Hoover | XP71_EG25001 | Hoover XP71_EG25001 User manual

Hoover XP71_EG25001 User manual
M*
CA
N*
N*
Q1**
T*
M*
HF
S
P*
Q2**
O*
®
U*
F
T*
P*
E
C
O*
L
D
USER MANUAL
B
V*
J
G
H
W*
GP
R
®
PRINTED IN P.R.C.
48011352
1
K
A
I
X*
Q**
* Certain models only
** Certain models only, nozzles may vary according to model
14*
15
16
17
9*
18
19
20
21
*
13
22
23
24
25
3
4
5
6
7
8
10
11
*
12
MI
D
2
* Certain models only
** Certain models only, nozzles may vary according to model
Do not spray with or pick up flammable liquids, cleaning
fluids, aerosols or their vapours.
INSTRUCTIONS FOR SAFE USE
This appliance should only be used for domestic cleaning,
as described in this user guide. Please ensure that this
guide is fully understood before operating the appliance.
Do not run over the power cord when using your appliance
or remove the plug by pulling on the power cord.
Do not continue to use your appliance if it appears faulty.
Do not leave the appliance plugged in. Always switch off
and remove the plug from the socket after use, or before
cleaning the appliance or any maintenance task.
HOOVER service: To ensure the continued safe and efficient
operation of this appliance we recommend that any servicing
or repairs are only carried out by an authorised HOOVER
service engineer.
This appliance can be used by children aged from 8 years
and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the
hazards involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by
children without supervision.
Do not stand on or wrap the cord around arms or legs when
using your appliance.
Do not use the appliance to clean animals or people.
Do not position the appliance above you when cleaning the
stairs.
If the power cord is damaged stop using the appliance
immediately. To avoid a safety hazard, an authorised
HOOVER service engineer must replace the power cord.
Use only attachments, consumables or spares recommended
or supplied by HOOVER.
The Environment
The symbol on this appliance indicates that this appliance may not be treated
as household waste. Instead it must be handed over to the applicable collection
point for the recycling of electrical and electronic equipment. Disposal must be
carried out in accordance with local environmental regulations for waste disposal.
For more detailed information about treatment, recovery and recycling of this appliance,
please contact your local city office, your household and waste disposal service or the
shop where you purchased the appliance.
Static electricity: some carpets can cause a small build up of
static electricity. Any static discharge is not hazardous to health.
This appliance complies with the European Directives 2006/95/EC, 2004/108/EC
and 2011/65/EU.
Keep hands, feet, loose clothing and hair away from rotating
brushes.
Do not use your appliance out of doors or on any wet surface
or for wet pick up.
HOOVER Limited, Pentrebach, Merthyr Tydfil, Mid Glamorgan, CF48 4TU, UK
Do not pick up hard or sharp objects, matches, hot ashes,
cigarette ends or other similar items.
1
Getting to know your cleaner
A.
B.
C.
D.
E.
F.
G.
H.
I.
J.
K.
L.
M.
N.
O.
P.
Q.
R.
S.
T.
U.
V.
W.
X.
Using your cleaner
Cleaner main body
Carry handle
Dust Container
Dust Container handle and latch
On/Off Button
Cord Rewind Button
Filter Door
Filter Door latch
Pre-Motor Filter Pack
Exhaust Filter Door
Exhaust Filter
Parking Slot
Handle*
Suction Control*
Telescopic Tube*
Telescopic Tube Adjuster*
Carpet and Floor nozzle(GP)**
Q1. Carpet Nozzle (CA)**
Q2. Hard Floor Nozzle (HF)**
Surface Selector
Hose
Accessories*
Pet Hair Remover Mini Turbo Nozzle*
Allergen Remover Mini Turbo Nozzle*
Turbo Nozzle*
Parquet Nozzle*
1.
Extract power cord and plug it into the power supply. Do not pull the cord beyond
the red marker. [5]
2. Adjust the telescopic tube to the desired height by holding the handle and moving
the telescopic tube adjuster up or down. [6]
3. Select carpet care control height by pressing the pedal in the nozzle. [7]
Hard Floor – Brushes are lowered to protect the floor.
Carpet – Brushes are raised for the deepest clean.
4. Switch the cleaner on by pressing the On/Off Button on the cleaner main body. [8]
5. Adjust the suction by sliding the suction control to the desired level. [9]
6. Switch off at the end of use by pressing the On/Off Button. Unplug and press the
cord rewind button to wind the power cord back into the cleaner. [10]
7. To store your cleaner adjust telescopic tube to the lowest height setting and park the
nozzle in the park position on the cleaner main body. [11]
Accessories
#1
To obtain the best performance and energy efficiency
it is recommended that the
correct nozzles are used for the main cleaning operations. These nozzles are indicated
in the diagrams by the letters GP, HF or CA.
A nozzle type GP can be used to clean both carpet and hard floor.
A nozzle type HF is suitable for use only on hard floor.
A nozzle of type CA is suitable for use only on carpet.
The other nozzles are accessories for specialist cleaning tasks and are recommended
for occasional use only.
Assembling your Cleaner
It is important to note that this vacuum cleaner is supplied with an Energy Label as required by European Regulation (EU) 665/2013.
Remove all components from the packaging.
If the label shows a red prohibition circle on the left covering the carpet symbol, then this
indicates that the vacuum cleaner is not suitable use on carpets.
1.
If the label shows a red prohibition circle on the right covering the hard floor symbol, then
this indicates that the vacuum cleaner is not suitable for use on hard floors.
2.
3.
Connect the hose to the cleaner main body, ensuring it clips and locks into position.
To release: simply press the two buttons on the hose end and pull. [2]
Connect the tube upper end to the hose handle and store the accessories on the
handle. [3]
Connect the tube lower end to the carpet and floor nozzle**. [4]
#1
NOTE: Dust pick up ability carpet, dust pick up ability hard floor, and energy efficiency
in accord with Commission Regulations (EU) 665/2013 and (EU) 666/2013.
All accessories can be fitted to the end of the handle or the end of the telescopic tube.
3 in 1 tool* – Combines several functions in one, with maximum flexibility by the rotating
body. Reach into awkward areas by rotating the body. The 3 in 1 tool can be stored neatly
*Certain Models Only ** Certain models only, nozzles may vary according to model
2
invalidate your guarantee.
underneath the hose handle.[1] (Depending on model)
IMPORTANT: Regularly check and maintain the filters.
IMPORTANT: Always ensure the filter pack is fully dry before use.
Crevice Tool* – For corners and hard to reach areas. [12]
Furniture Nozzle* – For soft furniture and fabrics.[13]
Dusting Brush* – For bookshelves, frames, keyboards and other delicate areas. To
extend the brushes push the button on the body of the tool. [14]
To access the Pre- Motor filter:
NOTE: Ensure the carry handle is at its down position before opening the filter door.
Parquet Nozzle* – For parquet floors and other delicate floors. [1X]
Turbo Nozzle* – Use the turbo nozzle for deep cleaning on carpets. [1W]
Pet Hair Remover Mini Turbo Nozzle* - Use the mini turbo nozzle on stairs or for deep
cleaning on textile surfaces and other hard to clean areas. Particularly suitable for pet
hairs removal. [1U]
Allergen Remover Mini Turbo Nozzle* – Use the mini turbo nozzle on stairs or for deep
cleaning on textile surfaces and other hard to clean areas, particularly suitable for allergen
removal. [1V]
1.
2.
3.
4.
5.
IMPORTANT: Do not use the turbo and mini turbo nozzles on rugs with long fringes,
animal hides and carpet pile deeper than 15mm. Do not keep the nozzle stationary while
brush is rotating.
To access the exhaust filter:
1. Unlock the exhaust filter door by rotating the door along arrow indicated. [19]
2. Remove the filter pack from recess. [20]
3. Gently tap and wash the filter unit. Do not use hot water or detergents. Remove
excess water from the filter and leave to dry fully before reusing. [21]
4. Reassemble filter pack once fully dry and refit to the cleaner.
Cleaner Maintenance
Emptying the Dust Container
When the dust reaches the max level indicator in the container empty the dust container.
IMPORTANT:To maintain optimum performance do not allow the dust to sit higher than
the max level.
1.
2.
3.
IMPORTANT: Do not use the product without the filter pack fitted.
Cleaning the Airvolution separation unit
Release the container carry handle by lifting the centre latch to detach the dust
container from the main cleaner and pull upward to remove. [15]
Hold the dust container over a bin with one hand and with the other pull the dust
container catch to open the door and empty. [16]
Close the dust container door and refit to the cleaner main body. To lock in place
push the container carry handle down until the latch connects with the main body
of the cleaner. Once correctly retained the carry handle will sits flush with the top
of the cleaner.
This cleaner uses the Airvolution separation system, unique to Hoover. If necessary the
Airvolution separation unit can be removed from the dust container and cleaned.
1.
2.
3.
Cleaning the washable filters
4.
5.
The cleaner is fitted with a filter pack. To maintain optimum cleaning performance
regularly remove the the filters and tap against the side of the bin to release dust.The
filters should be washed every 3 months or when the filter has excessive dust level.
6.
IMPORTANT: All bagless cleaners require regular filter cleaning. Failure to clean
your filters may result in air blockage, overheating and product failure. This may
*Certain Models Only ** Certain models only, nozzles may vary according to model
Unlock the filter door by pulling the filter latch upwards. Open the filter door. [17]
Remove the blue filter pack by pressing down on the retainer catch to release. The
filter pack will pop up. Slide the filter pack out. [18]
Unlatch the filter pack frame.
Remove the micro filter from the pack frame and wash the micro filter by handusing
warm water. Do not use hot water or detergents. Remove excess water from the
filter and leave to dry fully before reusing. [21]
Reassemble to filter pack once fully dry and refit to the cleaner. Press on the top of
the filter to ensure it clips back into place.
3
Remove dust container from the cleaner by releasing the container carry handle to
detach the dust container from the main cleaner and pull upward to remove. [15]
Place the dust container on a flat surface and unclip the clips from either side of the
dust container. [22]
Using the dust container handle lift the dust container upper section containing
theseparation unit from the lower section. [23]
Use a cloth to remove excessive dust from the separation unit’s surface. [24]
Reassemble the dust container upper section. Push clips back to fully close the dust
container. [25]
Refit the dust container to the cleaner. To lock in place push the container carry
handle down until the latch connects with the main body of the cleaner. Once
correctly retained the carry handle will sit flush with the top of the cleaner.
Removing a blockage
1.
2.
dealer from whom the appliance was purchased. The bill of sale or receipt must be
produced when making any claim under the terms of this guarantee.
Check if the dust container is full. If so refer to ‘Emptying the dust container.
If the dust container is empty but suction is still low:
A.
B.
C.
D.
Subject to change without notice.
Do the filters need cleaning? If so refer to ‘Cleaning the washable filters’.
Check if there is any other blockage in the system - Use a rod or pole to remove
any blockage from the extension tube or flexible hose.
Check if pre-motor filter is fitted and filter door is closed
Check if the cyclonic unit needs to be cleaned. Refer to ‘Cleaning the cyclone
unit’
User Checklist
Should you have a problem with the product, complete this simple user checklist
before calling your local Hoover service.
•
•
•
•
•
Is there a working electricity supply to the cleaner? Please check with another
electrical appliance.
Is the cyclonic dust container over-filled? Please refer to ‘Cleaner Maintenance’.
Is the filter blocked? Please refer to ‘Cleaner Maintenance’.
Is the hose or nozzle blocked? Please refer to ‘Removing a blockage from the
system’.
Has the cleaner overheated? If so, it will take approximately 30 minutes to
automatically reset.
Important Information
Hoover spares and Consumables
Always replace parts with genuine Hoover spares. These are available from your local
Hoover dealer or direct from Hoover. When ordering parts always quote your model number.
Hoover Service
Should you require service, spares and consumables at any time, please contact your
local Hoover Service Office.
Quality
Hoover’s factories have been independently assessed for quality. Our products are
made using a quality system which meets the requirements of ISO 9001
Your Guarantee
The guarantee conditions for this appliance are as defined by our representative in the
country in which it is sold. Details regarding these conditions can be obtained from the
*Certain Models Only ** Certain models only, nozzles may vary according to model
4
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising