Hoover | WDWFT 4138AH-80 | Hoover WDWFT 4138AH-80 User manual

Hoover WDWFT 4138AH-80 User manual
EN
Thank-you for choosing a Hoover washing
machine. We are proud to always offer new,
innovative and technologically advanced
products, with a complete range of home
appliances to ensure true assistance in your
daily routine.
Environmental conditions
This appliance is marked according to
the European directive 2012/19/EU
on Waste Electrical and Electronic
Equipment (WEEE).
WEEE contains both polluting substances (which
can cause negative consequences for the
environment) and basic components (which can
be re-used). It is important to have WEEE
subjected to specific treatments, in order to
remove and dispose properly all pollutants, and
recover and recycle all materials. Individuals can
play an important role in ensuring that WEEE
does not become an environmental issue; it is
essential to follow some basic rules:
Carefully read this manual for correct and
safe appliance use and for helpful tips on
efficient maintenance.
Only use the washing machine after
carefully reading these instructions. We
recommend you always keep this manual on
hand and in good condition for any future
owners.
l WEEE should not be treated as household
waste;
l WEEE should be handed over to the relevant
Please check that the appliance is delivered
with this instruction manual, warranty
certificate, service centre address and
energy efficiency label. Also check that
plugs, drain hose support hook and liquid
detergent or bleach tray (only on some
models) are included. We recommend you
keep all these components.
collection points managed by the municipality or
by registered companies. In many countries, for
large WEEE, home collection could be present.
In many countries, when you buy a new
appliance, the old one may be returned to the
retailer who has to collect it free of charge on a
one-to-one basis, as long as the equipment is of
equivalent type and has the same functions as
the supplied equipment.
FOR U.K. ONLY
On receipt of your appliance please
check it carefully for damage. Any
damage found must be reported
to the delivery driver immediately.
Alternatively damage found must be
reported to the retailer within 2 days of
receipt.
Contents
1. GENERAL SAFETY RULES
2. INSTALLATION
3. PRATICAL HINTS
4. CLEANING AND MAINTENANCE
5. QUICK USER GUIDE
Each product is identified by a unique 16character code, also called the “serial
number”, printed on the sticker. This can be
found inside the door opening. This code is
a unique code for your product that you will
need to register the product warranty, or if
you need to contact the Customer Service
Centre.
6. CONTROLS AND PROGRAMS
7. DRYING CYCLE
8. AUTOMATIC WASHING/DRYING CYCLE
9. THROUBLESHOOTING AND WARRANTY
2
l This
appliances is intended to
be used in household and
similar applications such as:
- Staff kitchen areas in shops, offices
and other working environments;
- Farm houses;
- By clients in hotels, motels and
other residential type environments;
- Bed and breakfast type environments.
A different use of this appliance
from household environment
or from typical housekeeping
functions, as commercial use by
expert or trained users, is excluded
even in the above applications. If
the appliance is used in a manner
inconsistent with this it may reduce
the life of the appliance and may
void the manufacturer’s warranty.
Any damage to the appliance or
other damage or loss arising
through use that is not consistent
with domestic or household use
(even if located in a domestic or
household environment) shall not
be accepted by the manufacturer to
the fullest extent permitted by law.
l Children
should be supervised
to ensure that they do not play
with the appliance.
l Children
of less than 3 years
should be kept away unless
continuously supervised.
l If
the supply cord is damaged, it
must be replaced by a special
cord or assembly available from
the manufacturer or its service
agent.
l Only
use
the
hose-sets
supplied with the appliance for
the water supply connection
(do not reuse old hose-sets).
l Water
pressure must be between
0.05 MPa and 0.8 MPa.
l Make
sure carpets or rugs do
not obstruct the base or any of
the ventilation openings.
l This
appliance can be used by
children aged from 8 years and
above and persons with reduced l The final part of a washer dryer
cycle occurs without heat (cool
physical, sensory or mental
down cycle) to ensure that the
capabilities or lack of experience
items are left at a temperature
and knowledge if they have been
that ensures that the items will
given supervision or instruction
not be damaged.
concerning use of the appliance
3
EN
in a safe way and understand the
hazards involved.
Children shall not play with the
appliance. Cleaning and user
maintenance shall not be made
by children without supervision.
1. GENERAL SAFETY
RULES
l Items
such as foam rubber
(latex foam), shower caps,
waterproof textiles, rubber
backed articles and clothes or
pillows fitted with foam rubber
pads should not be dried in the
washer dryer.
WARNING:
never stop a washer dryer before
the end of the drying cycle
unless all items are quickly
removed and spread out so that
the heat is dissipated.
installation, the appliance l Fabric softeners, or similar
products, should be used as
must be positioned so that the
specified by the fabric softener
plug is accessible.
instructions.
l The appliance must not be
installed behind a lockable l Oil-affected items can ignite
spontaneously, especially when
door, a sliding door or a door
exposed to heat sources such
with a hinge on the opposite
as a washer dryer. The items
side to that of the washer
become warm, causing an
dryer, in such way that a full
oxidation reaction in the oil,
opening of the washer dryer
Oxidation creates heat. If the
door is restricted.
heat cannot escape, items can
l The maximum load capacity of
become hot enough to catch
dry clothes depends on the
fire. Piling, stacking or storing
model used (see control panel).
oil-effected items can prevent
heat from escaping and so
l The appliance is not to be used
create a fire hazard.
if industrial chemicals have
been used for cleaning.
l If it is unavoidable that fabrics
contain vegetable or cooking
l Do not dry unwashed items in
oil or have been contaminated
the washer dryer.
by hair care products be
l Items that have been soiled with
placed in a washer dryer they
substances such as cooking oil,
should first be washed in hot
acetone, alcohol, petrol, kerosene,
water with extra detergent spot removers, turpentine, waxes
this will reduce, but not
and wax removers should be
eliminate, the hazard.
washed in hot water with an extra
amount of detergent before being l Remove all objects from pockets
dried in the washer dryer.
such as lighters and matches.
l After
4
consult the product technical l Do not pull on the power cord
specification please refer to the
or appliance to unplug the
manufacturer website.
machine.
Electrical connections
safety instructions
l Make
sure there is no water in
the drum before opening the
door.
and
l The
technical details (supply
voltage and power input) are
indicated on the product rating
plate
WARNING:
water may reach very high
temperatures during the
wash cycle.
l Make
sure that the electrical
system is earthed, complies
with all applicable law and that
l Do not expose the washing
the (electricity) socket is
machine to rain, direct sunlight
compatible with the plug of the
or other weather elements.
appliance. Otherwise, seek
Protect from possible freezing.
qualified professional assistance.
use of converters, multiple l When moving, do not lift the
washing machine by the knobs
sockets or extension cords is
or detergent drawer; during
strongly advised against
transport, never rest the door on
the trolley. We recommend two
people lift the washing machine.
l The
WARNING:
the appliance must not be
supplied through an external
switching device, such as a
timer, or connected to a circuit
that is regularly switched on
and off by a utility.
l In
the event of fault and/or
malfunction, turn off the
washing machine, close the
water tap and do not tamper
with the appliance.
Immediately
contact
the
Customer Service Centre and
only use original spare parts.
Failure to observe these
instruction may jeopardise
appliance safety.
l Before
cleaning or maintaining
the washing machine, unplug
the appliance and turn off the
water tap.
5
EN
l To
2. INSTALLATION
l Remove
the 2 or 4 transportation
screws (A) on the back and
remove the 2 or 4 flat washers,
rubber bungs and plastic spacer
tubes (B) as illustrated in figure 1.
l If the washing machine is built-in,
unscrew the 3 or 4 transportation
screws (A) and remove the 3 or 4
flat washers, rubber bungs and
plastic spacer tubes (B).
l During the removal of the screws
occasionally spacer tubes fall
inside the product, these can be
remove by tilting the product forward
and recovering them from the floor or
inside the base of the machine.
l Cover the open transportation screw
holes with the 2 or 4 plastic caps
included in the instruction bag.
1
A
B
A
B
B
B
A
A
2
A
1
WARNING:
2
3
keep packaging materials
away from children.
l Place
the corrugated plastic sheet,
found on top of the appliance during
the unpacking process, into the base
of the appliance as shown in figure 2
(according to the model, consider
version A, B or C).
In some models this operation
will not be necessary, because
the corrugated plastic sheet
will be already placed on the
bottom of the appliance.
C
3
2
6
B
1
Hydraulic connections
3
EN
l Connect the water hose to the water
supply tap (fig. 3) only using the hose
supplied with the appliance (do
not
reuse old hose-sets).
l SOME MODELS may include one or
more of the following features:
l HOT&COLD (fig. 4):
water mains connection settings with hot
and cold water for higher energy savings.
Connect the grey tube to the cold water
tap
and the red one to the hot water
tap. The machine can be connected to
the cold water tap only: in this case, some
programs may start a few minutes later.
4
1
l AQUASTOP (fig. 5):
a device located on the supply tube that
stops water flow if the tube deteriorates;
in this case, a red mark will appear in the
window “A” and the tube must be
replaced. To unscrew the nut, press the
one-way lock device "B".
5
6
B
l AQUAPROTECT – SUPPLY TUBE WITH
GUARD (fig. 6):
Should water leak from the primary
internal tube "A", the transparent
containment sheath "B" will contain water
to permit the washing cycle to complete.
At the end of the cycle, contact the
Customer Service Centre to replace the
supply tube.
A
B
A
7
Setting
l The washing machine should be installed
in its final position such that the water fill
hose is not kinked or trapped. The
corrugated drain hose should be inserted
into suitable drain pipe of between 50 cm
and 85 cm height above the floor using
the curved drain hose support. If an under
sink connection is used the drain hose
must be routed above the sink overfill
opening to prevent back siphoning. Care
must be taken to avoid kinking or trapping
the drain hose (fig. 7).
max 100 cm
min 4 cm
7
+2,6 mt
max
min 50 cm
max 85 cm
l Level the appliance using the feet as
8
illustrated in figure 8:
a. turn the nut clockwise to release the
screw;
b. rotate the foot to raise or lower it until it
touches to the floor;
c. lock the foot, screwing in the nut, until it
tightens against to the bottom of the
washing machine.
l Plug in the appliance.
A
B
WARNING:
C
contact the Customer Service Centre
should
the
power
cord
need
replacement.
WARNING:
Detergent drawer
installation faults are not covered by
the manufacturers warranty.
The detergent draw is split into 3
compartments as illustrated in figure 9:
l compartment "1": for prewash detergent;
l compartment “ ”: for special additives,
softeners, starch fragrances, etc.;
9
WARNING:
1
only use liquid products; the washing
machine is set to automatically dose
additives at each cycle during the last
rinse.
2
l compartment "2": for washing detergent.
A liquid detergent cup is also included IN
SOME MODELS (fig. 10). To use it, place it
in compartment "2". This way, liquid
detergent will only enter the drum at the
right time. The cup can also be used for
bleach when the “Rinse” program is
selected.
10
WARNING:
some detergents are not designed for
use in the dispenser drawer but are
supplied with their own dispenser that
is placed in the drum directly.
8
Load tips
Before using a drying
(WASHER-DRYERS)
When sorting laundry, make sure:
- have eliminated metallic objects such as
hair clips, pins, coins, from laundry;
programme
l SAVE energy and time by selecting a
high spin speed to reduce the water
content in laundry before using a drying
programme.
- to have buttoned pillow cases, closed
zips, tied loose belts and long robe
ribbons;
Following is a quick guide with tips and
recommendations on detergent use at the
various temperatures. In any case, always
read the instructions on the detergent for
correct use and doses.
- to have removed rollers, hooks or clips
from curtains;
- to have carefully read clothing washing
labels;
- to have removed any persistent stains
using specific detergents.
When washing heavily soiled whites,
we
recommend
using
cotton
programs of 60°C or above and a
normal washing powder (heavy duty)
that contains bleaching agents that at
medium/high
temperatures
provide
excellent results.
l When washing rugs, bedcovers or other
heavy clothing, we recommend you avoid
the spinning cycle.
l To wash wool, make sure the item can be
machine washed. Check the fabric label.
For washes between 40°C and 60°C
the type of detergent used needs to be
appropriate for the type of fabric and
level of soiling.
Normal powders are suitable for “white”
or colour fast fabrics with high soiling,
while liquid detergents or “colour
protecting” powders are suitable for
coloured fabrics with light levels of
soiling.
Helpful suggestions for the user
A guide environmentally friendly and
economic use of your appliance.
Maximise The Load Size
l Achieve the best use of energy, water,
detergent and time by using the
recommended maximum load size.
Save up to 50% energy by washing a full
load instead of 2 half loads.
For washing at temperatures below
40°C we recommend the use of liquid
detergents or detergents specifically
labeled as suitable for low temperature
washing.
Do you need to pre-wash?
l For heavily soiled laundry only!
SAVE detergent, time, water and
between 5 to 15% energy consumption
by NOT selecting Prewash for slight to
normally soiled laundry.
For washing wool or silk, only use
detergents specifically formulated for
these fabrics.
Is a hot wash required?
l Pretreat stains with stain remover or soak
dried in stains in water before washing to
9
EN
reduce the necessity of a hot wash
programme. Save energy by using a low
temperature wash programme.
3. PRATICAL HINTS
l Remove and clean the filter; when
4. CLEANING AND
MAINTENANCE
To clean the washing machine exterior, use
a damp cloth, avoiding abrasives, alcohol
and/or solvents. To maintain a good wash
performance we recommend that the soap
drawer and pump filters are regularly
cleaned. A monthly service wash, using a
proprietary cleaner is also recommended.
finished, replace it turning it clockwise.
The filter handle will be locked when it is
not possible to turn any further and the
handle is horizontal. Smearing a small
amount of liquid soap on the filter seal will
help refitting.
l Repeat the previous steps in reverse
order to reassemble all parts.
Drawer cleaning
l We recommend you clean the drawer to
avoid accumulating
additive residue.
detergent
and
l To do this, extract the drawer using slight
force, clean it with running water and
reinsert it in its housing.
l Ensure the siphon cap is correctly
refitted.
Filter cleaning
l Should the washing machine be stored in
l The washing machine comes with a
special filter able to trap large residue,
such as buttons or coins, which could
clog the drain.
l ONLY AVAILABLE ON CERTAIN MODELS:
pull out the corrugated hose, remove the
stopper and drain the water into a
container.
l Ensure all the water has been emptied
from the drum.
l Before
unscrewing the filter, we
recommend you place an absorbent cloth
under it to keep the floor dry. A small
amount of water will come out of the filter
as you remove it - this is normal.
l Turn the filter counter-clockwise to the
limit stop.
10
S u g g e s tio n s fo r m o v e s o r
prolonged disuse
an unheated room for a long period of
time, drain all water from tubes.
l Unplug the washing machine.
l Detach the tube from the drainage
system and clip on the rear of the
machine and lower it, fully draining water
into a bowl.
l Secure the drain tube with the drainage
system and clip on the rear of the
machine when finished.
l Keep the door glass and gasket clean.
The manufacturers warranty only
covers faults within the product of a
mechanical or electrical nature.
Faults
caused
by
handling,
installation or miss use are not
covered and may incur a charge for
any repair visit to resolve.
This washing machine automatically adjusts
the level of the water to the type and
quantity of washing. This system gives a
reduction in energy consumption and a
saving in washing times.
6. CONTROLS AND
PROGRAMS
EN
5. QUICK USER GUIDE
Q
}
Program selection
A
l Turn on the washing machine and select
the required program.
l Adjust
the washing temperature if
necessary and press the required "option"
buttons.
DRYING
If you would like the drying cycle to
begin automatically after washing,
select the programme required using
the DRYING SELECTION button.
Or you can finish the wash and then
select the drying programme and
load size.
l Press the START/PAUSE button to start
washing.
P
Wait until the DOOR LOCKED light has
gone out before opening the door.
l Turn off the washing machine.
For any type of wash, see the program
table and follow the operating sequence
as indicated.
Technical data
Water pressure:
min 0.05 Mpa / max 0.8 Mpa
(0.05 MPa dispenses approximately 1 litre
of water in 10 seconds)
Spin r.p.m.: See rating plate.
Power input / Power current fuse amp /
Supply voltage: See rating plate.
R
B
G
A
B
C
D
E
F
G
H
I
L
M
N
O
P
Q
H
I
L M
NE
Touch Control (with OFF button)
START/PAUSE button
SPIN SPEED button
TEMPERATURE SELECTION
button
DELAY START button
RAPID / STAIN LEVEL button
PREWASH button
HYGIENE PLUS button
EXTRA RINSE button
DRYING SELECTION button
FAVOURITES button
ACTIVE STEAM button
Digital display
DOOR LOCKED indicator light
DRYING PROGRAMME
SELECTION button
E+N KEY LOCK
R ONE Fi EXTRA area
11
F
D
C
l At the end of the programme, the
message "End" will appear on the display
or, on some models, all wash stage
indicator lights will turn on.
O
BUTTON SELECTION indicators
WARNING:
They light up at the touch of the related
button
.
Don’t touch the display (and the Touch
Control) while inserting the plug because
the machines calibrates the systems
during the first seconds: touching the
display, the machine couldn’t work
property. In this case, remove the plug
and repeat the operation.
"X Red Light"
It lights up at the pressing of any button of
the Touch Control, with a diffused lighting
fading to the edges
.
It gradually turns off within 5 minutes since
the last touch of a button, in order to save
energy.
Touch Control
START/PAUSE button
Close the door BEFORE selecting the
button START/PAUSE.
l Press to start the selected cycle.
When the START/PAUSE button has
been pressed, the appliance can take
few seconds before it starts working.
ON/OFF
Press for at least 1 second the button of a
selected program
to turn on the
appliance (the display will light up, showing
the parameters of the selected cycle). To
switch off the appliance, press the OFF
for at least 3 seconds.
PROGRAMME SELECTION
To set a program press the related button
, the corresponding indicator will light up.
ADD OR REMOVE ITEMS AFTER THE
PROGRAMMES HAS STARTED (PAUSE)
l Press and hold the START/PAUSE
button for about 2 seconds (some
indicator light and the time remaining
indicator will flash, showing that the
machine has been paused).
l Wait until the DOOR LOCKED light has
gone out before opening the door.
Before you open the door, please
check water level is below the door
opening to avoid flooding.
l After you have added or removed items,
close the door and press the
START/PAUSE button (the programme
will start from where it left off).
CANCELLING THE PROGRAMME
l To cancel the programme, press the OFF
button (for at least 3 seconds).
12
l Wait 2 minutes until the safety device
The option buttons should be selected
before pressing the START/PAUSE
button.
If an option is selected that is
not compatible with the selected
programme then the option indicator
first flashes and then goes off.
l This button allows you to change the
temperature of the wash cycles.
cold wash.
l It is not possible to raise the temperature
over the maximum allowed for every
programme, in order to save the fabrics.
SPIN SELECTION button
DELAY START button
l By pressing this button, it is possible to
reduce the maximum speed, and if you
wish, the spin cycle can be cancelled.
l This button allows you to pre-programme
the wash cycle to delay the start of the
cycle for up to 24 hours.
spin speed cancelled.
l If the label does not indicate specific
information, it is possible to use the
maximum spin expected in the program.
l To delay the start use the following
procedure:
- Set the required programme.
To prevent damage to the fabrics, it is
not possible to increase the speed
over the maximum allowed for the
programme.
- Press the button once to activate it (h00
appears on the display) and then press
it again to set a 1 hour delay (h01
appears on the display). The pre-set
delay increases by 1 hour each time the
button is pressed, until h24 appears on
the display, at which point pressing the
button again will reset the delay start to
zero.
l To reactivate the spin cycle press the
button until you reach the spin speed you
would like to set.
l It is possible to modify the spin speed
without pausing the machine.
An over dosing of detergent can cause
excessive foaming. If the appliance
detects the presence of excessive foam,
it may exclude the spinning phase or
extend the duration of the program
and increase water consumption.
The machine is fitted with a special
electronic device, which prevents the
spin cycle should the load be
unbalanced. This reduces the noise
and vibration in the machine and so
prolongs the life of your machine.
- Confirm by pressing the START/PAUSE
button (the light on the display starts to
flash). The countdown will begin and
when it has finished the programme will
start automatically.
l It is possible to cancel the delay start
by pressing the OFF button (for at least
3 seconds).
If there is any break in the power supply
while the machine is operating, a special
memory stores the selected programme
and, when the power is restored, it
continues where it left OFF
13
EN
TEMPERATURE SELECTION button
unlocks the door.
l This function has been studied for the
RAPID / STAIN LEVEL button
This button allows you to choose between
two different options, depending on the
selected programme.
- RAPID
The button becomes active when
you select the RAPID (14/30/44 Min.)
programme on the knob and allows you to
select one of three durations indicated.
- STAIN LEVEL button
l Once the programme has been selected
the wash time set for that programme will
be automatically shown.
l This option allows you to choose between
3 levels of wash intensity modifying the
length of the programme, depending on
how much the fabrics are soiled (can only
be used on some programmes as shown
in the table of programmes).
PREWASH button
people with delicate and sensitive skin,
for which also a least residue of detergent
can cause irritations or allergies.
l It advises to also use this function for the
children items and in case of washings of
very dirty items, for which it is due to use
a lot of detergent, or in the washing of
toweling items whose fibres mostly have
the tendency to hold the detergent.
DRYING SELECTION button
l For automatic washing/drying cycle:
after the selection of washing programme
according to laundry type, select a degree
of dryness by pressing this button. At the
end of the washing programme, the
selected
drying
cycle
will
start
automatically.
If a washing programme is not
compatible
with
automatic
drying
selected, this function will not be
activated.
l This option allows you to make a prewash
and it is particularly useful for heavily
soiled loads (can be used only on
some programmes as shown in the
table of programmes).
If you exceed the maximum dryable
load of laundry indicated in the
programme table, the laundry may not
be dried satisfactory.
l We recommend you use only 20% of the
recommended quantities shown on the
detergent pack.
HYGIENE PLUS button
With this option it is possible to hygienize
the clothes, the washing programme
reach a temperature of 60°C.
EXTRA RINSE button
l This button allows you to add rinses at
the end of the washing cycle. The
maximum number of extra rinses is
related to the programme selected.
14
l If you want delete the selection before
the programme starts, please press
repeatedly the button until the lights go off
or press the OFF button (for at least
3 seconds).
l Drying only cycle:
select via the knob the desired drying
programme in conjunction with your
fabrics, by pressing this button it is
possible to select a degree of dryness
that is different to the default one (except
for the wool drying programme).
l To cancel the cycle during the drying
phase, please press the button for about
3 seconds.
After cancelling the drying programme,
the cool down phase will begin and
please wait for about 10/20 minutes
before opening the door.
l "End" will appear in the display at the
end of the program and the DOOR
LOCKED light will go off, it is now
possible to open the door.
It is also possible to cancel the drying
cycle by pressing for at least 3 seconds
the OFF button. It is necessary to wait
for the cooling phase’s end (10/20
minutes) and the DOOR LOCKED light
to go off before opening the door.
Start a program
memorized:
How to memorize a programme for the
first time:
1)
Select the programme
options you want.
and
the
2)
Press the FAVOURITES button,
choosing either M1 or M2. You should
choose M1 if this is the first
programme you have saved.
3)
Keep
your
finger
on
the
FAVOURITES button for about 3
seconds to save the combination in
the chosen position.
Memorize a new programme when M1 &
M2 already have programmes saved:
1)
Set the programme and the options
you want.
is
already
(once for M1, twice for M2) and press the
START/PAUSE button.
l Once you recall a memorized program,
you can still change its options and
settings, pressing the corresponding
keys. In this case, the added options
won’t be memorized.
If you accidently select a memorized
program, simply turn the program
knob to select another one.
ACTIVE STEAM button
After the selection of "ACTIVE STEAM"
programme, select between three different
intensity of steam treatments that are
suitable for dry or wet clothes and
according to fabric type:
- Active Steam Synthetics/Mixed
(default selection) P1 appears on the
display
This programme is suitable for synthetics
and mixed clothes. In the case of wet
clothes (i.e. after washing) If relax creases
is selected after spin the dry clothes will
reach the ideal moisture level for an easy
ironing. Medium time.
- Active Steam Cotton
(only a button push) P2 appears on the
display
This programme is for cotton clothes. In
the case of wet clothes (i.e. after washing)
If relax creases is selected after spin the
dry clothes will reach the ideal moisture
level for an easy ironing. Medium time.
15
that
l Press briefly the FAVOURITES button
FAVOURITES button
This function allows you to save the settings
of your two favourite personalised
programmes, including the temperature,
spin speed and soil level, so you can recall
them quickly.
Press the FAVOURITES button for
about 3 seconds to save the
combination in the position M1. The
pre-existing saved programme in M1
will move in the position M2.
EN
2)
WARNING:
- Steam Refresh
(two button pushes) P3 appears on the
display
Thanks to the steam action, the cycle lets
to refresh and relax clothes’ creases after
use. This programme consists of a start
phase in which the steam in introduced
and the excess moisture is removed at
the final stage to allow prompt use. This
cycle is suitable for dry clothes.
The function is suitable for max up to 1,5 kg
load.
Moreover, this button allows a specific
treatment to follow certain wash cycles
(please refer to the program table). The
steam function works by relaxing creases in
wet garments and as a result reduces the
time needed to iron these items. The fibres
are regenerated and refreshed by removing
bad smells. Every program provides a
dedicated steam treatment in order to
ensure the maximum cleaning efficiency
according to the items fabric type and
colour.
Digital Display
The display’s indicator system allows you to
be constantly informed about the status of
the machine.
1 15
6 10
16 12
5
3
2
7
7
13 14
7
8
7
7
9 11 4
1) DOOR LOCKED INDICATOR LIGHT
l The indicator light is illuminated when the
door is fully closed.
Close the door BEFORE selecting the
START/PAUSE button.
l When START/PAUSE is pressed on
the machine with the door closed, the
indicator will flash momentarily and then
illuminate.
DRYING PROGRAMME
SELECTION button
This button allows you to select one of three
drying programmes available. By pressing
this button, one indicator light will go on to
show the selected drying programme.
KEY LOCK
If the door is not properly closed,
the light will continue to flash for
about 7 seconds, after which the
start command will be automatically
delete. In this case, close the door
in the proper way and press the
START/PAUSE button.
l Pressing
simultaneously the buttons
ACTIVE STEAM and DELAY START for
about 3 seconds, the machine allows
you to lock the keys. In this way, you can
avoid making accidental or unwanted
changes if a button on the display is
pressed accidently during a cycle.
l The key lock can be simply cancelled by
pressing the two buttons simultaneously
again or by pressing the OFF button (for
at least 3 seconds).
16
l Wait until the DOOR LOCKED light has
gone out before opening the door.
2) SPIN SPEED
This show the spin speed of the selected
programme that can be changed or omitted
by the relevant button.
spin speed cancelled.
l For
all the information about the
functionality and the instructions for an
easy configuration of the Wi-Fi, please
refer to the "Download" section on
http://wizardservice.candy-hoover.com.
This show the washing temperature of the
selected programme that can be changed
(where allowed) by the relevant button.
cold wash.
4) CYCLE DURATION
l When a programme is selected the
display automatically shows the cycle
duration, which can vary, depending on
the options selected.
l Once the programme has started you will
9) DELAY START INDICATOR LIGHT
This flashes when delay start has been set.
10) Kg MODE (function active only on
certain programmes)
l For the programmes where the "Kg
MODE" function is active, the appliance
in the first minutes it calculates the real
laundry loaded, updating the levels on the
display in real time.
Every levels shown on the display is the
20% of the maximum loading capacity.
When a programme is selected the
maximum capacity suggested is shown
on the display.
be kept informed constantly of the time
remaining to the end of the wash.
l The appliance calculates the time to the
end of the selected programme based
upon a standard loading, during the cycle,
the appliance corrects the time to that
applicable to the size and composition of
the load.
l If automatic washing/drying is selected, at
l Through every wash phase "Kg MODE"
allows to monitor information on the wash
load in the drum and in the first minutes
of the wash it:
the end of the wash phase, the drying time
remaining to the end will be shown on the
display.
- adjusts the amount of water required;
5) STAIN LEVEL INDICATOR LIGHTS
l Once the programme has been selected,
- determines the length of the wash cycle;
the indicator light will automatically show
the stain level set for that programme.
- controls rinsing according to the type of
fabric selected to be washed it;
l Selecting a different stain level the
relevant indicator will light up.
- adjusts the rhythm of drum rotation for
the type of fabric being washed;
6) EXTRA RINSES INDICATOR LIGHTS
The indicator lights show the extra rinses
selected by the relevant button.
- recognizes the presence of lather,
increasing, if necessary, the amount of
water during rinsing;
7) OPTIONS INDICATOR LIGHTS
The indicator lights show the options that
can be selected by the relevant buttons.
8) Wi-Fi (some models only)
l In the models with the Wi-Fi option, the
icon indicates that the Wi-Fi system is
working.
- adjusts the spin speed according to the
load, thus avoiding any imbalance.
11) FAVOURITES
The indicator light show that the memory
function is working.
17
EN
3) WASH TEMPERATURE
12) KEY LOCK INDICATOR LIGHT
16) DRYING SELECTION INDICATOR LIGHTS
The indicator light show that the keys are
locked.
The indicators display the degrees of dryness
that can be selected by the relevant button:
13) TAP CLOSED INDICATOR LIGHT
Indicates that the machine is unable to load
the water: it is suggested to turn off the
machine, check that the tap is open and the
water pressure is not particularly low.
14) FILTER BLOCKED INDICATOR LIGHT
Indicates that the machine is not able to
drain the water: it is suggested to turn off the
machine, check that the filter is not clogged or
that the drain hose is not kinked or crushed.
15) STANDARD COTTON PROGRAMMES
LIGHTS (see table of programmes)
The lights will light up when you select the
most efficient program in terms of water and
energy consumption, to wash cotton
garments with a normal grade of soil.
18
Automatic drying programmes
EXTRA DRY
(suitable for towels, bathrobes and
bulky loads).
IRON DRY
(that leaves the laundry ready for
ironing).
CUPBOARD DRY
(for items that will be put away
without ironing).
Timed drying programmes
They may be used to select timed
drying programmes.
Cool down phase
Activated during the final cool down
period, in the last 10/20 minutes of
each drying phase.
NOTES:
Place your smartphone so that the
NFC antenna on its back matches
the position of the ONE Fi EXTRA logo
on the appliance (as illustred below).
This appliance is equipped with ONE Fi
EXTRA technology that allows you to control
it remotely via App, thanks to Wi-Fi function.
MACHINE ENROLLMENT (ON APP)
l Download the Hoover Wizard App on
your device.
The Hoover Wizard App is available
for devices running both Android and
iOS, both for tablets and for
smartphones.
If you do not know the position of
your NFC antenna, slightly move the
smartphone in a circular motion over
the ONE Fi EXTRA logo until the App
confirms the connection. In order for
the data transfer to be successful, it is
essential TO KEEP THE SMARTPHONE
ON THE DASHBOARD DURING THE
FEW SECONDS OF THE PROCEDURE;
a message on the device will inform
about the correct outcome of the
operation and advise you when it is
possible to move the smartphone
away.
Get all the details of the ONE Fi EXTRA
functions by browsing the App in
DEMO mode.
l Open the App, create the user profile and
enroll the appliance following the
instructions on the device display or the
"Quick Guide" attached on the machine.
Using
an
Android
smartphone
equipped with NFC technology (Near
Field Communication), the enrollment
process is simplified (Easy Enrollment);
in this case, follow the instructions on
the phone display, PLACE AND KEEP
IT NEAR the ONE Fi EXTRA logo
on the machine dashboard, when
requested to do so by the App.
Thick cases or metallic stickers on
your smartphone could affect or
prevent the transmission of data
between machine and telephone. If
necessary, remove them.
The replacement of some components
of the smartphone (e.g. back cover,
battery, etc...) with non-original ones,
could result in the NFC antenna removal.
ENABLE REMOTE CONTROL (VIA APP)
After the machine enrollment, every time
you want to manage it remotely through the
App, firstly you have to load the laundry, the
detergent, close the door and select the
ONE FI EXTRA position on the machine.
From that moment on you can manage it
through the App commands.
19
EN
ONE Fi EXTRA
Table of programmes
1)
2
(MAX.) *
PROGRAMME
(see control panel)
(MAX.)
Tabella programmi
Active Steam
n
n
Mixed
All In One
All Delicates
All In One 49 Min.
1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5
2)
4)
4)
4)
3
4 4,5 5
5 5,5 6 6,5
40°
10 10 11 12 13
40°
8
9
Rinse
-
-
-
-
-
-
Wool & Silk
1
2
2
2
2
2 2,5 2,5
Wool
1
1
1
1
1
1
1
1
-
5
5
6
6
8
8
8
8
-
3
4 4,5 5
6
8
High Heat
(drying)
Low Heat
(drying)
Cottons**
3) 4)
Rapid
14-30-44 Min.
Drain & Spin
2)
4)
9
-
-
5 5,5 6 6,5
10 10 11 12 13
30°
90°
14' 1 1,5 1,5 1,5 1,5 1,5 2
2
30°
30' 2 2,5 2,5 2,5 2,5 2,5 3
3
30°
44' 3 3,5 3,5 3,5 3,5 3,5 4
4
40°
-
-
-
-
-
-
-
-
-
1
40°
3
2 2,5 2,5 2,5 2,5 2,5 3
2
-
6
(drying)
n
1
( )
Position that you have to select when you want to enable remote control through
the App (via Wi-Fi). If the machine is not enrolled on the app yet, pressing the
START/PAUSE button on the appliance will perform the "Auto-Hygiene" cycle,
made to clean the drum.
n Steam Function Available.
20
2)
TEST
50229
Drying
First drying with A kg (a load consist:
pillowcases and hand-towels) selecting
the
cotton
drying
programme
(
) cupboard dry (
).
Second drying with B kg (a load consist:
sheets and hand towels) selecting
the
cotton
drying
programme
(
Only with PREWASH option selected
(programmes with PREWASH option
available).
When a programme is selected,
on the display is shown the
display shows the recommended
wash temperature that can be
reduced (where allowed) by the
relevant button.
For the programmes shown you
can adjust the duration and
intensity of the wash using the
STAIN LEVEL button.
) cupboard dry (
).
Capacity
(washing)
(kg)
A (kg)
B (kg)
First
drying
Second
drying
6
5
1
8
5
3
9
6
3
10
6
4
10
8
2
11
8
3
12
8
4
13
8
5
EN
Programmes for automatic drying.
Use the programme ** with the maximum
degree of soiling selected, maximum spin
speed and a temperature of 60°C.
Programme recommended also for test
with a lower temperature.
21
4)
Washing
(Only for models with liquid
detergent compartment)
When only a limited number of
articles have stains which require
treatment with liquid bleaching
agents, preliminary removal of
stain can be carried out in the
washing machine.
Pour the bleach into the liquid
bleach container, inserted into the
compartment marked "2" in the
detergent drawer, and set the
special programme RINSE.
When this phase has terminated,
switch off the appliance, add the
rest of the fabrics and proceed
with a normal wash on the most
suitable programme.
1)
Selecting the RAPID program on
the knob, it will be possible to
select with the RAPID button, one
of the three rapid programs
available among 14’, 30’ and 44’.
INFORMATION FOR THE
LABORATORIES (Ref. EN
Standards)
Please read these notes:
* Maximum load capacity of dry clothes,
according to the model used (see control
panel).
( )
3)
Programmes selection
l Certain large dark items such as jeans
To clean different types of fabrics and
various levels of dirt, the washing machine
has specific programs to meet every need
of washing (see table of programmes).
l Never mix NON COLOURFAST fabrics.
WASHING
Active Steam
This exclusive programme uses a steam
treatment that allows you to reduce and relax
the creases reaching the ideal moisture level
easier ironing. Through a dedicated button it’s
possible to select three different levels of
intensity, customizing for dry or wet items, and
accordingly on the type of fabric.
ALL IN ONE technology
This washing machine is equipped with an
innovative system with an high pressure jet
that sprays a mixture of water and
detergent directly into the load. The special
motor movement used in this machine
manages the drum movement during the
start up of each programme, in conjunction
with the high pressure jet spraying the
detergent mixture into the load, the cycle
includes a set of spin actions that helps the
detergent solution to penetrate into the
fibers, helping dirt removal and ensuring
the best available wash performance. The
ALL IN ONE system is also used during the
water load phases where the high pressure
jet aids the complete removal of detergent
residues trapped in the clothes.
Mixed All In One
This programme allows you to wash
different type’s fabrics and different colours
all together. The rotational movement of the
drum and the water levels are optimized
during the washing and rinsing phases. The
accurate spin action, ensures a reduced
formation of creases in the fabrics. Thanks
to ALL IN ONE technology, a complete
washing cycle optimization is possible.
IMPORTANT WASH PERFORMANCE
ADVICE:
l New, coloured garments should be
washed separately for at least 5 or 6
washes.
22
and towels should always be washed
separately.
All Delicates
This program has reduced periods of drum
rotation during the cycle and is particularly
suitable or washing delicate fabrics. The
wash cycle and rinses are carried out with a
high level of water to ensure the best
performance.
All In One 49 Min.
This programme allows you to wash mixed
fabrics such as cottons, synthetics and
mixed fabrics in only 49 minutes, using the
full load of the washing machine, at 40°C
(or less) temperature. This programme is
particularly suited to slightly dirty fabrics.
Rinse
This program performs 3 rinses with an
intermediate spin (which can be reduced or
excluded by using the appropriate button) . It
is used for rinsing any type of fabric, for
example after a wash carried out by hand.
Wool & Silk
This programme allows a delicate washing
cycle, particularly suited to garments specified
as "Machine-Washable" Wool fabrics and
laundry items made from Silk or specified as
"Wash as Silk" on the fabric label.
Cottons
This program is suitable to clean normally soiled
cotton laundry and it is the most efficient program
in terms of combined energy and water
consumptions for washing cotton laundry.
Rapid (14-30-44 Min.)
Washing cycle suggested for low loads and
slightly dirty. With this program it is
recommended to reduce the quantity of
detergent normally used, in order to avoid
unnecessary waste. Selecting the RAPID
program and acting on the button you can
choose one of three programs available.
DRYING
WARNING:
Dispensers used for concentrated powders
and liquid detergents must be removed
from the drum before commencing the
tumble drying programmes.
The drum changes direction during the
drying cycle to prevent the laundry from
tangling and producing even more drying.
Cool air is used during the last 10/20 minutes
of the drying cycle to minimize creasing.
Wool
Low temperature drying programme, ideal
to dry woollen clothes with maximum care
and softness, reducing rubbing of fabrics
and avoid possible felting. It’s suggested to
reverse clothing before drying. Timing is related
to the amount of the washing and the spin
speed selected for the wash. The cycle is
suitable for small loads up to 1 kg (3 sweaters).
Mixed (Low Heat)
Low
temperature
drying
programme
recommended for synthetics and mixed
fibres (always refer to the laundry care label).
ONE Fi EXTRA
Position that you have to select when you
want to enable remote control through the
App (via Wi-Fi). In this case, the start of
cycle will take place through the App
commands. If the machine is not enrolled
on
the
app
yet,
pressing
the
START/PAUSE button on the appliance will
perform the "Auto-Hygiene" cycle, made
to clean the drum. Designed to sanitize the
drum, remove bad smells and extend the
life of the appliance, make sure there is no
load in the drum before starting the "AutoHygiene" cycle and use a proprietary
washing machine cleaning agent or powder
detergent. Leave the door of the machine
open at the end of the cycle to allow the
drum to dry. Recommended every 50
washes.
The wool drying cycle of this machine
has been approved by "The Woolmark
Company" for the drying of machine
washable wool products provided that
the products are washed and dried
according to the instructions on the
garment label and those issues by the
manufacturer of this machine.
The
Woolmark
symbol
is
a
Certification mark in many countries.
M1715.
Cottons (High Heat)
High temperature drying programme
recommended for cottons and linen items
(always refer to the laundry care label).
23
EN
Drain & Spin
The program completes the drain and a
maximum spin. It is possible to delete or
reduce the spin with the SPIN SPEED button.
7. DRYING CYCLE
The correct way to dry
l Drying guidance advice is general, but
l Open the door.
practical experience of using the product
will help you to achieve the best drying
results.
l We recommend setting a lower drying
time than indicated, when first using the
appliance in order to establish the degree
of dryness required.
l We recommend not drying fabrics that
fray easily, such as rugs or garments with
a deep pile, in order to avoid air duct
clogging.
l We recommend that you sort the laundry
by the following methods:
- By drying care symbols, which are
displayed on the clothing labels
Suitable for tumble drying.
maximum drying load indicated in the
programme table. For large items (e.g.
sheets) or very absorbent items (e.g.
towels or jeans), it is a good idea to
reduce the load.
l Close the door.
l Press for at least 1 second the button of
a selected programme to switch on the
appliance.
l Press
the DRYING PROGRAMME
SELECTION button to select the more
laundry.
l The washer dryer can perform the
following types of drying:
- Low temperature drying programme
recommended for wool fabrics.
Tumble dry at high temperature.
- High temperature drying programme
recommended
for
cotton,
terry
toweling, linen, hemp fabrics, etc....
Tumble dry at low temperature only.
DO NOT tumble dry.
If the fabric does not have a care label,
you should assume that it is not
suitable for drying.
- Low temperature drying programme
recommended
for
mixed
fabrics
(synthetics/cotton) synthetic fabrics.
- By size and thickness
Whenever the wash load is bigger than
the drying capacity, separate the clothes
according to thickness (e.g. towels from
thin underwear).
- By fabric type
Cottons/linen: towels, cotton jersey, bed
and table linen.
Synthetics: blouses, shirts, overalls, etc.
made of polyester or polyamide, as well
as for cotton/synthetic mixes.
l Only dry pre-spun laundry.
24
l Fill with the laundry, not exceeding the
l Press the DRYING SELECTION button to
select the degree of dryness that you
require, choosing one of 3 automatic
programmes:
EXTRA DRY
(suitable for towels, bathrobes and
bulky loads).
IRON DRY
(that leaves the laundry ready for
ironing).
CUPBOARD DRY
(for items that will be put away
without ironing).
l The drying programme indicator will be
programme,
press
the
DRYING
SELECTION button until the required
time indicator lights up.
on, until the cool down phase begins and
the corresponding indicator is on.
l When the programme is finished the word
"End" will appear on the display. After
5 minutes the appliance will go into
standby mode (on certain models, the
display will show two lines).
By
selecting
the
wool
drying
programme, it's not possible to select
a degree of dryness different from the
default one.
l Press for at least 3 seconds the OFF
button to switch off the appliance.
l The washer dryer will calculate the time
needed for drying and the level of
moisture remaining in the laundry,
according to the load and drying type
selected.
l Check that the tap is turned on and that
the discharge
correctly.
hose
is
positioned
l Open the door and remove the laundry.
l Turn off the tap.
CANCELLING THE DRYING PROGRAMME
l To cancel the drying programme, press
and hold the DRYING SELECTION
button for about 3 seconds.
WARNING:
WARNING:
Do not dry articles with special
padding (e.g. quilts, quilted anoraks,
etc.) and very delicate fabrics.
If garments are drip/dry, load less
items to prevent creasing.
l Press the START/PAUSE button (the
display will
remaining).
show
the
drying
time
After cancelling the drying programme,
the cool down phase will begin and you
must wait for about 10/20 minutes
before opening the door.
In order to ensure the correct operation
of the appliance, it is advisable not to
interrupt the drying phase unless it is
absolutely necessary.
The appliance calculates the time to
the end of the selected programme
based upon a standard loading.
During the cycle, the appliance
corrects the time according to the size
and composition of the load.
During the drying phase the drum will
accelerate to a higher speed to
distribute the load and to optimize the
drying performance.
25
EN
l If you wish to select a timed drying
l If you wish to select a timed drying
8. AUTOMATIC
WASHING/DRYING
CYCLE
programme,
press
the
DRYING
SELECTION button until the required
time indicator lights up.
l Press the START/PAUSE button.
You cannot exceed the maximum
dryable load of laundry indicated in
the programme table, otherwise the
laundry will not be dried satisfactory.
l At the end of the wash phase the display
will show the drying time remaining.
- Washing
l Open the drawer and put in the correct
amount of detergent.
l Refer to the list of washing programmes
for the fabrics to be washed (e.g. very
dirty cotton) and turn the selector knob to
the required programme.
l Adjust
the
necessary.
wash
temperature
if
l The drying programme indicator will be
on, until the cool down phase begins and
the corresponding indicator is on.
l When the programme is finished the word
"End" will appear on the display. After 5
minutes the appliance will go into
standby mode (on certain models, the
display will show two lines).
l Press for at least 3 seconds the OFF
button to switch off the appliance.
l Press the option buttons (if required).
l Open the door and remove the laundry.
l Check that the tap is turned on and that
l Turn off the tap.
the discharge
correctly.
hose
is
positioned
CANCELLING THE DRYING PROGRAMME
- Drying
l Press the DRYING SELECTION button to
select the degree of dryness that you
require, choosing one of 3 automatic
programmes:
EXTRA DRY
(suitable for towels, bathrobes and
bulky loads).
IRON DRY
(that leaves the laundry ready for
ironing).
CUPBOARD DRY
(for items that will be put away
without ironing).
By selecting the wool programme,
only the default degree of dryness is
available.
26
l To cancel the drying programme, press
and hold the DRYING SELECTION
button for about 3 seconds.
WARNING:
After cancelling the drying programme,
the cool down phase will begin and you
must wait for about 10/20 minutes
before opening the door.
In order to ensure the correct operation
of the appliance, it is advisable not to
interrupt the drying phase unless it is
absolutely necessary.
If you believe the washing machine is not working correctly, consult the quick guide
provided below which includes some practical tips on how to fix the most common
problems.
ERROR CODE FORMAT
l Models with a display: the error is shown by a number preceded by the letter “E”
(example: E2 = Error 2).
l Models without display: an error is shown by a sequence of flashes of every LED.
The error code is shown by the number of flashes followed by a pause of 5 seconds
(example: two flashes – pause 5 seconds – two flashes – repeating = Error 2).
Error shown
E2 (with display)
2 flashes of the LEDs
(without display)
Possible causes and practical solutions
The machine cannot load water.
Make sure the water supply tap is open.
Make sure the water supply hose isn’t bent, kinked or trapped.
Make sure the drain pipe is at the proper height (see installation section).
E3 (with display)
3 flashes of the LEDs
(without display)
E4 (with display)
4 flashes of the LEDs
(without display)
E7 (with display)
7 flashes of the LEDs
(without display)
Any other code
Close the water supply tap, unscrew the filler hose from the back of
the washing machine and make sure the “anti-sand” filter is clean
and not blocked.
Check that the filter is not clogged or that there are no foreign bodies
inside the filter compartment that can obstruct the proper flow of
water.
The washing machine does not drain water.
Check that the filter is not clogged or that there are no foreign bodies
inside the filter compartment that can obstruct the proper flow of
water.
Make sure the drain hose isn’t bent, kinked or trapped.
Make sure the home drainage system is not blocked and is allowing
water to flow through without obstruction. Try to drain the water in the sink.
There is too much foam and/or water.
Ensure the correct amount of detergent is being used and the
detergent is designed for use in a washing machine.
Door problem.
Make sure the door is correctly closed.
Make sure the clothes inside the drum are not preventing the door
from closing fully.
If the door is locked, turn off and unplug the washing machine from
the electrical supply socket, wait 2-3 minutes and reopen the door.
Turn off and unplug the washing machine, wait a minute. Turn on the
machine and restart a program. If the error occurs again contact an
Authorised Customer Service Centre directly.
27
EN
9. THROUBLESHOOTING AND WARRANTY
OTHER ANOMALIES
Problem
Possible causes and practical solutions
The washing machine
does not work / start
The washing machine
does not spin
Make sure the product is plugged into a working supply socket.
Make sure power is on.
Make sure the wall socket is working, testing it with another
appliance such as a lamp.
The door may not be correctly closed: open and close it again.
Check whether the required program was correctly selected and the
start button pressed.
Make sure the washing machine is not in pause or time delay mode.
This may be due to a leak from the seal between the tap, supply
hose and fill valve; in this case, replace it and tighten the hose
connections correctly.
Make sure the front filter is correctly closed.
The machine is fitted with a detection system that protects the load
and product from damage if the load is not balanced before spinning.
This may result in:• The machine attempts to balance the load, increasing the time of
spin.
• Reduction of the speed of spin to decrease vibrations and noise.
• The spin cycle aborting to protect the machine and load.
If this is experienced remove the load de-tangle it, reload it and
restart the spin program.
This could be due to the fact that water has not been completely
drained: wait a few minutes. If the problem persists, see Error 3
section.
Some models include a "no spin" function: make sure it is not
selected.
Check which options are selected and their effect on the spin cycle.
Strong vibrations /
noises are heard
during the spin cycle
Excessive detergent can impede the spin cycle, ensure the correct
amount of detergent is being used.
The washing machine may not be fully levelled: if necessary, adjust
the feet as indicated in the specific section.
Make sure transport screws, rubber bungs and spacer tubes were
removed.
Make sure there are no foreign objects inside the drum (coins,
hinges, buttons, etc…).
Water leaked on the
floor near the
washing machine
The standard manufacturer warranty covers faults caused by electrical or
mechanical faults in the product due to an act or omission of the manufacturer. If
a fault is found to be caused by factors outside the product supplied, miss-use or
as a result of the instructions on use not being followed, a charge may be
applied.
28
Warranty
The product is guaranteed under the
terms and conditions stated on the
certificate included with the product. The
certificate has to be stored so as to be
shown to the Authorized Customer
Service Centre in case of need. You can
also check the warranty conditions on
our web site. To obtain assistance,
please fill in the form on-line or contact
us at the number indicated on the
support page of our web site.
- cloudier rinse drain water: This effect is
tied to the suspended zeolites which do
not have negative effects on rinse
efficiency.
- white powder (zeolites) on laundry at
the end of the wash: this is normal, the
powder is not absorbed by fabric and
does not change its colour.
To remove the zeolites, select a rinse
programme. In the future consider using
slightly less detergent.
- foam in the water at last rinse: this
does not necessary indicate poor rinsing.
Consider using less detergent in future
washes.
- abundant foam: This is often due to the
anionic surfactants found in the
detergents which are hard to eliminate
from laundry.
In this case, do not re-rinse to eliminate
these effects: it will not help at all.
We suggest conducting a maintenance
wash using a proprietary cleaner.
If the problem persists or if you suspect a
malfunction, immediately contact an
Authorised Customer Service Centre.
It is always recommended to use original
spare parts, that are available at our
Authorised Customer Service Centres.
By placing the
mark on this
product, we are confirming compliance to
all relevant European safety, health and
environmental requirements which are
applicable in legislation for this product.
The manufacturer declines all
responsibility for any printing errors in
the booklet included with this product.
Moreover, it also reserves the right to
make any changes deemed useful to its
products without changing their essential
characteristics.
29
EN
The use of ecological detergents without
phosphates may cause the following effects:
fkhldsk
fkhldsk
- WDWFT - AH -
18.10 - 43018768.A - Canon Italia - Business Services Channel
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising