Terzismo | GSH5530ZXWW | Terzismo GSH5530ZXWW User manual

Terzismo GSH5530ZXWW User manual
Installation – Use – Maintenance
GSH 5530 TXWW
GSH 5530 ZXWW
DISHWASHER
CONTENTS
Safety advice
Setting up, installation
Water softener unit
Adjusting the upper basket
Loading the dishes
Information for test laboratories
Half load washing
Loading the detergent and rinse aid
Cleaning the filters
Some practical hints
Routine cleaning and maintenance
Description of the control panel
Technical data
Operating the programmes and special functions
Programme selection
Identifying minor faults
pag.
pag.
pag.
pag.
pag.
pag.
pag.
pag.
pag.
pag.
pag.
pag.
pag.
pag.
pag.
pag.
4
5
9
11
12
14
15
16
18
19
20
21
21
22
24
26
Fig. A
5
1
4
2
3
Please read the instructions in this booklet carefully because they contain important
information on how to install, use and maintain your dishwasher safely as well as
containing useful tips on how to make the most of it.
Keep this booklet safe for future reference.
3
SAFETY INSTRUCTIONS
WARNING !
Knives and other utensils with sharp
points must be loaded in the basket
with their points down or placed in a
horizontal position.
There are certain basic safety rules
which are valid for any domestic
appliance.
Installation
Daily use
■ Make sure that the plug fitted to the
machine is compatible with the power
supply socket. If it is not, get a suitably
qualified person to fit the correct type,
and to make sure that the cables to the
mains socket are able to cope with the
power rating of the appliance.
■ This appliance is be designed for domestic
use only.
■ The dishwasher is designed for normal
kitchen utensils.
Objects that have been contamined by
petrol, paint, traces of steel or iron,
corrosive chemicals, acids or alkalis
must not be washed in the dishwasher.
■ Ensure that the dishwasher does not
crush power cables.
■ In general it is not advisable to use
adaptors, multiple plugs and/or extension
cables.
INSTALLATION
Electrical connection
(Technical notes)
This appliance complies with international
safety standards, and is fitted with a plug
with earth connection to ensure complete
earthing of the product.
■ After unpacking, adjust the height of the
dishwasher. For the dishwasher to work
correctly it must be level. Adjust the feet
so that the machine does not tilt by more
than 2 degrees.
Before connecting the appliance to the
mains supply it is important to ensure:
■ If it you need to move the machine after
removing the packaging, do not try to lift
it by the bottom of the door. Follow the
instructions in the figure below. Open the
door slightly and lift the machine by
holding on the top.
1. that the supply socket is properly
earthed;
2. that your electricity supply is capable of
meeting the consumption requirements
listed on the rating plate of your
appliance.
■ If there is a water softening device installed
in the home there is no need to add
salt to the water softener fitted in the
dishwasher.
■ Should it be necessary to replace the
supply cord, call the After Sales Service
Centre.
WARNING!
Ensure that your product is properly
earthed.
In the absence of adequate earthing
you will notice that when touching
the metal parts of your appliance an
electrical dispersion can be felt, due
to the presence of a radio interference
suppressor.
■ Cutlery is washed best if it is placed in
the basket with the handles downwards.
■ If the appliance breaks down or stops
working properly, switch it off, turn off the
water supply and do not tamper with it.
Repair work should only be carried out
by an approved service agent and only
genuine spare parts should be fitted. Any
failure to follow the above advice may
have serious consequences for the safety
of the appliance.
Safety
■ Never touch the appliance when your
hands or feet are wet or damp.
■ Do not use when your feet are bare.
■ Do not remove the plug from the mains
supply socket by pulling the mains cable
or the machine itself.
Disposal
■ Do not leave the appliance exposed to
the elements (rain, sun etc).
IMPORTANT
When the appliance is located on a
carpet floor, attention must be paid to
ensure that there is no obstruction to
the bottom vents.
Manufacturer declines all responsibility
for any damage due to non-earthing of
the machine.
Make sure that the plug on the
appliance remains accessible after
installation.
This appliance complies with
Directives 89/336/EEC, 73/23/EEC
and following changes.
■ The dishwasher has been made from
materials which can be recycled so that it
can be disposed of in an environmentally
friendly way.
■ Do not let children (or others incapable
of operating it) use the machine without
supervision.
■ If you wish to dispose of an old dishwasher
be careful to remove the door to
eliminate the risk of children becoming
trapped inside it.
■ Water left in the machine or on the
dishes at the end of the wash programme
should not be swallowed.
■ The door should not be left in the open
position since this could present a potential
hazard ( es. tripping ).
■ Leaning or sitting on the open door of
the dishwasher could cause it to tip over.
4
5
Water connection
■ The hose can be hooked over the side of
the sink, but it must not be immersed in
water, in order to prevent water from
being syphoned back to the machine
when this is in operation (fig. 4Y).
Connecting the outlet hose
IMPORTANT
The appliance must be connected to
the water mains using new hose-sets.
The old hose-sets should not be reused.
1
■ The outlet hose should disharge into a
standpipe, making sure that there are no
kinks (fig. 4).
■ When installing the appliance under a
worktop the hose pipe clamp must be
attached to the wall in the highest possible
position under the worktop (fig. 4Z).
■ The standpipe must be at least 40 cm
above floor level and it must have an
internal diameter of at least 4 cm.
■ The inlet and drain hoses can be directed
to left or right.
■ Check that there are no kinks in the inlet
and outlet hoses.
■ It is advisable to fit an anti-odour air trap
(fig. 4X).
IMPORTANT
The dishwasher can be connected to
either cold or hot water, as long as it
is no hotter than 60 °C.
2
■ Water pressure must be between
0,08 MPa and 0,8 MPa. If the pressure is
below the minimum consult our service
department for advice.
■ The inlet hose must be connected to a
tap so that the water supply can be cut
off when the machine is not in use
(fig. 1 B).
■ If necessary the outlet hose can be
extended up to 2,5 m, provided that it is
kept at a maximum height of 85 cm
above floor level. The extension pipe is
available from the After Sales Service
Centre.
4
■ The dishwasher is fitted with 3/4" threaded
connector (fig. 2).
■ Connect inlet hose “A” to water tap “B”
with a 3/4" attachment making sure that
it has been properly tightened.
■ If it is necessary, the inlet pipe can be
lengthened up to 2,5 m. The extension
pipe is available from the After Sales
Service Centre.
3
■ If limescale deposits or sand are present
in the water, it is advisable to obtain the
appropriate filter, art. 9226085, from the
After Sales Service Centre (fig. 3). The
filter “D” must be inserted between the tap
“B” and the inlet hose “A”, remembering
to fit the washer “C”.
■ If the dishwasher is connected to new
pipes or to pipes which have not been in
use for a long time run water through for
a few minutes before connecting the
inlet hose. In this way no deposits of
sand or rust will clog up the water inflow
filter.
6
7
INSTALLATION IN FITTED
KITCHENS
Underneath existing work top
(when fitting beneath a work top)
Fitting between existing cabinets
■ In most modern fitted kitchens there is
only one single work top under which
cabinets and electrical appliances are
fitted. In this case remove the work top
of the dishwasher by unscrewing the
screws under the rear edge of the top
(fig. 6).
■ The height of the dishwasher, 85 cm, has
been designed in order to allow the
machine to be fitted between existing
cabinets of the same height in modern
fitted kitchens. The feet can be adjusted
so that correct height is reached.
■ The height will then be reduced to 82 cm,
as scheduled by the International
Regulations (ISO) and the dishwasher
will fit perfectly under the kitchen
working top (fig. 7).
■ The laminated top of the machine does
not require any particular care since it is
heatproof, scratchproof and stainproof
(fig. 5).
■ The work top can be easily adjusted to
line it with the top of existing cabinets;
this is done by moving it by 5 mm each
time up to a maximum of 25 mm.
If your water is at level 0, you need not use
any regenerating salt, nor need you make
any adjustment, as your water is soft.
Depending on the source of the supply,
water contains varying amounts of limestone
and minerals which are deposited on the
dishes leaving whitish stains and marks.
The higher the level of these minerals
present in the water, the harder the water is.
The dishwasher is fitted with a water
softener unit which, through the use of
special regenerating salt, supplies
softened water for washing the dishes.
The softener unit can treat water with a
hardness of up to 60°fH (French grading)
or 33°dH (German grading) through five
different settings.
The degree of hardness of your water can
be obtained from your water supply
company.
According to the degree of hardness of
your water, regulate the softener unit in the
following way:
1. remove the lower rack. Unscrew and
remove the cap from the salt dispenser
located in the bottom of the tub
(fig. A"1");
2. turn the selector screw to the required
position with a blunt screwdriver or
similar blunt instrument.
Regulating the water softener
■ To adjust it, unscrew the two screws at
the back and fix the top in the position
required (fig. 6).
5
WATER SOFTENER UNIT
TYPE 1
The table below lists different degrees of
water hardness with the corresponding setting for the softener unit.
6
*The water softener unit is set in the
factory at level 2, as this is suitable for the
majority of users.
7
TYPE 2
598
Opening the door
556/573
Closing the door
Put your hand into the recess and pull.
If the machine comes open while it is working,
an electrical safety device automatically
switches everything off.
Place the baskets in the machine.
Make sure that both the spray arms are
free to rotate and are not obstructed by
cutlery, crockery or pans. Close the door,
pressing on it to make sure it is firmly shut.
Level
Water
hardness
°fH
(French)
0
1
*2
3
4
0-9
10-30
31-40
41-50
51-60
Water
hardness
Use of
regenerating
°dH
salt
(German)
0-5
6-16
17-22
23-27
28-33
NO
YES
YES
YES
YES
IMPORTANT
For the machine to work properly,
the door should not be opened while
it is in operation.
8
9
Water
softener
setting
FREE
N.1
N.2
N.3
N.4
position
position
position
position
N°
of
washes
50
40
30
20
use of the appliance, it should be refilled
from time to time according to the
regulation of the water softener unit.
Loading the salt
■ On the bottom of the machine there is a
container for the salt for regenerating
the softener.
IMPORTANT
(Only for first start up)
When the appliance is used for the
first time, after completely filling the
salt container, it is necessary to add
water until the container overflows.
■ It is important to use only a salt that is
specifically designed for dishwasher.
Other types of salt contain small quantities
of insoluble particles which over a long
period of time may affect and deteriorate
the softener performance.
Adjustment of the upper
basket
If 27 cm to 31 cm plates are normally used,
load them onto the lower basket after the
upper basket has been placed in its upper
position and proceed as detailed below:
A
1. Turn the front stops “A” outwards;
■ To add salt, unscrew the cap of the container on the bottom and then refill the
container.
2. Take out the basket and remount it in the
upper position;
■ During this operation a little water will
overflow; but keep adding salt until the
container is full. When the container is
full, clean the thread of salt residue and
retighten the tap.
3. Replace the blocks “A” in their original
position.
■ After loading the salt, it is recommended
running a complete washing cycle,
or COLD RINSE programme.
The salt dispenser has a capacity of
between 1.5 and 1.8 kg and, for efficient
Dishes that are bigger than 20 cm in
diameter can no longer be loaded onto the
upper basket and the mobile supports
cannot be used when the basket is in the
upper position.
A
Salt loading indicator
This model is provided with a blind cap. In
this case, the salt level must be checked
periodically, according to the regulation of
the water softener unit.
IMPORTANT
The appearance of white stains on
dishes is generally an important
sign that the salt container needs
filling.
10
11
■ Salad bowls and plastic bowls may also
be loaded on the upper basket. It is
advisable to block these in place so that
the jets of water do not make them
overturn.
LOADING DISHES
Using the upper basket
A standard daily load is represented in figs. 1, 2 and 3.
1
A
■ The upper basket has been designed to
offer maximum flexibility in use and can
be loaded with up to 24 plates on two
rows, up to 30 glasses on five rows or a
mixed load.
■ The upper basket is provided with mobile racks hooked to the sides of the
basket which can be regulated in two
positions: upright and lowered. In the
lowered position the racks may be used
for tea and coffee cups, kitchen knives
and ladles. Glasses with stems may be
safely hung on the ends of the racks.
Glasses, cups, saucers and dessert
plates may be loaded under the racks.
C
B
D
F
Using the lower basket
■ Saucepans, oven dishes, tureens, salad
bowls, lids, serving dishes, dinner
plates, soup plates and ladles can be
loaded on the lower basket.
■ Soup plates and ordinary plates may be
loaded with the rack in the upright
position. Plates should be loaded
vertically with the underside of the plate
towards the back of the dishwasher with
a space between each plate to allow
water to pass freely.
■ Place the cutlery holder on the lower
basket (fig. 3), making sure that the
cutlery does not get in the way of the
rotating arms.
■ Plates may be loaded in a single row
(fig. 1) or on both rows (fig. 2).
IMPORTANT
The lower basket has a safety-stop
device, for its safe extraction, also
especially useful with a full load.
For loading salt, cleaning filter and for
ordinary maintenance, the complete
extraction of the basket is necessary.
■ It is advisable to load large plates
(approx. 27 or more cm) slightly tilted
towards the rear to facilitate introduction
of the basket into the machine.
Upper basket (fig. 2)
A = soup plates
B = dinner plates
C = dessert plates
D = saucers
E = cups
F = glasses with stems
G = glasses
H = single section cutlery basket
2
A
■ Place the cutlery in the plastic cutlery
holder with the handles pointing
upwards.
■ It is advisable to load plates of the same
size together in order to utilize maximum
basket capacity.
B
C
G D
H
3D
F E
F
F
A G
E
B
4
12
Upper basket (fig. 1)
A = soup plates
B = dinner plates
C = dessert plates
D = saucers
E = cups
F = glasses
E
C
Lower basket (fig. 3)
A = medium-sized saucepan
B = large saucepan
C = frying pan
D = lids
E = tureens, serving dishes
F = cutlery
G = oven dishes
Please load the dishwasher sensibly to ensure the
best wash results.
Cutlery basket (fig. 4)
The cutlery basket is made with two detachable
parts which will enable various loading options. The
two parts can be detached by sliding the left section
away from the right section.
13
INFORMATION FOR THE TEST LABORATORIES
Half load wash upper basket
General programme comparison (Ref. EN 50242 Standards)
1
(see programmes selection)
1. Upper basket position: low
2. Normal load
3. Shine setting: 6
4. Amount of detergent:
- 8 g for pre-wash;
- 22 g for wash.
C
Correct loading is indicated, in fig. 5 for the upper basket, in fig. 6 for the lower
basket and in fig. 7 for the cutlery basket.
5
G
C
E
C
H
B
C
I
D F
H
A
6
M
N
P
Upper basket (fig. 5)
A = 5 + 5 + 2 glasses
B = 12 saucers
C = 4 + 4 + 4 cups
D = small bowl
E = medium bowl
F = large bowl
G = 1 + 1 forks
H = 1 + 1 serving spoons
I = 3 + 3 + 3 + 3 dessert spoons
L = 3 + 3 + 3 + 3 teaspoons
N
B
I
H
E
2
A
C
F
D
B
H
E
I
L
Q
D
F
G
12 international place load (Ref. EN 50242)
1/2 mixed load (fig. 1)
A = glasses
B = cups
C = soup plates
D = dessert plates
E = saucers
F = saucepan
G = Irying pan
H = medium bowl
I = small bowl
A
1/2 load standard (fig. 2)
A = 6 glasses
B = 6 cups
C = serving dish
D = 6 soup plates
E = 6 dinner plates
F = 6 dessert plates
G = 6 saucers
H = medium bowl
I = small bowl
G A
Lower basket (fig. 6)
M = 8 + 4 soup plates
N = 11 + 1 dinner plates
O = 12 dessert plates
P = serving dish
Q = cutlery
Place the cutlery in the plastic cutlery holder on the lower basket.
M
7
R
O
Cutlery basket (fig. 7)
Place the side racks in the lower position
and fill with 6 + 6 knives(R); in the spaces
left insert cutlery with the handles down.
Take care not to load more than two different
types of cutlery in the same compartment.
14
15
■ the effectiveness of detergents containing
the built in water softener/salt depends
on the hardness of your water supply.
Check that the hardness of your water
supply is within the effective range given
on the detergent packaging.
LOADING THE DETERGENT
AND THE RINSE AID
Filling the detergent container
Should this occur, we would recommend
using traditional separate products – salt,
detergent and rinse agent. This will ensure
that the water softener in the dishwasher
operates correctly.
Please note that on return to the use of
conventional salt, a number of cycles will
be required before the system becomes
fully efficient again.
In certain circumstances use of combined
detergents can cause:
IMPORTANT
It is essential to use a detergent
that is specifically designed for
dishwashers either in powder, liquid
or tablet form.
B
After pouring the detergent into the container,
close the lid, firstly pushing (1) and then
pressing on it (2) until you hear the click.
■ limescale deposits on dishes or in the
dishwasher;
IMPORTANT
Any problems which arise as a direct
result of the use of these products
are not covered by our warranty.
■ a reduction in washing and drying
performance.
Unsuitable detergents (like those for
washing up by hand) do not contain the
proper ingredients for use in a dishwasher,
and stop the dishwasher from working
correctly.
Filling the rinse aid container
Normal wash
The detergent container is inside the door
(fig. A “2”). If the lid of the container is
closed, press the button (A) to open.
At the end of every wash cycle the lid is
always open and ready for the next time
the dishwasher is used.
WARNING!
When loading the lower basket, please
ensure that the plates or others do not
obstruct the detergent dispenser.
The amount of detergent to be used varies
according to how dirty the dishes are and
on the type of dishes to be washed.
We advise using 20÷30 g of detergent in the
wash section of detergent compartment (B).
C
The rinse aid, which is automatically
released during the last rinsing cycle, helps
the dishes to dry quickly and prevents
spots and stains forming.
The rinse aid container can be found to the
left of the detergent container (fig. A "3").
Since not all detergents are the same the
instructions on the boxes of detergent can
vary. We should just like to remind users
that too little detergent does not clean the
dishes properly whilst too much detergent
will not produce better results and is also a
waste.
To open the lid, push the reference mark
and, in the same time, pull the tab of
opening.
IMPORTANT
Do not use an excessive amount of
detergent and help limit damage to
the environment at the same time.
It is always advisable to use rinse aid that
is specifically designed for dishwasher.
Check the rinse aid level through the
indicator eye (C) which is located on the
dispenser.
FULL
EMPTY
dark
light
Regulating the rinse aid from 1 to 6
CAUTION!
IMPORTANT NOTE ON THE USE OF
COMBINED DETERGENTS
If you are planning to use combined detergents
i.e. those with built in salt and/or rinse
agent, we would advise the following:
■ read carefully and follow the manufacturer’s
instructions given on the packaging;
■ some combined detergents, particularly
those with built in rinse agent, provide
best results when used with specific
programmes;
A
16
The regulator (D) is placed under the lid
and can be turned using a coin.
The recommended position is 4.
The limestone content of the water
considerably affects the formation of
limescale and the drying performance.
It is therefore important to regulate the
quantity of rinse aid to achieve good
washing results.
If, after the wash, streaks occur on the
dishes, decrease the amount by one
position. If whitish spots occur, increase the
amount by one position.
D
17
CLEANING THE FILTERS
PRATICAL HINTS
The filter system (fig.A “4”) consists of:
1
a central container that traps the larger
particles;
a flat gauze that continuously filters the
wash water;
■ Before placing the dishes in the
dishwasher, remove any remaining
food (bones, shells, pieces of meat or
vegetables, coffee grounds, skin of fruit,
cigarette ash, tooth picks etc. to avoid
blocking the filters, water outlet and
washing arm nozzles.
■ Try not to rinse the dishes before
loading them into the dishwasher.
■ To achieve excellent results every time,
the filters should be checked and
cleaned after each wash.
■ If saucepans and oven dishes are
encrusted with the remains of burnt or
roast food, it is advisable to leave them
to soak before washing.
■ To remove the filter unit, simply turn the
handle anticlockwise (fig. 1).
■ Place the dishes face downwards.
2
■ Remove the gauze filter (fig.3) and
wash the whole unit under a jet of
water. If necessary a small brush can
be used.
■ If you want the dishwasher to give a
complete wash, place the dishes in the
dishwasher at the end of each meal and
if necessary turn on the COLD RINSE
cycle to soften the food remains and
remove bigger particles of food from the
new load of dishes.
When the dishwasher is full start the
complete wash cycle programme.
How to get really good wash
results
a micro filter, located beneath the gauze,
that traps the tiniest particles ensuring a
perfect rinse.
■ For ease of cleaning, the central container
is removable (fig. 2).
How to make savings
■ If the dishes are not very dirty or if the
baskets are not very full select an
ECONOMY programme, following the
instructions in the program list.
What not to wash
■ It should be remembered that not all
dishes are suitable for washing in a
dishwasher.We advise against using
the dishwasher to wash items in
thermoplastic, cutlery with wooden or
plastic handles, saucepans with
wooden handles, items in aluminium,
crystal, leaded glass unless otherwise
stated.
■ Try to place the dishes in such a way
that they are not touching one another.
If they are loaded properly you will get
better results.
■ After loading the dishes check that the
washing arms can rotate freely.
■ Certain decorations may fade. It is
therefore a good idea before loading the
whole batch to wash just one of the
items first so as to be sure that others
like it will not fade.
■ Pans and other dishes that have
particularly stubborn food particles or
remnants of burnt food should be left to
soak in water with dishwasher
detergent.
■ With the Self-cleaning Micro filter,
maintenance is reduced and the filter
unit need only be checked every two
weeks. Nevertheless, after each wash it
is advisable to check that the central
container and the gauze filter are not
clogged.
■ It is a good idea not to put silver cutlery
with non-stainless steel handles into
the dishwasher as there could be a
chemical reaction between them.
■ To wash silver properly:
a) rinse the silver immediately after
use, especially if it has been used for
mayonnaise, eggs, fish etc.;
WARNING!
After cleaning the filters, make sure
that they are correctly reassembled
and that the gauze filter is properly
positioned at the bottom of the
dishwasher.
3
IMPORTANT
When buying new crockery or
cutlery always make sure that they are
suitable for washing in a dishwasher.
b) do not sprinkle detergent onto it;
c) keep it separate from other metals.
Useful hints
Make sure that the filter is screwed
back, clockwise, into the gauze, as
poor seating of the filter unit could
have an adverse effect on the
efficiency of the appliance.
■ In order to avoid any dripping from the
top rack, remove the lower rack first.
IMPORTANT
Never use the dishwasher without
the filters.
■ If the dishes are to be left in the
machine for some time, leave the door
ajar, to let some air circulate and to
improve the drying performance.
18
19
CLEANING AND
MAINTENANCE
1
1b
DESCRIPTION OF THE CONTROL PANEL
■ To clean the dishwasher outside, do not
use solvents (degreasing action) neither
abrasives, but only a cloth soaked with
water.
■ The dishwasher does not require special
maintenance, because the tank is
self-cleaning.
■ Regularly wipe the door gasket with a
damp cloth to remove any food remains
or rinse aid.
A B
2
■ It is advisable to remove limestone
deposits or dirt periodically, by doing an
empty wash; pour a glass of vinegar on
the bottom of the tank and select the
light wash.
■ If, in spite of the routine cleaning of the
filters, you notice that the dishes or pans
are not properly washed or rinsed, check
that all the spray heads on the rotor
arms (fig. A “5”) are clear.
If they are blocked, clean them in the
following way:
C
D
E
A
"HALF LOAD" button
D
Programme selector
B
"ON/OFF" button
E
Indicator light "WASHING"
C
Door handle
WHEN CYCLE IS FINISHED
1. to remove the upper rotor arm, turn it
until it lines up with the stop marked
by the arrow (fig. 1). Push it upwards
(fig. 1b) and, keeping it pushed in,
unscrew it in a clockwise direction
(to reassemble it repeat the same
operation, but turn it anticlockwise).
The lower rotor arm can be removed
simply by pulling it upwards (fig. 2);
After every wash it is essential to turn off
water supply and to switch off the machine
by pressing the On/Off button to the off
position.
2. wash the rotor arms under a jet of water
to clear any blockage in the spray
heads;
1. do an empty wash with detergent in order
to clean the machine of any deposits;
If the machine is not going to be used for
some time, it is advisable to follow these
rules:
2. pull out the electric plug;
3. when you have finished, refit the rotor
arms in the same position, remembering
to re-align the arrow and screw into
position.
3. turn off the water tap;
4. fill the rinse aid container;
DIMENSIONS:
Height
Depth
Width
Depth with door open
with working top
without working top
85
60
60
120
82
55,6
59,8
117
cm
cm
cm
cm
TECHNICAL DATA:
5. Ieave the door ajar;
■ Both the door lining and the tank lining
are in stainless steel; however, should
spots caused by oxidation occur, this is
probably due to a high level of iron salts
presents in the water.
6. keep the inside of the machine clean;
7. If the machine is left in places where the
temperature is below 0°C any water left
inside the pipes may freeze. Wait until
the temperature rises above zero and
then wait for about 24 hours before
starting up the dishwasher.
■ The spots can be removed with a mild
abrasive agent; never use chlorine
based materials, steel wool, etc.
20
EN 50242 place load
Capacity with pans and dishes
Water supply pressure
Fuse
Power input
Supply voltage
12
8 persons
Min. 0,08 - Max 0,8 MPa
(see rating plate)
(see rating plate)
(see rating plate)
21
SELECTING THE PROGRAMME
AND SPECIAL FUNCTIONS
Interrupting a programme
Opening the door is not recommended
while a programme is running, especially
during the main washing phase and final
drying.
However, the dishwasher will stop automatically
when the door is opened.
If the door is opened during a programme,
the indicator light "WASHING" will start
flashing, up to when you re-close the door.
At this point, the programme will restart
from where it had been interrupted (if it is
necessary, the appliance will make a short
thermal anti-shock programme before).
(Use in conjunction with programme guide)
Setting a programme
WARNING!
Before to set any programme, the
programme selector must be in the
"RESET" position and the indicator
light "WASHING" (
) must be off.
Make sure that the "ON/OFF" ( )
button is pressed in.
If you wish to change or cancel the
programme that is running, carry out
the following:
turn the programme selector to "RESET"
position. After a few seconds the indicator
light "WASHING" will go off.
To set the programme, press the "ON/OFF"
button: then turn the dial (in a clockwise or
anti-clockwise direction) until the pointer
is in line with the number of the required
programme.
After about 4 seconds, the indicator light
"WASHING" will come on.
Setting of new programme
IMPORTANT
This dishwasher is equipped with an
anti-overflow safety device which will
automatically empty any excess
water should a problem occur.
Whenever you want to set a new programme,
you MUST turn the programme selector
to "RESET" position and wait for the
"WASHING" indicator light to go off.
Troubleshooting
WARNING!
To ensure the correct operation of
the anti-overflow safety device, it is
recommended not to move or to tilt
the dishwasher during operation.
If it is necessary to move or to tilt the
dishwasher, first make sure the
washing cycle is finished and that no
water is left in the tank.
While you are setting a programme, the
indicator light "WASHING" will start
flashing very quickly if the electronics
detect some incorrect programming function.
In this case, turn the programme selector to
the "RESET" position and the indicator light
"WASHING" will then go off. After this you
should again set the required programme.
If the malfunction continues, contact the
After Sales Service Centre.
A new wash setting can now be made.
WARNING!
Before starting a new programme,
you should check that there is still
detergent in the dispenser.
If necessary, top up the dispenser.
IMPORTANT
While a programme is running, the
programme selector will remain in
the selected position, and will NOT
MOVE.
If there is any break in the power supply
while the dishwasher is operating, a
special memory stores the selected
programme and, when the power is
restored, it continues where it left off.
Option buttons
"HALF LOAD" button
End of programme
By using this option, it is possible to wash
a smaller quantity of crockery: you should
load only the upper basket for dishes and
place cutlery in the tray in the bottom
basket.
This reduces water and energy consumption and requires a smaller quantity of
detergent.
At the end of the programme, the indicator
light "WASHING" will start flashing.
Turn the programme selector to "RESET"
position, wait until the indicator light
"WASHING" goes off and press the
"ON/OFF" button.
22
23
PROGRAMME SELECTION
INTENSIVE
Once a day - for heavily soiled pans and
any other items that have been left all day
for washing.
UNIVERSAL
Once a day - for normal soiled pans and
any other items that have been left all day
for washing.
A WASH 59’
Suitable for heavily soiled items that are to
be washed straight after a meal.
(Max 8 place load)
ECO
Energy Saving Programme suitable for
normal soiled items. Using detergents with
enzyme.
Programme standardised to EN 50242.
DELICATE
Suitable for delicate crockery and glassware.
Also for less soiled items excluding pans.
RAPID 29’
Quick wash for dishes which are to be
washed immediately after the meal. Wash
load of 4/6 persons.
Wash with soaking cycle (Prewash)
•
••
••
•
•
•
•
•
•
•
•
•
•
•
•
• •
• •
• •
• •
•
Hot rinse with rinse aid
Second cold rinse
75°C
• • •
65°C
•
70°C
45°C
45°C
50°C
N/A = OPTION NOT AVAILABLE
If setting the INTENSIVE programme, a second dose of about 20 g of detergent (1 table-spoon)
must be added directly in the dishwasher. For A WASH 59’ programme add 5 g.
24
First cold rinse
Main wash
Cold pre-wash
Hot pre-wash
Check salt container
Check rinse aid
dispenser
Clean filter
Detergent for washing
•
•
••••• •
25
•
•
•
•
•
•
“HALF LOAD” button
Short cold pre-wash for items that are
stored in the dishwasher until you are
ready to wash a full load.
Special function
buttons
available
With cold water (15°C)
(Tolerance ± 10%)
COLD RINSE
Detergent for soaking
(Prewash)
Description
Programme
Avarage
duration in
minutes
Programme contents
Check list
5
N/A
120
YES
95
YES
59
YES
140
YES
80
YES
29
N/A
IDENTIFYING MINOR FAULTS
FAULT
Should the dishwasher fail to operate, before contacting the Service Centre, make
the following checks:
FAULT
1 - Machine completely dead
2 - Machine does not
draw water
3 - Machine does not
discharge water
4 - Machine discharges
water continuously
5 - Spray arms are not heard
to rotate
6 - On electronic appliances
without a display: one or
more LED flashing quickly.
CAUSE
See causes for no. 5
Connect electric plug
O/I button has not been pressed
Press button
Door is open
Close door
No electricity
Check the fuse in the plug and
the electricity supply
See causes for no. 1
Check
Water tap is turned off
Turn water tap on
Programme selector is not at
correct position
Turn programme selector to
correct position
The inlet hose is bent
Eliminate the bends in the hose
The inlet hose filter is not
correctly connected
Clean the filter at the end of the
hose
Filter is dirty
Clean filter
Outlet hose is kinked
Straighten outlet hose
The outlet hose extension is
not correctly connected
Follow the instructions for
connecting the outlet hose
carefully
The outlet connection on the
wall is pointing downwards not
upwards
Call a qualified technician
Position of outlet hose is too
low
Lift outlet hose to at least 40 cm
above floor level
Excessive amount of detergent
Reduce amount of detergent
Use suitable detergent
Item prevents arms from rotating
Check
Plate and cup filter very dirty
Clean plate and cup filter
Water inlet tap turned off
Switch off the appliance.
Turn on the tap.
Re-set the cycle.
REMEDY
Check
Bottom of saucepans have not Burnt on food remains must
been washed well
be soaked before putting pans
in dishwasher
REMEDY
Plug is not connected to wall
socket
CAUSE
7 - Load of dishes is only
partially washed
Edge of saucepans have not
been washed well
Reposition saucepans
Spray arms are partially blocked
Remove spray arms by
unscrewing ring nuts clockwise
and wash under running water
The dishes have not been
properly loaded
Do not place the dishes too
closely together
The end of the outlet hose is in
the water
The end of the outlet hose
must not come into contact
with the outflow water
The incorrect amount of
Increase the measure
detergent has been measured
according to how dirty the
out; the detergent is old and hard dishes are and change detergent
The wash programme is not
thorough enough
Choose a more vigorous
programme
The lower basket dishes have
not been washed
Depress half load button
Water is too hard
8 - Presence of white spots
on dishes
9 - Noise during wash
10 - The dishes are not
completely dry
Check salt and rinse aid level
and regulate amount.
Should the fault persist,
Contact Service Centre
The dishes knock against one Re-check loading of dishes in
another
the basket
The revolving arms knock against Again re-check loading
the dishes
Inadequate air flow
Leave the dishwasher door ajar
at the end of the wash program
to allow the dishes to dry naturally
N.B.: Should any of the situations occur and should the machine give a bad wash performance,
it is necessary to remove the deposits from the dishes by hand since the final drying cycle hardens the
deposits which a second wash in the machine would not be able to remove.
If the malfunction continues contact a Service Centre quoting the serial number of the dishwasher.
This is found on the plaque on the inside of the dishwasher door at the top or on the guarantee.
This information will make it possible to take more effective action more quickly.
The manufacturers decline any responsibility for any printing mistakes in this instruction booklet.
They also reserve the right to modify their own appliances as necessary without altering the
essential characteristics.
26
27
The manufacturer declines all responsibility in the event of any printing mistakes in this
booklet. The manufacturer also reserves the right to make appropriate modifications to
its products without changing the essential characteristics.
This appliance is marked according to the European directive 2002/96/EC on Waste Electrical and Electronic
Equipment (WEEE).
By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the
environment and human health, which could otherwise be caused by inappropriate waste handling of this
product.
The symbol on the product indicates that this product may not be treated as household waste. Instead it shall
be handed over to the applicable collection point for the recycling of electrical and electronic equipment
Disposal must be carried out in accordance with local environmental regulations for waste disposal.
For more detailed information about treatment, recovery and recycling of this product, please contact your local
city office, your household waste disposal service or the shop where you purchased the product.
06.03 - 41016461.A - Printed in Italy - Imprimé en Italie
EN
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising