CA
HF
Q1**
Q2**
L
M*
J
U*
N*
O*
V*
P*
USER MANUAL
E
D
C
F
K
S
W*
A
GP
B
Q**
PRINTED IN P.R.C.
48011754-1
1
G
R**
I
T
H
X*
* Certain models only
** Certain models only, nozzles may vary according to model
2
3
**
4
5
14 14
15
16
17 17
*
6
**
7
8
*
9
18 18
19
20
21 21
10
11
*
12
*
13
* Certain models only
** Certain models only, nozzles may vary according to model
Do not spray with or pick up flammable liquids, cleaning
fluids, aerosols or their vapours.
INSTRUCTIONS FOR SAFE USE
This appliance should only be used for domestic cleaning,
as described in this user guide. Please ensure that this
guide is fully understood before operating the appliance.
Do not run over the power cord when using your appliance
or remove the plug by pulling on the power cord.
Do not continue to use your appliance if it appears faulty.
Do not leave the appliance plugged in. Always switch off
and remove the plug from the socket after use, or before
cleaning the appliance or any maintenance task.
HOOVER service: To ensure the continued safe and efficient
operation of this appliance we recommend that any servicing
or repairs are only carried out by an authorised HOOVER
service engineer.
This appliance can be used by children aged from 8 years
and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the
hazards involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by
children without supervision.
Do not stand on or wrap the cord around arms or legs when
using your appliance.
Do not use the appliance to clean animals or people.
Do not position the appliance above you when cleaning the
stairs.
If the power cord is damaged stop using the appliance
immediately. To avoid a safety hazard, an authorised
HOOVER service engineer must replace the power cord.
Use only attachments, consumables or spares recommended
or supplied by HOOVER.
The Environment
The symbol on this appliance indicates that this appliance may not be treated
as household waste. Instead it must be handed over to the applicable collection
point for the recycling of electrical and electronic equipment. Disposal must
be carried out in accordance with local environmental regulations for waste
disposal. For more detailed information about treatment, recovery and recycling
of this appliance, please contact your local city office, your household and waste disposal
service or the shop where you purchased the appliance.
Static electricity: Some carpets can cause a small build up of
static electricity. Any static discharge is not hazardous to health.
This appliance complies with the European Directives 2014/35/EU, 2014/30/EU
and 2011/65/EU.
Keep hands, feet, loose clothing and hair away from rotating
brushes.
Do not use your appliance out of doors or on any wet surface
or for wet pick up.
CANDY HOOVER GROUP S.r.l. Via Privata Eden Fumagalli, 20861 Brugherio (MB) Italy
Do not pick up hard or sharp objects, matches, hot ashes,
cigarette ends or other similar items.
1
GETTING TO KNOW YOUR CLEANER
A.
B.
C.
D.
E.
F.
G.
H.
I.
J.
K.
L.
M.
N.
O.
P.
Q.
Cleaner main body
Dust Container
Dust Container Handle
Dust Container Release Button
Cleaner Handle
On/Off Button
Cord Rewind Button
Nozzle Parking Slot
Exhaust Filter Cover
Hose
Hose Release Button
Hose Handle
Suction Regulator*
Standard Tube*
Telescopic Tube*
Telescopic Tube Adjuster*
Carpet and Floor Nozzle(GP)**
R.
S.
T.
U.
V.
W.
X.
Y.
Q1. Carpet Nozzle (CA)**
Q2. Hard Floor Nozzle (HF)**
Floor Type Selector Pedal**
Pre-motor Filter and Protective Mesh
Exhaust Filter
Accessories Holder*
2 in 1 Tool (Crevice Tool/Dusting Brush)
Pet Hair Remover Mini Turbo Nozzle*
Allergen Remover Mini Turbo Nozzle*
Hard Floor Nozzle*
USING YOUR CLEANER
1.
2.
3.
4.
5.
6.
7.
Extract power cord and plug it into the power supply. [5] Do not pull the cord beyond
the red marker.
Adjust the telescopic tube* to the desired height by moving the telescopic tube adjuster
up and raise or lower the handle to the most comfortable cleaning position. [6]
Carpet & Floor Nozzle**. Press the floor type selector pedal on the nozzle [7] to
select the ideal cleaning mode for the floor type.
Hard Floor – Brushes are lowered to protect the floor.
Carpet – Brushes are raised for the deepest clean.
Switch the cleaner on by pressing the On/Off button on the cleaner main body. [8]
Vary the suction as desired by closing or opening the suction regulator* on the hose
handle. [9]
Switch off at the end of use by pressing the On/Off button. [8] Unplug and press the
cord rewind button to wind the power cord back into the cleaner. [10]
To store your cleaner, park the nozzle in the parking slot at the rear of the cleaner
main body. [11]
ACCESSORIES
To obtain the best performance and efficiency it is recommended that the correct nozzles
are used for the main cleaning operations. These nozzles are indicated in the diagrams
by the letters GP, HF or CA.
A nozzle type GP can be used to clean both carpet and hard floor.
A nozzle type HF is suitable for use only on hard floor.
A nozzle of type CA is suitable for use only on carpet.
The other nozzles are accessories for specialist cleaning tasks and are recommended
for occasional use only.
All accessories can be fitted to the hose handle or the end of the tubes.
2 in 1 Tool combines several functions into one tool:
Crevice Tool – For corners and hard to reach areas. [12]
Dusting Brush – For bookshelves, frames, keyboards and other delicate areas. [13]
ASSEMBLING YOUR CLEANER
Remove all components from the packaging.
1.
2.
3.
4.
Pet Hair Remover Mini Turbo Nozzle* - Use the mini turbo nozzle on stairs or for deep
cleaning on textile surfaces and other hard to clean areas. Particularly suitable for pet
hairs removal. [1X]
Allergen Remover Mini Turbo Nozzle* – Use the mini turbo nozzle on stairs or for
Connect the hose to the cleaner main body, ensuring it clips and locks into position.
To release the hose: simply press the two hose release buttons on the hose end
and pull it out. [2]
Connect the hose handle to the telescopic tube* upper end. [3]
Connect the telescopic tube* lower end to the carpet and floor nozzle**. [4]
*Certain Models Only ** Certain models only, nozzles may vary according to model
2
mesh and the filter against the side of a bin to remove excess dust and wash both
of them under warm water. [18] Do not use hot water or detergents.
4. Remove excess water from the filter and leave it to dry fully before reusing. [21]
5. Once the filter is fully dry, reassemble the filter pack (protective mesh and filter) and
refit to cleaner.
IMPORTANT: Do not use the product without the pre-motor filter pack fitted.
IMPORTANT: Always ensure the filter packs are fully dry before use.
deep cleaning on textile surfaces and other hard to clean areas. Particularly suitable for
allergen removal. [1Y]
Hard Floor Nozzle* – For parquet floors and other delicate floors. [1Z]
IMPORTANT: Do not use the Mini Turbo Nozzles on rugs with long fringes, animal hides
and carpet pile deeper than 15mm. Do not keep the nozzle stationary while the brush is
rotating.
To access the exhaust filter:
1.
2.
CLEANER MAINTENANCE
Emptying the Dust Container
3.
4.
When the dust reaches the max level indicator on the container, empty the dust container.
IMPORTANT: To maintain optimum performance, do not allow the dust to sit higher than
the max level.
1. Release the dust container by sliding the dust container release button towards the
front of the cleaner. Lift the dust container from the cleaner main body. [14]
2. Before emptying the Dust Container, gently tap it against the side of a bin to release
any excess dust from the filter.
3. To empty the Dust Container, hold the Dust Container over a bin with one hand and
use the other hand to press the Dust Container Flap Opening Button to release the
dust into the bin. [15]
4. Close the Dust Container Flap and refit the Dust Container to the cleaner main body.
REMEMBER: Do not use hot water or detergents. In the unlikely event of the filters
becoming damaged, fit a Genuine Hoover consumable. Do not try and use the product
without a filter fitted.
Removing a blockage
1.
2.
Cleaning the washable filters
The cleaner is fitted with a pre-motor and exhaust filter. To maintain optimum cleaning
performance, regularly clean the filters. Remove excess dust from the filters by gently
tapping them against the side of a bin. The filters should be washed after every 5
container empties.
Check if the dust container is full. If so refer to ‘Emptying the Dust Container’.
If the dust container is empty but suction is still low:
A.
Do the filters need cleaning? If so refer to ‘Cleaning the Washable Filters’.
B.
Check if there is any other blockage in the system - Use a rod or pole to remove
any blockage from the extension tube or flexible hose.
C.
Check if pre-motor filter is fitted and filter door is closed
Warning (Certain models only*) - If the cleaner is used for a significant period of time
with a blockage, a thermal cut out will switch the cleaner off to prevent overheating.
The bag check indicator turn green once the cleaner has switched off to signal that the
thermal cut out has been activated. If this should happen, switch the cleaner off, unplug
and correct the fault. It will take about 45 minutes for the cut out to automatically reset.
IMPORTANT: All bagless cleaners require regular filter cleaning. Failure to clean
your filters may result in air blockage, overheating and product failure. This may
invalidate your guarantee.
USER CHECKLIST
IMPORTANT: Regularly check and maintain the filters by following the filter
maintenance instructions, it is also recommended that you purchase new filters
after every 3rd filter wash. This will maintain your cleaners performance.
Should you have a problem with the product, complete this simple user checklist
before calling your local Hoover service.
To access the Pre-Motor filter:
1. Empty the Dust Container as described in ‘Emptying the Dust Container’. Then,
keeping the Dust Container Flap open:
2. Remove the pre-motor filter by rotating it clockwise at the bottom of the Dust
Container. [16]
3. Separate the protective mesh from the filter. [17] Gently tap both the protective
*Certain Models Only ** Certain models only, nozzles may vary according to model
Unclip the exhaust grid from the rear of the cleaner. [19]
Separate the filter from the grid and wash the filter under warm water. [20] Do not use
hot water or detergents.
Remove excess water from the filter and leave to dry fully before reusing. [21]
Remount the filter into the grid and refit it to the cleaner.
•
•
•
•
3
Is there a working electricity supply to the cleaner? Please check with another electrical
appliance.
Is the Bag over-filled? Please refer to ‘Cleaner Maintenance’.
Is the filter blocked? Please refer to ‘Cleaner Maintenance’.
Is the hose or nozzle blocked? Please refer to ‘Removing a Blockage’.
•
Has the cleaner overheated? If so, it will take approximately 45 minutes to automatically
reset.
IMPORTANT INFORMATION
Hoover spares and Consumables
Always replace parts with genuine Hoover spares. These are available from your local
Hoover dealer or direct from Hoover. When ordering parts always quote your model number.
Hoover Customer Helpline Service
Should any faults occur with your cleaner during the first 12 months contact the Hoover
Customer Helpline on the number below.
Tel: 08444 995 599
Email: [email protected]
Quality
BSI ISO 9001
Hoover’s factories have been independently assessed for quality. Our products are
made using a quality system which meets the requirements of ISO 9001
Your Guarantee
The guarantee conditions for this appliance are as defined by our representative in the
country in which it is sold. Details regarding these conditions can be obtained from the
dealer from whom the appliance was purchased. The bill of sale or receipt must be
produced when making any claim under the terms of this guarantee.
Subject to change without notice.
4
">
