Terzismo | M_PTL 3612 | Terzismo M_PTL 3612 User manual

Terzismo M_PTL 3612 User manual
2
Introduction
Read this manual carefully as it offers practical
advice to help you get the most from your washing
machine.
This «Instruction and Installation Manual» contains
everything you need to know about the everyday
running of your machine.
Please refer to this manual for installation and
maintenance instructions. The manual also contains
information about possible working problems,
advice about sorting clothes for washing, an
explanation of label symbols and hints about how to
remove stubborn stains.
1.- CONTROL PANEL
2.- LID
3.- DRUM
4.- DETERGENT DISPENSER
5.- PLINTH PANEL
6.- FILTER
Table of contents
page
Safety measures
Setting up - Installation
Guarantee
Preparing the wash. Opening/ closing the drum
Detergent load
Electronically-controlled variable load- Fuzzy Logic
Description of controls
Special programmes
General recommendations
Troubleshooting
Washing hints
3
5
6
7
8
8
9
13
14
16
17
Safety measures
This appliance meets the European Directives
2004/108/EC, 2006/95/EC which have been substituted
respectively by 89/336/EEC, 73/23/EEC and subsequent
modifications thereof.
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance
by a person responsible for their safety.
Children should be supervised to ensure that they do not play
with the appliance.
ATTENTION: FOR ALL CLEANING AND MAINTENANCE
WORK
• Remove the plug.
• Turn off the water inlet tap after each wash.
3
• The manufacturer fits all the machines with an earth
connection.
Ensure that the electrical installation has an earth connection
and that it is connected; if not, call a qualified Service Center.
The earth connection is essential for user safety as it eliminates the risk of electrical discharge.
• Power sockets should be in easily accessible places so that
the washing machine can be unplugged in case of any
problems.
• If the electric cable is damaged replace with an original set
(cable and plug) supplied by the manufacturer or official aftersales service.
note:
In the event that it is necessary to replace the power cable,
make sure that you comply with the following colour-code chart
during the wiring:
blue
neutral
brown
phase
Yellow-green
earth
The manufacturer accepts no responsibility for any
damage to people or things resulting from the failure to
comply with the appliance’s installation and safety
regulations.
• Do not touch the appliance with wet hands or feet.
• Do not use the appliance when bare-footed.
• Use extension cords only with extreme care.
• Do not use adapters or multiple plugs.
• Do not allow the appliance to be used by children or the infirm
without due supervision.
• Do not pull on the power cord or the appliance itself to remove
the plug from the socket.
• Do not leave the appliance outdoors or exposed to the
atmospheric elements (rain, sun, etc.).
• Do not cover the appliance with cloth or plastic while it is
working.
• Do not install the appliance in damp places or anywhere
where it could be sprayed by the shower.
• Do not install the appliance on a surface which obstructs the
space between the floor and the base of the machine.
• Keep all packaging out of the reach of children as it could
constitute a health hazard.
ATTENTION:
DURING A WASH CYCLE THE WATER
CAN REACH TEMPERATURES OF 90ºC.
4
Setting up - Installation
• Unpack the appliance.
• Remove the 4 screws (A) from
both clamps and the 4
screws (B).
• Replace the 4 screws (A) and
fit the trims provided (D).
If your model offers this function:
Position the protection sheet as shown in the
diagram.
1.- Washing machine with wheel trolley.
2.- Washing machine without wheel trolley.
ATTENTION: DO NOT TURN THE TAP ON
• The washing machine should be connected to the
water mains via the new tube supplied with the
appliance (inside the drum). Do not use the old tube for
this purpose.
• Connect one end of the water inlet pipe with the elbow
bend to the electrovalve (top rear part of the machine)
and the other end to a tap or a plumbed-in 3/4" gas
threaded connection.
• Place the washing machine close to the wall, ensuring
that there are no bends or kinks anywhere in the tube.
Hook the outlet pipe to the edge of the sink or preferably
to a fixed drainage outlet of a diameter greater than that
of the outlet pipe and at a height of min. 50 cm. and a
maximum of 75 cm. from the floor.
If necessary, use the curved accessory to attach and
support the outlet pipe more securely.
5
If your model offers this function:
• To move the washing machine easily, turn the trolley
lever to the right. Once you have finished moving the
machine, return the lever to its original position.
• Level the machine by adjusting the front feet.
a) Turn the nut clockwise to release the screw on the
foot.
b) Raise or lower the foot by rotating it until it stands
firmly on the floor.
c) Lock the foot in position by turning the nut
anticlockwise until it comes up against the bottom of the
washing machine.
Check that the appliance is properly levelled.
Check that the washing machine does not rock by trying
to move two diagonally opposite top corners at the
same time.
• If you move the washing machine from one place to
another, you must level the feet again afterwards.
• Connect the machine.
6
Preparing the wash. Opening/ closing the drum
ATTENTION:
IT IS IMPORTANT TO MAKE SURE THAT THE
DRUM IS CAREFULLY OPENED AND CLOSED,
OTHERWISE THE MACHINE OR LAUNDRY
COULD GET DAMAGED.
ENSURE THAT THE DOORS FIT TOGETHER
PERFECTLY AND ARE PROPERLY CLOSED.
Loading
1.
Open the washing machine lid.
2.
Open the drum by pressing the (A) button with one
hand while pressing down on the opposite door
with the other.
3.
Place clothes in the drum one item at a time, and
without squashing. Do not exceed the load limits
recommended in the “programme table”. An
overloaded washing machine will not wash
properly, and will leave clothing wrinkled.
(A)
4.
To close the drum, place the doors so that the one
with the (A) button is below the other and they fit
together perfectly.
7
Detergent load
II
Maximum Main wash
washing powder
I
Maximum pre-wash
washing powder
recommended
Maximum Main wash
washing liquid
Maximum scenting agent
The detergent dispenser is divided into 3 compartments:
.- Compartment I is for the pre-wash detergent.
.- Compartment II is for the main wash detergent.
is for fabric conditioners, scenting agents and special additives such as starch,
.- The compartment
blueing, etc.
The detergent dispenser has two reference marks:
.- Recommended (lower reference mark). This indicates the recommended level for the pre-wash and
main wash compartments.
.- Max. This indicates the maximum level, which should never be exceeded.
Important:
- Do not use liquid detergent for programs with a prewash cycle and/or timed start.
When the clothes present stains that need treatment with bleaches liquids products, you can proceed
to their preliminary cleaning in the washing machine. For that: Introduce the bleach product in the
"compartment II", and set the rinse program . Once finished set the programmer to the OFF position,
add the rest of the laundry, and proceed with a normal was program.
Electronically- controlled Variable Load – Fuzzy Logic
This machine has electronics that automatically process all stages of the wash to ensure exceptional
results and at the same time save you time and money.
Once a programme has been selected, the machine optimises the following elements depending on
the wash load and type of fabric:
- quantity of water and power consumption
- wash time
- rinse efficiency
The washing machine also:
- detects suds and increases the amount of rinse water if necessary
- adjusts spin speed according to load distribution, thus forestalling any imbalance in the mechanism.
8
Description of controls
H B2
G
B1
V
A
C2
A
C1
p
PROGRAMME SELECTOR
Use this control to select the desired wash programme. Turn the selector (it
can be turned in both directions) so that the programme is opposite the
reference indicator (p). The temperature selected will depend on the
programme. (See the Programme Table).
B1 SPIN SPEED SELECTOR
B2 DELAYED START KEY
C1 COLD WASH
C2 AQUAPLUS (SENSITIVE KEY)
G
DOOR LOCK LAMP
H
START/PAUSE KEY
V
“DIGITAL” Display
The display’s indicator system allows you to be constantly informed
about the status of the machine
p
CONTROL POSITION INDICATOR
9
Programme table mod PTL 3612
programme
COTTONS
MIXED
SYNTHETICS
DELICATES
SPECIAL
programme for
aprox.
time
min.
max.
temp.
setting
ºC
spin
speed
rpm/min
max.
load
Kg.
washing powder option keys
load
C
+
Cold
I
II
Aqua
Fast coloureds with prewash
display
90º
1200
6




* Fast coloureds
display
60º
1200
6





* Fast coloureds
display
40º
1200
6




Delicate coloureds
display
30º
1200
6




Fast coloureds
display
50º
1000
3




Delicate coloureds
display
40º
1000
3




Delicate coloureds
display
30º
1000
3




Wool
display
30º
800
1



Hand wash
display
40º
800
1



Rinse
display
1000
Spin
display
1200
Drain
display
Class A59
display
60º
1200
3



Rapid 44
display
40º
1000
3



Rapid 30
display
30º
1000
2





0
* Programme as per EN 60456
Technical data mod. PTL 3612
Mains
voltage
220-230V.
50Hz.
Wash
power
rating
Spin
Power
rating
Pump
Motor
Power
rating
Heating
element
power
rating
Max.
Power
input
Mains
Fuse
Amp.
rating
175 W.
340 W.
30 W.
1300 W.
1500 W.
10 A.
Water
pressure
0,05-0,8 Mpa
Water
Energy
consumption consumption
*prog.
*prog.
EN60456
EN60456
49 L.
0,90 Kw.
IMPORTANT: Do not use liquid detergent for programs with a prewash cycle and/or time delay.
PREPARING THE WASH CYCLE
1.- Once the washing is loaded, ensure that the drum doors are properly closed..
2.- Add detergent and additives, not exceeding the maximum level indicator.
.- detergent for pre-wash I
.- detergent for wash programme II
.- fabric conditioner
10
SELECTING THE DESIRED PROGRAMMES AND OPTIONS
3.- Turn the programme selector (A) to the desired programme.
4.- Press the key or keys for any options desired (C1, C2 ).
.- It is advisable to select the required options before pressing the Programme Start key (H).
.- Remember that if the programme has already passed the stage at which an option is activated, that
option will not be implemented.
C1 cold wash key
By pressing this button it is possible to transform every programme into a cold washing one, without
modify other characteristics (water level, times, rythmes, etc..).
Curtains, small carpets, man made delicate fabrics, non coulor fast garments can be safely washed thanks
to this new device.
C2 aquaplus (sensitive key)
Thanks to the new SENSOR ACTIVA SYSTEM, by pressing the key it is possible to run a special washing
cycle applicable to all programs and types of fabric, caring for their fibres and the delicate skin of the users
who use them.
Taking on much more water, together with the new combined action of drum rotation cycles and taking on
and discharging water allow you to obtain perfectly clean, rinsed clothes. More water is used in the wash
to dissolve the detergent completely, ensuring an effective washing action. The water in the rinses has
also been increased to eliminate all trace of detergent in the fibres.
This function has been specifically studied for people with delicate, sensitive skin, who can suffer irritation
or allergy from the slightest detergent residue.
It is also advisable to use this function for children's clothes and delicate fabrics in general, especially for
washing bathrobes, whose fibres tend to retain detergent.
This option is not available for the wool program.
5.- Select spin speed if required (B1)
B1 spin speed
Once the programme has been selected, the maximum spin speed allowed for that programme appears
on the display. Pressing the spin button will reduce the speed by 100 rpm each time the button is
pressed. The minimum speed allowed is 400 rpm, or it is possible to omit the spin by pressing the spin
button repeatedly.
6.- To start the programme, once options have been chosen, press the key H. The washing machine will
begin to operate. If you wish to cancel the option you have selected, press the key again. (The pilot light
will go off).
B2 Time delay button
This button allows you to pre-programme the wash cycle to delay the start of the cycle for up to 24 hours.
To delay the start use the following procedure:
Set the required programme.
Press the button once to activate it (h00 appears on the display) and then press it again to set a 1 hour
delay (h01 appears on the display); the pre-set delay increases by 1 hour each time the button is pressed,
until h24 appears on the display, at which point pressing the button again will reset the delay start to zero.
Confirm by pressing the “START/PAUSE” button (the light on the display starts to flash). The countdown
will begin and when it has finished the programme will start automatically.
It is possible to cancel the delay start by taking the following action:
Press and hold the button for 5 seconds until the display will show the settings for the programme
selected.
At this stage it is possible to start the programme previously selected by pressing the “START/PAUSE”
button or to cancel the process by setting the selector to the OFF position and then selecting another
programme.
cycle duration (V)
When a programme is selected the display automatically shows the cycle duration, which can vary,
depending on the options selected.
Once the programme has started you will be kept informed constantly of the time remaining to the end of
the wash.
11
Door lock light (G)
Once the START/PAUSE button has been pressed the light first flashes then stops flashing and remains
on until the end of the wash.
2 minutes after the end of the wash the light goes off to show that the door can now be opened.
Cancel-change programs
Once you have started a program, and wish to change or cancel it, you should proceed in the following
manner,
- Put the program selector in the OFF position. At that instant, you have cancelled the program and can
if you wish to do so, select a new one.
- Select the new program.
- Click the key (H) again.
The washing machine will perform the new selected program.
Programme pause
It is possible to momentarily stop the wash programme so that more washing can be added, and to do so,
proceed as follows:
- Hold down the (H) key until the option key lamps begin to flash and the time remaining indicator display,
and pilot lamp lights up.
- When the Door Lock lamp goes out (after approx. 2 minutes), open the door and add the desired
washing.
- Correctly close the doors of the drum and the outer cover.
- Press the key H, and the washing machine will continue with the programme.
When the programme has been completed, the message "END" will appear in the indicator display,
Wait until the Door Lock lamp (G) goes out (after approx. 2 minutes)
“To remove the washing, set the programme selector to the OFF position”, before opening the
washing-machine lid and the drum doors.
12
Specific / special programmes
RINSE
SPECIAL RINSE PROGRAMME
Programme rinse runs 3 rinses with spins at 800 rpm (this speed may be reduced or spin
cancelled using the appropriate button). It works for all fabrics and can be used, e.g. after
garments are hand washed.
SPECIAL HIGH-SPEED SPIN PROGRAMME
Programme spin runs a spin at the speed indicated in the programme table.
SPIN
DRAIN
DRAIN
Programme drain empties the water from the machine.
HAND
WASH
HAND WASH : The programme runs a complete wash cycle for garments intended to be
hand washed. It washes at no more than 30 ºC and finishes with three rinses and a
delicate spin.
CLASS 59’
A CLASS 59’ : It is possible to obtain an optimum wash performance with a maximum
load of 3 kg at a temperature of 60 degrees C with a considerable reduction in time.
RAPID PROGRAMMES
RAPID
44´ MINUTE RAPID PROGRAMME
30´ MINUTE RAPID PROGRAMME
These programmes run a complete wash cycle at 40/50 ºC for up to 3.5 kg of washing in
44 or 30 minutes.
REMARKS
1. For heavily soiled washing we recommend loads of no more than 4 kg.
2. The machine is designed to apply fabric softener automatically in the last rinse of
all wash cycles.
13
General recommendations
CLEANING AND MAINTENANCE OF THE MACHINE
Do not use abrasives, spirits or solvents when cleaning the exterior of the washing machine. It is sufficient
to use a damp cloth.
The washing machine requires very little maintenance.
• Drying the rubber seal of the drum.
• Cleaning the dispenser and its compartments.
• Cleaning the filter.
• Cleaning prior to removals or when the machine is to stand idle for long periods.
To help conserve the washing machine, dry the rubber seal and leave the door open when the
cycle ends.
CLEANING THE FILTER
The washing machine comes with a special filter, located behind the machine’s front plinth panel, that
collects larger objects (coins, buttons, etc.) which could even block the pump.
It is advisable to clean the filter whenever the machine fails to rinse the clothes as well as it should
or when it fails to drain properly.
When it is necessary to clean the filter, proceed as follows:
• Use a basin to collect the water coming out.
• Remove the filter and clean it.
• Once the filter is clean, replace it by following the abovementioned pro in reverse.
14
CLEANING THE DETERGENT DISPENSER AND ITS COMPARTMENTS
.- It is advisable to clean the three compartments of the
detergent dispenser (pre-wash, wash, and fabric conditioner)
from time to time. To do this, remove the detergent dispenser
and after cleaning it, fit it back in place.
To remove and fit the detergent dispenser, follow the steps
indicated in the images.
A
removing
.- Press button A
.-Hold down the button and pull the detergent dispenser
outwards
II
I
.- Remove the dispenser and clean it
.- In the case of the pre-wash (I) and wash (II) compartments,
it is advisable to remove any dried-in remains of detergent
which obstruct the flow of the detergent to the drum.
S
.- In the fabric conditioner compartment, the trap (S) located at
the rear part of the dispenser should be removed by pulling
them out.
Remove any solid residue which could block the holes in the
compartments.
B
fitting
.- Fit in the tabs as shown
C
.- Push the detergent dispenser towards the housing (C) in the
door until the tab clicks into place.
15
Troubleshooting
FAULT
1.- No programme works
CAUSE
• The appliance is not plugged
in.
• The general switch is disconnected.
• There is no electricity.
• The fuses in the electric installation are damaged.
• The door is open.
SOLUTION
• Plug it in.
2.- The appliance does not
load water
• See causes for 1.
• The tap is turned off.
• Check.
• Turn on the tap.
3.- The water does not drain
• The filter is clogged.
• The outlet pipe is bent.
• Check the filter.
• Straighten the outlet pipe.
4.- The spin function does not
work
• The washing machine has not
yet drained the water.
• The “Spin Exclusion” option is
activated.
• Wait a few minutes for the washing machine to drain.
• Enable the spin option.
• The washing machine is not
correctly levelled.
• The anchoring device for transport has not been removed.
• The wash load is not evenly
distributed.
• Adjust the feet.
• The wash load is not evenly
distributed within the drum.
• Distribute the wash load evenly
in the drum.
• Contact technical service.
5.- Strong vibrations during
spin cycle
6.- The high-speed spin does
not work
7.- Display will show error nº
0,1,5,6,7,8,9,12,13,15,16
• Activate the general switch.
• Check.
• Check.
• Close the door.
• Remove the transport support.
• Distribute it evenly.
8.- Display will show error nº 2 • Machine does not fill with water
• Check that water inlet tap is open.
9.- Display will show error nº 3 • Water does not empty from
machine
• Check that outlet is not clogged
• Check for kinks in outlet tube.
10.-Display will show error nº 4 • Too much water in machine.
• Shut off water tap.
• Contact technical service
If the problem or malfunctioning persists, disconnect the
machine, turn off the tap and do not try to repair.
For all repairs contact an Official Technical Assistance centre
(consult the European guarantee sheet) and always insist on the
use of original parts. Failure to do so may compromise the safety
of your machine.
When contacting a Technical Assistance Centre always refer to
the model (see also control panel) and the registration and serial
numbers indicated on the plate at the bottom front of the
machine behind the plinth panel or on the guarantee certificate.
That is to say, everything that appears in the box.
Providing this information will ensure a faster and more efficient
service.
16
Washing hints
Hints on the most economical, most environmentally friendly way to use your washing machine.
HINTS ON USING YOUR WASHING MACHINE
Wait until you have a full load before using the machine: this will avoid the use of more water and power
than necessary.
We recommend using the full load capacity: this could save you up to 50% in power consumption. Wash a
single full load rather than two light loads.
WHEN IS PRE-WASHING NECESSARY?
Only when washing heavily soiled clothes.
With clothes that are not especially dirty, you can save between 5 and 15% by not using this option.
WHAT WASH TEMPERATURE SHOULD I USE?
Applying a stain remover before placing clothes in the machine will eliminate the need for wash
temperatures of more than 60 ºC.
When loading a wash into the drum, we recommend that you:
• For specially delicate garments we recommend the use of a protective net.
• Empty all pockets and ensure that they do not contain metal objects (paperclips, safety pins, pins,
coins,etc.).
• Fasten pillow slips, close all zips and fastenings, and tie any loose ribbons or belts from dresses.
• Remove all runners (metal and plastic) from curtains and net curtains. We recommend that the ribbon be
gathered into a ball and tied with its own cord.
• Unfold all items to be washed.
• Be careful not to exceed the recommended load for each programme.
• When washing rugs, bedspreads and other highly absorbent items, cancel the spin option.
• In order to be able to wash woollens in the washing machine they must carry the “Pure New Wool”
symbol as well as the information “does not become matted” or “machine washable”.
• If possible, do not wash only towels. Mix them with your regular washing.
• Ensure that no item becomes trapped between the drum doors.
LABEL SYMBOLS
Labels are usually sown into the collar or side seams. The symbols which appear on them indicate the
following:
• Maximum WASH temperature.
• Appropriate and inappropriate washing methods.
• Appropriate and inappropriate washing products.
The symbols are as follows:
WASH
Washing instructions always appear as a basin with different indications:
•
Do not wash.
•
Can be washed both by hand or in the washing machine. The figures in the basin indicate the
maximum wash temperature.
•
Hand wash only.
When the hand is half submerged in the water, this means that the item should be tumbled only
gently during washing. If it is fully submerged in the water, this means that the garment should
only be washed by hand.
•
The line under the basin means that the item should be washed on a gentle cycle.
•
Do not spin.
BLEACH
Bleach is widely used to whiten fabrics, although in some cases it can cause irreparable damage. There
are various symbols which refer to its use.
• Bleach can be used.
• Do not use bleach.
17
Please record the following information:

Model

Serial No.

Name of distributor

Date of purchase
The manufacturer reserves the right to make any technical modifications
due to product improvement. No prior notice will be given.If you have
any enquiry,please contact our after-sales department and forgive for
any inconvenient.
All information is subjected to English version.
香港仔大道232都工業大廈二樓
產品查詢 : 2418 3246
維修安裝 : 8210 8210
2/F, Shing Dao Industrial Building,
232 Aberdeen Main Road,Hong Kong
Product information : 2418 3246
Service Hotline : 8210 8210
18
請記錄下列資料

型號

機身編號

經銷商名稱

購買日期
本產品不斷改進中,如功能有所更改,恕不另通知,如有疑問,請與維修
中心聯絡,不便之處,敬請原諒。
說明書以內容以英文版本為準。
香港仔大道232都工業大廈二樓
產品查詢 :2418 3246
維修安裝 : 8210 8210
2/F, Shing Dao Industrial Building,
232 Aberdeen Main Road,Hong Kong
Product information : 2418 3246
Service Hotline : 8210 8210
19
WEEE
This appliance is marked according to the European directive 2002/96/EC on Waste Electrical and
Electronic Equipment (WEEE).
By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for
the environment and human health, which could otherwise be caused by inappropriate waste handling of
this product.
The symbol on the product indicates that this product may not be treated as household waste. Instead it
shall be handed over to the applicable collection point for the recycling of electrical and electronic
equipment
Disposal must be carried out in accordance with local environmental regulations for waste disposal.
For more detailed information about treatment, recovery and recycling of this product, please contact your
local city office, your household waste disposal service or the shop where you purchased the product.
EN
The manufacturer declines all responsibility in the event of any printing
mistakes in this booklet. The manufacturer also reserves the right to make
appropriate modifications to its products without changing the essential
characteristics.
16.05.2013/ M- 46007341 EN
20
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising