Hoover | DDY 075-AUS | Hoover DDY 075-AUS Manuale utente

Hoover DDY 075-AUS Manuale utente
EN
User instructions
®
DDY 075
DISHWASHER
2
CONTENTS
Safety advice
Setting up, installation
Water softener unit
Loading the salt
Adjusting the upper basket
Loading the dishes
Loading the detergent
Types of detergent
Loading the rinse aid
Cleaning the filters
Some practical hints
Routine cleaning and maintenance
Description of the control panel
Technical data
Programme selection and special functions
Programme guide
Aquaprotect
Identifying minor faults
pag.
pag.
pag.
pag.
pag.
pag.
pag.
pag.
pag.
pag.
pag.
pag.
pag.
pag.
pag.
pag.
pag.
pag.
4
5
9
10
11
12
15
16
17
18
19
20
21
21
22
26
28
29
Fig. A
5
1
4
2
3
Please read the instructions in this booklet carefully because they contain important
information on how to install, use and maintain your dishwasher safely as well as
containing useful tips on how to make the most of it.
Keep this booklet safe for future reference.
3
■ The door should not be left in the open
position since this could present a potential
hazard ( es. tripping ).
SAFETY INSTRUCTIONS
There are certain basic safety rules
which are valid for any domestic
appliance.
■ Leaning or sitting on the open door of
the dishwasher could cause it to tip over.
WARNING !
Knives and other utensils with sharp
points must be loaded in the basket
with their points down or placed in a
horizontal position.
Installation
■ Make sure that the plug fitted to the
machine is compatible with the power
supply socket. If it is not, get a suitably
qualified person to fit the correct type,
and to make sure that the cables to the
mains socket are able to cope with the
power rating of the appliance.
Daily use
■ Ensure that the dishwasher does not
crush power cables.
■ This appliances is intended to be used in
household and similar applications such
as:
■ Do not use this appliance with adaptors,
power boards or extension cords.
- staff kitchen areas in shops, offices
and other working environments;
■ Should it be necessary to replace the
supply cord, call the After Sales Service
Centre.
- farm houses;
- by clients in hotels, motels and other
residential type environments;
- bed and breakfast type environments.
Safety
A different use of this appliance from
household environment or from typical
housekeeping functions, as commercial
use by expert or trained users, is excluded
even in the above applications.
■ Never touch the appliance when your
hands or feet are wet or damp.
■ Do not use when your feet are bare.
If the appliance is used in a manner
inconsistent with this it may reduce the
life of the appliance and may void the
manufacturer’s warranty.
■ Do not remove the plug from the mains
supply socket by pulling the mains cable
or the machine itself.
Any damage to the appliance or other
damage or loss arising through use that is
not consistent with domestic or household
use (even if located in a domestic or
household environment) shall not be
accepted by the manufacturer to the fullest
extent permitted by law.
■ Do not leave the appliance exposed to
the elements (rain, sun etc).
■ This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities,
or lack of experience and knowledge,
unless they have been given supervision
or instruction concerning use of the
appliance by a person responsible for
their safety.
■ The dishwasher is designed for normal
kitchen utensils.
Objects that have been contamined by
petrol, paint, traces of steel or iron,
corrosive chemicals, acids or alkalis
must not be washed in the dishwasher.
Children should be supervised to ensure
that they do not play with the appliance.
■ If there is a water softening device installed
in the home there is no need to add
salt to the water softener fitted in the
dishwasher.
■ Water left in the machine or on the
dishes at the end of the wash programme
should not be swallowed.
4
■ Cutlery is washed best if it is placed in
the basket with the handles downwards.
Disposal
■ If the appliance breaks down or stops
working properly, switch it off, turn off the
water supply and do not tamper with it.
Repair work should only be carried out
by an approved service agent and only
genuine spare parts should be fitted. Any
failure to follow the above advice may
have serious consequences for the safety
of the appliance.
■ The dishwasher has been made from
materials which can be recycled so that it
can be disposed of in an environmentally
friendly way.
■ If you wish to dispose of an old dishwasher
be careful to remove the door to
eliminate the risk of children becoming
trapped inside it.
INSTALLATION
Electrical connection
(Technical notes)
This appliance complies with international
safety standards, and is fitted with a 3 pin
plug with earth connection to ensure
complete earthing of the product.
■ After unpacking, adjust the height of the
dishwasher. For the dishwasher to work
correctly it must be level. Adjust the feet
so that the machine does not tilt by more
than 2 degrees.
Before connecting the appliance to the
mains supply it is important to ensure:
■ If it you need to move the machine after
removing the packaging, do not try to lift
it by the bottom of the door. Follow the
instructions in the figure below. Open the
door slightly and lift the machine by
holding on the top.
1. that the supply socket is properly
earthed;
2. that your electricity supply is capable of
meeting the consumption requirements
listed on the rating plate of your
appliance.
WARNING!
Ensure that your product is properly
earthed.
In the absence of adequate earthing
you will notice that when touching
the metal parts of your appliance an
electrical dispersion can be felt, due
to the presence of a radio interference
suppressor.
Manufacturer declines all responsibility
for any damage due to non-earthing of
the machine.
IMPORTANT
When the appliance is located on a
carpet floor, attention must be paid to
ensure that there is no obstruction to
the bottom vents.
Appliance
complies
with
European Directives 73/23/EEC
and 89/336/EEC, replaced by
2006/95/EC and 2004/108/EC, and
subsequent amendments.
Make sure that the plug on the
appliance remains accessible after
installation.
5
Water connection
IMPORTANT
The appliance must be connected to
the water mains using new hose-sets.
The old hose-sets should not be reused.
1
■ The inlet and drain hoses can be directed
to left or right.
IMPORTANT
The dishwasher can be connected to
either cold or hot water, as long as it
is no hotter than 60 °C.
2
■ Water pressure must be between
80 kPa and 800 kPa. If the pressure is
below the minimum consult our service
department for advice.
■ The inlet hose must be connected to a
tap so that the water supply can be cut
off when the machine is not in use
(fig. 1 B).
■ The dishwasher is fitted with 3/4" threaded
connector (fig. 2).
■ Connect inlet hose “A” to water tap “B”
with a 3/4" attachment making sure that
it has been properly tightened.
■ If it is necessary, the inlet pipe can be
lengthened up to 2,5 m. The extension
pipe is available from the After Sales
Service Centre.
3
■ If limescale deposits or sand are present
in the water, it is advisable to obtain the
appropriate filter, art. 9226085, from the
After Sales Service Centre (fig. 3). The
filter “D” must be inserted between the tap
“B” and the inlet hose “A”, remembering
to fit the washer “C”.
■ If the dishwasher is connected to new
pipes or to pipes which have not been in
use for a long time run water through for
a few minutes before connecting the
inlet hose. In this way no deposits of
sand or rust will clog up the water inflow
filter.
6
■ The hose can be hooked over the side of
the sink, but it must not be immersed in
water, in order to prevent water from
being syphoned back to the machine
when this is in operation (fig. 4Y).
Connecting the outlet hose
■ The outlet hose should disharge into a
standpipe, making sure that there are no
kinks (fig. 4).
■ When installing the appliance under a
worktop the hose pipe clamp must be
attached to the wall in the highest possible
position under the worktop (fig. 4Z).
■ The standpipe must be at least 40 cm
above floor level and it must have an
internal diameter of at least 4 cm.
■ Check that there are no kinks in the inlet
and outlet hoses.
■ It is advisable to fit an anti-odour air trap
(fig. 4X).
■ If necessary the outlet hose can be
extended up to 2,5 m, provided that it is
kept at a maximum height of 85 cm
above floor level. The extension pipe is
available from the After Sales Service
Centre.
4
7
INSTALLATION IN FITTED
KITCHENS
Underneath existing work top
(when fitting beneath a work top)
Fitting between existing cabinets
■ In most modern fitted kitchens there is
only one single work top under which
cabinets and electrical appliances are
fitted. In this case remove the work top
of the dishwasher by unscrewing the
screws under the rear edge of the top
(fig. 6a).
■ The height of the dishwasher, 85 cm, has
been designed in order to allow the
machine to be fitted between existing
cabinets of the same height in modern
fitted kitchens (fig. 5).
The feet can be adjusted so that correct
height is reached.
IMPORTANT
After removing the work top, the
screws MUST BE screwed again
under the rear edge of the top
(fig. 6b).
■ The height will then be reduced to 82 cm,
as scheduled by the International
Regulations (ISO) and the dishwasher
will fit perfectly under the kitchen
working top (fig. 7).
5
a
6
a
b
7
b
598
Opening the door
556/573
Closing the door
Put your hand into the recess and pull.
If the machine comes open while it is working,
an electrical safety device automatically
switches everything off.
Place the baskets in the machine.
Make sure that both the spray arms are
free to rotate and are not obstructed by
cutlery, crockery or pans. Close the door,
pressing on it to make sure it is firmly shut.
IMPORTANT
For the machine to work properly,
the door should not be opened while
it is in operation.
8
WATER SOFTENER UNIT
* The softener unit is set in the factory
at level 4 (d4) as this satisfies the
requirements of the majority of users.
Depending on the source of the supply,
water contains varying amounts of limestone
and minerals which are deposited on the
dishes leaving whitish stains and marks.
The higher the level of these minerals
present in the water, the harder the water is.
The dishwasher is fitted with a water
softener unit which, through the use of
special regenerating salt, supplies
softened water for washing the dishes.
The degree of hardness of your water can
be obtained from your water supply
company.
Regulate the setting of your water softener
unit according to the degree of hardness
of your water as follows:
IMPORTANT
The dishwasher must ALWAYS be
off before start of this procedure.
1. Hold down the "PROGRAMME
SELECTION" button and at the same
time switch on the dishwasher by
pressing the "ON/OFF" button (a brief
audible signal will sound).
Regulating the water softener
The water softener can treat water with a
hardness level of up to 90°fH (French
grading) or 50°dH (German grading)
through 8 settings.
2. Keep the "PROGRAMME SELECTION"
button pressed for at least 5 seconds,
UNTIL a brief audible signal sounds.
The current water softener setting level
will be shown on the display.
°fH
(French)
°dH
(German)
0
1
2
3
*4
5
6
7
0-5
6-10
11-20
21-30
31-40
41-50
51-60
61-90
0-3
4-6
7-11
12-16
17-22
23-27
28-33
34-50
Water
softener
setting
Level
Water
hardness
Use of
regenerating
salt
The settings are listed in the table below:
NO
YES
YES
YES
YES
YES
YES
YES
d0
d1
d2
d3
d4
d5
d6
d7
3. Press the same button again to select
the required water softener level: each
time the button is pressed, the setting
will increase by one level. When you
have reached "d7", the display will go
back to "d0".
4. Turn off the dishwasher by pressing the
"ON/OFF" button to confirm the new
setting.
WARNING!
If any problem occurs, turn the
dishwasher off by pressing the
"ON/OFF" button and start the
procedure again from the beginning
(STEP 1).
Digital display
“ON/OFF”
button
“PROGRAMME SELECTION” button
9
LOADING THE SALT
IMPORTANT
(Only for first start up)
When the appliance is used for the
first time, after completely filling the
salt container, it is necessary to add
water until the container overflows.
■ On the bottom of the machine there is a
container for the salt for regenerating
the softener.
■ It is important to use only a salt that is
specifically designed for dishwasher.
Other types of salt contain small quantities
of insoluble particles which over a long
period of time may affect and deteriorate
the softener performance.
■ To add salt, unscrew the cap of the container on the bottom and then refill the
container.
■ During this operation a little water will
overflow; but keep adding salt until the
container is full. When the container is
full, clean the thread of salt residue and
retighten the tap.
Salt loading indicator
This model is provided with an indicator light
on the control panel which will light up
when it is necessary to reload the salt
container.
■ After loading the salt, it is recommended
running a complete washing cycle,
or COLD RINSE programme. The salt
dispenser has a capacity of between 1.5
and 1.8 kg and, for efficient use of the
appliance, it should be refilled from time
to time according to the regulation of the
water softener unit.
IMPORTANT
The appearance of white stains on
dishes is generally an important
sign that the salt container needs
filling.
10
ADJUSTMENT OF THE
UPPER BASKET
If 29 cm to 32,5 cm plates are normally
used, load them onto the lower basket after
the upper basket has been placed in its
upper position and proceed as detailed
below:
A
1. Turn the front stops “A” outwards;
2. Take out the basket and remount it in the
upper position;
3. Replace the blocks “A” in their original
position.
A
Dishes that are bigger than 20 cm in
diameter can no longer be loaded onto the
upper basket and the mobile supports
cannot be used when the basket is in the
upper position.
11
A standard daily load is represented in
figs. 1, 2 and 3.
LOADING DISHES
Using the upper basket
Upper basket (fig. 1)
A = soup plates
B = dinner plates
C = dessert plates
D = saucers
E = cups
F = glasses
■ The upper basket is provided with
mobile racks hooked to the sides of the
basket, which can be regulated into 4
positions.
■ In the lowered position (A-A1) the racks
may be used for such items as: tea and
coffee cups, kitchen knives and ladles.
Also glasses with stems may be safely
hung on the ends of the racks.
A
1
A1
B
D
■ In the upright position (B-B1) the racks
allow you to load dinner plates and soup
plates. Plates should be loaded
vertically with the underside of the plate
towards the back of the dishwasher with
a space between each plate to allow
water to pass freely.
B
F
Upper basket (fig. 2)
A = soup plates
B = dinner plates
C = dessert plates
D = saucers
E = cups
F = glasses with stems
G = glass
H = cutlery basket
B1
■ It is advisable to load large plates
(approx. 26 or more cm) slightly tilted
towards the rear to facilitate introduction
of the basket into the machine.
2
B
A
■ Salad bowls and plastic bowls may also
be loaded on the upper basket. It is
advisable to block these in place so that
the jets of water do not make them
overturn.
■ The upper basket has been designed to
offer maximum flexibility in use and can
be loaded with up to 24 plates on two
rows, up to 30 glasses on five rows or a
mixed load.
E
C
A
H
12
C
D F
E
F
G
- POSITION “B”: for dishes which,
although standard size, have a particular
shape (very deep bowls, square dishes
or ones without borders etc.).
Upper basket (fig. 3)
A = glasses
B = saucers
C = cups
D = small bowl
E = medium bowl
F = large bowl
G = dessert plate
H = serving spoons
I = ladle
L = cutlery
3
- POSITION “C”: for larger than average
flat plates and/or ones with nonstandard shapes (square, hexagonal,
oval, pizza dishes etc.).
4
I
L
F
C
B
A
G
C D
E
C
5
B
C
A
H
A
H
■ The small plates, as those used for
desserts for example, must be placed in
the lower basket as shown in the figure 6,
with the support flap placed outwards ("B").
For normal or large plates the flap must
be in the position ("A").
Using the lower basket
■ Saucepans, oven dishes, tureens, salad
bowls, lids, serving dishes, dinner
plates, soup plates and ladles can be
loaded on the lower basket.
6
■ Place the cutlery in the plastic cutlery
holder with the handles pointing
upwards.
■ Place the cutlery holder on the lower
basket (fig. 7 and 8), making sure that
the cutlery does not get in the way of the
rotating arms.
A
■ The lower basket is fitted with a special
adjustable central rack (fig. 4 and 5).
This permits stable and optimum
loading, even when the size and/or
shape of the dishes is non-standard.
B
WARNING!
If the small plates are placed in the
basket with the support flap in the
incorrect position, the plates will
interfere with the lower spraying arm
preventing it to rotate.
- POSITION “A”: for a standard load, or
one that excludes pans, salad bowls and
the like.
13
Please load the dishwasher sensibly to
ensure the best wash results.
A standard daily load is represented in
figs. 7 and 8.
Lower basket (fig. 7)
A = medium-sized saucepan
B = large saucepan
C = frying pan
D = tureens, serving dishes
E = cutlery
F = oven dishes
G = medium bowl
H = small bowl
IMPORTANT
The lower basket has a safety-stop
device, for its safe extraction, also
especially useful with a full load.
For loading salt, cleaning filter and for
ordinary maintenance, the complete
extraction of the basket is necessary.
7
B
A
F
Cutlery basket (fig. 9)
The top of cutlery basket can be removed,
for enable various loading options.
C
G
D
E
H
9
Lower basket (fig. 8)
A = soup plates
B = dinner plates
C = dessert plates
D = serving dish
E = cutlery
8
D
B
A
C
C
E
14
LOADING THE DETERGENT
The detergent
IMPORTANT
It is essential to use a detergent
that is specifically designed for
dishwashers either in powder, liquid
or tablet form.
B
After pouring the detergent into the container,
close the lid, firstly pushing (1) and then
pressing on it (2) until you hear the click.
Unsuitable detergents (like those for
washing up by hand) do not contain the
proper ingredients for use in a dishwasher,
and stop the dishwasher from working
correctly.
Filling the detergent container
The detergent container is inside the door
(fig. A “2”). If the lid of the container is
closed, press the button (A) to open.
At the end of every wash cycle the lid is
always open and ready for the next time
the dishwasher is used.
Since not all detergents are the same the
instructions on the boxes of detergent can
vary. We should just like to remind users
that too little detergent does not clean the
dishes properly whilst too much detergent
will not produce better results and is also a
waste.
WARNING!
When loading the lower basket, please
ensure that the plates or others do not
obstruct the detergent dispenser.
The amount of detergent to be used varies
according to how dirty the dishes are and
on the type of dishes to be washed.
We advise using 20÷30 g of detergent in the
wash section of detergent compartment (B).
IMPORTANT
Do not use an excessive amount of
detergent and help limit damage to
the environment at the same time.
A
15
If when using this type of product, you
don't get satisfactory washing results,
please
contact
the
detergent
manufacturer.
TYPES OF DETERGENT
Detergent tablets
Detergent tablets of different manufacturers
dissolve at different speeds, for this
reason, during short programmes, some
detergent tablets may be not fully effective,
because they are not completely dissolved.
If these products are used, is recommended
to choose longer programmes to guarantee
the complete use of the detergent.
In certain circumstances use of combined
detergents can cause:
■ limescale deposits on dishes or in the
dishwasher;
■ a reduction in washing and drying
performance.
IMPORTANT
To get satisfactory washing results,
the tablets MUST be placed in the
wash section of the detergent
container and NOT directly in the tub.
IMPORTANT
Any problems which arise as a direct
result of the use of these products
are not covered by our warranty.
Concentrated detergents
Please note that using the "ALL in 1"
combined detergents, the rinse aid and
salt indicator lights (only used on
selected models) are superfluous, so you
must ignore the lights.
The concentrated detergents, with reduced
alkalinity and with natural enzymes, in
conjunction with 50°C wash programmes,
have a smaller impact on the environment
and they protect the dishes and the
dishwasher. The 50°C wash programmes
purposely exploit the dirt-dissolving properties
of the enzymes, allowing therefore, with the
use of the concentrated detergents, to achieve
the same results of the 65°C programmes but
at a lower temperature.
If washing and/or drying problems occur,
we recommend you return to use traditional
separate products (salt, detergent and
rinse agent). This will ensure that the water
softener in the dishwasher operates
correctly.
Combined detergents
In this case, we recommends that you:
The detergents that also contain the rinse
aid must be placed in the wash section of
the detergent container. The rinse aid
container must be empty (if it is not empty,
set the rinse aid regulator to lowest position
before using combined detergents).
■ refill both the salt and rinse aid container;
■ run one normal washing cycle without a
load.
"ALL in 1" combined detergents
Please note that on return to the use of
conventional salt, a number of cycles will
be required before the system becomes
fully efficient again.
If you are planning to use “ALL in 1” (“3 in 1 “/
“4 in 1”/ “5 in 1”, etc.) combined detergents i.e.
those with built in salt and/or rinse agent,
we would advise the following:
WARNING!
Some dishwasher detergents are
strongly alkaline. They can be extremely dangerous if swallowed. Avoid
contact with the skin and eyes and
keep children away from the dishwasher when the door is open. Check
that the detergent receptacle is empty
after completion of the wash cycle.
■ read carefully and follow the manufacturer’s
instructions given on the packaging;
■ the effectiveness of detergents containing
the built in water softener/salt depends
on the hardness of your water supply.
Check that the hardness of your water
supply is within the effective range given
on the detergent packaging.
16
LOADING THE RINSE AID
The rinse aid
The rinse aid, which is automatically
released during the last rinsing cycle, helps
the dishes to dry quickly and prevents
spots and stains forming.
Filling the rinse aid container
C
The rinse aid container can be found to the
left of the detergent container (fig. A "3").
To open the lid, push the reference mark
and, in the same time, pull the tab of
opening.
It is always advisable to use rinse aid that
is specifically designed for dishwasher.
Check the rinse aid level through the
indicator eye (C) which is located on the
dispenser.
FULL
EMPTY
dark
light
Regulating the rinse aid from 1 to 6
The regulator (D) is placed under the lid
and can be turned using a coin.
The recommended position is 4.
The limestone content of the water
considerably affects the formation of
limescale and the drying performance.
It is therefore important to regulate the
quantity of rinse aid to achieve good
washing results.
If, after the wash, streaks occur on the
dishes, decrease the amount by one
position. If whitish spots occur, increase the
amount by one position.
D
17
CLEANING THE FILTERS
The filter system (fig.A “4”) consists of:
1
a central container that traps the larger
particles;
a flat gauze that continuously filters the
wash water;
a micro filter, located beneath the gauze,
that traps the tiniest particles ensuring a
perfect rinse.
■ To achieve excellent results every time,
the filters should be checked and
cleaned after each wash.
■ To remove the filter unit, simply turn the
handle anticlockwise (fig. 1).
2
■ For ease of cleaning, the central container
is removable (fig. 2).
■ Remove the gauze filter (fig.3) and
wash the whole unit under a jet of
water. If necessary a small brush can
be used.
■ With the Self-cleaning Micro filter,
maintenance is reduced and the filter
unit need only be checked every two
weeks. Nevertheless, after each wash it
is advisable to check that the central
container and the gauze filter are not
clogged.
WARNING!
After cleaning the filters, make sure
that they are correctly reassembled
and that the gauze filter is properly
positioned at the bottom of the
dishwasher.
3
Make sure that the filter is screwed
back, clockwise, into the gauze, as
poor seating of the filter unit could
have an adverse effect on the
efficiency of the appliance.
IMPORTANT
Never use the dishwasher without
the filters.
18
PRATICAL HINTS
How to make savings
■ If you want the dishwasher to give a
complete wash, place the dishes in the
dishwasher at the end of each meal and
if necessary turn on the COLD RINSE
cycle to soften the food remains and
remove bigger particles of food from the
new load of dishes.
When the dishwasher is full start the
complete wash cycle programme.
How to get really good wash
results
■ Before placing the dishes in the
dishwasher, remove any remaining
food (bones, shells, pieces of meat or
vegetables, coffee grounds, skin of fruit,
cigarette ash, tooth picks etc. to avoid
blocking the filters, water outlet and
washing arm nozzles.
■ If the dishes are not very dirty or if the
baskets are not very full select an
ECONOMY programme, following the
instructions in the program list.
■ Try not to rinse the dishes before
loading them into the dishwasher.
■ If saucepans and oven dishes are
encrusted with the remains of burnt or
roast food, it is advisable to leave them
to soak before washing.
What not to wash
■ It should be remembered that not all
dishes are suitable for washing in a
dishwasher.We advise against using
the dishwasher to wash items in
thermoplastic, cutlery with wooden or
plastic handles, saucepans with
wooden handles, items in aluminium,
crystal, leaded glass unless otherwise
stated.
■ Place the dishes face downwards.
■ Try to place the dishes in such a way
that they are not touching one another.
If they are loaded properly you will get
better results.
■ After loading the dishes check that the
washing arms can rotate freely.
■ Certain decorations may fade. It is
therefore a good idea before loading the
whole batch to wash just one of the
items first so as to be sure that others
like it will not fade.
■ Pans and other dishes that have
particularly stubborn food particles or
remnants of burnt food should be left to
soak in water with dishwasher
detergent.
■ It is a good idea not to put silver cutlery
with non-stainless steel handles into
the dishwasher as there could be a
chemical reaction between them.
■ To wash silver properly:
a) rinse the silver immediately after
use, especially if it has been used for
mayonnaise, eggs, fish etc.;
IMPORTANT
When buying new crockery or
cutlery always make sure that they are
suitable for washing in a dishwasher.
b) do not sprinkle detergent onto it;
c) keep it separate from other metals.
Useful hints
■ In order to avoid any dripping from the
top rack, remove the lower rack first.
■ If the dishes are to be left in the
machine for some time, leave the door
ajar, to let some air circulate and to
improve the drying performance.
19
CLEANING AND
MAINTENANCE
1
1b
■ To clean the dishwasher outside, do not
use solvents (degreasing action) neither
abrasives, but only a cloth soaked with
water.
■ The dishwasher does not require special
maintenance, because the tank is
self-cleaning.
■ Regularly wipe the door gasket with a
damp cloth to remove any food remains
or rinse aid.
2
■ It is advisable to remove limestone
deposits or dirt periodically, by doing an
empty wash; pour a glass of vinegar on
the bottom of the tank and select the
light wash.
■ If, in spite of the routine cleaning of the
filters, you notice that the dishes or pans
are not properly washed or rinsed, check
that all the spray heads on the rotor
arms (fig. A “5”) are clear.
If they are blocked, clean them in the
following way:
WHEN CYCLE IS FINISHED
1. to remove the upper rotor arm, turn it
until it lines up with the stop marked
by the arrow (fig. 1). Push it upwards
(fig. 1b) and, keeping it pushed in,
unscrew it in a clockwise direction
(to reassemble it repeat the same
operation, but turn it anticlockwise).
The lower rotor arm can be removed
simply by pulling it upwards (fig. 2);
After every wash it is essential to turn off
water supply and to switch off the machine
by pressing the On/Off button to the off
position.
2. wash the rotor arms under a jet of water
to clear any blockage in the spray
heads;
1. do an empty wash with detergent in order
to clean the machine of any deposits;
If the machine is not going to be used for
some time, it is advisable to follow these
rules:
2. pull out the electric plug;
3. when you have finished, refit the rotor
arms in the same position, remembering
to re-align the arrow and screw into
position.
3. turn off the water tap;
4. fill the rinse aid container;
5. Ieave the door ajar;
■ Both the door lining and the tank lining
are in stainless steel; however, should
spots caused by oxidation occur, this is
probably due to a high level of iron salts
presents in the water.
6. keep the inside of the machine clean;
7. If the machine is left in places where the
temperature is below 0°C any water left
inside the pipes may freeze. Wait until
the temperature rises above zero and
then wait for about 24 hours before
starting up the dishwasher.
■ The spots can be removed with a mild
abrasive agent; never use chlorine
based materials, steel wool, etc.
20
DESCRIPTION OF THE CONTROL PANEL
A
B
C
D
"ON/OFF" button
E
F
G
"SUPER ECO" option button
"PROGRAMME SELECTION" button
"DELAY START" button
"START"/"RESET" button
(start/cancelling programme)
"ALL IN 1" option button
H
I
L
M
N
O
DIGITAL DISPLAY
"SALT EMPTY" light
"RINSE AID EMPTY" light
"OPTION SELECTION" lights
"ACTION PRO" lights
Programme guide
"ACTION PRO" button
DIMENSIONS:
Height
Depth
Width
Depth with door open
with working top
without working top
85
60
60
120
82
57,3
59,8
117
cm
cm
cm
cm
TECHNICAL DATA:
EN 50242 place load
Capacity with pans and dishes
Water supply pressure
Fuse
Power input
Supply voltage
15
9 persons
Min. 80 kPa - Max 800 kPa
(see rating plate)
(see rating plate)
(see rating plate)
21
PROGRAMME SELECTION
AND SPECIAL FUNCTIONS
■ Press the "START" button.
The length of the program will be shown on
the display alternating hours with
minutes [I.e: 1 h (1 hour) / 25 (25 minutes)].
(Use in conjunction with programme guide)
■ When the door is shut, after an audible
signal has sounded, the programme will
start automatically. The display will show
the time remaining to the end of the cycle.
"ACTION PRO" button
This button allows you to modify the wash
intensity, according to how dirty your dishes
are, by modifying the wash time and
temperature.
Press the button to increase the intensity of
wash cycle (
indicator light) or to reduce
the intensity of wash, this also allows you to
decrease the wash length time (
indicator
light).
The combination of the button with the 4
main wash programmes enables to have 8
additional wash cycles (achieving a total of
12 programmes of washing).
WITHIN one minute of the programme
commencing, another programme
can be selected, simply by pressing
the "PROGRAMME SELECTION"
button (it is also possible to change
the "ACTION PRO" button setting ).
Programme interruption
Opening the door when a programme is
running is not recommended especially during
the main wash and final hot rinse phases.
However, if the door is opened while a
programme is running (for example, to add
dishes) the machine stops automatically and
the display will flash the remaining time
before the end of the cycle. Close the door,
without pressing any buttons. The cycle will
start from where it left off.
IMPORTANT
When the dishwasher is switched on,
the setting last used will be indicated.
Programme settings
■ Open the door and place the dirty dishes
inside the appliance.
■ Press the "ON/OFF" button
display will show two lines.
. The
IMPORTANT
A running program can be interrupted
without opening the door by
pressing the "ON/OFF" button. In
this case, simply press the "ON/OFF"
button again to restart the cycle from
where it left off.
■ Choose a programme by pressing the
"PROGRAMME SELECTION" button.
■ If you wish, press the "ACTION PRO"
button.
■ If you wish to select an option, press the
corresponding button (the indicator light
will turn on).
WARNING!
If you open the door during the
drying cycle, an audible audio signal
advises you that the drying cycle has
not yet finished.
The option buttons can be selected or
deselected WHITIN one minute of the
programme commencing.
22
soil washes, and for slightly wet dishes that
are not fully dry, & improved drying results.
We advise you to leave the door of the
Dishwasher half-open at the end of the
cycle, to allow for a natural circulation of air
inside the dishwasher.
Changing a running programme
Proceed as follows to change or cancel a
running program:
■ Hold the "RESET" button down for at
least 5 seconds. "00" will appear on the
display and some audible signals will
sound.
"ALL IN 1" button
This option optimises the use of "ALL in 1"
("3 in 1"/"4 in 1"/"5 in 1", ecc.) combined
detergents.
By pressing this button, the selected
washing programme is modified to get best
performance from combined detergents
(furthermore, the salt and rinse aid
shortage lights are de-activated).
■ The running programme will be cancelled.
The display will show two lines.
■ At this point a new programme can be set.
WARNING!
Before starting a new programme,
you should check that there is still
detergent in the dispenser.
If necessary, top up the dispenser.
WARNING!
Once selected, this option keeps
being on (light on) also for next
washing cycles and it can be de-activate
(light off) only by pressing the button
once again.
Programme operations
Whilst a programme is running, the display
shows the time remaining to the end of the
cycle, which is automatically updated.
IMPORTANT
When this option is selected, the
"RAPID" cycle is 10 minutes longer.
If there is any break in the power supply
while the dishwasher is operating, a
special memory stores the selected
programme and, when the power is
restored, it continues where it left off.
"DELAY START" button
Programme end
Dishwasher start time can be set with this
button, delaying start from 1 to 23 hours.
A 5 second alarm will sound (if not muted)
3 times at 30 second intervals to signal that
the programme has ended.
The display and all the indicator lights will
switch off.
Dishes can now be removed and the
dishwasher turned off by pressing the
"ON/OFF" button or dishes can be loaded
for new cycle.
Proceed as follows to set a delayed start:
■ Press the "DELAY START" button ("00"
will appear on the display).
Option buttons
■ Press the button again to increase the
delay in hours (each time the button is
pressed the delay is increased by 1 hour
to a maximum of 23).
"SUPER ECO" button
This button provides an energy and time
saving of 25% on average (according to
the select cycle) reducing the wash water
temperature and the drying time during the
final rinse.
This programme is recommended for light
23
■ To start the countdown, press the
"START" button.
The display will show the time remaining
to the begin of the programme.
At the end of the countdown, the programme
will automatically start and the length of the
selected cycle will be shown in the display.
Memorization of the last
programme used
The last programme used can
memorized by following the below:
Proceed as follows to cancel a delayed
start:
be
■ Hold the "RESET" button down for at
least 5 seconds. "00" will appear on the
display and some audible signals will
sound.
IMPORTANT
The dishwasher must ALWAYS be off
before start of this procedure.
■ The delayed start and the selected
programme will be cancelled.
The display will show two lines.
1. Hold down the "PROGRAMME
SELECTION" button and at the same
time
switch on the dishwasher by
pressing the "ON/OFF" button (a brief
audible signal will sound).
■ At this point, a new programme and
option buttons must be set to start a
new programme as indicated in the
"PROGRAMME SETTINGS" section.
2. Keep the "PROGRAMME SELECTION"
button pressed for at least 30 seconds
(during this time, 3 audible signals will
sound).
Alarm mute for the PROGRAMME
END
3. Release the button when the THIRD
audible signal sounds ("A0 " will appear
on the display to indicate that the
memorization is off).
The alarm for the programme end may be
muted as follows:
4. Press the same button again ("A1" will
appear on the display to indicate that the
memorization is on).
IMPORTANT
The dishwasher must ALWAYS be
off before start of this procedure.
5. Turn off the dishwasher by pressing the
"ON/OFF" button to confirm the new
setting.
1. Hold down the "PROGRAMME
SELECTION" button and at the same
time switch on the dishwasher by
pressing the "ON/OFF" button (a brief
audible signal will sound).
To disable the memorization, follow the
same procedure.
2. Keep the "PROGRAMME SELECTION"
button pressed for at least 15 seconds
(during this time 2 audible signals will
sound).
IMPORTANT
This dishwasher is equipped with an
anti-overflow safety device which will
automatically discharge any excess
water should a problem occur.
3. Release the button when the second
audible signal sounds ("b1" will appear
on the display to indicate that the alarm
is on).
WARNING!
To ensure the correct operation of
the anti-overflow safety device, we
recommend that the dishwasher is
not moved or tilted during operation.
If however it is necessary to tilt or
move the dishwasher, please ensure
that the washing cycle is complete
and that there is no remaining water
inside the dishwasher.
4. Press the same button again ("b0" will
appear on the display to indicate that the
alarm is off).
5. Turn off the dishwasher by pressing the
"ON/OFF" button to confirm the new
setting.
To turn the alarm on again, follow the same
procedure.
24
The dishwasher is able to signal a series of faults in the display.
AUTOMATIC FAULT SIGNALS
FAULTS
CAUSE
SOLUTION
E2 appears on the display and
the alarm sounds.
No water (inlet hose closed).
Turn off the dishwasher, open the
inlet hose and reset the cycle.
E3 appears on the display and
the alarm sounds.
The machine cannot drain water.
Check if the drain tube is bent or if
the siphon or filters are clogged.
If the problem persists, contact
Customer Service.
E4 appears on the display and
the alarm sounds.
Water leak
Check if the drain tube is bent or if
the siphon or filters are clogged.
If the problem persists, contact
Customer Service.
E5,E6,E7,Ef or EL appears
on the display and the alarm
sounds.
Electronic control fault.
Contact Customer Service.
E8 or Ei appear on the display
and the alarm sounds.
The water heating element is not
working correctly or the filter plate is
clogged.
Clean the filter plate.
If the problem persists, contact
Customer Service.
25
PROGRAMME GUIDE
Wash with prewash
For wash programmes with prewash, it is advisable to add a second dose of detergent (max.
5.75 g) directly in the machine.
Programme
Description
Hygiene+
75°C
An antibacterial cycle, intended for washing and
sterilising dishes (even heavily stained ones)
babies’ bottles etc.
INTENSIVE
75°C
Once a day - for heavily soiled pans and any
other items that have been left all day for
washing.
Chef
65°C
Intended for rapid washing of heavily soiled
crockery and cutlery.
Family
70°C
For mixed loads with pots and pans including
some heavy soiled items of crockery and cutlery.
UNIVERSAL
60°C
Intended mixed soiled loads including heavy
soiled items of crockery, glassware and cutlery.
Daily
55°C
Fast cycle for mixed lightly soiled loads of
crockery, glassware, cutlery, pots and pans.
ECO plus
55°C
A medium temperature programme, intended for
washing pans and dishes that are “normally” dirty,
using detergents which contain enzymes.
ECO
45°C
Energy saving program intended for normal
soiled loads of crockery, glassware and cutlery.
Programme for testing to AS/NZS 2007.
Cristal
45°C
Suitable for delicate crockery and glassware.
A Wash 59’
65°C
Suitable for heavily soiled items that are to be
washed straight after a meal (Max 8 place load).
RAPID 29'
50°C
Quick wash for dishes which are to be washed
immediately after the meal (Max 6 place load).
Pre-wash
Short cold pre-wash for items that are stored in
the dishwasher until you are ready to wash a full
load.
26
75°C
140
YES YES YES
75°C
135
YES YES YES
(28 g)
(5.75 g)
(28 g)
65°C
85
YES YES YES
(0 g)
(28 g)
70°C
125
YES YES YES
(0 g)
(28 g)
60°C
120
YES YES YES
55°C
80
YES YES YES
(0 g)
(28 g)
(0 g)
(28 g)
55°C
190
YES YES YES
(5.75 g)
(28 g)
45°C
170
YES YES YES
(0 g)
(28 g)
45°C
85
YES YES YES
(5.75 g)
(28 g)
65°C
59
YES YES YES
(0 g)
(28 g)
50°C
29
YES
N/A YES
5
YES
N/A
*
(0 g)
N/A = OPTION NOT AVAILABLE
WITH HOT WATER THE TIME REMAINING UNTIL THE END OF THE PROGRAMME IS AUTOMATICALLY DISPLAYED WHILE THE
PROGRAMME IS RUNNING.
"ALL IN 1" button
“SUPER ECO” button
"DELAY START" button
*
With cold water (15°C)
-Tolerance ± 10%-
Hot rinse with rinse aid
Second cold rinse
First cold rinse
Main wash
Special function
buttons
available
(28 g)
(5.75 g)
(0 g)
Cold pre-wash
Hot pre-wash
Check salt container
Check rinse aid
dispenser
Clean filter
Detergent for washing
Detergent for soaking
(Prewash)
•••••
•••••
•••••
••••
••••
••••
••••
•••••
••••
•••••
••••
•
(5.75 g)
Avarage
duration
in minutes
Programme contents
Check list
27
AQUAPROTECT – PROTECTED INCOMING WATER PIPE
The main inlet pipe is contained within a protective transparent hose. In the event of
damage occurring to the main inlet pipe any water leakage is retained within the
transparent hose.
If water has leaked from the main inlet pipe there will be a visible sign within the
transparent hose.
You may continue to complete the programme cycle but for safety we recommend
the immediate replacement of the complete hose assembly.
If the hose is not long enough for correct connection, it must be replaced with a
longer one.
The hose can be obtained from a Service Centre.
Protective
transparent
hose
Main inlet
pipe
28
IDENTIFYING MINOR FAULTS
Should the dishwasher fail to operate, before contacting the Service Centre, make
the following checks:
FAULT
1 - Machine completely dead
2 - Machine does not
draw water
3 - Machine does not
discharge water
4 - Machine discharges
water continuously
5 - Spray arms are not heard
to rotate
6 - On electronic appliances
without a display: one or
more LED flashing quickly.
CAUSE
REMEDY
Plug is not connected to wall
socket
Connect electric plug
O/I button has not been pressed
Press button
Door is open
Close door
No electricity
Check the fuse in the plug and
the electricity supply
See causes for no. 1
Check
Water tap is turned off
Turn water tap on
Programme selector is not at
correct position
Turn programme selector to
correct position
The inlet hose is bent
Eliminate the bends in the hose
The inlet hose filter is not
correctly connected
Clean the filter at the end of the
hose
Filter is dirty
Clean filter
Outlet hose is kinked
Straighten outlet hose
The outlet hose extension is
not correctly connected
Follow the instructions for
connecting the outlet hose
carefully
The outlet connection on the
wall is pointing downwards not
upwards
Call a qualified technician
Position of outlet hose is too
low
Lift outlet hose to at least 40 cm
above floor level
Excessive amount of detergent
Reduce amount of detergent
Use suitable detergent
Item prevents arms from rotating
Check
Plate and cup filter very dirty
Clean plate and cup filter
Water inlet tap turned off
Switch off the appliance.
Turn on the tap.
Re-set the cycle.
29
FAULT
CAUSE
See causes for no. 5
REMEDY
Check
Bottom of saucepans have not Burnt on food remains must
been washed well
be soaked before putting pans
in dishwasher
7 - Load of dishes is only
partially washed
Edge of saucepans have not
been washed well
Reposition saucepans
Spray arms are partially blocked
Remove spray arms by
unscrewing ring nuts clockwise
and wash under running water
The dishes have not been
properly loaded
Do not place the dishes too
closely together
The end of the outlet hose is in
the water
The end of the outlet hose
must not come into contact
with the outflow water
The incorrect amount of
Increase the measure
detergent has been measured
according to how dirty the
out; the detergent is old and hard dishes are and change detergent
The wash programme is not
thorough enough
Choose a more vigorous
programme
The lower basket dishes have
not been washed
Depress half load button
8 - Detergent not dispensed
or partially dispensed
Cutlery, dishes, pans, etc... stop Position dishes not to obstruct
the detergent dispenser opening the dispenser
9 - Presence of white spots
on dishes
Water is too hard
10 - Noise during wash
The dishes knock against one Re-check loading of dishes in
another
the basket
Check salt and rinse aid level
and regulate amount.
Should the fault persist,
Contact Service Centre
The revolving arms knock against Again re-check loading
the dishes
11 - The dishes are not
completely dry
Inadequate air flow
Leave the dishwasher door ajar
at the end of the wash program
to allow the dishes to dry naturally
Rinse aid missing
Fill the rinse aid dispenser
N.B.: Should any of the situations occur and should the machine give a bad wash performance,
it is necessary to remove the deposits from the dishes by hand since the final drying cycle hardens the
deposits which a second wash in the machine would not be able to remove.
If the malfunction continues contact a Service Centre quoting the serial number of the dishwasher.
This is found on the plaque on the inside of the dishwasher door at the top or on the guarantee.
This information will make it possible to take more effective action more quickly.
The manufacturers decline any responsibility for any printing mistakes in this instruction booklet.
They also reserve the right to modify their own appliances as necessary without altering the
essential characteristics.
30
The manufacturer declines all responsibility in the event of any printing mistakes in this
booklet. The manufacturer also reserves the right to make appropriate modifications to
its products without changing the essential characteristics.
This appliance is marked according to the European directive 2002/96/EC on Waste Electrical and Electronic
Equipment (WEEE).
By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the
environment and human health, which could otherwise be caused by inappropriate waste handling of this
product.
The symbol on the product indicates that this product may not be treated as household waste. Instead it shall
be handed over to the applicable collection point for the recycling of electrical and electronic equipment
Disposal must be carried out in accordance with local environmental regulations for waste disposal.
For more detailed information about treatment, recovery and recycling of this product, please contact your local
city office, your household waste disposal service or the shop where you purchased the product.
13.02 - 41901100
EN
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising