOT RECORDABLE: The Cassette in the VCR has had its AUTO AUTO Connect the VCR to the antenna and : correctly and securely. TA PE STATUS The cassette is LOAD following HEAD STATUS The power turns on automatically and playback begins. At the end of the tape, the DVD+VCR stops, then rewinds. turns itself off buttons to check the v or V ANTENNA CONNECT This DVD+VCR features automatic Load Use the features. menu. (BACKGROUND) (ON or OFF) OPR (Optimum Picture Response) This enhances the picture from the video tape by adjusting to the condition of the video tape. If you feel that the picture needs adjusting you can manually change the OPR setting. You can only set OPR when tape is playing in the VCR. Press MENU to enter the main then with v or V 1 Use the select 2 SELECT/ENTER. Use the buttons 3 b or B to menu. (OPR) to select v or V then press OFF, SOFT or HARD. OFF SOFT ON HARD OFF 4 Press MENU to exit the menus. 25 a OPERATION DVD and Video CD DVDs and Video CD Playing Playback Setup Turn on Operation VCD2.0 DVD the TV and select the video General Features VCD1.1 input ote source con- nected to the DVD+VCR. Unless stated otherwise, all operations described the remote control. Some features may also be available Audio system: Turn on the audio system and select input source connected to the DVD+VCR. on the Setup use menu. the Set the Output Source to DVD as Viewing Source" on page 6. the Press OPEN/CLOSE (Z) 1 Load chosen disc 2 facingyour up. "Selecting to open the disc When tray. tray, with the label menu If The a menu screen is When Use b/B/v/V buttons to select the loading can move to num- on a more title/chapter DISC MENU to return to the 1 /12 VCD1.1 disc has than as one more 1/3 than track, you one chapter can move or a to another follows: (.) or FORWARD (>) briefly during playback to return to the beginning of the current chapter/track or to select the next chapter/track. Press BACKWARD (.) twice briefly to step back to the previous chapter/track. To go directly to any chapter/track during playback, press DISPLAY. Use v/V to select Chapter/track icon. Then, enter the chapter/track number with the number buttons (0-9). a you playback. or title, you Press BACKWARD view, then press SELECT/ENTER to start Press TITLE title chapter/track displayed DVD want to a disc has may be displayed first after Video CD which contains a menu. or one to another CHAPTER/TRACK VCD2.0 DVD appear instead. menu screen DVD Moving automatically. If playback does not PLAY (H). In some cases, the disc might than more follows: as Press DISPLAY, then press the appropriate (0-9) to select a title number. starts start, press disc has 1/3 DVD sure the side you want to play is facing down. Press OPEN/CLOSE (Z) to close the tray. 3 Playback a to another TITLE bered button double-sided DVD is inserted, make a Moving another title in the When shown in menu screen. VCD2.0 Use the number buttons to select the track you want to view. Press RETURN to return to the menu screen. Menu setting the and the exact operating procedures for may differ depending on the disc. Follow the instructions on the each menu screen. using Slow Motion 1 Press PAUSE/STEP menu The DVD+VCR will 2 Press BACKWARD You also may set PBC to Off under setup. See page 18. during the 4-digit password "Parental Control", on page 19). DVDs may have a Region Code. Your DVD+VCR will not play discs that have (see Code different from your DVD+VCR. The Code for this DVD+VCR is 4 (four). a (.) or FORWARD (>) to required speed: t 1/16, t 1/8, t 1/4, 1/2 (backward), or T 1/16, T 1/8, T 1/4, T 1/2 (forward). With a Video CD, the Slow motion speed changes: T 1/16, T 1/8, T 1/4 (forward only). To return to playback, press PLAY (H). keep a fixed image displayed long time. on 4 Region Region the ote screen screen saver picture appears when you leave the DVD+VCR in stop mode for about five minutes. 26 pause mode. a Screen Saver The go into PAUSE mode. or FORWARD (>) (.) select the must be entered and/or the disc must be authorized for (X) during playback. now The DVD+VCR will enter SLOW mode. If Parental Control is set and the disc is not within the Do not VCD1.1 3 Use BACKWARD otes Rating settings (not authorized), VCD2.0 DVD Slow motion Video CD. playback in reverse is not applicable for t DVD and Video CD General Features Still Picture and VCD2.0 DVD frame 1 To DVD, you (X) during playback. go into PAUSE mode. advance the picture frame The now can press PLAY playback, VCD2.0 DVD 3 To exit by on On (.) or FORWARD (>) during playback. The DVD+VCR will go into SEARCH mode. (.) or FORWARD (>) required speed: mX2, mX4, mX16, mX100 (backward) or MX2, MX4, MX16, MX100 (forward). With a Video CD, the Search speed changes: mX2, mX4, mX8 (backward) or MX2, MX4, MX8 (forward). To return to playback, press PLAY (H). to select the Karaoke DVD VCD2.0 during playback or in Stop mode. automatically begins Random Playback and 2 To return to normal the TV on screen. on press RANDOM until the TV screen. Repeat A-B A* AB To repeat VCD2.0 DVD sequence in a a " A " * appears 2 Press A-B briefly on the TV at your chosen end again works with DVD Karaoke discs and briefly on the TV screen, and the repeat sequence begins ("AyB" appears the display window). 3 To cancel the sequence, press A-B. 0:16:57 DVD 1 Press DISPLAY appears on during playback. the TRACK 4 Within 10 1 To - ALL The The on the TV currently playing, Repeat mode, in the box. seconds, press SELECT/ENTER. starts from the selected time on the disc. If you enter an invalid time, playback will continue from the current point. DVD VCD2.0 VCD1.1 3D SUR produce a 3D Surround effect, which playback from two conventional stereo five more speakers, instead of the speakers normally required to listen to multi- channel audio from screen. press REPEAT can a 1 Press DISPLAY a or home theater system. during playback. 2 Use v/V to select the sound icon. Repeat Title icon appears 3 To exit right simulates multi-channel audio Repeat Chapter/Title/Off Repeat Chapter icon appears repeat the title second time. elapsed playing time of the OFF REPEAT. 2 To dis- screen. VCD1.1 repeat the currently playing chapter, press The on-screen at Playback This unit DVD Video Discs The playing If you enter the wrong numbers, press CLEAR to remove the numbers you entered. Then enter the correct numbers. NORM. TITLE CHAPT -:--:-- The Time Search function allows you to start any chosen time on the disc. 3D Surround VCD2.0 point. "A B" appears The "-:--:--" appears in the Time Search box. to use the Random function. See DVD point. screen. 3 Within 10 seconds, use the numbered buttons to enter the required start time. Enter hours, minutes OnaVideoCDwithPBC,youmustsetPBCtoOffon Repeat title: 2 Within 10 seconds, use v/V to select the Time Search icon in the on-screen display. video CD without PBC. menu VCD1.1 1 Press A-B at your chosen start and seconds from left to the setup page 18. third time. current disc. ote only a screen. OFF The Time Search box shows the ips By pressing BACKWARD (.) or FORWARD (>) during Random playback, the unit selects another title (track) and resumes Random playback. This function screen. Video CD with PBC, you must set PBC to Off on the menu to use the Repeat function. See page 19. play playback, "NORMAL" appears the TV on on the TV screen. press REPEAT Repeat Off icon appears on a VCD1.1 1 Press RANDOM "RANDOM" appears the TV on screen. press REPEAT mode, press REPEAT Time Search Random The unit a setup VCD1.1 2 Press and hold BACKWARD 3 the TV ote (H). for about two seconds repeatedly All icon appears Repeat on currently playing, Repeat Off icon appears The 1 Press and hold BACKWARD now Repeat press REPEAT. currently playing, Repeat Track icon appears repeat the disc second time. by pressing PAUSE/STEP (X) repeatedly Search Repeat Track/All/Off repeat the track The the remote control. 3 To return to - 2 To VCD1.1 The DVD+VCR will a Video CDs (continued) Frame-by-Frame Playback 1 Press PAUSE/STEP 2 With Operation (Continued) the TV a third time. screen. The sound option will be highlighted. 3 Use b/B to to select "3D SUR". To turn off the 3D Surround effect, select "NORM.". 27 OPERATION DVD and Video CD General Features Zoom DVD VCD2.0 Operation (Continued) (Continued) VCD1.1 during playback discs: Menus still or playback to acti- repeatedly, the magnification level steps. 2 Use b/B/v/V buttons to move through the zoomed picture. 3 Press CLEAR to the resume normal playback or DVDs may contain menus that allow you to access special features. To use the disc menu, press DISC MENU. Then, press the appropriate number button to select an option. Or, use b/B/v/V buttons to highlight your selection, then press SELECT/ENTER. vate the Zoom function. If you press ZOOM increases up to six return to 1 Press TITLE. If the current title has paused image. screen. otes zoom The zoom function may not work for function may not work on some DVDs. 3 To multi-angle scenes. DVD VCD2.0 start playback a memorized point. Up to nine points can be memorized. To enter a mark, follow these steps. 1 on the TV briefly. screen 1 to enter up to nine Marker Repeat step points may appear. angles, spoken language chapters for the title. camera options, and again. DVD menu Camera is displayed. the disc menu, press DISC MENU remove DVD Angle If the disc contains During disc playback, press MARKER when playback reaches the spot that you want to memorize. The Marker icon will appear 2 list menu the title menu, press TITLE remove The disc 2 To from menu, the menu will appear on the 1 Press DISC MENU. VCD1.1 MARKER SEARCH 1/9 can menu can Disc Menu Marker Search a Otherwise, the disc and subtitle The DVD Title Menu 2 The You the contents of DVD Video Checking The Zoom function allows you to enlarge the video image and to move through the enlarged image. 1 Press ZOOM DVD Features Special scenes again. 1/1 recorded at different camera angles, you can change to a different camera angle during playback. Press ANGLE repeatedly during playback to select desired angle. The number of the current on a angle appears on the display. disc. 1 ENG To Recall 1 During Changing Marked Scene a disc playback, The Marker Search use Press AUDIO will appear menu on the SEARCH. During disc playback, will appear on the 3 Press CLEAR. The Marker number will be erased from the list. 2 and 3 to erase additional Marker numbers. 5 To remove the Audio Channel VCD2.0 Press AUDIO repeatedly during playback to hear (STER., LEFT or RIGHT). VCD1.1 a dif- Subtitles DVD ABC 1 ENG during playback to see the ote screen. Within 10 seconds, use 1/2 or number button to select a Marker number that you want to erase. Repeat steps Changing press SEARCH. menu 2 4 to hear a Press SUBTITLE repeatedly different subtitle languages. Marked Scene The Marker Search repeatedly during playback language or audio track. scene. 4 To remove the MARKER SEARCH menu, press 1 5.1 CH ferent audio channel will start from the Marked a D DVD Language screen. 3 Press SELECT/ENTER. Playback the Audio different audio SEARCH. 2 Within 10 seconds, use 1/2 or number button to select a Marker number that you want to recall. To Clear a the MARKER SEARCH menu, press SEARCH. If appears, the feature is not available Last Condition This player Memory memorizes the user DVD settings on the disc. VCD1.1 for the last disc that you have viewed. Settings remain in memory even if you remove the disc from the player or switch off the player. If you load a disc that has its settings memo- rized, the latest stop position is automatically recalled. otes ote All markers are erased when the disc is ejected. Settings are stored in memory for use any time. This player does not memorize settings of a disc if you switch off the player before commencing to play it. 28 with Audio CD and MP3/WMA Disc Operation Playing an Audio CD and MP3/WMA Disc CD MP3 MP3/WMA 1 Insert play Recordings Recordings on compressed by using the layer-3 file-coding scheme. We call the ".mp3" file extension "MP3 files". MPEG1 audio files that have The right. player can disc and close the tray. Audio CD; Audio CD menu appears on the TV screen go to step 4. MP3/WMA disc; The MP3/WMA-JPEG choice menu appears on the TV screen. Go to step 2 OPERATION not read an MP3 file that has a file extension other than ".mp3". a About JPEG WMA(Window Media Audio) An WMA file is technology. WMA(Windows compression of MP3 WMA Use 3/4 to select the MP3/WMA then press SELECT/ENTER. The MP3/WMA menu appears on the TV screen. Press RETURN to move to the MP3/WMA-JPEG choice menu. MP3 WMA 1. 2. 3. Folder2 Folder3 Folder4 Folder5 Folder6 Folder7 Clear All 5. OFF Microsoft audio Media 3 4 Use 3/4 to select a track then press PLAY or SELECT/ENTER. compatibility the current track's elapsed playing time will appear on the display window and menu. Playback will stop at the end of the disc. Press TITLE to player is - - CD Creator", which creates an ISO9660 file system. single session disc requires MP3/WMA files in the A no MP3/WMA file in the 1st track, it cannot playback MP3/WMA files. If you wish to playback MP3/WMA files, format all the data in 6. File or use a new one. names and must should be named incorporate ".mp3" e.g. "********.MP3" Playback starts. During playback, with this follows: Sampling Frequency / only at 44.1kHz (MP3), 44.1kHz (WMA) Bit rate / within 32 320kbps (MP3), 32 128kbps (WMA) CD-R physical format should be "ISO 9660" If you record MP3/WMA files using the software which cannot create a FILE SYSTEM, for example "Direct-CD" etc., it is impossible to playback MP3/WMA files. We recommend that you use "Easy- the disc (H) offers double the audio the MP3 format. first track. If there is Use 3/4 to select a folder, and SELECT/ENTER. A list of files in the folder appears. Audio) compression - Folder1 00:00 as 22.05 4. Program Folder8 a MP3/WMA Disc limited 2 MP3/WMA An MP3 file is audio data MP3/WMA formatted recordings on CD-ROM, CD-R or CD-RW discs. Before playing MP3/WMA recordings, read the notes on can on About MP3 WMA The DVD+VCR Notes or using or 8 letters or less ".wma" extension "********.WMA". 7. Donotusespecialletterssuchas"/:*?"<>"etc. 8. Total number of files on the disc should be less than 650. to the next page. move Press DISC MENU to move to the previous page. This DVD+VCR requires discs/recordings to meet certain technical standards in order to achieve Program MP3 WMA Program CD TRACK01 FILE 2 TRACK03 FILE 3 TRACK04 FILE 5 TRACK06 FILE 6 TRACK07 FILE 7 Clear All TRACK08 STER. NORM. Audio CD menu 0: 56: 18 Clear All FILE 8 00:00 1 If you are use in a MP3/WMA menu file list and want to return to the Folder the 3/4 to highlight SELECT/ENTER to return to the To stop playback 5 press STOP (x ). and press previous at any other optimal automatically types (including CD-R containing MP3 or WMA files). That require certain pre-existing conditions (see above) to insure compatible playback. OFF Tip list, are of recordable disc formats FILE 4 TRACK05 Pre-recorded DVDs set to these standards. There are many different FILE 1 TRACK02 playback quality. Customers should also note that required permission is in order to download MP3/WMA files and music from the Internet. Our company has no grant such permission. Permission should right to always be sought from the copyright owner. menu screen. time, 29 with Audio CD and MP3/WMA Disc Operation Pause CD MP3 1 Press PAUSE/STEP WMA Repeat (X) during playback. 2 To return to playback, press PAUSE/STEP (X) again. PLAY (H) or CD MP3 WMA or Press BACKWARD . twice the previous track. briefly step back to to of audio CD, to go directly to any track, enter using the numbered buttons (0-9) the track number during playback. Repeat Track/All/Off 1 To 2 Press A-B * " appears on the at your chosen end again menu screen. point. Repeat icon and "A B" appears on the menu and the sequence begins to play repeatedly. CD MP3 3 To exit the sequence and return to normal A-B again. The 3D Surround This unit WMA more Repeat icon and "TRACK" appears the on Repeat icon and "OFF" appears can on the screen, play, CD produce a 3D Surround effect, which speakers normally required channel audio from 1 Press DISPLAY menu press menu screen. simulates multi-channel audio playback from two conventional stereo speakers, instead of the five repeat the track currently playing, press REPEAT. The Repeat icon and "A The FORWARD > briefly during playback to go to the next track or to return to the beginning of the current track. case CD ing point. to another Track Press BACKWARD . In A-B To repeat a sequence. 1 During disc playback, press A-B at your chosen start- press The Moving (Continued) a or or to listen to multi- home theater system. AUDIO during playback. screen. 2 To repeat all tracks on a disc, press REPEAT 2 Use b/B to select the Sound icon. a sec- The Sound icon will be ond time. The Repeat icon and "ALL" appears on the highlighted. 3 Use v/V to select "3D SUR". menu screen. To turn off the 3D Surround effect, select "NORM.". 3 To cancel The Repeat mode, press REPEAT Repeat icon and "OFF" appears Search CD MP3 on The player will now Changing or FORWARD > go into SEARCH mode. or FORWARD > to select the mX4, mX8 required speed: mX2, (backward) or MX2, MX4, MX8 (forward). Search speed and direction are indicated on the menu screen. 3 To exit SEARCH mode, press PLAY Random CD 1 Press RANDOM MP3 (H). WMA during playback or when playback is stopped. The unit automatically begins Random "RAND." appears on the menu screen. edly 30 until "RAND." Playback and playback, press RANDOM repeatdisappears on the menu screen. 2 To return to normal the Audio Channel CD Press AUDIO repeatedly during playback to hear a different audio channel (STER., LEFT, or RIGHT). during playback. 2 Press and hold BACKWARD . repeatedly menu screen. WMA 1 Press and hold BACKWARD . for about two seconds the third time. a with JPEG Disc Operation Viewing JPEG disc a on discs with JPEG files and play can picture CD. read the notes Insert during viewing a picture the previous file. playing JPEG recordings, Recordings on right. Before JPEG disc and close the tray. The MP3/WMA-JPEG choice menu appears TV screen. on the JPEG menu appears 1 Press PAUSE/STEP on the TV once (X) during slide show. go into PAUSE mode. 2 To return to the slide show, press PLAY (H) PAUSE/STEP (X) again. The To Use 3/4 to select the JPEG then press SELECT/ENTER. The JPEG FORWARD > or to advance to the next file or to Still Picture a MP3 WMA 2 to another File Press BACKWARD . This DVD+VCR Kodak Moving JPEG player will now or press flip the picture Press 3/4 during showing a picture picture horizontally or a vertically. to flip the screen. To rotate JPEG Press 1/2 Folder1 Folder2 picture Folder3 Folder4 picture during showing clockwise or a picture to rotate the counter clockwise. Folder5 Folder6 Folder7 Notes Folder8 Slide Speed on Depending 3 Use 3/4 to select a folder, and SELECT/ENTER. A list of files in the folder appears. Press RETURN to move to the MP3/WMA-JPEG choice JPEG Recordings Off menu. upon the size and number of the JPEG a long time for the DVD player to files, it could take read the disc's contents. If you don't see an ondisplay after several minutes, some of the files screen are too big --- reduce the resolution of the JPEG files to less than 2 mega Tip If you list, " are use a file list and want to return to the Folder the 34 buttons on the remote to highlight and press SELECT/ENTER to return to the " previous 4 in menu screen. If you want to view a particular file, press 3/4 to highlight a file and press SELECT/ENTER or PLAY (H). the file starts. Viewing proceeding During viewing a file, press RETURN the previous menu (JPEG menu). Press TITLE to and burn another disc. on the disc should be less than 650. Some disc may be incompatible due to different recording format or condition of disc. When you are using software such as "Easy CD Creator" to burn the jpeg files into the CD-R, ensure that all the selected files have the ".jpg" extensions when copying into the CD layout. If the files have to move to to the next page. Press DISC MENU to move to the previous page. JPEG pixels Total number of files and folders move rename File them names be read shown by as ".jpe" or ".jpeg" extensions, please as ".jpg" files. without ".jpg" extension will not be able to this DVD+VCR. Even JPEG image though the files explorer. are files in windows Folder1 Picture1 Picture2 Picture3 Picture4 Picture5 Picture6 Picture7 5/32 1024X768 Slide Speed Off 5/32 1024X768 Picture5.jpg Tip are three viewing Slide Speed options: Fast, Normal, Slow, and Off. Press 1/2 to highlight the Slide There Speed then press 3/4 to select the option you want to use, and press SELECT/ENTER. To stop viewing 5 The JPEG menu at any other time, press STOP (x). appears. 31 OPERATION Programmed Playback Programmed Playback CD MP3 with Audio CD VCD2.0 WMA function enables you to store your favorite tracks from any disc in the player memory. Program Program ote On a setup Video CD with PBC, you must set PBC to Off on the menu to use the Program function. See page 19. contain 30 tracks. can Press PROGRAM 1 with Video CD Programmed Playback and MP3/WMA Disc The VCD1.1 mode to enter the during playback or in Program Edit mode. the stop E The mark will appear to the right of the word on the right side of the menu screen. Program Insert Video CD and close the tray. 1 2 Press PROGRAM while The VCD Program menu playback Program VCD is stopped. will appear. E TRACK 1 TRACK 2 TRACK 3 ote TRACK 4 Press PROGRAM to exit the E the mark will Program TRACK 5 Edit mode; TRACK 6 TRACK 7 disappear. Clear All TRACK 8 Select 2 place a track, then press SELECT/ENTER to the selected track on the Program list. step 3 Repeat Program 2 to place additional tracks on ote the Press RETURN PROGRAM to exit the or Program menu. list. TRACK 1 TRACK 12 TRACK 2 TRACK 8 TRACK 3 TRACK 10 TRACK 4 TRACK 3 Program MP3 WMA E Program CD 3 E FILE 8 FILE 1 FILE 2 FILE 2 FILE 4 FILE 3 TRACK 6 TRACK 7 FILE 7 Clear All Audio CD Clear All FILE 8 00:00 NORM. MP3/WMA menu OFF 3 The from resume normal "PROG" indicator disappears in the display window. menu Repeat Programmed Press 2. 4 To To repeat the track programmed track you selected last is highlighted on Tracks currently playing, Repeat icon and "TRACK" appears The press REPEAT. on the menu the program list. screen. Press 3/4 to select the track you want to start To repeat all tracks on the program list, press REPEAT a second time. 5 playing. Press TITLE to to the next page. Press DISC MENU to move to the previous page. move Press PLAY 6 Playback begins(H) Playback stops after all of the tracks have played once. 7 resume Repeat icon and "ALL" appears on the menu screen. Repeat mode, press REPEAT a third time. The Repeat icon and "OFF" appears on the menu screen. The To cancel to start. in the order in which you programmed the tracks and "PROG." appears on the menu screen. To normal on the Program list playback from programmed playback, press PROGRAM. a track of CD (or MP3/WMA) Select Erasing a Track from Program MP3/WMA disc Program E The during playback (Audio CD and only) or in the stop mode to enter the Edit mode. mark will appear. to the move Program programmed tracks/files or are cleared when the the disc is removed. erase 4 Press CLEAR. Erasing power is turned off list. 3 Use 3/4 to select the track that you wish to from the Program list. The track will be erased from the ote List 1 Press PROGRAM 2 Press 2 to list and then press SELECT/ENTER. "PROG" indicator disappears in the display window. The with left. playback 4 programmed playback, press PROGRAM. FILE 6 STER. on FILE 3 FILE 5 0: 56: 18 "Programmed Playback FILE 4 TRACK 5 TRACK 8 Follow steps 2-6 of Audio CD and MP3/WMA disc" 1 Follow List" as the Program list. Complete Program steps 1-2 of "Erasing a List Track from Program above. 2 Use 3/4 to select "Clear All", then press SELECT/ENTER. The complete Program for the disc The programs 32 are will be erased. also cleared when the disc is removed. Troubleshooting Check the following guide for the possible cause of a before problem contacting service. Cause Symptom Correction No power. The power cord is disconnected. Plug the power securely. The power is on, but the DVD+VCR does not work. No disc is inserted. No tape is inserted. Insert a disc or tape. (Check that the disc or tape indicator in the display No The TV is not set to receive DVD+VCR picture. window is signal output. cord into the wall outlet lit.) Select the appropriate video input mode on the TV so the picture from the DVD+VCR appears on the TV screen. TV/VCR mode for DVD+VCR is set to Press the TV/VCR button TV. control repeatedly to choose VCR mode. TV indicator disappears in the display window. The video cable is not connected Connect the video cable on the remote securely. securely. No sound. The connected TV power is turned off. Turn The equipment connected with the audio cable is not set to receive DVD+VCR signal output. Select the correct input mode on the audio receiver so you can listen to the sound from the DVD+VCR. The audio cables Connect the audio cable are not connected on the TV. securely. securely. The power of the equipment connected with the audio cable is turned off. The Digital Audio Output position. is set to the playback picture is poor. The disc is Tape heads Tape is a Clean video heads. dirty. are or was recorded Use CH/TRK (v/V) for manual tracking adjustment while tape is playing. on another VCR. The DVD+VCR does not start playback. No disc is inserted. Insert a disc or tape. (Check that the disc or tape indicator in the display window is lit.) No tape is inserted. An unplayable Digital Audio Output to the position, then turn on the DVD+VCR again by pressing POWER. Clean the disc. dirty. rental Set the correct wrong The Turn on the equipment connected with the audio cable. disc is inserted. Insert a playable disc. the disc (Check type, color system, and Regional code.) The disc is placed upside The disc is not The remote control does not work properly. placed Place the disc with the down. within the guide. playback Place the disc on the disc tray inside the guide. The disc is dirty. Clean the disc. The level is set. Cancel the Rating function the rating level. Rating The remote control is not pointed at the remote sensor of the DVD+VCR. sensor The remote control is too far from the DVD+VCR. Operate (7 m). There is an obstacle in the path of the remote control and the DVD+VCR. Remove the obstacle. The batteries in the remote control dead. Replace are This remote control use the same buttons for VCR and DVD functions (ex. PLAY). side down. or correctly change Point the remote control at the remote of the DVD+VCR. the remote control within 23 ft the batteries with new ones. When using a VCR, first press the VCR button. When using a DVD, first press the DVD button. 33 REF NC Troubleshooting (Continued) Cause Symptom Some channels Those channels are were Correction Use TUNING SET to restore channels. See "TO ADD OR ERASE CHANNELS FROM MEMORY" on page 15. deleted. skipped over when using CH/TRK (v/V) Picture and sound of Antenna broadcasting channel are weak or missing. Camcorder image is not Camcorder is off. or cables are loose. Tighten Turn camcorder shown. on or replace cable. and operate properly. Camcorder A/V connections input image via to DVD+VCR is not shown on DVD+VCR INPUT CHANNEL is not set Press INPUT to select LINE to LINE1 or LINE2. channel Clock in DVD+VCR is not set to correct time. Set clock to correct time. See the Clock" on page 15. Timer has been Reprogram Recording" (LINE1 or input LINE2). TV screen. Timer recording possible. is not programmed incorrectly. indicator does not appear after protimer. Reprogram "Setting Timer. See "Timer pages 21 and 22. on Timer. gramming indicator appears after DVD+VCR is DVD+VCR is in Timer Recording mode. This is the normal indication that the DVD+VCR is in TIMER mode. turned off. Stereo Audio Record and/or Playback is not present. TV is not Stereo-compatible. No action is possible. Broadcast program is not in stereo for- No action is possible. mat. DVD+VCR A/V Out nected to TV A/V In jacks are jacks. Make A/V connections. Stereo is available only via A/V output from DVD+VCR. not con- DVD+VCR Audio/Video Out is not selected for viewing at the TV. Select AUX DVD+VCR BROADCAST TYPE mode is Set BROADCAST TYPE mode to STEREO. See page 23-24. set to SAP or MONO. or A/V source as TV input. Moisture Condensation Moisture condensation ? When the DVD+VCR is moved from warm ? Under 34 In locations where moisture condensation may can occur: a cold place to a ? the DVD+VCR plugged into an AC power outlet help prevent condensation. with POWER On. This will place. extremely Keep occur: humid conditions. ? When condensation has occurred, wait a few hours for the DVD+VCR to dry before using it. Language Code Enter the (See appropriate 17). List code number for the initial settings "Disc Audio", "Disc Subtitle" and/or "Disc Menu" page Language Code Language Code Language Code Language Code Abkhazian 6566 Fiji 7074 Lingala 7678 Singhalese 8373 Afar 6565 Finnish 7073 Lithuanian 7684 Slovak 8375 Afrikaans 6570 French 7082 Macedonian 7775 Slovenian 8376 Albanian 8381 Frisian 7089 Malagasy 7771 Somali 8379 Amharic 6577 Galician 7176 Malay 7783 Spanish 6983 Arabic 6582 Georgian 7565 Malayalam 7776 Sudanese 8385 Armenian 7289 German 6869 Maltese 7784 Swahili 8387 Assamese 6583 Greek 6976 Maori 7773 Swedish 8386 Aymara 6588 Greenlandic 7576 Marathi 7782 Tagalog 8476 Azerbaijani 6590 Guarani 7178 Moldavian 7779 Tajik 8471 Bashkir 6665 Gujarati 7185 Mongolian 7778 Tamil 8465 Basque 6985 Hausa 7265 Nauru 7865 Tatar 8484 Bengali; Bangla 6678 Hebrew 7387 Nepali 7869 Telugu 8469 Bhutani 6890 Hindi 7273 Norwegian 7879 Thai 8472 Bihari 6672 Hungarian 7285 Oriya 7982 Tibetan 6679 Breton 6682 Icelandic 7383 Panjabi 8065 Tigrinya 8473 Bulgarian 6671 Indonesian 7378 Pashto, Pushto 8083 Tonga 8479 Burmese 7789 Interlingua 7365 Persian 7065 Turkish 8482 Byelorussian 6669 Irish 7165 Polish 8076 Turkmen 8475 Cambodian 7577 Italian 7384 Portuguese 8084 Twi 8487 Catalan 6765 Japanese 7465 Quechua 8185 Ukrainian 8575 Chinese 9072 Javanese 7487 Rhaeto-Romance 8277 Urdu 8582 Corsican 6779 Kannada 7578 Romanian 8279 Uzbek 8590 Croatian 7282 Kashmiri 7583 Russian 8285 Vietnamese 8673 Czech 6783 Kazakh 7575 Samoan 8377 Volapuk 8679 Danish 6865 Kirghiz 7589 Sanskrit 8365 Welsh 6789 Dutch 7876 Korean 7579 Scots Gaelic 7168 Wolof 8779 English 6978 Kurdish 7585 Serbian 8382 Xhosa 8872 Esperanto 6979 Laothian 7679 Serbo-Croatian 8372 Yiddish 7473 Estonian 6984 Latin 7665 Shona 8378 Yoruba 8979 Faeroese 7079 Latvian, Lettish 7686 Sindhi 8368 Zulu 9085 35 REF NC Code List Country Enter the appropriate code number for the initial setting "Country Code" (See page 19). Code Country Code Country Code Country Code AD Andorra ER Eritrea LC Saint Lucia SC Country Seychelles AE United Arab Emirates ES Spain LI Liechtenstein SD Sudan AF ET Ethiopia LK Sri Lanka SE Sweden AG Afghanistan Antigua and Barbuda FI Finland LR Liberia SG Singapore AI Anguilla FJ Fiji LS Lesotho SH Saint Helena AL Albania FK Falkland Islands LT Lithuania SI Slovenia AM Armenia FM Micronesia LU Luxembourg SJ Svalbard and Jan AN Netherlands Antilles FO Faroe Islands LV Latvia AO Angola FR France LY Libya SK Slovak AQ Antarctica FX France MA Morocco SL Sierra Leone AR Argentina (European Territory) MC Monaco SM San Marino AS American Samoa GA Gabon MD Moldavia SN Senegal AT Austria GB Great Britain MG Madagascar SO Somalia AU Australia GD Grenada MH Marshall Islands SR Suriname AW Aruba GE MK Macedonia ST Saint Tome and AZ Azerbaidjan GF Georgia French Guyana ML Mali SU Former USSR BA Bosnia-Herzegovina GH Ghana MM El Salvador Barbados GI Gibraltar MN Myanmar Mongolia SV BB SY Syria BD Bangladesh GL Greenland MO Macau SZ Swaziland BE Belgium GM Gambia MP Northern Mariana Islands TC Turks and Caicos Islands BF Burkina Faso GN Guinea MQ Martinique (French) TD Chad BG Bulgaria GP MR Mauritania TF BH Bahrain GQ Guadeloupe (French) Equatorial Guinea MS Montserrat BI Burundi GR Greece MT Malta TG Togo BJ Benin GS S. MU Mauritius TH Thailand BM Bermuda Isls. MV Maldives TJ Tadjikistan BN Brunei Darussalam GT Guatemala MW Malawi TK Tokelau BO Bolivia GU Guam MX Mexico TM Turkmenistan BR Brazil GW Guinea Bissau MY TN Tunisia BS Bahamas GY MZ TO Tonga BT Bhutan HK Guyana Hong Kong Malaysia Mozambique NA Namibia TP East Timor BV Bouvet Island HM Heard and McDonald NC New Caledonia TR Turkey BW Botswana Islands NE Niger TT Trinidad and BY Belarus HN Honduras NF Norfolk Island TV Tuvalu Georgia & S. Sandwich (USA) Mayen Islands Republic Principe French Southern Territories (French) Tobago BZ Belize HR Croatia NG Nigeria TW Taiwan CA Canada HT Haiti NI Nicaragua TZ Tanzania CC Cocos HU Hungary NL Netherlands UA Ukraine CF (Keeling) Islands Central African Republic ID Indonesia NO Norway UG Uganda CG Congo IE Ireland NP Nepal UK United CH Switzerland IL Israel NR Nauru UM USA Minor CI Ivory Coast IN India NU Niue CK Cook Islands IO British Indian Ocean NZ New Zealand US United States CL Chile Territory OM Oman UY Uruguay CM Cameroon IQ Iraq PA Panama UZ Uzbekistan CN China IR Iran PE Peru VA Vatican CO Colombia IS Iceland PF VC Saint Vincent & CR Costa Rica IT Italy PG Polynesia (French) Papua New Guinea CS Former Czechoslovakia JM Jamaica PH Philippines VE Venezuela CU Cuba JO Jordan PK Pakistan VG CV Cape Verde JP Japan PL Poland VI Virgin Islands (British) Virgin Islands (USA) CX Christmas Island KE Saint Pierre and VN Vietnam Cyprus KG Kenya Kyrgyzstan PM CY PN Pitcairn Island VU Vanuatu CZ Czech KH Cambodia6 PR Puerto Rico WF Wallis and Futuna Islands KI Kiribati PT Portugal WS Samoa DJ Republic Germany Djibouti KM Comoros PW Palau YE Yemen DK Denmark KN Saint Kitts & Nevis PY Paraguay YT DM Dominica KP North Korea QA Qatar YU Mayotte Yugoslavia DE Anguilla Kingdom Outlying Islands Miquelon City State Grenadines DO Dominican KR South Korea RE Reunion ZA South Africa DZ Algeria KW Kuwait RO Romania ZM Zambia EC Ecuador KY Cayman Islands RU Russian Federation ZR Zaire EE Estonia KZ Kazakhstan RW Rwanda ZW Zimbabwe EG Egypt LA Laos SA Saudi Arabia EH Western Sahara LB Lebanon SB Solomon Islands 36 Republic (French) Specifications General Power AC 110-240V Power 23W requirements consumption Dimensions (approx.) Mass (approx.) Operating temperature Operating humidity Signal system , 50/60 Hz 430 X 85 X 307 4.7 (16.9 mm x 3.3 x 12.1 inches) (w x h x d) kg (10.34 lbs) 5˚C to 40˚C (41˚F 104˚F) to REF NC 5 % to 90 % NTSC Inputs ANTENNA IN VHS VIDEO IN VHS AUDIO IN Antenna CATV input, 75 ohms 1 Vp-p 75 ohms, sync negative, RCA jack x 2 -6.0 dBm more than 47 ohms, RCA jack (L, R) or x 2 Outputs VIDEO OUT S-VIDEO OUT COMPONENT VIDEO OUT Audio output Audio output (digital audio) (analog audio) RF OUT VCR Channel 3 or x 1 4 Specifications Head system Timer Maximum Tape speed Tape width recording time Rewind time Antenna VHF output signal Channel coverage Frequency range Signal-to-noise ratio Dynamic range Channel separation DVD 1 Vp-p 75 ohms, sync negative (Y) 1.0 V (p-p), 75 ohms, negative sync, Mini DIN 4-pin (C) 0.3 V (p-p) 75 ohms (Y) 1.0 V (p-p), 75 ohms, negative sync, RCA jack x 1 (Pb)/(Pr) 0.7 V (p-p), 75 ohms, RCA jack x 2 0.5 V (p-p), 75 ohms, RCA jack x 1 2.0 Vrms (1 KHz, 0 dB), 330 ohms, RCA jack (L, R) x 1 Four head helical scan azimuth system with AM, PM SP: 33.35 mm/sec, LP: 16.67 mm/sec, EP: 11.12 mm/sec 12.7 mm 12-hour display type SP: 2 HOURS (T-120), EP: 6 HOURS (T-120)/8 HOURS (T-160) (T-120) 75 ohms (VHF/UHF) Channel 3 or 4 (Switchable) VHF: 2-13, UHF: 14-69, CATV: 1-125 (4A, A-W, W+1 W+84, A-5 About 3 minutes - - A-1) 20Hz to 20kHz More than 43dB More than 88 dB More than 60 dB Specifications Laser system Frequency response Semiconductor laser, DVD (PCM 96 kHz): wavelength 650 nm 8 Hz to 44 kHz, DVD (PCM 48 kHz): 8 Hz to 22 kHz CD:8Hzto20kHz Signal-to-noise ratio Harmonic distortion Dynamic range (ANALOG OUT jacks only) More than 100dB Less than 0.008% More than 95 dB (DVD/CD) Accessories: Video cable Design x and 1, Audio cable specifications x 1, RF 75-ohm Coaxial Cable are subject to change without x 1, Remote control prior x 1, Batteries (AAA) x 2 notice. 37 P/NO: 3834RM0054E
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project