Hoover | DX HY10A2TKE-80 | Hoover DX HY10A2TKE-80 User manual

Hoover DX HY10A2TKE-80 User manual
Index
Please read and follow these instructions
carefully and operate the machine
accordingly. This booklet provides important
guidelines for safe use, installation,
maintenance and some useful advice for best
results when using your machine.
1. SAFETY REMINDERS
Keep all documentation in a safe place for
future reference or for any future owners.
3. PREPARING THE LOAD
2. DRAIN HOSE KIT: FITTING
INSTRUCTIONS
4. CLEANING AND ROUTINE
MAINTENANCE
Please check that the following items are
delivered with the appliance:
5. WATER CONTAINER
● Instruction manual
● Guarantee card
● Energy label
6. DOOR AND FILTER AND CONDENSER
7. CONTROLS AND INDICATORS
8. SELECTING THE PROGRAMME AND
SET THE FUNCTION
By placing the
mark on this product,
we are confirming compliance to all relevant
European safety, health and environmental
requirements which are applicable in
legislation for this product.
9. TROUBLESHOOTING CUSTOMER
SERVICE
Check that no damage has occurred to
the machine during transit. If it has, call for
service by GIAS. Failure to comply with the
above can compromise the safety of the
appliance. You may be charged for a service
call if a problem with your machine is caused
by misuse.
2
may reduce the life of the
appliance and may void the
manufacturer’s warranty.
Any damage to the appliance
or other damage or loss
arising through use that is not
consistent with domestic or
household use ( even if
located in a domestic or
household environment)
shall not be accepted by the
manufacturer to the fullest
extent permitted by law.
● This appliance can be used by
children aged from 8 years and
above
and persons
with
reduced physical,sensory or
mental capabilities or lack of
experience and knowledge if they
have been given supervision or
instruction concerning use of the
appliance in a safe way and
understand the hazards
involved.Children shall not play
with the appliance. Cleaning and
user maintenance should not be
made by children without
supervision.Children of less than
3 years should be kept away
unless continuously supervised.
● WARNING Misuse of a tumble
dryer may create a fire hazard.
● This appliances is intended to be
used in household and similar
applications such as:
- Staff kitchen areas in shops ,
offices and other working
environments;
- Farm houses;
- By clients in hotels, motels and
other residential type
environments;
- Bed and breakfast type
environments. A different use of
this appliance from house hold
environment or from typical
housekeeping functions,as
commercial use by e x p e r t o r
trained users, is excluded even in
the above applications.
If the appliance is used in a
manner inconsistent with this it
● This machine should only be
used for its intended purpose
as described in this manual.
Ensure that the instructions
for installation and use are
fully understood before
operating the appliance.
● Do not touch the appliance
when hands or feet are damp
or wet.
● Do not lean on the door when
loading the machine or use
the door to lift or move the
machine.
● Do not allow children to play
with the machine or its
controls.
3
EN
1. SAFETY REMINDERS
● WARNING Do not use the
product if the fluff filter is not in
position or is damaged; fluff
could be ignited.
● WARNING Where the hot
surface symbol is
located
the temperature rise during
operation of the tumble dryer
may be in excess of 60 degrees
C.
● Remove the plug from the
electricity supply. Always
remove the plug before cleaning
the appliance.
● Do not continue to use this
machine if it appears to be faulty.
● Lint and fluff must not be
allowed to collect on the floor
around the outside of the
machine.
● The final part of a tumble dryer
cycle occurs without heat (cool
down cycle) to ensure that the
items are left at a temperature
that ensures that the items will
not be damaged.
● The tumble dryer is not to be
used if industrial chemicals have
been used for cleaning.
● WARNING: Never stop a tumble
dryer before the end of the
drying cycle unless all items are
quickly removed and spread out
so that the heat is dissipated.
● Maximum load drying weight:
see energy label.
Installation
● Do not use adapters, multiple
connectors and/or extensions.
● Never install the dryer against
curtains and be sure to prevent
items from falling or collecting
behind the dryer.
● The appliance must not be
installed behind a lockable door,
a sliding door or a door with a
hinge on the opposite side to
that of the tumble dryer.
Important: During transport
ensure that the dryer is in an
upright position, if it's necessary
you can only flip in the side shown;
CAUTION: If the product is in
different side, wait at least 4 hours
before switching on so that the oil
can flow back into the
compressor. Failure to do this
could result in damage to the
compressor.
4
Ventilation
● Adequate ventilation must be
provided in the room where
the tumble dryer is located to
prevent gases from
appliances burning other
fuels, including open fires,
being drawn into the room
during operation of the
tumble dryer.
● Installing the rear of the
appliance close to a wall or
vertical surface.
● There should be a gap of at
least 12 mm between the
machine and any
obstrubtions.The inlet and
outlet should be kept clear of
o b s t r u c t i o n . To e n s u r e
adequate ventilation the
space between the bottom of
the machine and the floor
must not be obstructed.
● Check regularly that the air
flowing through the dryer is not
restricted.
5
EN
petrol, kerosene, spot
removers, turpentine, waxes
and wax removers should be
washed in hot water with an
extra amount of detergent
before being dried in the
tumble dryer.
● Fabric softeners, or similar
products, should be used as
specified by the fabric
softener instructions.
The Laundry
● Do not dry unwashed items in
the tumble dryer.
● WARNING Do not tumble dry
fabrics treated with dry cleaning
fluids.
● WA R N I N G F o a m r u b b e r
materials can, under certain
circumstances, when heated
become ignited by
spontaneous combustion.
Items such as foam rubber
(latex foam), shower caps,
waterproof textiles, rubber
backed articles and clothes or
pillows fitted with foam rubber
pads MUST NOT be dried in the
tumble dryer.
● Always refer to the laundry care
labels for directions on
suitability for drying.
● Clothes should be spin dried or
thoroughly wrung before they
are put into the tumble dryer.
Ɣ 5HPRYH DOO REMHFWV IURP
SRFNHWV VXFK DV OLJKWHUV DQG
PDWFKHV
● Clothes that are dripping wet
should not be put into the dryer.
● Lighters and matches must not
be left in pockets and NEVER
use flammable liquids near the
machine.
● Glass fibre curtains should
NEVER be put in this machine.
Skin irritation may occur if other
garments are contaminated
with the glass fibres.
● Items that have been soiled
with substances such as
cooking oil, acetone, alcohol,
● Check frequently the fluff filter Ɣ 7KHSOXJVKRXOGEHDFFHVVLEOHIRU
after use, and clean, if necessary.
GLVFRQQHFWLRQ DIWHU WKH DSSOLDQFH
● Prevent items from falling or KDVEHHQLQVWDOOHG
collecting behind the dryer as
7KH DSSOLDQFH
these may obstruct the air inlet :$51,1*
PXVWQRWEHVXSSOLHGWKURXJK
and outlet.
● NEVER install the dryer up DQ H[WHUQDO VZLWFKLQJ GHYLFH
VXFKDVDWLPHURUFRQQHFWHG
against curtains.
WR D FLUFXLW WKDW LVUHJXODUO\
● In cases where the dryer is VZLWFKHGRQDQGRIIE\DXWLOLW\
installed on top of a washing
machine, a suitable stacking kit
,IWKHVXSSO\FRUGLVGDPDJHG
must be used according to the
configuration of your appliance. LW PXVW EH UHSODFHG E\ WKH
PDQXIDFWXUHULWVVHUYLFHDJHQWRU
- Stacking kit "standard size": VLPLODUO\ TXDOLILHG SHUVRQV LQ
for washing machine with RUGHUWRDYRLGDKD]DUG
minimum depth of 44 cm;
- Stacking kit "slim size":
Do not install the product in a
for washing machine with low temperature room or in a
minimum depth of 40 cm;
room where there is a risk of frost
occurring. At temperature around
The stacking kit shall be
freezing point the product may
obtainable from our spare
not be able to operate properly:
service.
there is a risk of damage if the
The instructions for installation
water is allowed to freeze in the
and any fixing attachments, are
hydraulic circuit (valves, hoses,
provided with the stacking kit.
pumps). For a better product
performance the ambient room
temperature must be between
5-35°C. Please note that
operating in cold condition
(between +2 and +5°C) might
simply some water condensation
and water drops on floor.
Air Outlets in the Base
6
Environmental Issues
Tumble dryers are supplied to operate at a
voltage of 220-240V, 50 Hz single phase.
Check that the supply circuit is rated to at least
13 A.
Electricity can be extremely dangerous.
This appliance must be earthed.
The socket outlet and the plug on the
appliance must be of the same type.
Do not use multiple adapters and/or
extension leads.
Contains fluorinated
greenhouse gases.
Hermetically sealed.
European Directive 2012/19/EU
This appliance is marked according
to the European directive 2012/19/EU
on Waste Electrical and Electronic
Equipment (WEEE).
GWP1430
You may be charged for a service
call if a problem with your machine is
caused by incorrect installation.
WEEE contains both polluting substances
(which can cause negative consequences for
the environment) and basic components (which
can be re-used). It is important to have WEEE
subjected to specific treatments, in order to
remove and dispose properly all pollutants, and
recover and recycle all materials.
Individuals can play an important role in
ensuring that WEEE does not become an
environmental issue; it is essential to follow
some basic rules:
Do not plug the machine in and
switch it on at the mains until the
installation is completed.For your safety,
this dryer must be correctly installed. If
there is any doubt about installation, call
GIAS Service for advice.
Adjusting the Feet
- WEEE should not be treated as household
waste.
- WEEE should be handed over to the relevant
collection points managed by the municipality or
by registered companies. In many countries, for
large WEEE, home collection could be present.
Once the machine is
in place the feet
should be adjusted to
ensure that the
machine is level.
In many countries, when you buy a new
appliance, the old one may be returned to the
retailer who has to collect it free of charge on a
one-to-one basis, as long as the equipment is of
equivalent type and has the same functions as
the supplied equipment.
GIAS Service
● To ensure the continued safe and efficient
operation of this appliance we recommend
that any servicing or repairs are only carried
out by an authorised GIAS service engineer.
7
EN
Electrical Requirements
● All packaging materials used are
environmentally-friendly and recyclable.
Please help dispose of the packaging via
environmentally-friendly means. Your
local council will be able to give you details
of current means of disposal.
● To ensure safety when disposing of an old
tumble dryer disconnect the mains plug
from the socket, cut the mains power cable
and destroy this together with the plug. To
prevent children shutting themselves in
the machine break the door hinges or the
door lock.
2. DRAIN HOSE : FITTING
4. Attach the black
hose from the kit,
(using the connector
and pipe clips
supplied), to the hose
removed from the
bridge connection.
INSTRUCTIONS
To avoid emptying the water container after
each drying cycle, the water can be discharged
directly to a waste water drain pipe (the same
drainage system as household sinks). Water
Bye-Laws prohibit connection to a surface
water drain. The waste water drain pipe should
be located adjacent to the tumble dryer.
5. Connect the new
drain hose to the waste
Water pipe.
The kit consists of:1 hose and 1 tap.
WARNING!
Switch off and remove the
tumble dryer plug from the electricity supply
before carrying out any work.
Fit the Hose as Follows:
1. Flip the machine
slowly to the right
side.
6. Once the machine is
in place, check the
bottom to ensure that
the new hose does not
kink when pushing the
tumble dryer into
position.
1
4
5
6
Connect to the mains
electricity supply.
2. The waste water
pipe is situated at the
right-hand side of the
machine (see the
picture). A grey hose
connects to the bridge
at the left hand side of
the machine. Using
pliers, remove the
pipe retaining clip
from the bridge.
2
CAUTION: If the product is in different side,
wait at least 4 hours before switching on so
that the oil can flow back into the
compressor. Failure to do this could result
in damage to the compressor.
3
3. Pull the hose off the
bridge connection.
8
If the item does not have a care label it must
be assumed that it is not suitable for tumble
drying.
● By amount and thickness
Whenever the load is bigger than the dryer
capacity, separate clothes according to
thickness (e.g. towels from thin underwear).
● By type of fabric
Cottons/linen: Towels, cotton jersey, bed
and table linen.
Synthetics: Blouses, shirts, overalls, etc.
made of polyester or polyamid, as well as
for cotton/synthetic mixes.
Before using the tumble dryer for the first time:
● Please read this instruction book thoroughly.
● Remove all items packed inside drum.
● Wipe the inside of the drum and door with a
damp cloth to remove any dust which may have
settled in transit.
Clothes Preparation
Make sure that the laundry you are going to
dry is suitable for drying in a tumble dryer, as
shown by the care symbols on each item.
Check that all fastenings are closed and that
pockets are empty. Turn the articles inside out.
Place clothes loosely in the drum to make sure
that they don't get tangled.
Do not overload the drum, large items
when wet exceed the maximum
admissible clothes load (for example:
sleeping bags, duvets).
Do Not Tumble Dry:
Silk, nylon stockings, delicate embroidery,
fabrics with metallic decorations, garments
with PVC or leather trimmings.
4.
IMPORTANT: Do not dry articles which
have been treated with a dry cleaning fluid or
rubber clothes (danger of fire or explosion).
Cleaning the Dryer
● Clean the filter and empty the water
container after every drying cycle.
● Regularly clean the condenser.
● After each period of use, wipe the inside
of the drum and leave the door open for a
while to allow circulation of air to dry it.
● Wipe the outside of the machine and the
door with a soft cloth.
● DO NOT use abrasive pads or cleaning
agents.
● To prevent the door sticking or the build
up of fluff clean the inner door and gasket
with a damp cloth after every drying cycle.
During the last 15 minutes the load is always
tumbled in cool air.
Energy Saving
Only put into the tumble dryer laundry which has
been thoroughly wrung or spin-dried. The drier
the laundry the shorter the drying time thus
saving electricity.
ALWAYS
● Check that the filter is clean before every
drying cycle.
NEVER
● Put dripping wet items into the tumble dryer,
this may damage the appliance.
WARNING! The Drum, door and load
may be very hot.
Sort the Load as Follows
IMPORTANT Always switch off and
remove the plug from the electricity supply
before cleaning this appliance.
● By care symbols
These can be found on the collar or inside seam:
Suitable for tumble drying.
..
Tumble drying at high temperature.
.
Tumble drying at low temperature only.
CLEANING AND ROUTINE
MAINTENANCE
For electrical data refer to the rating
label on the front of the dryer cabinet (with
the door open).
Do not tumble dry.
9
EN
3. PREPARING THE LOAD
5. WATER CONTAINER
OPERATION
The water removed from the laundry during the
drying cycle is collected in a container inside
the door of the dryer. When the container is full
the
indicator on the control panel will
light, and the container MUST be emptied.
However, we recommend that the container is
emptied after each drying cycle.
NOTE: Very little water will collect during the
first few cycles of a new machine as an internal
reservoir is filled first.
To Remove the Container
2. Gently close the door pushing it slowly
until you hear the door 'click' shut.
3. Turn the Programme Selector dial to
select the required drying programme (see
Programme Guide).
4. Press the
button. The dryer will start
automatically and the indicator above the
button will be continuously lit.
1. Gently pull out the
water container holding
the handle. (A)
When it is full the
water container will
weigh about 6 kg.
5. If the door is opened during the
programme to check the laundry, it is
necessary to press
to recommence
drying after the door has been closed.
2. T i l t t h e w a t e r
container to empty the
water out through the
spout. (B)
6. When the cycle is nearing completion
the machine will enter the cool down
phase, the clothes will be tumbled in cool
air allowing the load to cool down.
A
When empty, replace
the water container
back as shown; (C) first
insert the base of the
container into position
as shown (1) then
gentle push the top into
position (2).
7. Following the completion of the cycle the
drum will rotate intermittently to minimize
creasing. This will continue until the
machine is switched OFF or the door is
opened.
Do not open the door during the automatic
programs in order to obtain a proper drying.
B
3. Press
Button to
restart the cycle.
NOTE: If you have the
option of drainage near
to the dryer you can use
the discharge kit to
provide a permanent
drainage for the water
collected in the
container of the dryer.
This means that you
don't have to empty the
water container.
1. Open the door and load the drum with
laundry. Ensure that garments do not
hinder closure of the door.
1
C
10
6. DOOR AND FILTER
WARNING! When the
tumble dryer
is in use the drum and door may be VERY HOT.
Filter
IMPORTANT: To maintain the efficiency of
the dryer check that the fluff filter is clean
before each drying cycle.
1.P u l l t h e
upwards.
EN
To Clean the Condenser Filter
Pull on handle to open the door.
To restart the dryer, close the door and press
Start / Pause button.
1. R e m o v e
kickplate.
the
2. Turn the two locking 1
levers anti-clockwise
and pull out the front
cover.
3. Gently remove the
filter frame and clean
any dust or fluff with a 2
cloth from the filter. Do
not use water to clean
the filter.
filter
2.Open filter as shown.
1
4. Remove the sponge
gently from its place
and then wash the
sponge by holding it 3
under a running tap
turning it so to remove
any dust or fluff.
3.Gently remove lint
using a soft brush or
your fingertips.
4.S n a p t h e f i l t e r
together and push
back into place.
2
Filter Care Indicator
Lights when the filter needs cleaning.
If the laundry is not drying check that the filter
is not clogged.
IF YOU CLEAN FILTER UNDER
WATER, REMEMBER TO DRY IT.
5. Refit the front cover
ensuring it is in the
correct way (as
indicated by the arrow)
and pushed firmly into 4
place. Lock the two
levers by turning them
clockwise.
6. Refit the kickplate.
5
WARNING! If you open the door mid
cycle, before the cool-down cycle has
completed,the handle may be hot. Please use
extreme caution when attempting to empty
the water reservoir during the cycle.
Clean the filters before every cycle
11
7. CONTROLS AND
4.Drying Selection Button
It allows to set the desired dryness level editable
option up to 5 minutes after the starting of the
cycle:
- Ready to Iron : It leaves the garments
slightly wet to facilitate ironing.
- Dry Hanger : To get garment ready to be
hang
- Dry wardrobe : For laundry that can be
directly stored
-Extra-dry : To get completely dry garments,
ideal for full load.
This appliances is equipped with Drying Manager
Function. On automatic cycles, each level of
intermediate drying, prior to the reaching the
selected one, is indicated by flashing the light
indicator corresponding to the degree of drying
reached. In case of incompatibility, all LEDs flash
quickly for 3 times.
INDICATORS
A
E
D
B
C
7
6
4
5
3
2
1
8
A-Programme Selector - Rotating the knob in
both directions it's possible to select the desired
drying program. To cancel the selections or
switch off the dryer rotate the knob on OFF.
B- Display Digit - The display shows the
remaining time for drying, the postponed time in
case of delayed start selection and other
notifications setting.
C-Buttons 1.Start/Pause Button
To start the selected program and/or suspend it.
2.Delay Start Button
It allows to delay the start of the program from 1
to 24 hours in 1-hour intervals. The delay
selected is shown on the display.
After pressing the START button the time
showed decrease hour after hour.
Opening of the porthole with delayed start set,
after re-closing the porthole, press start again to
resume the counting.
3.Time cycle selection
It's possible transform a cycle from automatic to
programmed, up to 3 minutes after the start of
the cycle.
The progressive pressure increases the time in
10-minute intervals. After this selection to reset
the automatic drying functioning is necessary to
switch off the dryer. In case of incompatibility, all
LEDs flash quickly for 3 times.
12
5.Rapids Button
It's possible switch an automatic program to
RAPID program, up to 3 minutes after the start of
the cycle. The progressive pressure increases the
time (30-45-59 minutes).
After this selection to reset the automatic drying
functioning is necessary to switch off the dryer. In
case of incompatibility, all LEDs flash quickly for 3
times.
6.Best Ironing
This option allows to reduce folds and tangles,
thanks to alternating movements of the drum
during and after drying and automatically, setting
the ironi drying level (the drying level setting can
be modified after the option selection).
The option can be set up to five minutes after the
start of the cycle and is activated only on
automatic cycles.
7.Memory
This option allows you to store the options set on
a cycle.
STORAGE When the cycle is running push the
button "memory" for three seconds. The control
light "memory" flashes for three times and stores
the set options connected to the cycle selected in
the flange.
Recall: After the selection of the cycle Push the
button "memory" for recall the stored options.
(not the cycle).
8. Keylock
This function allows to block unwanted changes
of the set options on the bezel , during drying
phase. Activation/Inactivation: push 4 and 5
buttons simultaneously for two seconds . The
sign "LOC" appears on the display. Unlocking the
option, on the display appears the sign "Unl", only
once. In case of opening of 'porthole' with
activated key lock, the cycle stops but the lock is
kept: to restart the cycle, you must remove the
lock and restore Start. When the dryer is off, the
option is automatically inactivated.
Key lock can be modified at any time of the cycle.
D- Led
Water tank
- It lights up when it's necessary
to empty the condensate water tank.
Filter cleaning
- It lights up when the
cleaning of the filters is requested (the door and
the lower filter.)
Cooling
- It lights up when the cycle is in the
final cooling phase.
EONE TOUCH area - pressing the
START/PAUSE button allows to a previously
downloaded cycle to start whilst the Touch
position is selected on the programme knob
(for downloading cycles from the App see the
relevant section of this user manual).
The wool drying cycle of this
machine has been
approved by The Woolmark
Company for the drying of
machine washable wool
products provided that the
products are washed and
dried according to the instructions on the
garment label and those issues by the
manufacturer of this machine M1530.
In UK, Eire, Hong Kong and India the Woolmark
trade mark is a Certification trade mark.
Max.capacity declared
Synthetics or Delicates
Max.4 Kg
The standard cycle COTTON DRY (
) is the
most energy efficient and best suited for drying
normal wet cotton laundry.
The table in last page shows the approximate
time and energy consumption of the main
drying programmes.
Power consumpt on of off-mode
0,40 W
Power consumpt on of on-mode
0,75 W
Technical Specifications
Drum capac ty
Max mum load
He ght
W dth
Depth
Energy class
125
See energy label
85 cm
60 cm
60 cm
See energy label
Information for Test Laboratory
EN 61121 Programme To Use
- STANDARD DRY COTTON
- IRON DRY COTTON
- EASY-CARE TEXTILE
WHITES
SYNTHETICS
Clean the filters before every cycle
The real duration of drying cycle
depends by the starting humidity level of
the laundry due to spin speed, type and
amount of load, cleanliness of filters and
ambient temperature.
ONLY FOR 10 KG CAPACITY
TUMBLE DRYER : CONNECT THE
DRAIN HOSE FOR RECOVERING
CONDENSER WATER ACCORDING
TO INSTRUCTION AT CHAPTER 2
Maximum Drying Weight
Cottons
Drying Guide
EN
Automatic Anti crease
This option automatically activates an anticreases movement of the drum, pre cycle in
case of activation of the delay and at the end
of drying cycle for 6 hours. It is activated
every 10 minutes. To stop the movements
set the knob to OFF.
Useful when it's not possible to remove
immediately the laundry.
13
8.
SELECTING THE PROGRAMME AND SET THE FUNCTION
CAPACITY
PROGRAM
ecoSpeed Mixed
(kg)
DRYING
TIME
(min)
A new innovative cycle to dry different kinds of fabrics in the same
time. The dryer provides an alert when the lightweight fabrics are dry
and ready to are taking out (on the display the text AIO blinks for 3
minutes and an acustic sound is emitted) . After this step it's
necessary to press start
again to complete the dryng for the
leftovers heavier linens.
6
*
This special cycles allows to shorten around 1/4 the drying time
for synthetics and mixed loads, still assuring a high energy
efficiency in A class
4
*
Full
*
4
*
PROGRAM DESCRIPTION
This special cycles allows to shorten of 1/3 the drying time for
Cotton loads, still assuring a high energy efficiency in A class
A delicate and specific cycle to dry dark or coloured cotton or
Darks & Coloured synthetics garments.
ecoSpeed Cotton
Whites
The right cycle to dry cottons, sponges and towels.
Full
*
Program Eco normative (hang dry) drying. The most
efficient program in energy consumption. Suitable for
cottons and linens.
Full
*
Shirts
This specifics cycle has been conceived to dry shirts minimizing
tangles and folds thanks specific movements of the drum. It's
recommended to take out the linens immediately after drying cycle.
2.5
*
Jeans
Dedicated to dry uniformly fabrics like jeans or denim. It's
recommended flip over the garments before drying.
4
*
Synthetics
To dry delicate and synthetic fabrics that need an accurate
and specific treatment.
4
*
Bed Quilt
Perfect cycle to dry uniformly duvets and quilts, revitalizing
the smoothness of the feathers.
4
*
Wool
Woolen clothes: the program can be used to dry up to 1 kg of
laundry (around 3 jumpers). It is recommended to reverse all
clothes before drying. Timing can change due to dimensions
and thickness of load and to spinning chosen during
washing. At the end of the cycle, clothes are ready to be
worn, but if they are heavier, edges can be a bit wet: it is
suggested to dry them naturally. It is recommended to
unload clothes at the very end of the cycle. Attention: felting
process of wool is irreversible; please dry exclusively clothes
with symbol (symbol "ok tumble"); this program is not
indicated for acrylic clothes.
1
70’
Cotton
Antiallergy
One specifics cycle that dry and in the same time helps to
reduce the main allergens as dust mites, pet hair, pollens
and residual of powder detergents.
4
Max 220’
xxL Load
Specific cycle dedicated to dry large linens e.g. curtains
sheets and tableclothes. Thanks to a specifics movement of
the drum the linens will be dry minimizing tangles and folds.
6
*
Anti Odours
The perfect cycle to remove the smells from the linens
smoothing creases.
2.5
20’
Customizable setting that interacts with the App on your android smartphone and to
download the cycles (see the dedicated section). The factory sets the default programme
Auto-Hygiene, which will sanitize the machine.
* The real duration of drying cycle depends by the starting humidity level of the laundry due to spin speed, type
and amount of load, cleanliness of filters and ambient temperature.
14
● Clever Care – Clever Check-up and
troubleshooting guide.
ONE TOUCH
This appliance is equipped with One Touch
technology that allows you to interact, via the
App, with smartphones based on Android
operating system and equipped with NFC
(Near Field Communication) function.
● Reports – Drying statistics and tips for a
more efficient use of your machine.
● Download on your smartphone the Hoover
Wizard App.
Get all the details of the One Touch
functions, browsing the App in DEMO
mode or go to:
www.hooveronetouch.com
HOW TO USE ONE TOUCH
The Hoover Wizard App is available
for devices running both Android
and iOS, both for tablets and for
smartphones. However, you can
interact with the machine and take
advantage of the potential offered by
One Touch only with Android
smartphones equipped with NFC
technology, according to following
functional scheme:
Android smartphone
with NFC technology
FIRST TIME - Machine registration
Enter the "Settings" menu of your
Android smartphone and activate the
NFC function inside the "Wireless &
Networks" menu.
Depending on the smartphone model
and its Android OS version, the
process of the NFC activation may be
different. Refer to the smartphone
manual for more details.
Interaction with the
machine + contents
Android smartphone
without NFC technology Contents only
Android Tablet
Apple iPhone
Apple iPad
● Turn the knob to the One Touch
position to enable the sensor on the
dashboard.
Contents only
Contents only
Contents only
● Open the App, create the user profile
and register the appliance following the
instructions on the phone display or the
"Quick Guide" attached on the machine.
FUNCTIONS
The main functions available using the App
are:
More information, F.A.Q. and the video
for an easy registration are available
on:
www.hooveronetouch.com/how-to
● Voice Coach – A guide to help you choose
the ideal cycle with only three voice inputs
(clothes/fabrics, colour, drying level).
● Programmes – To download and launch
new drying programmes.
15
● Every time you want to manage the
machine through the App, first you have to
enable the One Touch mode by turning the
knob to the One Touch indicator.
● Make sure you have unlocked your phone
(from stand-by mode) and you have
activated the NFC function; then, follow the
steps mentioned earlier.
● If you want to start a dry cycle, load
the laundry and close the door.
● Select the desired function in the App (e.g.:
starting a programme, the Clever Checkup cycle, update statistics, etc…).
● Follow the instructions on the phone
display, KEEPING IT ON the One Touch
logo on the machine dashboard, when
requested to do so by the App.
If you do not know the position of your NFC
antenna, slightly move the smartphone in a
circular motion over the One Touch logo
until the App confirms the connection. In
order for the data transfer to be successful,
it is essential TO KEEP THE SMARTPHONE
ON
THE
DASHBOARD
DURING
THE F E W S E C O N D S O F T H E
PROCEDURE; a message on the device will
inform about the correct outcome of the
operation and advise you when it is
possible to move the smartphone away.
Thick cases or metallic stickers on your
smartphone could affect or prevent the
transmission of data between machine and
telephone. If necessary, remove them.
The replacement of some components of
the smartphone (e.g. back cover, battery,
etc...) with non-original ones, could result
in the NFC antenna removal, preventing
the full use of the App.
The management and the control of the
machine via App is only possible "by
proximity": it is therefore not possible to
perform remote operations (e.g.: from
another room; outside of the house).
WIRELESS PARAMETERS
Parameter
NOTES:
Specifications
Wireless Standard
ISO/IEC 14443 Type A and NFC Forum Type 4
Frequency band
13,553-13,567 MHz (centre frequency 13,560 MHz)
Magnetic field limit
< 42dBμA/m (at 10 meters)
With this the Candy Hoover Group Srl,
declares that this appliance marked
with
complies with the essential
requirements of the Directive
2014/53/EU.
To receive a copy of the declaration of
conformity, please contact the
manufacturer at:
www.candy-group.com
Place your smartphone so that the NFC
antenna on its back matches the position
of the One Touch logo on the appliance (as
illustrated below).
16
EN
NEXT TIME – Regular usage
9. TROUBLESHOOTING
FOR ONE TOUCH MODELS
The Hoover Wizard app has a Clever Check-up function that allows you to confirm the
functionality and status of the product at any time. To use the Hoover Wizard app you will need an
Android smartphone with NFC technology.
More info can be found on the App.
If the display of the machine is showing an error (by a code or blinking LEDs), you should turn on the App
on your Android smartphone, with NFC on, selecting "Read the error" on the "Help on line" menu. Place
your smartphone against the One Touch logo on the control panel. You should now be able to read the
fault directory to solve the issue.
What Might be the Cause of...
Defects you can remedy yourself
Before calling service for technical advice please
run through the following checklist. A charge will
be made if the machine is found to be working or
has been installed incorrectly or used incorrectly.
If the problem persists after completing the
recommended checks, please call Service, they
may be able to assist you over the telephone.
Time display to end could change during
drying cycle. The time to end is continuously
checked during the drying cycle and the time
is adjusted to give the best estimation time.
The displayed time may increase or decrease
during the cycle and this is normal.
Drying time is too long/clothes are not dry
enough…
● Have you selected the correct drying
time/programme?
● Were the clothes too wet? Were the clothes
thoroughly wrung or spindried?
● Does the filter need cleaning?
● Is the dryer overloaded?
The dryer does not operate…
● Is there a working electricity supply to the
dryer? Check using another appliance such as a
table lamp.
● Is the plug properly connected to the mains
supply?
● Is there a power failure?
● Has the fuse blown?
● Is the door fully closed?
● Is the dryer switched on, both at the mains
supply and at the machine?
● Has the drying time or the programme been
selected?
● Has the machine been switched on again after
opening the door?
17
The dryer is noisy…
● Switch off the dryer and contact GIAS
Service for advice.
The
Indicator is on…
● Does the filter need cleaning?
The
Indicator is on…
● Does the water container need
emptying?
CUSTOMER SERVICE
Should there still be a problem with your
dryer after completing all the
recommended checks, please call
service for advice.
They may be able to assist you over the
telephone or arrange for a suitable
appointment for an engineer to call under
the terms of your guarantee. However, a
charge may be made if any of the
following applies to your machine:
● Is found to be in working order.
● Has not been installed in accordance
with the installation instructions.
● Has been used incorrectly.
Spares
Always use genuine spares, available
direct from service.
Service
For service and repairs call your local
service engineer.
The manufacturer declines all
responsibility in the event of any
printing mistakes in this booklet. The
manufacturer also reserves the right
to make appropriate modifications to
its products without changing the
essential characteristics.
Capacity
Energy
Capac ty (kg)
Class
Energy kWh
Whites
T me
M n.
Energy
kWh
Whites
T me
M n.
Energy kWh
Cotton
T me
M n.
Energy
kWh
Cotton ½
T me
M n.
Energy
kWh
Whites
T me
M n.
9
A+
3,23
330
2,82
300
2,56
260
1,31
149
2,05
210
10
A+
3,80
350
3,35
335
3,05
315
1,70
159
2,44
230
Time
9
A++
2,75
330
2,40
300
2,18
260
1,15
149
1,74
210
10
A++
3,10
379
2,73
336
2,48
305
1,18
152
1,98
244
40012827
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising