ROSIERES | PCGTS76/1INA | ROSIERES PCGTS76/1INA User manual

ROSIERES PCGTS76/1INA User manual
EN HOBS 70 cm
USER INSTRUCTIONS
TECHNICAL CHARACTERISTICS
INSTALLATION
Cooking hobs 70x50
Burners
Reference type
Supply Voltage
(V/Hz)
Installed electric power
(W)
Medium burner
Large burner
Small burner
Double ring burner
Maxi burner
Fish burner
Power of gas installed:
- Natural gas 1,0 kPa (MJ/H)**
- LPG gas 2,75 kPa (MJ/H)
Electric ignition*
Gas safety device
Product size
mm.
Degree protection
Class
5 gas
–
P751
230/50
–
1
2
1
1
–
–
5 gas
–
P751
230/50
–
1
2
1
–
1
–
5 gas
–
P751
230/50
–
1
2
1
–
–
1
5 gas
–
P752
230/50
–
1
2
1
1
–
–
5 gas
–
P752
230/50
–
1
2
1
–
1
–
5 gas
–
P752
230/50
–
1
2
1
–
–
1
40,5
37,4
yes
–
695x510
–
3
40,5
37,4
yes
–
695x510
–
3
40,5
37,4
yes
–
695x510
–
3
40,5
37,4
yes
yes
695x510
–
3
40,5
37,4
yes
yes
695x510
–
3
40,5
37,4
yes
yes
695x510
–
3
The Purchaser is responsible for the installation of the hob. The Manufacturer does not
accept any responsibility for any damage or loss resulting from incorrect installation,
and as such this will not covered by the Manufacturer’s Guarantee.
The hob may be installed in any worktop which is heat resistant to a temperature of
100° C, and has a thickness of 25 - 40 mm. The dimensions of the insert to be cut out
of the worktop are in shown in Fig. 1.
If the Hob is fitted next to a cabinet on either side,
150 mm
min.
the distance between the Hob and the cabinet
must be at least 150 mm (see Fig. 2); while the
distance between the hob and the rear wall must
be at least 55 mm.
30 mm
If below the hob there is an accessible space,
there must be a partition panel in insulating material (wood or similar) providing a space of at least
10 mm
10 mm below the Hob (see Fig. 2).
Partition panel
The Hob unit is fitted by attaching the Fixing
Fig. 2
Clamps supplied, using the holes at the base of
the unit.
VERY IMPORTANT - APPLYING THE SEALANT
Fig. 1
* Some models only
** Manufacturer setting
Important - The diagram below shows how the sealant should be applied.
This appliance has been designed for non-professional, i.e. domestic, use.
Appropriate checks and tests have ensured that, even in the most extreme conditions,
the temperatures reached are within acceptable limits. The Hob is thermally insulated (in line with Regulation EN) and may be installed: next to panels higher than
the worktop, for type «Y», or next to panels not higher than the worktop for type
«X». See technical characteristics table «Degree of protection».
1
2
and 0,75 mm2 for others products. Also, the maximum external diameter of the cable
should not be greater than 7 mm.
Instructions for the installer
Suitable location
A gas-powered cooking appliance produces heat
and himidity in the area in which it is installed. For
this reason you should ensure good ventilation either
by keeping all natural air passages open or by installing an extractor hood with an ehaust flue (Fig.
3-4). Intensive and prolonged use of the appliance
may require extra ventilation, such the opening of
a window or an increase in speed of the electric fan,
if you have one.
If your appliance is not fitted with a thermocouple
(safety device) the ventilation hole shown in Fig. 3
should be at least 200 cm2.
MAINS
SUPPLY
L
BROWN WIRE
EARTH
GREEN/YELLOW WIRE
NEUTRAL N
BLUE WIRE
POWER
CABLE
Declaration of compliance. The parts of this equipment which are designed to come
into contact with foodstuffs, comply with EEC directive 89/109.
Fig. 3
Appliance complying with European directives 89/336/EEC, 90/396/EEC,
73/23/EEC and subsequent modifications.
Gas connection
If a hood cannot be installed, an electric fan
should be fitted to an outside wall or window as
long there are air vents in the area.
The electric fan should be able to carry out a complete change of air in the kitchen 3-5 times every
hour.
The installer should follow the relavant national
standards.
Fig. 4
Electrical connection
Check the data on the rating plate, located on the outside of the unit, to ensure that the
supply and input voltage are suitable.
Before connection, check the earthing system.
By Law, this appliance must be earthed. If this regulation is not complied with, the
Manufacturer will not be responsible for any damage caused to persons or property.
If a plug is not already attached, fit a plug appropriate to the load indicated on the rating
plate. The earth wire is coloured yellow/green.
Where the Hob is connected direct to the electricity supply, a circuit breaker must be
fitted with at least a 3 mm contact spacing when in the open position.
It if is necessary to replace the connecting cable, the earth wire (yellow/green) must,
by law, be approximately 10 mm longer than the live and neutral wires. Rubber insulated cable type H05RR-F must be used.
The cables should be 1,5 mm2 section for products with electrically heated elements,
3
LIVE
The rating plate on the hob shows the type of gas with which it is designed to be used.
It is possible to use other types of gas after carrying out some simple modifications.
a) Connection to the gas supply
— connection to the mains gas supply or gas cylinder should be carried out according
to the relevant national standards, after having checked that it is regulated for the
type of gas with which it will be supplied. If it is not correctly regulated follow the
instructions in the paragraph entitlet «Adaption for different types of gas». For liquid
gas (cylinder gas) use pressure regulators which comply with the relevant national
standards.
N.B.: for safe operation, economic use of energy and to ensure greater durability
of the appliance, make sure that the supply pressure conforms with the values shown
in the table on page 6 .
— Connection to a rigid pipe (see instruction on page 10)
Connection to the gas supply should be done without putting any kind of stress on
the appliance.
— Connection to a flexible steel pipe (see instructions on page 10)
The junction of the gas pipe with the appliance is a 1/2” gas tapered thread connection. Use only pipes, washers and sealing washers which comply with the relevant
national standards.
The fitting of these pipes should be done to that their
maximum length, when fully extended, should not
exceed 2000 mm.
N.B.: carry out a final check for leaks on the
pipework using a soapy solution. Never use a
flame. Also, make sure that the flexible pipe
cannot come into contact with a movlng part of
the cabinet (eg, a drawer) and that it is not situated where it could be damaged.
4
Table of gas consumption
Adapting the hob to different types of gas
To adapt the Hob for use with different types of gas, carry out the following instructions:
— remove the grids and burners
— insert the hexagonal spanner (supplied) into the burner support (Fig. 5)
— unscrew the injector and replace it with one suitable for the gas to be used (see
Table page 6).
When you have carried out the new gas regulation, replace the old gas rating plate
on your appliance with one (supplied with hob) suitable for the type of gas for which
it has been regulated.
Maxi
Fish
Double ring
Rapid
Semi rapid
Small
Total NHGC
LPG gas
Reg. 2,75 kPa
Injector size
MJ/H
Injector size
MJ/H
2x110
2x110
2x110
141
110
92
11
11
11
10
5,7
3,8
2x65
2x65
2x65
81
65
52
11
11
11
8,7
5,5
3,5
40,5
Quota «X» depending
on type of gas
LPG
NG
air. regul.
air regul.
13 mm
13 mm
15 mm
15 mm
13 mm
15 mm
4 mm
5 mm
2 mm
7 mm
6 mm
6 mm
37,4
Regulating the minimum flame
Hexagonal spanner
After lighting the burners, turn the control knob to the minimum setting and then remove the knob (this can easily be removed by apply a gentle pressure).
Using a small «Terminal» type screwdriver the regulating screw can be adjusted as in
Fig. 8. Turning the screw clockwise reduces the gas flow, whilst turning it anticlockwise
increases the flow – Use this adjustment to obtain a flame of approximately 3 to 4 mm
in length and then replace the control knob.
If GPL (cylinder) gas is being used, turn the screw clockwise right to the end of the
travel of the by-pass.
Fig. 5
Screws
regulating
REGULATING THE BURNERS
Flame Combustion
For maximum efficiency from the burners, the correct combustion of the flame is necessary. A good flame must be well aligned and without yellow tips (Fig. 7/B). If there
is insufficient air, the flame will be uneven with yellow tips (Fig. 7/A). If there is too much
air, the flame will be very short and bright (Fig. 7/C). In these cases the combustion
must be adjusted by re-fitting the carburation tube to the Venturi (where there is insufficient air) or removing the carburation tube (in the case of too much air). To position
the carburation tube, the fixing screws must be loosened, and retightened when the
satisfactory combustion is obtained.
For dimensions «X» see attached table
SMALL
MEDIUM
LARGE
BURNER CAP
Natural gas
Reg. 1,0 kPa
Burner
FIXING
SCREW
Gas tap calibrating screws
(flat head slot type)
Fig. 8
PRESSURE ADJUSTMENT
First turn the gas off to the appliance. Remove the sealing screw from the regulators
test point at the rear of the appliance and fit the hose of the Manometer to it.
Turn the gas on and light the Wok Burner and one Medium Burner at maximum setting. Check the pressure and adjust at the regulator if necessary to the settings in the
table below or on the Data plate.
For Propane Gas adjust at the regulator on the cylinder - Turn regulator adjusting
screw clockwise increases pressure whilst anti-clockwise decreases pressure. Refit
the test point sealing screw when finished.
BURNER
INSTRUCTIONS FOR USE
Using the gas Burner
AIR REGULATION
SCREW
DOUBLE RING
MAXI
FISH
Fig. 6
5
Fig. 7
To ignite the burners, place a lighted taper close to the burner, press in and turn the
control knob anti-clockwise.
If the burners have not been used for a couple of days, wait for a few seconds before
lighting the burner, this will allow any air present in the pipes to escape.
For appliances equipped with electronic ignition, simply press down and turn the control knob to the position marked with a star ★.
6
After the burner ignites, turn the knob to the control setting required.
The ignition is by repetitive spark generation; in case the burner does not light at once,
keep the knob in the ignition position for a maximum of 5 seconds.
If the burner does not ignite in this time, switch off the control knob and repeat the operation again.
As a safety device, some models automatically cut off the gas supply if the flame is
accidently extinguished. In this case, push and rotate the control knob until the ★ position and keep it held down for approx 5-6 seconds.
The burner will then remain lit.
Only pans which have smooth flat bases should be used on the electric hotplates. The
size of the pan should be as close as possible to the diameter of the hotplate, and never smaller (see Fig. 9). The base of the pan should be dry and spillages should be
avoided. Empty pans should not be left on the plates, nor should the plates left switched
on without a pan.
YES
NO
NO
NO
NO
ATTENTION: When cleaning the hob, take care to replace the burners correctly,
this will ensure that the ignition point is not blocked.
GENERAL ADVICE
For the best results, the flat-bottomed pans size should match the gas burner size as
follows:
— Small
from 6 to 12 cm.
— Medium
from 12 to 18 cm.
— Large
from 18 to 24 cm.
— Double ring
from 24 to 28 cm.
— Maxi
from 24 to 28 cm.
— Fish
from 26 to 28 cm.;
Rectangular pan max 210x370 - min. 150x290 mm.
For smaller containers the gas burner should be regulated so that the flame does not
overlap the base of the pan. Vessels with concave or convex base should not be used.
WARNING: If a burner is accidentally extinguehed, turn the knob to the off position and do not attempt to re-ignite if for at least 1 minute.
To protect the glass lid from damage and in the interests of safety, the burners/plates must be
turned off and the burner/pan support/plate area must be cool before closing the lid down.
Mijorose burner: the heat diffusing plate, to be used only on the rear right hand
burner, is designed to provided a particularly delicate cooking facility. When
this facility is not required, the burner can be used in the conventional way.
Use of electric hotplates (electric hotplates)
For the best use of the electric hotplates and to minimise energy consumption, the following recommendations should be noted.
POWER OUTPUT - ELECTRIC HOTPLATES
Setting
0
OFF
1
VERY LOW
2
LOW
3
MODERATE
4
MEDIUM
5
HIGH
6
VERY HIGH
Warming dishes & melting butter and chocolate
Simmering, sauces, stews, milk puddings, poached eggs
Vegetables, frozen foods, boiling water
Fresh Vegetables, pasta, fish, pancakes.
Omelettes, steaks
Chops
A neon indicator light adjacent to the control knob will glow when the electric plate is
in use.
7
Fig. 9
THE GAS HOBS WITH ONE ELECTRIC
PLATE ARE FITTED WITH A PAN SUPPORT TO BE USED FOR RESTING PNA
WHEN THE PLATE IS NOT IN USE.
WHEN THE HOTPLATE IS SWITCHED
ON THE PAN SUPPORT MUST BE LIFTED UP TO ALLOW THE PAN TO BE
PLACED IN DIRECT CONTACT WITH
THE HOTPLATE.
Fig. 10
MAINTENANCE AND CLEANING
Important Advice
Before cleaning the Hob, ensure the appliance has cooled down. Remove the plug from
the socket or (if connected directly) switch off the electricity supply.
When cleaning the enamelled, varnished or chrome sections, use warm soapy water
or a non caustic detergent. For stainless steel use an appropriate cleaning solution.
Hotplates should only be cleaned with a cotton cloth coated with vaseline or seed oil.
Never use abrasives, corrosive detergents, bleaching agents or acids. Avoid any acid
or alkaline substances (lemon, juice, vinegar etc.) on the enamelled, varnisched or stainless steel sections.
The burners can be cleaned with soapy water. To restore their original shine, use a
household stainless steel cleaner. After cleaning, dry the burners and replace.
It is important the Burners are replaced correctly.
The appliance is not intended for use by young children or infirm persons without supervision. Young children should be supervised to ensure that they do not play with
the appliance.
This appliance must only be used for the purpose for which it is intended, domestic
cooking, and any other use will be considered improper and could therefore be dangerous. The Manufacturer will not be responisble for any damage or loss resulting from
improper use.
8
INSTRUCTIONS FOR ASSEMBLY OF THE HOB
TO THE GAS SUPPLY PIPES
Lubricating the gas taps
If a gas tap becomes stiff, it should be dismantled, cleaned carefully with petrol and
smeared with a drop of special heat resistant grease.
The following operations should be carried but:
— disconnect the electrical power supply, close the gas supply tap from the mains or
cylinder.
— Remove the hob top plate by removing the corner screws and those under the
burners.
— Remove the two screws holding down the head flange.
— Remove the head flange and the retaining spring on the knob shaft.
— Remove the gas regulation cone, clean it with petrol and smear it with some heat
resistant grease, taking care not to obstruct any holes through which gas must pass.
— Re-assemble all the parts, making sure that the spring and the rotating axis of the
cone fitted to the knob shaft are correctly seated.
These instructions are for Fitters qualified for installation of equipment in line with the
relevant national standard. All work must be carried out with the electricity supply disconnected.
ASSEMBLY PROCEDURE
2 Spanners, sizes 17 and 23 mm are required.
1/2 GAS
Aftercare
Before calling out a Service Engineer please check the following:
— that the plug is correctly inserted and fused;
— that the gas supply is not faulty.
If the fault cannot be identified:
switch off the appliance — do not tamper with it — call the Aftercare Service Centre.
The appliance is covered by a 12 month Guarantee giving free Aftercare Service.
A) As illustrated, assemble parts in sequence:
A) fixed pipe
B) washer
C) Elbow fitting with
tapered thred
connection
2) Tighten the joints
with the Spanners,
remembering to twist
the pipes into position
before tightening.
3) Attach fitting C to
mains gas supply using rigid copper pipe
or flexible steel pipe.
VERY IMPORTANT
For ease of installation and to avoid gas leaks, it is recommended to connect the pipes as follows:
First connect the pipe to the Hob
and then
Connect the pipe to the gas supply.
In this sequence is not followed, there is a danger that gas will be trapped
in the pipe.
The Manufacturer will not be responsible for any inaccuracy resulting from printing or transcript errors contained in this brochure. We reserve the right to carry out modifications to products as required, including
the interests of consumption, without prejiudice to the characteristics relating to safety or function.
AFTER INSTALLATION, CHECK THE TIGHTNESS OF ALL JOINTS USING
A SOAPY SOLUTION
9
10
Grafica R.B. - 02/2002 - Cod. 41003881
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising