Hoover | HF822OF 001 | Hoover HF822OF 001 User manual

Hoover HF822OF 001 User manual
INSTRUCTION MANUAL
T
S
L
A
K1
B
C
D
E
K2
K3
R
Q
P
J
K
M
O
N
V*
Z*
U
AB*
W*
AA*
X*
F
Y*
AC*
AD*
G
I
H
AF*
AG*
AE
* Certain models only, accessories may vary according to model
A
B
3PCS
1
2
A
A
B
B
C
3
4
1
2
+
5*
6
a
b
7
8
9
10
A
A
B
11
12
13
14
B
A
15
B
16
*
17
2
1
3
4
*
18
5
GB
INSTRUCTIONS FOR SAFE USE AND FITTINGS
This appliance should only be used for domestic cleaning, as
described in this user guide. Please ensure that this guide is
fully understood before operating the appliance.
Always switch off and remove the charger from the socket
before cleaning the appliance or any maintenance task.
This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by children
without supervision.
If the power cord is damaged stop using the appliance
immediately.
To avoid a safety hazard, an authorised Hoover service
engineer must replace the power cord.
Use only the original charger supplied with the appliance.
Check that your supply voltage is the same as that stated on
the charger.
This appliance is supplied with a double insulated battery
charger which is only suitable for insertion in a 230V (UK 240V)
socket outlet.
Plug the charger in to suitable socket outlet and connect the
charger jack plug to the appliance.
When charging the appliance, the power switch lever must be
in the off position.
Before first use, charge your appliance for at least 24 hours.
The battery pack LED light will blink in blue when charging and
remain lit when fully charged.
Re-connect the appliance to the charger after use to recharge
the battery.
Never charge the batteries in temperatures above 37°C or
below 0°C. It is normal for the charger to become warm to
the touch when charging. Unplug the charger in the event of
prolonged absence (holidays, etc.). Recharge appliance again
before use as batteries may self discharge over increased
periods of storage.
Use only attachments, consumables or spares recommended
or supplied by Hoover.
1
GB
Static electricity: some carpets can cause a small build up
of static electricity. Any static discharge is not hazardous to
health.
Keep hands, feet, loose clothing and hair away from rotating
brushes.
Do not unplug the charger by pulling on the power cord.
Do not use your appliance out of doors or on any wet surface or
for wet pick up. Do not pick up hard or sharp objects, matches,
hot ashes, cigarette ends or other similar items. Do not spray
with or pick up flammable liquids, cleaning fluids, aerosols or
their vapours. Do not run over the power cord when using your
appliance or remove the plug by pulling on the power cord.
Do not continue to use your appliance or charger if it appears
faulty. Do not use the appliance to clean animals or people. Do
not replace the batteries with non-rechargeable batteries.
Hoover service: To ensure the continued safe and efficient
operation of this appliance we recommend that any servicing
or repairs are only carried out by an authorised Hoover service
engineer.
End of product Life disposal:
If the appliance is to be disposed of the batteries must first be
removed. The appliance must be disconnected from the supply
mains when removing the battery. Dispose of the batteries
safely. Run the appliance until it stops because the batteries
are fully discharged. Used batteries should be taken to a
recycling station and not disposed of with household waste.
To remove the batteries, please contact the Hoover Customer
Centre or proceed according to the following instructions.
IMPORTANT: Always fully discharge the batteries before
removal.
Run the cleaner until the batteries are completely empty.
Remove the charger jack plug from the appliance.
Press the battery pack release button and slide to remove.
Note: Should you experience any difficulty in dismantling the
unit or for more detailed information on treatment, recovery and
recycling of this appliance, please contact your local city office
or your household waste disposal service.
2
GB
The Environment:
This appliance is marked according to the European directive 2011/65/EC on Waste Electrical and Electronic
Equipment (WEEE). By ensuring this product is disposed of correctly, you will help prevent potential negative
consequences for the environment and human health, which could otherwise be caused by inappropriate
waste handling of this product. The symbol on the product indicates that this product may not be treated
as household waste. Instead it shall be handed over to the applicable collection point for the recycling of
electrical and electronic equipment. Disposal must be carried out in accordance with local environmental
regulations for waste disposal. For more detailed information about treatment, recovery and recycling of this product,
please contact your local city office, your household waste disposal service or the shop where you purchased the product.
Frequency bands
2400Mhz ~ 2483.5Mhz
802.11 b: +20 dBm
802.11 g: +17 dBm
802.11 n: +14 dBm
Maximum RF power transmitted in the frequency band
With this the Candy Hoover Group Srl, declares that this appliance marked with
complies with the essential requirements of the Directives 2014/53/EU and 2011/65/EU. To receive a copy of
the declaration of conformity, please contact the manufacturer at: www.candy-group.com
CANDY HOOVER GROUP S.r.l. Via Privata Eden Fumagalli, 20861 Brugherio (MB) Italy
PRODUCT COMPONENTS
A.
Turbo On/Off Button
R.
ON/OFF Switch
B.
WIFI Switch
S.
Exhaust Filter Release Button
C.
Carpet Button
T.
Exhaust Filter
D.
LED Indicators
U.
Charger
E.
Handheld Release Button
V.
2 In 1 Tool With Quick&Secure Connection*
F.
Tube
W. 2 In 1 Large Dusting And Furniture Brush With Quick &
G.
Nozzle Release Button
H.
Nozzle Front Light
I.
Intense Floor Roller
J.
Dust Cup
Y.
Mini Turbo Nozzle With Quick & Secure Connection*
K.
HSpin-Core+ Technology Assembly:
Z.
Up To Top Tool Adaptor With Quick & Secure Connection*
K1.Motor Cover
AA. Radiator Tool With Quick & Secure Connection*
K2. Mesh Filter
AB. Deep Cleaning Brush With Quick & Secure Connection*
K3. Cover Cup
AC. Accessory Bag*
Motor Shaft
AD. Rear Soft Strip*
L.
Secure Connection*
X.
Long Flexible Crevice Tool With Quick & Secure
Connection*
M. Dust Cup Empty Button
AE. Wiper Blades
N.
Dust Cup Bottom Cover
AF. Wall Mount*
O.
Battery Pack Release Button
AG. Screws Plugs*
P.
Battery Pack
Q.
Switch Lever
PREPARING YOUR CLEANER
1.
2.
3.
4.
Insert the nozzle head into one side of tube until you hear a “click” sound. [1A]
Insert the other side of tube into the handheld unit until you hear a “click” sound. [1B]
Fix the Wall Mount to your wall using the screws and screw plugs provided. [2]
To fully charge the appliance, connect the charger jack plug to the battery pack. It will take around 6Hrs. [2]
NOTE: To remove the nozzle, press the nozzle release button and pull away from the main body.
NOTE: Use only the charger supplied with your cleaner to recharge.
NOTE: Before first use, charge your appliance for at least 24 hours.
IMPORTANT: When charging the cleaner, the switch lever must be in the OFF position. You can charge the battery
pack also when released from the product.
It is normal for the charger to become warm to touch when charging.
* Certain Models Only
3
GB
USING YOUR CLEANER
There are four working modes:
• TEMPORARY MODE: The product will start working when you press on the ON/OFF Switch and stop when released. [3A]
• CONTINUOUS MODE: To enable continuous mode you can pull switch lever back and it will click into place. [3B] To
disable continuous mode you can push the switch lever forward.
• CARPET MODE:Press the Carpet button to use the product on carpets. [4A]
• TURBO MODE: Press the Turbo Button to fully power the product for hard cleaning tasks.[4C]
IMPORTANT: After each use of your product, please ensure to push the switch lever forward to the unlocked position.
Failure to do so may result in a reduction in battery life or failure.
WIFI SETUP
NOTE: This product features wifi connection to enhance the interaction with your cleaner. It allows to get statistics on
the usage of the product as well as additional info on how to use the product at its best. It allows to get notifications and
to monitor the overall maintenance in order to guarantee its performance.
Enrollment
You can switch the WiFi On/Off by pressing the WiFi button as shown in the diagram[4B]. The LED light will
continuously flash until the vacuum cleaner is connected to the Hoover Wizard App.
1. You can download the Hoover Wizard Application by scanning the QR code located on the cover of this manual.
2. Install it on your smart phone.
3. Follow the instructions in the App to setup your vacuum cleaner.
When installed correctly, your smart phone will connect automatically.
RESET WIFI
You can reset your vacuum cleaner by pressing the WiFi button for 5s until the LED light starts flashing.
You need to reconnect the vacuum cleaner to the APP again.
NOTE: once you lock the product by App, you can unlock it both by App or pressing “Turbo” and “Silent” button on the
product for 3 seconds at the same time.
WIPER BLADE ASSEMBLY
To obtain the best crevice and carpet performance, it is recommended to assemble the front and rear wiper blades to
the soleplate of the nozzle.
To do this, open the agitator release flap and remove the soft strip. Then grip one wiper blade, by inserting one end into
the rear slot and slide it in until fully home. Repeat these operations for the second wiper blade and slide it in the front
slot. Lock the agitator release flap. [18]
SAFETY PROTECTION SYSTEM
To ensure the reliability of the product is not affected if used under arduous conditions, the product features an
integrated safety protection system.
NOTE: The Safety protection system will action if the agitator has a blockage or is locked, once actioned, the agitator
will stop rotating and the white Led lights on the front of the nozzle will flash around 10 seconds. If this happens, simply
turn off your product and clear the agitator obstruction. To resume cleaning, press the on/off button and the product will
start in normal mode.
NOTE: The safety protection system will action if the dust bin flap open or dust bin is not in place, once actioned, the
HSpin-Core+ Technology will stop rotating to avoid any damage to the user. If this happens, simply turn off your product
and locate the dust bin and dust bin flap in position.
To resume cleaning, press the on/off button and the product will start in normal mode.
BATTERY
DISPLAY Led:
This cleaner is equipped with a Led display. When the product is ON and the display illuminated the indicators show the
following information.
BATTERY LEVEL INDICATOR:
• 4 points = 100% charge
* Certain Models Only
4
•
•
•
3 points
2 points
1 point
=
=
=
GB
75% charge
50% charge
25% charge
CHARGING
During the charging process if the battery charged level is below 25% you will see the first Led blink until it reaches
above 25%, then it will stay illuminated. This process will continue on all points of the Led indicating level of battery
charge 25%, 50%, 75%, etc. When the battery charge has reached 100% all 4 points will be illuminated.
Please note to ensure your battery is being charged at a safe working temperature we have fitted a safety device. If this
device activates and you commence the charging process then you will see the first Led flash until it has reset. After it
has automatically reset the normal charging process as described above will commence.
DISCHARGING
When the product is running and the batteries are discharging the Led indicator light will start to flash when the battery
capacity is lower than 5% indicating the need to recharge.
ACCESSORIES
2 IN 1 CREVICE & DUSTING BRUSH WITH QUICK &SECURE CONNECTION*, 2-1 LARGE DUSTING & FURNITURE
BRUSH WITH QUICK &SECURE CONNECTION*, LONG FLEXIBLE CREVICE TOOL WITH QUICK &SECURE
CONNECTION*, MULTI FUNCTION UP TO TOP TOOL ADAPTOR WITH QUICK &SECURE CONNECTION*,
MINI TURBO NOZZLE WITH QUICK &SECURE CONNECTION*, RADIATOR TOOL WITH QUICK &SECURE
CONNECTION* AND DEEP CLEANING BRUSH WITH QUICK &SECURE CONNECTION.
The above accessories can be fitted directly into the handheld unit or one side of the tube. [5]
NOTE: The mini-turbo nozzle is ideal for deep cleaning textile surfaces (i.e. sofas) and pet hair removal. Move it steadily
backwards and forwards. After using, please remove hair / threads collected on the brush with scissors if necessary.
NOTE: The long flexible crevice tool is ideal for cleaning in hard to reach areas, underneath furniture and in your car.
NOTE: The radiator tool is ideal for cleaning inside and around cabinets, radiators, couches, blinds and more.
NOTE: The deep cleaning brush is useful to clean in tight spaces without scratching surfaces, and inside your car.
NOTE: The multi-function up to top tool adaptor is recommended to reach high furniture and ceilings. You can attach to
whatever tool, apart from the mini turbo, to clean high corners, curtains, or above high furniture.
ACCESSORY BAG*
Accessories can be stored in the accessory bag.
WALL MOUNT*
Hang the wall mount to the wall, using the three screws included in the product [2] to hang product, 2in1 crevice &
dusting brush, 2in1 large dusting & crevice and mini turbo nozzle (when included).
CLEANER MAINTENANCE
Emptying the Dust Container
1. Press the handheld release button and remove the tube. [6]
2. Press the dust cup empty button to release the bin flap and empty the contents. [7]
3. Close the dust cup flap up, you will hear a click when fully locked.
NOTE: It is recommended to empty the dust cup after each use or when dust is up to the max fill lines.
Cleaning the Dust Container and Filter
1. Press the handheld release button and remove the tube. [6]
2. Press the dust cup empty button to open the bin flap and empty it. [7]
3. Push down the battery pack release button and remove the battery pack. [8A,8B]
4. Turn the dust bin in a clockwise direction, align the arrow marks and remove from cleaner main body. [9]
5. Clean any excess dust from the mesh filter [K2], hold the mesh firmly with one hand and with the other turn the cover
cup [K3] in a clockwise direction to remove the mesh filter. [10]
6. Once the cup cover is removed, pull the HSpin-Core+ Technology assembly away from the main body. [11A] Hold the
top of the motor cover [K1] and remove the mesh filter by pulling away. [11B]
7. Press the two exhaust filter release buttons and then remove the exhaust filter. [12A, 12B]
8. When cleaning the the filters, wash the mesh filter [K2] and exhaust filter [T] in luke warm water. [13] Please ensure
all parts are completely dry before reassembling. [14]
* Certain Models Only
5
GB
9. When reassembling the HSpin-Core+ Technology, firstly reattach the mesh filter to the motor cover, [15A] then align
this assembly with the motor shaft, paying particular attention to the flat surface on the motor shaft. [15B]
10. Secondly again hold mesh filter and refit cover cup: rotate in an anti-clockwise direction to lock [16]. PLEASE
ENSURE YOU DO NOT OVERTIGHTEN AS THIS MAY DAMAGE THE THREAD.
11. Complete reassembly of the handheld unit and then attach it to the wall Mount.
NOTE: Do not use hot water or detergents when cleaning the exhaust filters. In the unlikely event of the exhaust filters
becoming damaged, fit a genuine Hoover replacement. Do not try use the product without a filter fitted.
IMPORTANT: For optimum performance, always keep your mesh filter clean. We recommend that the filter should be
washed at least once a month.
Changing and Cleaning the Agitator
IMPORTANT: Always switch off the cleaner before changing and cleaning the agitator.
1. Detach the agitator release button flap. It is positioned on the lateral part of the nozzle. [17a]
2. Hold the agitator release flap and remove the agitator. [17b]
3. To clean the Intense Floor Roller, remove excess debris using scissors. [17c]
4. Re-fit the agitator. [17d] The agitator can only fit in one direction.
5. Close the agitator release flap to secure the agitator in position. [17e]
Replacing the Batteries
This cleaner is fitted with a rechargeable Lithium ion battery pack and it is replaceable.
WARNING: Only use approved replacement parts for your cleaner. Using parts not validated by Hoover are dangerous
and will invalidate your guarantee.
WARNING: Do not try to open the battery pack and repair it by yourself.
1. Pull down the battery pack release button and the battery pack will be pushed out short distance automatic. [8A]
2. Drag the battery pack slowly from the slot. [8B]
3. Removed the old battery pack and replace with the new battery pack.
4. Dispose of the batteries safely. Used batteries should be taken to a recycling station and not disposed off with
household waste.
TROUBLESHOOTING
Should you have any problem with you cleaner, follow this simple check list before calling the Hoover Customer Service
Centre:
A. Cleaner does not switch on
Check if the cleaner is charged.
Check if the battery pack is assembled in place.
B. HSpin-Core+ Technology motor stop working
Check if the HSpin-Core+Technology motor is blocked.
Clear it and ensure the continuous mode lever is off. Once this is done simply press the on/off button, the
product will restart after a few seconds.
Check if dust bin or dust bin not assemble well.
C. Loss of suction or no suction
Empty the dust cup and wash the mesh filter and clean the HSpin-Core+ Technology assembly.
Remove nozzle and check for any blockages in the duct.
D. Batteries cannot be charged
This may be a result of very long storage periods (over half year).
Contact Hoover customer service to arrange battery replacement.
If the problem persists contact the Hoover customer service centre.
HOOVER SPARES AND CONSUMABLES
Always replace parts with genuine Hoover spares. These are available from your local Hoover dealer or direct from
Hoover. When order parts always quote your model number.
6
GB
YOUR GUARANTEE
The guarantee conditions for this appliance are as defined by our representative in the country in which it is sold. Details
regarding these conditions can be obtained from the dealer from whom the appliance was purchased. The bill of sale or
receipt must be produced when making any claim under the terms of this guarantee.
IMPORTANT: The battery in this cleaner is guaranteed for 1 year from the date of purchase. After 1 year the customer
is liable for the cost of a new battery.
Subject to change without notice.
7
PRINTED IN P.R.C.
48027621
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising