Philips | HTS9810/12 | Owner's Manual | Philips 5.1 Home theatre HTS9810/12 User manual

Philips 5.1 Home theatre HTS9810/12 User manual
Register your product and get support at
www.philips.com/welcome
HTS9810
EN
DVD Home Theatre System
5
FR
Home Cinéma DVD
51
ES
Cine en casa con DVD
97
DE
DVD Home Entertainment-System
143
NL
DVD home theatre
189
Important notes for users in U.K.
Mains plug
This apparatus is fitted with an approved 13
Amp plug. To change a fuse in this type of plug
proceed as follows:
1. Remove fuse cover and fuse.
2. Fix new fuse which should be a BS1362
5 Amp, A.S.T.A. or BSI approved type.
3. Refi t the fuse cover.
If the fitted plug is not suitable for your socket
outlets, it should be cut off and an appropriate
plug fitted in its place.
If the mains plug contains a fuse, this should have
a value of 5 Amp. If a plug without a fuse is
used, the fuse at the distribution board should
not be greater than 5 Amp.
Note: The severed plug must be disposed off to
avoid a possible shock hazard should it be inserted
into a 13 Amp socket elsewhere.
How to connect a plug
The wires in the mains lead are coloured with the
following code: blue = neutral (N),
brown = live (L).
• As these colours may not correspond with
the colour markings identifying the terminals
in your plug, proceed as follows:
• Connect the blue wire to the terminal
marked N or coloured black.
• Connect the brown wire to the
terminal marked L or coloured red.
• Do not connect either wire to the earth
terminal in the plug, marked E (or e) or
coloured green (or green and yellow).
Before replacing the plug cover, make certain
that the cord grip is clamped over the sheath of
the lead - not simply over the two wires.
Copyright in the U.K.
Recording and playback of material may require
consent. See Copyright Act 1956 and The
Performer’s Protection Acts 1958 to 1972.
2
Italia
DICHIARAZIONE DI CONFORMITA’
Si dichiara che l’apparecchio HTS9810, Philips
risponde alle prescrizioni dell’art. 2 comma 1 del
D.M. 28 Agosto 1995 n. 548.
Fatto a Eindhoven
Philips Consumer Electronics
Philips, Glaslaan 25616 JB Eindhoven,
The Netherlands
Norge
Typeskilt finnes på apparatens underside.
Observer: Nettbryteren er sekundert
innkoplet. Den innebygde netdelen er derfor
ikke frakoplet nettet så lenge apparatet er
tilsluttet nettkontakten.
For å redusere faren for brann eller elektrisk
støt, skal apparatet ikke utsettes for regn eller
fuktighet.
DK
Advarsel: Usynlig laserstråling ved åbning når
sikkerhedsafbrydere er ude af funktion. Undgå
utsættelse for stråling.
Bemærk: Netafbryderen er sekundært
indkoblet og ofbryder ikke strømmen fra
nettet. Den indbyggede netdel er derfor
tilsluttet til lysnettet så længe netstikket sidder i
stikkontakten.
S
Klass 1 laseraparat
Varning! Om apparaten används på annat
sätt än i denna bruksanvisning specificerats, kan
användaren utsättas för osynlig laserstrålning,
som överskrider gränsen för laserklass 1.
Observera! Stömbrytaren är sekundärt kopplad
och bryter inte strömmen från nätet. Den
inbyggda nätdelen är därför ansluten till elnätet
så länge stickproppen sitter i vägguttaget.
NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and
receiver.
- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician
for help.
SF
Luokan 1 laserlaite
Varoitus! Laitteen käyttäminen muulla kuin
tässä käyttöohjeessa mainitulla tavalla saattaa
altistaa käyttäjän turvallisuusluokan 1 ylittävälle
näkymättömälle lasersäteilylle.
Oikeus muutoksiin varataan. Laite ei saa olla
alttiina tippu-ja roiskevedelle.
Huom. Toiminnanvalitsin on kytketty
toisiopuolelle, eikä se kytke laitetta irti
sähköverkosta. Sisäänrakennettu verkko-osa on
kytkettynä sähköverkkoon aina silloin, kun
pistoke on pistorasiassa.
3
Manufactured under license from Dolby
Laboratories. Dolby, Pro Logic and the double-D
symbol are trademarks of Dolby Laboratories.
Manufactured under license under U.S. Patent
#’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762;
6,487,535 & other U.S. and worldwide patents
issued & pending. DTS and DTS Digital
Surround are registered trademarks and the
DTS logos and Symbol are trademarks of DTS,
Inc. © 1996-2007 DTS, Inc. All Rights Reserved.
HDMI, and HDMI logo and High-Definition
Multimedia Interface are trademarks or
registered trademarks of HDMI licensing LLC.
The USB-IF Logos are trademarks of Universal
Serial Bus Implementers Forum, Inc.
‘DCDi’ is a trademark of Faroudja, a division of
Genesis Microchip, Inc.
ENERGY STAR and the ENERGY
STAR mark are registered U.S. marks
DivX, DivX Ultra Certified, and associated logos
are trademarks of DivX, Inc. and are used under
license.
Official DivX® Ultra Certified product.
Plays all versions of DivX ® video (including
DivX ® 6) with enhanced playback of DivX®
media files and the DivX® Media Format.
Windows Media and the Windows logo are
trademarks, or registered trademarks of
Microsoft Corporation in the United States and/
or other countries.
CLASS 1
LASER PRODUCT
4
EN
LASER
•
Type
•
Wave length
•
Output Power
•
Beam divergence
Semiconductor laser
GaAIAs
650 - 660 nm (DVD)
784 - 796 nm (CD)
1.46 mW (DVD)
160 uW (CD)
60 degrees
1 Important
Safety and important notice
2 Your product
Features highlight
Product overview
3 Connect
Place the unit
Connect video cables
Connect junction box
Connect rear wireless speakers
Connect front and centre speakers to
subwoofer
Connect subwoofer
Connect other devices
Mount the DVD Home Theatre unit
6
6
7
7
8
11
11
12
13
14
14
15
15
17
25
Play from disc
Play video
Play music
Play photo
Play from USB device
Play from portable media player
Play from radio
25
26
29
30
31
32
32
6 Adjust sound
34
Control the volume
Adjust Bass/Treble
Select Ambisound
Select a preset sound effect
34
34
34
35
7 Adjust settings
36
General setup
Audio setup
Video setup
Preference Setup
36
38
40
42
8 Additional information
4 Get started
Prepare the remote control
Find the correct viewing channel
Start Ambisound setup
Optimise wireless transmission
Adjust speakers output
Activate EasyLink control
Select a play source
18
18
19
19
21
22
23
24
45
Update software
Care
Specifications
45
45
46
9 Troubleshooting
47
10 Glossary
49
EN
5
English
5 Play
Contents
Contents
1 Important
Recycle notice
EW!=\!8Y
Safety and important notice
Warning!
Risk of fire or electric shock!
• Ensure that air can circulate freely through the
•
•
•
•
•
ventilation holes on this unit. Allow at least 5~10 cm
clearance around the unit.
Never expose this unit to direct sunlight, naked
flames or heat.
Never place this unit on other electrical equipment.
Keep away from this unit during lightning storms.
Never remove the casing of this unit. Please leave all
maintenance work to qualified personnel.
Keep this unit away from water, moisture and liquidfilled objects.
Caution!
• Remove batteries if they are exhausted or if the
remote control is not to be used for a long time.
• Do not mix batteries (old and new or carbon and
These symbols on the products, packaging, and/
or accompanying documents mean that used
electrical and electronic products and batteries
should not be mixed with general household
waste. For proper treatment, recovery and
recycling of old products and used batteries,
please take them to applicable collection points,
in accordance with your national legislation and
Directives 2002/96/EC and 2006/66/EC.
By disposing of these products and batteries
correctly, you will help to save valuable
resources and prevent any potential negative
effects on human health and the environment
which could otherwise arise from inappropriate
waste handling.
For more information about collection and
recycling of old products and batteries, please
contact your local municipality, your waste
disposal service or the point of sale where you
purchased the items.
alkaline, etc.).
• Batteries contain chemical substances, they should
be disposed of properly.
• Visible and invisible laser radiation when open.
Avoid exposure to beam.
Copyright notice
• Where the MAINS plug or an appliance coupler is
used as the disconnect device, the disconnect device
shall remain readily operable.
This product complies with the radio
interference requirements of the European
Community. This product complies with the
requirements of the following directives and
guidelines: 2006/95/EC, 2004/108/EC.
6
EN
This product incorporates copyright protection
technology that is protected by method claims
of certain U.S. patents and other intellectual
property rights owned by Macrovision
Corporation and other rights owners. Use of
this copyright protection technology must be
authorised by Macrovision Corporation, and is
intended for home and other limited viewing
uses only unless otherwise authorised by
Macrovision Corporation. Reverse engineering
or disassembly is prohibited.
This DVD Home Theatre is designed to
complement your home perfectly. Enjoy the
DVD Home Theatre with 9.1 multi-channel
surround sound and excellent picture quality.
Features highlight
Video upscaling to 1080p
You can now watch the DVDs in the highest
picture quality available for your HDTV. This
DVD Home Theatre offers full high-definition
video playback up to 1080p resolution for an
amazing viewing experience. A highly detailed
picture and increased sharpness delivers a more
true-to-life picture.
EasyLink
EasyLink uses the HDMI CEC (Consumer
Electronics Control) industry standard protocol
to share functionality with all HDMI CEC
compliant devices over HDMI. It enables the
connected devices to control each other with a
single remote control.
Note
• Philips does not guarantee 100% interoperability
English
Congratulations on your purchase, and
welcome to Philips! To fully benefit from the
support that Philips offers, register your product
at www.philips.com/welcome.
Ambisound
Philips Ambisound technology reproduces
multi-channel surround sound with fewer
speakers to give an embracing surround
experience without the hassle of setting up a
full range of speaker systems.
USB direct and MP3 link
Simply plug your USB device into the USB
socket to play your MP3/WMA/JPEG/DivX files;
or plug your portable media player to the MP3
LINK socket to enjoy the music play in superb
sound quality.
Sync the audio output with the video play
This DVD Home Theatre provides you the
feature of delaying the audio output if the video
signals that go directly to the TV is slower than
the audio streams.
Region codes
DVD movies are usually not released at the
same time in all regions of the world, thus all
DVD players are programmed to a specific
region code.
Countries
DVD region code
Europe
ALL
2
ALL
5
Russia
with all HDMI CEC devices.
EN
7
Your product
2 Your product
a2
Product overview
• Turn on this unit or turn off to standby
mode.
• Press and hold to turn off this unit and
all the HDMI CEC compliant TV/
devices (for EasyLink control only).
Remote control
b Z (Eject)
• Eject or pull in the disc.
c Source buttons
CINEMA
LIGHTS
• DISC: switch to DISC mode. While in
disc mode, access or exit disc menu.
• USB: switch to USB mode.
• RADIO: switch to FM band.
• AUX/DI /MP3 LINK: switch to AUX
SCART, AUX 1-2-3 INPUT, OPTICAL
1-2 INPUT, DIGITAL INPUT or MP3
LINK that corresponds to the socket
you used to connect the external
device.
d INFO
• Display the current status or disc
information.
• Display photo files in 12 thumbnails
view.
e OPTIONS
• Access or exit Options menu (this
menu provides various setting options).
f u (Play/Pause)
• Start or pause disc play.
• RADIO: start auto radio installation
(only available for first time setup).
g x (Stop)
• Stop disc play.
• RADIO: erase the current preset radio
station.
8
EN
i AUDIO / SYNC
• Select an audio language/channel.
• Press and hold to access audio sync
setting. Then press VOL +- to set
the audio delay time.
• RADIO: toggle between FM stereo and
mono mode.
j SOUND
• Select a predefined sound effect.
k REPEAT / PROGRAM
• Select various repeat or shuffle modes;
turns off repeat or shuffle mode.
• RADIO: press this button to start
manual radio preset.
• RADIO: press and hold this button to
start automatic radio preset.
l CINEMA LIGHTS
• Turn on/off the lights on the speaker
stands to create the cinema ambiance if
the cinema light is enabled.
• Press and hold to enable or disable
cinema lights feature.
m OK
• Confirm an entry or selection.
n Cursor buttons (v V b B)
• Navigate through the on-screen menu.
• Press left or right for fast backward or
forward search.
• RADIO: press up or down to tune the
radio frequency.
• RADIO: press left or right to start auto
search.
o BACK / TITLE
• Return to the previous display menu.
• For DVD, go to title menu.
• For VCD version 2.0 or SVCD with
PBC turned on: return to the menu
during playback.
English
• Switch to treble or bass mode. Then
press VOL +- to set its level setting.
p í/ ë (Previous/Next)
Your product
h TREBLE / BASS
• Skip to the previous or next title/
chapter/track.
• RADIO: select a preset radio station.
q H (Mute)
• Mute or restore the volume.
r VOL +• Adjust the volume level.
s AMBISOUND
• Select different types of surround sound
output.
t Numeric buttons
• Enter a preset number or item to play.
u SUBTITLE
• Select DVD or DivX subtitle language.
v HDMI / ANGLE
• Select a video resolution setting for
HDMI output.
• Press and hold to select a different
viewing angle of a DVD movie.
w ZOOM
• Zoom in or out the picture on the TV.
EN
9
Main unit
11
10
1
2
3
a2
• Turn on this unit or turn off to standby
mode.
• Press and hold to turn on this unit from
low power standby mode.
b SOURCE
• Select a play media: DISC, USB, RADIO
FM, OPTICAL 1-2 INPUT, DIGITAL
INPUT, AUX SCART, AUX 1-2-3
INPUT or MP3 LINK.
4
5
7
8
9
g Z (Eject)
• Eject or pull in the disc.
h Display panel
Right side panel
i Disc compartment
Left side panel
j MP3 LINK socket
• To connect portable audio player.
c x (Stop)
• Stop disc play.
• RADIO: erase the current preset radio
station.
6
k
(USB) socket
• To connect USB flash drive, USB
memory reader or digital camera.
d Volume control
Tip
• Adjust the volume level.
e u (Play/Pause)
• Start or pause disc play.
• RADIO: start auto radio installation
(only available for first time setup).
f AMBISOUND
• Select different types of surround sound
output.
10
EN
• Control buttons on this DVD Home Theatre unit are
•
operated through touch screen display. The control
displays will be dimly lit after one second of inactivity.
To change the brightness of the touch screen display,
see chapter ‘Adjust settings’ - [ General Setup ] >
[ Display Dim ].
You can place the main unit on top of a table
or mount it on the wall.
REAR LEFT
Basic connections:
• Place the unit
• Connect video cables
• Connect junction box
• Connect rear wireless speakers
• Connect front and centre speakers to
subwoofer
• Connect subwoofer
Optional connections:
• Connect audio cables/other devices
• Connect audio from TV
• Connect audio from cable box/
recorder/game console
• Connect portable media player
• Connect USB device
• Mount the DVD Home Theatre unit
product for identification and supply ratings.
FRONT LEFT
FRONT RIGHT
SUBWOOFER
REAR RIGHT
1
2
3
Note
• Refer to the type plate at the rear or bottom of the
English
This section describes the basic connections
required for this DVD Home Theatre unit
before it can be used.
Place the unit
4
• Before you make or change any connections, ensure
that all the devices are disconnected from the power
outlet.
Place this DVD Home Theatre unit near to
the TV.
Place the speaker system as per the
diagram shown above.
• Find the most suitable placement based
on your room layout and set up to
ensure optimum sound performance.
Place the subwoofer at the corner of the
room or at least one metre away from the
TV.
Place the junction box behind the TV, shelf
or table.
• Use the supplied velcro strip for fixing
purpose.
Note
• Rear speakers are labelled as REAR LEFT / RIGHT.
• Front speakers are labelled as FRONT LEFT /
RIGHT.
• To avoid magnetic interference or unwanted noise,
•
never place the speakers too close to the TV or any
radiation devices.
Install this unit near the AC outlet where the AC
power plug can be easily reached.
EN
11
Connect
3 Connect
Connect video cables
This section describes how to connect this
DVD Home Theatre unit to your TV so to
enable viewing of disc play.
Select the best video connection that your TV
can support.
•
HDMI
OUT
Option 1: Connect to HDMI socket (for a
HDMI, DVI or HDCP-compliant TV).
Option 2: Connect to scart socket (for a
standard TV).
•
HDMI IN
Note
• You must connect this unit directly to a TV.
Note
• The HDMI connector is only compatible with HDMI
compliant TVs and DVI-TVs.
Option 1: Connect to HDMI socket
1
Before you connect, remove the rear
cover of the main unit by pushing it
upwards and outwards.
Tip
• To optimise the video output, see chapter ‘Adjust
•
•
•
•
2
12
Connect a HDMI cable (supplied) from the
HDMI OUT on this unit to the HDMI IN
socket on your TV.
EN
settings’ > [ Video Setup ] > [ Advanced Picture ]
for details.
This unit is HDMI CEC compatible. It enables
connected TV/device to control each other over
HDMI, see chapter ‘Activate EasyLink control’ for
details.
Use a HDMI/DVI adaptor in case your TV has only
a DVI connection. An extra audio connection is
needed to complete this connection.
To route the audio from your TV to this DVD Home
Theatre unit, connect an audio cable from the audio
input on this unit to the audio output on your TV.
This type of connections provide best picture quality.
Connect junction box
English
Option 2: Connect to Scart socket
SCART
OUT
1
SCART
1
Connect
TO
MAIN
UNIT
2
TO
SUBWOOFER
Connect a scart cable (supplied) from the
SCART OUT socket on the junction box
to the scart input socket on your TV.
Tip
• To listen to the audio output from your TV, press
•
TO JUNCTION
BOX
AUX/DI /MP3 LINK repeatedly until ‘AUX SCART’
is displayed on the display panel.
This type of connections provide good picture
quality.
1
2
Unwind the DC cable from the main unit
and connect it to the TO MAIN UNIT
socket on the junction box.
• Once complete, close the main unit
rear cover.
Connect interconnect cable between TO
SUBWOOFER socket on the junction box
and TO JUNCTION BOX socket on the
subwoofer.
EN
13
Connect rear wireless
speakers
REAR
RIGHT
Connect front and centre
speakers to subwoofer
REAR
LEFT
FRONT
RIGHT
CENTER
FRONT
LEFT
2
RIGHT
1
1
2
CENTER
LEFT
Connect the cable from the right rear
speaker to the left rear speaker socket.
Connect the power cord from the left rear
speaker to the power outlet when all the
required connections are complete.
1
Connect the centre, left front and right
front speakers to the matching sockets on
the subwoofer.
Note
• Ensure that the front portion of the plug is fully
inserted into the socket.
• To disconnect the Ambisound speakers, press down
the catch on the plug before pulling out.
14
EN
1
2
1
2
This section describes how you can route the
sound from other devices to this DVD Home
Theatre unit in order to enjoy sound output or
audio play with multi-channel surround
capabilities.
Connect audio from TV
(also used for EasyLink control)
Connect the FM antenna (supplied) to the
FM75Ω socket on the subwoofer (for
some models, this cable has been
connected). Extend the FM antenna and
fix its ends to the wall.
AUDIO IN
Connect the power cord when all the
required connections are complete and
you are ready to enjoy this DVD Home
Theatre unit.
AUX 1
1
Connect an audio cable (not supplied)
from the AUDIO IN-AUX1 sockets on
the junction box to the AUDIO OUT
sockets on your TV.
Note
• To listen to the audio output from this connection,
press AUX/DI /MP3 LINK repeatedly until ‘AUX1
INPUT’ is displayed on the display panel.
EN
15
English
Connect audio cables/other
devices
Connect
Connect subwoofer
Connect audio from cable box/
recorder/game console
Connect to digital/optical socket
OPTICAL
DIGITAL-IN
You can choose to connect to analogue or
digital socket depending on the device
capabilities.
COAXIAL
DIGITAL IN
Connect to analogue sockets
OPTICAL OUT
COAXIAL
DIGITAL OUT
L
R
AUX 2
AUX 3
1
Connect a coaxial cable (not supplied)
from the COAXIAL DIGITAL IN socket
on the junction box to the COAXIAL/
DIGITAL OUT socket on the device.
Note
• To listen to the audio output from this connection,
press AUX/DI /MP3 LINK repeatedly until ‘DIGITAL
INPUT’ is displayed on the display panel.
or
1
1
Connect an audio cable (not supplied)
from the AUDIO IN-AUX2 or AUX3
sockets on the subwoofer to the AUDIO
OUT sockets on the device.
Note
• To listen to the audio output from this connection,
press AUX/DI /MP3 LINK repeatedly until ‘AUX2
INPUT’ or ‘AUX3 INPUT’ is displayed on the display
panel.
16
EN
Connect an optical cable (not supplied)
from the OPTICAL DIGITAL IN 1 or 2
socket on the junction box to the
OPTICAL OUT socket on the device.
Note
• To listen to the audio output from this connection,
press AUX/DI /MP3 LINK repeatedly until
‘OPTICAL 1 INPUT’ or ‘OPTICAL 2 INPUT’ is
displayed on the display panel.
Mount the DVD Home
Theatre unit
English
Connect portable media player
Caution!
• Risk of personal injury and damage to the unit.
Allow only qualified persons to mount the unit.
1
1
Pull up the catch to remove the main unit
rear cover.
Connect a 3.5mm stereo audio cable
(supplied) from the MP3 LINK socket on
this unit to the phone socket on your
portable media player (such as MP3 player).
Note
• To listen to the audio output from this connection,
press AUX/DI /MP3 LINK repeatedly until ‘MP3
LINK’ is displayed on the display panel.
Connect USB device
2
3
4
1
Connect the USB device to
socket on this unit.
Remove the screws and detach the DVD
Home Theatre stand.
Place two screws on the wall.
• The distance between two screws is
15cm.
Hook the DVD Home Theatre unit firmly
onto the screws, slide through the key
holes to lock into position.
(USB)
Note
• This DVD Home Theatre unit can only play/view
•
MP3, WMA/WMV9, DivX (Ultra) or JPEG files that
are stored on such devices.
To listen to the audio output from this connection,
press USB.
EN
17
Connect
MP3
4 Get started
Control a play source
1
Prepare the remote control
2
Select the source you wish to control by
pressing the DISC, USB, RADIO or
AUX/DI/MP3 LINK button.
Then select the desired function (for
example í, ë).
Navigate through the menu
1
2
Point the remote control directly at the
remote sensor on this unit and select the
desired function.
Use the following buttons on the remote
control to navigate through the on-screen
menus.
Button
1
2
3
Push to open the battery compartment
cover.
Insert two batteries type R03 or AAA.
Match the indications (+-) inside the
battery compartment.
Close the cover.
Note
• If you are not going to use the remote control for a
long time, remove the batteries.
18
EN
vV
Action
Move up or down.
bB
Move left or right.
Confirm a selection.
Enter numbers.
1
2
3
Press 2 to turn on the DVD Home
Theatre unit.
When you turn on this unit for the first time,
follow the instructions on the TV to complete
the Ambisound setup in order to obtain the
best possible surround sound effect.
Press DISC to switch to disc mode
Turn on the TV and switch it to the
correct video-in channel.
• You may go to the lowest channel on
your TV, then press the Channel Down
button on your TVs remote control
until you see the Video In channel.
• You may press ° button repeatedly
on your TVs remote control.
• Usually this channel is between the
lowest and highest channels and may
be called FRONT, A/V IN, VIDEO, etc..
Note
• Before you start, ensure that you have made all the
required connections.
• Complete the Ambisound setup for this unit before
you insert a disc to play.
1
2
Press DISC to switch to disc mode
Turn on the TV and switch it to the
correct video-in channel.
Language menu is displayed.
OSD Language
Please choose your language:
English
Dansk
Deutsch
Español
Français
Italiano
Tip
• See TVs user manual on how to select the correct
input on your TV.
Stop: Exit
3
Change
Select
Select a language for on-screen display,
then press B.
A welcome message is displayed.
EN
English
Start Ambisound setup
Get started
Find the correct viewing
channel
19
6
Welcome
The next few steps will help you set up your
Home Theater System to match your
7
Select the rear speakers placement in the
room, then press B.
The speaker setting is complete, press B to
exit.
listening environment.
To optimize the Ambisound surround effect for your
home, please begin with this simple setup.
Stop: Exit
4
Continue
• To change the menu display language, see chapter
Press B to continue.
[ Room Acoustics ] menu is displayed.
•
Please select the type of walls that surround
your room:
Hard (Concrete, wood)
Soft (Curtains, open space)
Back
Change
Select
Select the condition of the room, then
press B.
[ Rear Speaker Placement ] menu is
displayed.
Rear Speaker Placement
Select the placement of the rear speakers
in your room:
Against both wall (<0.5m)
Against both wall (>0.5m)
Against side wall (>0.5m)
Against back wall (>0.5m)
Back
20
Tip
• To skip the Ambisound setup, press x
to exit.
Room Acoustics
5
This DVD Home Theatre unit is now ready for
use.
EN
Change
Select
‘Adjusting settings’ - [ General setup ] > [ OSD
Language ] for details.
If you connect this unit to a HDMI CEC compliant
TV using a HDMI cable, it switches automatically to
the menu display language as per your TV setting.
Optimise wireless
transmission
English
REAR
LEFT
Note
• Before you start, ensure that the left rear speaker
6
Get started
After connecting the speakers and subwoofer,
you can adjust the wireless settings to optimise
the wireless performance.
Press OK to confirm and exit.
and subwoofer are connected to the power outlets.
• The wireless receiver is built into the left rear
•
1
2
3
speaker and the transmitter is built into the
subwoofer.
For optimum wireless transmission, ensure that there
is no obstructions between the left rear speaker and
subwoofer.
Change the frequency channel
Press DISC.
You can change the frequency channel of this
wireless system if the transmission signal is
interfering with other wireless devices/networks
in your home.
Press OPTIONS.
1
Press V to select
[ Audio Setup ] in
the menu, then press B.
2
Audio Setup
Ambisound Setup
Pair Receiver
HDMI Audio
Switch Channel
Press OPTIONS, then select
Setup ].
Select [ Wireless ] > [ Switch Channel ],
then press OK.
Options
Descriptions
[ Auto ]
It selects the best
channel to operate
automatically.
[ Channel A ]
Frequency corresponding
to Wi-Fi channel 1.
[ Channel B ]
Frequency corresponding
to Wi-Fi channel 6.
[ Channel C ]
Frequency corresponding
to Wi-Fi channel 11.
Speaker Volume
Speaker Delay
Night Mode
Wireless
4
5
Select [ Wireless ] > [ Pair Receiver ],
then press OK.
Press and hold CONNECT on the left
rear speaker to start pairing the receiver to
the transmitter.
The light flashes while in pairing mode.
A confirmation message is displayed
once the pairing process is complete.
• Pairing has to be done within 30
seconds and audio is muted during this
process.
3
4
[ Audio
Press vV to select a setting, then press
OK.
To exit the menu, press OPTIONS.
EN
• If the volume control is not used within 10 seconds it
21
5
Adjust speakers output
Ideally the distance between listening position
and all the speakers should be the same. If not,
change the speaker settings based on their
distance from the listening position in order to
obtain the best possible surround sound.
1
2
3
Press b B to adjust the volume level, then
press OK.
The test tone is emitted from the
speaker which you are adjusting.
• Repeat the above setting for other
speakers until all the speakers output
level sounds equally balance.
To set the output delay time (centre and rear
speakers only)
Press DISC.
Press OPTIONS.
Press V to select
[ Audio Setup ] in the
menu, then press B.
6
Select [ Speakers Delay ] in the menu,
then press B.
Speakers Delay Setup
Audio Setup
Ambisound Setup
HDMI Audio
Speaker Volume
Speaker Delay
7
Night Mode
Wireless
• You cannot access speaker setup
options if this Home Theatre unit is not
in a complete stop mode. In such case,
press x twice.
8
To set the speakers volume level
4
Select [ Speakers Volume ] in the menu,
then press B.
0ms
Rear Right
0ms
Press b B to set the delay time, then press
OK.
• Repeat the above setting for other
speakers until the sound output from
different speakers reach the listening
position at the same time.
To exit the menu, press OPTIONS.
• Set longer delay time if the centre or rear speakers
•
Front Left
0dB
Front Right
0dB
Center
0dB
Subwoofer
0dB
Rear Left
0dB
Rear Right
0dB
EN
0ms
Rear Left
Tip
Speakers Level Setup
22
Center
are closer to the listening position than the front
speakers.
1ms setting for every 30cm distance between the
speaker and the listening position.
Activate EasyLink control
1
2
Turn on the HDMI CEC operations on
your TV and other connected devices. See
TVs/devices manual for details.
You can now enjoy the EasyLink controls.
One touch play [ Auto Wake-up TV ]
When you press PLAY button, this unit will
wake-up from standby mode and start disc
play (if a video disc is found in the disc
compartment) and it will also turn on your
TV and switch to the correct viewing
channel.
One touch power off [ System Standby ]
When you press and hold STANDBY
button, it will turn off this unit and all the
linked devices to standby.
This unit also responses to standby
command from other HDMI CEC devices.
One touch audio input switching [ System
Audio Control ]
This unit is able to render the audio signals
from the active source. It switches
automatically to the corresponding audio
input and output the sound from its
speaker system.
• Before you can enjoy this function, you
have to map the audio inputs to the
connected devices.
• You can use any HDMI CEC TV/device
remote control to adjust the volume.
be placed in the disc compartment before operation.
• Philips does not guarantee 100% interoperability
English
• To enable one touch play function, a video disc must
with all HDMI CEC compliant devices.
Get started
This feature is only applicable if this unit is
connected to HDMI CEC compliant TV/device.
It enables all the linked devices response or
react to certain commands simultaneously with
one touch control.
Note
Map the audio inputs to the
connected devices
Note
• Before you start, ensure that an audio connection
has been made between this unit and your TV/
devices.
1
2
3
4
Press DISC.
Press OPTIONS.
[ General Setup ] menu is displayed.
Press B.
Select [ EasyLink ], then press B.
General Setup
EasyLink
Auto Wake-up TV
Disc Lock
System Standby
Display Dim
System Audio Control
OSD Language
Audio Input Mapping
Screen Saver
Sleep Timer
Standby Mode
DivX(R) VOD Code
• [ Auto Wake-up TV ] and [ System
Standby ] functions are turned on by
default in the factory.
5
6
Select [ System Audio Control ] > [ On ],
then press OK.
Select [ Audio Input Mapping ], then press
OK.
EN
23
7
Select [ OK ] in the menu, then press OK
to start scanning of devices.
Once complete, audio input mapping
menu is displayed.
Select a play source
On the main unit
Audio Input Mapping
AUX1 Input
TV
AUX2 Input
Other (non-HDMI)
AUX3 Input
Digital Input
1
• For example, if your TV audio is
connected to the AUX IN-AUX 1
sockets on this unit, select [ AUX1
Input ] and map with the TV (brand
name) at the right panel.
8
9
On the remote control
Select the audio input of this unit that is
used to connect to other HDMI device
(e.g. AUX1 Input, AUX2 Input), then press
B.
Select the correct connected device, then
press OK.
• Repeat steps 8~9 to map other
connected devices.
10 To exit the menu, press OPTIONS.
24
Press SOURCE repeatedly to select:
DISC > USB > RADIO FM > OPTICAL
1-2 INPUT > DIGITAL INPUT > AUX
SCART > AUX 1-2-3 INPUT >
MP3 LINK > DISC ...
EN
•
•
•
•
Press DISC to switch to DISC mode.
Press USB to switch to USB mode.
Press RADIO to switch to FM band.
Press AUX/DI /MP3 LINK repeatedly to
select other external devices.
Display
Device connected to
AUX SCART
SCART OUT socket.
AUX1 INPUT
AUDIO IN-AUX1 sockets.
AUX2 INPUT
AUDIO IN-AUX2 sockets.
AUX3 INPUT
AUDIO IN-AUX3 sockets.
OPTICAL 1
INPUT
OPTICAL DIGITAL IN-1
socket.
OPTICAL 2
INPUT
OPTICAL DIGITAL IN-2
socket.
DIGITAL
INPUT
COAXIAL DIGITAL IN
socket.
MP3 LINK
MP3 LINK socket.
5 Play
Play from disc
Playable discs
DVD Video
• Region 2 (Europe)
• Region 5 (Russia)
DVD±RW (DVD Rewritable)
•
•
restrictions. Ensure that the DVD video you play is
for the same region zone as your player (indicated
on its rear).
This unit can support playback of the following file
formats: MP3/WMA/JPEG/DivX/WMV 9.
About WMV 9 - this unit only supports Main Profile
(low level) and Simple Profile. Advanced Profile and
DRM-protected video files are not supported.
Play a disc
Caution!
• Never place any objects other than discs into the
disc compartment.
• Ensure ample space is available at the right hand side
for ease of disc handling.
DVD±R (DVD Recordable)
1
DVD+R DL (DVD+R Double
Layer)
CD-RW (CD-Rewritable)
ReWritable
CD-R (CD-Recordable)
2
3
Insert a disc with its label facing out.
• For double-sided disc, load the side to
play faces out.
• To view disc play, turn on the TV to
the correct viewing channel for this
DVD Home Theatre unit.
To stop disc play, press x.
To remove the disc, press Z.
Tip
Recordable
Audio CD (Compact Disc
Digital Audio)
• If the password entry menu is displayed, you have to
enter the 4-digit password before it can be played.
• Screen saver displays automatically if the disc play
Video CD
• Formats 1.0, 1.1, 2.0
•
Super Video CD
•
is stopped for about 15 minutes. To wake up from
screen saver, press DISC.
This unit automatically switches to standby mode if
you do not press any buttons within 30 minutes after
a disc has stopped playing.
The cinema lights on the speaker stands will gradually
turn off when you start movie play. To turn it on,
press CINEMA LIGHTS.
EN
25
Play
• DVDs and DVD players are designed with regional
English
Note
Play video
Change video play
Note
• For video disc, playback always resumes from the
point where it was last stopped. To start playback
from the beginning, press í while the message is
displayed.
Control a title
1
2
Play a title.
Use the remote control to control the title.
Button
Action
Pause/ resume play.
Stop play.
Jump to the next title/chapter.
Return to the beginning of the
current title/chapter or jump to
the previous title/chapter.
m M
Slow motion reverse/ forward
play.
• To change play speed, press
this button repeatedly.
• For VCD, only forward play
is possible.
vV
26
Search backward/ forward.
• To change search speed,
press this button repeatedly.
EN
1
2
Play a title.
Use the remote control to change the
video play.
Button
Action
Change audio language.
• Only applicable to discs
with multiple audio
language or channel.
Change subtitle language.
• Only applicable to discs
with multiple subtitle
language.
Toggle through various repeat/
shuffle play mode; or turn off
repeat mode.
• Repeat options vary
depending on the disc type.
• For VCDs, repeat play is
only possible when the PBC
mode is turned off.
Zoom in/out.
• To pan through the zoomed
image, press the cursor
buttons.
Display current play status.
• You can change the video
play options here without
interrupting disc play.
Press and hold to view DVD
play from different camera
angles.
• Only applicable to DVDs
that contain sequences
recorded from different
camera angles.
Sync audio output with video play
Play
If the video play is slower than the audio output
(sound does not match with the pictures,) you
can delay the audio output to match the video.
English
Access DVD menu
1
2
Press DISC to access disc main menu.
Select a play option, then press OK.
• In some menus, press number buttons
to input your selection.
• To return to the title menu during
playback, press TITLE.
Access VCD menu
The PBC (Playback Control) for VCD is turned
on by default in the factory. When you load in
a VCD, the contents menu is displayed.
1
1
2
Press and hold AUDIO / SYNC until
‘AUDIO SYNC XXX’ is displayed.
• ‘XXX’ denotes the delay time.
Within five seconds, press VOL +- to
set the delay time for audio output.
Note
• If the volume control is not used within 5 seconds, it
resumes normal volume control function.
Press vV to select a play option, then
press OK to start play.
• If PBC is off, it skips the menu and starts
play from the first title.
• During playback, you can press BACK
to return to the menu (if the PBC
mode is on).
Tip
• The default setting for PBC is on. To change the
default setting, see chapter ‘Adjust settings’ [ Preference Setup ] > [ PBC ] for details.
EN
27
Quick skip play to a specific time
Play DivX® video
DivX video is a digital media format that retains
high quality despite a high rate of compression.
This unit is DivX® Certified that allows you to
enjoy DivX video.
1
1
2
3
During playback, press INFO.
The disc status menu is displayed.
2
Select the current elapsed playing time in
the menu, then press OK.
• [ TT Time ] (title time)
• [ CH Time ] (chapter time)
• [ Disc Time ] (disc time)
• [ Track Time ] (track time)
3
4
Insert a disc or USB that contains the DivX
videos.
Press DISC or USB.
A contents menu is displayed.
Select a title to play, then press u.
Use the remote control to control the
title.
Button
Action
Change subtitle language.
Press the number buttons to change the
time where you want to skip to, then press
OK.
Change audio language/track.
Stop play.
• For DivX Ultra video, press
this button again to display
the contents menu.
Display DivX Ultra video
information.
Note
• Only those DivX videos that were rented or
•
•
•
28
EN
purchased using the DivX registration code of this
unit can be played (see chapter ‘Adjust settings’ >
[ General Setup ] > [ DivX(R) VOD Code ] for
details).
If the subtitle does not appear correctly, change the
subtitle language (see chapter ‘Adjust settings’ [ Preference Setup ] > [ DivX Subtitle ] for details).
The subtitle can only be displayed up to an average
of 45 characters.
This unit can play DivX video files that are up to 4GB
in size.
Play music
• For some commercial audio disc, playback may
resume from the point where it was last stopped. To
start playback from first track, press í.
1
2
Control a track
1
2
Play a track.
3
4
Use the remote control to control the
track.
Button
Action
Pause/ resume play.
Insert a disc or USB that contains the MP3/
WMA music.
Press DISC or USB.
A contents menu is displayed.
Select a folder, then press OK.
Select a track to play, then press u.
• To return to the main menu, press v
until ‘Previous’ folder is selected, then
press OK.
Note
• For CDs recorded in multiple sessions, only the first
session is played.
Stop play.
• This unit does not support MP3PRO audio format.
• If any special characters are present in the MP3 track
Jump to the next track.
•
Return to the beginning of the
current track or jump to the
previous track.
Direct input the track number.
•
name (ID3) or album name, it might not be displayed
correctly on the screen because these characters are
not supported.
Some WMA is protected by Digital Rights
Management (DRM), it cannot be played on this unit.
Folders/files exceed the supported file limit of this
unit will not be displayed or played.
Tip
• To display the data disc contents without folders, see
m M
Search backward/ forward.
• To change search speed,
press this button repeatedly.
chapter ‘Adjust settings’ - [ Preference Setup ] >
[ MP3/JPEG Nav ] for details.
Toggle through various repeat/
shuffle play mode; or turn off
repeat mode.
• Repeat options vary
depending on the disc type.
EN
29
Play
MP3/WMA is a type of highly compressed
audio file (files with .mp3 or .wma extensions).
Note
English
Play MP3/WMA music
Play photo
Note
• It may require longer time to display the disc
Play photos as slideshow
This unit can play JPEG photos (files with .jpeg
or .jpg extensions).
1
2
3
Insert a disc or USB that contains the JPEG
photos.
Press DISC or USB.
For a Kodak disc, the slideshow begins
automatically.
For a JPEG disc, the photo menu is
displayed.
Select the folder/album you want to play.
• To preview the photos in the folder/
album, press INFO.
• To go to previous or next screen
display, press í / ë.
• To select a photo, press the cursor
buttons.
• To display the selected photo only,
press OK.
4
30
Press u to start slideshow play.
• To return to the menu, press BACK.
EN
•
•
•
contents on the TV due to the large number of
songs/photos compiled onto one disc.
If the JPEG photo is not recorded with an ‘exif ’
type file, the actual thumbnail picture will not be
shown on the display. It will be replaced with a ‘blue
mountain’ thumbnail picture.
This unit can only display digital camera pictures
according to the JPEG-EXIF format, typically used by
almost all digital cameras. It cannot display Motion
JPEG and pictures in formats other than JPEG, or
sound clips associated with pictures.
Folders/files exceed the supported file limit of this
unit will not be displayed or played.
Control photo play
1
2
Play photo slideshow.
Use the remote control to control the
photo.
Button
Action
b
Skip to the previous photo.
B
Skip to the next photo.
v
Rotate the photo clockwise.
V
Rotate the photo anticlockwise.
Zoom in/ out.
• Play will pause while in
zoom mode.
Stop play.
Play MP3/WMA music files and JPEG photo
files simultaneously to create musical slideshow.
The MP3/WMA and JPEG files must be stored
on the same disc or USB device.
This unit can only play/view MP3, WMA/
WMV9, DivX (Ultra) or JPEG files that are
stored on such devices.
1
2
3
4
English
Play from USB device
Play
Play musical slideshow
Play MP3/WMA music.
Navigate to the photo folder/album and
press u to start slideshow play.
Slideshow begins and continues till the
end of the photo folder or album.
Audio continues to play till the end of
the disc.
• To return to the menu, press BACK.
To stop slideshow play, press x.
To stop music play, press x again.
1
2
3
4
Connect USB flash drive or USB memory
card reader to the
(USB) socket on
this unit.
Press USB.
A contents menu is displayed.
Select a file to play, then press u.
• For more information, see chapters
‘Play music, Play photo, Play video’ for
details.
To stop play, press x or remove the USB
device.
Tip
• If the device does not fi t into the USB socket,
connect it through a USB extension cable.
• If a multiple USB card reader is used, only one of the
connected USB drive contents can be accessed.
• If a USB HDD is used, ensure that an auxiliary
•
power cord connected to the USB HDD for proper
operations.
Digital cameras that use PTP protocol or require
additional programme installation when connected
to a PC are not supported.
EN
31
Play from portable media
player
Simply connect your portable media player (e.g.
MP3 player) to this unit to enjoy superb sound
quality from your music collections.
Play from radio
Check if the FM antenna has been connected
to the subwoofer. If not, connect the supplied
FM antenna to the FM 75Ω socket and fix its
ends to the wall.
MP3
1
2
3
4
Connect a 3.5mm stereo audio cable
(supplied) from the MP3 LINK socket on
this unit to the ‘headphone’ socket on your
portable media player.
Press AUX/DI /MP3 LINK repeatedly until
‘MP3 LINK’ is displayed.
Start play on your portable media player.
• See chapter ‘Adjust Sound’ to enhance
the audio output.
To stop play, press STOP button on your
portable media player.
Note
• Control playback is only possible on your portable
•
media player.
Stop play on the portable media player before you
switch to other play media/source.
Tip
• For better FM stereo reception, connect an external
FM antenna (not supplied).
• Position the antenna as far away as possible from
your TV, VCR or other radiation source to prevent
unwanted interference.
First time tuning
The first time when you access ‘RADIO’ mode,
follow the instructions to install the radio
stations.
1
2
32
EN
Press RADIO.
’AUTO INSTALL ... PRESS PLAY’ is
displayed.
Press u.
All detected radio stations are stored.
Once complete, it tunes to the first
preset radio station.
• To stop auto tuning, press x.
stations.
• If auto installation is not activated or less than 5
•
radio stations are stored, ‘AUTO INSTALL’ will be
displayed again the next time you turn on to radio
mode.
If the FM radio station transmits RDS (Radio Data
System) data, the name of the radio station will be
displayed.
1
2
Press RADIO.
Press and hold PROGRAM until
‘STARTING INSTALL’ is displayed.
All previously stored radio stations will
be replaced.
Note
• If no stereo signal is detected or less than 5 stations
are detected during radio installation, ‘CHECK
ANTENNA’ is displayed.
Listen to radio
1
2
Press RADIO.
Use the remote control to control the
radio.
Button
Action
Select a preset radio station.
m M
Tune the radio frequency
backward/ forward.
Toggle between FM stereo
and FM mono mode.
Press and hold this button to
delete the preset station from
the preset list.
• The preset number for
other radio stations
remain unchanged
Search and store radio stations
individually
1
2
3
4
5
6
Press RADIO.
Press m M.
The radio frequency indication starts to
change until a radio station is detected.
Repeat step 2 until you tune to the radio
station you wish to store.
• To finetune the radio frequency, press
vV.
Press PROGRAM.
• If no action is carried out within 20
seconds after the above step, it exits
the preset mode.
Press í ë (or the number buttons) to
select a preset number to store.
Press PROGRAM to confirm.
EN
33
Play
• This unit can store up to a maximum of 40 radio
English
Reinstall all the radio stations
Note
6 Adjust sound
Select Ambisound
Control the volume
1
Press VOL +- to increase or decrease
the volume level.
• To mute the volume, press H.
• To restore the volume, press H again
or press the volume button.
1
Press AMBISOUND repeatedly to select a
best Ambisound output that most suits the
video or music you play.
DVD/Multi-channel source
Adjust Bass/Treble
AMBISOUND
9.1
(default setting)
1
2
Press BASS / TREBLE.
Press VOL +-repeatedly to set the
level for low (BASS) or high (TREBLE)
tone.
9.1 multi-channel output
with embracing Ambisound.
Ideal for maximised movie
experience.
MULTICHANNEL 5.1
5.1 multi-channel output for
a standard movie
experience.
AMBISOUND
STEREO 9.1
Duplicate Ambisound
stereo to front and rear
speakers. Ideal for a party.
AMBISOUND
STEREO
Enhanced stereo sound
from your two front
speakers.
CD/Stereo source
Note
• If the volume control is not used within 10 seconds, it
resumes normal volume control function.
34
EN
STEREO
(default setting)
Stereo sound from your
two front speakers.
AMBISOUND
STEREO
Enhanced stereo sound
from your two front
speakers.
AMBISOUND
STEREO 9.1
Duplicate Ambisound
stereo to front and rear
speakers. Ideal for a party.
MULTICHANNEL 9.1
Create a multi-channel
movie experience from
stereo/VCD sources..
1
Adjust sound
English
Select a preset sound effect
Press SOUND repeatedly to select a
sound effect that most suits the video or
music you play.
Video /
Music /
Descriptions
ACTION /
ROCK /
Enhanced low and high
range for great sounding
movie effects and
atmosphere. Great for
action movies and rock/pop
music.
DRAMA /
JAZZ
Clear mid and high range.
Recreates the atmosphere
of a live club with the artist
just in front of you. Good
for Jazz music and watching
dramas.
CONCERT /
CLASSIC
Flat and pure sound mode.
Ideal for listening to classical
music and watching live
concert DVDs.
GAMING /
PARTY
Slightly enhanced low range
and strong mid range ideal
for party music and video
gaming.
SPORTS
Moderate mid range and
surround effects for clear
vocals and the atmosphere
of a live sports venue.
NEWS
Enhanced mid range for
clear vocals/speech.
EN
35
7 Adjust settings
This section describes the various setting
options of this unit.
Symbol
Options
[ EasyLink ]
This feature is only applicable if this unit is
connected to HDMI CEC compliant TV/
device. It enables all the linked devices
response or react to certain commands
simultaneously with one touch control.
[ General Setup ]
Options
Descriptions
[ Audio Setup ]
[ Auto Wakeup TV ]
It wake-ups your TV
automatically when you
press PLAY to power up
this unit and start disc
play (if a video disc is
found in the disc
compartment).
• To disable this feature,
select [ Off ].
[ System
Standby ]
Respond to standby
command from other
HDMI CEC compliant
TV/devices.
• To disable this feature,
select [ Decline ].
[ Video Setup ]
[ Preference Setup ]
General setup
1
2
3
Press OPTIONS.
[ General Setup ] menu is displayed.
Press B.
Select an option, then press OK.
General Setup
EasyLink
Disc Lock
Display Dim
OSD Language
Screen Saver
Sleep Timer
Standby Mode
DivX(R) VOD Code
• See the explanations of the above
options in the following pages.
4
36
Select a setting, then press OK.
• To return to the previous menu, press
BACK.
• To exit the menu, press OPTIONS.
EN
[ System Audio It enables this DVD
Control ]
Home Theatre unit to
switch automatically to
the audio input of the
active device.
• To enable this feature,
select [ On ]. Then
proceed to [ Audio
Input Mapping ] to
scan and map all the
connected devices.
Note
• Your TV and other connected devices must be
compliant with HDMI CEC.
• You must turn on the HDMI CEC operations on
•
your TV/devices before you can enjoy the EasyLink
controls. See your TVs/devices manual for details.
Philips does not guarantee 100% interoperability
with all HDMI CEC compliant devices.
[ Disc Lock ]
Set play restriction for a specific discs.
Before you start, place the disc in the disc
compartment (maximum 40 discs can be
locked).
• [ Lock ] – restrict access to the current
disc. The next time you want to play
this disc or unlock it, you need to enter
the password.
• [ Unlock ] – all discs can be played.
Tip
[ Display Dim ]
Change the brightness level of the display
panel to suit the lighting in your room.
• [ 100% ] – normal brightness.
• [ 70% ] – medium brightness.
• [ 40% ] – dimmest display.
English
Map the audio input to
the connected TV/
devices correctly to
enable automatic
switching of input source.
1. Press OK to start
scanning of devices.
2. Select the audio input
to map (e.g. AUX1
Input, AUX2 Input),
then press B.
3. Select the correct
device that connected
to this audio input,
then press OK.
Adjust settings
[ Audio Input
Mapping ]
[ OSD Language ]
Select the default on-screen menu
language.
[ Screen Saver ]
Turn off or on the screen saver mode. It
helps to protect the TV screen from being
damage due to over exposure to a static
image for too long.
• [ On ] – set the screen saver to appear
after 15 minutes of inactivity (for
example, in pause or stop mode).
• [ Off ] – disable screen saver mode.
[ Sleep Timer ]
Switch to standby automatically after the
preset time.
• [ Off ] – disable sleep mode.
• [ 15, 30, 45, 60 mins ] – select the
count down time before it switches to
standby.
[ Standby Mode ]
Set the standby mode.
• [ Normal ] – normal standby power
consumption.
• [ Low Power ] – low standby power
consumption. However, it requires
longer time to power up.
• To set or change your password, go to
[ Preference Setup ] > [ Password ].
EN
37
[ DivX(R) VOD Code ]
Display the DivX® registration code.
Tip
• Enter this unit’s DivX registration code when you
rent or purchase video from www.divx.com/vod.
The DivX videos rented or purchased through the
DivX® VOD (Video On Demand) service can be
played only on the device to which it is registered.
Audio setup
1
2
3
Press OPTIONS.
[ General Setup ] menu is displayed.
Press V to select
press B.
[ Audio Setup ], then
Select an option, then press OK.
Audio Setup
Ambisound Setup
HDMI Audio
Speaker Volume
Speaker Delay
Night Mode
Wireless
4
38
EN
Select a setting, then press OK.
• To return to the previous menu, press
BACK.
• To exit the menu, press OPTIONS.
When the centre or rear speakers are
placed closer to the listening position than
the front speakers, set the delay time for
these speakers so that the sound outputs
from all speakers reach the listening
position at the same time.
Tip
• See chapter ‘Get Started - Start Ambisound setup’
for detailed information.
[ HDMI Audio ]
When you connect this unit and TV with
HDMI cable, select the audio output
setting for this connection.
• [ On ] – the sound is output through
both your TV and this speaker system.
If the audio format on the disc is not
supported, it will be downmixed to
two-channel sound (linear-PCM).
• [ Off ] – disable audio output from
your TV. The sound is only output
through this speaker system.
[ Speakers Volume ]
When all the speakers are not placed in an
equal distance from the listening position,
change the volume level of the speakers so
that for those placed closer to the listening
position will not sound too loud.
1. To start, press OK.
2. Select a speaker in the menu, then
press b B to set the delay time.
3. Press OK to confirm and exit.
Tip
• 1ms setting for every 30cm distance between the
speaker and the listening position.
[ Night Mode ]
Make loud sound level softer and soft
sound level louder so that you can watch
the DVD movies at a low volume, without
disturbing others.
• [ On ] – for quiet viewing at night
(DVDs only).
• [ Off ] – enjoy surround sound with a
full dynamic range.
1. To start, press OK.
2. Select a speaker in the menu, then
press b B to adjust the volume level.
3. Press OK to confirm and exit.
Tip
• The test tone is emitted from the speaker while
adjusting volume level.
EN
39
English
[ Speakers Delay ]
Change the Ambisound setup by selecting
the room environment and rear speakers
placement.
Adjust settings
[ Ambisound Setup ]
[ Wireless ]
Set up the wireless system for the rear
speakers to enable audio output in
multichannel mode.
• [ Pair Receiver ] – pair the receiver (in
the left rear speaker) with the
transmission signal code of the
transmitter (in the subwoofer).
1. To start, press OK.
2. Press CONNECT on the left rear
speaker for 3 seconds.
3. When pairing process is complete,
press OK to confirm and exit.
Video setup
1
2
3
40
Descriptions
[ Auto ]
It selects the best
channel to operate
automatically.
[ Channel A ]
Frequency corresponding
to Wi-Fi channel 1.
[ Channel B ]
Frequency corresponding
to Wi-Fi channel 6.
[ Channel C ]
Frequency corresponding
to Wi-Fi channel 11.
EN
Press V to select
press B.
[ Video Setup ], then
Select an option, then press OK.
Video Setup
TV Type
TV Display
Picture Settings
Advanced Picture
• [ Switch Channel ] – switch to another
frequency channel to minimise
interference with other wireless devices
in the room.
Options
Press OPTIONS.
[ General Setup ] menu is displayed.
• See the explanations of the above
options in the following pages.
4
Select a setting, then press OK.
• To return to the previous menu, press
BACK.
• To exit the menu, press OPTIONS.
This is an advanced setting to optimise the
video output. This option is only applicable
for video connection through HDMI or
Component Video with Progressive Scan
output.
[ TV Display ]
Select the screen format according to how
you want the picture to appear on your
TV.
4:3 Pan Scan (PS)
4:3 Letter Box (LB)
16:9 (Wide Screen)
• [ 4:3 Pan Scan ] – for standard TV, a
full-height screen display with the sides
trimmed.
• [ 4:3 Letter Box ] – for standard TV, a
‘wide-screen’ display with black bars on
the top and bottom.
• [ 16:9 Wide Screen ] – for wide-screen
TV (frame ratio 16:9).
[ Picture Settings ]
Select a predefined set of picture colour
settings or customise your personal setting.
• [ Standard ] – original colour setting.
• [ Bright ] – vibrant colour setting.
• [ Soft ] – warm colour setting.
• [ Personal ] – customise the colour
setting. Set the level of brightness,
contrast, tint and colour saturation in
the menu, then press OK.
• [ Gamma ] – Adjust picture intensity.
Positive values bring out the detail in
dark scenes, while negative values
emphasise contrast.
• [ Chroma Delay ] – Adjust the colour
of an image element (pixel) to produce
a perfect and clear picture.
• [ True Life ] – Increase the contrast
and colour intensity to produce a more
dynamic picture.
Note
• To adjust the above settings, select an option and
press OK. Then press cursor left or right to change
the value/level setting and press OK to confirm.
• [ Wide Screen Format ] – define the
wide screen format for disc play.
Options
Descriptions
[ Superwide ]
Centre position of the
screen is stretched less
than the side. This
setting is only applicable
if the video resolution is
set to 720p or 1080i/p.
[ 4:3 Pillar
Box ]
No stretching of the
picture. Black bars are
displayed on both sides
of the screen.
[ Off ]
Picture will be displayed
according to the format
of the disc.
EN
41
English
[ Advanced Picture ]
Change this setting only if the video does
not appear correctly. By default, this
setting matches the most common setting
for TVs in your country.
• [ PAL ] – for PAL-system TV.
• [ NTSC ] – for NTSC-system TV.
• [ Multi ] – for TV that is compatible
with both PAL and NTSC.
Adjust settings
[ TV Type ]
Preference Setup
Note
• This setting is only available if you have set the [ TV
Display ] setting to [ 16:9 Wide Screen ].
• [ HDMI Video ] – select a video
resolution that is compatible with your
TV display capability.
1
2
3
Press V to select
then press B.
Descriptions
[ Auto ]
It detects and selects the
best supported video
resolution automatically.
Preference Setup
Select a video resolution
that best supported by
your TV. See your TVs
manual for details.
Subtitle
Audio
Disc Menu
Parental
PBC
MP3/JPEG Nav
Note
Password
DivX Subtitle
• If the setting is not compatible with your TV, a
blank screen appears. Wait for 15 seconds for auto
recover or press HDMI repeatedly until the picture
appears.
EN
[ Preference Setup ],
Select an option, then press OK.
Options
[ 480p, 576p,
720p, 1080i,
1080p ]
42
Press OPTIONS.
[ General Setup ] menu is displayed.
• See the explanations of the above
options in the following pages.
4
Select a setting, then press OK.
• To return to the previous menu, press
BACK.
• To exit the menu, press OPTIONS.
For VCDs/SVCDs recorded with PBC
(playback control,) you can access the disc
contents through an interactive menu.
• [ On ] – an index menu is displayed
when you load a disc for play.
• [ Off ] – skip the menu and start play
from the first title.
[ Subtitle ]
Select the default subtitle language for
DVDs.
[ Disc Menu ]
Select the menu language for DVDs.
Note
• If the language you have set is not available on the
disc, the disc uses its own default language.
• For some DVDs, the subtitle/audio language can only
be changed from the disc menu.
• To select the languages that are not listed in the
menu, select [ Others ]. Then check the Language
Code list at the back of this user manual and enter
the respective 4-digit language code.
[ Parental ]
Restrict access to DVDs that are unsuitable
for your children. These types of DVDs
must be recorded with ratings.
1. To start, press OK.
2. Select a rating level in the menu, then
press OK.
3. Press the number buttons to enter
your 4-digit password.
Note
• Rated DVDs above the level you set in [ Parental ]
require a password to be played.
• The ratings are country-dependent. To allow all discs
to play, select ‘8’.
• Some DVDs have ratings printed on them but are
[ MP3/JPEG Nav ]
Turn off or on MP3/WMA folder display
when you play a media that contains MP3/
WMA files.
• [ With Menu ] – display the folders of
MP3/WMA files.
• [ Without Menu ] – display all the files.
[ Password ]
Follow the instructions on the TV to set or
change the password for locked discs and
play restricted DVDs.
Change Password
Old Password
New Password
Confirm PWD
OK
1. Press the number buttons to
enter ‘0000’ or your last set 4-digit
password at [ Old Password ] field.
2. Enter the new password at [ New
Password ] field.
3. Enter the new password again at
[ Confirm PWD ] field.
4. Press OK to exit the menu.
not recorded with ratings. This function has no
effect on such DVDs.
Note
Tip
• To set or change your password, go to
• If you forget your 4-digit password, enter ‘0000’
before you set a new password.
[ Preference Setup ] > [ Password ].
EN
43
English
[ PBC ]
Select the default audio language for
DVDs.
Adjust settings
[ Audio ]
[ DivX Subtitle ]
Select a character set that supports the
DivX subtitle.
[ Standard ]
English, Irish, Danish,
Estonian, Finnish, French,
German, Italian, Portuguese,
Luxembourgish, Norwegian
(Bokmål and Nynorsk),
Spanish, Swedish, Turkish
[ Central
Europe ]
Polish, Czech, Slovak,
Albanian, Hungarian,
Slovene, Croatian, Serbian
(Latin script), Romanian
[ Cyrillic ]
Belarusian, Bulgarian,
Ukrainian, Macedonian,
Russian, Serbian
Note
• Ensure that the subtitle file has the exact same file
•
name as the movie file. If for example the filename of
the movie is ‘Movie.avi’, then you will need to name
the text file ‘Movie.sub’ or ‘Movie.srt’.
Greek and Hebrew languages can be download
from Philips website, see chapter ‘Update software’.
However, it overrides the Cyrillic language from the
list.
[ Version Info ]
Display the software version of this unit.
Tip
• This information is required when you want to find
out if a newest software version is available at the
Philips website that you may download and install on
this unit.
[ Default ]
Reset all the settings of this unit to factory
default, except for [ Disc Lock ],
[ Password ] and [ Parental ] settings
remain unchanged.
44
EN
Update software
Philips provides software updates to ensure that
this unit is compatible with the newest formats.
To check the updates, compare the current
software version of this unit with the latest
software version available at the Philips website.
1
Press OPTIONS.
Preference Setup
Disc Menu
Parental
Connect the software update cable
(supplied) between SOFTWARE UPDATE
socket on the left rear speaker and
subwoofer.
7
Insert the CD-R or USB flash drive to this
unit.
8
Press DISC or USB, then follow the
instruction on the TV to confirm update
operation.
Note
• Do not remove the CD-R or USB when software
updating is in progress.
9
Once software update is complete, this
unit turns off to standby automatically.
Note
• We recommend that you disconnect the power cord
for a few seconds and connect again to reboot the
system.
PBC
MP3/JPEG Nav
Password
DivX Subtitle
Version Info
Default
2
3
4
5
Select [ Preference Setup ] > [ Version
Info ], then press OK.
Write down the version number, then
press OPTIONS to exit the menu.
Go to www.philips.com/support to check
the latest software version available for this
unit.
If the latest software version is higher than
the software version of this unit, download
it and store onto a CD-R or USB flash
drive
Care
Caution!
• Never use solvents such as benzene, thinner,
cleaners available commercially, or anti-static sprays
intended for discs.
Clean discs
Wipe the disc with a micro fibre cleaning cloth
from the centre to the edge in a straight line
movement.
Clean main unit screen
Wipe the screen surface with a micro fibre
cleaning cloth.
EN
English
6
Additional information
8 Additional
information
45
Specifications
Note
• Specification and design are subject to change
without notice.
Accessories supplied
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Quick Start Guide
Remote control and batteries
Scart cable
HDMI cable
3.5mm stereo audio cable
Interconnect cable (connect between junction box
and subwoofer)
Software cable
2 power cables
Subwoofer
1 centre, 2 front and 2 rear speakers
Junction box
Velcro tape (to fix the junction box)
FM wire antenna
Micro fibre cleaning cloth
Amplifier
•
Total output power (Home Theatre): 800W RMS
(10%THD)
•
•
•
Frequency response: 20 Hz - 20 kHz / ±3dB
Signal-to-noise ratio: > 65 dB (CCIR)
Input sensitivity
• AUX SCART & AUX 1: 500 mV
• AUX 2 & 3: 1000 mV
• MP3 LINK: 250 mV
Disc
•
•
•
•
•
•
•
•
•
•
Laser Type: Semiconductor
Disc diameter: 12cm / 8cm
Video decording: MPEG1/ MPEG2 / DivX /
DIvX Ultra / WMV9
Video DAC: 12 bits, 148 MHz
Signal system: PAL / NTSC
Video S/N: 56 dB
Audio DAC: 24 bits / 192 kHz
Frequency response: 4 Hz - 20 kHz (44.1 kHz)
4 Hz - 22 kHz (48 kHz)
4 Hz - 44 kHz (96 kHz)
PCM: IEC 60958
Dolby Digital, DTS: IEC60958, IEC61937
USB
•
•
46
Compatibility: Hi-Speed USB (2.0)
Class support: UMS (USB Mass Storage Class)
EN
Radio
•
•
•
•
•
•
•
•
Tuning range: FM 87.5-108 MHz (50 kHz)
26dB quieting sensitivity: FM 20 dBf
IF rejection ratio: FM 60 dB
Signal-to-noise ratio: FM 60 dB
Harmonic distortion: FM 3%
Frequency response: FM 180 Hz - 10 kHz /±6dB
Stereo separation: FM 26 dB (1 kHz)
Stereo Threshold: FM 23.5 dB
Power (Subwoofer)
•
•
•
•
•
•
•
•
•
Power supply: 220~240 V, 50 Hz
Power consumption: 120 W
Standby power consumption
• Normal: < 4 W
• Low standby: < 0.3 W
System: Bass Reflex System
Impedance: 4 ohm
Speaker drivers: 165 mm (6 1/2”) woofer
Frequency response: 35 Hz - 200 Hz
Dimensions (WxHxD): 336 x 424.5 x 366 (mm)
Weight: 12.7 kg
Main unit
•
•
Dimensions (WxHxD): 304.2 x 309.8 x 130.1 (mm)
Weight: 3.7 kg
Junction Box
•
•
Dimensions (WxHxD): 168 x 37 x 65 (mm)
Weight: 0.2 kg
Speakers
•
•
•
•
•
•
System: full range satellite
Speaker impedance: 4 ohm (centre),
6 ohm (Front/Rear)
Speaker drivers:
• Centre: 1x 2.5” woofer + 1x 1.5” tweeter
• Front/Rear: 2x 2.5” woofer + 1x 1.5” tweeter
Frequency response: 150 Hz - 20 kHz
Dimensions (WxHxD):
• Centre: 435.4 x 103.8 x 95.4 (mm)
• Front/Rear: 275 x 1117.8 x 288 (mm)
Weight:
• Centre: 1.54 kg
• Front/ Rear: 6.32 kg / 7.14 kg
Wireless rear speakers
•
•
•
Power supply: 220~240 V, 50 Hz
Power consumption: 60 W
Standby power consumption: < 0.5W
English
9 Troubleshooting
• Risk of electric shock. Never remove the casing of
this unit.
To keep the warranty valid, never try to repair the system yourself.
If you encounter problems when using this unit, check the following
points before requesting service. If the problem remains unsolved,
register your product and get support at www.philips.com/welcome.
Main unit
The buttons on this unit do
not work.
• Disconnect this unit from the power outlet for a few minutes,
then connect again.
• Ensure that the interconnect cable from the subwoofer is
connected to the DVD Home Theatre unit.
Picture
No picture.
• See TVs manual for correct video input channel selection.
Change the TV channel until you see the DVD screen.
• Press DISC.
• If this happens when you change the TV type setting, you have
to switch to its default mode:
1. Press Z to eject the disc (if any).
2. Press b (for TV type).
3. Press SUBTITLE.
No picture on HDMI
connection.
• Check if the HDMI cable is faulty. Replace a new HDMI cable.
• If this happens when you change the HDMI video resolution,
press HDMI repeatedly until the picture appears.
EN
47
Troubleshooting
Warning!
Sound
No sound.
• Ensure that the audio cables are connected and press the
correct input source (for example, AUX/DI /MP3 LINK, USB) to
select the device you want to play.
No sound on HDMI
connection.
• You may not hear any sound from the HDMI output if the
connected device is non-HDCP compliant or only DVIcompatible.
• Ensure that the [ HDMI Audio ] setting is turned on.
No sound from TV
programmes.
• Connect an audio cable from the AUDIO input on this unit to
the AUDIO output on your TV. Then press AUX/DI /MP3
LINK repeatedly to select the corresponding audio input source.
Interference on rear
wireless speakers or
existing wireless network in
your home.
• Switch to another frequency channel.
1. Press OPTIONS.
2. Select [ Audio Setup ] > [ Wireless ] > [ Switch Channel ]
in the menu, then press OK.
3. Select a channel option, then press OK.
No sound from rear
wireless speakers.
• Check if all the connections to the wireless speakers are
properly connected and connect the power cable.
• Press AMBISOUND to turn on the Ambisound mode.
• See chapter ‘Getting Started - Optimise wireless transmission’
for proper wireless setup.
Play
DivX video files cannot be
played.
• Ensure that the DivX file is encoded according to the ‘Home
Theatre Profile’ with the DivX encoder.
• Ensure that the DivX video file is complete.
DivX subtitle are not
displayed correctly.
• Ensure that the subtitle file name is the same as the movie file
name.
• Select the correct character set. See chapter ‘Adjust Settings Preference Setup - [ DivX Subtitle ]’.
The contents of the USB
flash drive cannot be read.
• The USB flash drive format is not compatible with this unit.
• Drive is formatted with different file system which is not
supported by this unit (e.g. NTFS).
• Maximum size of memory supported is 160GB.
48
EN
DivX
The DivX code is a patent-pending, MPEG-4
based video compression technology,
developed by DivX Networks, Inc., that can
shrink digital video to sizes small enough to be
transported over the internet, while maintaining
high visual quality.
Dolby Digital
A surround sound system developed by Dolby
Laboratories containing up to six channels of
digital audio (front left and right, surround left
and right, centre and subwoofer).
HDMI
High-Definition Multimedia Interface (HDMI) is
a high-speed digital interface that can transmit
uncompressed high definition video and digital
multichannel audio. It delivers high quality
picture and sound quality, completely free from
noise. HDMI is fully backward-compatible with
DVI.
As required by the HDMI standard, connecting
to HDMI or DVI products without HDCP
(High-bandwidth Digital Content Protection)
will result in no Video or Audio output.
MP3
A file format with a sound data compression
system. ‘MP3’ is the abbreviation of Motion
Picture Experts Group 1 (or MPEG-1) Audio
Layer3. By using the MP3 format, one CD-R or
CD-RW can contain about 10 times more data
than a regular CD. Files are recognised by their
file extension ‘.MP3’.
MPEG
Motion Picture Experts Group. A collection of
compression systems for digital audio and
video.
WMA
Windows Media™ Audio. Refers to an audio
compression technology developed by
Microsoft Corporation. WMA data can be
encoded by using Windows Media Player
version 9 or Windows Media Player for
Windows XP. Files are recognised by their file
extension ‘WMA’.
WMV
Windows Media Video. Refers to a video
compression technology developed by
Microsoft Corporation. WMV content can be
encoded by using Windows Media® Encoder 9
series. Files are recognised by their file
extension ‘WMV’.
HDCP
High-bandwidth Digital Content Protection is a
specification that provides a secure transmission
of digital contents between different devices (to
prevent unauthorised copyright).
EN
49
English
Aspect ratio
Aspect ratio refers to the length to height ratio
of TV screens. The ratio of a standard TV is
4:3, while the ratio of a high-definition or wide
TV is 16:9. The letter box allows you to enjoy
a picture with a wider perspective on a standard
4:3 screen.
JPEG
A very common digital still picture format. A
still-picture data compression system proposed
by the Joint Photographic Expert Group, which
features small decrease in image quality in spite
of its high compression ratio. Files are
recognised by their file extension ‘JPG or JPEG’.
Glossary
10 Glossary
50
EN
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising