Terzismo | HJA 8704 | Terzismo HJA 8704 User manual

Terzismo HJA 8704 User manual
Integrated Washer Dryer
HJA 8704
Installation & Operating Instructions
Introduction
Please read these instructions for use carefully and all other information
enclosed with the washing machine.
Keep all documentation in a safe place for future reference or for any future
owners.
Note: this machine is solely for domestic use.
Notes on disposal
All packaging material used is environmentally-friendly and recyclable. Please help dispose of
the packaging via environmentally-friendly means.
Your supplier or local council will be able to give you
details of current means of disposal.
Contents
Page
Introduction
General delivery notes
Safety notes
Quick start
Description of controls
Programme Table
Programme selector
Detergent drawer
Detergents, washing aids and amounts to use
Useful advice for the user
The main wash
Drying
Automatic washing/drying cycle
Drying cycle
Cleaning and routine maintenance
Investigating malfunctions
Technical data
Setting up + installation
2
4
4
5
6
14
16
20
21
23
24
26
27
28
29
30
32
33
Valuable materials can be salvaged from an old appliance via scrap reprocessing.
Note: pull out the mains plug from any old appliance.
Cut the power cable and dispose of it, together with the
plug.
BEFORE SWITCHING ON THE APPLIANCE MAKE SURE
IT IS CORRECTLY INSTALLED AND THAT THE TRANSIT
SCREWS ARE REMOVED AS SHOWN IN PAGE 33.
When disposing of an old washing machine, please ensure that the door lock is rendered
inoperable to prevent children shutting themselves in the appliance.
2
3
General delivery notes
Please check that the following items are delivered with the appliance:
- Instruction manual
- Certificate of guarantee
- Inlet hose
Check that no damage has occurred during transit, and if so, call your nearest Authorised
Technical Support Service agent.
L) N.B!
If the appliance is installed on a carpeted floor ensure that the ventilation holes on the
base of the appliance are not obstructed.
M) If the appliance is not running properly or breaks down, switch it off, turn off the tap and do
not tamper with the appliance.
Consult only the Authorised Technical Support Service for possible repair and ask them to
use original spare parts.
Failure to comply with the above can compromise the safety of the appliance.
N) If the appliance’s power cable should ever need replacing, consult the Authorised
Technical Support Service
Quick start
Safety notes
Note:
for cleaning or maintenance of the washing machine.
A) Pull out the plug
B) Turn off the tap
C) Do not touch the appliance when hands or feet are wet or damp. Do not use the appliance
with bare feet.
D) The use of adapters, multiple connectors and/or extensions is not recommended.
Washing
-
DRYING
If you would like the drying cycle to begin automatically after
washing, select the programme required using the Drying
Programme Selector knob.
Otherwise it is possible to finish the wash and then decide on the
drying programme and load.
Note:
water temperature can reach 90°C during the wash cycle.
E) Check there is no water left in the drum before opening the door.
F) This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
G) Do not pull the power cable or the appliance itself to remove the plug from the socket.
H) The appliance must not be exposed to weather conditions (rain, direct sun, etc...)
I) When moving the appliance never lift it by the controls or by the detergent drawer.
When in transit never rest the door against the trolley or transport the appliance without
the polystyrene base.
Open the door by using the button “A” (Fig. 1, page 6)
Select laundry and put it in the machine
Close the door
Put detergent in the compartments as indicated in the programme guide in this instruction
manual
Select programme
Wait for the “STOP” indicator light to flash
Press additional function buttons (if required)
-
Press the “Start/Pause” button (page 7)
After few seconds the appliance starts working.
After washing
The indicator light “STOP” will go on.
Wait for the door lock to be released
(about 2 minutes after the programme has finished).
The “Door Security” indicator light will go out.
Switch off the washing machine by turning the selector
to “OFF” position.
Open the door and remove the laundry.
Ensure that the machine is correctly installed in line with the instructions found on page 33.
4
5
Description of controls
A
Door open button
Important:
A special safety device prevents the door from opening at the end of the wash/spin cycle. At
the end of the spin phase wait up to 2 minutes before opening the door.
Fig. 1
LBM G O N
Q
DOOR SECURITY indicator light
B
The “Door Security” indicator light is illuminated when the door is fully closed and the machine is ON.
When "Start/Pause" is pressed on the machine with the door closed the indicator will flash
momentarily and then illuminate.
P
If the door is not closed the indicator will continue to flash.
R
I H F E DC
A special safety device prevents the door from being opened immediately after the end of the cycle.
Wait for 2 minutes after the wash cycle has finished and the “Door Security” light has gone out
before opening the door. At the end of the cycle turn the programme selector to "OFF" .
A
C
START/PAUSE button
Door open button
Door locked indicator light
Start button
Crease Guard button
Cold Wash button
Drying selection button
Drying programme indicators
Extra Rinse button
Super Rapid button
Start Delay button
“Time to end” and “Start Delay” indicator light
Spin Speed button
Spin Speed indicator light
Buttons indicator light
Timer knob for wash programmes with OFF position
Detergent drawer
6
A
B
C
D
E
F
G
H
I
L
M
N
O
P
Q
R
When a programme is selected, wait for the “STOP” indicator
light to flash before pressing the "Start/Pause" button.
Press to start the selected cycle (according to the selected cycle one indicator light will go on) .
NOTE: When the "Start/Pause" button has been pressed,
the appliance can take a few seconds before it starts
working.
Changing the settings after the programme has started (PAUSE)
The programme may be paused at any time during the wash cycle by holding down the
"Start/Pause" button for about two seconds. When the machine is in the paused mode, the
indicator light "Time to end" and option buttons will flash.
To restart the programme, press the "Start/Pause" button once again.
If you wish to add or remove items during washing, wait 2 minutes until the safety device
unlocks the door.
When you have carried out the manoeuvre, close the door, press "Start/Pause" button and
the appliance will continue working where it left off.
CANCELLING THE PROGRAMME
To cancel the programme, set the selector to the OFF position.
Select a different programme.
Re-set the programme selector to the OFF position.
7
The option buttons should be selected before pressing
the "Start/Pause" button.
D
CREASE GUARD button
Press the button to select or deselect this function.
The Crease Guard function minimizes creases as much as possible with a uniquely designed
anti-crease system that is tailored to specific fabrics.
MIXED FABRICS - the water is gradually cooled throughout the final two rinses with no
spinning and then a delicate spin assures the maximum relaxation of the fabrics.
DELICATE FABRICS – final two rinses with no spinning and then the fabrics are left in water
until it is time to unload. When you are ready to unload, press the "Crease Guard" button –
this will drain.
WOOLLENS/SILK – after the final rinse the fabrics are left in water until it is time to unload
and the button indicator blinking.
When you are ready to unload, press the "Crease Guard" button, this will drain and spin
ready for emptying.
If you do not want to spin the clothes and activate drain only:
“DRYING SELECTION” button
F
With the programme selector not in the OFF position, press the button to select the required
drying programme; an indicator will light to display the drying result selected each time you
press the button.
To cancel the selection before the start of a drying programme, press the button repeatedly
until the indicators go out or return the programme selector to the OFF position.
To cancel the cycle during the drying phase, hold the button down for 2 seconds until the
cooling indicator lights up; given the high temperature inside the drum, we recommend that
you allow the dryer to complete the cool down period before returning the programme
selector to the OFF position and removing the laundry.
USEFUL TIPS:
Do not dry unwashed items in the washer dryer.
Items that have been soiled with substances such as cooking oil, acetone, alcohol, petrol,
kerosene, spot removers, turpentine, waxes and wax removers should be washed in hot
water with an extra amount of detergent before being dried in the washer dryer.
Items such as foam rubber (latex foam), shower caps, waterproof textiles, rubber backed
articles and clothes or pillows fitted with foam rubber pads should not be dried in the washer
dryer.
Fabric softeners, or similar products, should be used as specified by the fabric softener
instructions.
- Turn the programme selector to the "OFF" position;
- Select programme drain only
The final part of a washer dryer cycle occurs without heat (cool down cycle) to ensure that
the items are left at a temperature that ensures that the items will not be damaged.
;
- Switch on the appliance again by pressing the "Start/Pause" button.
WARNING:
Never stop a washer dryer before the end of the drying cycle unless all items are
quickly removed and spread out so that the heat is dissipated.
E
COLD WASH BUTTON
By pressing this button it is possible to transform every programme into a cold washing one,
without modifying other characteristics (water level, times, rythmes, etc...).
Curtains, small carpets, man made delicate fabrics, non coulor fast garments can be safely
washed thanks to this new device.
8
9
G
Drying programme indicators
The indicators display the type of programme and/or drying time:
Automatic Programmes: By selecting one of these 3 automatic programmes, the washerdryer will calculate the time needed for drying and the residual dampness required, according
to the load and drying type selected.
After pressing the START button, one of the indicators will light to display the drying time
remaining.
H
EXTRA RINSE BUTTON
Thanks to the new electronic system selecting the ‘Extra Rinse Button’ will enable the
machine to perform a special rinse cycle. This function is ideal for people with sensitive skin
as it removes more of the detergent from the washing. It is advisable to use this function for
very dirty loads where extra detergent has been used and for washing towelling items
whose fibres have a tendency to retain detergent.
This option is only available on the “ALL” programme in the SPECIAL programmes options.
= Extra dry drying programme (recommended for towels, bathrobes and bulky
loads)
= Cupboard dry drying programme
= Iron dry drying programme
USEFUL TIPS:
The 30 minute drying programme is recommended for small loads (less than 1 kg) or slightly
damp loads.
Your washer-dryer ends the cycle automatically when it reaches the drying level selected.
For the correct operation of the appliance, it is preferable not to interrupt the drying phase
unless it is really necessary.
I
SUPER RAPID button
Pressing this button reduces the time of the wash programme by a maximum of 50 minutes
depending on the programme and the temperature selected. The "Super Rapid" button can
be used for washing loads of 1 to 7 kg. This option may only be utilised on COTTONS and
SYNTHETICS programmes.
In this case care must be taken as both the machine and the clothes may be very hot as the
cooling down part of the drying cycle will not have been carried out.
For correct operation it is advisable to allow the machine to carry out the cooling down cycle
.
Timed programmes:
120 minutes – 90 minutes – 60 minutes – 30 minutes:
Dual function indicators:
If one of the 3 automatic drying programmes is selected, the indicators display the drying
time remaining
They may be used to select timed drying programmes.
:
Cool down phase
Switched on during the final cool down period, in the last 10 minutes of each drying phase.
TABLE OF DRYING TIMES (IN MINUTES):
PROGRAMME
Extra
Cupboard
Iron
COTTON
MIXED
Min 1 Kg
Max 5 Kg
Min 1 Kg
Max 3,5 Kg
from 30’
from 30’
from 30’
to 230’
to 220’
to 170’
from 30’
from 30’
from 30’
to 170’
to 150’
to 80’
10
L
START DELAY BUTTON
Appliance start time can be set with this button, delaying the start by 3, 6 or 9 hours.
Proceed as follow to set a delayed start:
Select a programme (“STOP” indicator light blinks)
Press Start Delay button (each time the button is pressed the start will be delayed by 3, 6 or
9 hours respectively and the corresponding light will blink).
Press START to commence the Start Delay operation (the indicator light associated with the
selected Start Delay time stops blinking and remains ON).
At the end of the required time delay the programme will start.
To cancel the Start Delay function:
press the Start Delay button until the indicator lights will be off (The STOP light blinks) and
the programme can be started manually using the START button or switch off the appliance
by turning the programme selector to off position.
11
M
TIME TO END indicator light
In order to manage your time better, this washing machine features an indicator light system
that keeps you constantly informed on the remaining cycle time.
P
Buttons indicator light
The indicator light around the option buttons will light when specific options are selected.
If you select an option button that is not compatible with the programme required the
button light will not illuminate.
Indicator light 90:
Remaining time above 60 minutes.
PROGRAMME selector with "OFF" position
Indicator light 60:
Remaining time less than 60 minutes.
Indicator light 30:
Remaining time less than 30 minutes.
Indicator light 15:
Remaining time less than 15 minutes.
Indicator light STOP:
End of the programme.
N
SPIN SPEED button
The spin cycle is very important to remove as much water as possible from the laundry without
damaging the fabrics. You can adjust the spin speed of the machine to suit your needs.
By pressing this button, it is possible to reduce the maximum speed, and if you wish, the spin cycle
can be cancelled.
To reactivate the spin cycle press the button until you reach the spin speed you would like to set.
To prevent damage to the fabrics, it is not possible to increase the speed over that which is
automatically suitable during the selection of the program.
Rotates in both directions.
The machine is turned on by
selecting a programme via the
programme selector. This status
will be indicated by the "STOP"
indicator light flashing, this light
will continue to flash until the
machine has started or the
machine is returned to the
"OFF" position.
Press the "Start/Pause" button to start the selected cycle.
Once a programme is selected the programme selector remains stationary on the selected
programme till cycle ends.
It is possible to modify the spin speed without to pausing the machine.
Note:
The machine is fitted with a special electronic device, which
prevents the spin cycle should the load be unbalanced.
This reduces the noise and vibration in the machine and so
prolongs the life of your machine.
Switch off the washing machine by turning the selector to "OFF".
Note:
The programme selector must be returned to the "OFF" position
at the end of each cycle or when starting a subsequent wash
cycle prior to the next programme being selected and started.
O
Spin speed indicator light
When you set a program, the maximum possible spin speed will be automatically shown by
the relevant indicator light.
Choosing a smaller spin speed by the appropriate button, the relevant indicator light will go on.
12
Q
13
TABLE OF PROGRAMMES
PROGRAMME
SELECTOR ON:
PROGRAM FOR:
WEIGHT
MAX
kg
TEMP. CHARGE DETERGENT
°C
II
Resistant fabrics
Cotton, linen
Cotton, mixed
resistant
Cotton, mixed
Whites
7
90°
●
●
Whites with
Prewash
7
60°
●
●
7
60°
●
●
Non fast coloureds
7
40°
●
●
Delicates
7
30°
●
●
Fast coloureds with
Prewash
*
3,5
60°
●
●
Fast coloureds
3,5
60°
●
●
Synthetics
3,5
50°
●
●
Non fast coloureds
3,5
40°
●
●
Rinse
-
-
Fast spin
-
-
Drain only
-
-
Delicates
2
40°
“MACHINE
WASHABLE”
woollens
1,5
30°
Hand wash
1
Rapid 29 minute
*
*
*
*
*
Mixed fabrics and synthetics
Mixed, resistant
Cotton, mixed fabrics,
synthetics
Synthetics (nylon,
perlon), mixed cotton
**
Fast coloureds
*
*
*
*
*
●
30°
●
●
2
40°
●
●
Resistant fabrics
3,5
60°
●
●
Resistant fabrics
7
40°
●
●
“ALL”
system programme
7
40°
●
●
3,5
-
5
-
*
When washing heavily soiled laundry it is recommended the load is reduced to 4 kg maximum.
Information for the test laboratories
(Ref. EN 50229 Standards)
●
Washing
Use the programme **
Drying
First drying with 5 kg (the load consist: pillowcases and hand-towels) selecting the cotton
drying programme (
) cupboard dry (
).
Second drying with 2kg (the load consist: 2 sheets and hand towels) selecting the cotton
drying programme (
) 90 minutes (90’).
* Programmes for automatic drying.
●
*
Please read these notes
The spin speed may also be reduced, to match any guidelines suggested on the fabric label, or for
very delicate fabrics cancel the spin completely this option is available with a spin speed button.
●
*
●
●
●
Very delicate fabrics
SpecialS
I
*
Cotton - Drying
Mixed - Drying
14
15
Programme selector
For the various types of fabrics and various degrees of dirt the washing machine has different
programme bands according to: wash cycle, temperature and length of cycle (see table of
washing cycle programmes).
COTTONS
The Cotton programme is designed for maximum washing and rinsing
efficiency. With spin cycles in between, the programme guarantees the
laundry is rinsed perfectly. The final spin cycle ensures laundry is spun dry
as much as possible up to the maximum speed.
The Cotton programme includes a Prewash cycle. This option is
particularly useful for really dirty loads and can be used independently of
the main wash programme. Additional detergent for the Prewash part of
the programme should be added to the first compartment of the soap
drawer labelled "I" (please refer to the section of this manual entitled
“Detergent”). We recommend you use only 20% of the quantity used for
the main wash programme.
MIXED AND SYNTHETIC FABRICS
The main wash and rinse gives the best results thanks to the rotation
rhythms of the drum and to the water levels.
A gentle spin will mean that the fabrics become less creased.
SPECIAL “RINSE” PROGRAMME
This programme carries out three rinses with a intermediate spin (which
can be reduced or excluded by using the correct button). It can be used
for rinsing any type of fabric, eg. use after hand-washing.
SPECIAL “SPIN” PROGRAMME
Programme “SPIN” carries out a maximum spin (which can be reduced by
using the correct button).
DRAIN ONLY
This programme drains out the water.
16
SPECIAL DELICATE FIBRES
This is a new wash cycle which alternates washing and soaking and is
particularly recommended for very delicate fabrics. The wash cycle and
rinses are carried out with high water levels to ensure best results.
WOOLMARK PROGRAMME
A programme dedicated to washing fabrics labelled with the woolmark .
The cycle comprises of alternate periods of activity and pauses. The
programme has a maximum temperature of 30° and concludes with 3
rinses and a short spin.
“HAND WASH”
This washing machine also has a gentle Hand Wash programme cycle.
This programme allows a complete washing cycle for garments specified
as “Hand Wash only” on the fabric care label. The programme has a
temperature of 30°C and concludes with 3 rinses and a slow spin.
DAILY WASH 40°C – FAST 29’
A complete washing cycle (wash, rinse and spin), able to wash in
approximately 29 minutes:
- a maximum load of 2 kg;
- lightly soiled fabrics (cotton and mixed fabrics)
We recommend, with this programme, a 20% detergent loading dose
(compared to the normal one), in order to avoid detergent waste.
“A” WASH 59 '
This specially designed programme maintains the high quality wash
performance identified with the “A” rating whilst greatly reducing the wash
time. The programme is designed for a maximum load of 3 kg with a
temperature of 60°C and concludes with 2 rinses and a high speed spin
sequence.
AA SPECIAL PROGRAMME AT 40°C
This special programme has been studied to allow you to obtain the best
washing performance, even at full load, as the 60°C Cotton programme
(the normative cycle), but with the advantage of an energy saving due to
40°C temperature, instead of 60°C.
17
“ALL” PROGRAMME
This is an exclusive system and involves 2 great advantages for the
consumer:
• to be able to wash together different type of fabrics (e.g. cotton +
synthetic etc…) FAST COLOUREDS;
•to wash with a considerable energy saving.
The "ALL" programme has a temperature of 40°C and alternate dynamic
phases (the basket that turns) to static phases (fabrics in soak in phase
of rest) with a duration programme that almost reaching the 2 hours.
The energy consumption for the complete cycle is only 850 W/h.
Important:
•the first washing of new coloureds fabrics must be done separately;
• in every case, never mix NON-FAST COLOUREDS fabrics.
Automatic Variable Capacity
The washing machine is fitted with an automatic reduction in consumption system (known as
Automatic Variable Capacity).
This system enables the machine to use the amount of water needed to wash and rinse the
laundry in relation to the particular load.
This results in a reduction in the amount of water used and electricity needed to heat it to the
minimum required, without in any way compromising the washing and rinsing performance.
In fact the amount of water and electricity used will always be appropriate for the amount of
washing.
The washing machine therefore ensures you achieve excellent washing results whilst
respecting the environment and saving you money.
DRYING
Note: Dispensers used for concentrated powders and liquid
detergents must be removed from the drum before commencing the
tumble drying programmes.
The drum changes direction during the drying cycle to prevent the laundry
from tangling and hence produce even drying. Cool air is used during the
last ten minutes of the drying cycle to minimise creasing.
HIGH HEAT
High temperature drying programme for Cottons and linen items, always
refer to the care label
LOW HEAT
Low temperature drying programme for synthetics and mixed fibres,
always refer to the care label.
18
19
Detergent drawer
R
Detergents, washing aids and amounts to use
The detergent drawer is split into 3 compartments:
Choice of detergent
General purpose detergents
- the compartment labelled "I" is for prewash detergent;
-
- the compartment labelled " " is for special additives,
fabric softeners, fragrances, starch, brighteners etc;
-
- the compartment labelled "II" is for main wash
detergent.
-
Powder detergents, for a thorough wash, with bleaching agent, particularly suitable for
use in hot wash programmes (60°C and over), for heavily soiled and stained laundry.
Liquid detergents, particularly suitable for grease stains, such as greasy skin marks,
cosmetics and oil.
These detergents are not suitable for washing stained laundry, as they do not contain
bleach.
Biological detergents, not all the products available give a really thorough wash.
Additional laundry aids
NOTE:
Some detergents are difficult to
utilise. Ensure to use an in drum
dispenser if recommended by
the detergent manufacturer.
Note: Only put liquid products in the compartment
labelled “
”. The machine is programmed to
automatically take up additives during the final rinse
stage for all wash cycles.
20
-
Water softener, means less detergent can be used where water hardness is classed as
hard to very hard.
Prewash substances, for the programmed treatment of stains prior to the main wash.
Using them means the subsequent wash can be at a low temperature or with bleach-free
detergents.
Fabric softener, prevents static build-up in synthetic fabrics and softens fabrics.
If you own a tumble dryer, clothes are softened even without the use of a fabric softener.
Do not put solvents in the washing machine!
Keep detergents and other laundry products out of children’s reach.
Before pouring in the detergent check that there are no foreign bodies in the detergent
drawer.
Dosage details are usually shown on the detergent packaging. Follow those instructions.
21
Dosages
Only use detergents which are suitable for use in a washing machine.
You will obtain the best results from your wash with the minimum use of chemical products
and the best care for your laundry if you take into consideration the degree of soiling as well
as the type of detergent to choose.
The amount of detergent to use depends on:
- water hardness: depending on the hardness of the water and the type of detergent used, it
is possible to reduce the amount of detergent.
- the degree of soiling: it is possible to reduce the amount of detergent used depending on
the degree of soiling.
- amount of laundry: it is possible to reduce the amount of detergent when washing only a
small amount of laundry.
Useful advice for users
Tips on using your domestic appliance in the most environmentally-friendly and economical
way
Do a full load in your washing machine
To prevent any possible waste of energy, water or detergent we recommend that you put a
full load in your washing machine, not exceeding the recommended maximum load size.
Up to 50% energy saving can be made with one full load compared to two half load washes
When is prewashing really needed?
Dosage for powder detergent
For normal and low concentration detergents: for normally soiled laundry choose a
programme without prewash.
Put the detergent in compartment “II” of the drawer.
For heavily soiled laundry, choose a programme with prewash.
Put 1/4 of the detergent in compartment “I”, 3/4 in compartment “II” of the drawer.
When using water softeners, first put in the detergent, then add the softener to compartment “II”.
For highly concentrated detergents not in single dose format, follow what is shown on pack
exactly as regards type and amount of dosage.
To avoid the difficulty of checking if the detergent has been taken up, use the dosage aids
provided in the detergent packaging.
Liquid detergent dosage
Liquid detergents may be used in accordance with the instructions on the relevant
packaging, for all programmes without prewash, by using the special container which is
placed in the drum or, for those models that have it, in the special insert for liquid detergents.
22
Only with particularly dirty loads!
Energy savings of 5 to 15% are made by not selecting the prewash option for normal soiled
laundry.
Which wash temperature should you choose?
Using stain removers before machine washing reduces the need to wash at temperatures
over 60°C.
Energy savings of up to 50% can be made by using a 60°C wash temperature rather than
90°C.
Before using a drying programme...
SAVE energy and time by selecting a high spin speed to reduce the water content in laundry
before using a drying programme.
23
Main wash
Sorting the laundry
-
It is recommended you wash only items which are machine washable with water and
detergent and not dry-clean items.
-
If you need to wash rugs, bedspreads or other heavy items, it is best not to spin them.
-
Sort the laundry according to fabric type, degree of soiling and wash temperature: Always
follow the wash care advice on the garment label for the most suitable care and
treatment of the laundry
Laundry for hot wash
Coloured, easy-care materials
Delicates and wool
Wash by hand
Items labelled with the following symbol are not suitable for machine washing:
Dry clean
For very delicate items, such as net curtains, underwear, tights etc., you are advised to
use a laundry net or wash bag.
Woollen items must be labelled with the "Pure New Wool" symbol to be washed in the
machine
, and must also be labelled "non-matting" or "machine washable".
Colour often leaks from new coloured items.
This can then colour other lighter items being washed.
We therefore recommend that coloured items should be washed for the first time
separately.
For future washes, colourfast items can only be washed with whites up to 40°C.
-
Note: when sorting laundry
-
check there are no metal objects in the laundry
(such as paper clips, safety pins, pins, coins
etc...);
button up pillowcases, fasten zips, hook & eye
fasteners, belts and long dressing gown cords;
remove curtain hooks;
pay close attention to the labels on items
if you notice stubborn stains whilst sorting the
laundry, remove them using a special detergent or
a special stain remover.
- We recommend that you do not do a full load of towelling items only as these become too
heavy since they absorb a lot of water.
24
The correct way to wash
Preparing the laundry
A) Select the laundry.
Loading the laundry
B) Open the porthole.
C) Put the laundry in the washing machine.
Close the porthole again, ensuring that no items of
laundry are obstructing the lock.
Putting detergent in machine
D) Open the drawer, choose the detergent and put in
the correct amount, according to the manufacturer’s
instructions and the advice on page 21.
Add any other laundry aids (see page 21). Close the
drawer again.
Selecting the wash programme
Refer to the programme guide or the programme descriptions on the machine to select the
most suitable programme.
Turning the selector knob, the required programme is activated.
Wait for the “STOP” indicator light to flash.
Press additional function buttons (if required).
Check that the tap is turned on and that the discharge hose is positioned correctly.
Press the "Start/Pause" button.
When the "Start/Pause" button is pressed the machine sets the working sequence in motion.
The programme carries out with the programme selector stationary on the selected
programme till cycle ends.
Warning: If there is any break in the power supply while the machine is operating, a special
memory stores the selected programme and, when the power is restored, it continues where
it left off.
When the programme is finished
At the end of the programme the indicator light “STOP” will go on.
Wait for the door lock to be released (about 2 minutes after the programme has finished).
The "Door Security" indicator light will go out.
Switch off the machine by turning the programme selector on the “OFF” position. Open the
door and remove the laundry. Turn off the tap.
25
Automatic washing/drying
DRYING
DON’T DRY GARMENTS MADE FROM FOAM RUBBER
OR FLAMMABLE MATERIALS.
IMPORTANT:
THIS DRYER CAN ONLY BE USED FOR LAUNDRY
WHICH HAS BEEN WASHED AND SPIN DRIED.
Warning: only a maximum 5 kg of dry laundry can be loaded.
Refer to the list of washing programmes according to fabrics to be washed (e.g. very dirty
cotton) and without pressing Start button, prepare wash as described:
Selecting the wash programme
Refer to the programme guide or the programme descriptions on the machine to select the
most suitable programme.
Turning the selector knob, the required programme is activated.
Wait for the “STOP” indicator light to flash.
Press additional function buttons (if required).
Check that the tap is turned on and that the discharge hose is positioned correctly.
DRYING:
WARNING:
Indications given are general, therefore some practice is needed for the best drying results.
We recommend setting a lower drying time than indicated, when first using, so as to
establish the degree of dryness required. We recommend not to dry fabrics that fray easily,
such as rugs or garments with a deep pile, to avoid air duct clogging.
The water is then conveyed to the drain circuit, wich is sealed and therefore, no steam can
be released outside.
Important
Never open the door after the drying cycle has begun wait until the cool down period provided for by the
cycle.
Select the degree of dryness that you require.
This ranges from Extra Dry (
) for bath towels and bathrobes, through Cupboard Dry
(
) for items that will be put away without ironing, to iron dry (
) that leaves the
laundry suitable for ironing.
If you wish to select a timed drying cycle, press the “drying programme selection” button until
the required time indicator lights up.
Press the "Start/Pause" button.
When the "Start/Pause" button is pressed the machine sets the working sequence in
motion.
The programme carries out with the programme selector stationary on the selected
programme till cycle ends.
The washer-dryer will then complete the entire drying programme.
The drying programme indicator will be on until the cool down phase will begin and the
indicator “
” will go on.
When the programme is finished
Only dry pre-spun laundry
The washer/dryer can perform two types of drying:
1 Cotton, terry towelling, linen, hemp fabrics, etc...
symbol on programme dial (Q).
During drying phase the drum will accelerate to a higher speed to distribute the load
and to optimize the drying performance
2 Mixed fabrics (synthetics/cotton), synthetic fabrics
symbol on programme dial (Q).
At the end of the programme the indicator light “STOP” will go on.
Wait for the door lock to be released (about 2 minutes after the programme has finished).
The "Door Security" indicator light will go out.
Switch off the machine by turning the programme selector on the “OFF” position. Open the
door and remove the laundry. Turn off the tap.
26
27
Drying cycle
The correct way to dry:
- Open door.
- Fill with up to 5 kg - in case of large items (e.g. sheets) or very absorbent items (e.g.
towels or jeans), it is a good idea to reduce the load.
- Close door.
- Turn programme dial to
cotton.
Select the degree of dryness that you require.
This ranges from Extra Dry (
) for bath towels and bathrobes, through Cupboard Dry
(
) for items that will be put away without ironing, to iron dry (
) that leaves the
laundry suitable for ironing.
If you wish to select a timed drying cycle, press the “drying programme selection” button
until the required time indicator lights up.
DOUBLE-SKIN DOOR
The appliance door is fitted with a protective shield to prevent
contact with the glass door which can reach high temperatures,
during the drying cycle.
It should not be necessary to remove the shield from the machine
during the normal course of use.
Do not use alcohol-based scourers and / or thinners on the outside of your washing machine,
just a wipe with a damp cloth will suffice. The washing machine needs very little maintenance:
- Cleaning the drawer compartments.
- Cleaning the door glass.
Cleaning the drawer compartments
Even if it is not strictly necessary, it is good to clean the
compartments for bleaching detergents and additives
occasionally.
A) To do this you just need to pull them out firmly, but
without forcing them.
B) Clean everything in the compartment under running
water.
C) Put everything back in its proper place.
Cleaning the door glass
Regularly clean the door glass with a damp cloth. A build
up of soiling and
residues from the water may result in water leaking from
the door.
Do not use abrasive cleaners as they can scratch the
surface.
Warning: do not touch door for any reason.
• Make sure water inlet valve is open.
• Make sure water drain is correctly positioned.
Warning:
do not dry woollen garments or articles with special padding,
(e.g. quilts, quilted anoraks, etc.).
Delicate fabrics if garments are drip/dry, load less items ao as to
prevent creasing.
Press the START button.
The drying phase will begin with the programme dial fixed on the
end of drying.
Cleaning and routine maintenance
symbol until the
The drying programme indicator will be on until the cool down phase will begin and the
indicator “
” will go on.
Transporting the appliance or long
periods when appliance is not in
use
If the appliance is being transported or is out of use for
long periods in unheated places, all remaining water
must be completely removed from the hoses.
Ensure mains power is off, then unclip the hose and
point it downwards into a basin until all the water has
emptied out.
When finished, repeat the operation in the reverse order.
When the programme is finished
At the end of the programme the indicator light “STOP” will go on.
Wait for the door lock to be released (about 2 minutes after the programme has finished).
The "Door Security" indicator light will go out.
Switch off the machine by turning the programme selector on the “OFF” position. Open the
door and remove the laundry. Turn off the tap.
28
29
Investigating malfunctions
What might be the cause of…
Defects you can remedy yourself
MALFUNCTION CAUSE
REMEDY
1. Does not work on any
programme
Plug not in socket.
Not switched on.
Power failure.
Fuse blown.
Door open.
Plug it in.
Switch on.
Check.
Check.
Close door.
2. Does not fill with water
See cause 1.
Tap turned off.
Programme selector not correctly
positioned.
Fill hoses are kinked
Check.
Turn on tap.
Position programme selector
correctly.
Straighten fill hoses
Kink in discharge hose.
Straighten discharge hose.
House drain is blocked
Clean drain
4. Water on floor around
the washing machine
Leaking gasket between tap and water
inlet hose.
House drain is blocked
Soap drawer blocked with soap residues
Replace gasket and tighten hose and
tap well.
Clean drain
Clean soap drawer
5. Does not spin
Water has not yet drained away.
Wait a few minutes for machine to empty.
"No spin" selected (certain models only). Reset button or turn "no spin" knob.
6. Machine vibrates a lot
during spin
Washing machine not completely level.
Transit brackets not removed yet.
Load not distributed evenly.
Adjust the special adjustable feet.
Remove transit brackets.
Rearrange the laundry evenly.
7. Door will not open
Two minutes have not elapsed since the
programme finished.
Wait two minutes.
3. Water does not drain
away
Note:
The use of environmentally-friendly, phosphate-free detergents can have the following effects:
- waste water from rinsing may be cloudier because of the presence of zeolites held in
suspension, without the rinse performance being adversely affected;
- presence of white powder (zeolites) on laundry after washing, which is not absorbed by
the fabric and does not alter the colour of the fabric.
- The presence of foam in the final rinsing water is not necessarily an indication of poor
rinsing.
- Anionic surfactants used in washing detergent formulae often prove to be difficult to
remove from the laundry itself and, even in small quantities, can still cause considerable
foam production.
- Carrying out more rinse cycles does not serve any purpose in such cases.
This appliance is marked according to the European directive
2002/96/EC on Waste Electrical and Electronic Equipment (WEEE).
By ensuring this product is disposed of correctly, you will help prevent
potential negative consequences for the environment and human health,
which could otherwise be caused by inappropriate waste handling of this
product.
The symbol on the product indicates that this product may not be treated
as household waste. Instead it shall be handed over to the applicable
collection point for the recycling of electrical and electronic equipment
Disposal must be carried out in accordance with local environmental
regulations for waste disposal.
For more detailed information about treatment, recovery and recycling of
this product, please contact your local city office, your household waste
disposal service or the shop where you purchased the product.
During drying phase the drum will accelerate to a higher speed to distribute the load
and to optimize the drying performance
The machine makes a
different noise when
spinning! This is because it
has a brush motor for better
performance.
Only a small level of water can be
seen in the drum! This is because
new machines do not use much
water, yet achieve the same
standard of washing and rinsing.
30
31
SETTING UP + INSTALLATION
1
Remove the polystyrene base and place the machine near
its permanent position (diagram 1).
Carefully cut through the hose retaining clip at the rear of
the appliance (diagram 2).
Remove the 3 fixing screws marked (A) and remove the 3
spacers marked (B) (diagram 3).
2
Remove the screw (C).
A spacer will fall inside the machine.
By tilting the machine, remove the above mentioned spacer.
Cover the 4 holes using the caps provided in the instruction
booklet pack (diagram 4).
Fig. 2
3
4
Technical data
■ Max. load of dry laundry for washing
■ Max. load of dry laundry for drying
■ Water pressure
■ Cold fill only
■ Spin Speed
7 kg
5 kg
0,05 ÷ 0,8 MPa
1400 r.p.m.
Measurements
■ Width
■ Depth
■ Height
60 cm
54 cm
82 cm
WARNING:
DO NOT LEAVE THE PACKAGING WITHIN REACH OF CHILDREN AS IT IS A POTENTIAL
SOURCE OF DANGER.
Apply the insulation sheet of corrugated material to the base
as shown.
NB: For specifications regarding electrical data, see the data panel on the front of the washing
machine (porthole area) - as shown in diagram above.
Appliance complies with European Directives 73/23/EEC and 89/336/EEC, replaced by
2006/95/EC and 2004/108/EC, and subsequent amendments.
32
Note: We recommend you keep the screws to
immobilise the machine for future transit.
The Manufacturers will not be responsible for any
possible damage to the machine caused by not
following the rules relating to releasing the mechanism.
The user is responsible for all costs of installation.
33
Installation & Decor Door Fitting
The appliance requires the following
space:
Snap mount plastic cover cap ‘H’ into the lower
hinge position.
Adjustable Feet
Mount the door and hinges to the front of the
appliance using screws ‘L’.
Note: It is recommended that where possible
the décor door is hinged on the same side as
the appliance door as this will give greater
space to load and unload the washing.
The feet are adjustable to give an appliance
height of 825 mm – 849 mm.
It is important that the feet are adjusted to
ensure that the appliance is level, this is
essential to ensure quiet operation.
Once the feet have been adjusted to the
correct height it is important that they are
locked in position using the locking nuts.
G
Fasten the magnetic catch striker plate ‘D’ to
the front of the appliance, placing the rubber
washer ‘E’ under the plate and screw in place
with screws ‘G’.
2x
L
A
4x
4x
Fitting the Décor Door
The front of the appliance has been drilled to
accommodate the hinges to enable the door to
be opened from the left or right hand side.
We suggest you proceed as follows:
1) Standard Height Door & Dummy Drawer
Front
Screw the hinges onto the décor door, ‘A’ then
fasten the dummy drawer front to the top edge
of the door. Ensure that the gap between the
door & drawer front matches the units on either
side.
Fasten the magnetic catch ‘B’ using screw ‘C’
to the décor door.
34
Décor Strip
A décor strip is required to fill the gap between the top of the appliance and the underside of
the worktop. We recommend that facia SKD4189 is used for this purpose and is screwed to
the underside of the work or by KD fixings to the adjacent cabinets.
Note: The infill facia may need to be cut to fit dependant on the height of the appliance.
C
1x
2) Full Height Door
If a full height door is being used then a top hinge hole will have to be drilled in the door. The
distance between the two hinge holes centres is 384mm and 21.5mm from the edge of the
door.
The hole diameter for the hinge is 35mm and should be drilled to a depth of 12mm, care must
be taken to ensure that you do not drill through the door. The pilot holes for fixing the hinge
should be drilled with 2mm diameter drill.
35
Water connection
ELECTRICAL CONNECTIONS
The appliance must be connected to the water mains using new
hose-sets.
The old hose-sets should not be re-used.
The machine has an inlet hose with 3/4" B.S.P threaded end
connection to attach between the threaded connector on the
appliance and the cold water supply.
After installation, the appliance must be positioned so that the plug is accessible.
If the plug we supply does not fit
CUT IT OFF AND DESTROY IT!
You can’t use it on other appliances, and the exposed wires could be dangerous if plugged in.
To fit a replacement plug, proceed as follows:
This machine only uses cold water, therefore
only one hose is needed to connect to the cold
water supply. Do not connect to the hot supply.
Cold fill is an energy efficient system. Only the
water required for the washing is heated.There
is no loss of heat in the pipeline from a hot
water tank or boiler to the machine.
Connect
to the terminal in the plug
green and yellow wire
marked with the letter E,
OR marked
with the symbol,
OR coloured green,
OR coloured green and yellow.
blue wire
marked N
OR coloured black.
brown wire
marked L
OR coloured red.
WARNING
This appliance must be earthed
min 4 cm
max 100 cm
Fuses and plugs
This appliance should be used only on a socket with a minimum rating of 13 Amp.
+2,6 mt max
min 50 cm
max 85 cm
Our ready-fitted plug is already equipped with a 13 amp fuse which is BS 1362 ASTA
approved. Any replacement should be exactly the same.
If the fuse cover is lost, do not use the plug until it is replaced. A correct replacement fuse
cover (obtainable from your local retailer) must be the same colour as shown or named on
the insert on the base of the plug.
Note: It is advisable to turn off the tap after each wash
to isolate the washing machine from the water supply.
The appliance must not be installed behind a lockable door, a sliding door or a door with a
hinge on the opposite side to that of the washer dryer.
For the washing machine to function properly the terminal end of the discharge hose (mouth)
must be at a minimum of 50 cm and a maximum of 85 cm from the ground.
36
37
The manufacturer declines all responsibility in the event of any printing mistakes in
this booklet. The manufacturer also reserves the right to make appropriate
modifications to its products without changing the essential characteristics.
HJA 8704
0 845 0060006
41031846
Issue 1
June 2009
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising