Hoover | WDXT45 385A/1-S | Hoover WDXT45 385A/1-S User manual

Hoover WDXT45 385A/1-S User manual
EN
2
Thank-you for choosing a Hoover washing
machine. We are proud to always offer
new,
innovative
and
technologically
advanced products, with a complete range
of home appliances to ensure true
assistance in your daily routine.
This appliance is marked according to
the European directive 2012/19/EU
on Waste Electrical and Electronic
Equipment (WEEE).
WEEE contains both polluting substances (which
can cause negative consequences for the
environment) and basic components (which can
be re-used). It is important to have WEEE
subjected to specific treatments, in order to
remove and dispose properly all pollutants, and
recover and recycle all materials. Individuals can
play an important role in ensuring that WEEE
does not become an environmental issue; it is
essential to follow some basic rules:
We suggest you register your product at
www.registerhoover.com to gain faster
access to supplementary services solely
reserved to our most loyal customers.
Carefully read this manual for correct and
safe appliance use and for helpful tips on
efficient maintenance.
l WEEE should not be treated as household
waste;
Only use the washing machine
after carefully reading these instructions.
We recommend you always keep this
manual on hand and in good condition for
any future owners.
l WEEE should be handed over to the relevant
collection points managed by the municipality or
by registered companies. In many countries, for
large WEEE, home collection could be present.
In many countries, when you buy a new
appliance, the old one may be returned to the
retailer who has to collect it free of charge on a
one-to-one basis, as long as the equipment is of
equivalent type and has the same functions as
the supplied equipment.
Please check that the appliance is
delivered with this instruction manual,
warranty certificate, service centre address
and energy efficiency label. Also check that
plugs, drain hose support hook and liquid
detergent or bleach tray (only on some
models) are included. We recommend you
keep all these components.
Contents
1. GENERAL SAFETY RULES
Each product is identified by a unique 16character code, also called the “serial
number”, printed on the sticker. This can be
found inside the door opening. This code is
a unique code for your product that you will
need to register the product warranty, or if
you need to contact the Customer Service
Centre.
2. INSTALLATION
3. PRACTICAL TIPS
4. MAINTENANCE AND CLEANING
5. QUICK USER GUIDE
6. CONTROLS AND PROGRAMS
7. DRYING CYCLE
8. AUTOMATIC WASHING/DRYING CYCLE
9. THROUBLESHOOTING AND WARRANTY
3
EN
Environmental conditions
in a safe way and understand the
hazards involved.
Children shall not play with the
appliance. Cleaning and user
maintenance shall not be made
by children without supervision.
1. GENERAL SAFETY
RULES
l This
appliances is intended to
be used in household and
similar applications such as:
- Staff kitchen areas in shops, offices
and other working environments;
- Farm houses;
- By clients in hotels, motels and
other residential type environments;
- Bed and breakfast type environments.
A different use of this appliance
from household environment
or from typical housekeeping
functions, as commercial use by
expert or trained users, is excluded
even in the above applications. If
the appliance is used in a manner
inconsistent with this it may reduce
the life of the appliance and may
void the manufacturer’s warranty.
Any damage to the appliance or
other damage or loss arising
through use that is not consistent
with domestic or household use
(even if located in a domestic or
household environment) shall not
be accepted by the manufacturer to
the fullest extent permitted by law.
l Children
should be supervised
to ensure that they do not play
with the appliance.
l Children
of less than 3 years
should be kept away unless
continuously supervised.
l If
the supply cord is damaged, it
must be replaced by the
manufacturer, its service agent
or similarly qualified persons in
order to avoid a hazard.
l Only
use
the
hose-sets
supplied with the appliance for
the water supply connection
(do not reuse old hose-sets).
l Water
pressure must be between
0.05 MPa and 0.8 MPa.
l Make
sure carpets or rugs do
not obstruct the base or any of
the ventilation openings.
appliance can be used by l The OFF condition is reached
by placing the reference mark on
children aged from 8 years and
the programmes control/knob in
above and persons with reduced
the vertical position. Any other
physical, sensory or mental
different position of such control
capabilities or lack of experience
sets the machine in ON condition
and knowledge if they have been
(only for models with programmes
given supervision or instruction
knob).
concerning use of the appliance
l This
4
final part of a washer dryer l Items that have been soiled with
cycle occurs without heat (cool
substances such as cooking oil,
down cycle) to ensure that the
acetone, alcohol, petrol, kerosene,
items are left at a temperature
spot removers, turpentine, waxes
that ensures that the items will
and wax removers should be
not be damaged.
washed in hot water with an extra
amount of detergent before being
dried in the washer dryer.
WARNING:
never stop a washer dryer before l Items such as foam rubber
(latex foam), shower caps,
the end of the drying cycle
waterproof textiles, rubber
unless all items are quickly
backed articles and clothes or
removed and spread out so that
pillows fitted with foam rubber
the heat is dissipated.
pads should not be dried in the
washer dryer.
l After installation, the appliance
must be positioned so that the l Fabric softeners, or similar
products, should be used as
plug is accessible.
specified by the fabric softener
instructions.
l The appliance must not be
installed behind a lockable
door, a sliding door or a door l Oil-affected items can ignite
spontaneously, especially when
with a hinge on the opposite
exposed to heat sources such
side to that of the washer
as a washer dryer. The items
dryer, in such way that a full
become warm, causing an
opening of the washer dryer
oxidation reaction in the oil,
door is restricted.
Oxidation creates heat. If the
heat cannot escape, items can
l The maximum load capacity of
become hot enough to catch
dry clothes depends on the
fire. Piling, stacking or storing
model used (see control panel).
oil-effected items can prevent
l The appliance is not to be used
heat from escaping and so
if industrial chemicals have
create a fire hazard.
been used for cleaning.
l If it is unavoidable that fabrics
contain vegetable or cooking
l Do not dry unwashed items in
oil or have been contaminated
the washer dryer.
5
EN
l The
by hair care products be l Do not pull on the power cord
placed in a washer dryer they
or appliance to unplug the
should first be washed in hot
machine.
water with extra detergent this will reduce, but not l Do not expose the washing
machine to rain, direct sunlight
eliminate, the hazard.
or other weather elements.
l Remove
all objects from
Protect from possible freezing.
pockets such as lighters and
l When moving, do not lift the
matches.
washing machine by the knobs
l To consult the product technical
or detergent drawer; during
specification please refer to the
transport, never rest the door on
manufacturer website.
the trolley. We recommend two
people lift the washing machine.
Safety instructions
l In
the event of fault and/or
malfunction, turn off the
washing machine, close the
water tap and do not tamper
with the appliance.
Immediately
contact
the
Customer Service Centre and
only use original spare parts.
Failure to observe these
instruction may jeopardise
appliance safety.
l Before
cleaning or maintaining
the washing machine, unplug
the appliance and turn off the
water tap.
l Make
sure the electrical system
is earthed. Otherwise, seek
qualified professional assistance.
l Please
do not use converters,
multiple sockets or extension
cords.
WARNING:
water may reach very high
temperatures during the
wash cycle.
By placing the
mark on this
product, we are confirming
compliance to all relevant
European safety, health and
l Make sure there is no water in environmental requirements which
the drum before opening the are applicable in legislation for
door.
this product.
6
2. INSTALLATION
l Release
the power chord and
drain hose from the securing
clip at the rear of the machine.
l Remove the 2 or 4 transportation
screws (A) on the back and
remove the 2 or 4 flat washers,
rubber bungs and plastic spacer
tubes (B) as illustrated in figure 1.
l If the washing machine is built-in,
unscrew the 3 or 4 transportation
screws (A) and remove the 3 or
4 flat washers, rubber bungs and
plastic spacer tubes (B).
l During the removal of the screws
occasionally spacer tubes fall
inside the product, these can be
remove by tilting the product forward
and recovering them from the floor
or inside the base of the machine.
l Cover the open transportation
screw holes with the 2 or 4
plastic caps included in the
instruction bag.
A
B
A
B
B
B
EN
1
A
A
2
A
1
2
3
B
WARNING:
keep packaging materials
away from children.
l Place
the corrugated plastic
sheet, found on top of the
appliance during the unpacking
process, into the base of the
appliance as shown in figure 2
(according to the model,
consider version A, B or C).
C
3
2
7
1
Hydraulic connections
3
l Connect the water hose to the water
supply tap (fig. 3) only using the hose
supplied with the appliance (do
not
reuse old hose-sets).
l Some models may include one or more of
the following features:
l HOT&COLD (fig. 4):
water mains connection settings with hot
and cold water for higher energy savings.
Connect the grey tube to the cold water
tap
and the red one to the hot water
tap. The machine can be connected to
the cold water tap only: in this case, some
programs may start a few minutes later.
4
1
l AQUASTOP (fig. 5):
a device located on the supply tube that
stops water flow if the tube deteriorates;
in this case, a red mark will appear in the
window “A” and the tube must be
replaced. To unscrew the nut, press the
one-way lock device "B".
5
6
B
l AQUAPROTECT – SUPPLY TUBE WITH
GUARD (fig. 6):
Should water leak from the primary
internal tube "A", the transparent
containment sheath "B" will contain water
to permit the washing cycle to complete.
At the end of the cycle, contact the
Customer Service Centre to replace the
supply tube.
A
B
A
7
Setting
l The washing machine should be installed
in its final position such that the water fill
hose is not kinked or trapped. The
corrugated drain hose should be inserted
into suitable drain pipe of between 50 cm
and 85 cm height above the floor using
the curved drain hose support. If an under
sink connection is used the drain hose
must be routed above the sink overfill
opening to prevent back siphoning. Care
must be taken to avoid kinking or trapping
the drain hose (fig. 7).
max 100 cm
min 4 cm
8
+2,6 mt
max
min 50 cm
max 85 cm
l Level the appliance using the feet as
EN
8
illustrated in figure 8:
a. turn the nut clockwise to release the
screw;
b. rotate the foot to raise or lower it until it
touches to the floor;
c. lock the foot, screwing in the nut, until it
tightens against to the bottom of the
washing machine.
l Plug in the appliance.
A
B
WARNING:
contact the Customer Service Centre
should
the
power
cord
need
replacement.
C
Detergent drawer
9
1
The detergent draw is split into 3
compartments as illustrated in figure 9:
l compartment "1": for prewash detergent;
l compartment “ ”: for special additives,
softeners, starch fragrances, etc.;
2
WARNING:
only use liquid products; the washing
machine is set to automatically dose
additives at each cycle during the last
rinse.
10
l compartment "2": for washing detergent.
A liquid detergent cup is also included IN
SOME MODELS (fig. 10). To use it, place it
in compartment "2". This way, liquid
detergent will only enter the drum at the
right time. The cup can also be used for
bleach when the “Rinse” program is
selected.
11
WARNING:
some detergents are hard to remove.
In this case we recommend using the
specific container to be placed in the
drum (example in figure 11).
9
reduce the necessity of a hot wash
programme.
Save up to 50% energy by using a 60°C
wash programme.
3. PRACTICAL TIPS
Load tips
WARNING: when sorting laundry, make
sure:
- have eliminated metallic objects such as
hair clips, pins, coins, from laundry;
- to have buttoned pillow cases, closed
zips, tied loose belts and long robe
ribbons;
- to have removed rollers, hooks or clips
from curtains;
- to have carefully read clothing washing
labels;
- to have removed any persistent stains
using specific detergents.
l When washing rugs, bedcovers or other
heavy clothing, we recommend you avoid
the spinning cycle.
l To wash wool, make sure the item can be
machine washed and marked by the
“Pure virgin wool” symbol with the “Does
not mat” or “Machine washable” label.
Helpful suggestions for the user
A guide environmentally friendly and
economic use of your appliance.
Maximise The Load Size
l Achieve the best use of energy, water,
detergent and time by using the
recommended maximum load size.
Save up to 50% energy by washing a full
load instead of 2 half loads.
Do you need to pre-wash?
l For heavily soiled laundry only!
SAVE detergent, time, water and
between 5 to 15% energy consumption
by NOT selecting Prewash for slight to
normally soiled laundry.
Is a hot wash required?
l Pretreat stains with stain remover or soak
dried in stains in water before washing to
10
Before using a drying programme…
l SAVE energy and time by selecting a
high spin speed to reduce the water
content in laundry before using a drying
programme.
Following is a quick guide with tips and
recommendations on detergent use at the
various temperatures. In any case, always
read the instructions on the detergent for
correct use and doses.
When washing heavily soiled whites,
we
recommend
using
cotton
programs of 60°C or above and a
normal washing powder (heavy duty)
that contains bleaching agents that at
medium/high
temperatures
provide
excellent results.
For washes between 40°C and 60°C
the type of detergent used needs to be
appropriate for the type of fabric and
level of soiling.
Normal powders are suitable for “white”
or colour fast fabrics with high soiling,
while liquid detergents or “colour
protecting” powders are suitable for
coloured fabrics with light levels of
soiling.
For washing at temperatures below
40°C we recommend the use of liquid
detergents or detergents specifically
labeled as suitable for low temperature
washing.
For washing wool or silk, only use
detergents specifically formulated for
these fabrics.
To clean the washing machine exterior, use
a damp cloth, avoiding abrasives, alcohol
and/or solvents. To maintain a good wash
performance we recommend that the soap
drawer and pump filters are regularly
cleaned. A monthly service wash, using a
proprietary cleaner is also recommended.
finished, replace it turning it clockwise.
The filter handle will be locked when it is
not possible to turn any further and the
handle is horizontal. Smearing a small
amount of liquid soap on the filter seal will
help refitting.
l Repeat the previous steps in reverse
order to reassemble all parts.
Drawer cleaning
l We recommend you clean the drawer to
avoid accumulating
additive residue.
detergent
and
l To do this, extract the drawer using slight
force, clean it with running water and
reinsert it in its housing.
S u g g e s tio n s fo r m o v e s o r
prolonged disuse
l Ensure the siphon cap is correctly
refitted.
Filter cleaning
l The washing machine comes with a
special filter able to trap large residue,
such as buttons or coins, which could
clog the drain.
l Should the washing machine be stored in
an unheated room for a long period of
time, drain all water from tubes.
l Unplug the washing machine.
l Detach the tube from the drainage
l Only available on certain models: pull out
system and clip on the rear of the
machine and lower it, fully draining water
into a bowl.
the corrugated hose, remove the stopper
and drain the water into a container.
l Secure the drain tube with the drainage
l Ensure all the water has been emptied
from the drum.
system and clip on the rear of the
machine when finished.
l Keep the door glass and gasket clean.
l Before
unscrewing the filter, we
recommend you place an absorbent cloth
under it to keep the floor dry. A small
amount of water will come out of the filter
as you remove it - this is normal.
The manufacturers warranty only
covers faults within the product of a
mechanical or electrical nature.
Faults
caused
by
handling,
installation or miss use are not
covered and may incur a charge for
any repair visit to resolve.
l Turn the filter counter-clockwise to the
limit stop.
11
EN
l Remove and clean the filter; when
4. MAINTENANCE AND
CLEANING
5. QUICK USER GUIDE
This washing machine automatically adjusts
the level of the water to the type and
quantity of washing. This system gives a
reduction in energy consumption and a
saving in washing times.
6. CONTROLS AND
PROGRAMS
Q
}
Program selection
A
l Turn on the washing machine and select
the required program.
l Adjust
the washing temperature if
necessary and press the required "option"
buttons.
DRYING
If you would like the drying cycle to
begin automatically after washing,
select the programme required using
the DRYING SELECTION button.
Or you can finish the wash and then
select the drying programme and
load size.
P
O
F
B
D
C
G
H
I
L
M
N E
A Touch Control (with ON/OFF
button)
l Press the START/PAUSE button to start
washing.
l At the end of the programme, the
message "End" will appear on the display
or, on some models, all wash stage
indicator lights will turn on.
Wait until the DOOR LOCKED light has
gone out before opening the door.
l Turn off the washing machine.
For any type of wash, see the program
table and follow the operating sequence
as indicated.
Technical data
Water pressure:
min 0.05 Mpa / max 0.8 Mpa
(0.05 MPa dispenses approximately 1 litre
of water in 10 seconds)
Spin r.p.m.: See rating plate.
Power input / Power current fuse amp /
Supply voltage: See rating plate.
12
B START/PAUSE button
C SPIN SPEED button
D TEMPERATURE SELECTION
button
E
F
G
H
I
L
M
N
O
P
Q
DELAY START button
WASH TIME button
PREWASH button
HYGIENE PLUS button
EXTRA RINSE button
DRYING SELECTION button
FAVOURITES button
NIGHT & DAY button
Digital display
DOOR LOCKED indicator light
DRYING PROGRAMME
SELECTION button
E+N KEY LOCK
Opening the door
A special safety device prevents the
door from being opened immediately
after the end of the cycle.
Wait for 2 minutes after the wash
cycle has finished and the "Door
Security" light has gone out before
opening the door.
2) PROGRAMME SELECTION button
Turning on the appliance is also possible by
pushing for at least one second the button
of a selected programme (the display will
light up, showing the parameters of the
selected cycle).
To set another programme, press the
related button (the corresponding indicator
light will light up).
To switch off the appliance, press the
ON/OFF button (for at least 3 seconds).
Touch Control
3) BUTTON SELECTION indicators
They light up at the touch of the related
button.
4) "X Red Light"
1) ON/OFF button
Press for at least 1 second the ON/OFF
button to turn on the appliance.
Switching on, the related indicator will light
on, as well as the "X Red Light", waiting
for the selection of a washing programme.
It lights up at the pressing of any button of
the Touch Control, with a diffused lighting
fading to the edges.
It gradually turns off within 5 minutes since
the last touch of a button, in order to save
energy.
13
EN
WARNING:
Don’t touch the display (and the Touch
Control) while inserting the plug because
the machines calibrates the systems
during the first seconds: touching the
display, the machine couldn’t work
property. In this case, remove the plug
and repeat the operation.
If a programme is not selected within 30
seconds, the appliance will automatically
turn off.
Waiting for the selection of the programme
the display is off.
START/PAUSE button
SPIN SPEED button
l By pressing this button, it is possible to
reduce the maximum speed, and if you
wish, the spin cycle can be cancelled.
Close the door BEFORE selecting the
button START/PAUSE.
spin speed cancelled.
l Press to start the selected cycle.
l To reactivate the spin cycle press the button
until you reach the spin speed you would
like to set.
When the START/PAUSE button has
been pressed, the appliance can take
few seconds before it starts working.
ADD OR REMOVE ITEMS AFTER THE
PROGRAMMES HAS STARTED (PAUSE)
l Press and hold the START/PAUSE
button for about 2 seconds (some
indicator light and the time remaining
indicator will flash, showing that the
machine has been paused).
l Wait 2 minutes until the safety device
unlocks the door.
l After you have added or removed items,
close the door and press the
START/PAUSE button (the programme
will start from where it left off).
To prevent damage to the fabrics, it is
not possible to increase the speed
over that which is automatically
suitable during the selection of the
program.
l It is possible to modify the spin speed
without pausing the machine.
The machine is fitted with a special
electronic device, which prevents the
spin cycle should the load be
unbalanced.
This reduces the noise and vibration in
the machine and so prolongs the life of
your machine.
TEMPERATURE SELECTION button
l This button allows you to change the
CANCELLING THE PROGRAMME
temperature of the wash cycles.
l To cancel the programme, press the
ON/OFF button (for at least 3 seconds).
cold wash.
l It is not possible to raise the temperature
over the maximum allowed for every
programme, in order to save the fabrics.
The option buttons should be selected
before pressing the START/PAUSE
button.
If an option is selected that is
not compatible with the selected
programme then the option indicator
first flashes and then goes off.
DELAY START button
l This button allows you to pre-programme
the wash cycle to delay the start of the
cycle for up to 24 hours.
14
l We recommend you use only 20% of the
procedure:
recommended quantities shown on the
detergent pack.
- Set the required programme.
- Press the button once to activate it (h00
appears on the display) and then press
it again to set a 1 hour delay (h01
appears on the display). The pre-set
delay increases by 1 hour each time the
button is pressed, until h24 appears on
the display, at which point pressing the
button again will reset the delay start to
zero.
- Confirm by pressing the START/PAUSE
button (the light on the display starts to
flash). The countdown will begin and
when it has finished the programme will
start automatically.
HYGIENE PLUS button
With this option it is possible to hygienize
the clothes, the washing programme
reach a temperature of 60°C.
EXTRA RINSE button
l This button allows you to add rinses at
the end of the washing cycle. The
maximum number of extra rinses is
related to the programme selected.
l This function has been studied for the
people with delicate and sensitive skin,
for which also a least residue of detergent
can cause irritations or allergies.
l It is possible to cancel the delay start by
pressing the ON/OFF button (for at least
3 seconds).
If there is any break in the power supply
while the machine is operating, a special
memory stores the selected programme
and, when the power is restored, it
continues where it left OFF
l It advises to also use this function for the
children items and in case of washings of
very dirty items, for which it is due to use
a lot of detergent, or in the washing of
toweling items whose fibres mostly have
the tendency to hold the detergent.
WASH TIME button
DRYING SELECTION button
l By selecting this button there is a choice
of 3 levels of wash intensity, depending
on how much the fabrics are soiled (can
be used only on some programmes as
shown in the table of programmes).
l This button allow to select the required
degree (or time) of drying programme: an
indicator light will light to display the
drying result selected each time you
press the button.
l Once the programme has been selected
the indicator light will automatically show
the wash time set for that programme.
l To cancel the selection before the start of
a drying programme, press the button
repeatedly until the indicators go out.
l Selecting a different wash time the
relevant indicator will light up.
l To cancel the cycle during the drying
phase, press and hold the button for at
least 3 seconds.
PREWASH button
l This option allows you to make a prewash
and it is particularly useful for heavily
soiled loads (can be used only on
some programmes as shown in the
table of programmes).
Given the high temperature inside the
drum, the machine will execute a cool
down phase before to unlock the door,
so the laundry can't be removed until
the end of this phase.
15
EN
l To delay the start use the following
FAVOURITES button
NIGHT & DAY button
This function allows you to save the settings
of your two favourite personalised
programmes, including the temperature,
spin speed and soil level, so you can recall
them quickly.
l This option reduces the intermediate spin
How to memorize a programme for the
first time:
1)
Select the programme
options you want.
2)
Press the FAVOURITES button,
choosing either M1 or M2. You should
choose M1 if this is the first
programme you have saved.
3)
and
l Deselect the option to end the cycle with
a spin dry (which may be reduced or
cancelled using the appropriate button)
and emptying phase.
Keep
your
finger
on
the
FAVOURITES button for about 3
seconds to save the combination in
the chosen position.
l Thanks to electronic control, the water in
Memorize a new programme when M1 &
M2 already have programmes saved:
Set the programme and the options
you want.
2)
Press the FAVOURITES button for
about 3 seconds to save the
combination in the position M1. The
pre-existing saved programme in M1
will move in the position M2.
Start a program
memorized
that
is
l During the phase in which the water is
held in the tub, the relevant indicator light
blink to show that the machine is at a
standstill.
the
1)
speed to 400 rpm, where applicable,
increase the water level during rinsing
and keep the laundry immersed in water
after the final rinse, in order to spread the
fiber perfectly.
the intermediate phases is emptied
silently, making this option very useful for
washing at night.
DRYING PROGRAMME SELECTION
button
This button allows you to select one of three
drying programmes available. By pressing
this button, one indicator light will go on to
show the selected drying programme.
already
l Press briefly the FAVOURITES button
(once for M1, twice for M2) and press the
START/PAUSE button.
l Once you recall a memorized program,
you can still change its options and
settings, pressing the corresponding
keys. In this case, the added options
won’t be memorized.
KEY LOCK
l Pressing
simultaneously the buttons
NIGHT & DAY and DELAY START for
about 3 seconds, the machine allows
you to lock the keys.
In this way, you can avoid making
accidental or unwanted changes if a
button on the display is pressed
accidently during a cycle.
l The key lock can be simply cancelled by
If you accidently select a memorized
program, simply turn the program
knob to select another one.
pressing the two buttons simultaneously
again or by pressing the ON/OFF button
(for at least 3 seconds).
16
The display’s indicator system allows you to
be constantly informed about the status of
the machine.
1 15
6 10
16 12
5
This show the spin speed of the selected
programme that can be changed or omitted
by the relevant button.
spin speed cancelled.
3) WASH TEMPERATURE
3
This show the washing temperature of the
selected programme that can be changed
(where allowed) by the relevant button.
2
7
7
13 14
7
8
7
9 11
7
4
1) DOOR LOCKED INDICATOR LIGHT
l The indicator light is illuminated when the
cold wash.
4) CYCLE DURATION
l When a programme is selected the
display automatically shows the cycle
duration, which can vary, depending on
the options selected.
door is fully closed.
Close the door BEFORE selecting the
START/PAUSE button.
l Once the programme has started you will
be kept informed constantly of the time
remaining to the end of the wash.
l When START/PAUSE
is pressed on
the machine with the door closed, the
indicator will flash momentarily and then
illuminate.
l The appliance calculates the time to the
If the door is not properly closed,
the light will continue to flash for
about 7 seconds, after which the
start command will be automatically
delete. In this case, close the door
in the proper way and press the
START/PAUSE button.
l If automatic washing/drying is selected, at
l A special safety device prevents the door
from being opened immediately after the
end of the cycle. Wait for 2 minutes after
the wash cycle has finished and the
DOOR LOCKED light has gone out
before opening the door. At the end of the
cycle press the ON/OFF button (for at
least 3 seconds).
end of the selected programme based
upon a standard loading, during the cycle,
the appliance corrects the time to that
applicable to the size and composition of
the load.
the end of the wash phase, the drying time
remaining to the end will be shown on the
display.
5) WASH TIME
l Once the programme has been selected,
the indicator light will automatically show
the wash time set for that programme.
l Selecting a different wash time the
relevant indicator will light up.
17
EN
2) SPIN SPEED
Digital Display
6) EXTRA RINSES
The indicator lights show the extra rinses
selected by the relevant button.
7) OPTIONS
The indicator lights show the options that
can be selected by the relevant buttons.
8) Wi-Fi (some models only)
l In the models with the Wi-Fi option, the
icon indicates that the Wi-Fi system is
working.
l For all other information in the Wi-Fi
system, there is a specific manual inside
the machine.
9) DELAY START
- adjusts the spin speed according to the
load, thus avoiding any imbalance.
11) FAVOURITES
The indicator light show that the memory
function is working.
12) KEY LOCK
The indicator light show that the keys are
locked.
13) TAP CLOSED
Indicates that the machine is unable to load
the water: it is suggested to turn off the
machine, check that the tap is open and the
water pressure is not particularly low.
14) FILTER BLOCKED
This flashes when delay start has been set.
10) Kg MODE (function active only on
Cotton and Synthetics programmes)
l For the programmes where the "Kg
MODE" function is active, the appliance
in the first minutes it calculates the real
laundry loaded, updating the levels on the
display in real time.
Every levels shown on the display is the
20% of the maximum loading capacity.
When a programme is selected the
maximum capacity suggested is shown
on the display.
l Through every wash phase "Kg MODE"
allows to monitor information on the wash
load in the drum and in the first minutes
of the wash it:
- adjusts the amount of water required;
Indicates that the machine is not able to
drain the water: it is suggested to turn off
the machine, check that the filter is not
clogged or that the drain hose is not kinked
or crushed.
15) STANDARD COTTON PROGRAMMES
LIGHTS (see table of programmes)
The lights will light up when you select the
most efficient program in terms of water and
energy consumption, to wash cotton
garments with a normal grade of soil.
16) DRYING SELECTION INDICATORS
The indicators display the type of the drying
programme.
Automatic drying programmes
- determines the length of the wash cycle;
- controls rinsing according to the type of
fabric selected to be washed it;
Extra dry programme (suitable for
towels, bathrobes and bulky loads).
- adjusts the rhythm of drum rotation for
the type of fabric being washed;
Iron dry programme (that leaves the
laundry ready for ironing).
- recognizes the presence of lather,
increasing, if necessary, the amount of
water during rinsing;
Cupboard dry programme (for
items that will be put away without
ironing).
18
Cool down phase
programmes, the washer dryer will
calculate the time needed for drying and
the level of moisture remaining in the
laundry, according to the load and drying
type selected.
l After pressing the START/PAUSE button,
the display will show the drying time
remaining.
Activated during the final cool down
period, in the last 10/20 minutes of
each drying phase.
Useful tips
l The 30 minute drying programme is
The appliance calculates the time to
the end of the selected programme
based upon a standard loading.
During the cycle, the appliance
corrects the time according to the size
and composition of the load.
recommended for small loads (less than 1
kg) or only slightly damp loads.
l Your washer dryer automatically ends the
cycle when it reaches the selected drying
level.
Timed drying programmes
They may be used to select timed
drying programmes.
l In order to ensure the correct operation of
the appliance, it is advisable not to
interrupt the drying phase unless it is
absolutely necessary.
19
EN
l By selecting one of these automatic
Table of programmes
TEMP.°C
kg *
(MAX.)
PROGRAM
Recommended
Max.
All In One 20°C
2)
4
5,5
6
6,5
7
20°
20°
All Baby 60°C
2)
4
5,5
6
6,5
7
60°
60°
All In One 59 Min.
2)
6
8
9
10
11
40°
40°
1
2
2
2
2
30°
30°
-
-
-
-
-
-
-
Delicates
2
2,5
2,5
2,5
2,5
40°
40°
Acrylics
3
4
4,5
5
5,5
-
-
5
5
6
6
7
-
-
30°
30°
Wool & Silk
Rinse
1
2
2)
(drying)
Cottons
(drying)
Rapid W&D 59 Min. 1,5 1,5 1,5 1,5 1,5
DETERGENT
2
1
Mixed
1)
2)
3
4
4,5
5
5,5
40°
60°
( )
Cottons**
1)
2)
6
8
9
10
11
40°
90°
( )
Rapid 30 Min.
2)
2
2,5
2,5
2,5
2,5
30°
30°
Drain & Spin
2)
-
-
-
-
-
-
-
20
Please read these notes:
* Maximum load capacity of dry clothes,
according to the model used (see control
panel).
INFORMATION FOR THE
LABORATORIES (Ref. EN
Standards)
TEST
50229
( )
Only with PREWASH option
selected
(programmes
with
PREWASH option available).
Washing
Use the programme ** with the maximum
wash time selected, maximum spin speed
and a temperature of 60°C. Programme
recommended also for test with a lower
temperature.
(Only for models with liquid
detergent compartment)
When only a limited number of
articles have stains which require
treatment with liquid bleaching
agents, preliminary removal of
stain can be carried out in the
washing machine.
Pour the bleach into the liquid
bleach container, inserted into the
compartment marked "2" in the
detergent drawer, and set the
special programme RINSE.
When this phase has terminated,
switch off the appliance, add the
rest of the fabrics and proceed
with a normal wash on the most
suitable programme.
Drying
First drying with A kg (a load consist:
pillowcases and hand-towels) selecting
the
cotton
drying
programme
(
) cupboard dry (
).
Second drying with B kg (a load consist:
sheets and hand towels) selecting the
cotton drying programme (
cupboard dry (
)
).
Capacity
(washing)
(kg)
A (kg)
B (kg)
First
drying
Second
drying
6
5
1
8
5
3
9
6
3
10
6
4
11
7
4
21
1)
For the programmes shown you
can adjust the duration and
intensity of the wash using the
WASH TIME button.
2)
Programmes for automatic drying.
EN
The spin speed may also be reduced, to
match any guidelines suggested on the
fabric label, or for very delicate fabrics
cancel the spin completely this option is
available with a spin speed button. This
function can be activated with the button
SPIN SPEED.
If the label does not indicate specific
information, it is possible to use the
maximum spin expected in the program.
An over dosing of detergent can cause
excessive foaming.
If the appliance detects the presence of
excessive foam, it may exclude the spinning
phase or extend the duration of the program
and increase water consumption.
detergent, that is sprayed onto the laundry
through the jet activating the enzymes at 50°C.
Programmes selection
To clean different types of fabrics and
various levels of dirt, the washing machine
has specific programs to meet every need
of washing (see table of programmes).
WASHING
ALL IN ONE technology
This washing machine is equipped with an
innovative system with an high pressure jet
that sprays a mixture of water and
detergent directly into the load. The special
motor movement used in this machine
manages the drum movement during the
start up of each programme, in conjunction
with the high pressure jet spraying the
detergent mixture into the load, the cycle
includes a set of spin actions that helps the
detergent solution to penetrate into the
fibers, helping dirt removal and ensuring
the best available wash performance. The
ALL IN ONE system is also used during the
water load phases where the high pressure
jet aids the complete removal of detergent
residues trapped in the clothes
All In One 20°C
Thanks to ALL IN ONE technology, this
innovative programme, allows you to wash
fabrics such as cottons, synthetics and
mixed fabrics at 20°C with a performance
which is comparable to a 40°C wash.
The consumption of this program is about
50% of a conventional 40°C. Cottons wash.
IMPORTANT WASH PERFORMANCE
ADVICE:
l New, coloured garments should be washed
separately for at least 5 or 6 washes.
l Certain large dark items such as jeans
and towels should always be washed
separately.
l Never mix NON COLOURFAST fabrics.
All Baby 60°C
You can wash all baby clothes together, at
medium temperature, resulting in hygienic
and perfectly clean items when combined
with heavy duty soap. This is possible
thanks to the ideal pre-dose of water and
22
All In One 59 Min.
This programme allows you to wash mixed
fabrics such as cottons, synthetics and
mixed fabrics in only 59 minutes, using the
full load of the washing machine, at 40°C
(or less) temperature. This programme is
particularly suited to slightly dirty fabrics.
Wool & Silk
This programme allows a delicate washing
cycle, particularly suited to garments specified
as "Machine-Washable" Wool fabrics and
laundry items made from Silk or specified as
"Wash as Silk" on the fabric label.
Rinse
This program performs 3 rinses with an
intermediate spin (which can be reduced or
excluded by using the appropriate button) . It
is used for rinsing any type of fabric, for
example after a wash carried out by hand.
Delicates
This program alternates among moments of
work during breaks and is particularly suitable
for washing delicate fabrics. The wash cycle
and rinses are carried out with a high level of
water to ensure the best performance.
Mixed
The washing and rinsing are optimized in
the rhythms of rotation of the drum and to
the water levels. The gentle spin, ensures a
reduced formation of creases in the fabric.
Cottons
This program is suitable to clean normally
soiled cotton laundry and it is the most efficient
program in terms of combined energy and
water consumptions for washing cotton laundry.
Rapid 30 Min.
A complete washing cycle (wash, rinse and
spin). This programme is particularly suited
to slightly dirty cottons and mixed fabrics.
With this programme it is recommended to
use only 20% of the detergent normally
used to avoid waste.
DRYING
WARNING:
Dispensers used for concentrated
powders and liquid detergents must be
removed from the drum before
commencing
the
tumble
drying
programmes.
The drum changes direction during the
drying cycle to prevent the laundry from
tangling and producing even more drying.
Cool air is used during the last 10/20
minutes of the drying cycle to minimize
creasing.
Low Heat (Acrylics)
Low
temperature
drying
programme
recommended for synthetics and mixed
fibres (always refer to the laundry care label).
High Heat (Cottons)
High temperature drying programme
recommended for cottons and linen items
(always refer to the laundry care label).
Rapid W&D 59 Min.
When you only have a few items to wash
and dry in a hurry, this 59 minute cycle
is the ideal time saver! Suitable for a light
1,5 kg load size (e.g. 4 shirts) or slightly
dirty fabrics, this cycle will wash, rinse, spin
and dry your garments in under an hour.
We recommend that you reduce the
detergent dosage when using this
programme to avoid wastage.
23
EN
Drain & Spin
The program completes the drain and a
maximum spin. It is possible to delete or reduce
the spin with the SPIN SPEED button.
l Only dry pre-spun laundry.
7. DRYING CYCLE
l Drying guidance advice is general, but
practical experience of using the product
will help you to achieve the best drying
results.
l We recommend setting a lower drying
time than indicated, when first using the
appliance in order to establish the degree
of dryness required.
l The washer dryer can perform the
following types of drying:
- Low temperature drying programme
recommended
for
mixed
fabrics
(synthetics/cotton) synthetic fabrics.
l We recommend not drying fabrics that
fray easily, such as rugs or garments with
a deep pile, in order to avoid air duct
clogging.
- High temperature drying programme
recommended for cotton, terry toweling,
linen, hemp fabrics, etc....
l We recommend that you sort the laundry
by the following methods:
- By drying care symbols, which are
displayed on the clothing labels
During the drying phase the drum will
accelerate to a higher speed to
distribute the load and to optimize the
drying performance.
Suitable for tumble drying.
The correct way to dry
Tumble dry at high temperature.
Tumble dry at low temperature only.
The appliance door is fitted with a
protective shield to prevent contact
with the glass door which can reach
high temperatures, during the drying
cycle.
It should not be necessary to remove
the shield from the machine during
the normal course of use.
DO NOT tumble dry.
If the fabric does not have a care label,
you should assume that it is not
suitable for drying.
- By size and thickness
Whenever the wash load is bigger than
the drying capacity, separate the clothes
according to thickness (e.g. towels from
thin underwear).
- By fabric type
Cottons/linen: towels, cotton jersey, bed
and table linen.
Synthetics: blouses, shirts, overalls, etc.
made of polyester or polyamide, as well
as for cotton/synthetic mixes.
24
l Open the door.
l Fill with the laundry, not exceeding the
maximum drying load indicated in the
programme table. For large items (e.g.
sheets) or very absorbent items (e.g.
towels or jeans), it is a good idea to
reduce the load.
l Close the door.
l When the programme is finished the word
button to switch on the appliance.
"End" will appear on the display. After
5 minutes the appliance will go into
standby mode (on certain models, the
display will show two lines).
l Press
the DRYING PROGRAMME
SELECTION button to select the more
suitable drying programme for your
laundry.
l After the programme has finished please
wait for about 2 minutes until the DOOR
LOCKED indicator has gone out before
opening the door.
l Press the DRYING SELECTION button to
select the degree of dryness that you
require, choosing one of 3 automatic
programmes:
l Press for at least 3 seconds the ON/OFF
button to switch off the appliance.
Extra dry programme (suitable for
towels, bathrobes and bulky loads).
l Open the door and remove the laundry.
Iron dry programme (that leaves the
laundry ready for ironing).
l Turn off the tap.
Cupboard dry programme (for
items that will be put away without
ironing).
l To cancel the drying programme, press
CANCELLING THE DRYING PROGRAMME
and hold the DRYING SELECTION
button for about 3 seconds.
l If you wish to select a timed drying
programme,
press
the
DRYING
SELECTION button until the required
time indicator lights up.
WARNING:
After cancelling the drying programme,
the cool down phase will begin and you
must wait for about 10/20 minutes
before opening the door.
l Make sure that the water inlet valve is
open.
l Make sure water drain is correctly
positioned.
WARNING:
Do not dry woollen garments or
articles with special padding (e.g.
quilts, quilted anoraks, etc.) and very
delicate fabrics. If garments are
drip/dry, load less items as to prevent
creasing.
l Press the START/PAUSE button.
l The drying programme indicator will be
on, until the cool down phase begins and
the corresponding indicator is on.
25
EN
l Press for at least 1 second the ON/OFF
SELECTION" button until the required
time indicator lights up.
8. AUTOMATIC
WASHING/DRYING
CYCLE
l Press the START/PAUSE button.
You cannot exceed the maximum
dryable load of laundry indicated in
the programme table, otherwise the
laundry will not be dried satisfactory.
l At the end of the wash phase the display
will show the drying time remaining.
l The washer dryer will then complete the
entire drying programme.
- Washing
l Open the drawer and put in the correct
amount of detergent.
l Press for at least 1 second the ON/OFF
button to switch on the appliance.
for the fabrics to be washed (e.g. very
dirty cotton) and select the required
programme by pressing the related
button.
the
necessary.
wash
temperature
on, until the cool down phase begins and
the corresponding indicator is on.
l When the programme is finished the word
l Refer to the list of washing programmes
l Adjust
l The drying programme indicator will be
if
l Press the option buttons (if required).
"End" will appear on the display. After 5
minutes the appliance will go into
standby mode (on certain models, the
display will show two lines).
l After the programme has finished please
wait for about 2 minutes until the DOOR
LOCKED indicator has gone out before
opening the door.
l Press for at least 3 seconds the ON/OFF
l Check that the tap is turned on and that
the discharge hose is positioned correctly.
button to switch off the appliance.
l Open the door and remove the laundry.
- Drying
l Press the DRYING SELECTION button to
select the degree of dryness that you
require, choosing one of 3 automatic
programmes:
Extra dry programme (suitable for
towels, bathrobes and bulky loads).
l Turn off the tap.
CANCELLING THE DRYING PROGRAMME
l To cancel the drying programme, press
and hold the DRYING SELECTION
button for about 3 seconds.
Iron dry programme (that leaves the
laundry ready for ironing).
Cupboard dry programme (for
items that will be put away without
ironing).
l If you wish to select a timed drying
programme,
press
the
"DRYING
26
WARNING:
After cancelling the drying programme,
the cool down phase will begin and you
must wait for about 10/20 minutes
before opening the door.
If you believe the washing machine is not working correctly, consult the quick guide
provided below with some practical tips on how to fix the most common problems.
Problem
Possible causes and practical solutions
The washing machine
does not work/start
Make sure it is correctly plugged in.
Make sure power is on.
Check whether the required program was correctly selected and to
have correctly started the machine.
Make sure the fuse has not blown and that the wall socket is working,
testing it with another appliance such as a lamp.
The porthole may not be correctly closed: open and close it again.
The washing machine
does not fill with
water
The washing machine
does not drain water
Make sure the water faucet is open.
Water leaked on the
floor near the washing
machine
The washing machine
does not centrifuge
Strong vibrations are
heard during centrifuge
If a specific ERROR
appears of blinks
Make sure the timer is correct set.
Make sure the filter is not clogged.
Make sure the drain hose is not bent.
Make sure there are no foreign objects in the filter.
This may be due to a leak in the gasket between the faucet and supply
tube; in this case, replace it and tighten the tube and faucet.
This could be due to the fact that water has not been completely
drained: wait a few minutes.
Some models include a "no centrifuge" function: make sure it is not on.
An excessive amount of detergent could prevent centrifuge: reduce the
amount at the next wash.
The washing machine may not be fully levelled: if necessary, adjust
the feet as indicated in the specific section.
Make sure transport brackets were removed.
Make sure the load is evenly distributed.
If error no. 0, 1, 5, 7 or 8 appears or blinks, contact the Customer
Service Centre directly.
If error no. 2 appears or blinks, the machine does not load water.
Make sure the water faucet is open.
If error no. 3 appears or blinks, the machine does not correctly drain.
Make sure the drain is free and that the drain hose is not bent.
If error no. 4 appears or blinks, the machine is too full. Close the
water faucet and contact the Customer Service Centre.
If error no. 9 appears or blinks, turn off the washing machine, wait 10
– 15 seconds and restart the program.
27
EN
9. THROUBLESHOOTING AND WARRANTY
The use of ecological detergents without
phosphates may cause the following effects:
- cloudier rinse drain water: This effect is
tied to the suspended zeolites which do
not have negative effects on rinse
efficiency.
If the problem persists or if you suspect a
malfunction,
immediately
contact
an
Authorised Customer Service Centre.
It is always recommended to use original
spare parts, that are available at our
Authorised Customer Service Centres.
- white powder (zeolites) on laundry at
the end of the wash: this is normal, the
powder is not absorbed by fabric and
does not change its colour.
To remove the zeolites, select a rinse
programme. In the future consider using
slightly less detergent.
Warranty
The product is guaranteed under the
terms and conditions stated on the
certificate included with the product. The
warranty certificate must be duly filled in
and stored, so as to be shown to the
Authorised Customer Service Centre in
case of need. Proof of purchase must
be made available at the time of any
warranty related repair.
- foam in the water at last rinse: this
does not necessary indicate poor rinsing.
Consider using less detergent in future
washes.
- abundant foam: This is often due to the
anionic surfactants found in the
detergents which are hard to eliminate
from laundry.
In this case, do not re-rinse to eliminate
these effects: it will not help at all.
We suggest conducting a maintenance
wash using a proprietary cleaner.
The manufacturer declines all
responsibility for any printing errors in
the booklet included with this product.
Moreover, it also reserves the right to
make any changes deemed useful to its
products without changing their essential
characteristics.
28
fkhldsk
fkhldsk
fkhldsk
- WDXT - A -
16.09 - 43015332 - Canon Italia - Business Services Channel
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising