Philips | HTS3560/98 | Owner's Manual | Philips 5.1 Home theater HTS3560/98 User manual

Philips 5.1 Home theater HTS3560/98 User manual
Register your product and get support at
www.philips.com/welcome
HTS3560
EN User manual
MS-MY Manual pengguna
ZH-TW 使用手冊
ZH-CN 用户手册
1
2
3
4
5
Notice
6
2
Copyright 2
Open source software 2
Trademarks 2
Important 3
3
4
4
4
Safety
Product care
Health warning
Disposal of your old product and batteries
Your home theater 5
Main unit 5
Remote control 5
Connect your home theater 7
7
7
8
8
Connectors
Connect to the TV
Connect audio from TV or other devices
Connect to the internet
7
Change settings 15
15
15
15
16
16
16
17
Access the setup menu
Change video settings
Change audio settings
Set up network
Set up EasyLink
Change preference settings
Change advanced settings
Update software 17
Check software version 17
Update software from the network 17
Update software from a USB 18
8
Product specifications
9
Troubleshooting 20
18
10 Index 21
Use your home theater 9
9
9
10
11
11
11
12
12
12
13
14
14
14
Before you start
Access the home menu
Choose your sound
Play a disc
Use Bonus View on Blu-ray
Access BD-Live on Blu-ray
Play 3D video
Play from a USB storage device
More play features for disc or USB
Play from radio
Play audio from TV or other devices
Play from an MP3 player
Use Philips EasyLink
EN
1
Eng lis h
Contents
1
Notice
Trademarks
Copyright
“Blu-ray 3D” and “Blu-ray 3D” logo are
trademarks of Blu-ray Disc Association.
This item incorporates copy protection technology
that is protected by U.S. patents and other
intellectual property rights of Rovi Corporation.
Reverse engineering and disassembly are
prohibited.
Open source software
Philips Electronics Singapore Pte Ltd hereby offers
to deliver, upon request, a copy of the complete
corresponding source code for the copyrighted
open source software packages used in this
product for which such offer is requested by the
respective licenses. This offer is valid up to three
years after product purchase to anyone in receipt
of this information. To obtain source code, please
contact open.source@philips.com. If you prefer not
to use email or if you do not receive confirmation
receipt within a week after mailing to this email
address, please write to “Open Source Team,
Philips Intellectual Property & Standards, P.O. Box
220, 5600 AE Eindhoven, The Netherlands”. If you
do not receive timely confirmation of your letter,
please email to the email address above. The texts
of the licenses and acknowledgements for open
source software used in this product are included
on a separate leaflet.
BONUSVIEW™
‘BD LIVE’ and ‘BONUSVIEW’ are trademarks of
Blu-ray Disc Association.
Java and all other Java trademarks and logos are
trademarks or registered trademarks of Sun
Microsystems, Inc. in the United States and/or
other countries.
‘x.v.Colour’ is a trademark of Sony Corporation.
Manufactured under license from Dolby
Laboratories. Dolby, Pro Logic, and the
double-D symbol are trademarks of Dolby
Laboratories.
Manufactured under license under U.S. Patent
#’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762;
6,226,616; 6,487,535; 7,392,195; 7,272,567;
7,333,929; 7,212,872 & other U.S. and worldwide
patents issued & pending. DTS and the Symbol
are registered trademarks, & DTS-HD, and DTSHD Master Audio | Essential and the DTS logos
are trademarks of DTS, Inc. Product includes
software. © DTS, Inc. All Rights Reserved.
2
EN
DivX , DivX Certified and associated logos are
registered trademarks of DivX, Inc. and are used
under license.
DivX Ultra® Certified to play DivX® video with
advanced features and premium content.
ABOUT DIVX VIDEO: DivX® is a digital video
format created by DivX, Inc. This is an official
DivX Certified device that plays DivX video.
Visit www.divx.com for more information and
software tools to convert your files into DivX
video.
ABOUT DIVX VIDEO-ON-DEMAND: This
DivX Certified ® device must be registered in
order to play DivX Video-on-Demand (VOD)
content. To generate the registration code,
locate the DivX VOD section in your device
setup menu. Go to vod.divx.com with this code
to complete the registration process and learn
more about DivX VOD.
®
®
HDMI, and HDMI logo and High-Definition
Multimedia Interface are trademarks or
registered trademarks of HDMI licensing LLC.
LASER RADIATION
DO NOT VIEW DIRECTLY
WITH OPTICAL INSTRUMENTS
CLASS 1M LASER PRODUCT
Important
Eng lis h
2
Read and understand all instructions before you
use your home theater. If damage is caused by
failure to follow instructions, the warranty does
not apply.
Safety
Risk of electric shock or fire!
•• Never expose the product and accessories
to rain or water. Never place liquid
containers, such as vases, near the product.
If liquids are spilt on or into the product,
disconnect it from the power outlet
immediately. Contact Philips Consumer Care
to have the product checked before use.
•• Never place the product and accessories
near naked flames or other heat sources,
including direct sunlight.
•• Never insert objects into the ventilation
slots or other openings on the product.
•• Where the mains plug or an appliance
coupler is used as the disconnect device,
the disconnect device shall remain readily
operable.
•• Disconnect the product from the power
outlet before lightning storms.
•• When you disconnect the power cord,
always pull the plug, never the cable.
Risk of short circuit or fire!
•• Before you connect the product to the
power outlet, ensure that the power
voltage matches the value printed on the
back or bottom of the product. Never
connect the product to the power outlet if
the voltage is different.
Risk of injury or damage to the home theater!
•• For wall-mountable products, use only the
supplied wall mount bracket. Secure the
wall mount to a wall that can support the
combined weight of the product and the
wall mount. Koninklijke Philips Electronics
N.V. bears no responsibility for improper
wall mounting that results in accident, injury
or damage.
•• For speakers with stands, use only the
supplied stands. Secure the stands to the
speakers tightly. Place the assembled stands
on flat, level surfaces that can support the
combined weight of the speaker and stand.
EN
3
••
Never place the product or any objects
on power cords or on other electrical
equipment.
•• If the product is transported in
temperatures below 5°C, unpack the
product and wait until its temperature
matches room temperature before
connecting it to the power outlet.
•• Visible and invisible laser radiation when
open. Avoid exposure to beam.
•• Do not touch the disc optical lens inside the
disc compartment.
Risk of overheating!
•• Never install this product in a confined
space. Always leave a space of at least four
inches around the product for ventilation.
Ensure curtains or other objects never
cover the ventilation slots on the product.
Risk of contamination!
•• Do not mix batteries (old and new or
carbon and alkaline, etc.).
•• Remove batteries if they are exhausted or
if the remote control is not to be used for a
long time.
•• Batteries contain chemical substances, they
should be disposed of properly.
To avoid discomfort such as dizziness, headache
or disorientation, we recommend not watching
3D for extended periods of time. If you
experience any discomfort, stop watching 3D
and do not immediately engage in any potentially
hazardous activity (for example driving a car)
until your symptoms have disappeared. If
symptoms persist, do not resume watching 3D
without consulting a medical professional first.
Parents should monitor their children during 3D
viewing and ensure they do not experience any
discomfort as mentioned above. Watching 3D is
not recommended for children under six years of
age as their visual system is not fully developed yet.
Disposal of your old product
and batteries
Your product is designed and manufactured with
high quality materials and components, which can
be recycled and reused.
Product care
••
••
••
••
Do not insert any objects other than discs
into the disc compartment.
Do not insert warped or cracked discs into
the disc compartment.
Remove discs from the disc compartment
if you are not using the product for an
extended period of time.
Only use microfiber cloth to clean the
product.
Health warning
If you or your family has a history of epilepsy
or photosensitive seizures, consult a medical
professional before exposing yourself to flashing
light sources, rapid image sequences or 3D
viewing.
4
EN
When this crossed-out wheeled bin symbol is
attached to a product it means that the product
is covered by the European Directive 2002/96/
EC. Please inform yourself about the local separate
collection system for electrical and electronic
products.
Please act according to your local rules and do not
dispose of your old products with your normal
household waste.
Correct disposal of your old product helps to
prevent potential negative consequences for the
environment and human health.
Your product contains batteries covered by the
European Directive 2006/66/EC, which cannot be
disposed with normal household waste.
Please inform yourself about the local rules on
separate collection of batteries because correct
disposal helps to prevent negative consequences
for the environmental and human health.
Your home theater
Remote control
Congratulations on your purchase, and welcome
to Philips! To fully benefit from the support that
Philips offers, register your home theater at
www.philips.com/welcome.
Eng lis h
3
1
2
Main unit
6
7
8
9
21
3
20
4
5
6
a Disc compartment
b
(Open/Close)
Opens or closes the disc compartment.
c
(Play/Pause)
Starts, pauses or resumes play.
d
(Stop)
• Stops play.
• In radio mode, erases the current
preset radio station.
e
(Standby-On)
Switches the home theater on or to
standby.
19
10
11
18
17
g
•
•
/
12
13
f SOURCE
Selects an audio/video source for the home
theater.
7
8
9
16
14
15
Skips to the previous or next track,
chapter or file.
In radio mode, selects a preset radio
station.
h Display panel
i Volume control wheel
a
(Standby-On)
Switches the home theater on or to
standby.
• When EasyLink is enabled, press
and hold for at least three seconds
to switch all connected HDMI CEC
compliant devices to standby.
•
EN
5
b
(Home)
Accesses the home menu.
s
c TOP MENU
Accesses the main menu of a video disc.
d
(Options)
Accesses more play options during
playback.
• In radio mode, programs radio stations.
•
e Navigation buttons
• Navigates menus.
• In radio mode, press left or right to
t
(Stop)
Stops play.
Press and hold to eject the disc or
open the disc compartment.
• In radio mode, erases the current
preset radio station.
•
•
(Back)
Returns to a previous menu screen.
u Source buttons
• DISC / POP-UP MENU: Switch to disc
start auto search.
f OK
Confirms an entry or selection.
g
•
/
•
(Previous/Next)
Skips to the previous or next track,
chapter or file.
In radio mode, selects a preset radio
station.
h
(Play)
Starts or resumes play.
i
(Pause)
Pauses play.
j
/
(Fast Backward / Fast Forward)
Fast backwards or fast forwards. Press
repeatedly to change the search speed.
k
(Mute)
Mutes or restores volume.
l AUDIO
In video mode, toggle between audio
languages.
In radio mode, toggle between stereo and
mono.
m Numeric buttons
Selects an item to play.
n SUBTITLE
Selects subtitle language for video.
o Color buttons
Blu-ray discs only: Select a task or option.
p REPEAT
Selects or turns off repeat mode.
q
(Sound options)
Accesses or exits various sound options.
r
+/- (Volume)
Increases or decreases volume.
6
EN
•
•
source. Access the disc menu of a DVD
disc or the pop-up menu of a Blu-ray
disc.
RADIO : Switches to FM radio.
AUDIO SOURCE : Selects an audio
input source.
Connect your home
theater
This section helps you connect your home theater
to a TV and other devices. The basic connections of
the home theater with its accessories are provided
in the Quick Start. For a comprehensive interactive
guide, see www.connectivityguide.philips.com.
Note
•• Refer to the type plate at the back or bottom of
the product for identification and supply ratings.
•• Before you make or change any connections,
ensure that all devices are disconnected from
the power outlet.
Connectors
Back connectors
Side connectors
Eng lis h
4
a
(USB)
Audio, video or picture input from a USB
storage device.
b MP3 LINK
Audio input from an MP3 player.
Connect to the TV
Connect your home theater directly to a TV
through one of the following connectors (from
highest to basic quality video):
a HDMI
b Composite video
Option 1: Connect to the TV through
HDMI
Note
•• If the HDTV has a DVI connector, connect
a AC MAINS~
Connects to the power supply.
b SPEAKERS
Connects to the supplied speakers and
subwoofer.
using an HDMI/DVI adapter.
•• If the TV supports EasyLink HDMI CEC,
control the home theater and TV with one
remote control (see ‘Use Philips EasyLink’ on
page 14).
c LAN
Connects to the LAN input on a broadband
modem or router.
d HDMI OUT
TV
Connects to the HDMI input on the TV.
e VIDEO OUT
Connects to the composite video input on
the TV.
f FM ANTENNA
Connects the FM antenna for radio
reception.
g AUDIO IN
Connects to the analog audio output on the
TV or an analog device.
EN
7
Option 2: Connect to the TV through
composite video (CVBS)
Note
•• The composite video cable or connector might
be labeled AV IN, VIDEO IN, COMPOSITE or
BASEBAND.
TV
Connect audio from TV or
other devices
Use your home theater to play audio from the
TV or other device such as a cable box.
Tip
•• Press AUDIO SOURCE to select the audio
output of your connection.
Option 1: Connect audio through analog
audio cables
Connect to the internet
Connect the home theater to the internet
network and enjoy:
•• BD-Live applications : access to some
exclusive services from the BD-Live enabled
Blu-ray discs (see ‘Access BD-Live on Bluray’ on page 11).
•• Software update : update the software of
the home theater through the network (see
‘Update software from the network’ on
page 17).
What you need:
•• A network router (with DHCP enabled).
•• A network cable (RJ45 straight cable).
•• For BD-Live application and software
update, make sure that the network router
has access to the Internet and the firewall is
disabled.
(Cable not supplied)
LAN
(Cable not supplied)
TV
www
8
EN
1
2
3
4
5
6
7
8
9
Connect the home theater to a broadband
modem or router (see ‘Connect to the
internet’ on page 8).
Turn on your TV and switch to the correct
source for the home theater.
Press (Home).
Select [Setup], then press OK.
Select [Network] > [Network Installation],
then press OK.
Select [Wired (Ethernet)], then press OK.
Select [Auto (recommended)] or [Manual
(advanced)], then press OK.
Follow the instructions on the TV to
complete the setup.
»» The home theater connects to the
internet. If connection fails, select [Retry],
then press OK.
Select [Finish], then press OK to exit.
Caution
•• Familiarize yourself with the network router,
media server software and networking
principles before attempting to connect the
home theater to a computer network. If
necessary, read documentation accompanying
network components. Philips is not responsible
for lost, damaged or corrupt data.
5
Use your home
theater
Eng lis h
Set up network
This section helps you use the home theater to
play media from a wide range of sources.
Before you start
Check that you:
•• Make the necessary connections and
complete the setup as described in the
Quick Start.
•• Switch the TV to the correct source for the
home theater.
Access the home menu
The home menu gives you easy access to
connected devices, audio and video settings, and
other features.
Press (Home).
»» The home menu appears.
1
2
Press the Navigation buttons and OK to
select the following:
• [play Disc] : Starts disc play.
• [browse USB] : Accesses the content
browser of the connected USB storage
device.
• [Setup] : Accesses menus to change
picture, sound and other settings.
EN
9
Choose your sound
This section helps you choose the ideal sound for
your video or music.
•
4
SPORTS : Moderate mid-range and
surround effects for clear vocals and
the atmosphere of a live sport venue.
Press OK to confirm your choice.
Change surround sound mode
1
2
Press
(Sound options).
Press the Navigation buttons (left/right) to
access the sound options.
Sound
experience
Description
SOUND
SURROUND
Selects a sound mode.
Selects a surround sound or
stereo sound.
TREBLE
Adjusts the high frequency
output.
MID
Adjusts the middle frequency
output.
BASS
Adjusts the low frequency
output.
AUDIO SYNC Delays the audio to match the
video.
3
4
Select an option, then press OK.
Press (Back) to exit.
If you do not press a button within five
seconds, it automatically exits the menu.
Change sound mode
Select predefined sound modes to suit your
video or music.
Press
(Sound options).
Select SOUND, then press OK.
Press the Navigation buttons (up/down) to
select the following settings:
• ACTION/ROCK : Enhanced low and
high-range. Ideal for action movies and
rock or pop music.
• DRAMA/JAZZ : Clear mid and highrange. Ideal for drama movies and jazz
music.
• CONCERT/CLASSIC: Neutral sound.
Ideal for live concerts and classical music.
1
2
3
10
EN
Experience an immersive audio experience with
surround sound modes.
Press
(Sound options).
Select SURROUND, then press OK.
Press the Navigation buttons (up/down) to
select the following settings:
• 5CH STEREO : Enhances the stereo
channel output by duplicating the
sound output to the center and rear
speakers. Ideal for party music.
• MULTI-CHANNEL/Dolby PLII :
Immersive multi-channel sound for an
enhanced movie experience.
• STEREO : Two-channel stereo sound.
Ideal for listening to music.
1
2
3
4
Press OK to confirm your choice.
Change treble, mid and bass
Change the high frequency (treble), mid frequency
(mid) and low frequency (bass) settings of the
home theater to suit your video or music.
Press
(Sound options).
Select TREBLE, MID or BASS, then press OK.
Press the Navigation buttons (up/down) to
adjust the frequency level.
Press OK to confirm.
1
2
3
4
Synchronize audio with video
If the audio and video are not synchronized, you
can delay the audio to match the video.
Press
(Sound options).
Select AUDIO SYNC, then press OK.
Press the Navigation buttons (up/down) to
sync the audio with the video.
Press OK to confirm.
1
2
3
4
Note
•• Audio Lip Sync is only available when you play
a video.
3
The home theater can play a wide variety of
discs, including video, audio and mixed media (for
example, a CD-R that contains JPEG pictures and
MP3 music).
Insert a disc into the home theater.
Press DISC, or select [play Disc] in the
home menu and press OK.
»» The disc plays or the disc main menu
appears.
4
1
2
3
Press the following buttons to control play:
Button
Action
Navigation
buttons
OK
(Play)
Navigate menus.
/
/
Navigation
buttons (up/
down)
SUBTITLE
DISC
(Options)
Confirms an entry or selection.
Starts or resumes play.
Pauses play.
Stops play.
Skips to the previous or next
track, chapter or file.
Fast backwards or fast
forwards. Press repeatedly to
change the search speed.
Rotates the picture counterclockwise or clockwise.
Selects subtitle language for
video.
Accesses or exits the disc
menu.
Accesses more play options
during playback.
5
Select [PIP Selection] > [PIP], then press
OK.
»» PIP options [1]/[2] depend on the video
contents.
»» The picture-in-picture video appears in a
small window.
Select [2nd Audio Language] or [2nd
Subtitle Language], then press OK.
Select the language to play, then press OK.
Note
•• To turn off the Bonus View (Picture-inPicture), press (Options), select [PIP
Selection] > [Off], then press OK.
Access BD-Live on Blu-ray
BD-Live enabled Blu-ray discs include exclusive
services such as movies and other online bonuses.
Prepare the internet connection and set up
the network (see ‘Connect to the internet’
on page 8).
Connect the USB storage device to the
home theater.
Select the BD-Live icon in the disc menu,
then press OK.
»» BD-Live starts to load. The loading time
depends on the disc and your internet
connection.
1
2
3
4
5
Press the Navigation buttons to navigate
BD-Live.
Press OK to select an item.
Note
Use Bonus View on Blu-ray
Blu-ray discs that support the Bonus View
feature (also known as Picture-In-Picture) allow
you to view special content such as a director’s
commentary while watching the main feature.
If necessary, enable BonusView (or PictureIn-Picture) in the Blu-ray disc menu.
During playback of the main feature, press
(Options).
»» The options menu is displayed.
1
2
•• The range of BD-Live services depends on
the disc.
•• When you use BD-Live, data on the disc and
home theater are accessed by the content
provider.
•• Use a USB storage device with at least 1GB of
free space to store the downloaded files.
•• If there is insufficient memory to download
BD-Live content, clear memory space.
EN
11
Eng lis h
Play a disc
Play 3D video
Your home theater can play 3D videos on 3D TVs.
Before you start, make sure that:
•• your TV is a 3D TV, and is connected to
your home theater through HDMI,
•• your disc is a Blu-ray 3D disc, and
•• you have 3D glasses that are compatible
with your 3D TV.
To play 3D video
Insert a Blu-ray 3D disc into your home
theater.
»» Your TV switches to the correct HDMI
source, and the disc plays automatically.
1
2
3
4
If the disc does not play automatically, press
DISC or select [play Disc] in the home
menu, and then press OK.
Press the play buttons to control play.
When you search forward or backward,
and in some other play modes, the video
displays in 2D. It returns to 3D when you
play normally again.
Put on the 3D glasses to enjoy the 3D effects.
Play 3D discs in 2D
1
2
3
4
Press (Home).
Select [Setup] > [Video] > [Blu-ray 3D
video] > [Off].
Press OK.
Play your Blu-ray 3D disc.
»» The 3D video is displayed in 2D.
Play from a USB storage device
The home theater is fitted with a USB connector
that allows you to view pictures, listen to music or
watch movies stored on a USB storage device.
Connect the USB storage device to the
home theater.
Press (Home).
»» The home menu appears.
1
2
3
4
5
12
Select [browse USB], then press OK.
»» A content browser appears.
Select a file, then press OK.
Press the playback buttons to control play
(see ‘Play a disc’ on page 11).
EN
Note
•• If the USB storage device does not fit into the
connector, use a USB extension cable.
•• The home theater does not support digital
cameras that need a computer program to
display photos.
•• The USB storage device must be Mass Storage
Class compliant, and formatted to FAT, DOS
or NTFS file system.
More play features for disc or USB
Several advanced features are available for video
or picture playback from a disc or USB storage
device.
Use video options
Access several useful features while viewing video.
Note
•• Available video options depend on the video
source.
1
2
Press (Options).
»» The video options menu appears.
Press the Navigation buttons and OK to
select and adjust:
• [Audio Language] : Selects audio
language for video.
• [Subtitle Language] : Selects subtitle
language for video.
• [Subtitle Shift] : Adjusts the subtitle
position on the screen.
• [Info] : Displays information about
what is playing.
• [Character Set] : Selects a character
set that supports the DivX subtitle.
• [Time Search] : Skips to a specific part
of the video by entering the time of
the scene.
• [2nd Audio Language] : Selects the
second audio language to play.
• [2nd Subtitle Language] : Selects the
second subtitle language to play.
• [Titles] : Selects a specific title.
• [Chapters] : Selects a specific chapter.
• [Angle List] : Selects a different camera
angle.
• [Menus] : Displays the disc menu.
•
•
•
•
[PIP Selection] : Displays Picture-inPicture window.
[Zoom] : Zooms into a video scene or
picture. Press the Navigation buttons
(left/right) to select a zoom factor.
[Repeat] : Repeats a chapter or title.
[Repeat A-B] : Marks two points
within a chapter or track for repeat
play, or turns off repeat mode.
[Picture Settings] : Selects a
predefined color setting.
Use picture options
Access several useful features while viewing pictures.
Press (Options).
»» The pictures options menu appears.
1
2
Press the Navigation buttons and OK to
select and adjust:
• [Rotate +90] : Rotates the picture 90
degree clockwise.
• [Rotate -90] : Rotates the picture 90
degree counter-clockwise.
• [Zoom] : Zooms into a video scene or
picture. Press the Navigation buttons
(left/right) to select a zoom factor.
• [Info] : Displays picture information.
• [Duration per slide] : Sets the display
speed for each picture in a slide show.
• [Slide Animation] : Selects animation
for the slide show.
• [Picture Settings] : Selects a
predefined color setting.
• [Repeat] : Repeats a selected folder.
Use audio options
Access several useful features while audio is played.
Press (Options) repeatedly to cycle
through the following functions:
• REPEAT TRACK : Repeats the current
track.
• REPEAT DISC : Repeats all the tracks
on the disc or folder.
• REPEAT RANDOM : Plays audio
tracks in random order.
• REPEAT OFF : Turns off repeat mode.
1
Play a musical slideshow
Play music and pictures simultaneously to create
a musical slideshow.
Select a music track, then press OK.
Press (Back) and go to the picture folder.
Select a picture, then press OK to start
slideshow.
Press
to stop slideshow.
Press
again to stop music.
1
2
3
4
5
Play from radio
The home theater can store up to 40 radio stations.
Check that the FM antenna is connected.
Press RADIO.
»» “AUTO INSTALL...PRESS PLAY’ appears
on the display panel if you have not
installed any radio stations. Press (Play).
1
2
3
Press the following buttons to control play:
Button
Action
Selects a preset radio station.
/
Navigation Searches for a radio station.
buttons
(left/right)
Navigation Fine tunes a radio frequency.
buttons
(up/down)
Press and hold to erase the preset
radio station.
Press to stop the installation of
radio stations.
Manual: Press once to access
(Options) program mode, and press again to
store the radio station.
Automatic: Press and hold for five
seconds to reinstall radio stations.
AUDIO
Toggles between stereo and mono
sound.
Note
•• AM and digital radio are not supported.
•• If no stereo signal is detected, or if fewer than
five stations are found, you are prompted to
install the radio stations again.
•• For the best reception, place the antenna away
from the TV or other sources of radiation.
EN
13
Eng lis h
•
Change tuning grid
Use Philips EasyLink
In some countries, you can switch the FM tuning
grid between 50 kHz and 100 kHz. Changing the
tuning grid erases all preset radio stations.
Press RADIO.
Press
(Stop).
Press and hold (Play) to toggle between
100 kHz and 50 kHz frequency.
The home theater supports Philips EasyLink,
which uses the HDMI CEC (Consumer
Electronics Control) protocol. EasyLinkcompliant devices that are connected through
HDMI connectors can be controlled by a single
remote control.
1
2
3
Note
Play audio from TV or other
devices
Press AUDIO SOURCE repeatedly to select the
audio output of the connected device.
Play from an MP3 player
Connect and play audio files from an MP3 player
or other external audio devices.
Connect the MP3 player to the home
theater.
Press AUDIO SOURCE repeatedly until
‘MP3 LINK’ appears on the display panel.
Press the buttons on the MP3 player to
select and play audio files.
1
2
3
14
EN
•• Philips does not guarantee 100%
interoperability with all HDMI CEC devices.
1
2
3
4
5
6
Switch on the HDMI CEC operations on
the TV and other connected devices. See
the manual of the TV or other devices for
details.
Press (Home).
Select [Setup], then press OK.
Select [EasyLink] > [EasyLink], then press
OK.
Select [On], then press OK.
You can now enjoy the following Philips
EasyLink controls.
One-touch play
When you play a disc, the TV automatically
switches to the correct channel.
One-touch standby
When you press and hold (Standby) on the
remote control, the home theater and all the
connected HDMI CEC devices (if they support
one-touch standby) switch to standby mode
simultaneously.
System Audio Control
When you play a device that has its audio
output routed to the home theater, the home
theater switches to the corresponding audio
source automatically.
To use one-touch audio, enable this feature and
follow the instructions on the TV to map the
connected devices correctly to the audio input
jacks of the home theater.
Audio Input Mapping
Updates audio input mapping if there are new
devices connected.
Change settings
•
This section helps you to change the settings of
your home theater.
Caution
•• Most of the settings are already configured
with the best value for the home theater.
Unless you have a specific reason to change a
setting, it is best to leave it at the default value.
•
5
[Blu-ray 3D video] : Selects the
3-dimensional video output when you
play a 3D video on your home theater.
The home theater must be connected
to a 3D TV through HDMI.
[Picture Settings] : Selects a
predefined color setting.
Press OK to confirm your choice.
Note
•• The best setting is automatically selected for
Access the setup menu
1
2
3
4
Press (Home).
Select [Setup], then press OK.
»» The setup menu appears.
Select a setup menu, then press OK.
See the following sections for information
about how to change the settings of your
home theater.
Press (Back) to return to the previous
menu, or press to exit.
the TV. If you need to change the setting,
ensure that the TV supports the new setting.
•• For settings related to HDMI, the TV must be
connected through HDMI.
Change audio settings
1
2
3
4
Note
•• You cannot change a setting that is grayed out.
Change video settings
1
2
3
4
Press (Home).
Select [Setup], then press OK.
Select [Video], then press OK.
Select and adjust the following settings:
• [TV Display] : Selects a picture display
format to fit the TV screen.
• [HDMI Video] : Selects the HDMI
video resolution.
• [HDMI Deep Color] : Displays colors
with more shades and hues when
the video content is recorded in
Deep Color and the TV supports this
feature.
5
Press (Home).
Select [Setup], then press OK.
Select [Audio], then press OK.
Select and adjust the following settings:
• [Night Mode] : Selects quiet or full
dynamic sound. Night mode decreases
the volume of loud sounds and
increases the volume of soft sounds
such as speech.
• [HDMI Audio] : Selects HDMI audio
format or disables HDMI audio output
for the TV.
• [Speaker Setup] : Sets the volume level
and distance of each speaker to obtain
the best possible surround sound
based on your room setup.
Press OK to confirm your choice.
Note
•• For settings related to HDMI, the TV must be
connected through HDMI.
•• Night mode is available for Dolby encoded
DVD and Blu-ray discs (for models support
Blu-ray playback).
EN
15
Eng lis h
6
Set up network
1
2
3
4
5
Press (Home).
Select [Setup], then press OK.
Select [Network], then press OK.
Select and adjust the following settings:
• [Network Installation] : Starts
wired (Ethernet) setup. Follow the
instructions to set up the network
connection.
• [View Network Settings] : Displays
the current network settings.
Press OK to confirm your choice.
Note
•• The connected devices must be connected
through HDMI and switched on.
Change preference settings
1
2
3
4
Set up EasyLink
1
2
3
4
5
16
Press (Home).
Select [Setup], then press OK.
Select [EasyLink], then press OK.
Select and adjust the following settings:
• [EasyLink] : Enables or disables
EasyLink.
• [One Touch Play] : Enables or disables
One Touch Play.
If enabled, you can use the remote
control to start disc play in the
home theater and the TV switches
automatically to the correct channel.
• [One Touch Standby] : Enables or
disables One Touch Standby.
If enabled, the home theater can
be switched off to standby by a
remote control from the TV or other
connected HDMI CEC devices.
• [System Audio Control] : Enables or
disables System audio control.
If enabled, follow the instructions on
the TV to map the connected devices
correctly to the audio connectors of
the home theater. The home theater
switches automatically to the audio
source of the connected device.
• [Audio Input Mapping] : Updates audio
input mapping if there are new devices
connected.
Press OK to confirm your choice.
EN
5
Press (Home).
Select [Setup], then press OK.
Select [Preference], then press OK.
Select and adjust the following settings:
• [Menu language] : Selects the onscreen display menu language.
• [Audio] : Selects audio language for video.
• [Subtitle] : Selects subtitle language for
video.
• [Disc Menu] : Selects menu language
for video disc.
• [Parental Control] : Restricts access to
discs that are recorded with ratings. To
play all discs irrespective of the rating,
select level ‘8’.
• [Screen Saver] : Enables or disables
screen saver mode. If enabled, the
screen enters idle mode after 10
minutes of inactivity (for example, in
pause or stop mode).
• [Auto Subtitle Shift] : Enables or
disables shift subtitle. If enabled,
it adjusts the subtitle position
automatically to fit the TV screen.
• [Change Password] : Sets or changes
a PIN code to play a restricted disc.
Enter ‘0000’ if you do not have a PIN
or if you have forgotten your PIN.
• [Display Panel] : Changes the
brightness of the display panel.
• [Auto Standby] : Enables or disables
auto standby. If enabled, the home
theater switches to standby after 30
minutes of inactivity (for example, in
pause or stop mode).
• [VCD PBC] : Displays or skips the
content menu for VCD and SVCD discs.
• [Sleep Timer] : Sets a sleep timer to
switch the home theater to standby
after a specific time.
Press OK to confirm your choice.
•• If your preferred disc language is not available,
you can select [Other] from the list and enter
the 4-digit language code which can be found
at the back of this manual.
•• If you select a language that is not available
on a disc, the home theater uses the default
language of the disc.
Change advanced settings
1
2
3
4
5
Press (Home).
Select [Setup], then press OK.
Select [Advanced], then press OK.
Select and adjust the following settings:
• [BD-Live Security] : Restricts or allows
access to BD-Live.
• [Enhanced Audio] : Enables or disables
the audio post processing at the
speaker output.
• [Software Update] : Selects to update
software from the network or from
USB storage device.
• [Clear memory] : Clears local memory,
delete the BD-Live files that you
previously downloaded. If using an USB
storage device, the local storage folder
is ‘BUDA’.
• [DivX® VOD Code] : Displays the
DivX VOD registration code for the
home theater.
• [Version Info.] : Displays the software
version for the home theater.
• [Restore default settings] : Resets the
home theater to the default settings
programmed at the factory.
Press OK to confirm your choice.
Note
7
Update software
To check for new updates, compare the current
software version of your home theater with the
latest software version (if available) on the Philips
web site.
Check software version
1
2
3
Press (Home).
Select [Setup], then press OK.
Select [Advanced] > [Version Info.], then
press OK.
»» The software version is displayed.
Update software from the
network
1
2
3
4
Prepare the internet connection (see
‘Connect to the internet’ on page 8).
Press (Home) and select [Setup].
Select [Advanced] > [Software Update] >
[Network].
»» If an upgrade media is detected, you are
prompted to start or cancel the update.
Follow the instruction on the TV to confirm
the update.
»» When complete, the home theater
automatically switches off and on again.
• If not, disconnect the power cord for a
few seconds and then reconnect it.
Note
•• If the home theater is unable to connect to the
Philips server, press (Home), select [Setup]
> [Network] > [Network Installation] to set
up the network.
•• You cannot restrict internet access on
commercial Blu-ray discs.
•• Before you purchase DivX videos and play
them on the home theater, register the home
theater on www.divx.com using the DivX
VOD code.
•• You cannot reset parental control setting to its
default value.
EN
17
Eng lis h
Note
Update software from a USB
1
2
3
4
5
6
7
8
Check for the latest software version on
www.philips.com/support.
• Search for your model and click on
‘software and drivers’.
Create a folder named ‘UPG’ in the root
directory of your USB storage device.
Download the software into the ‘\UPG’
folder of the USB storage device.
Unzip the software in the ‘\UPG’ folder.
Connect the USB storage device to the
home theater.
Press (Home) and select [Setup].
Select [Advanced] > [Software Update] >
[USB].
Follow the instructions on the TV to
confirm the update.
»» When complete, the home theater
automatically switches off and restarts.
• If not, disconnect the power cord for a
few seconds and then reconnect it.
Caution
8
Product specifications
Note
•• Specification and design are subject to change
without notice.
Region code
The type plate on the back or bottom of the
home theater shows which regions it supports
Country
Europe,
United Kingdom
Asia Pacific, Taiwan,
Korea
Latin America
BD
A
A
Australia,
New Zealand
Russia, India
C
China
C
•• Do not turn off the power or remove the USB
storage device when the software update is in
progress because you might damage the home
theater.
DVD
Playback media
•• BD-Video, DVD-Video, DVD+R/+RW,
DVD-R/-RW, DVD+R/-R DL, CD-R/CDRW, Audio CD, Video CD/SVCD, Picture
CD, MP3-CD, WMA-CD, DivX (Ultra)-CD,
USB flash drive.
File Format
•• Audio: .mp3, .wma
•• Video: .avi, .divx, .mkv, .wmv
•• Picture: .jpg, .gif, .png
Amplifier
•• Total output power: 1000 W RMS (30%
THD) / 800 W RMS (10% THD)
•• Frequency response: 20 Hz-20 kHz / ±3dB
•• Signal-to-noise ratio: > 65 dB (CCIR) /
(A-weighted)
•• Input sensitivity:
• AUX: 500 mV
• MP3 LINK: 250 mV
18
EN
••
Dimensions (WxHxD):
• Center: 161 x 92 x 95 (mm)
• Speaker : 95 x 161 x 87 (mm)
• Tall speaker (For HTS3580 only): 254 x
1001 x 254 (mm)
•• Weight:
• Center: 0.77 kg
• Speaker: 0.56 kg/each
• Tall speaker (For HTS3580 only): 3.38
kg/each
•• Cable length:
• Center: 3 m
• Front: 4 m
• Rear: 10 m
Laser Specification
•• Laser Type (Diode): InGaN/AIGaN (BD),
InGaAIP (DVD), A IGaAs (CD)
•• Wave length: 405 +5nm/-5nm (BD), 650
+13nm/-10nm (DVD), 790 +15nm/-15nm
(CD)
•• Output power (Max. ratings): 20mW (BD),
7mW (DVD/CD)
EN
19
Eng lis h
Video
•• Signal system: PAL / NTSC
•• HDMI output: 480i/576i, 480p/576p, 720p,
1080i, 1080p
Audio
•• Sampling frequency:
• MP3: 32 kHz, 44.1 kHz, 48 kHz
• WMA: 44.1 kHz, 48 kHz
•• Constant bit rate:
• MP3: 112 kbps - 320 kbps
• WMA: 48 kbps - 192 kbps
Radio
•• Tuning range: FM 87.5-108 MHz (50 kHz)
•• Signal-to-noise ratio: FM 55 dB
•• Frequency response: FM 180 Hz-12.5 kHz
/ ±3dB
USB
•• Compatibility: Hi-Speed USB (2.0)
•• Class support: UMS (USB Mass Storage
Class)
•• File system: FAT16, FAT32, NTFS
•• Maximum memory support: < 160GB
Main Unit
•• Power supply:
• India and Russia: 220-240V; ~50 Hz
• Asia Pacific and Latin America: 110127V/ 220-240V; ~50-60 Hz
•• Power consumption: 100 W
•• Standby power consumption: ≤ 0.9 W
•• Dimensions (WxHxD): 360 x 58 x 351
(mm)
•• Weight: 3.22 kg
Subwoofer
•• Impedance: 4 ohm
•• Speaker drivers: 165 mm (6.5”) woofer
•• Frequency response: 40 Hz-150 Hz
•• Dimensions (WxHxD): 123 x 309 x 369
(mm)
•• Weight: 3.81 kg
•• Cable length: 4 m
Speakers
•• System: full range satellite
•• Speaker impedance: 4 ohm (center), 4 ohm
(Front/Rear)
•• Speaker drivers: 1 x 3” full range
•• Frequency response: 150 Hz-20 kHz
9
Troubleshooting
Warning
•• Risk of electric shock. Never remove the
casing of the product.
To keep the warranty valid, never try to repair the
product yourself.
If you have problems using this product, check the
following points before you request service. If you
still have a problem, register your product and get
support at www.philips.com/welcome.
If you contact Philips, you will be asked for the
model and serial number of your product. The
model number and serial number are on the back
or bottom of your product. Write the numbers
here:
Model No. __________________________
Serial No. ___________________________
Main unit
The buttons on this home theater do not work.
•• Disconnect the home theater from the
power outlet for a few minutes, then
reconnect.
Picture
No picture.
•• Ensure that the TV is switched to the
correct source for the home theater.
No picture on HDMI connection.
•• Change the HDMI video setting or wait for
15 seconds for auto recover.
•• Check if the HDMI cable is faulty. Replace
with a new HDMI cable.
No high-definition video signal on the TV.
•• Ensure that the disc contains high-definition
video.
•• Ensure that the TV supports high-definition
video.
20
EN
Sound
No sound.
•• Ensure that the audio cables are connected
and select the correct input source (for
example, AUDIO SOURCE) for the device
you want to play.
No sound on HDMI connection.
•• You might not hear any sound if the
connected device is not HDCP (Highbandwidth Digital Content Protection)
compliant or only DVI compatible. Use an
analog or digital audio connection.
•• Ensure that the [HDMI Audio] is enabled.
No sound from TV program.
•• Connect an audio cable from the audio
input on the home theater to the audio
output on the TV, then press AUDIO
SOURCE repeatedly to select the correct
audio source.
Distorted sound or echo.
•• Ensure that the TV volume is muted or set
to minimum if you are playing audio through
the home theater.
Audio and video are not synchronized.
•• 1) Press
(Sound options) . 2) Press the
Navigation buttons (left/right) repeatedly
until AUDIO SYNC is displayed, then press
OK. 3) Press the Navigation buttons (up/
down) to sync the audio with the video.
Play
Disc cannot be played.
•• Clean the disc.
•• Ensure that the home theater supports the
disc (see ‘Product specifications’ on page 18).
•• Ensure that the home theater supports the
region code of the disc.
•• For DVD±RW or DVD±R, ensure that the
disc is finalized.
DivX video files cannot be played.
•• Ensure that the DivX file is encoded
according to the ‘Home Theater Profile’
with the DivX encoder.
•• Ensure that the DivX video file is complete.
DivX subtitles do not display correctly.
•• Ensure that the subtitle file name is the
same as the movie file name.
•• Select the correct character set: 1) Press
(Options). 2) Select [Character Set].
3) Select the supported character set.
4) Press OK.
10 Index
3
3D video
12
A
amplifier
audio
connection
language
settings
synchronize with video
audio input mapping
18
8
16
15
10
14, 16
B
BD-Live
access
set up
Bonus View
11
9
11
C
care
change settings
chapter
connect
audio from TV
guide
other devices
TV
connectors
contact us
4
15
12
8, 14
7
8
7
7
20
D
disc
play
supported discs
disposal of your product
DivX
character set
11
18
4
12
E
EasyLink
settings
14, 16
F
file formats
18
H
HDMI CEC (see Easylink)
14
EN
21
Eng lis h
The contents of a USB storage device cannot be
read.
•• Ensure that the format of the USB storage
device is compatible with the home theater
(see ‘Product specifications’ on page 18).
•• Ensure that the USB storage device
is formatted with a file system that is
supported by the home theater.
‘No entry’ or ‘x’ sign appears on the TV.
•• The operation is not possible.
EasyLink feature does not work.
•• Ensure that the home theater is connected
to a Philips brand EasyLink TV and that
EasyLink is on.
I do not want my home theater to be switched
on when I switch on my TV.
•• This is the correct behavior for Philips
EasyLink (HDMI-CEC). To make the home
theater work independently, switch off
EasyLink.
I cannot access BD-Live features.
•• Check the network connection or ensure
that the network has been set (see ‘Set up
network’ on page 9)up.
•• Clear memory storage. (see ‘Change
advanced settings’ on page 17)
•• Ensure that the Blu-ray disc supports BDLive feature.
My 3D video plays in 2D mode.
•• Ensure that your home theater is connected
to your 3D TV through HDMI.
•• Ensure that your disc is a Blu-ray 3D disc.
•• Ensure that the [Blu-ray 3D video] setting
is turned on.
I see black video on my TV screen.
•• Ensure that your home theater is connected
to the TV through HDMI.
•• Switch to the correct HDMI source on your
TV.
I
Internet
BD-Live
11
L
language
audio
disc menu
on-screen display
subtitle
12, 16
16
16
12, 16
M
MP3
play
14
N
network
set up
O
one-touch play
one-touch standby
overview
connectors
main unit
remote control
P
password (PIN code)
picture
options
rotate
slide show
troubleshooting
picture-in-picture
2nd audio language
2nd subtitle language
enable
play
2D video
3D video
disc
MP3 player
options
radio
troubleshooting
USB storage device
product care
product specifications
9
14, 16
14, 16
7
5
5
16
13
13
13, 13
20
11
11
11
12
12
11
14
11
13
20
12
4
18
R
radio
play
22
EN
program
tune
recycle
region code
remote control
repeat
rotate pictures
S
safety
settings
audio
EasyLink
parental control
preferences
slideshow
animation
duration
play musical slideshow
software
update
version
sound
mode
surround
treble and bass
troubleshooting
subtitle
language
subtitle shift
system audio control
T
time search video
title
troubleshooting
TV
audio from TV
connect
3
15
16
16
16
13
13
13
17
17
10
10
10
20
12, 16
12, 16
14
12
12
20
8, 14
7
U
USB
play
software update
12
18
V
video
options
synchronize with audio
W
13
13
13
4
18
5
12, 11
13
wireless
12
10
W,/>/W^KE^hDZ>/&^dz>
tZZEdzWK>/z&KZh^dZ>/
ĨĨĞĐƚŝǀĞϭƐƚ:ƵůLJϮϬϭϬ
WŚŝůŝƉƐƉƌŽǀŝĚĞƐŝƚƐŽŶƐƵŵĞƌůĞĐƚƌŽŶŝĐƐƉƌŽĚƵĐƚƐǁŝƚŚĂϭzĞĂƌDĂŶƵĨĂĐƚƵƌĞƌƐtĂƌƌĂŶƚLJ͘
dŚĞďĞŶĞĨŝƚƐŐŝǀĞŶƚŽƚŚĞƉƵƌĐŚĂƐĞƌďLJƚŚŝƐǁĂƌƌĂŶƚLJĂƌĞŝŶĂĚĚŝƚŝŽŶƚŽĂůůŽƚŚĞƌƌŝŐŚƚƐĂŶĚƌĞŵĞĚŝĞƐ͕ǁŚŝĐŚƚŚĞ
ƉƵƌĐŚĂƐĞƌŚĂƐŝŶƌĞƐƉĞĐƚŽĨƚŚĞƉƌŽĚƵĐƚƵŶĚĞƌƚŚĞdƌĂĚĞWƌĂĐƚŝĐĞƐĐƚŽƌŽƚŚĞƌŽŵŵŽŶǁĞĂůƚŚŽƌ^ƚĂƚĞ>Ăǁ͘
dŚĞĐŽŶĚŝƚŝŽŶƐĐŽŶƚĂŝŶĞĚŝŶƚŚŝƐǁĂƌƌĂŶƚLJƌĞƉůĂĐĞĂŶĚŽǀĞƌƌŝĚĞƚŚĞƉƌŽǀŝƐŝŽŶŽĨƚŚĞWŚŝůŝƉƐtŽƌůĚͲtŝĚĞ'ƵĂƌĂŶƚĞĞĨŽƌ
ƉƌŽĚƵĐƚƐƉƵƌĐŚĂƐĞĚŝŶƵƐƚƌĂůŝĂĂŶĚƵƐĞĚŝŶƵƐƚƌĂůŝĂ͘
WůĞĂƐĞƌĞĐŽƌĚƚŚĞĨŽůůŽǁŝŶŐŝŶĨŽƌŵĂƚŝŽŶĨŽƌLJŽƵƌƌĞĐŽƌĚƐĂŶĚŬĞĞƉŝŶĂƐĂĨĞƉůĂĐĞ͘
/ƚŝƐĞƐƐĞŶƚŝĂůƚŚĂƚLJŽƵƌĞƚĂŝŶLJŽƵƌŽƌŝŐŝŶĂůƉƵƌĐŚĂƐĞƌĞĐĞŝƉƚƚŽŵĂŬĞĂǁĂƌƌĂŶƚLJĐůĂŝŵ͘
DŽĚĞůŶƵŵďĞƌ ^ĞƌŝĂůŶƵŵďĞƌ ĂƚĞŽĨƉƵƌĐŚĂƐĞ
ZĞƚĂŝůĞƌ
WƵƌĐŚĂƐĞWƌŝĐĞ ͙͙͙͙͙͙͙͙͙͙͙͙͙͙͙͙͙͙͙͙͙͗͘͘
͙͙͙͙͙͙͙͙͙͙͙͙͙͙͙͙͙͙͙͙͙͗͘͘
͙͙͙͙͙͙͙͙͙͙͙͙͙͙͙͙͙͙͙͙͙͗͘͘
͙͙͙͙͙͙͙͙͙͙͙͙͙͙͙͙͙͙͙͙͙͗͘͘
͗͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘
/ĨLJŽƵƌĞƋƵŝƌĞĂƐƐŝƐƚĂŶĐĞǁŝƚŚƚŚĞŽƉĞƌĂƚŝŽŶŽĨƚŚĞƉƌŽĚƵĐƚ͕ŝƚƐĨĞĂƚƵƌĞƐŽƌƐƉĞĐŝĨŝĐĂƚŝŽŶƐ͕ƉůĞĂƐĞĐĂůůƚŚĞWŚŝůŝƉƐ
ŽŶƐƵŵĞƌĂƌĞĞŶƚƌĞŽŶϭϯϬϬϯϲϯϯϵϭǁŚĞƌĞƐƵƉƉŽƌƚŝƐƉƌŽǀŝĚĞĚďLJŽƵƌƚƌĂŝŶĞĚƐƚĂĨĨ͘
/ĨLJŽƵƌƉƌŽĚƵĐƚĚĞǀĞůŽƉƐĂĨĂƵůƚĚƵƌŝŶŐƚŚĞϭϮŵŽŶƚŚǁĂƌƌĂŶƚLJƉĞƌŝŽĚĂŶĚŚĂƐĂƉƵƌĐŚĂƐĞƉƌŝĐĞŽĨůĞƐƐƚŚĂŶΨϮϱϬ͕ƉůĞĂƐĞ
ƌĞƚƵƌŶƚŚĞĨĂƵůƚLJƉƌŽĚƵĐƚďĂĐŬƚŽƚŚĞƉůĂĐĞŽĨƉƵƌĐŚĂƐĞ͘
/ĨLJŽƵƌƉƌŽĚƵĐƚĚĞǀĞůŽƉƐĂĨĂƵůƚĚƵƌŝŶŐƚŚĞϭϮŵŽŶƚŚǁĂƌƌĂŶƚLJƉĞƌŝŽĚĂŶĚŚĂƐĂƉƵƌĐŚĂƐĞƉƌŝĐĞŽĨŵŽƌĞƚŚĂŶΨϮϱϬ͕ŽƌŝĨ
LJŽƵǁŽƵůĚůŝŬĞƚŽĚŝƐĐƵƐƐĂƌĞƉĂŝƌŽƉƚŝŽŶƐĨŽƌĂŶŽƵƚŽĨǁĂƌƌĂŶƚLJƌĞƉĂŝƌ͕ƉůĞĂƐĞĐĂůůϭϯϬϬϯϲϭϯϵϮĨŽƌLJŽƵƌŶĞĂƌĞƐƚWŚŝůŝƉƐ
ƵƚŚŽƌŝƐĞĚ^ĞƌǀŝĐĞĞŶƚƌĞ͘
ŽŶĚŝƚŝŽŶƐŽĨtĂƌƌĂŶƚLJ
Ă͘ &ŽƌƉƌŽĚƵĐƚƐǁŝƚŚĂƉƵƌĐŚĂƐĞƉƌŝĐĞŽĨůĞƐƐƚŚĂŶΨϮϱϬ͕ĐůĂŝŵƐĨŽƌǁĂƌƌĂŶƚLJĐĂŶŽŶůLJďĞŵĂĚĞĂƚƚŚĞƉůĂĐĞŽĨƉƵƌĐŚĂƐĞ͘
ĐŽƉLJŽĨƚŚĞƉƵƌĐŚĂƐĞƌĞĐĞŝƉƚǁŝůůďĞƌĞƋƵŝƌĞĚ͘
ď͘ &ŽƌƉƌŽĚƵĐƚƐǁŝƚŚĂƉƵƌĐŚĂƐĞƉƌŝĐĞŽĨŵŽƌĞƚŚĂŶΨϮϱϬ͕ĐůĂŝŵƐĨŽƌǁĂƌƌĂŶƚLJĐĂŶŽŶůLJďĞŵĂĚĞĂƚĂWŚŝůŝƉƐƵƚŚŽƌŝƐĞĚ
^ĞƌǀŝĐĞĞŶƚƌĞ͘ĐŽƉLJŽĨƚŚĞƉƵƌĐŚĂƐĞƌĞĐĞŝƉƚǁŝůůďĞƌĞƋƵŝƌĞĚ͘
Đ͘ dŚĞǁĂƌƌĂŶƚLJƉĞƌŝŽĚŝƐǀĂůŝĚĨƌŽŵƚŚĞŽƌŝŐŝŶĂůĚĂƚĞŽĨƉƵƌĐŚĂƐĞŽĨƚŚĞƉƌŽĚƵĐƚ͘
Ě͘ dŚŝƐǁĂƌƌĂŶƚLJĞdžƚĞŶĚƐŽŶůLJƚŽĚĞĨĞĐƚƐŝŶŵĂƚĞƌŝĂůŽƌǁŽƌŬŵĂŶƐŚŝƉŽĐĐƵƌƌŝŶŐƵŶĚĞƌŶŽƌŵĂůƵƐĞŽĨƚŚĞƉƌŽĚƵĐƚǁŚĞŶ
ŽƉĞƌĂƚĞĚŝŶĂĐĐŽƌĚĂŶĐĞǁŝƚŚƚŚĞŝŶƐƚƌƵĐƚŝŽŶƐ͘
Ğ͘ WŚŝůŝƉƐŵĂLJ͕ĂƚŝƚƐĚŝƐĐƌĞƚŝŽŶĐŚŽŽƐĞƚŽƌĞƉĂŝƌŽƌƌĞƉůĂĐĞƚŚŝƐƉƌŽĚƵĐƚ͘
Ĩ͘ /ĨĂƌĞƉůĂĐĞŵĞŶƚƉƌŽĚƵĐƚŝƐƐƵƉƉůŝĞĚ͕ŝƚŝƐǁĂƌƌĂŶƚĞĚĨŽƌƚŚĞƌĞŵĂŝŶĚĞƌŽĨƚŚĞǁĂƌƌĂŶƚLJƉĞƌŝŽĚ͕ĨƌŽŵƚŚĞŽƌŝŐŝŶĂůĚĂƚĞ
ŽĨƉƵƌĐŚĂƐĞ͘
Ő͘ dŚŝƐDĂŶƵĨĂĐƚƵƌĞƌƐtĂƌƌĂŶƚLJŝƐůŝŵŝƚĞĚƚŽϯŵŽŶƚŚƐĨŽƌƉƌŽĚƵĐƚƐƵƐĞĚŝŶĐŽŵŵĞƌĐŝĂůĂƉƉůŝĐĂƚŝŽŶƐ͘
Ś͘ WƌŽĚƵĐƚĂĐĐĞƐƐŽƌŝĞƐĂƌĞĐŽǀĞƌĞĚďLJƚŚĞƐĂŵĞǁĂƌƌĂŶƚLJƉĞƌŝŽĚ͘/ĨĂŶĂĐĐĞƐƐŽƌLJŝƐĨĂƵůƚLJ͕ƉůĞĂƐĞĐŽŶƚĂĐƚƚŚĞWŚŝůŝƉƐ
ŽŶƐƵŵĞƌĂƌĞĞŶƚƌĞŽŶϭϯϬϬϯϲϯϯϵϭ͘
ŝ͘ dŚŝƐDĂŶƵĨĂĐƚƵƌĞƌƐtĂƌƌĂŶƚLJŝƐŶĞŝƚŚĞƌƚƌĂŶƐĨĞƌĂďůĞŶŽƌǀĂůŝĚŝŶĐŽƵŶƚƌŝĞƐŽƚŚĞƌƚŚĂŶƵƐƚƌĂůŝĂ͘
dŚŝƐtĂƌƌĂŶƚLJĚŽĞƐŶŽƚĐŽǀĞƌ͗Ͳ
Ă͘ ^ĞƌǀŝĐĞĐŽƐƚƐĂƌŝƐŝŶŐĨƌŽŵĨĂŝůƵƌĞƚŽĐŽƌƌĞĐƚůLJĂĚũƵƐƚƚŚĞĐŽŶƚƌŽůƐŽĨƚŚĞƉƌŽĚƵĐƚŽƌƚŽŽďƐĞƌǀĞƚŚĞŝŶƐƚƌƵĐƚŝŽŶƐ͕Žƌ
ŝŶƐƉĞĐƚŝŽŶƐƚŚĂƚƌĞǀĞĂůƚŚĂƚƚŚĞƉƌŽĚƵĐƚŝƐŝŶŶŽƌŵĂůǁŽƌŬŝŶŐŽƌĚĞƌ͘
ď͘ WƌŽĚƵĐƚĨĂŝůƵƌĞƐĐĂƵƐĞĚďLJŵŝƐƵƐĞ͕ŶĞŐůĞĐƚ͕ĂĐĐŝĚĞŶƚĂůďƌĞĂŬĂŐĞ͕ƚƌĂŶƐŝƚĚĂŵĂŐĞ͕ƌĞƉĂŝƌƐŽƌŵŽĚŝĨŝĐĂƚŝŽŶďLJƵŶͲ
ĂƵƚŚŽƌŝƐĞĚƉĞƌƐŽŶƐ͕ĞdžƚĞƌŶĂůĨŝƌĞƐ͕ůŝŐŚƚŶŝŶŐƐƚƌŝŬĞƐ͕ĨůŽŽĚƐ͕ǀĞƌŵŝŶŝŶĨĞƐƚĂƚŝŽŶŽƌůŝƋƵŝĚƐƉŝůůĂŐĞ͘
Đ͘ dsŽƌƌĂĚŝŽƐŝŐŶĂůƌĞĐĞƉƚŝŽŶƉƌŽďůĞŵƐ͕ƌĞƉůĂĐĞŵĞŶƚŽĨǁŽƌŶŽƌƵƐĞĚďĂƚƚĞƌŝĞƐŽƌŽƚŚĞƌĐŽŶƐƵŵĂďůĞƐ͘
Ě͘ ^ĞĐŽŶĚŚĂŶĚŽƌƌĞĨƵƌďŝƐŚĞĚƉƌŽĚƵĐƚƐ͘
Ğ͘ WƌŽĚƵĐƚƐƐŽůĚŽŶƚŚĞŝŶƚĞƌŶĞƚŽƌŽŶůŝŶĞ͘
Ĩ͘ WƌŽĚƵĐƚĨĂŝůƵƌĞ͕ĐĂƵƐĞĚďLJŽƚŚĞƌƉƌŽĚƵĐƚƐ͘
Ɛƚ
sĞƌƐŝŽŶϭ͘ϱ͗ϭ :ƵůLJϮϬϭϬ
australia warranty.indd 1
8/24/2010 8:44:28 AM
Language Code
Abkhazian
6566
Afar
6565
Afrikaans
6570
Amharic
6577
Arabic
6582
Armenian
7289
Assamese
6583
Avestan
6569
Aymara
6589
Azerhaijani
6590
Bahasa Melayu
7783
Bashkir
6665
Belarusian
6669
Bengali
6678
Bihari
6672
Bislama
6673
Bokmål, Norwegian
7866
Bosanski
6683
Brezhoneg
6682
Bulgarian
6671
Burmese
7789
Castellano, Español
6983
Catalán
6765
Chamorro
6772
Chechen
6769
Chewa; Chichewa; Nyanja 7889
9072
中文
Chuang; Zhuang
9065
Church Slavic; Slavonic 6785
Chuvash
6786
Corsican
6779
Česky
6783
Dansk
6865
Deutsch
6869
Dzongkha
6890
English
6978
Esperanto
6979
Estonian
6984
Euskara
6985
6976
Faroese
7079
Français
7082
Frysk
7089
Fijian
7074
Gaelic; Scottish Gaelic 7168
Gallegan
7176
Georgian
7565
Gikuyu; Kikuyu
7573
Guarani
7178
Gujarati
7185
Hausa
7265
Herero
7290
Hindi
7273
Hiri Motu
7279
Hrwatski
6779
Ido
7379
Interlingua (International)7365
Interlingue
7365
Inuktitut
7385
1_HTS5220_12_EN-US.indd Sec2:33
Inupiaq
Irish
Íslenska
Italiano
Ivrit
Japanese
Javanese
Kalaallisut
Kannada
Kashmiri
Kazakh
Kernewek
Khmer
Kinyarwanda
Kirghiz
Komi
Korean
Kuanyama; Kwanyama
Kurdish
Lao
Latina
Latvian
Letzeburgesch;
Limburgan; Limburger
Lingala
Lithuanian
Luxembourgish;
Macedonian
Malagasy
Magyar
Malayalam
Maltese
Manx
Maori
Marathi
Marshallese
Moldavian
Mongolian
Nauru
Navaho; Navajo
Ndebele, North
Ndebele, South
Ndonga
Nederlands
Nepali
Norsk
Northern Sami
North Ndebele
Norwegian Nynorsk;
Occitan; Provencal
Old Bulgarian; Old Slavonic
Oriya
Oromo
Ossetian; Ossetic
Pali
Panjabi
Persian
Polski
Português
7375
7165
7383
7384
7269
7465
7486
7576
7578
7583
7575
7587
7577
8287
7589
7586
7579
7574
7585
7679
7665
7686
7666
7673
7678
7684
7666
7775
7771
7285
7776
7784
7186
7773
7782
7772
7779
7778
7865
7886
7868
7882
7871
7876
7869
7879
8369
7868
7878
7967
6785
7982
7977
7983
8073
8065
7065
8076
8084
Pushto
Russian
Quechua
Raeto-Romance
Romanian
Rundi
Samoan
Sango
Sanskrit
Sardinian
Serbian
Shona
Shqip
Sindhi
Sinhalese
Slovensky
Slovenian
Somali
Sotho; Southern
South Ndebele
Sundanese
Suomi
Swahili
Swati
Svenska
Tagalog
Tahitian
Tajik
Tamil
Tatar
Telugu
Thai
Tibetan
Tigrinya
Tonga (Tonga Islands)
Tsonga
Tswana
Türkçe
Turkmen
Twi
Uighur
Ukrainian
Urdu
Uzbek
Vietnamese
Volapuk
Walloon
Welsh
Wolof
Xhosa
Yiddish
Yoruba
Zulu
8083
8285
8185
8277
8279
8278
8377
8371
8365
8367
8382
8378
8381
8368
8373
8373
8376
8379
8384
7882
8385
7073
8387
8383
8386
8476
8489
8471
8465
8484
8469
8472
6679
8473
8479
8483
8478
8482
8475
8487
8571
8575
8582
8590
8673
8679
8765
6789
8779
8872
8973
8979
9085
4/14/2010 10:24:07 AM
© 2010 Koninklijke Philips Electronics N.V.
All rights reserved.
sgpam_1037/98_v2
bk.indd Sec4:48
1/12/2010 2:54:37 PM
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising