Terzismo | BWMI1206.1 | Terzismo BWMI1206.1 Manuale utente

Terzismo BWMI1206.1 Manuale utente
BWMI1206.1 /
BWMI1407.1
Fully integrated
washing machine
USER MANUAL FOR YOUR BAUMATIC
BWMI1206.1
BWMI1407.1
Fully integrated
washing machine
NOTE: This User Instruction Manual contains important
information, including safety & installation points, which will
enable you to get the most out of your appliance. Please keep it
in a safe place so that it is easily available for future reference.
GS 15/10/12
2
Contents
Environmental note
Important safety information
Specifications
Product and aperture dimensions
Product specifications
Control panel
Detergent drawer
4
5-6
7-8
7
7-8
9 - 14
13 - 14
Preparing the wash cycle
Preparing your garments for washing
A selection of wash care symbols
Detergents and conditioners
Program table
Program description
Wash program guidance
Selecting a wash program
Cancelling or pausing a wash program
Delay start feature
Saving energy when using your washing machine
Automatic consumption reduction
Removing stains
Stain removal rules
Stain removal guide
14
14
15
15
17
18
20
21
21
22
22
23
23
23
24
Maintenance and cleaning
In daily use
Control panel and washing machine cabinet
Detergent drawer
The washing machine drum
Door
90 degree maintenance wash
Cleaning the filter
Long periods of not in use
General troubleshooting
Poor wash results
25 - 28
25
25
26
26
26
27
27
28
28 - 29
30
Installation
Unpacking and removing the transit bolts
Positioning and levelling the appliance
Fitting the décor door
Connecting to the mains water supply
Water outlet
Power supply
Before first use maintenance wash
Baumatic consumables
Technical data
Contact details
31
31
32
33
35
36
37
37
39
40
42
- 20
- 15
- 16
- 18
- 20
- 25
- 22
- 23
- 24
- 25
-
38
32
33
35
- 38
- 41
3
Environmental note
Note: Before discarding an old appliance, switch off and
disconnect it from the power supply. Cut off and render any plug
useless. Cut the cable off directly behind the appliance to prevent
misuse. This should be undertaken by a competent person. Disable
the door lock to make sure that children cannot get stuck inside
the appliance.
4
Important safety information
Your safety is of the utmost importance to Baumatic.
Please make sure that you read this instruction booklet
before attempting to install or use the appliance. If you
are unsure of any of the information contained in this
booklet, please contact the Baumatic Advice Line.
General Safety
o Repairs to your appliance must only be carried out by a
Baumatic engineer or one of its authorised service agents. Any
attempt by an inexperienced person to repair the appliance,
could result in injury or damage to your washing machine.
o If you notice that the mains cable is damaged. The appliance
must not be used. The same applies if you notice that the
worktop, control panel or base area is damaged. As this could
allow access to the internal components of the machine.
o The appliance should be switched off and isolated from the
mains supply, before either cleaning or maintenance work is
attempted.
o The mains cable must not be used to pull the plug out of the
electrical socket.
o The machine should not be sprayed with water.
o The glass of the porthole door may become hot during the higher
temperature wash programs.
o The machine should be allowed to cool before carrying out an
emergency drain or cleaning the drain filter.
o It is possible for small animals to chew either mains cables or
water hoses, which could cause an electric shock hazard.
Installation
o The installation instructions contained within this user manual
should be followed.
o It is obligatory for the completed installation to comply with all
relevant building regulations and local water authority
requirements.
5
o Before the first use of the appliance, we advise that a
90°C cotton wash is completed. No garments should be
placed inside the machine; however a small amount of
detergent must be used.
During Use
o It is recommended that the appliance is unplugged and the
water supply is switched off after the machine is used.
o This appliance is only designed to wash normal domestic
washloads. If you use your washing machine in any other way or
it is incorrectly used, then Baumatic accepts no liability for any
damage that might be caused and any guarantee will be void.
o No attempt should be made to alter or modify the specifications
of this appliance.
o The detergents that you place in this appliance should be
suitable for automatic washing machines. With regards to dosage
levels, the detergent manufacturer’s recommendations should be
followed.
o You should not wash garments that have been in contact with
flammable materials.
o Your washing machine should not be used for dry cleaning.
o If you use either dyes or bleaching agents inside this machine,
then you should consult with the manufacturer of these products
to make sure they are suitable for use in your washing machine.
Baumatic cannot be held responsible for any damage that may
result.
Child Safety
o Your washing machine should only be used by adults. You should
not allow children in the area of the machine unsupervised. You
should not let them touch the controls or play with the appliance.
o It could be possible for a child or pet to gain access to the
washing machine through the porthole door. Therefore please
check the drum before using the appliance.
o Any packaging that is removed from the machine should be kept
away from children.
o All detergents should be kept out of children’s reach in a safe
place.
6
Specifications
Product dimensions:
Height:
Width:
Depth:
Aperture dimensions:
820 mm
596 mm
541 mm
825 mm
600 mm
570 mm
Product specifications
BWMI1206.1
o Load capacity:
6 kg
o Maximum spin speed: 1200 rpm
o Drum size:
46 litres
o
o
o
o
o
o
o
o
o
BWMI1407.1
7 kg
1400 rpm
56 litres
15 wash programs
3 option buttons: Easy Iron, Extra Rinse and Cold Wash
Variable spin speed with no spin option
Porthole diameter: 30 mm
180° door opening
LED display
Digital countdown indicator
Delay start
Automatic consumption reduction
7
o
o
o
o
o
o
o
Self-adjusting water level to load
Imbalance control system
Overflow protection
Foam protection
Safety lock
Fuzzy logic
Adjustable feet
Energy efficiency:
Energy rating
Wash performance
Water extraction performance class
A+
A
B (BWMI1206.1)
A (BWMI1407.1)
8
Control panel
A)
B)
C)
D)
E)
F)
G)
H)
I)
J)
K)
L)
M)
Door open button
Door lock indicator light
Start/Pause button
Delay start button
Easy iron button
Extra rinse button
Cold wash button
Spin speed button
Spin speed indicator
Remaining time indicator
Program selection dial
Cycle option indicators
Detergent drawer
Door open button
Press this button to open the porthole door. A
safety device prevents the door from being
opened immediately after the end of the cycle.
You should wait for 2 minutes after the wash
cycle has finished and the door lock indicator
light has gone out before opening the door.
Door lock indicator light
The door lock indicator will light when the door is fully
closed and the machine is switched on. When the
Start/Pause button is pressed to start a wash cycle,
the indicator will flash for a few seconds and then light. If the door
is not closed the indicator will continue to flash. The door
cannot be opened until the door lock indicator has gone out.
9
Start/Pause button
This button should be used to start the chosen wash
program. When the button is pressed, the appliance
will begin the cycle within a few seconds. You can also
press this button to pause a wash cycle in progress
and continue after. When a program is selected,
wait for the STOP light to flash before pressing
the Start / Pause button.
Delay start button
This button can be used to program a delay start of 3, 6
or 9 hours. See the section “Delay start feature” on page
22 for instructions.
Easy iron button
Use this button to select the easy iron function. This will
minimise creases in mixed fabrics, delicate fabrics and
woollens and silk. It works in the following ways:
Fabric
(according to
program
selected)
Mixed fabrics
Delicate fabrics
Woollens / silk
Process
The water is gradually cooled throughout the final
2 rinses with no spinning and then a delicate spin
assures the maximum relaxation of the fabrics.
The final 2 rinses are carried out with no spinning
and then the fabrics are left in water until it is
time to unload. When you are ready to unload,
press the easy iron button to drain.
After the final rinse the fabrics are left in water
until it is time to unload. When you are ready to
unload, press the easy iron button to drain and
spin.
10
Extra rinse button
This button will program the machine to add an
additional rinse to the cycle. This function is ideal for
people with sensitive skin as it removes more of the
detergent from washing. It is advisable to use this
function for very dirty loads where extra detergent has
been used. This option can be used only on some
programs.
Cold wash button
This button allows you to change every program into a
cold washing cycle without altering other characteristics
of the cycle such as water level, time and features.
Spin speed button
The spin cycle is important to remove as much water as
possible from the laundry without damaging the fabrics.
You can adjust the spin speed of the machine to reduce
the maximum speed, by pressing the spin speed button.
The machine is fitted with an imbalance control system
to cancel the spin cycle if the load is unbalanced. This
reduces the noise and vibration in the machine and so
prolongs the life of your appliance.
You can select this symbol to choose “No Spin”.
Spin speed indicator
When you choose a wash program, the maximum
possible spin speed will be automatically selected and
shown by the relevant indicator light turning on. By
pressing the spin speed button you can choose a lower
spin speed.
11
Remaining time indicator
This display shows the time remaining for a set
wash program. The icons indicate the following
remaining times:
90 light:
60 light:
30 light:
15 light:
Stop light:
Remaining time above 60 minutes
Remaining time less than 60 minutes
Remaining time less than 30 minutes
Remaining time less than 15 minutes
End of the program.
The display also shows the set delayed start time of 3, 6 or 9 hours.
The stop light will flash while a program is being set until the
program has started or the program selection knob is returned to
the “OFF” position.
Program selection dial
This control knob allows
you to select the wash
program of your choice.
You can rotate the knob in
both directions.
Cycle option indicators
The relevant indicator light will turn on to
show which option has been selected for the
program. If you select an option that is not
compatible with the chosen program, the indicator light will not turn
on.
12
Detergent drawer
Pre wash section
This compartment should have detergent placed in it, if you are going
to select a wash program that has a pre wash as part of it.
Main wash section
This compartment should have detergent placed in it (you should also
put a water softening agent in this section, if you use one). The
detergent will be added to the drum at the start of the main wash
program.
Conditioner section
This compartment should be used for liquid conditioners (fabric
softener, starch). They will be added to the wash load during the final
rinse.
IMPORTANT: Only liquid products should be used in the
conditioner compartment. The machine is programmed to
automatically take up additives during the final rinse stage for
all wash cycles.
o If liquid detergents are used,
insert the special container
supplied into the compartment
labelled “II”.
o This ensures that the liquid
detergent enters the drum at
13
the right stage of the wash cycle.
o Some detergents are difficult to utilise so
an in drum dispenser should be used if
recommended
by
the
detergent
manufacturer.
Preparing the wash cycle
Preparing your garments for washing
o Your washing should be sorted out, according to
the fabric type and the wash care symbol that is
printed on the garment’s wash care label. (See
separate section on wash care symbols).
o Your washing should also be sorted out
according to the degree of soiling.
o Check all pockets on a garment to make sure
that they are empty.
o Remove any detachable metal items (badges,
paperclips, safety pins etc).
o Zips should be closed, duvet covers and pillow cases should be
buttoned up and any loose straps should be tied up. This will
help to prevent other garments from getting damaged during the
wash.
o Woollens and knitted coloured fabrics should be turned inside out
before being washed in the appliance.
o Small delicate items (tights, baby socks) should be placed in
either a washing net or a zipped pillow case.
o Curtains should be handled with particular care. All plastic hooks
or metal strips must be removed before being washed in the
appliance.
o Coloured items and whites should be washed
in separate wash cycles.
14
o New garments often contain an excess of dye, therefore it is
advisable to wash them separately for their first wash.
o Garments should be unfolded and shook out before being placed
inside the machine.
A selection of wash care symbols
Washing
Boiling
temp
95°C
Normal
temp
60°C
Normal
temp
40°C
Do not
wash!
Bleachable
in cold
water
Do not
bleach!
Wool
seal
Delicate
temp
30°C
Delicate
temp
40°C
Hand
wash
only
All
solvents
All but TRI
Benzine
only
Do not
clean!
Normal
Low
High
Hang to
dry
Drip dry
Dry
flat
110°C
150°C
200°C
Dry
cleaning
Spin
dryer
Do not
dry!
Ironing
Do not
iron!
o The wash care symbols should be used to help you to select the
most suitable wash program. They will also help you to sort your
laundry into different loads, depending on the fabric type and the
highest temperature which the garment can be washed at.
o If the wash care label does not appear in the above table, then
please refer to the washing machine program chart. This gives
more detailed descriptions of the types of fabric that are suitable
to be washed using a particular wash program.
Detergents and conditioners
IMPORTANT: Only detergents suitable for use in washing
machines should be used.
The amount of detergent that you need to use in your appliance, will
depend on
o The degree of soiling. Lightly soiled garments in general
require less detergent.
15
o The size of the wash load. A smaller wash load will require a
reduction in the amount of detergent.
o The hardness of your tap water. The harder your water is,
then the more detergent you will need to use. The detergent
manufacturers normally give guidance as to how much extra
detergent should be used, depending on the hardness of the
water.
Liquid detergent
If you are using liquid detergent, then in the majority of cases the
liquid should be placed inside the dosing device supplied by the
detergent manufacturer. All instructions on the detergent packaging
should be followed.
Low temperatures
o The enzymes in biological washing detergents work best at low
temperatures to provide excellent cleaning and stain removal
results, but not as low as 20°C.
o Liquid or gel detergents are particularly suitable for low
temperature washing as they dissolve easier and quicker than
powders or tablets.
Water softening agents
If your tap water is hard, then it may be prudent to utilise a water
softening agent. This will help to ensure that the appliance does not
become clogged with hard water deposits. You may also find that it will
allow you to lessen the amount of detergent that you are using.
When using any detergent or water softening
agent, the recommendations of the
manufacturers should be followed.
16
Program table
Program
Resistant
fabrics
(cotton,
linen)
Cotton,
mixed
Laundry
Whites
with
prewash
Fast
coloureds
Fast
coloureds
Non-fast
coloureds
Mixed
fabrics and
synthetics
(mixed,
resistant)
Synthetics
(nylon,
perlon,
mixed
cotton)
Fast
coloureds
with prewash
Fast
coloureds
Non-fast
coloureds
Control
knob
position
MAX
weight
(kg)
90°C +
Pre
7
BWMI1407.
1
60°C
40°C
30°C
60°C
50°C
40°C
6
BWMI1206.
1
7
BWMI1407.
1
6
BWMI1206.
1
7
BWMI1407.
1
6
BWMI1206.
1
7
BWMI1407.
1
6
BWMI1206.
1
3.5
BWMI1407.
1
3
BWMI1206.
1
3.5
BWMI1407.
1
3
BWMI1206.
1
3.5
BWMI1407.
1
3
BWMI1206.
1
Default
Operation
Time
(Mins)
200
Temperat
ure
(°C)*
Detergent
drawer
Up to 90
Yes
Yes
Yes
Up to 60
Yes
Yes
No
Up to 40
Yes
Yes
No
Up to 30
Yes
Yes
No
Up to 60
Yes
Yes
No
Up to 50
Yes
Yes
No
Up to 40
Yes
Yes
No
200
165
180
170
170
115
115
100
100
95
95
95
95
17
Very
delicate
fabrics
Delicates
Machine
washable
woollens
40°C
40°C
2
1.5
BWMI1407.
1
1
BWMI1206.
1
1
Handwash
60
Up to 40
Up to 40
Yes
Yes
Yes
Yes
No
No
50
Up to 30
Yes
Yes
No
60
60
30°C
Specials
Rinse
-
25
-
No
Yes
No
Fast spin
-
9
-
No
No
No
Drain
-
4
-
No
No
No
7
BWMI1407.
1
108
Up to 40
Yes
Yes
No
Up to 30
Yes
Yes
No
“Chef”
Mix
and
wash
system
program
Rapid 30
minute
6
BWMI1206.
1
2
108
30
* The actual water temperature may differ from the declared cycle
temperature.
Program description
o The cotton program is designed for maximum washing and
rinsing efficiency. With spin cycles in between, the program
guarantees the laundry is rinsed thoroughly. The final spin cycle
ensures laundry is spun dry as much as possible up to the
maximum speed.
o The 90°C+Pre cotton program automatically includes a prewash.
o The main wash and rinse gives the best results due to the
rotation rhythms of the drum and the water levels.
o A gentle spin ensures the fabrics become less creased.
18
o This cycle alternates washing and soaking and is recommended
for very delicate fabrics.
o The wash cycle and rinses are carried out with high water levels
to ensure best results.
o This cycle enables you to thoroughly wash woollen garments
without damaging them.
o The cycle consists of alternate periods of activity and pauses.
o This program allows a complete washing cycle for garments
specified as “Hand-wash only” and laundry items made from silk
on the fabric label.
o This cycle has a maximum temperature of 30°C and concludes
with 3 final rinses and a slow spin.
o This program carries out 3 rinses with an intermediate spin
which can be reduced or excluded using the spin speed button.
o The cycle can be used for rinsing any type of fabric or after
hand-washing. This program can also be used as a bleaching
cycle.
o The spin program carries out a maximum spin which can be
reduced using the spin speed button.
o This program drains out the water.
19
o This program enables you to wash together different types of
fabrics e.g. cotton and synthetic fast coloureds.
o The cycle washes with considerable energy saving by using a
temperature of 40°C and alternating spin action with soaking
phases.
o IMPORTANT: The first washing of new coloured fabrics
must be done separately. You should NEVER mix non-fast
coloured fabrics.
o The 30 minute rapid program allows a complete washing cycle to
be carried out in approximately 30 minutes with a temperature
of 30°C.
o When using this cycle it is recommended to use only 20% of the
recommended quantities shown on the detergent manufacturer’s
instructions.
Wash program guidance
o The washing machine automatically selects a spin speed for a
particular wash program. However it is possible to reduce the spin
speed by using the spin speed button.
o Important: You should make sure that the selected spin speed is
appropriate for the garments that you are washing.
o If you use the spin reduction feature, you can make the machine
not go into a spin cycle. If you pick this option, then the machine
will stop with water in the drum.
o Important: Before opening the door of the appliance, you MUST
select the drain program to clear this water.
o The remaining time display shows
for the selected wash cycle. Please
machine, e.g. the temperature of
pressure etc. can affect the time
complete.
an approximate time remaining
note that factors external to the
your water supply, your water
it takes for the wash cycle to
20
Selecting a wash program
o Load your laundry and put detergent
compartment of the soap drawer.
in
the
relevant
o Close the porthole door firmly.
o Select the most appropriate wash program for the garments that
you are washing, by turning the program selection knob.
o Select any program options by using the easy iron button, extra
rinse button or cold wash button.
o Any program option that you select, will affect the length of time
that the wash cycle will take to complete.
o Alter the spin speed, if required, using the spin speed
button.
o Press the Start / Pause button.
o After approximately 5 seconds, you will hear your washing
machine start the wash cycle.
o If there is a power failure or the plug is pulled out of the
socket when a wash cycle is in progress, once power has
been restored, the wash program will continue.
o Whilst the wash program is in progress, the time remaining to
the end of the wash cycle will appear on the display.
Cancelling or pausing a wash program
o To stop a wash program once a wash cycle is in progress,
you should press and hold the Start / Pause button for
about 2 seconds.
o To cancel the program, turn the program selection knob to the
OFF position.
o If you wish to add or remove items the door will remain locked
for two minutes before it is possible to open the door.
o Close the door and press the Start / Pause button to continue
the wash cycle.
21
Before opening the porthole door, you MUST
drain the appliance; otherwise there may still
be water in the drum when you open the door.
Delay start feature
Your appliance has a delay start feature, which allows you to pause
the start of a wash cycle until a later time. You can delay the start
time by 3, 6 or 9 hours.
o Follow the process listed under “Selecting a wash program”.
o Before pressing the Start / Pause button, you should
select the length of time that you want to delay the wash
program for by pressing the delay start button. The
relevant LED will light on the display to show the set delay time.
o Press the Start / Pause button to begin the delay countdown.
The indicator light for the chosen delay time will stop blinking
and remain on.
o At the end of the required delay time, the chosen program will
begin.
o To cancel a time delay that has been set, you should press and
hold the delay start button until the indicator light goes OFF and
the stop light blinks.
o You can then start the program manually by pressing the Start /
Pause button or switch the appliance off by turning the program
selection knob to the OFF position.
Saving energy when using your washing machine
o To prevent any possible waste of energy, water or detergent, we
recommend that you put a full load in your washing machine but
without exceeding the recommended maximum load size. Up to
50% of energy saving can be made with one full load compared
to two half load washes.
o Only use the pre-wash function with particularly dirty loads.
Energy savings of 5% to 15% can be made by not selecting the
pre-wash option for normal soiled laundry.
o Using stain removers before machine washing reduces the need
to wash at temperatures over 60°C. Energy savings of up to
50% can be made by using a 60°C wash temperature rather
than 90°C.
22
Automatic consumption reduction
o The washing machine is fitted with an automatic consumption
reduction system which enables the machine to use the amount
of water needed to wash and rinse the laundry in relation to the
particular load size.
o This results in a reduction in the amount of water used and
electricity needed to heat it to the minimum temperature
required without compromising the washing and rinsing
performance in any way.
o The amount of water and electricity used will always be
appropriate for the amount of laundry which ensures you achieve
excellent washing results whilst respecting the environment and
saving money.
Removing stains
Garments that are covered in stains, grease or are heavily soiled may
need to be pre-washed or soaked before being placed inside of the
washing machine.
o Soaking helps to remove protein-type stains, like blood, milk or
grass.
o Pre-washing helps to loosen soil before the main wash.
Stain removal rules
o Use warm water for soaking or pre-washing stained laundry. Hot
water can set stains.
o Most stains are easier to remove when they are fresh.
o Before treating any stain try to establish; what kind of stain it is,
how old the stain is, what the fabric type is and whether the
fabric is colourfast (check the care label to find this out).
o Washing and drying can fix some stains.
o When bleach is recommended, use a mild fabric bleach that is
safe for the fabric.
o If you need to use a stain remover, put the stained area face
down on a paper towel or white cloth. Apply the stain remover to
the back of the stain. This forces the stain off the fabric, instead
of through it.
23
Stain removal guide
Stain
Alcoholic
beverages
Shoe polish
Tea and
coffee
Chocolate
and cocoa
Tomato
paste
Removal Method
The stain should be first washed with cold water, then
wiped with glycerine and water and rinsed with water
mixed with vinegar.
The stain should be softly scratched without ruining the
material, then rubbed with detergent and rinsed. In case
it is not eliminated, rub with 1 unit of pure alcohol (96
degrees) mixed in 2 units of water and then washed with
lukewarm water.
Stretch the stained area of material on the top of a
container and pour water as hot as the material can
endure on it. If the type of material is suitable, wash it
with lye.
Leave your clothes in cold water and rub with soap or
detergent, wash it in the highest temperature that the
material type can endure. If there is still a stain of oil left,
wipe with oxygenated water (in proportion of 3%).
Scrape the dried pieces without ruining the material, then
leave in cold water for about 30 minutes and wash by
rubbing with detergent.
Meat broth/
egg
Eliminate the dried stain residues and wipe with a sponge
or soft cloth wetted in cold water. Rub with detergent and
wash with diluted lye.
Grease and
oil stains
First wipe the residues. Rub the stain with detergent and
then wash with lukewarm soapy water.
Mustard
First apply glycerine to the stained area. Rub with
detergent and then wash. If the stain still does not
disappear, wipe with alcohol (on synthetic and coloured
cloth, a mixture of 1 unit alcohol, 2 units water should be
used).
Lay your clothes in cold water for 30 minutes. If the stain
still does not disappear, lay in mixture of water and
ammonia (3 table-spoons of ammonia in 4 litres of water)
for 30 minutes.
Lay your clothes in cold water and rub the stained area
with detergent. If the stain has still not disappeared,
apply lye on the fabric of your clothes in proper
proportion. (Do not use lye on coloured clothes).
Mould stains should be cleaned as soon as possible. The
stain should be washed with detergent, and if it does not
disappear, it should be wiped with oxygenated water (in
proportion of 3%).
Hold the stained area under cold water and wait until the
inky water completely runs off. Then rub with water
diluted with lemon juice and detergent. Wait five minutes
and then wash.
Stretch the stained area of your clothes on the top part of
a container and pour cold water on it. Do not pour hot
water on the stain. Wipe with cold water and apply
glycerine. Wait for 1-2 hours and rinse after wiping with a
few drops of white vinegar.
Blood stain
Cream, icecream and
milk
Mould
Ink
Fruit
24
Grass stain
Oil paint
Burnt stain
Rub the stained part with detergent. If the type of fabric
is suitable for use of lye, wash it with lye. Rub your
woollen clothes with alcohol (for coloured one, a mixture
of 1 unit pure alcohol and 2 units of water).
The stain should be eliminated before it dries by applying
thinner on it. Then it should be rubbed with detergent and
washed.
If your fabric is suitable for the use of lye, you can add
lye into your washing water. For woollen fabrics, a cloth
dampened in oxygenated water should be pressed on the
stain and it should be ironed with a dry cloth on it. It
should be washed after rinsing well.
Maintenance and cleaning
In daily use
o Once a wash cycle has completed, you should pull out the
detergent drawer slightly, so it can dry out.
o Leave the porthole door ajar for a short while after a wash cycle
has completed. This should help to prevent stagnant smells and
to protect the door seal.
o Close the water tap.
o We suggest that you disconnect the appliance from your mains
supply, when it is not in use.
Control panel and washing machine cabinet.
IMPORTANT: Do not use any abrasive cleaner or household polish on
either the control panel or operating parts.
o Wipe over the control panel and the external surface of the
machine using a brand new damp cloth with warm water.
o If you ever spill any liquid detergent or conditioner from the
detergent drawer onto the washing machine cabinet, then these
should be cleaned up immediately as they could be corrosive.
25
Detergent drawer
Occasionally the detergent drawer should be cleaned.
o Pull the detergent drawer out as far as it will go and then
remove the drawer by pulling firmly.
o Use warm water and a brush to thoroughly clean the three
compartments of the detergent drawer.
o Clean the area that the detergent drawer slides into with a
brush.
o Replace the detergent drawer by placing it back into the slot.
Then push the drawer fully back into position.
The washing machine drum
The drum of your washing machine is constructed from stainless steel.
However if there are objects that can rust placed inside the drum, then
it is possible for the drum to become stained.
IMPORTANT: Do not use a descaling agent, iron/steel wool or
scouring agents to clean the drum of your appliance.
o Remove any rust stains on the drum with an appropriate
stainless steel cleaning agent.
Door
o You should regularly check to see if any deposits have formed,
or there are any foreign bodies in the rubber door gasket. This
sits inside the opening of the porthole door.
o Regularly clean the door glass with a damp cloth. A build up of
soiling and residues from the water can result in water leaking
from the door.
26
90 degree maintenance wash
The warm and damp environment of a washing machine can lead to a
bacteria build up inside of the machine and in extreme cases you may
even get a “sludge” like material building. To prevent this from
happening, you should do the following:o Leave the door ajar for a few minutes after the wash cycle has
completed.
o Once a month, set your appliance on a 90 degree wash.
o You should not put clothing inside the appliance for this
maintainence wash.
o You should use a wash powder that contains a bleaching agent
(i.e. not a wash powder that is only suitable for washing
coloured garments).
Cleaning the filter
o The washing machine is fitted with a
special filter for catching large
deposits which could block the
discharge hose such as coins, buttons
etc… so they can be easily retrieved.
o Before removing the filter, place a
towel below the filter cap to collect
the small amount of water likely to be
inside the pump.
o Turn the filter anti-clockwise until it
stops in the vertical position. Remove
and clean the filter.
o After cleaning, replace it by turning
the notch on the end of the filter
clockwise.
27
Long periods of not in use
o If the appliance is being
transported or is out of use for
long periods in unheated places,
all remaining water must be
completely removed from the
hoses.
o Ensure the mains power is off
and then unclip the hose and
point it downwards into a basin
until all the water has emptied
out.
General troubleshooting
If your appliance does not appear to be functioning correctly, please
refer to the table below before calling the Customer Care Helpline.
Problem
Machine does not work on
any program.
Does not fill with water.
Cause
Plug not in the socket
Not switched on
Power failure
Fuse blown
Door open
As above
Tap turned off
Program selection knob
not positioned correctly
4) Fill hoses are kinked
1)
2)
3)
4)
5)
1)
2)
3)
Water does not drain away.
1) Kink in discharge hose
2) House drain is blocked
Water on floor around the
washing machine.
1) Leaking gasket between
tap and water inlet hose
2) House drain is blocked
3) Detergent drawer
blocked with soap
residues
1) Water has not yet
Does not spin.
1)
2)
3)
4)
5)
1)
2)
3)
4)
1)
2)
1)
2)
3)
1)
Solution
Plug it in
Switch it on
Check
Check
Close door
Check
Turn on the tap
Position the
program selection
knob correctly
Straighten fill hoses
Straighten
discharge hose
Clean drain
Replace gasket
and tighten hose
and tap well
Clean drain
Clean detergent
drawer
Wait a few minutes
28
drained away.
2) No Spin option selected
Machine vibrates a lot
during the spin.
Door will not open.
The machine makes a
different noise when
spinning.
Only a small level of water
can be seen in the drum.
1)
Washing machine not
completely level
2)
Transit bolts not
removed yet
3)
Load not distributed
evenly
1) 2 minutes have not elapsed
since the program finished
This is due to the brush motor
which ensures better
performance.
Water level automatically set
according to the load size so
may seem less than usual.
2) Choose a spin
speed using the
spin speed control
knob (H)
1) Alter the adjustable
feet
2) Remove the transit
bolts
3) Rearrange the
laundry evenly
1) Wait 2 minutes
N/A
N/A
IMPORTANT: Your appliance has an unbalance control system.
If this system detects that the washload is unevenly distributed
inside the drum. Your washing machine will try to redistribute
the load before spinning. If after several attempts it is unable
to redistribute the washload, then the appliance will either spin
at a slower speed or skip the spin cycle and drain.
Uneven load distribution can be caused by too large a wash
load or too small a wash load. It can also occur if a single item
is washed inside the appliance.
IF
AN
ENGINEER
ATTENDS
DURING
THE
GUARANTEE PERIOD AND FINDS THAT A FAULT
HAS BEEN CAUSED BY AN ITEM IN THE ABOVE
TABLE, WHICH COULD HAVE BEEN CLEARED BY THE
CUSTOMER, THEN YOU MAY BE LIABLE FOR THE
COST OF THE SERVICE CALL.
29
Poor wash results
My garments are looking grey and there are limescale
deposits present in the drum of my washing machine.
o
o
o
o
There is not enough detergent being added.
The incorrect detergent is being used.
Stains are not being pre-treated.
The correct wash program or wash temperature was not
selected.
I have followed the advice given above, but my
garments are still coming out with grey stains on them.
o The garments are soiled with oils, ointments or grease
and were washed without enough detergent.
o The wash temperature selected was too low.
o Fabric conditioner has come into contact with the
garments. If this happens try to wash out these stains
as quickly as you can and try to avoid getting
conditioner on the garments in the future.
After the final rinse, I can still see foam.
o Modern detergents can result in there still being foam in
the final rinse. This does not mean that the washing is
not being rinsed properly.
There is white residue on my garments when I remove
them from the appliance.
o Modern detergents can contain insoluble contents, and
white residue after a wash cycle is not necessarily a
sign of the garments not being rinsed properly.
o You should shake out the garment or brush it off. In
future possibly turn the garment inside out before it is
washed. You may wish to move from a powder
detergent and switch to a liquid detergent instead.
30
Installation
IMPORTANT:
THIS
INSTALLATION
MUST
BE
COMPLETED BY A SUITABLY QUALIFIED PERSON.
BAUMATIC ONLY SANCTION THE INSTALLATION
GIVEN IN THIS INSTRUCTION MANUAL. YOU
SHOULD KEEP THE TRANSIT PACKAGING, IN CASE
YOU NEED TO TRANSPORT THE MACHINE IN THE
FUTURE.
Unpacking the machine and removing the transit bolts
o Remove the polystyrene base
and place the machine near
its permanent position (1).
o Carefully cut through the
hose retaining clip at the
rear of the appliance, taking
care not to cut the hose
(2).
o Remove the 4 fixing
screws A and remove the
spacers B (3).
o It is possible for the
spacers to fall inside the
machine so you should
gentle tilt the appliance to
remove these.
o Cover the 4 holes using the
caps provided (4).
o We recommend that you
keep the transit bolts to
immobilise the machine for
future transit.
31
IMPORTANT: The transit bolts MUST be removed before your
washing machine is used for the first time.
o Apply the insulation sheet or corrugated material to the base of
the appliance as shown above.
o Peel back the sealing strips (1) and line the insulation sheet up
with the base of the appliance (2). Secure the sheet in place
using the screws as shown (3).
Positioning and levelling the appliance
32
o The washing machine requires an aperture of the size given in
the diagram on the previous page.
o Place the washing machine on a solid and level floor surface.
o DO NOT PLACE THE WASHING MACHINE ON A CARPET.
o The feet are adjustable to ensure that the appliance is level. This
is essential for quiet operation.
o Slacken off the lock nut on each
of the washing machine feet
using a spanner.
o Adjust the feet to level off the
washing machine.
o Once levelled correctly, you should tighten the lock nut back up
on each of the washing machine feet using a spanner.
IMPORTANT: When the washing machine is positioned in the location
where it will be used. Make sure that all four feet are resting firmly on
the floor, by pressing down on each corner and checking that the
appliance stands still.
Fitting the décor door
o The front of the appliance has been drilled to accommodate the
hinges to enable the door to be opened from the left or right
hand side.
o The following instructions demonstrate how to fit a standard
height décor door with dummy drawer.
o You will need these
screws to complete
the fitting.
33
o Screw the hinges onto the décor door (A) then fasten the
dummy drawer front to the top edge of the door. Ensure that the
gap between the door and drawer front matches the units on
either side.
o Fasten the magnetic catch (B) using screw (C) to the décor
door.
o Fasten the magnetic catch striker plate (D) to the front of the
appliance, placing the rubber washer (E) under the plate and
screw in place with screws (G).
o Snap mount the plastic cover cap (H) into the lower hinge
position.
34
o Mount the door and hinges to the front of the appliance using
screws (L).
o IMPORTANT: It is recommended that, where possible, the
décor door is hinged on the same side as the appliance
door as this will give greater space to load and unload the
washing.
Connecting to the mains water supply
o Connect and fully tighten the inlet hose to the threaded inlet
valve that is located at the rear of the washing machine. You
should connect the end with the right angle connector on it to
the back of your appliance.
o Connect the other end of the inlet hose to
your mains water supply. This machine only
uses cold water therefore only one hose is
needed to connect to the cold water supply.
DO NOT CONNECT TO A HOT WATER
SUPPLY.
o Tighten the inlet hose to your mains supply
fully.
o Test for any leaks.
35
Water outlet
o Secure the drain hose, so that it cannot move whilst the washing
machine is in use.
o Place the end of the drain hose on your drain pipe. Push it a
short way down into your drain pipe.
o IMPORTANT: Do not insert the drain hose too deeply into the
water pipe, as this may cause siphoning.
o NEVER EXTEND THE DRAINAGE HOSE FROM ITS ORIGINAL
LENGTH.
o For the washing machine to function properly, the end of the
discharge hose must be at a minimum of 50 cm and a maximum
of 85 cm from the ground.
36
Power supply
o IMPORTANT: As your appliance is a built in product, the
electrical socket must still be accessible once the
appliance is installed.
o Consult the rating plate, located on the inner rim of the porthole
door of the appliance BEFORE making the electrical connections.
Ensure that the voltage reaching the plug is the same as that on
the rating plate.
o DO NOT REMOVE THE RATING
INFORMATION ON IT IS IMPORTANT.
PLATE
AS
THE
o The moulded plug that is supplied with the appliance must be
placed into an earthed and insulated socket.
o Broken or damaged power leads must only be replaced by a
suitably qualified person. A power lead of a similar type must be
used in replacement.
o Power lead type – H 0 V V – F 3G 1,5.
o IMPORTANT: We do not recommend that this appliance is
connected to an extension lead.
Before first use maintenance wash
o When your washing machine has been correctly installed, we
recommend that you perform a maintenance wash cycle.
o This will check that all aspects of the installation are correct; it
will also remove any deposits that may have been left in the
drum by the manufacturing process.
o Select the Cotton 90°C wash program.
37
o A small quantity of detergent should be used during this
maintenance wash.
IMPORTANT: If your appliance appears not to be
operating correctly, then you should disconnect it
from your mains supply and then contact
Baumatic Customer Care on telephone number
(0118) 933 6911.
DO NOT ATTEMPT TO REPAIR THE APPLIANCE
YOURSELF.
Please note that if an engineer is asked to attend whilst the product is
under guarantee and finds that the problem is not the result of an
appliance fault, then you may be liable for the cost of the call out
charge.
The appliance must be accessible for the engineer to perform
any necessary repair. If your appliance is installed in such a
way that an engineer is concerned that damage will be caused
to the appliance or your kitchen, then he will not complete a
repair.
This includes situations where appliances have been tiled in,
sealed in with sealant, have wooden obstructions placed in
front of the appliance, like plinths. Or any installation other
than the one specified by Baumatic Ltd. has been completed.
Please refer to the conditions of guarantee that appear on the
warranty card that you receive with the appliance.
38
Baumatic Consumables
o BC001 Degreaser for Dishwashers (200 g)
o BC002 Descaler for Washing Machines and Dishwashers (200 g)
o BC003 Ceramic Hob Cleaner (250 ml)
o BC004 Oven Cleaner (250 ml)
o BC005 Stainless Steel Cleaner and Protector (250 ml)
o BC007 E-Cloth – General Purpose Cloth
o BC008 Microwave Cover
To order a Baumatic consumable product please call 0123 5437 244
and quote the product code. You can also order online from
eshop.baumatic.co.uk
39
Technical Data (BWMI1206.1)
Manufacturer
Model Number
Rated Capacity of Standard Cotton
Program
Energy Efficiency Class
Annual Energy Consumption (1)
Energy Consumption of the Standard
60°C Cotton Program at Full Load
Energy Consumption of the Standard
60°C Cotton Program at Partial Load
Energy Consumption of the Standard
40°C Cotton Program at Partial Load
Power Consumption of Off Mode
Power Consumption of Left-On Mode
Annual Water Consumption (2)
Spin-drying Efficiency Class (3)
Maximum Spin Speed of Standard
Cotton Program
Remaining Moisture Content of
Standard Cotton Program
Standard Cleaning Cycle (4)
Program Duration of Standard 60°C
Cotton Cycle at Full Load
Program Duration of Standard 60°C
Cotton Cycle at Partial Load
Program Duration of Standard 40°C
Cotton Cycle at Partial Load
Noise Level
Installation Type
BAUMATIC LTD
BWMI1206.1
6 kg
A+
196 kWh
1.09 kWh
0.79 kWh
0.61 kWh
0.29 W
0.91 W
8900 litres
B
1200 rpm
52 %
Cotton 60°C/40°C
186 mins
113 mins
136 mins
60 dB washing / 74 dB spinning
Built-in
1) Energy consumption is based on 220 standard washing cycles for
cotton programmes at 60°C and 40°C at full and partial load,
and the consumption of the low-power modes. The actual energy
consumption will depend on how the appliance is used.
2) Water consumption is based on 220 standard washing cycles for
cotton programmes at 60°C and 40°C at full and partial load.
The actual water consumption will depend on how the appliance
is used.
3) Spin-drying efficiency is on a scale from G (least efficient) to A
(most efficient).
4) These programmes are suitable to clean normally soiled cotton
laundry and they are the most efficient programmes in terms of
combined energy and water consumption.
40
Technical Data (BWMI1407.1)
Manufacturer
Model Number
Rated Capacity of Standard Cotton
Program
Energy Efficiency Class
Annual Energy Consumption (1)
Energy Consumption of the Standard
60°C Cotton Program at Full Load
Energy Consumption of the Standard
60°C Cotton Program at Partial Load
Energy Consumption of the Standard
40°C Cotton Program at Partial Load
Power Consumption of Off Mode
Power Consumption of Left-On Mode
Annual Water Consumption (2)
Spin-drying Efficiency Class (3)
Maximum Spin Speed of Standard
Cotton Program
Remaining Moisture Content of
Standard Cotton Program
Standard Cleaning Cycle (4)
Program Duration of Standard 60°C
Cotton Cycle at Full Load
Program Duration of Standard 60°C
Cotton Cycle at Partial Load
Program Duration of Standard 40°C
Cotton Cycle at Partial Load
Noise Level
Installation Type
BAUMATIC LTD
BWMI1407.1
7 kg
A+
224 kWh
1.25 kWh
0.87 kWh
0.72 kWh
0.30 W
0.91 W
9600 litres
A
1400 rpm
45 %
Cotton 60°C/40°C
186 mins
113 mins
136 mins
58 dB spinning / 76 dB spinning
Built-in
5) Energy consumption is based on 220 standard washing cycles for
cotton programmes at 60°C and 40°C at full and partial load,
and the consumption of the low-power modes. The actual energy
consumption will depend on how the appliance is used.
6) Water consumption is based on 220 standard washing cycles for
cotton programmes at 60°C and 40°C at full and partial load.
The actual water consumption will depend on how the appliance
is used.
7) Spin-drying efficiency is on a scale from G (least efficient) to A
(most efficient).
8) These programmes are suitable to clean normally soiled cotton
laundry and they are the most efficient programmes in terms of
combined energy and water consumption.
41
United Kingdom
Baumatic Ltd.,
Baumatic Buildings,
6 Bennet Road,
Reading, Berkshire
RG2 0QX
United Kingdom
Sales Telephone
(0118) 933 6900
Sales Fax
(0118) 931 0035
Customer Care Telephone
(0118) 933 6911
Customer Care Fax
(0118) 986 9124
Spares Telephone
(01235) 437244
Advice Line Telephone
(0118) 933 6933
E-mail:
sales@baumatic.co.uk
customercare@baumatic.co.uk
spares@baumatic.co.uk
technical@baumatic.co.uk
Website:
www.baumatic.co.uk
Facebook:
www.facebook.com/baumatic.uk
Republic of Ireland
Service Telephone
1-890 812 724
Spares Telephone
091 756 771
Czech Republic
Baumatic CR spol s.r.o.
Lìpovà 665
460 01 Liberec 4
Czech Republic
+420 483 577 200
www.baumatic.cz
Slovakia
Baumatic Slovakia, s.r.o.
Galvániho 7/D
Slovakia
+421 255 640 618
Germany
Baumatic Gmbh
Bachstr.10-12
D-32 257 Bünde
Deutschland
+49 (0) 5223 99408 0
www.baumatic.de
Italy
Baumatic Italia S.R.L.
Via Galvani N.3
35011 Campodarsego (PD)
+3904 9920 2297
www.baumatic.it
Holland
Baumatic Benelux B.V.
Dukdalfweg 15d
1332 BH ALMERE
Nederland
+31(0)36 549 1553
www.baumatic.nl
43
44
44
44
13-04
--41038809
13-04
41038809
13.04 - 41038809
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising