Terzismo | LDFHP8 | Terzismo LDFHP8 User manual

Terzismo LDFHP8 User manual
INSTRUCTION BOOK
LDFHP8
Heat Pump Tumble Dryer
English
2
INDEX
Introduction
Delivery Information
Unpacking the Product
Safety Reminders
Use
Installation
Safety Warnings
The Laundry
Environmental Issues
Customer Service
Installation
Electrical Requirements
Adjusting the Feet
Drain Hose : Fitting Instructions
Preparing the Load
Clothes Preparation
Do Not Tumble Dry
Energy Saving
Sorting the Load
Drying Guide
Controls and Indicators
Selecting the Programme
Door and Filter
Opening the Door
Filter
Filter Care Indicator
Water Container
To Remove the Container
Operation
Delay Start Function
Cancelling and Resetting the Programme
Cleaning and Routine Maintenance
Cleaning the Dryer
Technical Specifications
Troubleshooting
Customer Care
Spares
Gias Service
EN
2
3
3
3
3
3
4
4
5
5
5
6
6
6
7
8
8
8
8
8
8
9
10
11
11
11
11
12
12
12
13
13
13
13
13
14
14
14
14
INTRODUCTION
Please read and follow these instructions carefully and operate the machine accordingly. This
booklet provides important guidelines for safe use, installation, maintenance and some useful
advice for best results when using your machine.
Keep all documentation in a safe place for future reference or for any future owners.
Delivery Information
Please check that the following items are
delivered with the appliance:
● Instruction manual
● Guarantee card
● Energy label
Check that no damage has occurred to the
machine during transit. If it has, call for service
by Customer Care.
Failure to comply with the above can
compromise the safety of the appliance. You
may be charged for a service call if a problem
with your machine is caused by misuse.
UNPACKING THE PRODUCT
Remove the machine from
its packaging close to the
final location of the
machine.
1- Cut carefully around the
base of the packaging and
up one corner.
2- Remove the polythene
sleeve and lift the dryer off
the polystyrene base.
Dispose of the packaging safely. Make
sure it is out of the reach of children,it is a
potential source of danger.
SAFETY REMINDERS
Use
● This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities,or lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a person responsible for their safety.
● Children should be supervised to ensure that they do not play with the appliance.
● WARNING Misuse of a tumble dryer may create a fire hazard.
●This machine is solely for domestic use, i.e. to dry household textiles and garments.
●This machine should only be used for its intended purpose as described in this manual. Ensure
that the instructions for installation and use are fully understood before operating the appliance.
● Do not touch the appliance when hands or feet are damp or wet.
● Do not lean on the door when loading the machine or use the door to lift or move the machine.
●Do not allow children to play with the machine or its controls.
● WARNING Do not use the product if the fluff filter is not in position or is damaged; fluff could be
ignited.
● WARNING Where the hot surface symbol is
located the temperature rise during operation
of the tumble dryer may be in excess of 60 degrees C.
● Remove the plug from the electricity supply. Always remove the plug before cleaning the
appliance.
● Do not continue to use this machine if it appears to be faulty.
● Lint and fluff must not be allowed to collect on the floor around the outside of the machine.
● The drum inside may be very hot. Always allow the dryer to complete the cool down period before
removing the laundry.
EN
3
SAFETY REMINDERS
CAUTION,risk of fire.Read these warnings
carefully to avoid the possible danger fire.
Safety Warnings
● Items that have been spotted or soaked with vegetable or cooking oil constitule a fire hazard and
shoul no be placed in a tumble dryer. Oil-affected items can ignite spontaneously, especially when
exposed to heat sources such as in a tumble dryer.The items become warm, causing an oxidation
reaction in the oil. Oxidation creates heat. If the heat can not escape, the item s can become hot
enough to catch fire. Pilling, stacking or storing oil-affected items can prevent heat from escaping
and so create a fire hazard. If it is unavoidable that fabrics that contain vegetable or cooking oil or
have been contaminated by hair care products be placed in a tumble dryer they should first be
washed in hot water with extra degergent- this will reduce but not eliminate , the hazard. The « cool
down » cycle of the tumble dryers should be used to reduce the temprature of the items. They
should not be removed from the tumble dryer or piled or stacked while hot.
● Items that have been previously clean in, washed in, soaked in or spotted wth petrol/gasoline, dry
cleaning solvents or other flammable or explosive substances should not be placed in a tumble
dryer. Highly flammable substances commonly used in demosetic environments include acetone,
denatured alcohol, perol/gasoline, kerosene, spot removers (some brands), turpentine, waxes
and wax removers.
● Items containing foam rubber ( also known as latex foam) or similarly textured rubber, like
materials should not be dried in a tumble dryer on a heat setting.
● Fabric softeners or similar products should not be used in a tumble dryer to eleminate the effects
of static electricity unless this practce is specifically recommended by the manufacturer of the
fabric softener or product.
● Undergarments that contain metal reinforcements should not be placed in a tumble dryer.
Damage tot he tumble dryer can result if the metal reinforcements come loose during drying. When
available a drying rack could be used for such items.
● Plastic articles such as shower caps or babies waterproof napkin covers should not be placed in
a tumble dryer.
● Rubber-backed articles, closthes fitted with foam rubber pads, pillows, galoshes and rubbercoated tennis shoes should not be placed in a tumble dryer.
Installation
● Check that the product has no visible signs of damage before use. If damaged do not use and
please call Customer Care.
● Do not use adapters, multiple connectors and/or extensions.
● Never install the dryer against curtains and be sure to prevent items from falling or collecting behind
the dryer.
● The appliance must not be installed behind a lockable door, a sliding door or a door with a hinge on
the opposite side to that of the tumble dryer.
EN
4
SAFETY REMINDERS
The Laundry
● Do not dry unwashed items in the tumble
dryer.
● WARNING Do not tumble dry fabrics treated
with dry cleaning fluids.
● WARNING Foam rubber materials can,
under certain circumstances, when heated
become ignited by spontaneous combustion.
Items such as foam rubber (latex foam),
shower caps, waterproof textiles, rubber
backed articles and clothes or pillows fitted
with foam rubber pads MUST NOT be dried in
the tumble dryer.
● Always refer to the laundry care labels for
directions on suitability for drying.
● Clothes should be spin dried or thoroughly
wrung before they are put into the tumble
dryer. Clothes that are dripping wet should not
be put into the dryer.
● Lighters and matches must not be left in
pockets and NEVER use flammable liquids
near the machine.
● Glass fibre curtains should NEVER be put in
this machine. Skin irritation may occur if other
garments are contaminated with the glass
fibres.
● Items that have been soiled with substances
such as cooking oil, acetone, alcohol, petrol,
kerosene, spot removers, turpentine, waxes
and wax removers should be washed in hot
water with an extra amount of detergent before
being dried in the tumble dryer.
● Fabric softeners, or similar products, should
be used as specified by the fabric softener
instructions.
Customer Service
● To ensure the continued safe and efficient
operation of this appliance we recommend
that any servicing or repairs are only carried
out by an authorised service technician.
If the appliance is not running properly or
breaks down, switch it off and disconnect the
plug from the socket. Consult Customer Care
for possible repair.
Environmental Issues
● All packaging materials used are
environmentally-friendly and recyclable.
Please help dispose of the packaging via
environmentally-friendly means. Your local
council will be able to give you details of current
means of disposal.
● To ensure safety when disposing of an old
tumble dryer disconnect the mains plug from
the socket, cut the mains power cable and
destroy this together with the plug. To prevent
children shutting themselves in the machine
break the door hinges or the door lock.
European Directive 2012/19/EU
This appliance is marked according
to the European directive 2012/19/EU
on Waste Electrical and Electronic
Equipment (WEEE).
WEEE contains both polluting substances
(which can cause negative consequences for
the environment) and basic components (which
can be re-used). It is important to have WEEE
subjected to specific treatments, in order to
remove and dispose properly all pollutants, and
recover and recycle all materials.
Individuals can play an important role in
ensuring that WEEE does not become an
environmental issue; it is essential to follow
some basic rules:
- WEEE should not be treated as household
waste.
- WEEE should be handed over to the relevant
collection points managed by the municipality
or by registered companies. In many countries,
for large WEEE, home collection could be
present.
In many countries, when you buy a new
appliance, the old one may be returned to the
retailer who has to collect it free of charge on a
one-to-one basis, as long as the equipment is of
equivalent type and has the same functions as
the supplied equipment.
EN
5
INSTALLATION
Electrical Requirements
Tumble dryers are supplied to operate at a
voltage of 220V-240V, 50 Hz single phase.
Check that the supply circuit is rated to at least
6A.
Electricity can be extremely dangerous.
This appliance must be earthed.
The socket outlet and the plug on the
appliance must be of the same type.
Do not use multiple adapters and/or
extension leads.
The plug should be accessible for
disconnection after the appliance has been
installed.
You may be charged for a service call if a
problem with your machine is caused by
incorrect installation.
VENTILATION
Adequate ventilation must be provided in the
room where the tumble dryer is located to
prevent gases from appliances burning other
fuels, including open fires, being drawn into the
room during operation of the tumble dryer.
● Exhaust air must not be discharged into a
flue which is used for exhausting fumes from
appliances burning gas or other fuels.
● Check regularly that the air flowing through
the dryer is not restricted.
● Check the fluff filter after use, and clean, if
necessary.
●The inlet and outlets should be kept free from
obstructions. To ensure adequate ventilation
the space between the bottom of the machine
and the floor must not be obstructed. There
should be a gap of at least 12mm between the
machine and any obstructions.
● Prevent items from falling or collecting behind
the dryer as these may obstruct the air inlet and
outlet.
● NEVER install the dryer up against curtains.
If the mains cord on this appliance is
damaged, it must be replaced by a special cord
which is ONLY obtainable from the spares
service. It must be installed by a competent
person.
Do not plug the machine in and switch it
on at the mains until the installation is
completed.For your safety, this dryer must be
correctly installed. If there is any doubt about
installation, call GIAS Service for advice.
Air Outlets in the Base
Important: During transport ensure that the
dryer is in an upright position, if it's necessary
you can only flip in the side shown;
Adjusting the Feet
Once the machine is in
place the feet should
be adjusted to ensure
that the machine is
level.
EN
6
Caution: If the product is in different side, wait
at least 4 hours before switching on so that the
oil can flow back into the compressor. Failure to
do this could result in damage to the
compressor.
DRAIN HOSE KIT: FITTING INSTRUCTIONS
To avoid having to empty the water container
after each drying cycle, the water normally
collected during the drying cycle can be
discharged directly to a waste water drain pipe
(the same drainage system as household
sinks).Water Bye-Laws prohibit connection to
a surface water drain. The waste water drain
pipe system should be located adjacent to the
tumble dryer.
The kit is composed: 1 hose, 1 straight
Ÿ
hose connector, 1 pipe clip and 1 plastic tie.
WARNING! Switch off and remove the
tumble dryer plug from the electricity supply
before carrying out any work.
Fit the Kit as Follows:
1.Unscrew and
remove the 3 screws,
at the rear of the
machine, retaining the
worktop trim.
2. Remove the rear
worktop trim and the
worktop surface by
carefully sliding it
towards the rear of the
machine.
3. The waste water
container is situated at
the right-hand side of
the machine (viewed
from the rear). A grey
hose connects to the
bridge above the water
container. Using pliers,
remove the pipe
retaining clip from the
bridge.
4. Pull the hose off the
bridge connection.
5. Attach the hose from
the kit, using the
connector and pipe
clips supplied, to the
hose removed from the
bridge connection.
6. Take off the water
container cover from
the rear of the machine
by removing the two
screws and unclipping
the cover.
7. Break off the tab on
the side of the cover
and replace the cover
on the machine, refit
the screws. You should
now have revealed a
hole in the back of the
cabinet next to the
Cover.
8. Feed the drain hose
through the hole in the
cabinet.
9. Locate the grey pipe
in the cutout of the tray
and secure the pipe
assembly to the bridge
with the plastic tie.
10. Carefully slide the
worktop back into
position ensuring that
the hose is not trapped
and replace the
worktop rear trim with
the 3 screws.
11. Connect the new
drain hose to the waste
water pipe. Make sure
that the new hose does
not kink when pushing
the tumble dryer into
position. Ensure that
the guidelines, as
shown, are followed
when routing the new
external hose.
12. Connect to the
mains electricity
supply.
13. After emptying the
waste water container
switch the machine ON
(and press the 'START'
button on electronic
models) to commence
with the drying
program.
EN
7
PREPARING THE LOAD
Before using the tumble dryer for the first time:
● Please read this instruction book thoroughly.
● Remove all items packed inside drum.
● Wipe the inside of the drum and door with a
damp cloth to remove any dust which may
have settled in transit.
Clothes Preparation
Make sure that the laundry you are going to dry
is suitable for drying in a tumble dryer, as shown
by the care symbols on each item.
Check that all fastenings are closed and that
pockets are empty. Turn the articles inside out.
Place clothes loosely in the drum to make sure
that they don't get tangled.
Do Not Tumble Dry:
Woollens, silk, delicate fabrics, nylon stockings,
delicate embroidery, fabrics with metallic
decorations, garments with PVC or leather
trimmings, training shoes, bulky items such as
sleeping bags, etc.
IMPORTANT: Do not dry articles which
have been treated with a dry cleaning fluid or
rubber clothes (danger of fire or explosion).
During the last 15 minutes (roughly) the
load is always tumbled in cool air
Energy Saving
Only put into the tumble dryer laundry which
has been thoroughly wrung or spin-dried. The
drier the laundry the shorter the drying time thus
saving electricity.
ALWAYS
● Try to dry the maximum weight of laundry, this
will save time and electricity.
● Check that the filter is clean before every
drying cycle.
NEVER
● Exceed the maximum weight, this will waste
time and electricity.
● Put dripping wet items into the tumble dryer,
this may damage the appliance.
EN
8
Maximum Drying Weight
Cottons
Max.
10 Kg
9 Kg
8 Kg
Synthetics
Max.
4 Kg
4 Kg
4 Kg 3,5 Kg 3 Kg
7 Kg 6 Kg
Do not overload the drum, large items
when wet can exceed the maximum admissible
clothes load (for example: sleeping bags,
duvets).
Sort the Load as Follows
● By care symbols
These can be found on the collar or inside seam:
Suitable for tumble drying.
..
Tumble drying at high temperature.
.
Tumble drying at low temperature only.
Do not tumble dry.
If the item does not have a care label it must be
assumed that it is not suitable for tumble drying.
● By amount and thickness
Whenever the load is bigger than the dryer
capacity, separate clothes according to
thickness (e.g. towels from thin underwear).
● By type of fabric
Cottons/linen: Towels, cotton jersey, bed and
table linen.
Synthetics: Blouses, shirts, overalls, etc. made
of polyester or polyamid, as well as for
cotton/synthetic mixes.
● By drying level
Sort into: iron dry, cupboard dry, etc. For delicate
articles press the Acrylic Synthetic button to
select low drying temperature.
CONTROLS AND INDICATORS
Empty Water
Indicator
Filter Care
Indicator
Time Selection
Button
Delay Start
Button
Programme
Selector
Program
Display
Acrylic Synthetic
Button
Anti-Crease
Button
Start/Pause
Button
Control Panel and Indicator Lights
Programme Selector – Select the required programme
Time Selection Button – Allows the user to change duration of the programme selected by
Programme Selector. It can be used only with the selection of: Mix&Dry, Shirts and Time
Programmes
Delay Start Button – Allows the user to delay the start of the drying cycle (see details of
Operation )
Acrylic and Synthetic Button – When pressed the
default indicator will fade and
will be
illuminated
Anti- Crease Button – Allows the user to select a post drying anti-crease cycle.
Start/Pause Button – Press to commence/ to pause the selected drying programme.
Filter Care indicator
– lights when the filter needs cleaning
Empty Water indicator
– lights when the water container is full
Program Display – Related indicator lights when a auto programme has been selected.
- Indicator will come on when the eco programme has been selected.
Refresh
– The indicator lights up when the programme starts the cool down stage.
SELECTING THE PROGRAMME
The Sensor Dry machine gives many options for drying the laundry
to suit all circumstances. The table on the next page lists the
programmes and the function of each programme.
Note:
The sensor may not detect a small load of small articles. For small
loads and separate items or pre-dried fabrics with low moisture
content, use the timed programmes.
If the sensor does not detect the item the dryer will only operate for
10 minutes before going into cooldown.
If the load is too large or too wet to tumble dry the dryer will
automatically go into cooldown after approximately 3 hours.
In these cases we advise to use a time cycles between 30 and
75minutes depending on the load size and dryness required, and
select high or low heat depending upon the fabric type.
EN
9
SELECTING THE PROGRAMME
PROGRAMME
IDEAL FOR
Ultra Dry
Clothes you want completely dryed, e.g. towels, bathrobes, table clothes
or sheet. Time: around 3h.
Store Dry
Clothes you want to fold and store without ironing, e.g. shirts in mixed
fabrics, socks, baby clothes. Time: around 2h and 45 min.
Hang Dry
Clothes you don’t need to iron, but just hang after the drying cycle. Time:
around 2h and 30 min.
Iron Dry
Leave clothes slightly damp to allow easier ironing. Time: around 1h and
50 min.
Refresh
Clothes you just need to refresh. Good for items of clothing which have been
left prior to ironing or if they have been dried outside or on radiators. This
programme has a specific Anti-Crease function that relaxes fibres and
makes easier ironing. Time: 9 min + 3 min cool down.
Wool
Woolen clothes: the program can be used to dry up to 1 kg of laundy (around 3
jumpers). It is recommended to reverse all clothes before drying. Timing can
change due to dimensions and thickness of load and to spinning chosen
during washing. At the end of the cycle, clothes are ready to be worn, but if
they are more heavy, edges can be a bit wet: it is suggested to dry them
naturally. It is recommended to unload clothes at the very end of the cycle.
Attention: felting process of wool is irreversible; please dry exclusively clothes
with symbol (symbol "ok tumble"); this program is not indicated for acrylic
clothes.
Mix & Dry
To dry mixed cotton and synthetic clothes: save time and no need to
separate the washing and dry them in different cycles. Time: around 2h
(max 4 kg).
Shirts
To dry shirts both cotton and synthetic fabrics. Time: 1h for 2kg of synthetic
shirts (around 10 shirts); 1h and 20 min for 3 kg of cotton shirts (around 10
shirts).
Rapid 40’
For dry, refreshed and ready to dress clothes in onyl 40 minutes. Sensor
system keeps under control the temperature to have always the best result.
Max 2 kg.
Time
If you want to choose drying times, from 30 to 180 minutes. By selecting “20
min” you choose a “cool programme”, ideal to refresh clothes and to remove
eventual smells.
Jeans
EN 10
To dry up to 4 kg of Jeans (around 5 pairs). The programme works for around
2h, but timing can change according to the load and washing spin speed.
Jeans programme can only be used for 100% cotton items, please do not
mix colours nor dry jeans with embroideries or accessories.
DOOR and FILTER
Opening the Door
To Clean the Condenser Filter
Pull on handle to open
the door.
To restart the dryer,
close the door and
press Start/Pause
Button.
WARNING! When the tumble dryer is in
use the drum and door may be VERY HOT.
Never stop a tumble dryer before the end of the
drying cycle unless all items are quickly
removed and spread out so that the heat is
dissipated.
Filter
IMPORTANT: To maintain the efficiency of the
dryer check that the fluff filter is clean before
each drying cycle.
Do not operate the dryer without the filters.
Clogged filters can increase the drying time
and cause damage which may result in
expensive repair costs.
1.Pull the filter
upwards.
2. Open filter as shown.
3.Gently remove lint
using a soft brush or
your fingertips.
4.Snap the filter
together and push
back into place.
Filter Care Indicator
Lights when the filter
needs cleaning.
Check and clean the
main filter in the door
and the condenser
filters allocated in the
bottom of the dryer,If
the laundry is not
drying check that the
filter is not clogged.
1.Remove
kickplate.
the
2. Turn the two locking
levers anti-clockwise
and pull out the front
cover.
3. Gently remove the
filter frame and clean
any dust or fluff with a
cloth from the filter. Do
not use water to clean
the filter.
4. Remove the sponge
gently from its place
and then wash the
sponge by holding it
under a running tap
turning it so to remove
any dust or fluff.
5. Refit the front cover
ensuring it is in the
correct way (as
indicated by the arrow)
and pushed firmly into
place. Lock the two
levers by turning them
clockwise.
6. Refit the kickplate.
DO NOT USE WATER TO CLEAN THE FILTER.
EN 11
WATER CONTAINER
The water removed from the laundry during
the drying cycle is collected in a container
inside the door of the dryer. When the
container is full the
indicator on the control
panel will light, and the container MUST be
emptied. However, we recommend that the
container is emptied after each drying cycle.
NOTE: Very little water will collect during the
first few cycles of a new machine as an internal
reservoir is filled first.
To Remove the Container
OPERATION
1. Open the door and load the drum with
laundry. Ensure that garments do not hinder
closure of the door.
2. Gently close the door pushing it slowly until
you hear the door 'click' shut.
3. Turn the Programme Selector dial to select
the required drying programme (see
Programme Guide).
1. Gently pull out the
tray until it is
completely removed.
Support the tray with
both hands. When it is
full the water container
will weigh about 4kg.
4. If drying synthetics, acrylics or delicate items,
press the
button to reduce the heat level.
The indicator will light up when the machine is in
low heat setting. To deselect in the first few
minutes of the programme, press the
button
, after this time reset the machine to change the
setting.
2 . Ti l t t h e w a t e r
container to empty the
water out through the
rear hole.
5. Press the
button. The dryer will start
automatically and the indicator above the
button will be continuously lit.
When emptyslide the
water container back
into position.
PUSH FIRMLY INTO
PLACE.
3. Press
the cycle.
to restart
NOTE: If you have the
option of drainage near
the dryer it is possible
to use the discharge kit
to provide a permanent
drain for the water
collected by the dryer.
This will remove the
need to empty the
water tray. All the
information for
assembly of the kit is
contained in the kit
envelope.
EN 12
6. If the door is opened during the programme to
check the laundry, it is necessary to press
to
recommence drying after the door has been
closed.
7. When the cycle is nearing completion the
machine will enter the cool down phase, the
clothes will be tumbled in cool air allowing the
load to cool down.
8. Following the completion of the cycle the
drum will rotate intermittently to minimize
creasing. This will continue until the machine is
switched OFF or the door is opened.
Do not open the door during the automatic
programs in order to obtain a proper drying.
OPERATION
Delay Start Function
The Delay Start Function allows the user to delay the start of the drying cycle by 1 to 24 hours.
When the function is first selected the display will show a delay of 1 hour, subsequent presses of
the button will increase the delay with 1 hour steps.
To commence the programme press Start/Pause button and the appliance will complete the drying
cycle at the end of this time. The indicator light will flash to indicate that the start delay is in
progress.
Cancelling and Resetting the Programme
To cancel a programme press the Start/Pause button for 3 seconds. In the TIME CONTROL
display 0:00 Light will flash to indicate that it has been reset.
CLEANING AND ROUTINE MAINTENANCE
Cleaning the Dryer
● Clean the filter and empty the water
container after every drying cycle.
● Regularly clean the filters.
● After each period of use, wipe the inside of
the drum and leave the door open for a while to
allow circulation of air to dry it.
● Wipe the outside of the machine and the
door with a soft cloth.
● DO NOT use abrasive pads or cleaning
agents.
● To prevent the door sticking or the build up
of fluff periodically clean the inner door and
gasket with a damp cloth.
Technical Specifications
Drum capacity
Maximum load
Height
Width
Depth
Energy class
115
See energy label
85 cm
60 cm
60 cm
See energy label
Test Specification
Programme
Load
8 kg
Install and use discharge kit to evacuate the
Condensed water.
IMPORTANT Always switch off and remove
the plug from the electricity supply before
cleaning this appliance.
WARNING! The Drum, door and load may
be very hot.
For electrical data refer to the rating label on
the front of the dryer cabinet (with the door open).
EN 13
TROUBLESHOOTING
What Might be the Cause of...
Defects you can remedy yourself
Before calling Customer Care for technical
advice please run through the following
checklist. A charge will be made if the machine
is found to be working or has been installed
incorrectly or used incorrectly.
If the problem persists after completing the
recommended checks, please call Customer
Care, they may be able to assist you over the
telephone.
Time display to end could change during
drying cycle. The time to end is
continuously checked during the drying
cycle and the time is adjusted to give the
best estimation time. The displayed time
may increase or decrease during the cycle
and this is normal.
Drying time is too long/clothes are not dry
enough…
● Have you selected the correct drying
time/programme?
● Were the clothes too wet? Were the clothes
thoroughly wrung or spindried?
● Does the filter need cleaning?
● Is the dryer overloaded?
● Has the
option been selected from a
previous cycle?
The dryer does not operate…
● Is there a working electricity supply to the
dryer? Check using another appliance such as
a table lamp.
● Is the plug properly connected to the mains
supply?
● Is there a power failure?
● Is the door fully closed?
● Is the dryer switched on, both at the mains
supply and at the machine?
● Has the drying time or the programme been
selected?
● Has the machine been switched on again after
opening the door?
EN 14
The dryer is noisy…
● Switch off the dryer and contact Customer Care
for advice.
The
Indicator is on…
● Does the filter need cleaning?
The
Indicator is on…
● Does the water container need emptying?
CUSTOMER CARE
Should there still be a problem with your dryer
after completing all the recommended checks,
please call Customer Care for advice.
They may be able to assist you over the
telephone or arrange for a suitable appointment
for an engineer to call under the terms of your
guarantee. However, a charge may be made if
any of the following applies to your machine:
● Is found to be in working order.
● Has not been installed in accordance with the
installation instructions.
● Has been used incorrectly.
Spares
Always use genuine spares, available direct
from an authorised spare parts centre.
Service
For service and repairs call your local Customer
Care.
The manufacturer declines all responsibility
in the event of any printing mistakes in this
booklet. The manufacturer also reserves the
right to make appropriate modifications to
its products without changing the essential
characteristics.
40009396
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising