Terzismo | PWD6414S | Terzismo PWD6414S., PWD6414S User manual

Terzismo PWD6414S., PWD6414S User manual
Washer Dryer
Instructions Manual
PWD6414S
hgfhfhjgf
Contents General safety rules
Page
– This appliances is intended to be used in household and similar
Introduction
2
applications such as:
General
delivery
notes
4
• Staff
kitchen areas in shops, offices and other working
environments;
Safety
notes
4
•
Farm
houses;
Quick start
5
• By clients in hotels, motels and other residential type
Description
of controls
6
environments;
Programme
Table use of this appliance from household environment
14 or
A different
from typical
expert
Programme
selectorhousekeeping functions, as commercial use by 16
or
trained
users,
is
excluded
even
in
the
above
applications.
Detergent drawer
19If the
appliance is used in a manner inconsistent with this it may reduce the
Detergents,
washing
aids andand
amounts
to void
use the manufacturer’s warranty.
20 Any
life of the
appliance
may
Useful
advice for
22
damage
to the
theuser
appliance or other damage or loss arising through
use
that
is
not
consistent
with
domestic
or
household
use
The main wash
23(even
if
located
in
a
domestic
or
household
environment)
shall
not be
Drying
25
accepted by the manufacturer to the fullest extent permitted by law.
Automatic washing/drying cycle
26
– This appliance is not intended for use by persons (including
Drying cycle
27
children) with reduced physical, sensory or mental capabilities,
Cleaning
and routine
maintenance and knowledge, unless they have29been
or lack
of experience
given supervision
Investigating
malfunctions or instruction concerning use of the appliance
31
by
a
person
responsible
for
their
safety.
Technical data
33
Children shall not play with the appliance. Cleaning and user
Setting up + installation
34
maintenance shall not be made by children without supervision.
– Children should be supervised to ensure that they do not play with
the appliance.
– Children of less than 3 years should be kept away unless
BEFORE SWITCHING ON THE APPLIANCE MAKE SURE
continuously supervised.
IT IS CORRECTLY INSTALLED AND THAT THE TRANSIT
– If the supply cord is damaged, it must be replaced by the
SCREWS ARE
ASor
SHOWN
PAGE
manufacturer,
itsREMOVED
service agent
similarlyINqualifi
ed 34.
persons in
order to avoid a hazard.
– Only use the hose-sets supplied with the appliance for the water
supply connection (do not reuse old hose-sets).
– Water pressure must be between 0,05 MPa and 0,8 MPa.
– Make sure that a carpet do not obstruct the base of the machine and
ventilation openings.
– The OFF condition is reached by placing the reference mark on
the programmes control/knob in the vertical position. Any other
different position of such control sets the machine in ON condition
(only for models with programmes knob).
3
– The final part of a washer dryer cycle occurs without heat (cool
General delivery notes
down cycle) to ensure that the items are left at a temperature that
ensures that the items will not be damaged.
On delivery check that there is the following with the appliance:
–WARNING:
Instruction manual
never stop a washer dryer before the end of the drying
–cycle
Certificate
of guarantee
unless
all items are quickly removed and spread out so that the
–heat
Capsis dissipated.
– Inlet hose
– Liquid detergent or liquid bleach compartment
– After installation, the appliance must be positioned so that the plug
and
that no damage has occurred during transit, and if so, call your nearest
ischeck
accessible.
Authorised Technical Support Service agent (see Customer Service)
– The appliance must not be installed behind a lockable door, a
sliding door or a door with a hinge on the opposite side to that of the
washer dryer, in such way that a full opening of the washer dryer
door is restricted.
Safety notes.
– The maximum load capacity of dry clothes depends on the model
used (see control panel).
Note: for any cleaning or maintenance procedure for the
– The appliance is not to be used if industrial chemicals have been
washing
machine
used for cleaning.
– Do not dry unwashed items in the washer dryer.
A) Pull out the plug
Turn offthat
the tap
–B)Items
have been soiled with substances such as cooking oil,
C)acetone,
Gorenje equips
all its petrol,
appliances
with earthing.
Ensure
that the mains
supply is earthed,
alcohol,
kerosene,
spot
removers,
turpentine,
waxes
and
if
it
is
not,
seek
assistance
from
a
qualified
person.
and wax removers should be washed in hot water with an extra
D)amount
Do not touch
the appliance before
when hands
or feet
are wet
damp.
Do not dryer.
use the
of detergent
being
dried
in orthe
washer
appliance with bare feet.
The usesuch
of adapters,
multiple
connectors
and/or
extensions
is not recommended.
–E)Items
as foam
rubber
(latex
foam),
shower
caps, waterproof
textiles, rubber backed articles and clothes or pillows fitted with
foam
Note:rubber pads should not be dried in the washer dryer.
water temperature
can reach
90°Cshould
duringbe
theused
wash
– Fabric
softeners, or similar
products,
as cycle
specified
by the fabric softener instructions.
Check there is noitems
water leftcan
in theignite
drum before
opening the door. especially when
–F) Oil-affected
spontaneously,
G)exposed
This appliance
is
not
intended
for
use
by
persons
(including
children)
reduced
to heat sources such as a washer
dryer.
Thewith
items
become
physical,
sensory
or
mental
capabilities,
or
lack
of
experience
and
knowledge,
unless
warm, causing an oxidation reaction in the oil, Oxidation creates
heat.
they
have
been
given
supervision
or
instruction
concerning
use
of
the
appliance
by afire.
If the heat cannot escape, items can become hot enough to catch
person responsible for their safety.
Piling,
stacking or storing oil-effected items can prevent heat from
Children should be supervised to ensure that they do not play with the appliance.
escaping
and
so create
a fiappliance
re hazard.
H) Do not pull the
power
cable or the
itself to remove the plug from the socket.
I)
The
appliance
must
not
be
exposed
to
weather
conditions (rain,
direct sun, oil
etc...)
– If it is unavoidable that fabrics contain vegetable
or cooking
or have
L) been
When moving
the
appliance
never
lift
it
by
the
controls
or
by
the
detergent
drawer.
contaminated by hair care products be placed in a washer
When in
transit
never rest
thebe
doorwashed
against theintrolley
or transport
theextra
appliance
without
dryer
they
should
first
hot water
with
detergent
the
polystyrene
base.
- this will reduce, but not eliminate, the hazard.
4
M) N.B!
If the appliance
installed from
on a carpeted
floorsuch
ensureas
thatlighters
the ventilation
on the
– Remove
all isobjects
pockets
and holes
matches.
base of the appliance are not obstructed.
instructions
N)Safety
If the appliance
is not running properly or breaks down, switch it off, turn off the tap and do
not
tamper
with
the appliance.
– Before cleaning
or maintaining the washing machine, unplug the
Consult
only
the
Authorised
Support
Service for possible repair and ask them to
appliance and
turn offTechnical
the water
faucet.
use original spare parts.
– Make
is the
grounded.
Otherwise, seek
Failure tosure
complythe
with electrical
the above cansystem
compromise
safety of the appliance.
ed professional
O)qualifi
If the appliance’s
power cableassistance.
should ever need replacing, consult the Authorised
Technical Support Service
– Please do not use converters, multiple sockets or extension cords.
Quick start
WARNING: water may reach very high temperatures during
the wash cycle.
Washing
- Make
Open thesure
door by
using the
“A” (Fig.in
1, page
–
there
is handle
no water
the 6)drum before opening the
- porthole.
Select laundry and put it in the machine
- Close the door
- Do
Put not
detergent
compartments
as indicated
in the programme
guidethe
in this
instruction
–
pull in
onthethe
power cord
or appliance
to unplug
machine.
manual
–
notprogramme
expose the washing machine to rain, direct sunlight or other
- Do
Select
weather
- The displayelements.
will show the settings for the programme selected.
-– Adjust the wash temperature if necessary.
When moving, do not lift the washing machine by the knobs or
detergent
DRYING drawer; during transport, never rest the porthole on the
trolley.
If you would like the drying cycle to begin automatically after
We
recommend
lift the washing
machine.
washing,
selecttwo
thepeople
programme
required
using the Drying
Selection
button.
– In the event of fault and/or malfunction, turn off the washing machine,
Otherwise it is possible to finish the wash and then decide on the
close
water faucet
dryingthe
programme
and and
load.do not tamper with the appliance.
Immediately contact our Customer Service Centre and only use
original spare parts. Failure to observe these instruction may
Press additional
function buttons
jeopardise
appliance
safety.(if required)
-
Press the “Start/Pause” button (page 7)
The programme starts.
After washing
The word “End” will appear on the display.
Wait for the door lock to be released
(about 2 minutes after the programme has finished).
The “Door Security” indicator light will go out.
Switch off the washing machine by turning the
selector to “OFF” position.
Open the door and remove the laundry.
Ensure that the machine is correctly installed in line with the instructions found on page 34.
5
Contents
Page
General safety rules
General delivery notes
Quick start
Description of controls
Programme Table
Programme selector
Detergent drawer
Detergents, washing aids and amounts to use
Useful advice for the user
The main wash
Drying
Drying cycle
Automatic washing/drying cycle
Cleaning and routine maintenance
Investigating malfunctions
Technical data
Setting up + installation
3
7
7
8
16
18
21
22
24
25
27
28
29
31
33
35
36
BEFORE SWITCHING ON THE APPLIANCE MAKE SURE
IT IS CORRECTLY INSTALLED AND THAT THE TRANSIT
SCREWS ARE REMOVED AS SHOWN IN PAGE 36.
Please read these instructions for use carefully and all other information
enclosed with the washing machine.
Keep all documentation in a safe place for future reference or for any future
owners.
6
General delivery notes
On delivery check that there is the following with the appliance:
– Instruction manual
– Certificate of guarantee
– Caps
– Inlet hose
and check that no damage has occurred during transit, and if so, call your nearest
Authorised Technical Support Service agent (see Customer Service)
Quick start
Washing
-
Open the door by using the handle “A” (Fig. 1, page 8)
Select laundry and put it in the machine
Close the door
Put detergent in the compartments as indicated in the programme guide in this instruction
manual
Select programme
The display will show the settings for the programme selected.
Adjust the wash temperature if necessary.
DRYING
If you would like the drying cycle to begin automatically after
washing, select the programme required using the Drying
Selection button.
Otherwise it is possible to finish the wash and then decide on the
drying programme and load.
Press additional function buttons (if required)
-
Press the “Start/Pause” button (page 10)
The programme starts.
After washing
The word “End” will appear on the display.
Wait for the door lock to be released
(about 2 minutes after the programme has finished).
The “Door Security” indicator light will go out.
Switch off the washing machine by turning the
selector to “OFF” position.
Open the door and remove the laundry.
Ensure that the machine is correctly installed in line with the instructions found on page 36.
7
Description of controls
Fig. 1
N
B
EM
L
O
DI NB
PP
90
60
40
30
20
FO
HH
G IF CE LDMC
G
AA
Door handle
"Door Security" indicator light
"Start/Pause" button
"Drying Selection" button
"Temperature" button
"Delay Start" button
"Sensitive Care" button
"Stain Blaster " button
"Spin" Selection button
Digital Display
"Wash Time" button
Programme selector with "OFF" position
Buttons indicator light
Detergent drawer
8
A
B
C
D
E
F
G
H
I
L
M
N
O
P
“Kg MODE”
(Function active only on Cotton and Synthetics programmes)
Through every wash phase “Kg MODE” allows to monitor information on the wash load in the
drum.
So, as soon as the “Kg MODE” is set in motion, in the first 4 minutes of the wash, it:
- adjusts the amount of water required
- determines the length of the wash cycle
- controls rinsing
according to the type of fabric selected to be washed it:
- adjusts the rhythm of drum rotation for the type of fabric being washed
- recognises the presence of lather, increasing, if necessary, the amount of water during rinsing
- adjusts the spin speed according to the load, thus avoiding any imbalance.
In this way “Kg MODE” is able to decide, by itself, the most suitable programme for each
individual wash from the hundreds of possible wash combinations.
“Kg MODE” meets the need for easy use by permitting a simplified programme selection.
Infact, the user need only tell the machine the type of fabric in the drum and the degree of
soiling, to obtain a perfect wash with the highest level of drying possible with a spin which
really cares for your clothes.
9
Door handle
Press the finger-bar inside the door handle to open the door.
DOOR SECURITY indicator light
A
B
The “Door Security” indicator light is illuminated when the door is fully closed and the machine is ON.
When "Start/Pause" is pressed on the machine with the door closed the indicator will flash
momentarily and then illuminate.
If the door is not closed the indicator will continue to flash.
A special safety device prevents the door from being opened immediately after the end of the cycle.
Wait for 2 minutes after the wash cycle has finished and the “Door Security” light has gone out
before opening the door. At the end of the cycle turn the programme selector to "OFF" .
C
“START/PAUSE” button
Press to start the selected cycle .
NOTE: When the "Start/Pause" button has been pressed,
the appliance can take few seconds before it starts
working.
Changing the settings after the programmes has started (PAUSE)
Press and hold the "Start/Pause" button for about 2 seconds, the flashing lights on the
options buttons and time remaining indicator will show that the machine has been paused,
adjust as required and press the "Start/Pause" button again to cancel the flashing lights.
If you wish to add or remove items during washing, wait 2 minutes until the safety device
unlocks the door.
When you have carried out the manoeuvre, close the door, press "Start/Pause" button and
the appliance will continue working where it left off.
CANCELLING THE PROGRAMME
To cancel the programme, set the selector to the "OFF" position.
Select a different programme.
Re-set the programme selector to the "OFF" position.
10
The option buttons should be selected before pressing
the "Start/Pause" button.
“DRYING SELECTION” button
D
With the programme selector not in the OFF position, press the button to select the required
drying programme; an indicator will light to display the drying result selected each time you
press the button.
To cancel the selection before the start of a drying programme, press the button repeatedly
until the indicators go out or return the programme selector to the OFF position.
To cancel the cycle during the drying phase, hold the button down for 2 seconds until the
cooling indicator lights up; given the high temperature inside the drum, we recommend that
you allow the dryer to complete the cool down period before returning the programme
selector to the OFF position and removing the laundry.
“TEMPERATURE” selection button
E
When a programme is selected the relevant indicator will light up to show the recommended
wash temperature.
The Temperature button can be used to decrease or increase the temperature of your chosen
wash cycle.
Each time the button is pressed, the new temperature level is shown on the WashTemperature
Indicator.
If you want carry out a cold wash all the indicators must be off.
F
“DELAY START” button
This button allows you to pre-programme the wash cycle to delay the start of the cycle for up
to 24 hours.
To delay the start use the following procedure:
Set the required programme.
Press the button once to activate it (h00 appears on the display) and then press it again to set
a 1 hour delay (h01 appears on the display); the pre-set delay increases by 1 hour each time
the button is pressed, until h24 appears on the display, at which point pressing the button
again will reset the delay start to zero.
Confirm by pressing the "Start/Pause" button (the light on the display starts to flash). The
countdown will begin and when it has finished the programme will start automatically.
11
It is possible to cancel the delay start by taking the following action:
Press and hold the button for 5 seconds until the display will show the settings for the
programme selected.
At this stage it is possible to start the programme previously selected by pressing the
"Start/Pause" button or to cancel the process by setting the selector to the “OFF” position
and then selecting another programme.
Warning: If there is any break in the power supply while
the machine is operating, a special memory stores the
selected programme and, when the power is restored, it
continues where it left off.
G
“SENSITIVE CARE” button
By pressing this button you can activate a special new wash cycle in the Cotton and Mixed
Fabrics programs, thanks to the new Sensor System. This option treats with care the fibres of
garments and the delicate skin of those who wear them.
The load is washed in a much larger quantity of water and this, together with the new combined
action of the drum rotation cycles, where water is filled and emptied, will give you garments which
have been cleaned and rinsed to perfection. The amount of water in the wash is increased so that
the detergent dissolves perfectly, ensuring an efficient cleaning action. The amount of water is also
increased during the rinse procedure so as to remove all traces of detergent from the fibres. This
function has been specifically designed for people with delicate and sensitive skin, for whom even
a very small amount of detergent can cause irritation or allergy.
You are advised to also use this function for children’s clothing and for delicate fabrics in general,
or when washing garments made of towelling, where the fibres tend to absorb a greater quantity of
detergent. To ensure the best performance for your wash, this function is always activated on the
Delicates and Woollens/Handwash programs.
H
“STAIN BLASTER” button
By pressing this button, which can only be activated in the Cotton cycles, the sensors in the
new system come into operation. They affect both the selected temperature, keeping it at a
constant level throughout the wash cycle, and the mechanical function of the drum.
The drum is made to turn at two different speeds at crucial moments. When the detergent
enters the garments, the drum rotates in such a way that the detergent is distributed in a
uniform manner; during the wash and rinse procedures, however, the speed increases in
order to maximise the cleaning action. Thanks to this special system, the efficiency of the
wash procedure is improved WITHOUT ANY INCREASE IN THE LENGTH OF THE
PROGRAM.
12
I
“SPIN” button
The spin cycle is very important to remove as much water as possible from the laundry without
damaging the fabrics. You can adjust the spin speed of the machine to suit your needs.
By pressing this button, it is possible to reduce the maximum speed, and if you wish, the spin cycle
can be cancelled. To reactivate the spin cycle press the button until you reach the spin speed you
would like to set. To prevent damage to the fabrics, it is not possible to increase the speed over
that which is automatically suitable during the selection of the program.
It is possible to modify the spin speed without to pausing the machine.
Note:
The machine is fitted with a special electronic device, which prevents
the spin cycle should the load be unbalanced. This reduces the noise
and vibration in the machine and so prolongs the life of your machine.
6
3
120’ 90’
2
60
40
30
20
{
90
L
8
60’ 30’
{
5
{
{
4
{
“DIGITAL” Display
7
1
The display’s indicator system allows you to be constantly informed about the status of the machine:
1) WASH TEMPERATURE
When a programme is selected the relevant indicator will light up to show the wash temperature.
The Temperature button can be used to decrease or increase the temperature of your chosen
wash cycle. Each time the button is pressed, the new temperature level is shown on the
Wash Temperature Indicator.
If you want carry out a cold wash all the indicators must be off.
2) DOOR LIGHT
Once the START/PAUSE button has been pressed the light first flashes then stops flashing
and remains on until the end of the wash. 2 minutes after the end of the wash the light goes
off to show that the door can now be opened.
3) SPIN SPEED
Once the programme has been selected, the maximum spin speed allowed for that
programme appears on the display. Pressing the spin button will reduce the speed by 100
rpm each time the button is pressed. The minimum speed allowed is 400 rpm, or it is
possible to omit the spin by pressing the spin button repeatedly.
4) DELAY START LIGHT
This flashes when delay start has been set.
5) CYCLE DURATION
When a programme is selected the display automatically shows the cycle duration, which can vary,
depending on the options selected. Once the programme has started you will be kept informed
constantly of the time remaining to the end of the wash. If is selected the automatic washing/drying,
at the end of the wash phase, the drying time remaining to the end will be shown on the display.
13
8
3
120’ 90’
2
60
40
30
20
60’ 30’
{
90
{
6
{
{
5
{
4
7
1
6) KG MODE Indicator
Available on Cotton and Synthetic cycles, during the first 4 minutes of the cycle the indicator
lights and wash time will flash. This means the intelligent sensor is weighing the laundry and
will adjust the cycle time, water and electricity consumption accordingly.
7) WASH TIME
Once the programme has been selected the indicator light will automatically show the wash
time set for that programme. Selecting a different wash time the relevant indicator will light
up.
8) DRYING PROGRAMME INDICATORS
The indicators display the type of the drying programme:
The washer dryers incorporate an Automatic Sensor Drying function which takes the
guesswork out of setting the drying time. You simply select the degree of dryness you
require and the dryer automatically switches off when that level is reached. For added
flexibility there are 3 Sensor Drying levels to choose from:
= Extra dry programme
= Cupboard dry programme
= Iron dry programme
USEFUL TIPS:
Once the programme option has been selected, press the Start Pause button. The appliance
will then calculate the time to the end of the selected programme based upon a full dry load.
During the cycle the appliance will update the time to suit the actual load size and dampness
of the fabrics.
Timed programmes:
Alternatively you may select a pre-determined time for the drying cycle. The Timed Drying
programmes may be set to the following times:
120 minutes – 90 minutes – 60 minutes – 30 minutes:
Cool down phase
:
A 10 minute cool down phase occurs at the end of each drying cycle to ensure clothes are
not too hot to touch when the cycle finishes.
14
M
“WASH TIME” button
By selecting this button (active only on COTTON and MIXED FIBRES programmes) there is
a choice of 3 levels of wash intensity, depending on how much the fabrics are soiled.
Once the programme has been selected the indicator light will automatically show the wash
time set for that programme. Selecting a different wash time the relevant indicator will light
up.
PROGRAMME selector with "OFF" position
N
When the programme selector is turned
the display lights up to show the settings
for the programme selected.
N.B.switch
To
To switch
thethe
machine
machineoff,
off,turn
turn the
the
programme selector to the “OFF”
position.
Today,
most detergents
Press
the "Start/Pause"
button to start thehave
selectedbeen
cycle. improved to wash
efficiently
at
lower
temperatures,
therefore
haveonset
Once a programme is selected the programme selector remainswe
stationary
the the
selected
default
temperature
settings
of
each
programme
to
a
lower
programme till cycle ends.
level, saving electricity and reducing the carbon footprint of
Switch off the washing machine by turning the selector to "OFF".
your machine.
you can select an high temperature by pressing the
Note:
temperature
button.
The
programme
selector must be returned to the "OFF" position
please
refer
to the
programme
guide for
the maximum
at
the end
of each
cycle
or when starting
a subsequent
wash
temperature
to which
each programme
can be and
set. started.
cycle
prior to the
next programme
being selected
Press the "Start/Pause"
button
to start the selected cycle.
Buttons
indicator
light
O
Once a programme is selected the programme selector remains stationary on the selected
These
light up
relevant buttons are pressed.
programme
till when
cycle the
ends.
If an option is selected that is not compatible with the selected programme then the light on
Switch
off the
machine
by turning
the
button
firstwashing
flashes and
then goes
off. the selector to "OFF".
Note:
The programme selector must be returned to the "OFF" position
at the end of each cycle or when starting a subsequent wash
cycle prior to the next programme being selected and started.
O
Buttons indicator light
These light up when the relevant buttons are pressed.
If an option is selected that is not compatible with the selected programme then the light on
the button first flashes and then goes off.
15
TABLE OF PROGRAMMES
PROGRAMME
SELECTOR ON:
PROGRAM FOR:
Resistant fabrics
1)
Cotton, mixed
resistant,
Coloureds with Prewash
1)
WEIGHT RECOMMENDED
MAX
TEMP.
kg
°C
MAX TEMP.
°C
6
60°
Up to:
90°
6
40°
Up to:
60°
6
40°
Up to:
60°
3
40°
Up to:
60°
2
40°
Up to:
40°
1
40°
Up to:
40°
-
-
-
-
-
-
-
-
-
Hand wash
1
30°
Up to:
30°
Resistant fabrics
Mixed fabrics and synthetics
Rapid 30 minute
2
30°
Up to:
30°
6
20°
Up to:
20°
3
30°
Up to:
30°
3
-
-
4
-
-
Cotton, linen
Resistant fabrics
Mixed fabrics and synthetics
Cotton, mixed fabrics, synthetics
Very delicate fabrics
*
*
1)
*1)
**
*
“MACHINE WASHABLE”
woollens
Rinse
Fast spin
Drain only
Resistant fabrics
Mixed fabrics and synthetics
Cotton - Mixed
Mixed - Drying
*
*
*
*
*
Cotton - Drying
16
CHARGE DETERGENT
2
1
Please read these notes
Washing
Use the programme ** with the maximum wash time selected, maximum spin speed and a
temperature of 60°C.
Drying
First drying with 4kg (the load consist: pillowcases and hand-towels) selecting the cotton
drying programme (
) cupboard dry (
).
Second drying with 2kg (the load consist: 2 sheets and hand towels) selecting the cotton
drying programme (
) cupboard dry (
).
The spin speed may also be reduced, to match any guidelines suggested on the fabric label, or
for very delicate fabrics cancel the spin completely this option is available with a spin speed
button.
Pressing the wash temperature button makes it possible to wash at any temperature below
the maximum allowed.
* Programmes for automatic drying.
1) For the programmes shown you can adjust the duration and intensity of the wash using the
Wash Time button.
17
Programme selector
For the various types of fabrics and various degrees of dirt the washing machine has
different programme bands according to: wash cycle, temperature and lenght of cycle (see
table of washing cycle programmes on page 16).
COTTONS
The Cottons programme is designed for maximum washing and rinsing
efficiency. With spin cycles in between, the programme guarantees the
laundry is rinsed perfectly. The final spin cycle ensures laundry is spun dry
as much as possible up to the maximum speed.
The Cotton programme includes a Prewash cycle. This option is
particularly useful for really dirty loads and can be used independently of
the main wash programme. Additional detergent for the Prewash part of
the programme should be added to the first compartment of the soap
drawer labelled "1" (please refer to the section of this manual entitled
“Detergent”). We recommend you use only 20% of the quantity used for
the main wash programme.
MIXED AND SYNTHETIC FABRICS
The main wash and the rinse gives best results thanks to the rotation
rhythms of the drum and to the water levels.
A gentle spin will mean that the fabrics become less creased.
SPECIAL DELICATE FIBRES
This is a new wash cycle which alternates washing and soaking and is
particularly recommended for very delicate fabrics.
The wash cycle and rinses are carried out with high water levels to ensure
best results.
PROGRAMME
WOOLMARK
PROGRAMME
The special cycle enables to thoroughly wash garments without
damaging them. The cycle comprises of alternate periods of activity and
pauses. The programme has a maximum temperature of 40°C and
concludes with 3 rinses and a short spin.
SPECIAL “RINSE” PROGRAMME
This programme carries out three rinses with a intermediate spin (which
can be reduced or excluded by using the correct button). It can be used
for rinsing any type of fabric, eg. use after hand-washing.
18
SPECIAL “SPIN” PROGRAMME
Programme “SPIN” carries out a maximum spin (which can be reduced by
using the correct button).
DRAIN ONLY
This programme drains out the water.
SPECIAL “HAND WASH”
This washing machine also has a gentle Hand Wash programme cycle.
This programme allows a complete washing cycle for garments specified
as “Hand Wash only” on the fabric care label. The programme has a
temperature of 30°C and concludes with 3 rinses and a slow spin.
RAPID PROGRAMME
The 30 minute rapid programme allows a complete washing cycle to be
carried out in approximately 30 minutes, with up to a maximum load of
2 kg and a temperature of 40°C.
When selecting the "30 minute rapid" programme, please note that we
recommend you use only 20% of the recommended quantities shown on
the detergent pack.
“Eco 20°”
“ECO
MIX”PROGRAMME
PROGRAMME
This
programme,
allows
to wash2different
fabrics and colours
This innovative
is an exclusive
system
andyou
involves
great advantages
for the
together,
consumer:such as cottons, synthetics and mixed fabrics at only 20°C and
provides an excellent cleaning performance.
• to be able toonwash
togetheris different
type
fabrics (e.g.40°C
cotton
+ synthetic
Consumption
this program
about 40%
of aofconventional
cottons
wash.
etc…) FAST COLOUREDS;
• to wash with a considerable energy saving.
The "ECO MIX" programme has a temperature of 40°C and alternate
dynamic phases (the drum that turns) to static phases (fabrics in soak in
phase
of rest).
“SHIRT”
PROGRAMME
The
energy
consumption
the complete
cyclecycle
is only
W/h.
This programme
allows aforcomplete
washing
for 850
shirts.
The main wash and the rinse gives best results thanks to the rotation
Important:
rhythms of the drum and to the water levels.
• the first washing of new coloureds fabrics must be done separately;
programme
has amix
maximum
temperature
of 40°Cfabrics.
and concludes with
•The
in every
case, never
NON-FAST
COLOUREDS
3 rinses and a short spin.
19
DRYING
Note: Dispensers used for concentrated powders and liquid
detergents must be removed from the drum before commencing the
tumble drying programmes.
The drum changes direction during the drying cycle to prevent the laundry
from tangling and hence produce even drying. Cool air is used during the
last ten minutes of the drying cycle to minimise creasing.
LOW HEAT
Low temperature drying programme for synthetics and mixed fibres,
always refer to the care label.
HIGH HEAT
High temperature drying programme for Cottons and linen items, always
refer to the care label
Automatic Variable Capacity
The washing machine is fitted with an automatic reduction in consumption system (known as
Automatic Variable Capacity).
This system enables the machine to use the amount of water needed to wash and rinse the
laundry in relation to the particular load.
This results in a reduction in the amount of water used and electricity needed to heat it to the
minimum required, without in any way compromising the washing and rinsing performance.
In fact the amount of water and electricity used will always be appropriate for the amount of
washing.
The washing machine therefore ensures you achieve excellent washing results whilst
respecting the environment and saving you money.
20
Detergent drawer
P
The detergent drawer is split into 3 compartments:
- the compartment labelled "1" is for prewash detergent;
- the compartment labelled " " is for special additives,
fabric softeners, fragrances, starch, brighteners etc;
- the compartment labelled "2" is for main wash
detergent.
If liquid detergents are used, please insert the special
container supplied into the compartment marked “2” in the
detergent drawer. This ensures that the liquid detergent
NOTE:
enters
the drum at the right stage of the wash cycle.
Some Detergents are Difficult to
This special container must be inserted into the
utilise. Ensure
an drawer,
in drum
compartment
marked "2" intotheuse
detergent
also
when
you
wish
to
use
the
"RINSE"
programme
as
dispenser if recommended by
BLEACHING cycle.
the detergent Manufacturer.
NOTE:
Note:
only put liquid
products
Some Detergents
are Difficult
to in the compartment
labelled
“
The
utilise. Ensure
to”.use
anmachine
in drum is programmed to
automatically
take up additives
dispenser if recommended
by during the final rinse
stage
for all wash
cycles.
the detergent
Manufacturer.
Note: only put liquid products in the compartment
labelled “
”. The machine is programmed to
automatically take up additives during the final rinse
stage for all wash cycles.
21
Detergents, washing aids and amounts to use
Choice of detergent
General purpose detergents
-
-
Powder detergents, for a thorough wash, with bleaching agent, particularly suitable for
use in hot wash programmes (60°C and over), for heavily soiled and stained laundry.
Liquid detergents, particularly suitable for grease stains, such as greasy skin marks,
cosmetics and oil.
These detergents are not suitable for washing stained laundry, as they do not contain
bleach.
Biological detergents, not all the products available give a really thorough wash.
Additional laundry aids
-
Water softener, means less detergent can be used where water hardness is classed as
hard to very hard.
Prewash substances, for the programmed treatment of stains prior to the main wash.
Using them means the subsequent wash can be at a low temperature or with bleach-free
detergents.
Fabric softener, prevents static build-up in synthetic fabrics and softens fabrics.
If you own a tumble dryer, clothes are softened even without the use of a fabric softener.
Do not put solvents in the washing machine!
Keep detergents and other laundry products out of children’s reach.
Before pouring in the detergent check that there are no foreign bodies in the detergent
drawer.
Dosage details are usually shown on the detergent packaging. Follow those instructions.
22
Dosages
Only use detergents which are suitable for use in a washing machine.
You will obtain the best results from your wash with the minimum use of chemical products
and the best care for your laundry if you take into consideration the degree of soiling as well
as the type of detergent to choose.
The amount of detergent to use depends on:
- water hardness: depending on the hardness of the water and the type of detergent used, it
is possible to reduce the amount of detergent.
- the degree of soiling: it is possible to reduce the amount of detergent used depending on
the degree of soiling.
- amount of laundry: it is possible to reduce the amount of detergent when washing only a
small amount of laundry.
Dosage for powder detergent
For normal and low concentration detergents: for normally soiled laundry choose a
programme without prewash.
Put the detergent in compartment “2” of the drawer.
For heavily soiled laundry, choose a programme with prewash.
Put 1/4 of the detergent in compartment “1”, 3/4 in compartment “2” of the drawer.
When using water softeners, first put in the detergent, then add the softener to compartment “2”.
For highly concentrated detergents not in single dose format, follow what is shown on pack
exactly as regards type and amount of dosage.
To avoid the difficulty of checking if the detergent has been taken up, use the dosage aids
provided in the detergent packaging.
Liquid detergent dosage
Liquid detergents may be used in accordance with the instructions on the relevant
packaging, for all programmes without prewash, by using the special container which is
placed in the drum or, for those models that have it, in the special insert for liquid detergents.
Recommendations on the use of detergent at various temperatures
When washing heavily soiled whites, we recommend using cotton programs of 60°C or above and a
normal washing powder (heavy duty) that contains bleaching agents that at medium/high temperatures
provide excellent results. For washes between 40°C and 60°C the type of detergent used needs to be
appropriate for the type of fabric and level of soiling. Normal powders are suitable for “white” or colour fast
fabrics with high soiling, while liquid detergents or “colour protecting” powders are suitable for coloured
fabrics with light levels of soiling. For washing at temperatures below 40°C we recommend the use of
liquid detergents or detergents speciÀcally labeled as suitable for low temperature washing. For washing
wool or silk, only use detergents speciÀcally formulated for these fabrics. For dosage amounts please
follow the instructions on the detergent package label.
23
Useful advice for users
Tips on using your domestic appliance in the most environmentally-friendly and economical
way.
Do a full load in your washing machine
To prevent any possible waste of energy, water or detergent we recommend that you put a
full load in your washing machine, not exceed the recommended maximum load size.
About 50% energy saving can be made with one full load compared to two half load washes.
When is prewashing really needed?
Only with particularly dirty loads!
Energy savings about 5 to 15% are made by not selecting the prewash option for normal
soiled laundry.
Which wash temperature should you choose?
Using stain removers before machine washing reduces the need to wash at temperatures
over 60°C.
Energy savings about 50% can be made by using a 60°C wash temperature rather than
90°C.
Before using a drying programme...
SAVE energy and time by selecting a high spin speed to reduce the water content in laundry
before using a drying programme.
24
Main wash
Sorting the laundry
-
It is recommended you wash only items which are machine washable with water and
detergent and not dry-clean items.
-
If you need to wash rugs, bedspreads or other heavy items, it is best not to spin them.
-
Sort the laundry according to fabric type, degree of soiling and wash temperature: Always
follow the wash care advice on the garment label for the most suitable care and
treatment of the laundry
Laundry for hot wash
Coloured, easy-care materials
Delicates and wool
Wash by hand
Items labelled with the following symbol are not suitable for machine washing:
Dry clean
For very delicate items, such as net curtains, underwear, tights etc., you are advised to
use a laundry net or wash bag.
Woollen items must be labelled with the "Pure New Wool" symbol to be washed in the
machine and must also be labelled "non-matting" or "machine washable".
Colour often leaks from new coloured items.
This can then colour other lighter items being washed.
We therefore recommend that coloured items should be washed for the first time
separately.
For future washes, colourfast items can only be washed with whites up to 40°C.
-
Warning: when sorting laundry
-
check there are no metal objects in the laundry
(such as paper clips, safety pins, pins, coins
etc...);
button up pillowcases, fasten zips, hook & eye
fasteners, belts and long dressing gown cords;
remove curtain hooks;
pay close attention to the labels on items
if you notice stubborn stains whilst sorting the
laundry, remove them using a special detergent or
a special stain remover.
- We recommend that you do not do a full load of towelling items only as these become too
heavy since they absorb a lot of water.
25
The correct way to wash
Preparing the laundry
A) Select the laundry.
Loading the laundry
B) Open the porthole.
C) Put the laundry in the washing machine.
Close the porthole again, ensuring that no items
ms ofof
laundry are obstructing the lock.
Putting detergent in machine
dosi
D) Open the drawer, choose the detergent and put
ut inin
gli
di
the correct amount, according to the manufacturer’s
rer’s
instructions and the advice on page 22.
liari
Add any other laundry aids (see page 22). Closee the
the
drawer again.
ggio
Selecting the wash programme
Refer to the programme guide or the programme descriptions on the machine to select the
most suitable programme.
Turning the selector knob, the required programme is activated.
Adjust the wash temperature if necessary.
Press additional function buttons (if required).
Check that the tap is turned on and that the discharge hose is positioned correctly.
Press the "Start/Pause" button.
When the "Start/Pause" button is pressed the machine sets the working sequence in motion.
The programme carries out with the programme selector stationary on the selected
programme till cycle ends.
Warning: If there is any break in the power supply while the machine is operating, a special
memory stores the selected programme and, when the power is restored, it continues where
it left off.
When the programme is finished
The word “End” will appear on the display.
Wait for the door lock to be released (about 2 minutes after the programme has finished).
The "Door Security" indicator light will go out.
Switch off the machine by turning the programme selector on the “OFF” position. Open the
door and remove the laundry. Turn off the tap.
26
DRYING
DON’T DRY GARMENTS MADE FROM FOAM RUBBER
OR FLAMMABLE MATERIALS.
IMPORTANT:
THIS DRYER CAN ONLY BE USED FOR LAUNDRY
WHICH HAS BEEN WASHED AND SPIN DRIED.
WARNING:
Indications given are general, therefore some practice is needed for the best drying results.
We recommend setting a lower drying time than indicated, when first using, so as to
establish the degree of dryness required. We recommend not to dry fabrics that fray easily,
such as rugs or garments with a deep pile, to avoid air duct clogging.
The water is then conveyed to the drain circuit, wich is sealed and therefore, no steam can
be released outside.
Important
Never open the door after the drying cycle has begun wait until the cool down period provided for by the
cycle
.
Only dry pre-spun laundry
The washer/dryer can perform two types of drying:
1 Cotton, terry towelling, linen, hemp fabrics, etc...
Advisory note
symbol on programme dial.
During drying phase the drum will accelerate to a higher speed to distribute the load
and to optimize the drying performance
2 Mixed fabrics (synthetics/cotton), synthetic fabrics
27
symbol on programme dial.
Drying cycle
The correct way to dry:
- Open door.
- Fill with up to 4 kg - in case of large items (e.g. sheets) or very absorbent items (e.g.
towels or jeans), it is a good idea to reduce the load.
- Close door.
- Turn programme dial to
cotton.
Select the degree of dryness that you require.
This ranges from Extra Dry (
) for bath towels and bathrobes, through Cupboard Dry
(
) for items that will be put away without ironing, to iron dry (
) that leaves the
laundry suitable for ironing.
If you wish to select a timed drying cycle, press the “drying selection” button until the
required time indicator lights up.
DOUBLE-SKIN DOOR
The appliance door is fitted with a protective shield to prevent
contact with the glass door which can reach high temperatures,
during the drying cycle.
It should not be necessary to remove the shield from the machine
during the normal course of use.
Warning: do not touch door for any reason.
Warning:
do not dry woollen garments or articles with special padding,
(e.g. quilts, quilted anoraks, etc.).
Delicate fabrics if garments are drip/dry, load less items ao as to
prevent creasing.
Press the Start button.
The drying phase will begin with the programme dial fixed on the
the end of drying.
symbol until
The drying programme indicator will be on until the cool down phase will begin and the
indicator “
” will go on.
When the programme is finished
The word “End” will appear on the display.
Wait for the door lock to be released (about 2 minutes after the programme has finished).
The "Door Security" indicator light will go out.
Switch off the machine by turning the programme selector on the “OFF” position. Open the
door and remove the laundry. Turn off the tap.
28
Automatic washing/drying cycle
Warning: only a maximum 4 kg of dry laundry can be loaded
otherwise the dried laundry will be not satisfactory.
WASHING:
Open the drawer, choose the detergent and put in the correct amount.
Refer to the list of washing programmes according to fabrics to be washed (e.g. very dirty
cotton) and without pressing Start button, prepare wash as described:
Turning the selector knob, the required programme is activated.
The display will show the settings for the programme selected.
Adjust the wash temperature if necessary.
Press the option buttons (if required)
Check that the tap is turned on and that the discharge hose is positioned correctly.
DRYING:
Select the degree of dryness that you require.
This ranges from Extra Dry (
) for bath towels and bathrobes, through Cupboard Dry
(
) for items that will be put away without ironing, to iron dry (
) that leaves the laundry
suitable for ironing.
If you wish to select a timed drying cycle, press the “drying selection” button until
the required time indicator lights up.
Press the "Start/Pause" button.
When the "Start/Pause" button is pressed the machine sets the working sequence in motion.
The programme carries out with the programme selector stationary on the selected
programme till cycle ends.
At the end of the wash phase the display will shown the drying time remaining.
The washer-dryer will then complete the entire drying programme.
The drying programme indicator will be on until the cool down phase will begin and the
indicator “
” will go on.
When the programme is finished
The word “End” will appear on the display.
Wait for the door lock to be released (about 2 minutes after the programme has finished).
The "Door Security" indicator light will go out.
Switch off the machine by turning the programme selector on the “OFF” position. Open the
door and remove the laundry. Turn off the tap.
29
Table of drying times (in minutes):
PROGRAMME
Extra
Cupboard
Iron
COTTON
MIXED
Min 1 Kg
Max 4 Kg
Min 1 Kg
Max 3 Kg
from 30’
from 30’
from 30’
to 230’
to 220’
to 170’
from 30’
from 30’
from 30’
to 170’
to 150’
to 80’
The time remaining shown on the digital display will show the time remaining for a
full load. However, this will be corrected during the cycle once the appliance
assesses the weight and dampness of the laundry.
30
Cleaning and routine maintenance
Do not use alcohol-based scourers and / or thinners on the outside of your washing machine,
just a wipe with a damp cloth will suffice. The washing machine needs very little maintenance:
- Cleaning the drawer compartments.
- Cleaning the filter.
- Cleaning the door glass.
Cleaning the drawer compartments
Even if it is not strictly necessary, it is good to clean the
compartments for bleaching detergents and additives
occasionally.
A) To do this you just need to pull them out firmly, but
without forcing them.
B) Clean everything in the compartment under running
water.
C) Put everything back in its proper place.
Cleaning the filter
The washing machine is fitted with a special filter for
handling large deposits which could block the discharge
hose (coins, buttons etc.) and which can, therefore, be
easily retrieved.
We recommend that the filter be cleaned at least
once a month.
The cleaning operation is as follows:
1) Open the flap
2) Only available on certain models:
Pull out the corrugated hose, remove the stopper and
drain the water into a container.
3) Before removing the filter, place an absorbent towel
below the filter cap to collect the small amount of
water likely to be inside the pump
4) Turn the filter anti-clockwise until it stops in the
vertical position.
Remove and clean.
5) After cleaning, replace by turning the notch on the
end of the filter clockwise. Then follow all procedures
described above in reverse order.
31
Attention: if the filter needs cleaning while there is
washing still in the drum, follow the instructions on the
following page to empty the water. This will prevent
excessive loss of water via the filter.
Cleaning the door glass
Regularly clean the door glass with a damp cloth. A build
up of soiling and
residues from the water may result in water leaking from
the door.
Do not use abrasive cleaners as they can scratch the
surface.
Transporting the appliance or long
periods when appliance is not in
use
If the appliance is being transported or is out of use for
long periods in unheated places, all remaining water
must be completely removed from the hoses.
Ensure mains power is off, then unclip the hose and
point it downwards into a basin until all the water has
emptied out.
When finished, repeat the operation in the reverse order.
32
Investigating malfunctions
What might be the cause of…
Defects you can remedy yourself
MALFUNCTION CAUSE
REMEDY
1. Does not work on any
programme
Plug not in socket.
Not switched on.
Power failure.
Fuse blown.
Door open.
Plug it in.
Switch on.
Check.
Check.
Close door.
2. Does not fill with water
See cause 1.
Tap turned off.
Programme selector not correctly positioned.
Fill hoses are kinked
Check.
Turn on tap.
Position programme selector correctly.
Straighten fill hoses
3. Water does not drain away
Kink in discharge hose.
House drain is blocked
Foreig bodies in filter
Straighten discharge hose.
Clean drain
Examine filter
4. Water on floor around the
washing machine
Leaking gasket between tap and water inlet
hose.
House drain is blocked
Soap drawer blocked with soap residues
Replace gasket and tighten hose and tap
well.
Clean drain
Clean soap drawer
5. Does not spin
Water has not yet drained away.
"No spin" selected (certain models only).
Wait a few minutes for machine to empty.
Reset button or turn "no spin" knob.
6. Machine vibrates a lot
during spin
Washing machine not completely level.
Transit brackets not removed yet.
Load not distributed evenly.
Adjust the special adjustable feet.
Remove transit brackets.
Rearrange the laundry evenly.
7. Door will not open
Two minutes have not elapsed since the
programme finished.
Wait two minutes.
8. Display reads error
0, 1, 5, 7, 8, 9
–
9. Display reads error 2
No water fill.
Check water supplies are on.
10. Display reads error 3
No pump out.
Check drain is clear.
Check drain hose is not kinked.
11. Display reads
error 4
Machine overfilled with water.
Turn off water supply to machine.
Call service.
Call service.
During drying phase the drum will accelerate to a higher speed to distribute the load
and to optimize the drying performance
The machine makes a
different noise when
spinning! This is because it
has a brush motor for better
performance.
Only a small level of water can be
seen in the drum! This is because
new machines do not use much
water, yet achieve the same standard
of washing and rinsing.
33
Note:
The use of environmentally-friendly, phosphate-free detergents can have the following effects:
- waste water from rinsing may be cloudier because of the presence of zeolites held in
suspension, without the rinse performance being adversely affected;
- presence of white powder (zeolites) on laundry after washing, which is not absorbed by
the fabric and does not alter the colour of the fabric.
- The presence of foam in the final rinsing water is not necessarily an indication of poor
rinsing.
- Anionic surfactants used in washing detergent formulae often prove to be difficult to
remove from the laundry itself and, even in small quantities, can still cause considerable
foam production.
- Carrying out more rinse cycles does not serve any purpose in such cases.
34
Fig. 2
Technical data
6 kg
4 kg
0,05 ÷ 0,8 MPa
Max. load of dry laundry
Max. load of dry laundry for drying
Water pressure
Measurements
Width
Depth
Height
60 cm
44 cm
85 cm
Note: For specifications regarding electrical data, see the data panel on the front of the washing
machine (porthole area) - as shown in diagram above.
35
SETTING UP + INSTALLATION
1
Remove the polystyrene base and place the machine near
its permanent position (diagram 1).
Carefully cut through the hose retaining clip at the rear of
the appliance (diagram 2).
Remove the 3 fixing screws marked (A) and remove the 3
spacers marked (B) (diagram 3).
2
Remove the screw (C).
A spacer will fall inside the machine.
By tilting the machine, remove the above mentioned spacer.
Cover the 4 holes using the caps provided in the instruction
booklet pack (diagram 4).
3
4
WARNING:
WARNING:
DO NOT
NOT LEAVE
LEAVE THE
THE PACKAGING
PACKAGING
WITHIN
REACH
OF
CHILDREN
AS
IT
IS
POTENTIAL
DO
PACKAGING WITHIN
WITHIN REACH
REACH OF
OFCHILDREN
CHILDRENAS
ASIT
ITIS
ISAAAPOTENTIAL
POTENTIAL
SOURCE
OF
DANGER.
SOURCE OF DANGER.
Apply the insulation sheet of corrugated material to the base as shown.
Apply
the1 insulation
insulation sheet
sheet of
of corrugated
corrugated
material to the base
Apply
the
Type 2 material to the base
Type
as
shown.
as shown.
Use the
the 44 feet
feet to
to level
level the
the machine
machine with
with the
the floor:
floor:
Use
a)
Turn
the
nut
clockwise
to
release
the
screw
adjuster on
on the
the foot.
foot.
a) Turn the nut clockwise to release the screw adjuster
b)
Rotate
the
foot
to
raise
or
lower
it
until
it
stands
firmly
on
the
b) Rotate the foot to raise or lower it until it stands firmly on the
ground.
Use
the 4 feet to level the machine with the floor:
ground.
c) Lock
Lock the
the foot
footclockwise
in position
positiontoby
byrelease
turningthe
thescrew
nut adjuster on the foot.
a)
Turn
nut
c)
in
turning
the
nut
anti-clockwise
until
it
comes
up
against
the
bottom firmly
of the
the on
machine.
b) Rotate the foot
orup
lower
it until
stands
the
anti-clockwise
untiltoit raise
comes
against
theit bottom
of
machine.
ground.
c) Lock the foot in position by turning the nut
anti-clockwise until it comes up against the bottom of the machine.
36
A
A
A
B
B
B
C
C
C
Note: we recommend you keep the screws to
immobilise the machine for future transit.
The Manufacturers will not be responsible for any
possible damage to the machine caused by not
following the rules relating to releasing the mechanism.
The user is responsible for all costs of installation.
Water connection
The appliance must be connected to the water mains using new
hose-sets.
The old hose-sets should not be re-used.
The machine has an inlet hose with 3/4" B.S.P threaded end
connection to attach between the threaded connector on the
appliance and the cold water supply.
This machine only uses cold water, therefore
only one hose is needed to connect to the cold
water supply. Do not connect to the hot supply.
Cold fill is an energy efficient system. Only the
water required for the washing is heated.There
is no loss of heat in the pipeline from a hot
water tank or boiler to the machine.
max 100 cm
min 4 cm
37
+2,6 mt max
min 50 cm
max 85 cm
Note: it is advisable to turn off the tap after each wash
to isolate the washing machine from the water supply.
The appliance must not be installed behind a lockable door, a sliding door or a door with a
hinge on the opposite side to that of the washer dryer.
For the washing machine to function properly the terminal end of the discharge hose (mouth)
must be at a minimum of 50 cm and a maximum of 85 cm from the ground.
ELECTRICAL CONNECTIONS
After installation, the appliance must be positioned so that the plug is accessible.
If the plug we supply does not fit
CUT IT OFF AND DESTROY IT!
You can’t use it on other appliances, and the exposed wires could be dangerous if plugged in.
To fit a replacement plug, proceed as follows:
Connect
to the terminal in the plug
green and yellow wire
marked with the letter E,
OR marked
with the symbol,
OR coloured green,
OR coloured green and yellow.
blue wire
marked N
OR coloured black.
brown wire
marked L
OR coloured red.
WARNING
This appliance must be earthed
Fuses and plugs
This appliance should be used only on a socket with a minimum rating of 13 Amp.
Our ready-fitted plug is already equipped with a 13 amp fuse which is BS 1362 ASTA
approved. Any replacement should be exactly the same.
If the fuse cover is lost, do not use the plug until it is replaced. A correct replacement fuse
cover (obtainable from your local retailer) must be the same colour as shown or named on
the insert on the base of the plug.
38
The manufacturer declines all responsibility in the event of any printing mistakes in
this booklet. The manufacturer also reserves the right to make appropriate
modifications to its products without changing the essential characteristics.
This appliance is marked according to the European directive 2012/19/EU on Waste Electrical
and Electronic Equipment (WEEE). WEEE contains both polluting substances (which can cause
negative consequences for the environment) and basic components (which can be re-used). It is
important to have WEEE subjected to specific treatments, in order to remove and dispose properly
all pollutants, and recover and recycle all materials.
Individuals can play an important role in ensuring that WEEE does not become an environmental
issue; it is essential to follow some basic rules:
- WEEE should not be treated as household waste;
- WEEE should be handed over to the relevant collection points managed by the municipality or by
registered companies. In many countries, for large WEEE, home collection could be present.
In many countries, when you buy a new appliance, the old one may be returned to the retailer who
has to collect it free of charge on a one-to-one basis, as long as the equipment is of equivalent type
and has the same functions as the supplied equipment.
15.11 - 41041463 - Canon Italia - Business Services Channel
EN
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising