Philips | HTD3500K/98 | Owner's Manual | Philips 5.1 Home theatre HTD3500K/98 User manual

Philips 5.1 Home theatre HTD3500K/98 User manual
Always there to help you
Register your product and get support at
www.philips.com/support
Question?
Contact
Philips
User manual
HTD3500K
Contents
1 Important
Safety
Care for your product
Care for the environment
Copyright
2 Your home theater
Main unit
Connectors
Remote control
2
2
3
3
3
4
4
4
5
7 Product specifications
21
8 Troubleshooting
23
9 Language code
25
10 Index
26
3 Connect and setup
6
Speakers
6
Connect to TV
7
Connect audio from TV and other devices 9
4 Use your home theater
10
10
10
12
12
13
13
14
15
15
16
5 Change settings
17
17
17
18
18
19
20
Choose sound
Discs
USB storage devices
DivX
Karaoke
Audio, video, and picture options
Radio
MP3 player
Create MP3 files
EasyLink
Picture
Sound
Language
Parental control
Energy saving
Apply factory settings
6 Update software
20
Check software version
20
Update software through USB or CD-R 20
EN
1
1 Important
Read and understand all instructions before you
use your home theater. If damage is caused by
failure to follow instructions, the warranty does
not apply.
Safety
Risk of electric shock or fire!
• Never expose the product and accessories
to rain or water. Never place liquid
containers, such as vases, near the product.
If liquids are spilt on or into the product,
disconnect it from the power outlet
immediately. Contact Philips Consumer
Care to have the product checked before
use.
• Never place the product and accessories
near naked flames or other heat sources,
including direct sunlight.
• Never insert objects into the ventilation
slots or other openings on the product.
• Where the mains plug or an appliance
coupler is used as the disconnect device,
the disconnect device shall remain readily
operable.
• Batteries (battery pack or batteries
installed) shall not be exposed to excessive
heat such as sunshine, fire or the like.
• Disconnect the product from the power
outlet before lightning storms.
• When you disconnect the power cord,
always pull the plug, never the cable.
Risk of short circuit or fire!
• Before you connect the product to the
power outlet, ensure that the power
voltage matches the value printed on the
back or bottom of the product. Never
connect the product to the power outlet if
the voltage is different.
2
EN
Risk of injury or damage to the home theater!
• For wall-mountable products, use only
the supplied wall mount bracket. Secure
the wall mount to a wall that can support
the combined weight of the product and
the wall mount. Koninklijke Philips N.V.
bears no responsibility for improper wall
mounting that results in accident, injury or
damage.
• For speakers with stands, use only the
supplied stands. Secure the stands to the
speakers tightly. Place the assembled stands
on flat, level surfaces that can support the
combined weight of the speaker and stand.
• Never place the product or any objects
on power cords or on other electrical
equipment.
• If the product is transported in
temperatures below 5°C, unpack the
product and wait until its temperature
matches room temperature before
connecting it to the power outlet.
• Visible and invisible laser radiation when
open. Avoid exposure to beam.
• Do not touch the disc optical lens inside
the disc compartment.
• Parts of this product can be made of
glass. Handle with care to avoid injury and
damage.
Risk of overheating!
• Never install this product in a confined
space. Always leave a space of at least four
inches around the product for ventilation.
Ensure curtains or other objects never
cover the ventilation slots on the product.
Risk of contamination!
• Do not mix batteries (old and new or
carbon and alkaine, etc.).
• Danger of explosion if batteries are
incorrectly replaced. Replace only with the
same or equivalent type.
• Remove batteries if they are exhausted or
if the remote control is not to be used for
a long time.
• Batteries contain chemical substances, they
should be disposed of properly.
Risk of swallowing batteries!
• The product/remote control may contain
a coin/button type battery, which can be
swallowed. Keep the battery out of reach
of children at all times! If swallowed, the
battery can cause serious injury or death.
Severe internal burns can occur within two
hours of ingestion.
• If you suspect that a battery has been
swallowed or placed inside any part of the
body, seek immediate medical attention.
• When you change the batteries, always
keep all new and used batteries out of
reach of children. Ensure that the battery
compartment is completely secure after
you replace the battery.
• If the battery compartment cannot be
completely secured, discontinue use of the
product. Keep out of reach of children and
contact the manufacturer.
This is CLASS II apparatus with double
insulation, and no protective earth provided.
Care for your product
•
•
•
•
Do not insert any objects other than discs
into the disc compartment.
Do not insert warped or cracked discs into
the disc compartment.
Remove discs from the disc compartment
if you are not using the product for an
extended period of time.
Use only microfiber cloth to clean the
product.
Care for the environment
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
Never dispose of your product with other
household waste. Please inform yourself about
the local rules on the separate collection of
electrical and electronic products and batteries.
The correct disposal of these products helps
prevent potentially negative consequences on
the environment and human health.
Your product contains batteries, which cannot
be disposed of with normal household waste.
Please inform yourself about the local rules on
separate collection of batteries. The correct
disposal of batteries helps prevent potentially
negative consequences on the environment and
human health.
Please visit www.recycle.philips.com for
additional information on a recycling center in
your area.
Copyright
This item incorporates copy protection
technology that is protected by U.S. patents
and other intellectual property rights of
Rovi Corporation. Reverse engineering and
disassembly are prohibited.
EN
3
2 Your home
theater
Congratulations on your purchase, and
welcome to Philips! To fully benefit from the
support that Philips offers (e.g. notification
of product software upgrade), register your
product at www.philips.com/welcome.
Front connectors
a
(USB)
Audio, video or picture input from a USB
storage device.
Main unit
b MIC
Audio input from a microphone.
This section includes an overview of the main
unit.
c MUSIC iLINK
Audio input from an MP3 player.
Rear connectors
a Disc compartment
b Display panel
c
(Open/Close)
Open or close the disc compartment, or
eject the disc.
d
(Play/Pause)
Start, pause or resume play.
e SOURCE
Select an audio or video source for the
home theater.
f
(Standby-On)
Switch the home theater on or to standby.
Connectors
This section includes an overview of the
connectors available on your home theater.
4
EN
a AC MAINS
Connect to the power supply.
b SPEAKERS
Connect to the supplied speakers and
subwoofer.
c HDMI OUT
Connect to the HDMI input on the TV.
d OPTICAL
Connect to an optical audio output on the
TV or a digital device.
e VIDEO OUT
Connect to the composite video input on
the TV.
f AUDIO IN-AUX
Connect to an analog audio output on the
TV or an analog device.
g ANTENNA FM
Signal input from an antenna, cable or satellite.
b
Remote control
c REPEAT / PROGRAM
• Selects a repeat or shuffle mode.
• In radio mode, programs radio stations.
This section includes an overview of the
remote control.
d
a
b
u
e
c
d
e
f
r
f
g
h
q
SETUP
Accesses or exits the setup menu.
•
•
•
t
s
OPEN/CLOSE
Opens or closes the disc compartment.
(Navigation buttons)
Navigate menus.
In video mode, press left or right to
fast backward or fast forward.
In radio mode, press left or right to
search a radio station; press up or
down to fine tune a radio frequency.
INFO
Displays information about what is playing.
g Playback buttons
Control playback.
h SURR (Surround Sound)
Switches to surround sound or stereo
sound.
j
i AUDIO SYNC
• Selects an audio language or channel.
• Press and hold to synchronize audio
with video. Use with +/-.
o
k
j Numeric buttons
Selects an item to play.
n
l
p
i
m
k SUBTITLE
Selects subtitle language for video.
l VOCAL
Turns off or on the vocal by changing the
audio channel.
a
(Standby-On)
• Switches the home theater on or to
standby.
• When EasyLink is enabled, press
and hold for at least three seconds
to switch all connected HDMI CEC
compliant devices to standby.
m MIC VOL +/Increases or decreases microphone
volume.
n KARAOKE
Accesses or exits the karaoke menu.
o CREATE MP3 / ZOOM
• Accesses the menu to create MP3.
• Zooms into a video scene or picture.
EN
5
p SOUND
Selects a sound mode.
q VOL +/Increases or decreases volume.
r
(Mute)
Mutes or restores volume.
s
BACK
Returns to a previous menu screen.
t OK
Confirms an entry or selection.
u Source buttons
• AUDIO SOURCE: Selects an audio
input source.
• RADIO: Switches to FM radio.
• USB: Switches to USB storage device.
• DISC: Switches to disc source.
EasyLink controls
With Easylink, you can control your home
theater and the TV with the following buttons
on your home theater remote control (see
'EasyLink' on page 16).
•
(Standby-On): Press and hold to switch
your home theater, TV and the connected
devices to standby.
•
(Play/Pause): When a video disc is in
the disc compartment, wake up the TV
from standby, and then play a disc.
6
EN
3 Connect and
setup
This section helps you connect your home
theater to a TV and other devices, and then set
it up.
For information about the basic connections
of your home theater and accessories, see the
quick start guide.
Note
•• For identification and supply ratings, refer to the type
plate at the back or bottom of the product.
•• Before you make or change any connections, make sure
that all devices are disconnected from the power outlet.
Speakers
Position, connect, and set up your speakers for
best surround sound.
Position
Speaker position plays a critical role in setting
up a surround sound effect.
For best results, place your speakers and the
subwoofer as shown below.
Note
•• Surround sound depends on factors such as room
shape and size, type of wall and ceiling, windows and
reflective surfaces, and speaker acoustics. Experiment
with the speaker positions to find the optimum setting
for you.
Follow these general guidelines, and then set up
your speakers.
1
2
3
4
5
Seating position:
This is the center of your listening area.
FRONT CENTER (front center) speaker:
Place the center speaker directly in front of
the seating position, either above or below
your TV. Make sure that it is close to your
ear height when you are seated.
FRONT LEFT (front left) and FRONT
RIGHT (front right) speakers:
Place the left and right speakers in the
front, and equidistant from the center
speaker in an arc, so that all the three
speakers are at same distance from your
seating position. For best effect, point the
speakers towards the seating position and
place the speakers close to the ear level
(when seated).
Connect to TV
Connect your home theater to a TV to
watch videos. You can listen to audio from TV
programs through your home theater speakers.
Use the best quality connection available on
your home theater and TV.
Option 1: Connect to TV through
HDMI (ARC)
Best quality video
Your home theater supports HDMI version
with Audio Return Channel (ARC). If your TV
is HDMI ARC compliant, connect your home
theater to the TV through the HDMI ARC
connection for easy and quick setup.
With HDMI ARC, you do not need an
additional audio cable to play audio from TV
through your home theater.
1
REAR LEFT (rear left) and REAR RIGHT
(rear right) speakers:
Place the rear surround speakers to the
left and right side of your seating position,
either in line with it or slightly behind it. For
best effect, point the speakers towards the
seating position and place the speakers just
above the ear level (when seated).
SUBWOOFER (subwoofer):
Place the subwoofer at least one meter to
the left or right of the TV. Leave about ten
centimeter clearance from the wall.
Connect
Connect your speakers and the subwoofer to
your home theater as described in the quick
start guide.
Using a High Speed HDMI cable, connect
the HDMI OUT (ARC) connector on
your home theater to the HDMI ARC
connector on the TV.
The HDMI ARC connector on the TV
might be labeled HDMI IN or HDMI. For
details on TV connectors, see the TV user
manual.
TV
2
On your TV, turn on HDMI-CEC. For
details, see the TV user manual.
»» When you play a disc on your home
theater, the video is automatically
displayed on TV and the audio is
automatically played on the home
theater.
EN
7
3
If audio from the TV does not play
automatically on your home theater, set up
the audio manually (see 'Set up audio for
connected devices' on page 9).
Option 2: Connect to TV through
HDMI
Best quality video
If your TV is not HDMI ARC compliant, connect
your home theater to the TV through a
standard HDMI connection.
With a standard HDMI connection, you need
an additional audio cable to play the audio
from the TV through your home theater (see
'Connect audio from TV and other devices' on
page 9).
1
Using a High Speed HDMI cable, connect
the HDMI OUT (ARC) connector on your
home theater to the HDMI connector on
the TV.
The HDMI connector on the TV might be
labeled HDMI IN.
4
Note
•• If your TV has a DVI connector, you can use an HDMI/
DVI adapter to connect to TV.
Option 3: Connect to the TV through
composite video
Basic quality video
If your TV does not have HDMI connectors,
connect your home theater to the TV through a
composite connection. A composite connection
does not support high-definition video.
With a composite connection, you need an
additional audio cable to play the audio from the
TV through your home theater (see 'Connect
audio from TV and other devices' on page 9).
1
TV
2
3
8
On your TV, turn on HDMI-CEC. For
details, see the TV user manual.
»» When you play a disc on your home
theater, the video is automatically
displayed on TV and the audio is
automatically played on the home
theater.
To play audio from TV programs through
your home theater, connect an additional
audio cable (see 'Connect audio from TV
and other devices' on page 9).
EN
If audio from the TV does not play
automatically on your home theater, set up
the audio manually (see 'Set up audio for
connected devices' on page 9).
Using a composite video cable, connect
the VIDEO OUT connector on your
home theater to the composite video
connector on the TV.
The composite video connector might be
labeled AV IN, VIDEO IN, COMPOSITE,
or BASEBAND.
TV
2
3
On your TV, switch to the correct video
input.
To play audio from TV programs through
your home theater, connect an additional
audio cable (see 'Connect audio from TV
and other devices' on page 9).
On your home theater, press SOURCE
repeatedly to select the correct audio input.
Connect audio from TV and
other devices
VCR
Play audio from TV or other devices through
your home theater.
Use the best quality connection available on
your TV, home theater, and other devices.
Note
•• The audio connections in this user manual are only
recommendations. You can use other connections too.
Set up audio for connected devices
When you connect a device to your home
theater, check the audio settings.
1
Option 1: Connect audio through a
digital optical cable
Best quality audio
Using an optical cable, connect the OPTICAL
connector on your home theater to the
OPTICAL OUT connector on the TV or other
device.
The digital optical connector might be labeled
SPDIF, SPDIF OUT, or OPTICAL.
TV
2
3
On your TV and other devices, turn on
HDMI-CEC. For details, see the user
manual of the TV and the other device.
Select 'Amplifier' from the TV speakers
menu. For details, see the TV user manual.
On your home theater, turn on System
Audio Control, and then map the audio
of the connected device to the correct
connectors on your home theater (see
'Play audio from home theater' on page
16).
If the connected device is not HDMI-CEC
compliant, press SOURCE repeatedly on
your home theater to select the correct
audio input.
Option 2: Connect audio through
analog audio cables
Basic quality audio
Using an analog cable, connect the AUX
connectors on your home theater to the
AUDIO OUT connectors on the TV or other
device.
EN
9
4 Use your home
theater
Surround sound mode
Experience an immersive audio experience with
surround sound modes.
1
This section helps you use the home theater to
play media from a wide range of sources.
Before you start
• Make the necessary connections described
in the Quick start guide and the user
manual.
• Switch the TV to the correct source for
the home theater.
Press SURR repeatedly to select a
surround mode.
• [Multi Channel]: Traditional 5.1 channel
for a more relaxing cinematic
experience.
• [Stereo]: Two-channel stereo sound.
Ideal for listening to music.
Note
•• If the audio source is a 2.1 channel, multi-channel mode
will output 5-channel stereo sound.
Choose sound
This section helps you choose the ideal sound
for your video or music.
Sound mode
Select predefined sound modes to suit your
video or music.
1
10
Press SOUND repeatedly to select a
sound mode.
• [Movie Mode]: Enjoy a cinematic audio
experience, specially enhanced for
movies.
• [Music Mode]: Recreate the original
recording environment of your music,
in the studio or at a concert.
• [Original]: Experience the original
sound of your movies and music,
without added sound effects.
• [News]: Hear every word with
optimized speech and clear vocals.
• [Gaming]: Enjoy thrilling arcade sounds,
ideal for action-packed video games or
loud parties.
EN
Discs
Your home theater can play DVDs, VCDs, and
CDs. It can also play discs that you’ve made at
home, such as CD-R discs of photos and music.
What you need
• Audio and video connection between your
home theater and the TV.
• An audio or a video disc.
Play discs
1
2
Insert a disc into the home theater.
»» Your TV switches to the correct source
and the disc plays automatically. If it
does not, press DISC.
Press the play buttons to control play (see
'Play buttons' on page 10).
Play buttons
Button
Action
Navigation
buttons
OK
Navigate menus.
Confirm an entry or selection.
Button
Action
(Play/
Pause)
Start, pause or resume play.
/
/
Navigation
buttons
(left/right)
Navigation
buttons
(up/down)
SUBTITLE
DISC
AUDIO
SYNC
SCREEN
FIT
ZOOM
REPEAT
REPEAT
A-B
ANGLE
INFO
Stop play.
Skip to the previous or next
track, chapter or file.
Fast backwards or fast forwards.
Press repeatedly to change the
search speed.
Rotate the picture clockwise or
counter-clockwise.
Flip the picture vertically or
horizontally.
Select subtitle language for video.
Access or exit the disc menu.
Select an audio language or
channel.
Fit the picture format to the TV
screen.
Zoom into a video scene or
picture.
Select or turn off repeat mode.
Mark two points within a chapter
or track to repeat play, or turn off
the repeat mode.
Select video scenes recorded in
different camera angels.
Access the advanced options
when you play your audio, video,
or media files.
Note
•• To skip the content menu, select [Off].
•• While playing a VCD/SVCD, you can press DISC to
turn off or on the PBC (playback control).
Display menu for MP3/JPEG
You can choose how you want the
MP3 contents to display.
1
2
3
4
Press
SETUP.
Select [Preference Setup], and then press
OK.
Select [MP3/JPEG Display], and then press
OK.
Select the following options, then press
OK.
• [View Folders]: Display the
MP3 folders.
• [View Files]: Display the MP3 files.
Synchronize video and sound
If the audio and video are not synchronized,
delay the audio to match the video.
1
2
3
4
5
Press
SETUP.
Select [Audio Setup], and then press OK.
Select [Audio Sync], and then press OK.
Press the Navigation buttons (left/right) to
synchronize the audio with the video.
Press OK to confirm.
Note
•• Press and hold AUDIO SYNC on the remote control
for quick access to the audio sync setup menu.
Display menu for VCD and SVCD
Display the content menu on VCD and SVCD
discs.
1
2
3
Press
SETUP.
Select [Preference Setup], and then press
OK.
Select [PBC] > [On], and then press OK.
EN
11
USB storage devices
3
Enjoy pictures, audio and video on a USB
storage device.
What you need
• A USB storage device that is formatted for
FAT, and complies with the Mass Storage
Class.
• A USB extension cable, if the USB storage
device does not fit into the connector.
Subtitles
If your video has subtitles in multiple languages,
select a subtitle language.
1
Note
can play the files without using a special computer
program.
Play files
2
3
4
While playing video, press SUBTITLE to
select a language.
Note
•• You can use digital cameras connected by USB if they
1
Select [DivX(R) VOD Code], and then
press OK.
»» The DivX VOD registration code for
your home theater is displayed.
Connect the USB storage device to the
home theater.
Press USB.
»» A content browser is displayed.
Select a file, and then press OK.
Press the playback buttons to control play
(see 'Play buttons' on page 10).
DivX
Play DivX videos from :
• a disc (see 'Discs' on page 10),
• a USB storage device (see 'USB storage
devices' on page 12).
VOD code for DivX
•• Make sure that the subtitle file has the same name as
the video file. For example, if the video file is named
'movie.avi', save the subtitle file as 'movie.srt' or 'movie.
sub'.
•• Your home theater can play subtitle files in the
following formats: .srt, .sub, .txt, .ssa, .ass, smi, and .sami.
These files do not appear in the file navigation menu.
•• If the subtitles do not appear correctly, change the
character set.
Subtitle character set
If the subtitles do not appear correctly, change
the character set that supports the DivX
subtitle.
1
2
3
4
Press
Select [Preference Setup], and then press
OK.
Select [DivX Subtitle], and then press OK.
Select a character set, and the press OK.
Asia Pacific and China
Character Set
Language
[Standard]
Albanian, Danish,
Dutch, English, Finnish,
French, Gaelic,
German, Italian, Kurdish
(Latin), Norwegian,
Portuguese, Spanish,
Swedish, Turkish
Simplified Chinese
Before you purchase DivX videos and play them
on your home theater, register the home theater
on www.divx.com using the DivX VOD code.
1
2
12
Press
SETUP.
Select [General Setup], and then press
OK.
EN
SETUP.
[Chinese]
Character Set
Language
[Chinese-Traditional]
[Korean]
Traditional Chinese
English and Korean
Karaoke
Play a Karaoke disc on your home theater and
sing along with the music.
What you need
• A Karaoke microphone.
• Karaoke discs.
Audio, video, and picture
options
Use advanced features when you play audio,
video, or media files from a disc or a USB
storage device.
Audio options
1
Note
•• To prevent loud feedback or unexpected noise, turn
the microphone volume to the minimum before you
connect the microphone to your home theater.
Play karaoke music
1
2
3
4
5
6
Connect a karaoke microphone to the
MIC connector on your home theater.
Switch your TV to the correct source for
your home theater.
Play a karaoke disc.
Press VOCAL to turn off the vocals and
sing through the microphone.
Press MIC VOL +/- to change the
microphone volume.
Press KARAOKE repeatedly to select a
Karaoke option, then press Navigation
buttons (left/right) and OK to change the
settings.
• [Mic]: Turn the microphone on or off.
• [Echo Level]: Change the echo level.
• [Key]: Change the pitch to match your
voice.
• [Score]: Set the karaoke scoring.
Press INFO repeatedly to cycle through
the following options:
• Show the current track information
and time.
• [Disc Go To:%c%2d:%2d%C]: Skip to a
specific part of the disc by entering the
disc time.
• [Track Go To:%c%2d:%2d%C]: Skip to
a specific part of the track by entering
the track time.
• [Select Track:%c%2d%C/%2d]: Select a
specific track.
Video options
1
2
Press INFO.
»» The video options menu is displayed.
Press the Navigation buttons and OK to
select and change:
• [Title]: Select a specific title.
• [Chapter]: Select a specific chapter.
• [Track]: Select a specific track (for
VCD/SVCD only).
• [Audio]: Select audio language for
video.
• [Subtitle]: Select subtitle language for
video.
• [Angle]: Select video scenes recorded
in different camera angels.
• [TT Time]: Skip to a specific part of
the video by entering the title time.
• [Ch Time]: Skip to a specific part of
the video by entering the chapter time.
• [Disc Time]: Skip to a specific part of
the video by entering the disc time (for
VCD/SVCD only).
EN
13
•
•
•
•
[Track Time]: Skip to a specific part of
the video by entering the track time
(for VCD/SVCD only).
[Preview]: Select a content preview
for disc.
[Repeat]: Select a repeat mode.
[Time Disp.]: Select the information of
time display.
Picture options
1
2
3
Press INFO to access picture preview
mode.
»» 12 thumbnail pictures are displayed.
Radio
Listen to FM radio on your home theater, and
store up to 40 radio stations.
What you need
• FM antenna.
Note
•• AM and digital radio are not supported.
•• If no stereo signal is detected, you are prompted to
install the radio stations again.
•• For the best reception, place the antenna away from
the TV or other sources of radiation.
Press
/ to go to previous or next
preview page.
Press the Navigation buttons and OK to
select a picture.
Slideshows
While playing audio, access fun features such as
picture and musical slideshows.
Tune stations
1
2
Picture slideshows
View a slideshow of your pictures stored in
your disc or a USB storage device.
1
2
Select a picture from a disc or USB storage
device, and then press
.
Press
to stop the slideshow.
Musical slideshows
Create a musical slideshow to play music and
pictures at the same time.
1
2
3
4
5
14
Select a music track, and then press OK.
Press
folder.
BACK, and go to the picture
Select a picture, and then press OK to
start the slideshow.
Press
to stop slideshow.
Press
again to stop music.
EN
3
Connect the FM antenna as described in
the Quick start guide.
Press RADIO.
»» If you have already installed the radio
stations, the last channel that you
listened to is played.
»» If you have not installed any radio
stations, the message AUTO
INSTALL...PRESS PLAY appears on
the display panel. Press (Play).
Press the following buttons to listen or to
change radio stations:
Button
Action
/
Navigation
buttons
(left/right)
Navigation
buttons
(up/down)
Select a preset radio station.
Search for a radio station.
Fine tune a radio frequency.
Press to stop the installation of
radio stations.
Press and hold to erase the
preset radio station.
Button
Action
PROGRAM
Manual:
1) Press PROGRAM.
2) Press Numeric buttons to
select a preset number.
3) Press OK to store the radio
station.
4) Repeat the steps above to
store other radio stations.
Automatic: Press and hold for
three seconds to reinstall the
radio stations
Listen to radio
1
2
Press RADIO.
• To listen to a preset station, press
or .
• To search for a radio station, and then
listen, press Navigation buttons (left/
right).
Press +/- (Volume) to change the volume.
MP3 player
Connect your MP3 player to play your audio
files or music.
What you need
• An MP3 player.
• A 3.5mm stereo audio cable.
Play music
1
2
3
Create MP3 files
Use your home theater to convert audio CDs
into MP3 files.
What you need
• An audio disc.
• A USB storage device
1
2
3
4
5
6
Connect a USB storage device to the
home theater.
Play your audio CD (CDDA/HDCD).
Press CREATE MP3.
»» The create MP3 screen is displayed.
Press the Navigation buttons and OK to
select and change:
• [Speed]: Select the write-to-file speed.
• [Bitrate]: Select the conversion quality.
• [Device]: Select the USB storage
device which you use to store the
MP3 files.
Navigate to the right panel, and then select
the audio tracks and press OK.
• To select all tracks, navigate to [Select
All], and then press OK.
Select [Start], and then press OK to start
the MP3 conversion.
»» A new folder which contains the
MP3 files is created in the USB storage
device.
•
To exit the menu, select [Exit], and
then press OK.
Note
Connect the MP3 player to the home
theater as described in the Quick start
guide.
•• When the conversion is in process, do not press any
Press AUDIO SOURCE repeatedly until
'MUSIC I-LINK' appears on the display
panel.
•• Write-protected or password-protected USB storage
buttons.
•• DTS CDs and copy-protected CDs cannot be
converted.
device cannot be used to store MP3 files.
Press the buttons on the MP3 player to
select and play audio files or music.
EN
15
EasyLink
The home theater supports Philips EasyLink,
which uses the HDMI-CEC (Consumer
Electronics Control) protocol. EasyLinkcompliant devices that are connected through
HDMI can be controlled by a single remote
control.
Philips does not guarantee 100%
interoperability with all HDMI-CEC devices.
What you need
• HDMI-CEC compliant devices.
• An HDMI connection between the
connected devices.
Switch on
1
2
3
4
5
On the TV and other connected devices,
turn on the HDMI-CEC operations. For
details, see the manual of the TV or other
devices.
Press
SETUP.
Select [Video Setup], and then press OK.
Select [HDMI Setup] > [EasyLink Setup]
> [EasyLink], and then press OK.
Select [On], and then press OK.
Control devices
Control the home theater and the other
connected HDMI-CEC compliant devices with
a single remote control.
One-touch play
If you enable One-touch play, the TV
automatically switches to the correct channel
when you play a disc in your home theater.
One-touch standby
When you press and hold (Standby) on the
remote control, the home theater and all the
connected HDMI-CEC devices (that support
one-touch standby) switch to the standby
mode.
If one-touch standby is enabled on your home
theater, you can switch to standby with the
remote control of the TV or other HDMI-CEC
devices.
System Audio Control
When you play a device that has its audio
output routed to the home theater, the home
theater switches to the corresponding audio
source automatically.
To use one-touch audio, turn on System Audio
Control and follow the instructions on the TV
to map connected devices to the audio input
connectors of the home theater.
Audio Input Mapping
When you connect a new device to your home
theater, map the device to the audio input
connector (see 'Play audio from home theater'
on page 16).
Play audio from home theater
Play the audio from a connected device through
your home theater.
1
2
3
4
5
16
EN
Press
SETUP.
Select [Video Setup], and then press OK.
Select [HDMI Setup] > [EasyLink Setup]
> [System Audio Control] > [On], and
then press OK.
• To play the audio from the TV
speakers, select [Off], and skip the
following steps.
Select [HDMI Setup] > [EasyLink Setup]
> [Audio Input Mapping], and then press
OK.
Follow the instructions on the TV to map
the audio of the connected device to the
audio inputs on your home theater.
5 Change settings
This section helps you to change the settings of
your home theater.
Caution
•• Most of the settings are already configured with the
best value for your home theater. Unless you have a
reason to change a setting, it is best to leave it at the
default value.
Picture resolution
To enjoy high definition HDMI video output,
set the HDMI video settings that best match up
with your TV capability.
1
2
3
4
Note
•• You cannot change a setting that is grayed out.
•• To return to the previous menu, press
BACK. To
exit the menu, press
SETUP.
Picture
Change the picture settings to suit your
preferences.
Note
•• The best setting is automatically selected for the TV. If
you change the setting, make sure that the TV supports
the new settings.
Picture settings and format
1
2
3
Press
SETUP.
Select [Video Setup], and then press OK.
Change the following settings, and then
press OK:
• [TV System]: For TV supported video
format.
• [TV Display]: For TV picture display
format.
• [Picture Settings]: Predefined color
settings.
Press
SETUP.
Select [Video Setup], and then press OK.
Select [HDMI Setup], and then press OK.
Change the following settings, and then
press OK:
• [Wide Screen Format]: For 16:9 wide
screen TV display setting.
• [HDMI Video]: HDMI resolution.
High definition picture
Support high definition JPEG pictures.
1
2
3
Press
SETUP.
Select [Video Setup], and then press OK.
Select [HD JPEG] > [On], and then press
OK.
Sound
Change the sound settings to suit your
preference.
HDMI audio
HDMI audio is automatically down-mixed to
two channel for TV speakers. If you do not want
to output audio through your TV, disable the
HDMI audio.
1
2
3
Press
SETUP.
Select [Audio Setup], and then press OK.
Select [HDMI Audio] > [Off], and then
press OK.
EN
17
Night mode
Disc subtitle
For quiet listening, decrease the volume of loud
sounds when you play discs. Night mode is only
available for Dolby-encoded DVD and Blu-ray
discs.
1
2
3
4
1
2
3
Press
SETUP.
Select [Audio Setup], and then press OK.
Select [Night Mode] > [On], and then
press OK.
Language
Select a language for the home menu, audio,
and subtitles.
3
4
Press
SETUP.
Select [General Setup], and then press
OK.
Select [OSD Language], and then press
OK.
Select a menu language for your home
theater, and then press OK.
Disc audio
1
2
3
4
Press
SETUP.
Select [Preference Setup], and then press
OK.
Select [Audio], and then press OK.
Select an audio language for discs, and then
press OK.
Note
•• If your preferred disc language is not available, select
[Others] from the list, and enter the 4-digit language
code found at the end of this user manual (see
'Language code' on page 25).
•• If you select a language that is not available on a disc,
the home theater uses the default language of the disc.
18
EN
SETUP.
Select [Preference Setup], and then press OK.
Select [Subtitle], and then press OK.
Select a subtitle language for discs, and
then press OK.
Disc menu
1
2
3
4
Home menu
1
2
Press
Press
SETUP.
Select [Preference Setup], and then press
OK.
Select [Disc Menu], and then press OK.
Select a menu language for discs, and then
press OK.
Note
•• If your preferred disc language is not available, select
[Others] from the list, and enter the 4-digit language
code found at the end of this user manual (see
'Language code' on page 25).
•• If you select a language that is not available on a disc,
the home theater uses the default language of the disc.
Parental control
Restrict access to discs.
Password
You can set or change your password to play a
restricted disc.
1
2
3
4
5
Press
SETUP.
Select [Preference Setup], and then press
OK.
Select [Password], and then press OK.
»» A change password menu is displayed.
Follow the instructions on the TV to set or
change password.
• If you do not have a password or you
have forgotten, enter 0000.
Press OK.
Ratings
Auto standby
Some discs are recorded with ratings according
to age. You can set up your home theater to
play only discs with an age rating lower than
your child’s age.
When playing a disc or a USB storage device,
automatically switch your home theater to
standby if:
• it is in pause or stop mode, and
• no button is pressed for 30 minutes.
1
2
3
4
5
Press
SETUP.
Select [Preference Setup], and then press
OK.
Select [Parental], and then press OK.
4
SETUP.
Select [General Setup], and then press
OK.
3
Use the Numeric buttons to enter the
password.
Sleep timer
To restrict access to discs that are not encoded
with ratings and parental control, lock the disc
manually. You can lock upto 20 discs on your
home theater.
3
Press
Select an age rating, and then press OK.
• To play all discs irrespective of the
rating, select level 8.
Lock disc
1
2
1
2
While playing a disc, press
SETUP.
Set timers to switch the home theater to
standby after a specified time.
1
2
3
4
Select [General Setup], and then press
OK.
Select [Disc Lock] > [Lock], and then
press OK.
»» A message prompts you to enter the
password.
Enter the password with the Numeric
buttons.
»» The disc is locked.
•
To play the locked disc, enter the
password.
Energy saving
Save energy by changing the following settings.
Select [Auto Standby] > [On], and then
press OK.
5
Press
SETUP.
Select [General Setup], and then press
OK.
Select [Sleep Timer], and then press OK.
Select the duration of the sleep timer.
»» The sleep timer can be set up to
60 minutes. If the sleep timer is set to
[Off], it switches off.
Press OK to activate.
»» The home theater switches to standby
after the specified time.
Screen saver
Automatically switch your home theater to
screen saver mode if:
• it is in pause or stop mode, and
• no button is pressed for 10 minutes.
1
2
3
Press
SETUP.
Select [General Setup], and then press
OK.
Select [Screen Saver] > [On], and then
press OK.
EN
19
Display panel
Change the brightness of the home theater
display panel.
1
2
3
4
Press
SETUP.
Select [General Setup], and then press
OK.
Select [Display Dim], and then press OK.
Reset your home theater to the default settings.
You cannot reset the parental control settings.
3
4
To continue to get the best features and
support for your home theater, update the
software regularly. Compare the version of your
current software with the latest version on
www.philips.com/support.
Select the brightness, and then press OK.
Apply factory settings
1
2
6 Update software
Press
SETUP.
Select [Preference Setup], and then press
OK.
Select [Default], and then press OK.
Select [Reset], and then press OK.
Check software version
1
2
3
Press
SETUP.
Select [Preference Setup], and then press
OK.
Select [Version Info.], and then press OK.
»» The software version is displayed.
Update software through
USB or CD-R
What you need
• A CD-R or a USB flash drive with at least
75MB of memory. The USB flash drive
must be FAT formatted. Do not use a USB
hard drive.
• A computer with Internet access.
• An archive utility that supports the ZIP
file format (for example, WinZip® for
Microsoft® Windows® or Stufflt® for
Macintosh®).
Step 1: Download the latest software
1
2
20
EN
Connect a USB flash drive or insert a
CD-R to your computer.
In your web browser, go to
www.philips.com/support.
3
4
5
6
At the Philips Support website, find your
product and locate the Software and
drivers.
»» The software update is available as a
zip file.
Save the zip file in the root directory of
your USB flash drive or CD-R.
Use the archive utility to extract the
software update file in the root directory.
Remove the USB flash drive or CD-R from
your computer.
Step 2: Update the software
Warning
•• If you use a USB flash drive, make sure that there
is no disc in the disc compartment, and the disc
compartment is closed.
1
2
3
7 Product
specifications
Note
•• Specifications and design are subject to change without
notice.
Region codes
The type plate on the back or bottom of the
home theater shows which regions it supports.
Country
Asia Pacific, Taiwan, Korea
Connect the USB flash drive or insert the
CD-R to your home theater.
Latin America
Switch your TV to the correct source for
your home theater.
Australia, New Zealand
Follow the instructions on the TV to
complete the update.
»» When the software update is
complete, the home theater
automatically switches off . If it does
not, disconnect the power cord for a
few seconds, and then reconnect it.
Note
•• When the software update is in progress, do not turn
DVD
Europe, United Kingdom
Russia, India
China
Media formats
•
off the power, or remove the USB flash drive or CD-R.
DVD-Video, DVD+R/+RW, DVD-R/-RW,
DVD+R/-R DL, CD-R/CD-RW, Audio CD,
Video CD/SVCD, Picture files, MP3 media,
WMA media, DivX media, USB storage
device
File formats
•
•
•
Video: .avi, .divx, .mpg, .mpeg
Audio: .mp3, .wma
Picture: .jpg, .jpeg
EN
21
Amplifier
Main unit
•
•
•
•
•
Total output power:
300W RMS (30% THD)
Frequency response: 20 Hz-20 kHz / ±3 dB
Signal-to-noise ratio: > 65 dB (CCIR) /
(A-weighted)
Input sensitivity:
• AUX: 2 V
• Music iLink: 1 V
•
•
•
Power supply:
• Europe/China/Russia/India:
220-240V~, 50 Hz
• Latin America/Asia Pacific:
110-240V~, 50-60 Hz
Power consumption: 60 W
Standby power consumption: ≤ 0.5 W
Dimensions (W x H x D):
360 x 58 x 325 mm
Weight: 2.3 kg
Video
•
•
•
Subwoofer
Signal system: PAL / NTSC/Multi
HDMI output: 480i/576i, 480p/576p, 720p,
1080i, 1080p
Audio
•
•
•
S/PDIF Digital audio input:
• Optical: TOSLINK
Sampling frequency:
• MP3: 32 kHz, 44.1 kHz, 48 kHz
• WMA: 44.1 kHz, 48 kHz
Constant bit rate:
• MP3: 32 kbps - 320 kbps
• WMA: 64 kbps - 192 kbps
Radio
•
•
•
Tuning range:
• Europe/Russia/China:
FM 87.5-108 MHz (50 kHz)
• Asia Pacific/Latin America:
FM 87.5-108 MHz (50/100 kHz)
Signal-to-noise ratio: FM 50 dB
Frequency response:
FM 200 Hz-12.5 kHz / ±6 dB
USB
•
•
•
•
Compatibility: Hi-Speed USB (2.0)
Class support: USB Mass Storage Class
(MSC)
File system: FAT16, FAT32
Maximum memory support: < 160 GB
22
EN
•
•
•
•
•
•
Output power: 50 W RMS (30% THD)
Impedance: 4 ohm
Speaker drivers: 133 mm (5.25") woofer
Dimensions (W x H x D):
160 x 265 x 265 mm
Weight: 2.50 kg
Cable length: 3 m
Speakers
Center speaker:
• Output power: 50 W RMS (30% THD)
• System: 1 x 63.5 mm (2.5") full range
• Speaker impedance: 4 ohm
• Speaker drivers: 1 x 63.5 mm (2.5") woofer
• Dimensions (W x H x D):
84.5 x 89 x 89 mm
• Weight: 0.27 kg
• Cable length: 2 m
Front/Rear speaker:
• Output power: 4 x 50 W RMS (30% THD)
• Speaker impedance: 4 ohm
• Speaker drivers: 1 x 63.5 mm (2.5") full
range
• Dimensions (W x H x D):
84.5 x89 x 89mm
• Weight (front): 0.27 kg/each
• Weight (rear): 0.27 kg/each
• Cable length (front): 3 m
• Cable length (rear): 7 m
Remote control batteries
•
2 x AAA-R03-1.5 V
Laser
•
•
•
•
Type: Semiconductor laser GaAIAs (CD)
Wave length: 645 - 665 nm (DVD),
770 - 800 nm (CD)
Output power: 6 mW (DVD),
7 mW (VCD/CD)
Beam divergence: 60 degrees.
8 Troubleshooting
Warning
•• Risk of electric shock. Never remove the casing of the
product.
To keep the warranty valid, never try to repair
the product yourself.
If you have problems using this product, check
the following points before you request service.
If you still have a problem, get support at
www.philips.com/support.
Main unit
The buttons on the home theater do not
work.
• Disconnect the home theater from the
power supply for a few minutes, then
reconnect.
Picture
No picture.
• Make sure that the TV is switched to the
correct source for the home theater.
No picture on a TV connected through HDMI.
• Make sure that the HDMI cable is not
faulty. If it is faulty, replace it with a new
cable.
•• If this happens when you change the HDMI
video resolution, switch to its default mode:
Press to open the disc compartment, and
then press 304 on the remote control.
• Wait for 10 seconds for auto recovery,
or change the HDMI video setting (see
'Picture resolution' on page 17).
Disc does not play high-definition video.
• Make sure that the disc contains highdefinition video.
• Make sure that the TV supports highdefinition video.
• Use an HDMI cable to connect to the TV.
EN
23
Sound
No sound from home theater speakers.
• Connect the audio cable from your home
theater to your TV or other devices.
• Reset your home theater to its factory
settings, then switch it off and switch on
again.
• On your home theater, press SOURCE
repeatedly to select the correct audio
input.
Distorted sound or echo.
• If you play audio from the TV through the
home theater, make sure that the TV is
muted.
Audio and video are not synchronized.
• 1) Press and hold AUDIO SYNC.
2) Press +/- within five seconds to
synchronize the audio with the video.
Play
Cannot play a disc.
• Clean the disc.
• Make sure that the home theater supports
the type of disc (see 'Media formats' on
page 21).
• Make sure that the home theater supports
the region code of the disc.
• If the disc is a DVD±RW or DVD±R disc,
make sure that it is finalized.
Cannot play a DivX file.
• Make sure that the DivX file is encoded
according to the 'Home Theater Profile'
with the DivX encoder.
• Make sure that the DivX file is complete.
DivX subtitles do not display correctly.
• Make sure that the subtitle file name is
the same as the movie file name (see
'Subtitles' on page 12).
24
EN
•
Select the correct character set:
1) Press SETUP.
2) Select [Preference Setup] > [DivX
Subtitle].
3) Select the supported character set.
4) Press OK.
Cannot read the contents of a USB storage
device.
• Make sure that the format of the USB
storage device is compatible with the
home theater.
• Make sure that the file system on the USB
storage device is supported by the home
theater.
'input invalid' or 'x' sign appears on the TV.
• The operation is not possible.
EasyLink does not work.
• Make sure that the home theater is
connected to a Philips brand EasyLink
TV, and the EasyLink option is on (see
'EasyLink' on page 16).
When you switch on the TV, the home theater
automatically switches on.
• This behavior is normal when you are using
Philips EasyLink (HDMI-CEC). To make the
home theater work independently, switch
off EasyLink.
9 Language code
Abkhazian
6566
Afar
6565
Afrikaans
6570
Amharic
6577
Arabic
6582
Armenian
7289
Assamese
6583
Avestan
6569
Aymara
6589
Azerhaijani
6590
Bahasa Melayu
7783
Bashkir
6665
Belarusian
6669
Bengali
6678
Bihari
6672
Bislama
6673
Bokmål, Norwegian
7866
Bosanski
6683
Brezhoneg
6682
Bulgarian
6671
Burmese
7789
Castellano, Español
6983
Catalán
6765
Chamorro
6772
Chechen
6769
Chewa; Chichewa; Nyanja 7889
9072
Ё᭛
Chuang; Zhuang
9065
Church Slavic; Slavonic 6785
Chuvash
6786
Corsican
6779
Česky
6783
Dansk
6865
Deutsch
6869
Dzongkha
6890
English
6978
Esperanto
6979
Estonian
6984
Euskara
6985
6976
Faroese
7079
Français
7082
Frysk
7089
Fijian
7074
Gaelic; Scottish Gaelic 7168
Gallegan
7176
Georgian
7565
Gikuyu; Kikuyu
7573
Guarani
7178
Gujarati
7185
Hausa
7265
Herero
7290
Hindi
7273
Hiri Motu
7279
Hrwatski
6779
Ido
7379
Interlingua (International)7365
Interlingue
7365
Inuktitut
7385
Inupiaq
Irish
Íslenska
Italiano
Ivrit
Japanese
Javanese
Kalaallisut
Kannada
Kashmiri
Kazakh
Kernewek
Khmer
Kinyarwanda
Kirghiz
Komi
Korean
Kuanyama; Kwanyama
Kurdish
Lao
Latina
Latvian
Letzeburgesch;
Limburgan; Limburger
Lingala
Lithuanian
Luxembourgish;
Macedonian
Malagasy
Magyar
Malayalam
Maltese
Manx
Maori
Marathi
Marshallese
Moldavian
Mongolian
Nauru
Navaho; Navajo
Ndebele, North
Ndebele, South
Ndonga
Nederlands
Nepali
Norsk
Northern Sami
North Ndebele
Norwegian Nynorsk;
Occitan; Provencal
Old Bulgarian; Old Slavonic
Oriya
Oromo
Ossetian; Ossetic
Pali
Panjabi
Persian
Polski
Português
7375
7165
7383
7384
7269
7465
7486
7576
7578
7583
7575
7587
7577
8287
7589
7586
7579
7574
7585
7679
7665
7686
7666
7673
7678
7684
7666
7775
7771
7285
7776
7784
7186
7773
7782
7772
7779
7778
7865
7886
7868
7882
7871
7876
7869
7879
8369
7868
7878
7967
6785
7982
7977
7983
8073
8065
7065
8076
8084
Pushto
Russian
Quechua
Raeto-Romance
Romanian
Rundi
Samoan
Sango
Sanskrit
Sardinian
Serbian
Shona
Shqip
Sindhi
Sinhalese
Slovensky
Slovenian
Somali
Sotho; Southern
South Ndebele
Sundanese
Suomi
Swahili
Swati
Svenska
Tagalog
Tahitian
Tajik
Tamil
Tatar
Telugu
Thai
Tibetan
Tigrinya
Tonga (Tonga Islands)
Tsonga
Tswana
Türkçe
Turkmen
Twi
Uighur
Ukrainian
Urdu
Uzbek
Vietnamese
Volapuk
Walloon
Welsh
Wolof
Xhosa
Yiddish
Yoruba
Zulu
8083
8285
8185
8277
8279
8278
8377
8371
8365
8367
8382
8378
8381
8368
8373
8373
8376
8379
8384
7882
8385
7073
8387
8383
8386
8476
8489
8471
8465
8484
8469
8472
6679
8473
8479
8483
8478
8482
8475
8487
8571
8575
8582
8590
8673
8679
8765
6789
8779
8872
8973
8979
9085
EN
25
10 Index
A
amplifier
audio
HDMI audio
predefined modes
quality
settings
source
specifications
audio input mapping
audio language
audio options
auto standby
B
brightness
22
17
10
9
17
9
22
16
18
13
19
20
C
care
product
connect
audio (analog cable)
audio (optical cable - digital)
audio from TV and other devices
speakers
TV (Composite)
TV (HDMI)
control
disc play
Easylink (HDMI-CEC)
parental control
radio
create MP3
3
9
9
9
7
8
8
10
6
18
14
15
disable
HDMI-CEC
discs
audio language
EN
16
18
13
10
12
19
18
13
14
10
18
11
13
13
11
11
12
12
12
E
EasyLink (HDMI-CEC)
audio input mapping
control buttons
one-touch play
one-touch standby
play audio
system audio control
enable
auto standby
HDMI-CEC
screen saver
energy
auto standby
brightness
screen saver
sleep timer
F
factory settings
D
26
audio options
control buttons
DivX
lock/unlock
menu language
options
picture
play
subtitle
synchronize picture and sound
time search
titles
display
MP3/JPEG menu
VCD/SVCD menu
DivX
character set
subtitles
VOD code
16
6
16
16
16
16
19
16
19
19
20
19
19
20
H
HDMI
audio
video settings
17
17
HDMI-CEC
K
karaoke
16
13
L
language
audio
disc menu
language code
onscreen menu
subtitle
18
18
25
18
18
M
main unit
specifications
troubleshooting
media formats
MP3
create MP3
display contents
play
O
one-touch play
one-touch standby
options
picture
overview
HDMI-CEC
remote control
settings
22
23
21
15
11
15
16
16
14
16
5
17
P
parental control
lock disc
password
ratings
password
Philips Easylink
picture
high resolution JPEG
19
18
19
18
16
17
options
settings
slideshows
troubleshooting
picture options
play
discs
MP3
radio
slideshows
troubleshooting
USB
position
position
preference
audio
auto standby
change password
disc menu
display panel
menu language
screen saver
sleep timer
subtitle
product specifications
14
17
14
23
14
10
15
22
14
24
12
6
17
19
18
18
20
18
19
19
18
21
R
radio
control buttons
listen to radio
specifications
tune stations
ratings
region codes
remote control
batteries
overview
repeat
14
15
22
14
19
21
23
5
13
S
safety
use of the product
screen saver
settings
audio
2
19
17
EN
27
auto standby
default
disc language
HDMI audio
HDMI video
HDMI-CEC
menu language
parental rating
password
picture
power
restore
screen saver
sleep timer
subtitle language
video
sleep timer
slideshows
musical
picture
software
check current version
update
sound
predefined sound mode
surround sound
synchronize picture and sound
troubleshooting
sound mode
speakers
connect
position
specifications
surround sound
subtitle
character set
language
subwoofer
specifications
synchronize picture and sound
system audio control
T
time search
titles
troubleshooting
28
EN
19
20
18
17
17
16
18
19
18
17
19
20
19
19
18
17
19
14
14
20
20
10
10
11
24
10
7
6
22
10
12
18
22
11
16
13
13
connection
main unit
picture
play
sound
23
23
23
24
24
U
update software
check current version
update
USB
format
USB storage device
options
play
specifications
20
20
22
13
12
22
V
video
picture settings
synchronize picture and sound
VOD code for DivX
video formats
video options
VOD code for DivX
17
11
12
22
13
12
Manufactured under license from Dolby
Laboratories. Dolby and the double-D symbol
are trademarks of Dolby Laboratories.
DivX , DivX Ultra , DivX Certified and
associated logos are trademarks of Rovi
Corporation or its subsidiaries and are used
under license.
DivX Ultra Certified to play DivX video
with advanced features and premium content.
ABOUT DIVX VIDEO: DivX is a digital video
format created by DivX, LLC, a subsidiary
of Rovi Corporation. This is an official DivX
Certified device that plays DivX video. Visit
divx.com for more information and software
tools to convert your files into DivX videos.
ABOUT DIVX VIDEO-ON-DEMAND: This
DivX Certified device must be registered
in order to play purchased DivX Video-onDemand (VOD) movies. To obtain your
registration code, locate the DivX VOD section
in your device setup menu. Go to vod.divx.com
for more information on how to complete your
registration.
HDMI, and HDMI logo, and High-Definition
Multimedia Interface are trademarks or
registered trademarks of HDMI licensing LLC in
the United States and other countries.
CLASS 1
LASER PRODUCT
29
Specifications are subject to change without notice
© 2014 Koninklijke Philips N.V. All rights reserved.
Trademarks are the property of Koninklijke Philips N.V. or their respective owners.
HTD3500K_98_UM_V1.0
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising