LG | MCV903-A0U | Owner's Manual | LG MCV903-A0U Owner's Manual

LG MCV903-A0U Owner's Manual
LA1_MCV903_ENG_MFL40968703
ENGLISH
MODEL : MCV903 (MCV903-A0U, MCS903S/F, MCS903W/AW)
Safety Precaution
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE
COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead symbol within an equilateral triangle is
intended to alert the user to the presence of uninsulated dangerous voltage
within the product’s enclosure that may be of sufficient magnitude to constitute
a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the product.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT
EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
WARNING: Do not install this equipment in a confined space such as a book case or
similar unit.
CAUTION: Do not block any ventilation openings. Install in accordance with the
manufacturer's instructions.
Slots and openings in the cabinet are provided for ventilation and to ensure reliable
operation of the product and to protect it from over heating. The openings should be
never be blocked by placing the product on a bed, sofa, rug or other similar surface.
This product should not be placed in a built-in installation such as a bookcase or rack
unless proper ventilation is provided or the manufacturer's instruction has been
adhered to.
CAUTION:
This product employs a Laser System.
To ensure proper use of this product, please read this owner’s manual carefully and
retain it for future reference. Should the unit require maintenance, contact an authorized
service center. Use of controls, adjustments or the performance of procedures other than
those specified herein may result in hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try to open the enclosure. Visible
laser radiation when open. DO NOT STARE INTO BEAM.
2
CAUTION: The apparatus should not be exposed to water (dripping or splashing) and
no objects filled with liquids, such as vases, should be placed on the apparatus.
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon a dedicated circuit;
That is, a single outlet circuit which powers only that appliance and has no additional
outlets or branch circuits. Check the specification page of this owner's manual to be
certain.
Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets,
extension cords, frayed power cords, or damaged or cracked wire insulation are
dangerous. Any of these conditions could result in electric shock or fire. Periodically
examine the cord of your appliance, and if its appearance indicates damage or
deterioration, unplug it, discontinue use of the appliance, and have the cord replaced
with an exact replacement part by an authorized servicer.
Protect the power cord from physical or mechanical abuse, such as being twisted,
kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs,
wall outlets, and the point where the cord exits the appliance.
To disconnect power from the mains, pull out the mains cord plug. When installing the
product, ensure that the plug is easily accessible.
There is so much your Hi-Fi system can do
Contents
About Player
About Remote control
Setting up
Listening to CDs
Listening to the radio
Listen to cassette tapes
Tape Recording
Playing music using USB
USB direct Recording
About MP3/WMA
Listening to music from your portable player
USER EQ
Natural EQ
VSM (Virtual Sound Matrix)
VOCAL FADE
Setting the Clock
Use your player as an alarm clock
Fall asleep while listening to your player
DEMO
Troubleshooting
Specifications
4
5
6
7
7
8
8
9
9 - 10
10
10
10
10
10
10
11
11
11
11
12
13
Put the battery in the remote control
Make sure that the + (plus) and - (minus) on
the battery (size AAA) match those on the
remote control.
The making of unauthorized copies of copy-protected material,
including computer programs, files, broadcasts and sound
recordings, may be an infringement of copyrights and constitute
a criminal offence. This equipment should not be used for such
purposes.
Be responsible
Respect copyrights
Before connecting, operating or adjusting this product, please read this instruction booklet carefully
and completely.
3
About Player
DISPLAY WINDOW
Choose a desired CD (see Listening to CDs)
TIMER (see Use your player as an alarm clock)
With the TIMER function you can turn CD, tape,
USB play and TUNER reception on or off at a
desired time.
Power on/off
CLOCK (see Setting the Clock)
For setting the clock and checking the time.
To select TUNER (FM or AM) fuction
eXtreme Dynamic Sound System
Reinforce the treble, bass and surround sound
effect.
MP3 OPT
Optimizes compressible MP3 files so that it
improves the bass sound.
Look for radio stations automatically
DEMO
Press DEMO in power off state to demonstrate
the function on display window.
RVS MODE (see Listen to cassette tapes)
SET (see Setting the clock)
Confirms the time you have selected when
setting the clock.
Z OPEN/CLOSE
You can use it when inserting or removing CDs.
Record from tape to tape
(Listen to cassette tapes)
CD to Tape Synchronized Recording
Disc tray
Skip to another track (see Listening to CDs)
Select the radio station
(see Listening to the radio)
NATURAL EQ
You can choose sound impressions.
MIC VOL.
Adjust the microphone volume by
turning MIC VOL.
Starts playback (see Listening to CDs)
Choose a ‘preset number’ for a radio
station (see Listening to the radio)
Stops playback or recording
Look for radio stations automatically
Starts or pauses recording
PORTABLE IN
For connecting a portable device and playing it
through the system’s speakers.
PORTABLE
The player can be used to play the music from
many types of portable player.
AUX
You can connect many other types of audio
or audio visual device to the system via the
auxiliary sockets (AUX IN) on the back of the
player.
PHONES
Connect a headphone plug ( 6,3 mm) into the
jack to listen to the sound through headphones.
MIC 1/MIC 2
You can sing to a music source by connecting a
microphone (not supplied) to the unit.
VOCAL FADE
When you listen to music, it reduce the vocal of
file.
4
About Remote control
NATURAL EQ
You can choose sound impressions.
Power on/off
Power save mode
Press POWER for longer than 3 seconds as the device
is powered on, you can move into power save mode.
Search for a folder of MP3/WMA files
When a CD containing MP3/WMA files in several folders is being played, press PRESET/FOLDER to select
the folder you want to play.
Choose a ‘preset number’ for a radio
station (see Listening to the radio)
VSM (Virtual Sound Matrix)
You can select the Virtual sound.
Temporarily stop the sound
Press the button again to return to the sound.
To change the functions
Change the functions among FM, AM, CD, TAPE.
Control the volume when using any function.
To change the INPUT functions
Change the functions among USB, AUX, PORTABLE.
Listen to your tracks again and again
Fall asleep while listening to your player
Press SLEEP one or more times to select delay time
between 10 and 180 minutes, after the player will
turn off.
Dimm the display light
For storing radio stations
(see Listening to the radio)
Listen to your tracks in any order
(see Listening to the CDs)
See information about your music
MP3/WMA files often come with tags. The tag gives
the Title, Artist, Album or Time information.
Stops playback or recording
Select the radio station
Search for a section within a track
Play Fast backward or Forward
Starts or pauses recording
Choose a desired CD
(see Listening to CDs)
Selecting the sound system
You can enjoy different sounds by selecting the sound
mode you want. Press LINK repeatedly, the display
changes in the following order, LINK ON →
SURROUND 1 → SURROUND 2.
Starts or pauses playback
Improve poor FM reception
This will change the tuner from stereo to mono and
usually improve the reception.
5
Setting up
Using the subwoofer
You can use the sound of the subwoofer to enhance
the bass. Press POWER on the subwoofer repeatedly, the display changes in the following order,
SUB_WOOFER ON - SUB_WOOFER OFF.
4 Fit the AM loop aerial to its stand
Connect the AM loop aerial to the player.
5 Connect the FM aerial
The reception will be at its best when the two loose ends of the
aerial are in a straight line and horizontal.
6 Plug the power plug into a wall socket
subwoofer (A)
subwoofer (B)
1 Connection of the front speakers
Connect the speaker cables to the front speaker terminals.
2 Connection of the surround speakers
Connect the speaker cables to the surround speaker terminals.
3 Connection of the subwoofer
Connect the subwoofer(A) cables to the subwoofer terminals
and the woofer system cable to the woofer system connector.
Connect the subwoofer(B) speaker cables to the subwoofer(A)
speaker terminals.
Be careful of the following
Be careful to make sure children not to put their hands or any objects into the
*speaker duct.
*speaker duct : A holl for plentiful bass sound on speaker cabinet(enclosure).
6
NOTES:
• Do not place the front/surround/subwoofer speakers by TV.
• If TV screen becomes discolored do not place front speakers
within 30cm from TV.
• Connect the speakers using the supplied speaker cables by
matching the colors of the terminals and those of the cords.
• Be sure to match the speaker cord to the appropriate terminal
on the components: + to + and – to –. If the cords are
reversed, the sound will be distorted and will lack base.
Listening to CDs
Listening to the radio
Audio CD and MP3/WMA CD can be played back in this player.
ON PLAYER
1. Open the CD door:
Z OPEN/CLOSE
2. Select the CD tray:
DISC.SKIP
3. Insert the CD: Label facing up.
4. Close the CD door:
Z OPEN/CLOSE
5. Select the CD function: The display
CD
will show the total number of tracks
(files).
6. Start the CD playing:
B
7. To stop a CD playing:
x STOP
Make sure both the FM and AM aerials are connected.
ON REMOTE
D.SKIP
FUNCTION
B/[]
x
1. Select either FM or AM:
2. Select the radio station:
3. To ‘save’ a radio station: A preset
number will show in the display.
4. To select a ‘saved’ station:
5. To confirm press: Up to 50 radio
stations can be saved.
ON PLAYER
ON REMOTE
TUN.
MULTI JOG
FUNCTION
TUN.- / TUN.+
PROGRAM/MEMO
PRESET(-)/(+)
PRESET/FOLDER
PROGRAM/MEMO
Listening to the radio - more you can do
Look for radio stations automatically
Listening to CDs - more you can do
Pause or restart a CD
Press CD PAUSE on the player or B/[] on the remote control during playback.
Press this button again to resume play.
Press bb AUTO TUN / AUTO TUN BB on the player or TUN.- / TUN.+ on the
remote control for more than 0.5 second. The tuner will scan automatically and
stop when it finds a radio station.
Delete all the saved stations
Hold bb / BB on the player or .bb/BB> on the remote control during
playback.
Press and hold PROGRAM/MEMO on the remote control for two seconds.
“ERASE ALL” shows. Press PROGRAM/MEMO on the remote control to erase
all the saved stations.
Skip to another track
Choose a ‘preset number’ for a radio station
Search for a section within a track
Use MULTI JOG on the player or .bb/BB> on the remote control.
Listen to your tracks in any order
Select a station you want by using MULTI JOG on the player or TUN.- / TUN.+
on the remote control. Press PROGRAM/MEMO, the station flashes. Press
PRESET(-)/(+) on the player or PRESET/FOLDER on the remote control to
select the preset number you want. Press PROGRAM/MEMO to save it.
Up to 20 tracks on a CD can be listened to in the order of your choice. Insert a
CD and wait for it to be read. Press PROGRAM/MEMO on the remote control,
then use MULTI JOG on the player or .bb/BB> on the remote control to
select the track. Press PROGRAM/MEMO again to save and select the next
track. Press B on the player or B/[] on the remote control. To clear your selection, press x STOP (or x ), PROGRAM/MEMO and then x STOP (or x ).
Press DUBB/CD SYNC on the player or B/[] on the remote control. This will
change the tuner from stereo to mono and usually improve the reception. Or
connect the antenna securely.
Listen to your tracks again and again
Improve poor AM reception
Press MODE repeatedly, the display changes in the following order, RPT 1 RPT DISC - RPT ALL - RANDOM - OFF.
When receiving the AM broadcast, beat noises may be occur. Press AM-NOISE
repeatedly, the display changes in the following order, AM -- NOISE ON → AM
-- NOISE OFF.
Improve poor FM reception
7
Tape Recording
Listen to cassette tapes
Cassette tapes can be played back in this player.
ON PLAYER
1. Open the tape door:
2. Insert the tape:
3. Close the tape door:
4. Select the TAPE function:
5. Start the tape playing:
6. To stop a tape playing:
ON REMOTE
Record from a CD, AUX, USB, PORTABLE or radio to
cassette
Wind the tape to the point recording starts. Use only normal tapes.
Z PUSH EJECT
ON PLAYER
Z PUSH EJECT
TAPE
FUNCTION
b or B
x STOP
B/[]
x
Listen to cassette tapes - more you can do
To Play Fast backward or Forward
After pressing bb/BB on the player during playback, or stop, press B at a point
you want.
DUBBING
This function shows how to record from tape to tape. Press TAPE on the player
or FUNCTION on the remote control to select tape function.
• TAPE 1 - Insert a playback tape to dub.
• TAPE 2 - Insert a blank tape.
Press DUBB on the player as shown below. To stop dubbing, press x STOP on
the player.
1. Open the TAPE 2 door:
Insert a blank tape:
2. Close the TAPE 2 door:
3. Select a mode in which you want
to record: Start playing the source
you want to record.
4. Puts the unit in standby more for
recording: The display changes in
the following order, “USB REC →
TAPE REC”.
5. Select the “TAPE REC”:
Start recording.
6. To stop a Recording:
NOTE: In case you use the tape for the first time push the Z PUSH EJECT to
open the tape door and then remove the cushion in it.
8
Z PUSH EJECT
CD, TUN.,
PORTABLE/AUX
or USB
REC./[]
FUNCTION
or
INPUT
REC
REC./[]
REC
x STOP
x
CD to Tape Synchronized Recording
The CD synchro recording function dubs a complete CD and programmed
titles automatically into a cassette.
RVS MODE (AUTO REVERSE DECK - TAPE2 )
You can set the tape to play one side
, both sides
, or both sides six
times
, by pressing RVS MODE one or more times.
ON REMOTE
Z PUSH EJECT
ON PLAYER
1. Open the TAPE 2 door:
Insert a blank tape.
2. Close the TAPE 2 door:
3. Select the CD function:
4. Start the Recording:
The synchronized recording is
started automatically after about 7
seconds.
5. To stop a Recording:
ON REMOTE
Z PUSH EJECT
Z PUSH EJECT
CD
CD SYNC
FUNCTION
x STOP
x
Playing music using USB
The advantage of connecting your portable USB player through the
system’s USB port is that the portable device can be controlled from the
system.
ON PLAYER
1. Connect the portable player to the
system using a USB cable (not
supplied):
USB
2. Select the USB function: The display will show READ, followed by the
number of files displayed.
3. Start the USB playing:
B
4. To stop a USB playing:
x STOP
5. Before disconnecting the portable
TUN., CD,
USB player, change to any other
TAPE or
function by pressing:
PORTABLE/AUX
6. Remove the USB player:
USB direct Recording
Record FM, AM, TAPE, AUX or PORTABLE source
to USB
Connect USB to the player before recording.
ON REMOTE
INPUT
B/[]
x
FUNCTION
or
INPUT
Listen to your tracks again and again
Press MODE repeatedly, the display changes in the following order, RPT 1 RPT ALL - RANDOM - OFF.
NOTES:
• Some portable devices are not compatible with this system.
• When various cards are connected to the Memory Card Reader, the first
detected card is recognized.
• Do not extract the USB device in operating.
• A back up demands to prevent a data damage.
• If you use a USB extension cable or USB hub, the USB device might not be
recognized.
• A device using NTFS file system is not supported (Only the FAT (16/32) file
system is supported.).
• The USB function of this unit does not support all USB devices.
• Digital camera and mobile phones are not supported.
• This unit is not supported when the total number of files is 1000 or more.
1. Select a mode in which you want
to record: Start playing the source
you want to record.
2. Puts the unit in standby more for
recording: The display changes in
the following order, “USB REC →
TAPE REC”.
3. Select the “USB REC”:
Start recording.
4. To stop a Recording:
ON PLAYER
ON REMOTE
TUN., TAPE
or
PORTABLE/AUX
REC./[]
FUNCTION
or
INPUT
REC
REC./[]
REC
x STOP
x
Record Audio CD source to USB
You can record one desired track or all of the music tracks in Audio CD
to USB.
1. Select the CD function:
2. Select the track:
3. Puts the unit in standby more for
recording: The display changes in
the following order, “USB REC →
TAPE REC”.
4. Select the “USB REC”:
Start recording.
5. To stop a Recording:
ON PLAYER
ON REMOTE
CD
MULTI JOG
REC./[]
FUNCTION
.bb/BB>
REC
REC./[]
REC
x STOP
x
NOTES:
• Remove USB while recording, the recorded file may not be saved.
• When you select CD function, and then press REC./[] (REC) as not selecting
any tracks, all music files in CD are recorded.
9
Press REC./[] on the player or REC on the remote control for longer than 3 seconds, you can select bit rate. Use MULTI JOG on the player or .bb/BB>
on the remote control to select the bit rate. And REC./[] or REC again to select the
recording speed. Use MULTI JOG or .bb/BB> to select a desired recording speed and REC./[] or REC again to finish recording.
- X 1 SPEED (96kbps, 128kbps, 192kbps, 256kbps)
: You can listen to music while recording it.
- X 2 SPEED (Only 96kbps, 128kbps)
: You can just recording the music file. (Only Audio CD)
About MP3/WMA
MP3/WMA Disc compatibility with this unit is limited as follows:
• Sampling Frequency : 8 - 48 kHz (MP3), 32 - 48 kHz (WMA)
• Bit rate : 8 - 320 kbps (MP3), 48 - 320 kbps (WMA)
• CD-R physical format should be “ISO 9660”
• If you record MP3/WMA files using the software which cannot create a FILE
SYSTEM, for example “Direct-CD” etc., it is impossible to playback MP3 files.
We recommend that you use “Easy-CD Creator”, which creates an ISO 9660
file system.
• Do not use special letters such as “/ : * ? “ < >”etc.
• Even if the total number of files on the disc has more than 1000, it will only be
shown up to 999.
USER EQ
You can listen to music with the desired sound effect (BASS, MIDDLE
and TREBLE).
ON PLAYER
1. Select a “USER EQ”:
2. When “USER EQ” is displayed, press :
3. Select the sound effect you want among BASS,
MIDDLE or TREBLE:
4. Adjust sound level (MIN, -4 to +4, MAX) :
5. Repeat the steps from 3 to 4 to set other sound
effect :
6. Press :
USER EQ
SET
PRESET (-)
or PRESET (+)
MULTI JOG
SET
Natural EQ
You can choose sound impressions. Use NATURAL EQ on the player or EQ on
the remote control the display changes in the following order, NORMAL →
NATURAL → REGUETON → SAMBA → SALSA →AUTO -- EQ (Only MP3/WMA
file) → POP → CLASSIC → ROCK → JAZZ.
VSM (Virtual Sound Matrix)
Listening to music from your portable
player
The player can be used to play the music from many types of portable player.
ON PLAYER
1. Connect the portable player by
plugging the unit into PORTABLE IN
on the front of the player.
2. Turn the power on:
3. Select the PORTABLE function:
4. Turn the portable player on and
start it playing:
10
ON REMOTE
You can select the Virtual sound. Press VSM on the remote control to set the
virtual sound.
• BYPASS: Software with multichannel surround audio signals is played according to the way it was recorded.
• ON STAGE : The sound fills Concert hall.
• VIRTUAL : Realtime 3D positioned sound rendering technology with stereo
sources, optimized for stereo speakers. Listeners may experience amazing
virtual surround effects with their own multimedia players.
VOCAL FADE
1 /]]
PORTABLE
POWER
INPUT
When you listen to music, it reduce the vocal of file. Press VOCAL FADE on the
player repeatedly, the display changes in the following order, FADE ON → FADE
OFF.
Fall asleep while listening to your player
Setting the Clock
ON PLAYER
1. Press for at least 2 seconds:
2. Choose from either: AM 12:00 (for an am and pm display) or 0:00 (for a 24 hour display).
3. Confirm your selection:
4. Select the hours:
5. Press:
6. Select the minutes:
7. Press:
CLOCK
MULTI JOG
SET
MULTI JOG
SET
MULTI JOG
SET
Use your player as an alarm clock
Press and hold TIMER on the player for two seconds. Each function, TUNER,
CD, USB, TAPE flashes for two seconds. Press SET on the player when the
function you want to be woken by is showing.
If you choose TUNER, ‘PLAY’ and ‘REC’ flash, PLAY and REC. Choose one of
them. If you choose TUNER and PLAY you will be shown the stations you have
saved as presets. Use MULTI JOG on the player to select the station you want,
then press SET.
You will be shown the ON TIME display. This is where you set the time you want
the alarm to go off. Use MULTI JOG on the player to change the hours and minutes and SET to save.
You will then be shown the OFF TIME display. This is where you set the time
you want the function to stop. Use MULTI JOG on the player to change the
hours and minutes and press SET to save.
Next you will be shown the volume (VOL) you want to be woken by.
Use MULTI JOG on the player to change the volume and SET to save. Switch
the system off. The clock icon shows that the alarm is set.
When the system is turned off you can check the time the alarm is set for by
pressing TIMER. You can also turn the alarm on and off by pressing TIMER. To
set the alarm to go off at a different time, switch the system on and reprogramme following the same steps as initially.
Press SLEEP on the remote control one or more times to select delay time
between 10 and 180 minutes, after the player will turn off. Press SLEEP on the
remote control repeatedly, the display changes in the following order, corresponding icons & dimmer ON → SLEEP 180 (dimmer ON) → SLEEP 150 (dimmer
ON) → SLEEP 120 (dimmer ON) → SLEEP 90 (dimmer ON) → SLEEP 80 (dimmer ON) → SLEEP 70 (dimmer ON) → SLEEP 60 (dimmer ON) → SLEEP 50
(dimmer ON) → SLEEP 40 (dimmer ON) → SLEEP 30 (dimmer ON) → SLEEP
20 (dimmer ON) → SLEEP 10 (dimmer ON) → SLEEP OFF & dimmer OFF.
Note: Whenever you press SLEEP, the LED of WOOFER is turned on/off.
DEMO
Press DEMO in power off state to demonstrate the function on display window.
Press again to cancel.
11
Troubleshooting
Symptom
No power.
Cause
The power cord is not plugged in.
Plug in the power cord.
Check whether electricity failed.
Check the condition by operating other
electronic devices.
No sound.
Check whether you select right function.
Press FUNCTION or INPUT and check
the selected function.
The unit does not start playback.
An unplayable disc is inserted.
Insert a playable disc.
The disc is dirty.
Clean the disc.
Radio stations cannot be tuned in.
The antenna is positioned or
connected poorly.
Connect the antenna securely.
Unable to record.
Record protect tabs are removed.
Cover holes on back edge of tape with
tap.
The remote control does not work
properly.
The remote control is too far from the
unit.
Operate the remote control within
about 23 ft (7 m).
There is an obstacle in the path of the
remote control and the unit.
Remove the obstacle.
The battery in the remote control is
exhausted.
Replace the battery with new one.
General
CD
RADIO
TAPE
Remote control
Designs and specifications are subject to change without notice.
12
Correction
Specifications
Player
General
Tuner
Amplifier
CD
Cassette tape player
Power supply
Power consumption
Net Weight
External dimensions (WxHxD)
Operating temperature
Operating humidity
FM Tuning Range
AM Tuning Range
Output Power
T.H.D
Frequency Response
Signal-to-noise ratio
Frequency response
Signal-to-noise ratio
Dynamic range
F.F/REW Time
Frequency Response
Signal to Noise Ratio
Channel Separation
Erase Ratio
Refer to main label.
Refer to main label.
8,45 kg
170 x 240 x 260 mm
5 oC to 35 oC
5% to 85 %
87,5 - 108.0 MHz or 65 - 74 MHz, 87,5 - 108,0 MHz
522 - 1620 kHz or 520 - 1720 kHz
Front : 280 W + 280 W, Surround : 140 W + 140 W, Sub Woofer : 180 W + 180 W
10 %
42 - 20000 Hz
75 dB
40 - 20000Hz
75 dB
80 dB
120 sec (C-60)
250 - 8000 Hz
43 dB
45 dB (P/B)/45 dB (R/P)
50 dB (MTT-5511)
Speakers
Speaker Name
Type
Impedance
Frequency Response
Sound Pressure Level Rated
Input Power
Max. Input Power
Net Dimensions
Net Weight (1EA)
MCS903S
Bass Reflex 2Way 2 Speaker
16 Ω
70 - 20000 Hz
83 dB/W (1m)
140 W
280 W
205 x 432 x 286 mm
4,4 kg
MCS903F
Bass Reflex 2Way 2 Speaker
8Ω
55 - 20000 Hz
86 dB/W (1m)
280 W
560 W
270 x 432 x 326 mm
8,3 kg
MCS903AW/MCS903W
Bass Reflex 1 Way 1 Speaker
12 Ω
50 - 1500 Hz
85 dB/W (1m)
180 W
360 W
315 x 432 x 356 mm
9,8 kg
13
P/NO : MFL40968703
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising