Philips UpBeat Bluetooth headphones SHB2505WT/00 User manual

Philips UpBeat Bluetooth headphones SHB2505WT/00 User manual
SHB2505
blue
on the front panel.
blue
3
Take both headsets from the
charging case, the headset will
power on automatically, entering
pairing model and Right & Left
headset connected.
There will be a voice “Power on”
and a voice “Pairing”. Then, there
will be a voice“ Right channel” on
right headset and “Left Channel”
on left headset after paring each
other.
In right headset, it has voice
“Pairing” and LED flashes in
white and blue.
Single headset pairing
(Mono mode)
Take the right headset ("Master
device" ) from the charging case, the
earpiece will power on automatically.
There will be a voice ”Power on” from
right headset.
In right headset, it has voice
“Connected” and LED stays on
for 5 seconds on both headsets.
You can use your device to play
music or make a call.
Turn on the Bluetooth function on
your device, search for" Philips
SHB2505” tap to connect. ( Please
refer to P.6 )
Once the pairing succeed, you will
hear a voice" connected" And the
indicator light will be off.
Only Turn the “Left headset channel power on,
it cannot connect to Bluetooth device, need to
turn on “Right Channel” to pair each other.
1
Mutti-function
Take both headsets from the charging
case, the headset will power on and
reconnect automatically.
Headsets
If no device is connected, the
headset will automatically turn off
after 3 mins
headsets
Take both
headsets
from the
charging
case.
Place both
headsets
in charging
case.
automatically.
Right/Left
headset
5
3 times.
/Left
headset
headset
and
hold 2
seconds
Left
headset
and
hold 2
seconds
3
white
flash twice for
every 3 min
/Left
headset
/Left
headset
2
/Left
headset
2
Battery LED indicator on
headset status
It will show a battery indicator on
Bluetooth device after connected to
headset.
/Left
headset
white
light stays on for
2
and white
and white
will
3
Battery LED indicator on
Charging case
While charging headset, Blue LED will
light on
4 blue LED lights stay on for 75-100% power
3 blue LED lights stay on for 50-75% power
2 blue LED lights stay on for 25-50% power
1 blue LED lights stay on for 0-25% power
Battery LED indicator
on Charging case with
USB cable
While charging headset, Blue LED
status as below:
4 blue LED stay on for 70-100% power
2 blue LED stay on and 3rd LED flashes
every second for 50-75% power
1 blue LED stays on and 2nd LED
flashes every second for 25-50% power
1 blue LED flashes every second for
0-25% power
Put both headset back to charging
case. Hold and press left & right
headsets function button for 5 seconds.
Take both headsets from the
charging case, the headset will
power on automatically.
There will be a voice “Power on”
and a voice “ Pairing”.
Then, there will be a voice“ Right
channel” on right headset and
“Left Channel” on left headset
after paring each other. The LED
on Right headset flashes in
white and blue for 3 mins.
There will be a voice “Connected”
from Right Channel.
Then, the right headset LED earpiece
flashes in white and blue for 3 mins.
3
2.5
60
5.0
Put both earpieces into charging case.
Philips
How to reset pairing.
Take both headsets out of the charging
case. Press twice on both headsets
Multi-function buttons until the LED
indicator turns white, wait for about 10
seconds. You will hear “Connected”,
“Left Channel”, “Right Channel”, as
pairing successful.
put both earpieces
back to charging case for 5
seconds and thak them out.
put both earpieces back to
charging case for 5 seconds and
thak them out.
and Left
1.0
51
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement