Hoover | CJ930T/1 001 | Hoover CJ930T/1 001 User manual

Hoover CJ930T/1 001 User manual
USER MANUAL
INSTRUCTIONS FOR SAFE USE
INSTRUCTIONS FOR SAFE USE
Do not spray with or pick up flammable liquids, cleaning
fluids, aerosols or their vapours.
This appliance should only be used for domestic cleaning,
as described in this user guide. Please ensure that this guide
is fully understood before operating the appliance.
Do not run over the power cord when using your appliance
or remove the plug by pulling on the power cord.
Do not leave the appliance plugged in. Always switch off
and remove the plug from the socket after use, or before
cleaning the appliance or any maintenance task.
Do not continue to use your appliance if it appears faulty.
Hoover service: To ensure the continued safe and efficient
operation of this appliance we recommend that any servicing
or repairs are only carried out by an authorised Hoover
service engineer.
This appliance can be used by children aged from 8 years
and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the
hazards involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by
children without supervision.
Do not stand on or wrap the cord around arms or legs when
using your appliance.
Do not use the appliance to clean animals or people.
Do not position the appliance above you when cleaning the
stairs.
If the power cord is damaged stop using the appliance
immediately. To avoid a safety hazard, an authorised Hoover
service engineer must replace the power cord.
Do not touch the plug or appliance with wet hands.
For UK and Ireland only: This appliance has a 13 Amp mains
plug. If you need to change the fuse in the mains plug, use
a 13Amp ASTA (BS1362) fuse.
Keep hands, feet, loose clothing and hair away from
rotating brushes.
Use only attachments, consumables or spares
recommended or supplied by Hoover.
Static electricity: some carpets can cause a small build up
of static electricity. Any static discharge is not hazardous to
health.
Do not use your appliance out of doors.
Do not pick up hard or sharp objects, matches, hot ashes,
cigarette ends or other similar items.
-1-
GB
GB
GETTING TO KNOW YOUR CLEANER
HANDLE
WATER RELEASE
BUTTON
Congratulations on the purchase
of your new Hoover.
Please take the time to read this
manual carefully.
You’ll then be ready to make the
most of the special features only
the new Hoover can offer!
CORD CLIP
HANDLE RELEASE
BUTTON
CARRY HANDLE
UPPER STORAGE
HOOK
CLEAN WATER TANK
POWER CORD
INLET COVER
When first unpacking your cleaner
please check all items are included:
Cleaner body
Upholstery brush*
Flexible hose *
Hose bag*
DIRTY WATER TANK
RELEASE LEVER
LOWER STORAGE
HOOK
EXHAUST FILTER
CHAMBER
DIRTY WATER TANK
HANDLE
ON/OFF PEDAL
DIRTY WATER TANK
CLEANER RELEASE
PEDAL
UPHOLSTERY
BRUSH *
HOSE BAG*
EXHAUST
FILTER
*Certain models only
-2-
HOOVER
CARPET
CLEANING
SOLUTION
FLEXIBLE HOSE*
PREPARING YOUR CLEANER
1
Remove the contents of the packaging.
You should find the following:
BEFORE CLEANING A CARPET
2
Raise the handle to the upright position
until it locks in place.
• Cleaner body
• Upholstery brush*
• Flexible hose*
3
To fold the handle press the handle
release button and fold to the storage
position.
• Vacuum thoroughly.
• Test for colourfastness
• Move the furniture
Test for colourfastness - Wet a white absorbent cloth
with the solution. In a small, hidden area of your
carpet, gently rub the surface with the dampened
cloth.
Wait ten minutes and check for colour removal or
bleed with a white paper towel.
If your carpet has more than one colour, check all
colours.
4
Once the handle has been lowered lift
the carry handle to allow the cleaner to
be carried from room to room.
When cleaning an entire room, move furniture out of
the area to be cleaned. If the furniture is too heavy to
move, place aluminium foil or wax paper under legs.
This will prevent wood finishes from staining your
carpet. Pin up furniture skirts and curtains.
NOTE: Do not over saturate your carpet.
IMPORTANT: This cleaner
should not be used to dry
vacuum the carpet.
*Certain models only
GB
-3-
GB
FILLING THE CLEAN WATER TANK*
The clean water tank holds the water and cleaning
solution.
IMPORTANT: Always turn the cleaner off and
disconnect from the electrical outlet before filling
the clean water tank.
1
Add the required amount of cleaning fluid to
a measuring jug.
(approx. 40ml per 1L of water)
2
Mix the solution with warm water.
(Max. temperature - 40ºC)
IMPORTANT: When filling the
clean water tank, do not exceed
the max fill line.
NOTE: Before using this
appliance, please ensure
dirty water tank release
lever and inlet cover are
fully locked.
3
Press the clean water tank release latch
and remove from the cleaner.
4
Open the screw cap on the bottom of
the tank.
5
Pour the solution into the clean water
thank. Do not exceed the max fill line.
Replace the cap and return the clean
water tank to the cleaner.
WARNING: Use only Hoover carpet cleaning solution. Using other solution brands may cause excess foaming and will
prevent the cleaner from working effectively.
Using other solutions may affect your warranty
*Certain models only
-4-
GB
CLEANING CARPETS
Dry vacuum the carpet thoroughly before cleaning
your carpet.
1
Unwrap the power cord and plug the
cleaner into the power supply.
2 Press the ON/OFF pedal.
Ensure the carpet has been checked for colour
fastness.
IMPORTANT: This cleaner
should not be used to dry
vacuum the carpet.
3
Press the cleaner release pedal and recline
the cleaner.
4 Press the solution mix trigger to release
the solution.
WARNING: Use only Hoover carpet cleaning solution. Using other solution
brands may cause excess foaming and will prevent the cleaner from working
effectively. Using other solutions may affect your warranty.
*Certain models only
-5-
5 For best results apply the solution on the
forward stroke (press trigger) and recover
the solution on the backward stroke (release
trigger).
CAUTION: This product is intended for cleaning
purpose only. Do not use the main suction head or
upholstery brush to remove large spills.
USING THE UPHOLSTERY BRUSH
*
NOTE: Do not over saturate your upholstery.
NOTE: The clean water tank will need to be
filled with solution and water before use.
1
Take out the flexible hose and the
upholstery brush
5
Press trigger to release solution.
GB
2
Lift the inlet cover
3
Insert the hose connector
6
Pull upholstery brush back
over spill to pick up liquid.
7
Upholstery brush can only work with
the cleaner in the upright position
For best results apply solution
on the forward stroke and
release the trigger to recover
on the back ward stroke.
*Certain models only
-6-
4
Press the ON/OFF pedal
STORAGE
Put the flexible hose * and the upholstery brush *
back into the bag for storage.
CORD CLIP
GB
Before storing the cleaner:
Do not run over the power cord.
Turn the cleaner off and disconnect from the electrical
socket.
Clip the power cord in the cord clip at the back of the
handle to avoid accidentally running the cleaner over
the cord and causing any damage.
Empty and rinse the dirty water tank. Allow to air dry.
Press the handle release button and lower the handle
for storage.
CORD STORAGE
Turn the cleaner off and remove the plug from the
electrical socket. Wind the power cord around the cord
storage hooks.
Rotate the storage hooks to quickly release the full
length of the power cord.
Do not store the cleaner on a wood surface unless the
cleaner is completely dry.
*Certain models only
-7-
EMPTYING THE DIRTY WATER TANK
CLEANING THE EXHAUST FILTER
WARNING: DO NOT exceed the max fill line on the dirty water tank.
1
Press the dirty water tank release lever.
2
Remove the dirty water tank from the
cleaner.
Press the exhaust filter
release latch.
Remove the exhaust filter
chamber.
Remove the filter from the
chamber.
Rinse under hand warm
water to remove any
debris. Allow to completely
dry before returning to the
cleaner.
3
Turn the tank cap anti-clockwise to open.
4
Empty the tank. Rinse the tank with clean
water and allow to dry before storing the
cleaner.
CLEANING THE PRE MOTOR FILTER
Remove the dirty water
tank from the cleaner.
Take out the pre motor
filter, then clean it.
WARNING: Always switch the cleaner off and unplug it from the
electrical socket before emptying the dirty water tank.
*Certain models only
-8-
IMPORTANT: Clean the filters
after each use.
WARNING: Ensure both filter are
fitted to the cleaner before use.
GB
CLEANING THE BRUSHBAR*
Turn the cleaner upside down. Remove any
threads or debris from the brush bar.
IMPORTANT: Switch the cleaner off and
remove the plug from the electricity
supply before dismantling cleaner
CHANGING THE BRUSHBAR*
1
Press the dirty water tank release
lever and remove the dirty water
tank. Unscrew 4 retaining screws on
the top surface.
2
Turn the cleaner over. Remove
the brushbar alignment brackets.
4
Replace the brush bar and attach to the
nozzle. Attach the alignment brackets and
assemble to the cleaner.
CLEANING THE AGITATOR*
Remove any threads or debris ensuring the
agitator can rotate freely.
3
THIS FEATURE VARIES ACCORDING
TO MODEL
Please check the underside of your
cleaner and follow the appropriate
instructions.
*Certain models only
Unscrew 2 retaining screws located
on the underside of the detergent
nozzle. Remove the brushbar from
the nozzle.
THIS FEATURE VARIES ACCORDING TO MODEL
Please check the underside of your cleaner and
follow the appropriate instructions.
-9-
GB
IMPORTANT: Switch the cleaner off and remove the plug from the electricity supply
before dismantling cleaner.
CHANGING THE AGITATOR / BELT*
1
4
Turn cleaner over and remove 7
retaining screws.
Remove the agitator brackets
2
5
Remove the belt cover and safety
bar.
Replace the agitator by looping the belt
round the agitator making sure it sits
securely in the belt channel.
THIS FEATURE VARIES ACCORDING TO MODEL
Please check the underside of your cleaner and
follow the appropriate instructions.
*Certain models only
- 10 -
3
6
Slide the agitator assembly out
of the cleaner and check the belt
for wear.
Reassemble the agitator assembly to the
cleaner ensuring the agitator can rotate
freely.
GB
Troubleshooting
Hoover Service
If your cleaner is not working properly run through the following checklist.
Should you require service at any time, please contact your local Hoover Service Office.
WARNING: To reduce the risk of personal injury, unplug the carpet washer
before performing maintenance/troubleshooting checks.
Hoover spares and Consumables Always replace parts with genuine Hoover spares. These
are available from your local Hoover dealer or direct from Hoover.
When ordering parts always quote your model number.
Why won’t the carpet washer turn on?
• It may not be plugged into the electrical outlet correctly: ensure that the plug is
pushed in securely and switched on.
• The power button on the unit hasn’t been fully depressed.
• If unit cuts out during use, disconnect the unit from the wall socket, allow to
cool for one hour, clean the filter and empty the dirty water tank and check
hose, brushbar for blockages.
Why won’t the cleaner pick up solution/spills?
• The dirty water tank may be full. Empty the dirty water tank.
• Ensure the dirty water tank is fitted correctly and the tank cap is securely fitted.
• Check the brushbar for blockages.
Why won’t the solution/clean water dispense?
• The solution/clean water tank may be empty.
• Ensure dirty water tank is fitted securely.
USE ONLY HOOVER SPARES
SPARE PARTS
Hoover’s factories have been independently assessed for quality. Our products are made
using a quality system which meets the requirements of ISO 9001.
Environment
The symbol on this appliance indicates that this appliance may not be
treated as household waste. Instead it must be handed over to the applicable
collection point for the recycling of electrical and electronic equipment.
Disposal must be carried out in accordance with local environmental
regulations for waste disposal. For more detailed information about treatment, recovery
and recycling of this appliance, please contact your local city office, your household and
waste disposal service or the shop where you purchased the appliance.
This appliance complies with the European Directives 2014/35/EU, 2014/30/EU
and 2011/65/EU.
CODE
AGITATOR
Y30
35601321
FLEXIBLE HOSE
D144
35601409
UPHOLSTERY TOOL AND BRISTLES INSERT
MFT4
35601410
FILTER& BRISTLES INSERT
U70
35601411
BELT
V35
35601322
BRUSH
F4
35601324
CLEANJET SOLUTION
Quality
35601351
CANDY HOOVER GROUP S.r.l. Via Privata Eden Fumagalli, 20861 Brugherio (MB) Italy
Your Guarantee
The guarantee conditions for this appliance are as defined by our representative in the
country in which it is sold. Details regarding these conditions can be obtained from
the dealer from whom the appliance was purchased. The bill of sale or receipt must be
produced when making any claim under the terms of this guarantee.
Subject to change without notice
- 11 -
GB
© 2015
48017673/01
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising