Philips | HTS3377/51 | Owner's Manual | Philips 5.1 Home theatre HTS3377/51 User manual

Philips 5.1 Home theatre HTS3377/51 User manual
Register your product and get support at
www.philips.com/welcome
HTS3377
UK
RU
1 Important
Create MP3 audio les
4
Safety and important notice
Trademark notice
4
5
2 Your Home Theater System
7
Feature highlights
Product overview
3 Connect
Place the Home Theater System
Connect video cables
Connect speaker cables to speakers
Connect speaker to speaker stand
Connect speakers and subwoofer
Connect radio antenna
Connect audio cables/other devices
4 Get started
Insert the remote control batteries
Find the correct viewing channel
Select menu display language
Turn on Progressive Scan
Change speaker settings
Use Philips EasyLink
Select a play source
5 Play
Play a disc
Play video
Play music
Play photo
Play from USB device
Play from portable media player
Play from radio
34
7
8
11
11
12
14
14
14
15
15
34
7 Adjust sound
35
Control the volume
Select surround sound
Select a preset sound
Adjust microphone volume level
Karaoke settings
Turn off vocal (cancel voice)
35
35
35
36
36
36
8 Adjust settings
37
General setup
Audio setup
Video setup
Preferences
37
39
41
43
9 Additional Information
45
Update software
Care
45
45
18
18
19
19
20
21
22
24
Eng lish
6 Advanced features
10 Specications
46
11 Troubleshooting
48
12 Glossary
50
25
25
25
29
30
31
32
32
EN
3
Contents
Contents
1 Important
Recycling
Safety and important notice
Warning
• Risk of overheating! Never install the Home Theater
•
•
•
•
•
•
System in a conned space. Always leave a space of at
least 4 inches around the Home Theater System for
ventilation. Ensure curtains or other objects never cover
the ventilation slots on the Home Theater System.
Never place the Home Theater System, remote control
or batteries near naked ames or other heat sources,
including direct sunlight.
Only use this Home Theater System indoors. Keep this
Home Theater System away from water, moisture and
liquid-lled objects.
Never place this Home Theater System on other
electrical equipment.
Keep away from this Home Theater System during
lightning storms.
Where the mains plug or an appliance coupler is used
as the disconnect device, the disconnect device shall
remain readily operable.
Visible and invisible laser radiation when open. Avoid
exposure to beam.
This product complies with the radio
interference requirements of the European
Community.
This product complies with the requirements of
the following directives and guidelines: 2006/95/
EC, 2004/108/EC
4
EN
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
When you see the crossed-out wheel bin
symbol attached to a product, it means the
product is covered by the European Directive
2002/96/EC:
Never dispose of your product with other
household waste. Please inform yourself about
the local rules on the separate collection of
electrical and electronic products. The correct
disposal of your old product helps prevent
potentially negative consequences on the
environment and human health.
Your product contains batteries covered by the
European Directive 2006/66/EC, which cannot
be disposed of with normal household waste.
Please inform yourself about the local rules on
separate collection of batteries. The correct
disposal of batteries helps prevent potentially
negative consequences on the environment and
human health.
Trademark notice
Eng lish
Copyright notice
About Progressive Scan
Consumers should note that not all high
denition television sets are fully compatible
with this product and may cause artifacts to
be displayed in the picture. In case of 525
or 625 progressive scan picture problems,
it is recommended that the user switch the
connection to the ‘standard denition’ output.
If there are questions regarding our TV set
compatibility with this model 525p and 625p
DVD player, please contact our customer
service center.
Manufactured under license from Dolby
Laboratories. Dolby, Pro Logic and the
double-D symbol are trademarks of Dolby
Laboratories.
Important
This product incorporates copyright protection
technology that is protected by method claims
of certain U.S. patents and other intellectual
property rights owned by Macrovision
Corporation and other rights owners. Use of
this copyright protection technology must be
authorised by Macrovision Corporation, and is
intended for home and other limited viewing
uses only unless otherwise authorised by
Macrovision Corporation. Reverse engineering
or disassembly is prohibited.
DivX, DivX Ultra Certied, and associated
logos are trademarks of DivX, Inc. and are used
under license.
Ofcial DivX® Ultra Certied product.
Plays all versions of DivX ® video (including
DivX ® 6) with enhanced playback of DivX®
media les and the DivX® Media Format.
Plays DivX® video with menus, subtitles and
audio tracks.
Manufactured under license under U.S. Patent
#’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762;
6,487,535 & other U.S. and worldwide patents
issued & pending. DTS and DTS Digital
Surround are registered trademarks and the
DTS logos and Symbol are trademarks of DTS,
Inc. © 1996-2008 DTS, Inc. All Rights Reserved.
ENERGY STAR and the ENERGY STAR mark
are registered U.S. marks.
EN
5
Windows Media and the Windows logo
are trademarks, or registered trademarks of
Microsoft Corporation in the United States
and/or other countries.
HDMI, and HDMI logo and High-Denition
Multimedia Interface are trademarks or
registered trademarks of HDMI licensing LLC.
The USB-IF Logos are trademarks of Universal
Serial Bus Implementers Forum, inc.
LASER RADIATION
DO NOT VIEW DIRECTLY
WITH OPTICAL INSTRUMENTS
CLASS 1M LASER PRODUCT
6
EN
Congratulations on your purchase, and
welcome to Philips! To fully benet from the
support that Philips offers, register your product
at www.philips.com/welcome.
Feature highlights
Video upscaling to 1080p
Enjoy watching discs in the highest picture
quality available for your HDTV. This Home
Theater System offers full high-denition video
playback up to 1080p resolution that provides a
highly detailed picture and increased sharpness
that delivers a more true-to-life picture for an
amazing viewing experience.
Philips EasyLink
Your Home Theater System supports
Philips EasyLink, which uses the HDMI CEC
(Consumer Electronics Control) protocol.
EasyLink-compliant devices that are connected
through HDMI connectors can be controlled by
a single remote control.
Eng lish
Hi speed USB 2.0 Link and MP3 link
Simply plug your USB device into the USB jack
to play your MP3/WMA/JPEG/DivX les; or
plug your portable media player to the MP3
LINK jack to enjoy the music play in superb
sound quality.
Sync the audio output with the video play
Synchronize audio and video by delaying the
audio output if the video signal sent to the TV is
slower than the audio streams.
Create MP3 les
Convert your favorite audio tracks from an
audio CD into MP3 format. The created MP3
les are saved in your USB device.
Screen Fit
View the movie in full screen display on any TV.
Karaoke scoring function
Karaoke scoring gives a score and a comment
for each performance. Have your singing
performance scored for even more karaoke fun
at home!
Region codes
You can play discs with the following region
codes.
Note
• Philips does not guarantee 100% interoperability with
all HDMI CEC devices.
Listen to rich uncompressed multi-channel
surround sound
This Home Theater System supports 5.1
channels of uncompressed audio that delivers
a real-to-life sound experience as if you are
listening to it live.
DVD region code
Countries
Europe
Russia
EN
7
Your Home Theater System
2 Your Home
Theater System
Product overview
Main unit
h IR sensor
• Detects signals from the remote
control. Point the remote control at
the IR sensor.
i VOL
• Increases or decreases volume.
j MP3 LINK
• Connects a portable audio player
a b c d e f g h ijkl
k MIC
• Connects a microphone.
l
•
a
(Standby-On)
• Turns on the Home Theater System
or switches to standby mode.
b Disc compartment
c
(Open/Close)
• Opens or closes the disc
compartment.
d
•
•
e
(Play/Pause)
Starts, pauses or resumes disc play.
In radio mode, automatically tunes
radio stations during rst-time setup.
(Stop)
• Stops disc play.
• In radio mode, erases the current
preset radio station.
f SOURCE
• Selects a media to play or listen to
audio from the connected device.
g Display panel
• Displays the current status or disc
information.
8
EN
(USB)
Connects a USB supported device.
e
•
•
a
o
p
b
c
d
e
q
r
s
t
u
•
f
f
g
h
i
•
•
l
m
n
h
(Navigation buttons)
Navigates through the menus.
Press left and right for fast backward
or forward search.
In radio mode, press up and down to
tune the radio frequency.
In radio mode, press left or right to
start auto search.
INFO
• For discs, displays information about
the current status or the disc.
• For slideshows, displays a thumbnail
view of photo les.
g
j
k
v
w
•
SETUP
Accesses or exits the setup menu.
Eng lish
•
Your Home Theater System
d
Remote Control
(Play/Pause)
Starts, pauses or resumes disc play.
In radio mode, automatically tunes
radio stations during rst-time setup.
(Stop)
• Stops disc play.
• In radio mode, erases the current
preset radio station.
i SURR (Surround Sound)
• Switches to supported surround
sound or stereo sound.
a
b
(Standby-On)
• Turns on the Home Theater System
or switches to standby mode.
• Press and hold to turn off the Home
Theater System and all HDMI CEC
compliant devices.
(Open/Close)
• Opens or closes the disc
compartment.
c PROGRAM / REPEAT
• In radio mode, resets the list of preset
stations: press to manually reset; press
and hold to automatically reset.
• Selects or turns off repeat or shufe
mode.
j AUDIO SYNC
• Selects an audio language or channel.
• Press and hold to access the setting
for audio sync, then press VOL +/- to
set the audio delay time.
k Numeric buttons
• Selects an item to play.
l SUBTITLE
• Select DVD or DivX subtitle
languages.
m VOCAL
• Changes the audio channel of a
karaoke disc.
n MIC (VOL +/-)
• Increases or decreases microphone
volume.
EN
9
o Source buttons
• AUDIO SOURCE: Selects an audio
input source.
• RADIO: Switches to FM band.
• USB: Switches to the USB source.
• DISC: Switches to the disc source.
p OK
• Conrms an entry or selection.
q
BACK
• Returns to a previous screen.
• For DVD, goes to the title menu.
• For VCD version 2.0 or SVCD with
PBC turned on, returns to the menu
during playback.
r
/
•
s
(Previous/Next)
Skips to the previous or next title,
chapter, or track.
(Mute)
• Mutes or restores audio output.
t VOL +/• Increases or decreases volume.
u SOUND
• Selects a predened sound effect.
v ZOOM / CREATE MP3
• Zooms in or out of the picture.
• Accesses the menu to create MP3.
w KARAOKE
• Accesses or exits the karaoke menu.
10
EN
Make the following connections to use your
Home Theater System.
Basic connections:
• Video
• Speakers and subwoofer
• Power
Optional connections:
• Radio antenna
• Audio
• Audio from TV
• Audio from cable box/recorder/game
console
• Other devices
• Portable media player
• USB device
•
•
Place the Home Theater System where it
cannot be pushed, pulled over or knocked
down. Do not place it in an enclosed
cabinet.
Be sure that you have full access to the
power cord for easy disconnection of the
Home Theater System from the power
supply.
FRON
T
LEFT
REAR
LEFT
REAR
RIGHT
Note
• Refer to the type plate at the back or bottom of the
•
product for identication and supply ratings.
Before you make or change any connections, ensure
that all the devices are disconnected from the power
outlet.
Tip
• Different types of connectors may be used to connect
this product to your TV, depending on availability and
your needs. A comprehensive interactive guide to
help you connect your product is available at www.
connectivityguide.philips.com.
Eng lish
Place the Home Theater
System
CENT
ER
FRON
T
RIGH
T
SUB
WO
OFE
R
1
Place this Home Theater System near the
TV.
2
Place the speakers system at normal
listening ear-level and directly parallel to
the listening area.
3
Place the subwoofer at the corner of the
room or at least 3 feet away from the TV.
Tip
• To avoid magnetic interference or unwanted noise,
never place this Home Theater System too close to any
radiation devices.
EN
11
Connect
3 Connect
Connect video cables
Option 1: Connect to the HDMI jack
Connect this Home Theater System to TV to
view disc play. Select the best video connection
that the TV can support.
• Option 1: Connect to the HDMI jack (for a
HDMI, DVI or HDCP-compliant TV).
• Option 2: Connect to the component
video jacks (for a standard TV or
Progressive Scan TV).
• Option 3: Connect to the video (CVBS)
jack (for a standard TV).
Note
HDMI OUT
HDMI IN
1
• You must connect this Home Theater System directly
to a TV.
Connect an HDMI cable (not supplied)
to the HDMI OUT jack on this Home
Theater System and the HDMI input jack
on the TV.
Note
• If your device supports HDMI CEC, you can control
compliant devices with a single remote control. (see
‘Get started’ > ‘Use Philips EasyLink’).
Tip
• If the TV has a DVI connection only, connect via a
•
•
12
EN
HDMI/DVI adaptor. Connect an audio cable for sound
output.
You can optimize the video output. (see ‘Adjust settings’
> ‘Video setup’ > [HDMI Setup]).
This type of connection provides the best picture
quality.
Eng lish
Option 3: Connect to the Video
(CVBS) jack
Connect
Option 2: Connect to the component
video jack
VIDEO
VIDEO OUT
Y
Pb
Pr
VIDEO OUT
VIDEO IN
Y
1
Pb
Pr
Connect the component video cable
(not supplied) to the Y Pb Pr jacks on
this Home Theater System and the
COMPONENT VIDEO input jacks on the
TV.
• If a progressive scan TV is used, you
may turn on the progressive scan
mode. (see ‘Get started’ > ‘Turn on
Progressive Scan’).
1
Connect a composite video cable to the
VIDEO jack on this Home Theater System
and the VIDEO input jack on the TV.
Note
• The video input jack on the TV might be labeled as A/V
IN, VIDEO IN, COMPOSITE or BASEBAND.
• This type of connection provides standard picture
quality.
Note
• The component video input jack on the TV might be
labeled as Y Pb/Cb Pr/Cr or YUV.
• This type of connection provides good picture quality.
EN
13
Connect speaker cables to
speakers
Connect speakers and
subwoofer
For the rear speakers only
1
Connect the speaker cables to the
matching color jacks on the speakers (or
speaker stands).
Connect speaker to speaker
stand
For the rear speakers only
1
Connect the speakers and subwoofer to
the matching jacks on the Home Theater
System.
Note
• Ensure that the colors of the plugs and jacks are
matched.
1
Attach the speakers to the speaker stands
and secure the position with screws.
14
EN
FM (75 Ω)
Eng lish
Connect audio cables/other
devices
Route the audio from other devices to this
Home Theater System to enjoy audio play with
multi-channel surround capabilities.
ANTENNA
Connect audio from TV
(also used for EasyLink control)
1
Connect the FM antenna to the FM75
jack on this Home Theater System
(for some models, this cable is already
connected).
2
Extend the FM antenna and x its ends to
the wall.
Tip
• For better FM stereo reception, connect to an external
AUX 1
AUDIO IN
FM antenna.
AUDIO OUT
1
Connect the audio cables (not supplied) to
the AUDIO IN-AUX1 jacks on the Home
Theater System and the AUDIO output
jacks on the TV.
Note
• To listen to the audio output from this connection,
press AUDIO SOURCE repeatedly until ‘AUX1’ is
displayed on the display panel.
EN
15
Connect
Connect radio antenna
Connect audio from cable box/
recorder/game console
Connect to coaxial jack
You can choose to connect to analog or digital
jack depending on the device capabilities.
COAXIAL
Connect to analog jacks
DIGITAL IN
COAXIAL
DIGITAL OUT
AUX 2
AUX 2
AUDIO IN
1
Connect a coaxial cable (not supplied) to
the COAXIAL DIGITAL-IN jack on the
Home Theater System and the COAXIAL/
DIGITAL output jack on the device.
Note
AUDIO OUT
• To listen to the audio output from this connection,
press AUDIO SOURCE repeatedly until ‘COAX IN’ is
displayed on the display panel.
1
Connect the audio cables (not supplied) to
the AUDIO IN-AUX2 jacks on the Home
Theater System and the AUDIO output
jacks on the device.
Connect to optical jack
Note
• To listen to the audio output from this connection,
OPTICAL
DIGITAL IN
press AUDIO SOURCE repeatedly until ‘AUX2’ is
displayed on the display panel.
OPTICAL
DIGITAL OUT
1
16
EN
Connect an optical cable (not supplied)
to the OPTICAL DIGITAL-IN jack on the
Home Theater System and the OPTICAL/
SPDIF output jack on the device.
Eng lish
Connect USB device
Note
• To listen to the audio output from this connection,
Connect
press AUDIO SOURCE repeatedly until ‘OPTI IN’ is
displayed on the display panel.
Connect portable media player
1
MP3
Connect the USB device to
USB jack
on this Home Theater System.
Note
1
Connect a 3.5mm stereo audio cable (not
supplied) to the MP3 LINK jack on this
Home Theater System and the phone jack
on the portable media player (such as MP3
player).
Note
• This Home Theater System can only play/view MP3,
•
Connect power cord
• To listen to the audio output from this connection,
press AUDIO SOURCE repeatedly until ‘MP3 LINK’ is
displayed on the display panel.
WMA, DivX (Ultra) or JPEG les that are stored on
such devices.
Press USB to access the content and play the les.
Warning
• Risk of product damage! Ensure that the power supply
voltage corresponds to the voltage printed on the back
or the underside of the Home Theater System.
1
Connect the power cord to the power
outlet when all the required connections
are done.
» The Home Theater System is ready to
be set up for use.
EN
17
4 Get started
Insert the remote control
batteries
Control a play source
1
Press RADIO, USB or DISC button to
select the source you wish to control.
2
Select the desired function (for example ,
).
Navigate through the menu
1
2
3
Slide the battery cover off the back of the
remote control.
Insert the 2 supplied batteries (AAA). Be
sure the + and - ends of the batteries line
up with the markings inside the case.
Slide the cover back into position.
Note
• Do not mix batteries (old and new or carbon and
alkaline, etc.).
• Remove batteries if they are exhausted or if the
remote control is not to be used for a long time.
• Batteries contain chemical substances, they should be
disposed off properly.
18
EN
1
Point the remote control directly at the
remote sensor on the Home Theater
System and select the desired function.
2
Press the following buttons on the remote
control to navigate through the on-screen
menus.
Button
OK
Action
Move up or down
Move left or right
Conrm a selection
Enter numbers
1
2
3
Press to turn on the Home Theater
System.
Note
• Skip this setting if this Home Theater System is
connected to a HDMI CEC compliant TV. It switches
automatically to the same OSD menu language as per
your TV setting.
Press DISC to switch to disc mode.
Turn on the TV and switch to the correct
video-in channel in one of the following
ways:
• Go to the lowest channel on your TV,
then press the Channel Down button
until you see the Philips screen.
• Press
SOURCE button repeatedly
on the remote control of your TV.
General Setup
Tip
• The video-in channel is between the lowest and highest
channels and may be called FRONT, A/V IN, VIDEO,
HDMI etc. See the TV user manual on how to select
the correct input on the TV.
Eng lish
Select menu display language
Get started
Find the correct viewing
channel
1
2
3
4
5
EasyLink Setup
Auto
Disc Lock
English
Display Dim
ᇓ໗ ࡩ฼
OSD Language
ɻʼ ᐥ᛽
Screen Saver
Melayu
Sleep Timer
Русский
DivX(R) VOD Code
ไทย
Press DISC.
Press SETUP.
» [General Setup] menu is displayed.
Press .
Press
to select [OSD Language] in the
menu, then press .
• The language options are different
depending on your country or
region. It may not correspond to the
illustration shown here.
Press
OK.
to select a language, then press
Tip
• You can set the default language for DVD disc menu
(see ‘Adjust settings’ > ‘Preferences’ > [Disc Menu]).
EN
19
Note
Turn on Progressive Scan
• If a blank/distorted screen is displayed, wait for 15
If the TV supports progressive scan output, you
can connect this Home Theater System and the
TV using component video connection. (see
‘Connect video cables’ > ‘Option 2: Connect to
the component video jack’).
Video Setup
TV System
On
TV Display
Screen Fit
Off
Picture Setting
HDMI Setup
Closed Caption
Progressive
1
Turn on the TV and ensure that the TV
progressive scan mode is deactivated (see
the TV user manual).
2
Switch the TV to the correct viewing
channel for this Home Theater System.
3
4
5
Press DISC.
Press
SETUP.
Press to select [Video Setup] in the
menu, then press .
6
Select [Progressive] > [On], then press
OK.
» A warning message is displayed.
7
To proceed, select [Ok] and press OK.
» The progressive setup is complete.
20
EN
seconds for the auto recover.
• If no picture displayed, turn off the progressive
scan mode as follows: 1) Press to open the disc
compartment. 2) Press . 3) Press AUDIO SYNC.
8
9
Press
SETUP to exit the menu.
You can now turn on the progressive scan
mode on the TV.
Note
• During play, when progressive scan mode is on for both
this Home Theater System and the TV, distorted picture
may display. Turn off the progressive scan feature on
both this Home Theater System and the TV.
•
Repeat the above setting for other
speakers until all the speakers output
level sounds equally balance.
To exit the menu, press SETUP.
•
Audio Setup
To set the output delay time (center and rear
speakers only)
Speakers Volume
Speakers Delay
HDMI Audio
1
CD Upsampling
Audio Sync
Select [Speakers Delay] in the menu, then
press .
Speakers Distance Setup
1
2
3
Press DISC.
Press
SETUP.
Press to select [Audio Setup] in the
menu, then press .
• If the speaker setup option is not
accessible, press twice before you
press SETUP.
2
To set the speakers level
1
Select [Speakers Volume] in the menu,
then press .
Center
0MS
Rear Left
0MS
Rear Right
0MS
Press
to set the delay time, then press
OK.
• Repeat the above setting for other
speakers until the sound output from
different speakers reach the listening
position at the same time.
• To exit the menu, press SETUP.
Tip
• Set a longer delay time if the center speaker or rear
Speakers Volume Setup
Front Left
0dB
Front Right
0dB
Center
0dB
Subwoofer
0dB
Rear Left
0dB
Rear Right
0dB
•
speaker is closer to the listening position than the front
speaker.
Allow 1ms setting for every 1 foot distance between
the speaker and the listening position.
EN
21
Eng lish
Ideally, the distance between listening position
and all the speakers should be the same. If not,
change the speaker settings based on their
distance from the listening position to obtain
the best possible surround sound.
Press
to change the volume level, then
press OK.
» The test tone is emitted from the
speaker.
Get started
2
Change speaker settings
Use Philips EasyLink
Your Home Theater System supports
Philips EasyLink, which uses the HDMI CEC
(Consumer Electronics Control) protocol.
EasyLink-compliant devices that are connected
through HDMI connectors can be controlled by
a single remote control.
Note
• Philips does not guarantee 100% interoperability with
all HDMI CEC devices.
1
Turn on the HDMI CEC operations on the
TV and other connected devices. See TVs/
devices manual for details.
2
You can now enjoy the following Philips
EasyLink controls.
22
EN
EasyLink
You can turn off or turn on all EasyLink
features.
One-touch play
When you connect your Home Theater
System to devices that support one-touch play,
you can control your Home Theater System
and the devices with one remote control. For
example, when you press Play on your Home
Theater System remote control, your TV
automatically switches to the correct channel
to show the DVD content.
To enable One-touch play, a video disc must
be placed in the disc compartment before
operation.
One-touch standby
When you connect your Home Theater
System to devices that support standby, you
can use your Home Theater System remote
control to put your Home Theater System and
all connected HDMI devices in standby mode.
You can perform one-touch standby using the
remote control from any of the connected
HDMI devices.
System Audio Control
When you connect your Home Theater
System to HDMI CEC compliant devices, your
Home Theater System can switch automatically
to play audio from the connected device.
To use one-touch audio, you must map the
audio input from the connected device to your
Home Theater System.
Audio Input Mapping
When you map the audio input correctly, this
Home Theater System switches to the audio
from the played device automatically.
Map the audio inputs to the
connected devices
Note
Eng lish
Audio Input Mapping
Aux 1
[TV]
Aux 2
[DVD 3400]
Coaxial In
other (Non-HDMI)
Optical In
• Before you start, ensure that the audio output of
Get started
the HDMI TV and other HDMI devices have been
connected to the audio input jacks on this Home
Theater System.
For example, if the TV audio is
connected to the AUX1 jack on this
Home Theater System, select [Aux1]
and map with the TV (brand name) at
the right panel.
General Setup
EasyLink Setup
EasyLink
Disc Lock
One Touch Play
Display Dim
One Touch Standby
OSD Language
System Audio Control
Screen Saver
Audio Input Mapping
6
Select the audio input of this Home
Theater System that is used to connect to
other HDMI device (e.g. AUX1, AUX2),
then press .
7
Select the correct connected device, then
press OK.
» Repeat steps 5~7 to map other
connected devices.
8
Press
Sleep Timer
DivX(R) VOD Code
1
2
3
4
5
Press DISC.
Press SETUP.
» [General Setup] menu is displayed.
Press .
SETUP to exit the menu.
Select [EasyLink Setup], then press .
• [One Touch Play] and [One Touch
Standby] functions are turned on by
default in the factory.
Select [System Audio Control] > [On],
then press OK to start scanning devices.
» Once complete, audio input mapping
menu is displayed.
EN
23
Select a play source
On the main unit
•
Press SOURCE button repeatedly to
select: DISC > USB > FM > AUX 1 >
AUX 2 > COAX IN > OPTI IN > MP3
LINK > DISC ...
On the remote control
•
Press AUDIO SOURCE repeatedly to
switch to the connected audio source:
Display
Device connected to
AUX 1
AUX 2
COAX IN
OPTI IN
MP3 LINK
AUDIO IN-AUX1 jacks
AUDIO IN-AUX2 jacks
COAXIAL DIGITAL IN jack
OPTICAL DIGITAL IN jack
MP3 LINK jack
•
•
•
Press RADIO to switch to FM band.
Press USB to switch to USB mode.
Press DISC to switch to disc mode.
24
EN
Play video
Eng lish
5 Play
Note
Play a disc
• For video disc, playback always resumes from the
Play
point where it was last stopped. To start play from the
beginning, press while the message is displayed.
Caution
• Never place any objects other than discs into the disc
compartment.
• Never touch the disc optical lens inside the disc
compartment.
1
2
3
Press
to open the disc compartment.
Insert a disc with its label facing up.
• For double-sided disc, load the side to
play faces up.
Control video play
1
2
Play a title.
Use the remote control to control the title.
Button
Press to close the disc compartment and
start disc play.
• To view disc play, turn on the TV to
the correct viewing channel for this
Home Theater System.
• To stop disc play, press .
/
Note
• Check the types of discs supported. (see ‘Specications’
> ‘Playback media’).
• If the password entry menu is displayed, enter the
•
•
password before you can play the locked or restricted
disc.
If you pause or stop a disc for about 5 minutes, the
screen saver activates. To deactivate the screen saver,
press DISC.
After you pause or stop a disc and no buttons are
pressed within 15 minutes, this Home Theater System
automatically switches to standby mode.
/
Action
Starts, pauses or resumes disc play.
Stops disc play.
Skips to the next title or chapter.
Skips to the beginning of the
current title or chapter. Press twice
to jump to the previous title or
chapter.
Searches fast-forward (right)
or fast-backward (left). Press
repeatedly to change the search
speed.
In pause mode, slow motion
backward or forward play.
Searches slow-forward (down)
or slow-backward (up). Press
repeatedly to change the search
speed.
For VCD, only slow-forward play is
possible.
EN
25
Change video play
1
2
Play a title.
Use the remote control to change the
video play.
Button
Action
AUDIO
SYNC
SUBTITLE
Selects an audio language or
channel on a disc.
Selects the subtitle language on
a disc.
Selects or turns off repeat or
shufe mode.
Repeat options vary depending
on the disc type.
For VCDs, repeat play is only
possible if the PBC mode is
turned off.
Zooms in or out of the picture.
To pan through the zoomed
image, press the Navigation
buttons.
Displays the current status or
disc information.
You can change the video
play options here without
interrupting disc play.
REPEAT
ZOOM
INFO
Note
• Some operations may not work with some discs. See
the information accompanying the disc for details.
26
Access DVD menu
EN
1
2
Press DISC to access disc main menu.
Select a play option, then press OK.
• In some menus, press the Numeric
buttons to input your selection.
• To return to the title menu during
play, press
BACK.
The PBC (Playback Control) for VCD is
activated by default in the factory. When you
load in a VCD, the contents menu is displayed.
If the video play is slower than the audio output
(sound does not match with the pictures), you
can delay the audio output to match the video.
1
Press
to select a play option, then
press OK to start play.
• If PBC is off, it skips the menu and
starts play from the rst title.
• To return to the menu during play,
press
BACK (only possible if the
PBC mode is on).
2
Press DISC to preview the contents of the
disc.
• To exit the menu, press DISC.
1
Press and hold AUDIO SYNC until
‘AUDIO SYNC’ is displayed.
2
Within ve seconds, press VOL +/- to set
the delay time for audio output.
Select Digest Type:
Note
Track Digest
Disc Interval
• If the volume control is not used within ve seconds, it
resumes normal volume control function.
Track Interval
3
Select a preview play option, then press
OK
Quick skip play to a specic time
[Track Digest]
Plays the rst few seconds of each track in a
disc.
[Disc Interval]
Divides the total disc time by six and play the
rst few seconds of these intervals.
[Track Interval]
Divides the current track by six and play the
rst few seconds of these intervals.
This option is not available in stop mode.
Tip
Eng lish
Sync audio output with video play
Play
Access VCD menu or preview menu
1
During play, press INFO.
» The disc status menu is displayed.
2
Press
to view information, then press
OK.
• [TT Time] (title time)
• [Ch Time] (chapter time)
• [Disc Time] (disc time)
• [Track Time] (track time)
3
Press the Numeric buttons to enter the
time where you want to skip to, then press
OK.
• You can change the PBC setting (see ‘Adjust settings’ >
‘Preferences’ > [PBC]).
Note
• The options are different depending on the disc type.
EN
27
Repeat play a specic section
Play DivX® video
1
During playback, press INFO.
» The disc status menu is displayed.
2
3
Select [Repeat] in the menu, then press .
DivX video is a digital media format that retains
high quality despite a high rate of compression.
You can enjoy DivX video on this DivX®
Certied Home Theater System.
Move to [
A-B] in the menu, then press
OK to set the starting point.
1
4
Insert a disc or USB that contains the DivX
videos.
Press OK again to set the ending point.
» Repeat play starts.
2
5
Press DISC or USB.
» A contents menu is displayed.
To cancel repeat play, select [Off] and
press OK.
3
4
Select a title to play, then press
Note
• The marked section for repeat play is only possible
within a track/title.
Use the remote control to control the title.
Button
Action
AUDIO
SYNC
SUBTITLE
Selects an audio language or
channel.
Select DVD or DivX subtitle
languages.
Stops play.
For DivX Ultra video, press
this button again to display the
contents menu.
Displays DivX Ultra video
information.
View video play from different camera
angles
1
During play, press INFO.
» The disc status menu is displayed.
2
3
Select [Angle], then press .
Press the Numeric buttons to select an
angle, then press OK.
» Play changes to the selected angle.
Note
INFO
Note
• You can only play DivX videos that were rented or
•
•
• Applicable only to discs contain multi-angle scenes.
•
28
EN
.
purchased with the DivX registration code of this
Home Theater System (see ‘Adjust settings’ > ‘General
setup’ > [DivX(R) VOD Code]) .
You can play DivX video les of up to 4GB.
If the subtitle does not appear correctly, change the
character set (see ‘Adjust settings’ > ‘Preferences’ >
[DivX Subtitle]).
This Home Theater System can display up to 45
characters in the subtitle.
MP3/WMA is a type of highly compressed
audio le (les with .mp3 or .wma extensions).
1
1
2
Insert a disc or USB that contains the MP3/
WMA music.
2
Press DISC or USB.
» A contents menu is displayed.
3
4
Select a folder, then press OK.
Play a track.
Use the remote control to control the
track.
Button
Action
Starts, pauses or resumes
disc play.
Stops disc play.
Skips to the next track.
Skips to the beginning of
the current track. Press
twice to jump to the
previous track.
Selects an item to play.
Play
Control audio track play
Select a track to play, then press
.
• To return to the main menu, press
BACK or press until ‘Previous’
folder is selected, then press OK.
Note
• For disc recorded in multiple sessions, only the rst
session is played.
• This Home Theater System does not support MP3PRO
audio format.
• If any special characters are present in the MP3 track
/
REPEAT
Searches fast-forward
(right) or fast-backward
(left). Press repeatedly to
change the search speed.
Selects or turns off repeat
or shufe mode.
•
•
Eng lish
Play MP3/WMA music
Play music
name (ID3) or album name, it might not be displayed
correctly on the screen because these characters are
not supported.
Some WMA les are protected by Digital Rights
Management and cannot be played on this Home
Theater System.
Folders/les that exceed the supported limit of this
Home Theater System will not be displayed or played.
Tip
• You can select the display of data contents, view folders
or les (see ‘Adjust settings’ > ‘Preferences’ > [MP3/
JPEG Display]).
EN
29
Note
Play photo
• You may require longer time to display the disc content
Play photo as slideshow
•
This Home Theater System can play JPEG
photos (les with .jpeg or .jpg extensions).
1
Insert a disc or USB that contains the JPEG
photos.
2
Press DISC or USB.
» Slideshow begins (for Kodak disc) or
a contents menu (for JPEG disc) is
displayed.
3
Select the folder/album you want to play.
• To preview the photos in the folder/
album, press INFO.
•
•
on the TV due to the large number of songs/photos
compiled onto one disc.
If the JPEG photo is not recorded with an ‘exif ’ type
le, the actual thumbnail picture is not be shown on
the display. It is replaced by a ‘blue mountain’ thumbnail
picture.
This Home Theater System can only display digital
camera pictures according to the JPEG-EXIF format,
typically used by almost all digital cameras. It cannot
display Motion JPEG and pictures in formats other than
JPEG, or sound clips associated with pictures.
Folders/les that exceed the supported limit of this
Home Theater System are not displayed or played.
Control photo play
1
2
Play photo slideshow.
Use the remote control to control the
photo.
Button
ZOOM
•
•
•
To go to previous or next screen
display, press / .
To select a photo, press the
Navigation buttons.
To display the selected photo only,
press OK.
4
Press
to start slideshow play.
• To return to the menu, press
BACK.
30
EN
Action
Skips to the previous photo.
Skips to the next photo.
Rotates the photo clockwise.
Rotates the photo anticlockwise.
Zooms in or out of the
picture.
Play pause in zoom mode.
Stops play.
Play MP3/WMA music.
Navigate to the photo folder/album and
press OK to start slideshow play.
» Slideshow begins and continues till the
end of the photo folder or album.
» Audio continues to play till the end of
the disc.
•
•
To stop slideshow play, press .
To stop music play, press again.
/
1
2
This Home Theater System plays/views MP3,
WMA, DivX (Ultra) or JPEG les on the
following USB devices:
• digital camera that complies with the PTP
standard
• ash drive
• memory card reader
• HDD (external power source needed)
1
Connect a USB device to the
jack.
2
Press USB.
» A contents menu is displayed.
3
Select a le to play, then press
» Play starts.
•
To stop play, press
USB device.
(USB)
.
or remove the
Note
• If the device does not t into the USB jack, connect it
through a USB extension cable.
• If you connect a multiple USB card/device reader, only
one card/device can be accessed.
EN
31
Eng lish
Play MP3/WMA music les and JPEG photo
les simultaneously to create musical slideshow.
The MP3/WMA and JPEG les must be stored
on the same disc or USB device.
Play from USB device
Play
Play musical slideshow
Play from portable media
player
Simply connect your portable media player (e.g.
MP3 player) to this Home Theater System to
enjoy superb sound quality from your music
collections.
Play from radio
Check if the FM antenna has been connected
to this Home Theater System. If not, connect
the supplied FM antenna to the FM75 jack
and x its ends to the wall.
FM (75 Ω)
MP3
1
Connect a 3.5mm stereo audio cable (not
supplied) from the MP3 LINK jack on this
Home Theater System to the ‘headphone’
jack on the portable media player.
2
Press AUDIO SOURCE repeatedly until
‘MP3 LINK’ is displayed.
3
Start play on your portable media player.
• To stop play, press STOP on the
portable media player.
Note
• Control playback is only possible on the portable media
player.
• Stop play on the portable media player before you
ANTENNA
Tip
• For better FM stereo reception, connect an external
FM antenna (not supplied).
• Position the antenna as far away as possible from
your TV, VCR or other radiation source to prevent
interference.
First time tuning
When you access to radio mode for the rst
time, follow the instructions to install the radio
stations.
1
Press RADIO.
» ’AUTO INSTALL ... PRESS PLAY’ is
displayed.
2
Press
.
» All detected radio stations are stored.
switch to other play media/source.
» Once complete, it tunes to the rst
preset radio station.
•
To stop auto tuning, press
.
Note
• This Home Theater System can store up to a maximum
of 40 radio stations.
• If auto installation is not activated or less than 5 radio
stations are stored, you will be prompted to install the
radio stations again.
32
EN
Use the remote control to control the
radio.
1
2
Button
Action
Selects a preset radio station.
Tunes the radio frequency up or
down.
Press and hold this button to erase
the current radio station from the
preset list.
The preset number for other radio
stations remain unchanged.
Reinstall all the radio stations
1
2
Press RADIO.
Eng lish
1
2
Press RADIO.
Press
/ .
» It starts searching until a radio station
is detected.
3
Repeat step 2 until you tune to the radio
station you wish to store.
• To netune the radio frequency, press
/ .
4
Press PROGRAM.
» The preset station number blinks.
» If no action is carried out within 20
seconds after the above step, it exits
the preset mode.
5
Press / (or the Numeric buttons) to
select a preset number to store.
6
Press PROGRAM to conrm.
Press and hold PROGRAM for more than
5 seconds.
» All previously stored radio stations are
replaced.
Note
• Check the radio antenna connection if no stereo signal
is detected or less than 5 stations are detected during
radio installation.
EN
33
Play
Press RADIO.
Search and store radio stations
individually
Listen to radio
6 Advanced
features
4
Select the conversion options in the
[OPTIONS] panel, then press OK.
5
6
Press
Create MP3 audio les
You can convert audio CDs into MP3 audio
les with this Home Theater System. The
created MP3 audio les are saved in your USB
device.
Option
Description
[Speed]
Selects the write-to-le speed.
If [Normal] speed is selected,
music play can be heard while
creating the MP3 le.
Selects the quality level. Higher
bitrate for better sound quality
and bigger le size.
Default setting is [128kbps].
[Bitrate]
7
to access the [TRACK] panel.
Select the audio track, then press OK.
• To select another track, repeat step 6.
• To select all tracks, select [Select All]
in the menu and press OK.
• To deselect all tracks, select [Deselect
all] in the menu and press OK.
Select [Start] in the menu to convert, then
press OK.
» Once complete, a new folder is
created automatically in the USB
device to store all the new MP3 les.
•
To exit the menu, select [Exit] and
press OK.
Note
• While you convert, do not press any buttons.
• DTS CDs and copy-protected CDs cannot be
converted.
• Write-protected or password-protected USB devices
cannot be used to store MP3 les.
CREATE MP3
TRACK
OPTIONS
Speed
Normal
Track01
04:14
Bitrate
128kbps
Track02
04:17
Track03
03:58
Track04
04:51
Track05
03:53
Track06
04:09
Track07
04:38
SUMMARY
Select Track
0
Time
00:00
Start
1
2
Exit
Select All
Deselect All
Insert an audio CD. (CDDA/HDCD)
Connect the USB ash drive to
(USB)
jack on this Home Theater System.
3
During disc play, press CREATE MP3.
34
EN
Select a preset sound
Eng lish
7 Adjust sound
1
Press VOL +/- to increase or decrease the
volume.
• To mute, press .
• To restore the volume, press again
or press VOL +.
Select surround sound
1
Press SOUND repeatedly to select the
sound effect that most suitable for the
video or music you play.
Video/Music
Description
ACTION /
ROCK
Enhance low and high
range for great sounding
movie effects and
atmosphere. Great for
action movies and rock/
pop music.
Flat and pure sound
mode. Ideal for listening
to classical music and
watching live concert disc.
Clear mid and high range.
Recreates the atmosphere
of a live club with the
artist just in front of you.
Good for jazz music and
watching dramas.
Moderate mid range and
surround effects for clear
vocals and the atmosphere
of a live sports venue. It is
also ideal for video gaming.
Dynamically controlled
sound mode suitable
for watching movies at
night or for nonintrusive
background music.
CONCERT/
CLASSIC
1
Press SURR repeatedly to select the best
surround output that’s available on the disc.
Option
Description
5 CH
STEREO
Enhances the stereo channel
output by duplicating the
sound output to the center
and rear speakers. Ideal for
party music.
Multi-channel surround output:
DTS (Digital Theater Systems),
Dolby Digital, and Dolby Pro
Logic II.
Stereo sound from two front
speakers.
MULTICHANNEL/
DPLII
STEREO
Adjust sound
Control the volume
DRAMA /
JAZZ
SPORTS
NIGHT
EN
35
Adjust microphone volume
level
[Mic]
Turns on or off microphone output.
• [On] – Turns on microphone.
• [Off] – Turns off microphone.
[Echo Level]
Press
to set the echo level.
[Key]
Press
to set the pitch level that matches
your voice.
1
Connect a microphone (not supplied) to
MIC jack on this Home Theater System.
2
Turn on the microphone output. (see
‘Karaoke settings’.)
3
Press MIC (VOL +/-) to adjust the
microphone volume.
» ‘MIC XX’ is displayed.
•
Sing or speak through the microphone
to nd the desired volume level.
[Score]
Selects a karaoke rating score level.
• [Off] – No score rating display.
• [Basic] – Basic rating.
• [Intermediate] – Intermediate rating.
• [Advance] – Advance rating.
Turn off vocal (cancel voice)
1
Karaoke settings
Press VOCAL repeatedly until ‘VOICE
CANCEL’ is displayed.
Note
• You cannot cancel the voice output from MP3 or WMA
audio.
1
Turn on the TV to the correct viewing
channel for this Home Theater System.
2
Press KARAOKE.
» [Karaoke Setup Page] menu is
displayed.
3
Select an option and change the setting,
then press OK.
• To exit the menu, press KARAOKE.
36
EN
General setup
Eng lish
8 Adjust settings
General Setup
You can customize various kinds of settings as
you prefer. Refer to the following instructions to
navigate through the setup menus.
EasyLink Setup
Adjust settings
Disc Lock
Display Dim
Symbol
Options
OSD Language
Screen Saver
Sleep Timer
[General Setup]
DivX(R) VOD Code
[Audio Setup]
[Video Setup]
[Preferences]
Note
• If the setup option is grayed out, it means the setting
cannot be changed at the current state.
1
Press SETUP.
» [General Setup] menu is displayed.
2
3
4
Press .
Select an option, then press OK.
Select a setting, then press OK.
• To return to the previous menu, press
BACK.
• To exit the menu, press SETUP.
Note
• See the explanations of the above options in the
following pages.
EN
37
[EasyLink Setup]
If this Home Theater System is connected
to HDMI CEC compliant TV/devices, all
connected devices can respond to the following
commands simultaneously:
Option
Description
[EasyLink] Turns off or on all EasyLink
features.
To disable this feature, select [Off].
[One
When you press PLAY, the TV and
Touch
Home Theater System are turned
Play]
on. Disc play starts if there is a disc
in the Home Theater System.
To disable this feature, select [Off].
[One
If you press and hold STANDBY
Touch
for at least 3 seconds, the Home
Standby] Theatre System and all the HDMI
CEC devices switch to standby
simultaneously.
To disable this feature, select [Off].
[System
When you play audio that is
Audio
routed from the connected
Control] devices, this Home Theater System
switches to the corresponding
audio source automatically.
To enable this feature, select [On].
Then proceed to [Audio Input
Mapping] to scan and map all the
connected devices.
[Audio
When you map the audio input
Input
correctly, this Home Theater
Mapping] System switches to the audio from
the played device automatically.
Note
• You must turn on the HDMI CEC operations on the
•
38
TV/devices before you can enjoy the EasyLink controls.
See the TV/devices manual for details.
Philips does not guarantee 100% interoperability with
all HDMI CEC compliant devices.
EN
[Disc Lock]
Sets play restriction for a specic discs.
Before you start, place the disc in the disc
compartment (maximum 40 discs can be
locked).
• [Lock] – Restricts access to the current
disc. Once activated, a password is needed
to unlock and play the disc.
• [Unlock] – Plays all discs.
Tip
• You can set or change the password (see ‘Adjust
settings’ > ‘Preferences’ > [Password]).
[Display Dim]
Changes the brightness level of the display
panel on this Home Theater System.
• [100%] – Normal brightness.
• [70%] – Medium brightness.
• [40%] – Dimmest display.
[OSD Language]
Selects the default on-screen menu language.
Eng lish
Audio setup
Audio Setup
Speakers Volume
Speakers Delay
Adjust settings
[Screen Saver]
Turns off or on the screen saver mode. Helps to
protect the TV screen from being damaged due
to over exposure to a static image for too long.
• [On] – Sets the screen saver to appear
after 5 minutes of inactivity (for example, in
pause or stop mode).
• [Off] – Disable screen saver mode.
HDMI Audio
CD Upsampling
Audio Sync
[Sleep Timer]
Switches to standby automatically after the
preset time.
• [15 mins], [30 mins], [45 mins], [60 mins]
– Selects the count down time before the
Home Theater System switches to standby.
• [Off] – Disables sleep timer mode.
[DivX(R) VOD Code]
Displays the DivX® registration code.
Tip
• Enter this Home Theater System DivX registration
code when you rent or purchase video from www.
divx.com/vod. The DivX videos rented or purchased
through the DivX® VOD (Video On Demand)
service can be played only on the device to which it is
registered.
1
Press SETUP.
» [General Setup] menu is displayed.
2
Press
.
3
4
Select an option, then press OK.
to select [Audio Setup], then press
Select a setting, then press OK.
• To return to the previous menu, press
BACK.
• To exit the menu, press SETUP.
Note
• See the explanations of the above options in the
following pages.
[Speakers Volume]
Sets the volume level of each speaker to get
the ideal audio balance.
1) To start, press OK.
2) Select a speaker in the menu, then press
to adjust the volume level.
3) Press OK to conrm and exit.
Note
• The test tone is emitted from the speaker which you
adjust.
EN
39
[Speakers Delay]
Sets the delay time for the center and rear
speakers if they are placed closer to the
listening position, so that the sound output from
all speakers reach the listening position at the
same time.
1) To start, press OK.
2) Select a speaker in the menu, then press
to set the delay time.
3) Press OK to conrm and exit.
[CD Upsampling]
Converts the music CD to a higher sampling
rate using sophisticated digital signal processing
for better sound quality.
• [Off] – Disables CD-upsampling.
• [88.2kHz (X2)] – Converts the sampling
rate of the CDs twice as high as the
original rate.
Note
• CD upsampling is only available in stereo mode.
Note
• Allow 1ms setting for every 1 foot distance between
the speaker and the listening position.
[HDMI Audio]
Selects the HDMI audio setting when you
connect this Home Theater System and the TV
with a HDMI cable.
• [On] – Allows audio output through the
TV and the speaker system. If the audio
format on the disc is not supported, it
will be downmixed to two-channel sound
(linear-PCM).
• [Off] – Disables audio output from the
TV. The sound is only output through the
speaker system.
40
EN
[Audio Sync]
Sets the default delay time for audio output
when you play a video disc.
1) To start, press OK.
2) Select a speaker delay in the menu, then
press
to set the delay time.
3) Press OK to conrm and exit.
Eng lish
Video setup
[TV Display]
Selects one of the following display formats:
Video Setup
TV System
Picture Setting
•
HDMI Setup
Closed Caption
•
Progressive
•
1
Press SETUP.
» [General Setup] menu is displayed.
2
Press
.
3
4
Select an option, then press OK
to select [Video Setup], then press
Select a setting, then press OK.
• To return to the previous menu, press
BACK.
• To exit the menu, press SETUP.
Note
• See the explanations of the above options in the
following pages.
[TV System]
Change this setting if the video does not appear
correctly. By default, this setting matches the
most common setting for TVs in your country.
• [PAL] – For PAL-system TV.
• [NTSC] – For NTSC-system TV.
• [Multi] – For TV that is compatible with
both PAL and NTSC.
4:3 Letter Box (LB)
16:9 (Wide Screen)
[4:3 Pan Scan] – For 4:3 screen TV: fullheight display with the trimmed sides.
[4:3 Letter Box] – For 4:3 screen TV:
wide-screen display with black bars on the
top and bottom of the screen.
[16:9 Wide Screen] – For wide-screen TV:
display ratio 16:9.
[Screen Fit]
Fits the picture format to the TV screen to
enjoy watching disc play in full screen mode.
• [Select] – Displays various types of full
screen format, press OK to select a
suitable picture format that best ts to the
TV screen.
• [Off] – Returns to normal screen display.
[Picture Setting]
Selects a predened set of picture color settings
or customize the personal setting.
• [Standard] – Original color setting.
• [Bright] – Vibrant color setting.
• [Soft] – Warm color setting.
• [Personal] – Customizes the color setting.
Set the level of brightness, contrast,
sharpness/tint and color saturation, then
press OK.
EN
41
Adjust settings
4:3 Pan Scan (PS)
TV Display
Screen Fit
[HDMI Setup]
Selects the HDMI video setting when you
connect this Home Theater System and the TV
with a HDMI cable.
•
[Wide Screen Format] – Denes the wide
screen format for disc play.
Option
Description
[Superwide]
Center position
of the screen is
stretched less than
the side. Applicable
only to 720p
and above video
resolution setting.
No stretching of the
picture. Black bars
are displayed on both
sides of the screen.
Picture is displayed
according to the
format of the disc.
[4:3 Pillar Box]
[Off]
Note
• This setting is only available if you have set the [TV
Display] setting to [16:9 Wide Screen].
•
[HDMI Video] – Selects the HDMI video
output resolution that is compatible with
your TV display capability.
Option
Description
[Auto]
Detects and
selects the
best supported
video resolution
automatically.
Selects a video
resolution that is
best supported by
the TV. See the TV
manual for details.
[480i], [576i],
[480p], [576p],
[720p], [1080i],
[1080p]
Note
• If the setting is not compatible with your TV, a blank
screen appears. Wait for 15 seconds for auto recover
or switch to its default mode as follows: 1) Press .
2) Press . 3) Press ZOOM.
[Closed Caption]
Turns off or on display captions.
• [On] – Shows the sound effects in
subtitles. Applicable only to discs with
Closed Caption information included and
the TV supports this feature.
• [Off] – Disables closed caption.
[Progressive]
If the TV supports progressive scan output,
you can turn on the progressive scan mode to
enhance the picture quality. Video connection
through Component Video is required.
• [On] – Turns on progressive scan mode.
• [Off] – Disables progressive scan mode.
Tip
• There is more detailed description available (see ‘Get
started’ > ‘Turn on Progressive Scan’).
42
EN
[Subtitle]
Selects the default subtitle language for disc play.
Note
Adjust settings
• Stop disc play before you can access to [Preferences].
[Disc Menu]
Selects the language for disc menu.
Preferences
Note
Audio
• If the language you have set is not available on the disc,
Subtitle
the disc uses its own default language.
Disc Menu
• For some discs, the subtitle/audio language can only be
changed from the disc menu.
Parental
• To select the languages that are not listed in the menu,
PBC
MP3/JPEG Display
Password
select [Others]. Then check the Language Code list at
the back of this user manual and enter the respective
4-digit language code.
DivX Subtitle
1
Press SETUP.
» [General Setup] menu is displayed.
2
Press
.
3
4
Select an option, then press OK.
to select [Preferences], then press
Select a setting, then press OK.
• To return to the previous menu, press
BACK.
• To exit the menu, press SETUP.
[Parental]
Restricts access to discs that are unsuitable for
children. These types of discs must be recorded
with ratings.
1) Press OK.
2) Select a rating level, then press OK.
3) Press the Numeric buttons to enter the
password.
Note
Note
• See the explanations of the above options in the
following pages.
Eng lish
Preferences
[Audio]
Selects the default audio language for disc play.
• Rated discs above the level you set in [Parental]
require a password to be played.
• The ratings are country-dependent. To allow all discs to
play, select ‘8’.
• Some discs have ratings printed on them but are not
recorded with ratings. This function has no effect on
such discs.
Tip
• You can set or change the password (see ‘Preferences’
> [Password]).
EN
43
[PBC]
Turns off or on the content menu of VCDs/
SVCDs with PBC (playback control) feature.
• [On] - Displays index menu when you
load a disc for play.
• [Off] - Skips the menu and start play from
the rst title.
[MP3/JPEG Display]
Selects to display the folders or display all the
les.
• [View Folders] – Displays the folders of
MP3/WMA les.
• [View Files] – Displays all the les.
[Password]
Sets or changes the password for locked discs
and play restricted DVDs.
Change Password
[DivX Subtitle]
Selects a character set that supports the DivX
subtitle.
[Standard]
English, Irish, Danish,
Estonian, Finnish, French,
German, Italian, Portuguese,
Luxembourgish, Norwegian
(Bokmål and Nynorsk),
Spanish, Swedish, Turkish
[Central
Polish, Czech, Slovak,
Europe]
Albanian, Hungarian, Slovene,
Croatian, Serbian (Latin
script), Romanian
[Cyrillic]
Belarusian, Bulgarian,
Ukrainian, Macedonian,
Russian, Serbian
[Hebrew]
Hebrew
[Greek]
Greek
[Chinese(Simp)] Simplied Chinese
[Korean]
Korean
Old Password
New Password
Note
Confirm Password
OK
1) Press the Numeric buttons to enter
‘136900’ or the last set password at [Old
Password] eld.
2) Enter the new password at [New
Password] eld.
3) Enter the new password again at [Conrm
Password] eld.
4) Press OK to exit the menu.
Note
• Ensure that the subtitle le has the exact same le
name as the movie le. If for example the le name of
the movie is ‘Movie.avi’, then you will need to name the
text le ‘Movie.sub’ or ‘Movie.srt’.
[Version Info.]
Displays the software version of this Home
Theater System.
Tip
• This information is required when you want to nd out
if a newest software version is available at the Philips
website that you may download and install on this
Home Theater System.
• If you forget the password, enter ‘136900’ before you
set a new password.
[Default]
Resets all the settings of this Home Theater
System to factory default, except for [Disc
Lock], [Password] and [Parental] settings.
44
EN
Update software
To check for new updates, compare the current
software version of your Home Theater System
with the latest software version (if available) at
the Philips website.
Eng lish
Note
• Do not remove the CD-R or USB when software
updating is in progress.
8
Disconnect the power cord for a few
seconds and connect again to reboot the
system.
Care
Preferences
Caution
Disc Menu
• Never use solvents such as benzene, thinner, cleaners
Parental
PBC
MP3/JPEG Display
available commercially, or anti-static sprays intended
for discs.
Password
DivX Subtitle
Version Info.
Default
1
2
Press
SETUP.
Select [Preferences] > [Version Info.],
then press OK.
3
Write down the version number, then
press SETUP to exit the menu.
4
Go to www.philips.com/support to check
the latest software version available for this
Home Theater System.
5
If the latest software version is higher than
the software version of this Home Theater
System, download it and store onto a
CD-R or USB ash drive.
6
Insert the CD-R or USB ash drive to this
Home Theater System.
7
Press DISC or USB, then follow the
instruction on the TV to conrm update
operation.
» Once software update is complete,
this Home Theater System turns off to
standby automatically.
Clean discs
Wipe the disc with a micro bre cleaning cloth
from the centre to the edge in a straight line
movement.
Clean main unit screen
Wipe the screen surface with a micro bre
cleaning cloth.
EN
45
Additional Information
9 Additional
Information
10 Specifications
Note
• Specication and design are subject to change without
notice
Playback media
• DVD-Video, DVD+R/+RW, DVD-R/-RW,
DVD+R DL, CD-R/CD-RW, Audio CD,
Video CD/SVCD, Picture CD,
MP3-CD, WMA-CD, DivX-CD,
USB ash drive
Amplier
• Total output power:
• Home Theater mode:
1000 W RMS (6 X 167)
• Frequency response: 40 Hz ~ 20 kHz
• Signal-to-noise ratio:
> 60 dB (A-weighted)
• Input sensitivity:
• AUX: 400 mV
• SCART TO TV: 250 mV
• MP3 LINK: 250 mV
Disc
• Laser Type: Semiconductor
• Disc diameter: 12cm / 8cm
• Video decording:
MPEG1/ MPEG2 / DivX / DivX Ultra
• Video DAC: 12 bits, 108 MHz
• Signal system: PAL / NTSC
• Video S/N: 56 dB
• Audio DAC: 24 bits / 96 kHz
• Frequency response:
• 4 Hz - 20 kHz (44.1 kHz)
• 4 Hz - 22 kHz (48 kHz)
• 4 Hz - 44 kHz (96 kHz)
• PCM: IEC 60958
• Dolby Digital: IEC 60958, IEC 61937
• DTS: IEC 60958, IEC 61937
46
EN
Radio
• Tuning range: FM 87.5-108 MHz (50 kHz)
• 26 dB quieting sensitivity: FM 22 dBf
• IF rejection ratio: FM 60 dB
• Signal-to-noise ratio: FM 50 dB
• Harmonic distortion: FM 3%
• Frequency response:
FM 180 Hz~10 kHz / ±6dB
• Stereo separation: FM 26 dB (1 kHz)
• Stereo Threshold: FM 29 dB
USB
• Compatibility: Hi-Speed USB (2.0)
• Class support:
UMS (USB Mass Storage Class)
• File system: FAT12, FAT16, FAT32
Main Unit
• Power supply: 220 - 240V; ~50 Hz
• Power consumption: 180 W
• Standby power consumption: < 1 W
• Dimensions (WxHxD):
360 x 57 x 331 (mm)
• Weight: 3.01 kg
Speakers
• System: full range satellite
• Speaker impedance:
4 ohm (center), 4 ohm (Front/Rear)
• Speaker drivers:
• Center/Front/Rear: 3” full range
• Frequency response: 150 Hz ~ 20 kHz
• Dimensions (WxHxD):
• Center: 244 x 103 x 74 (mm)
• Front: 103 x 203 x 71 (mm)
• Rear: 262 x 1199 x 264 (mm)
• Weight:
• Center: 0.79 kg
• Front: 0.54 kg
• Rear: 3.38 kg
Specications
Eng lish
Subwoofer
• Impedance: 4 ohm
• Speaker drivers: 165 (6.5”) woofer
• Frequency response: 40 Hz ~ 150 Hz
• Dimensions (WxHxD):
163 x 363 x 369 (mm)
• Weight: 4.7 kg
Laser specication
• Type: Semiconductor laser GaAIAs (CD)
• Wave length:
645 - 665 nm (DVD),
770 - 800 nm (CD)
• Output power: 6 mW (DVD),
7 mW (VCD/CD)
• Beam divergence: 60 degrees.
EN
47
11 Troubleshooting
Warning
• Risk of electric shock. Never remove the casing of the
Home Theater System.
Main unit
The buttons on this Home Theater System do
not work.
•
Disconnect this Home Theater System
from the power outlet for a few minutes,
then connect again.
Picture
To keep the warranty valid, never try to repair
the system yourself.
If you encounter problems when using the
Home Theater System, check the following
points before requesting service. If the problem
remains unsolved, register your Home Theater
System and get support at www.philips.com/
welcome.
If you contact Philips, you will be asked for the
model and serial number of your Home Theater
System. The model number and serial number
are on the back or bottom of your Home
Theater System. Write the numbers here:
No picture.
•
See TVs manual for correct video input
channel selection. Change the TV channel
until you see the DVD screen.
•
Press DISC.
•
If you have changed the [TV Display]
setting, switch back to default mode:
1) Press to open the disc compartment.
2) Press .
3) Press SUBTITLE.
•
If you have changed the [Progressive]
setting, switch back to default mode:
1) Press to open the disc compartment.
2) Press .
3) Press AUDIO SYNC.
Model No. __________________________
Serial No. ___________________________
48
EN
No picture on HDMI connection.
•
Check if the HDMI cable is faulty. Replace a
new HDMI cable.
•
If this happens when you change the HDMI
video resolution, you have to switch to its
default mode:
1) Press .
2) Press .
3) Press ZOOM.
No sound.
• Ensure that the audio cables are connected
and press the correct input source (for
example, AUDIO SOURCE, USB) to
select the device you want to play.
DivX video les cannot be played.
•
Ensure that the DivX le is encoded
according to the ‘Home Theater Prole’
with the DivX encoder.
•
Ensure that the DivX video le is
complete.
No sound on HDMI connection.
•
Sound cannot transmit through HDMI
connection if the connected device is nonHDCP compliant or only DVI-compatible.
Make an analog or digital audio connection.
•
Ensure that the [HDMI Audio] setting is
turned on.
Eng lish
Play
Troubleshooting
Sound
The aspect ratio of the screen is not aligned
with the TV display setting.
• The aspect ratio is xed on the disc.
No sound from TV program.
• Connect an audio cable from the AUDIO
input on this Home Theater System to the
AUDIO output on your TV. Then press
AUDIO SOURCE repeatedly to select the
corresponding audio input source.
DivX subtitle does not display correctly.
•
Ensure that the subtitle le name is the
same as the movie le name.
•
Select the correct character set:
1) Press SETUP.
2) Select [Preferences], then press .
3) Select [DivX Subtitle], then press OK.
4) Select the character set that supports
the subtitle.
No surround sound effect from the speakers.
•
Press SURR to select a correct surround
sound setting.
•
Ensure that the source you are playing
is recorded or broadcast in surround
sound (Dolby Digital, etc).Sound cannot
transmit through HDMI connection if the
connected device is non-HDCP compliant
or only DVI-compatible. Make an analog or
digital audio connection.
The contents of the USB ash drive cannot
be read.
•
The USB ash drive format is not
compatible with this Home Theater
System.
•
Drive is formatted with different le
system which is not supported by this unit
(e.g. NTFS).
•
Maximum size of memory supported is
160GB.
EN
49
12 Glossary
H
A
HDCP
High-bandwidth Digital Content Protection.
This is a specication that provides a secure
transmission of digital contents between
different devices (to prevent unauthorized
copyright.)
Aspect ratio
Aspect ratio refers to the length to height ratio
of TV screens. The ratio of a standard TV is 4:3,
while the ratio of a high-denition or wide TV
is 16:9. The letter box allows you to enjoy a
picture with a wider perspective on a standard
4:3 screen.
D
DivX®
The DivX® codec is a patent-pending, MPEG-4
based video compression technology developed
by DivX®, Inc. It can shrink the le size of digital
video and still maintain the high visual quality.
Dolby Digital
A surround sound system developed by Dolby
Laboratories that contains up to six channels of
digital audio (front left and right, surround left
and right, center and subwoofer.)
50
EN
HDMI
High-Denition Multimedia Interface (HDMI) is
a high-speed digital interface that can transmit
uncompressed high denition video and digital
multichannel audio. It delivers high quality
picture and sound quality, completely free from
noise. HDMI is fully backward-compatible with
DVI.
As required by the HDMI standard, connecting
to HDMI or DVI products without HDCP
(High-bandwidth Digital Content Protection)
will result in no Video or Audio output.
J
JPEG
A very common digital still picture format. A
still-picture data compression system proposed
by the Joint Photographic Expert Group, which
features small decrease in image quality in
spite of its high compression ratio. Files are
recognized by their le extension ‘.jpg’ or ‘.jpeg.’
M
W
MP3
A le format with a sound data compression
system. MP3 is the abbreviation of Motion
Picture Experts Group 1 (or MPEG-1) Audio
Layer 3. With the MP3 format, one CD-R or
CD-RW can contain about 10 times more data
than a regular CD.
WMA
Windows Media™ Audio. Refers to an
audio compression technology developed by
Microsoft Corporation. WMA data can be
encoded with Windows Media player version 9
or Windows Media player for Windows XP. Files
are recognized by their le extension ‘.wma.’
MPEG
Motion Picture Experts Group. A collection of
compression systems for digital audio and video.
WMV
Windows Media Video. Refers to a video
compression technology developed by
Microsoft Corporation. WMV content can be
encoded by using Windows Media® Encoder
9 series. Files are recognised by their le
extension ‘.wmv’.
P
PBC
Playback Control. A system where you navigate
through a Video CD/Super VCD with on-screen
menus that are recorded onto the disc. You can
enjoy interactive playback and search.
PCM
Pulse Code Modulation. A digital audio
encoding system.
Progressive scan
The progressive scan displays twice the number
of frames per second than in an ordinary TV
system. It offers higher picture resolution and
quality.
EN
51
Abkhazian
6566
Afar
6565
Afrikaans
6570
Amharic
6577
Arabic
6582
Armenian
7289
Assamese
6583
Avestan
6569
Aymara
6589
Azerhaijani
6590
Bahasa Melayu
7783
Bashkir
6665
Belarusian
6669
Bengali
6678
Bihari
6672
Bislama
6673
Bokmål, Norwegian
7866
Bosanski
6683
Brezhoneg
6682
Bulgarian
6671
Burmese
7789
Castellano, Español
6983
Catalán
6765
Chamorro
6772
Chechen
6769
Chewa; Chichewa; Nyanja 7889
9072
中文
Chuang; Zhuang
9065
Church Slavic; Slavonic 6785
Chuvash
6786
Corsican
6779
Česky
6783
Dansk
6865
Deutsch
6869
Dzongkha
6890
English
6978
Esperanto
6979
Estonian
6984
Euskara
6985
6976
Faroese
7079
Français
7082
Frysk
7089
Fijian
7074
Gaelic; Scottish Gaelic 7168
Gallegan
7176
Georgian
7565
Gikuyu; Kikuyu
7573
Guarani
7178
Gujarati
7185
Hausa
7265
Herero
7290
Hindi
7273
Hiri Motu
7279
Hrwatski
6779
Ido
7379
Interlingua (International)7365
Interlingue
7365
Inuktitut
7385
52
Inupiaq
Irish
Íslenska
Italiano
Ivrit
Japanese
Javanese
Kalaallisut
Kannada
Kashmiri
Kazakh
Kernewek
Khmer
Kinyarwanda
Kirghiz
Komi
Korean
Kuanyama; Kwanyama
Kurdish
Lao
Latina
Latvian
Letzeburgesch;
Limburgan; Limburger
Lingala
Lithuanian
Luxembourgish;
Macedonian
Malagasy
Magyar
Malayalam
Maltese
Manx
Maori
Marathi
Marshallese
Moldavian
Mongolian
Nauru
Navaho; Navajo
Ndebele, North
Ndebele, South
Ndonga
Nederlands
Nepali
Norsk
Northern Sami
North Ndebele
Norwegian Nynorsk;
Occitan; Provencal
Old Bulgarian; Old Slavonic
Oriya
Oromo
Ossetian; Ossetic
Pali
Panjabi
Persian
Polski
Português
7375
7165
7383
7384
7269
7465
7486
7576
7578
7583
7575
7587
7577
8287
7589
7586
7579
7574
7585
7679
7665
7686
7666
7673
7678
7684
7666
7775
7771
7285
7776
7784
7186
7773
7782
7772
7779
7778
7865
7886
7868
7882
7871
7876
7869
7879
8369
7868
7878
7967
6785
7982
7977
7983
8073
8065
7065
8076
8084
Pushto
Russian
Quechua
Raeto-Romance
Romanian
Rundi
Samoan
Sango
Sanskrit
Sardinian
Serbian
Shona
Shqip
Sindhi
Sinhalese
Slovensky
Slovenian
Somali
Sotho; Southern
South Ndebele
Sundanese
Suomi
Swahili
Swati
Svenska
Tagalog
Tahitian
Tajik
Tamil
Tatar
Telugu
Thai
Tibetan
Tigrinya
Tonga (Tonga Islands)
Tsonga
Tswana
Türkçe
Turkmen
Twi
Uighur
Ukrainian
Urdu
Uzbek
Vietnamese
Volapuk
Walloon
Welsh
Wolof
Xhosa
Yiddish
Yoruba
Zulu
8083
8285
8185
8277
8279
8278
8377
8371
8365
8367
8382
8378
8381
8368
8373
8373
8376
8379
8384
7882
8385
7073
8387
8383
8386
8476
8489
8471
8465
8484
8469
8472
6679
8473
8479
8483
8478
8482
8475
8487
8571
8575
8582
8590
8673
8679
8765
6789
8779
8872
8973
8979
9085
53
Изделие получил в исправном состоянии.
С условиями гарантии ознакомлен и согласен
(подпись покупателя)
Внимание! Гарантийный талон недействителен без печати продавца.
ФИРМЫ - ПРОДАВЦА
ПЕЧАТЬ
Адрес и E-mail:
Телефон фирмы:
Название фирмы:
ПРОДАВЕЦ:
Дата продажи:
Серийный номер:
Модель:
БЫТОВАЯ ЭЛЕКТРОНИКА
ГАРАНТИЙНЫЙ ТАЛОН
54
1 год
Срок гарантии (исчисляется со дня передачи товара потребителю)
1 год
1 год
Телефон:
Интернет:
(495) 961-1111, 8 800 200-0880 (бесплатный звонок по России).
www.philips.ru
Любую информацию о расположении сервисных центров и о сервисном обслуживании Вы можете получить в Информационном Центре
3. Действия непреодолимой силы (стихия, пожар, молния и т.п.);
• неправильной установки и подключения изделия;
• отклонение от Государственных Технических Стандартов (ГОСТов) и норм питающих, телекоммуникационных и кабельных сетей;
• внесения несанкционированных изготовителем конструктивных или схемотехнических изменений и изменений программного обеспечения
• ремонта неуполномоченными лицами;
2. Действий третьих лиц:
1. Нарушения Потребителем правил эксплуатации, хранения или транспортировки товара
Гарантийное обслуживание не распространяется на изделия, недостатки которых возникли вследствие:
По окончании срока службы обратитесь в авторизованный сервисный центр для проведения профилактических работ и получения рекомендаций по
дальнейшей эксплуатации изделия.
Во избежание возможных недоразумений, сохраняйте в течение срока службы документы, прилагаемые к товару при его продаже (данный
гарантийный талон, товарный и кассовый чеки, накладные, инструкцию по эксплуатации (на любом носителе) и иные документы).
3 года
Срок службы (исчисляется со дня передачи товара потребителю)
Если в процессе эксплуатации изделия Вы сочтете, что параметры работы отличаются от изложенных в инструкции пользователя, рекомендуем
обратиться за консультацией в наш Информационный центр.
Условия гарантии
Объект
Изделие
Пульт дистанционного управления
При бережном и внимательном отношении изделие будет надежно служить Вам долгие годы. В ходе эксплуатации не допускайте механических
повреждений, попадания вовнутрь посторонних предметов, жидкостей, насекомых, в течение всего срока службы следите за сохранностью
идентификационной наклейки с обозначением наименования модели и серийного номера изделия.
При покупке убедительно просим Вас проверить правильность заполнения гарантийного талона. При этом серийный номер и наименование модели
приобретенного Вами изделия должны быть идентичны записи в гарантийном талоне. Не допускается внесения в талон каких-либо изменений,
исправлений. В случае неправильного или неполного заполнения гарантийного талона немедленно обратитесь к продавцу.
Компания изготовитель выражает благодарность за Ваш выбор и гарантирует высокое качество и безупречное функционирование данного изделия при
соблюдении правил его эксплуатации.
Уважаемый потребитель!
55
© 2009 Koninklijke Philips Electronics N.V.
All rights reserved.
sgpjy_906/51_02
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising