Hoover | DYC 710AV2BX-80N | Hoover DYC 710AV2BX-80N User manual

Hoover DYC 710AV2BX-80N User manual
INSTRUCTION BOOK
DYC 710AV2BX
Condenser Tumble Dryer
English
2
INDEX
Introduction
Delivery Information
Safety Reminders
Use
Installation
The Laundry
Ventilation
Environmental Issues
Gias Service
Installation
Electrical Requirements
Adjusting the Feet
Drain Hose Kit: Fitting Instructions
Preparing the Load
Clothes Preparation
Do Not Tumble Dry
Energy Saving
Sorting the Load
Drying Guide
Controls and Indicators
Selecting the Programme
Door and Filter
Opening the Door
Filter
Filter Care Indicator
Water Container
To Remove the Container
Condenser
To Remove the Condenser
Operation
Delay Start Function
Cancelling and Resetting the Programme
Cleaning and Routine Maintenance
Cleaning the Dryer
Technical Specifications
Troubleshooting
Customer Service
Spares
Gias Service
EN
2
3
3
3
4
5
5
6
7
7
7
7
7
8
9
9
9
9
9
9
10
11
12
12
12
12
12
12
13
13
13
14
14
14
14
14
15
15
15
15
INTRODUCTION
Please read and follow these instructions carefully and operate the machine accordingly. This
booklet provides important guidelines for safe use, installation, maintenance and some useful
advice for best results when using your machine.
Keep all documentation in a safe place for future reference or for any future owners.
Delivery Information
Please check that the following items are
delivered with the appliance:
Check that no damage has occurred to the
machine during transit. If it has, call for service
by GIAS.
• Instruction manual
• Guarantee card
• Energy label
Failure to comply with the above can
compromise the safety of the appliance. You
may be charged for a service call if a problem
with your machine is caused by misuse.
SAFETY REMINDERS
Use
•This appliance can be used by children aged from 8 years and above
and
persons with reduced physical,sensory or mental capabilities or lack of
experience and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe way and understand
the hazards involved.Children shall not play with the appliance. Cleaning
and user maintenance shall not be made by children without
supervision.Children of less than 3 years should be kept away unless
continuously supervised.
• WARNING Misuse of a tumble dryer may create a fire hazard.
•This appliances is intended to be used in household and similar
applications such as:
- Staff kitchen areas in shops , offices and other working environments;
- Farm houses
- By clients in hotels, motels and other residential type environments;
- Bed and breakfast type environments.
A different use of this appliance from household environment or from
typical housekeeping functions,as commercial use by expert or trained
users, is excluded even in the above applications.
EN
3
INTRODUCTION
SAFETY REMINDERS
Use
If the appliance is used in a manner inconsistent with this it may reduce the
life of the appliance and may void the manufacturer’s warranty. Any
damage to the appliance or other damage or loss arising through use that
is not consistent with domestic or household use ( even if located in a
domestic or household environment) shall not be accepted by the
manufacturer to the fullest extent permitted by law.''
•This machine should only be used for its intended purpose as described
in this manual. Ensure that the instructions for installation and use are
fully understood before operating the appliance.
• Do not touch the appliance when hands or feet are damp or wet.
• Do not lean on the door when loading the machine or use the door to lift or
move the machine.
•Do not allow children to play with the machine or its controls.
• WARNING Do not use the product if the fluff filter is not in position or is
damaged; fluff could be ignited.
•WARNING Where the hot surface symbol is located the temperature
rise during operation of the tumble dryer may be in excess of 60 degrees C.
•Remove the plug from the electricity supply. Always remove the plug
before cleaning the appliance.
• Do not continue to use this machine if it appears to be faulty.
• Lint and fluff must not be allowed to collect on the floor around the outside
of the machine.
•The final part of a tumble dryer cycle occurs without heat (cool down
cycle) to ensure that the items are left at a temperature that ensures that
the items will not be damaged.
• Maximum load drying weight 10 kg.
•The tumble dryer is not to be used if industrial chemicals have been used
for cleaning.
• WARNING: Never stop a tumble dryer before the end of the drying cycle
unless all items are quickly removed and spread out so that the heat is
dissipated.
EN
4
INTRODUCTION
SAFETY REMINDERS
Installation
•
Check that the product has no
visible signs of damage before use.
If damaged do not use and please
call GIAS Service.
• Do not use adapters, multiple
connectors and/or extensions.
• Never install the dryer against
curtains and be sure to prevent
items from falling or collecting
behind the dryer.
•The appliance must not be
installed behind a lockable door, a
sliding door or a door with a hinge
on the opposite side to that of the
tumble dryer.
The Laundry
•Do not dry unwashed items in the
tumble dryer.
•WARNING Do not tumble dry
fabrics treated with dry cleaning
fluids.
•WARNING Foam rubber materials
can, under certain circumstances,
when heated become ignited by
spontaneous combustion. Items
such as foam rubber (latex foam),
shower caps, waterproof textiles,
rubber backed articles and clothes
or pillows fitted with foam rubber
pads MUST NOT be dried in the
tumble dryer.
•Always refer to the laundry care
labels for directions on suitability for
drying.
•Clothes
should be spin dried or
thoroughly wrung before they are
put into the tumble dryer. Clothes
that are dripping wet should not be
put into the dryer.
• Lighters and matches must not be
left in pockets and NEVER use
flammable liquids near the
machine.
•Glass fibre curtains should
NEVER be put in this machine. Skin
irritation may occur if other
garments are contaminated with the
glass fibres.
• Items that have been soiled with
substances such as cooking oil,
acetone, alcohol, petrol, kerosene,
spot removers, turpentine, waxes
and wax removers should be
washed in hot water with an extra
amount of detergent before being
dried in the tumble dryer.
•Fabric softeners, or similar
products, should be used as
specified by the fabric softener
instructions.
EN
5
INTRODUCTION
SAFETY REMINDERS
Ventilation
• Adequate ventilation must be
provided in the room where the
tumble dryer is located to prevent
gases from appliances burning other
fuels, including open fires, being
drawn into the room during
operation of the tumble dryer.
• Installing the rear of the appliance
close to a wall or vertical surface.
•There should be a gap of at least 12
mm between the machine and any
obstrubtions.The inlet and outlet
should be kept clear of
obstruction.To ensure adequate
ventilation the space between the
bottom of the machine and the floor
must not be obstructed.
• Check regularly that the air flowing
through the dryer is not restricted.
• Check frequently the fluff filter after
use, and clean, if necessary.
•Prevent items from falling or
collecting behind the dryer as these
may obstruct the air inlet and outlet
• NEVER install the dryer up against
curtains.
• In cases where the dryer is installed
on top of a washing machine, a
suitable stacking kit must be used
according to the follow configuration.
-Stacking kit Mod 35100019: for
minimum washing machine depth
49 cm
-Stacking kit Mod 35900120: for
minimum washing machine depth
51 cm
EN
6
The instructions for installation and
any fixing attachments, are provided
with the staking kit.
Do not install the product in a
low temperature room or in a room
where there is a risk of frost
occurring. At temperature around
freezing point the product may not
be able to operate properly: there
is a risk of damage if the water is
allowed to freeze in the hydraulic
circuit (valves, hoses, pumps). For
a better product performance the
ambient room temperature must
be between +2°C and +35°C.
Please note that operating in cold
condition (between +2 and +15°C)
might simply some water
condensation and water drops on
floor.
INSTALLATION
Environmental Issues
•
All packaging materials used are
environmentally-friendly and recyclable. Please
help dispose of the packaging via
environmentally-friendly means. Your local council
will be able to give you details of current means of
disposal.
• To ensure safety when disposing of an old
tumble dryer disconnect the mains plug from
the socket, cut the mains power cable and
destroy this together with the plug. To prevent
children shutting themselves in the machine
break the door hinges or the door lock.
European Directive 2002/96/EC
This appliance is marked according
to the European directive
2002/96/EC on Waste Electrical and
Electronic Equipment (WEEE).
By ensuring this product is disposed of correctly,
you will help prevent potential negative
consequences for the environment and human
health, which could otherwise be caused by
inappropriate waste handling of this product.
The symbol on the product indicates that this
product may not be treated as household waste.
Instead it shall be handed over to the applicable
collection point for the recycling of electrical and
electronic equipment.
For more detailed information about treatment,
recovery and recycling of this product, please
contact your local city office,your household
waste disposal service or the shop where you
purchased the product. Disposal must be
carried out in accordance with local
environmental regulations for waste disposal.
GIAS Service
Electrical Requirements
Tumble dryers are supplied to operate at a
voltage of 220-240V, 50 Hz single phase. Check
that the supply circuit is rated to at least 10A.
Electricity can be extremely dangerous.
This appliance must be earthed.
The socket outlet and the plug on the
appliance must be of the same type.
Do not use multiple adapters and/or
extension leads.
The plug should be accessible for
disconnection after the appliance has been
installed.
CE Appliance complies with European Directive
2004/108/EC, 2006/95/EC and subsequent
amendments.
You may be charged for a service call if a
problem with your machine is caused by
incorrect installation.
If the mains cord on this appliance is
damaged, it must be replaced by a special cord
which is ONLY obtainable from the spares
service. It must be installed by a competent
person.
Do not plug the machine in and switch it
on at the mains until the installation is
completed.For your safety, this dryer must be
correctly installed. If there is any doubt about
installation, call GIAS Service for advice.
Adjusting the Feet
•
To ensure the continued safe and efficient
operation of this appliance we recommend that
any servicing or repairs are only carried out by an
authorised GIAS service engineer.
If the appliance is not running properly or
breaks down, switch it off and disconnect the
plug from the socket. Consult GIAS Service for
possible repair.
Once the machine is in
place the feet should
be adjusted to ensure
that the machine is
level.
EN
7
DRAIN HOSE : FITTING INSTRUCTIONS
To avoid emptying the water container after
each drying cycle, the water can be
discharged directly to a waste water drain pipe
(the same drainage system as household
sinks). Water Bye-Laws prohibit connection to
a surface water drain. The waste water drain
pipe should be located adjacent to the tumble
dryer.
5. Place the tap
supplied by the kit to
close the remaing
hose.
The kit consists of:1 hose and 1 tap.
WARNING! Switch off and remove the
tumble dryer plug from the electricity supply
before carrying out any work.
6. Once the machine is
in place the feet should
be adjusted to ensure
that the new hose does
not kink when pushing
the tumble dryer into
position.
Fit the Hose as Follows:
1.Tilt the machine
backwards.
2. The waste water
pipe is situated at the
left -hand side of the
machine (see the
picture). A grey hose
connects to the bridge
at the left hand side of
the machine. Using
pliers, remove the pipe
retaining clip from the
bridge.
3. Pull the hose off the
bridge connection.
4. Attach the black
hose from the kit,
(using the connector
and pipe clips
supplied), to the hose
removed from the
bridge connection.
EN
8
7. Connect the new
drain hose to the waste
Water pipe.
8. Connect to the
mains electricity
supply.
PREPARING THE LOAD
Before using the tumble dryer for the first time:
Ÿ
Please read this instruction book thoroughly.
Ÿ
Remove all items packed inside drum.
Ÿ
Wipe the inside of the drum and door with a
damp cloth to remove any dust which may have
settled in transit.
Clothes Preparation
Make sure that the laundry you are going to dry
is suitable for drying in a tumble dryer, as shown
by the care symbols on each item.
Check that all fastenings are closed and that
pockets are empty. Turn the articles inside out.
Place clothes loosely in the drum to make sure
that they don't get tangled.
Do Not Tumble Dry:
Woollens, silk, delicate fabrics, nylon stockings,
delicate embroidery, fabrics with metallic decorations, garments with PVC or leather
trimmings, training shoes, bulky items such as
sleeping bags, etc.
IMPORTANT: Do not dry articles which
have been treated with a dry cleaning fluid or
rubber clothes (danger of fire or explosion).
During the last 15 minutes the load is always
tumbled in cool air.
Energy Saving
Only put into the tumble dryer laundry which
has been thoroughly wrung or spin-dried. The
drier the laundry the shorter the drying time thus
saving electricity.
ALWAYS
•Try to dry the maximum weight of laundry, this
will save time and electricity.
•Check that the filter is clean before every
drying cycle.
NEVER
• Exceed the maximum weight, this will waste
time and electricity.
•Put dripping wet items into the tumble dryer,
this may damage the appliance.
Do not overload the drum, large items
when wet can exceed the maximum admissible
clothes load (for example: sleeping bags,
duvets).
Maximum Drying Weight
•
•
Cottons
Synthetics
Max. 10 kg
Max. 4 kg
Sort the Load as Follows
• By care symbols
These can be found on the collar or inside seam:
Suitable for tumble drying.
..
.
Tumble drying at high temperature.
Tumble drying at low temperature only.
Do not tumble dry.
If the item does not have a care label it must be
assumed that it is not suitable for tumble drying.
● By amount and thickness
Whenever the load is bigger than the dryer
capacity, separate clothes according to
thickness (e.g. towels from thin underwear).
•By type of fabric
Cottons/linen: Towels, cotton jersey, bed and
table linen.
Synthetics: Blouses, shirts, overalls, etc. made
of polyester or polyamid, as well as for cotton/synthetic mixes.
•By drying level
Sort into: iron dry, cupboard dry, etc. For delicate
articles press the Delicates button
to select
low drying temperature.
Drying Guide
The standard cycle HANG DRY (
) is the most
energy efficient and best suited for drying normal wet
cotton laundry.
The table below shows the approximate time and
energy consumption of the main drying programmes.
CYCLE
LOAD
All Towels
Store Dry
Hand Dry
Hang Dry
Iron Dry
FULL
FULL
FULL
HALF
FULL
ENERGY
(kWh)
6,80
6,44
5,70
3,01
4,56
TIME
(Min)
230
210
195
108
159
Power consumption of "left on-mode"
0,75 W
Power consumption of "off-mode"
0,15 W
EN
9
CONTROLS AND INDICATORS
Programme
Selector
Empty Water
Indicator
Filter Care
Indicator
Program
Display
Time Selection Delay Start Acrylic Synthetic
Button
Button
Button
Start/Pause
Button
Anti-Crease
Button
Control Panel and Indicator Lights
Programme Selector – Select the required programme.
Time Selection Button
– Allows the user to change duration of the programme selected by
Programme Selector. It can be used only with the selection of: Mix&Dry, Shirts and Time
Programmes.
Delay Start Button
– Allows the user to delay the start of the drying cycle (see details of
Operation ).
Acrylic and Synthetic Button – When pressed the
default indicator will fade and
will be
illuminated.
Anti- Crease Button
– Allows the user to select a post drying anti-crease cycle.
Start/Pause Button
– Press to commence/ to pause the selected drying programme.
Memo Button – Allows user to record the programme by pressing simultaneously the AntiCrease and the Acrylic Synthetic buttons for 3 seconds, after 2 minutes duration of the chosen
programme/option.
Filter Care indicator
– Lights when the filter needs cleaning.
Empty Water indicator
– Lights when the water container is full.
Program Display – Related indicator lights when a auto programme has been selected.
- Indicator will come on when the eco programme has been selected.
Refresh
– The indicator lights up when the programme starts the cool down stage.
SELECTING THE PROGRAMME
The Hoover Sensor Dry machine gives many options for drying the
laundry to suit all circumstances. The table on the next page lists
the programmes and the function of each programme.
Note:
The sensor may not detect a small load of small articles. For small
loads and separate items or pre-dried fabrics with low moisture
content, use the timed programmes.
If the sensor does not detect the item the dryer will only operate for
10 minutes before going into cooldown.
If the load is too large or too wet to tumble dry the dryer will
automatically go into cooldown after approximately 3 hours.
In these cases we advise to use a time cycles between 30 and
75minutes depending on the load size and dryness required, and
select high or low heat depending upon the fabric type.
EN 10
SELECTING THE PROGRAMME
PROGRAMME
DESCRIPTION
All towels
Store Dry
Hang Dry
Iron Dry
Select the degree of dryness that you require. This range from
for all towels and bathrobes, through
for items that will be put
away without ironing, to the programme that leaves the laundry
suitable for ironing.
Relax 12 Min.
The programme provides a conditioning and anticrease function.
The dryer will heat the load for 9 minutes followed by a 3 minute cool
down period and is especially good for garments which may have
been left for some time prior to ironing, in a linen basket for
example. Garments may also become stiffened when dried outside
on a washing line or inside on radiators.
This programme relaxes the creases in the fabric making ironing
quicker and easier.
Wool Finish
A gentle programme specially created to get woollens softer after
air-drying.This delicate warm air cycle, lasting 12 minutes, can
also be used to get woollens 'refreshed' after being stored in the
wardrobe.
Mix & Dry
This is a special timed program for a maximum load of 4kg (117
min). The default duration is 99 minutes and allows to dry up to 3kg.
With this program you can dry together cotton and synthetic
fabrics.
Shirts
This is a special timed program for shirts of max load of 3kg (78
minutes). For synthetic shirts you have to press the Acrylic
Synthetic button. The default duration is 60 minutes and allows to
dry up to 2kg.
Rapid 40 Min.
The Rapid 40' programme allows a drying cycle to be completed
quickly. This is an ideal programme for having dry, refreshed and
ready-to-wear clothes in less than 40'. This special programme
constantly monitors the temperature in the drum. The maximum load
is 2 kg and the programme is suitable for all types of fabrics where
tumble drying is appropriate.
Time
Time selection includes all the manual time programs: from 30
minutes to 180 minutes. The 20 minutes selection time in only cool
air ventilation (Refresh).
Memo
Memo Program allows to re-perform a program that the user has
saved before, without selecting the correct sequence of program
selector positions and option buttons for that particular program.
EN 11
DOOR and FILTER
Opening the Door
Pull on handle to open
the door.
To restart the dryer,
close the door and
press
.
WARNING! When the tumble dryer is in
use the drum and door may be VERY HOT.
Never stop a tumble dryer before the end of the
drying cycle unless all items are quickly
removed and spread out so that the heat is
dissipated.
Filter
IMPORTANT: To maintain the efficiency of the
dryer check that the fluff filter is clean before
each drying cycle.
1.Pull the
upwards.
filter
2. Open filter as shown.
3. Gently remove lint
using a soft brush or
your fingertips.
4.Snap the filter
together and push
back into place.
Filter Care Indicator
Lights when the
filter needs cleaning.
If the laundry is not
drying check that the
filter is not clogged.
DO NOT USE WATER TO CLEAN THE FILTER.
EN 12
WATER CONTAINER
The water removed from the laundry during the
drying cycle is collected in a container inside the
door of the dryer. When the container is full the
indicator on the control panel will light, and
the container MUST be emptied. However, we
recommend that the container is emptied after
each drying cycle.
NOTE: Very little water will collect during the
first few cycles of a new machine as an internal
reservoir is filled first.
To Remove the Container
1. Gently pull out the
water container
holding the handle.
When it is full the
water container will
weigh about 6 kg.
2 . Ti l t t h e w a t e r
container to empty the
water out through the
spout.
When empty, replace
the water container
back as shown; first
insert the base of the
container into position
as shown then gentle
push the top into
position.
3. Press
Button to
restart the cycle.
NOTE: If you have the
option of drainage near
to the dryer you can
use the discharge kit to
provide a permanent
drainage for the water
collected in the
container of the dryer.
This means that you
don't have to empty the
water container.
1
WARNING! If you open the door mid cycle,
before the cool-down cycle has completed,the
handle may be hot. Please use extreme caution
when attempting to empty the water reservoir
during the cycle.
CONDENSER
Important: Always switch off and remove the
plug from the electricity supply before cleaning
the condenser.
To maintain the efficiency of the dryer regularly
check that the condenser is clean.
To Remove the Condenser
OPERATION
1. Open the door and load the drum with
laundry. Ensure that garments do not hinder
closure of the door.
2. Gently close the door pushing it slowly until
you hear the door 'click' shut.
1.Remove the kickplate.
2. Turn the two locking levers
anti-clockwise and pull out
the condenser.
3.Pull out the condenser
unit.
3. Turn the Programme Selector dial to select
the required drying programme (see
Programme Guide).
4. If drying synthetics, acrylics or delicate items,
press the
button to reduce the heat level.
The indicator will light up when the machine is in
low heat setting. To deselect in the first few
minutes of the programme, press the
button
, after this time reset the machine to change the
setting.
4. Gently remove any dust or
fluff with a cloth, then wash
the unit by holding it under a
running tap turning it so that
water flows between the
plates, to remove any dust or
fluff.
5. Press the
button. The dryer will start
automatically and the indicator above the
button will be continuously lit.
5.Check the gasket position
after cleaning.Fit the gasket
in to the groove if it is
misaligned.
6. If the door is opened during the programme to
check the laundry, it is necessary to press
to
recommence drying after the door has been
closed.
6.Refit the condenser ensuring
it is in the correct way (as
indicated by the arrow) and
pushed firmly into place. Lock
the two levers by turning them
clockwise.Be sure that
condenser unit fixed to the
basement tightly.
7. When the cycle is nearing completion the
machine will enter the cool down phase, the
clothes will be tumbled in cool air allowing the
load to cool down.
7. Refit the kickplate.
8. Following the completion of the cycle the
drum will rotate intermittently to minimize
creasing. This will continue until the machine is
switched OFF or the door is opened.
Do not open the door during the automatic
programs in order to obtain a proper drying.
EN 13
OPERATION
Delay Start Function
The Delay Start Function
allows the user to delay the start of the drying cycle by 1 to 24 hours.
When the function is first selected the display will show a delay of 1 hour, subsequent presses of
the button will increase the delay with 1 hour steps.
To commence the programme press
and the appliance will complete the drying cycle at the
end of this time. The indicator light will flash to indicate that the start delay is in progress.
Cancelling and Resetting the Programme
To cancel a programme press the
button for 3 seconds. In the TIME CONTROL display 0:00
Light will flash to indicate that it has been reset.
CLEANING AND ROUTINE MAINTENANCE
Cleaning the Dryer
•
Clean the filter and empty the water
container after every drying cycle.
•
Regularly clean the condenser.
• After each period of use, wipe the inside of
the drum and leave the door open for a while to
allow circulation of air to dry it.
• Wipe the outside of the machine and the
door with a soft cloth.
• DO NOT use abrasive pads or cleaning
agents.
● To prevent the door sticking or the build up
of fluff clean the inner door and gasket with a
damp cloth after every drying cycle.
WARNING! The Drum, door and load may
be very hot.
EN 14
Technical Specifications
Drum capacity
Maximum load
Height
Width
Depth
Energy Label Band
115 litres
10 kg
85 cm
60 cm
60 cm
B
Information for Test Laboratory
EN 61121 Programme Programme To Use
-DRY COTTON
-IRON DRY COTTON
-EASY-CARE TEXTILE
-HANG DRY
-IRON DRY
-HANG DRY + SYNTHETIC
IMPORTANT Always switch off and
remove the plug from the electricity supply
before cleaning this appliance.
For electrical data refer to the rating label
on the front of the dryer cabinet (with the door
open).
TROUBLESHOOTING
What Might be the Cause of...
Defects you can remedy yourself
Before calling GIAS Service for technical
advice please run through the following
checklist. A charge will be made if the machine
is found to be working or has been installed
incorrectly or used incorrectly.
If the problem persists after completing the
recommended checks, please call GIAS
Service, they may be able to assist you over the
telephone.
Time display to end could change during
drying cycle. The time to end is
continuously checked during the drying
cycle and the time is adjusted to give the
best estimation time. The displayed time
may increase or decrease during the cycle
and this is normal.
Drying time is too long/clothes are not dry
enough…
•Have you selected the correct drying
time/programme?
• Were the clothes too wet? Were the clothes
thoroughly wrung or spindried?
•Does the filter need cleaning?
•Is the dryer overloaded?
•Has the
option been
selected from a
The dryer is noisy…
• Switch off the dryer and contact GIAS Service
for advice.
The
Indicator is on…
• Does the filter need cleaning?
The
Indicator is on…
• Does the water container need emptying?
CUSTOMER SERVICE
Should there still be a problem with your dryer
after completing all the recommended checks,
please call GIAS Service for advice.
They may be able to assist you over the
telephone or arrange for a suitable appointment
for an engineer to call under the terms of your
guarantee. However, a charge may be made if
any of the following applies to your machine:
•
Is found to be in working order.
•
Has not been installed in accordance with the
installation instructions.
•
Has been used incorrectly.
previous cycle?
Spares
The dryer does not operate…
• Is there a working electricity supply to the
dryer? Check using another appliance such as
a table lamp.
• Is the plug properly connected to the mains
supply?
• Is there a power failure?
•Has the fuse blown?
• Is the door fully closed?
• Is the dryer switched on, both at the mains
supply and at the machine?
• Has the drying time or the programme been
selected?
Always use genuine spares, available direct
from GIAS Service.
GIAS Service
For service and repairs call your local GIAS
Service engineer.
The manufacturer declines all responsibility
in the event of any printing mistakes in this
booklet. The manufacturer also reserves the
right to make appropriate modifications to
its products without changing the essential
characteristics.
EN 15
40008694
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising