Candy LS CD 934 UK User manual

Add to my manuals
17 Pages

advertisement

Candy LS CD 934 UK User manual | Manualzz
EN
User instructions
CD 934
CD 950
Congratulations!
Contents
Thank you for choosing a Candy appliance; quality dishwashers
which guarantee high performance and reliability.
Candy manufacture a vast range of domestic appliances: washing
machines, washer/dryers, cookers, microwave ovens, ovens and
hobs, refrigerators and freezers.
Ask your dealer for the catalogue with the complete range of Candy
products.
Please read this booklet carefully as it provides important information regarding the safe installation, use, and maintenance of the
machine, together with some useful advice on how to achieve the
best results from your dishwasher.
For future reference please keep this instruction booklet in a safe
place.
Guarantee & After Sales Service
This appliance is supplied with a guarantee certificate which offers
a free one year labour guarantee and a free five year parts
guarantee - see the guarantee certificate for further details.
Remember to post part A of the guarantee certificate within 10 days
of the purchase date to register your guarantee with us.
Part B should be filled in and retained by you, to be shown to the
GIAS service engineer if required. You should also keep your sales
receipt.
page
page
page
page
page
page
page
page
page
page
page
page
page
page
page
page
page
Safety advice
Setting up, installation
Opening the door
Water softener unit
Adjusting the upper basket
Loading the dishes
Half load washing
Information for test laboratories
Loading the detergent and rinse aid
Cleaning the filters
Some practical hints
Routine cleaning and maintenance
Description of the controls
Technical data
Operating the programmes and special functions
Programme selection
Identifying minor faults
Fig. A
After Sales Service
For service and repairs call your local engineer on our national
number 08705 990011
Summary of manufacturers guarantee conditions
Your new appliance is fully guaranteed by the manufacturer for 12
months against electrical/mechanical breakdown excluding:
A. Any faults which occur due to bad installation or misuse of the
machine.
B. Any faults which occur due to repair of, or interference with, the
machine by any person not authorised by the manufacturer to
carry out service.
C. Any faults which occur due to any parts which are fitted to the
machine which are not the original manufacturers parts.
D. Any faults arising from non-domestic use or unusual or abnormal
use of the machine.
E. Any faults arising from operation at incorrect voltage.
F. Any faults arising from incorrect operation of the machine.
The guarantee applies to Gt Britain and Northern Ireland only, and
is an addition to your statutory rights.
2
5
1
4
2
3
3
4
5
8
9
11
12
15
16
16
18
19
20
22
22
23
24
26
Safety Instructions
INSTALLATION (Technical notes)
Please read the instructions in this booklet carefully because they contain important
information on how to install, use and maintain your dishwasher safely as well as
containing useful tips on how to make the most of it.
Keep this booklet safe for future reference.
There are certain basic safety rules which are valid for any domestic appliance. They
are the following:
- never touch the appliance when your hands or feet are wet or damp
- do not use when your feet are bare
- do not remove the plug from the mains supply socket by pulling the mains cable or
the machine itself
- do not leave the appliance exposed to the elements (rain, sun etc)
- do not let children (or others incapable of operating it) use the machine without
supervision
- make sure that the plug fitted to the machine is compatible with the power supply
socket. If it is not, get a suitably qualified person to fit the correct type, and to make
sure that the cables to the mains socket are able to cope with the power rating of
the appliance
- ensure that the dishwasher does not crush power cables
- if there is a water softening device installed in the home there is no need to add
salt to the water softener fitted in the dishwasher
- the dishwasher is designed for normal kitchen utensils.
Objects that have been contamined by petrol, paint, traces of steel or iron,
corrosive chemicals, acids or alkalis must not be washed in the dishwasher
- if you wish to dispose of an old dishwasher be careful to remove the door to
eliminate the risk of children becoming trapped inside it
- the dishwasher has been made from materials which can be recycled so that it can
be disposed of in an environmentally friendly way
- in general it is not advisable to use adaptors, multiple plugs and/or extension
cables
- Water left in the machine or on the dishes at the end of the wash programme
should not be swallowed.
- Leaning or sitting on the open door of the dishwasher could cause it to tip over.
- Cutlery is washed best if it is placed in the basket with the handles downwards;
however, to avoid any injury from blades or sharp points, it can be placed with the
handles upwards.
- Should it be necessary to replace the supply cord, call the Service Department.
- This appliance is designed for domestic use only.
After unpacking, adjust the height of the dishwasher.
For the dishwasher to work correctly it must be level.
Adjust the feet so that the machine does not tilt by more
than 2 degrees. If it you need to move the machine after
removing the packaging, do not try to lift it by the bottom
of the door. Follow the instructions in figure. Open the
door slightly and lift the machine by holding on the top.
Important: when the appliance is located on a
carpet floor, attention must be paid to ensure that
there is no obstruction to the bottom vents.
Make sure that the plug on the appliance remains
accessible after installation.
This appliance complies with Directives
89/336/EEC, 73/23/EEC and following changes.
If the appliance breaks down or stops working properly, switch it off, turn off the water
supply and do not tamper with it. Repair work should only be carried out by an
approved service agent and only genuine spare parts should be fitted. Any failure to
follow the above advice may have serious consequences for the safety of the appliance.
4
5
Electrical connection
Plug your dishwasher into the power socket.
If the plug we supply does not fit
• CUT IT OFF AND DESTROY IT!
You can't use it on other appliances, and the exposed wires could be
dangerous if anyone plugged it in.
• Fit a suitable plug, as follows:
Connect
to the terminal in the plug
green and yellow wire
marked with the letter E,
OR marked with the Earth symbol,
OR coloured green,
OR coloured green and yellow.
marked N
OR coloured black.
marked L
OR coloured red.
blue wire
brown wire
"WARNING"
THIS APPLIANCE MUST BE EARTHED
Fuses and plugs
This appliance should be used only on a
socket with a minimum rating of 13 Amp.
Our ready-fitted plug is already equipped
with a 13 amp fuse which is BS 1362 ASTA approved.
Any replacement should be exactly the same.
If the fuse cover is lost, do not use the plug until it is replaced.
A correct replacement fuse cover (obtainable from your dealer
or Electricity Board) must be the same colour as shown or
named on the insert on the base of the plug.
The filter D must be inserted between the tap B and the inlet hose A, remembering
to fit the washer C.
If the dishwasher is connected to new pipes or to pipes which have not been in use
for a long time run water through for a few minutes before connecting the inlet hose.
In this way no deposits of sand or rust will clog up the water inflow filter.
1
2
3
Connecting the outlet hose
The outlet hose should disharge into a standpipe, making sure that there are no kinks
(fig. 4).
The standpipe must be at least 40 cm above floor level and it must have an internal
diameter of at least 4 cm. It is advisable to fit an anti-odour air trap (fig. 4 x).
If necessary the outlet hose can be extended up to 2,6 m, provided that it is kept at
a maximum height of 85 cm above floor level.
The hose can be hooked over the side of the sink (it must not be immersed in water,
in order to prevent water from being syphoned back to the machine when this is in
operation) (fig. 4 y).
When installing the appliance under a worktop the hose pipe clamp must be attached
to the wall in the highest possible position under the worktop (fig. 4 z).
Check that there are no kinks in the inlet and outlet hoses.
4
Water connection
The inlet and drain hoses can be directed to left or right.
The dishwasher can be connected to either cold or hot water, as long as it is
no hotter than 60 °C.
Water pressure must be between 0,08 MPa and 0,8 MPa. If the pressure is below
the minimum consult our service department for advice.
The inlet hose must be connected to a tap so that the water supply can be cut off
when the machine is not in use (fig.1 B).
The dishwasher is fitted with 3/4" threaded connector (fig. 2).
Connect inlet hose A to water tap B with a 3/4" attachment making sure that it has
been properly tightened.
If it is necessary to lengthen the inlet pipe, an extension pipe can be fitted.
If limescale deposits or sand are present in the water, it is advisable to obtain the
appropriate filter, art. 9226085, from the Service Centre (fig. 3).
6
7
Installation in fitted kitchens
Closing the door
Fitting between existing cabinets
The height of the dishwasher, 85 cm, has been designed in order to allow the machine
to be fitted between existing cabinets of the same height in modern fitted kitchens.
The feet can be adjusted so that correct height is reached.
The laminated top of the machine does not require any particular care since it is
heatproof, scratchproof and stainproof (fig. 5).
The work top can be easily adjusted to line it with the top of existing cabinets; this is
done by moving it by 5 mm each time up to a maximum of 25 mm.
To adjust it, unscrew the two screws at the back and fix the top in the position
required (fig. 6).
Underneath existing work top (when fitting beneath a work top)
In most modern fitted kitchens there is only one single work top under which cabinets
and electrical appliances are fitted.
In this case remove the work top of the dishwasher by unscrewing the screws under
the rear edge of the top (fig. 6).
The height will then be reduced to 82 cm, as scheduled by the International
Regulations (ISO) and the dishwasher will fit perfectly under the kitchen working top
(fig. 7).
5
6
Water softener unit
Depending on the source of the supply, water contains varying amounts of limestone
and minerals which are deposited on the dishes leaving whitish stains and marks.
The higher the level of these minerals present in the water, the harder the water is.
The dishwasher is fitted with a water softener unit which, through the use of special
regenerating salt, supplies softened water for washing the dishes. The softener unit
can treat water with a hardness of up to 60°fH (French grading) or 33°dH (German
grading) through five different settings.
The degree of hardness of your water can be obtained from your water supply
company.
Regulating the water softener
The table below lists different degrees of water hardness with the corresponding setting
for the softener unit.
Level
0
1
*2
3
4
7
598
556/563
Opening the door
Put your hand into the recess and push upwards.
If the machine comes open while it is working, an electrical safety device
automatically switches everything off.
For the machine to work properly, the door should not be opened while it is in
operation.
8
Place the baskets in the machine.
Make sure that both the spray arms are free to rotate and are not obstructed by
cutlery, crockery or pans. Close the door, pressing on it to make sure it is firmly shut.
Water
hardness
°fH
(french)
Water
hardness
°dH
(German)
Use of
regenerating
salt
0-9
10-30
31-40
41-50
51-60
0-5
6-16
17-22
23-27
28-33
NO
YES
YES
YES
YES
- *The water softener unit is set in the factory at level 2, as this is suitable for the
majority of users.
If your water is at level 0, you need not
use any regenerating salt, nor need you
make any adjustment, as your water is
soft.
According to the degree of hardness of
your water, regulate the softener unit in
the following way:
- remove the lower rack. Unscrew and
remove the cap from the salt dispenser
located in the bottom of the tub (Fig. A “1”);
- Turn the selector screw to the required
position with a screwdriver or a knife.
9
Water
softener
setting
FREE
N.1
N.2
N.3
N.4
position
position
position
position
N°
of
washes
50
40
30
20
TYPE 1
TYPE 2
Loading the salt
Adjustment of the upper basket
The dishwasher is fitted with a softener which
clears the water of lime which could cause scale
and damage the dishwasher.
On the bottom of the machine there is a container
for the salt for regenerating the softener.
The filter medium of the softening plant must be
reactivated with dishwasher water softener
regenerating salt.
Other types of salt contain small quantities of
insoluble particles which over a long period of
time may affect and deteriorate the softener
performance.
To add salt, unscrew the cap of the container on
the bottom and then refill the container.
During this operation a little water will overflow; but keep adding salt until the container
is full. When the container is full, clean the thread of salt residue and retighten the
tap.
If the dishwasher is not required straightaway, set the Prewash programme so that
the salt solution which has overflowed is discharged from the washing tank.
The salt dispenser has a capacity of between 1.5 and 1.8 kg and, for efficient use of
the appliance, it should be refilled from time to time according to the regulation of the
water softener unit.
Important: it is necessary to add water until the container overflows. Only
install the dishwasher after completely filling the salt container.
If 27 cm to 31 cm plates are normally used, load them onto the lower basket after the
upper basket has been placed in its upper position and proceed as detailed below :
1) Pull out the upper basket;
2) Then grasp the basket from both sides and lift it upwards (fig. 1).
Dishes that are bigger than 20 cm in diameter can no longer be loaded onto the
upper basket and the mobile supports cannot be used when the basket is in the
upper position.
ADJUST BASKET TO THE LOWER POSITION:
1) Grasp the basket from both sides and lift slightly upwards (fig. 2a);
2) Then slowly release into the correct position (fig. 2b) .
N. B. : NEVER LIFT OR LOWER THE BASKET BY ONE SIDE ONLY (fig.3).
Attention :
It is advisable to adjust the basket before loading the dishes.
1
2
a
b
a
b
Salt loading indicator
This model is provided with an indicator light on the control panel which will light
up when it is necessary to reload the salt container.
Important: the appearance of white stains on dishes is generally an important sign
that the salt container needs filling.
10
11
3
A standard daily load is represented in Figs.
1, 2 and 3.
1
Loading dishes
To load dishes
For good wash performance remove any debris from the dishes (bones, tooth picks,
the remains of meat and vegetables) to avoid blocking the filters, water outlet and
washing arm nozzles and, as a result, reducing washing efficiency.
Try not to rinse the dishes before loading them into the dishwasher.
If saucepans and oven dishes are encrusted with the remains of burnt or roast food,
it is advisable to leave them to soak before washing.
E
A
C
B
D
Using the upper basket
The upper basket is provided with mobile racks hooked to the sides of the basket
which can be regulated in two positions: upright and lowered. In the lowered position
the racks may be used for tea and coffee cups, kitchen knives and ladles. Glasses
with stems may be safely hung on the ends of the racks.
Glasses, cups, saucers and dessert plates may be loaded under the racks.
Upper basket (Fig. 1)
A = soup plates
B = dinner plates
C = dessert plates
D = saucers
E = cups
F = glasses
F
2
Upper basket (Fig. 2)
A = soup plates
B = dinner plates
C = dessert plates
D = saucers
E = cups
F = glasses with stems
G = glasses
H = single section cutlery basket
Soup plates and ordinary plates may be loaded with the rack in the upright position.
Plates should be loaded vertically with the underside of the plate towards the back of
the dishwasher with a space between each plate to allow water to pass freely.
A
It is advisable to load plates of the same size together in order to utilize maximum
basket capacity.
Plates may be loaded in a single row (Fig. 1) or on both rows (Fig. 2).
B
C
D
It is advisable to load large plates (approx. 27 or more cm) slightly tilted towards the
rear to facilitate introduction of the basket into the machine.
Salad bowls and plastic bowls may also be loaded on the upper basket. It is advisable to block these in place so that the jets of water do not make them overturn.
F
3
The upper basket has been designed to offer maximum flexibility in use and can be
loaded with up to 24 plates on two rows, up to 30 glasses on five rows or a mixed
load.
Using the lower basket
Saucepans, oven dishes, tureens, salad bowls, lids, serving dishes, dinner plates,
soup plates and ladles can be loaded on the lower basket.
Place the cutlery in the plastic cutlery holder with the handles pointing upwards.
Place the cutlery holder on the lower basket (fig. 3), making sure that the cutlery does
not get in the way of the rotating arms.
G E
H
D
B
F
A G
E
C
12
Lower basket (Fig. 3)
A = medium-sized saucepan
B = large saucepan
C = frying pan
D = lids
E = tureens, serving dishes
F = cutlery
G = oven dishes
Please load the dishwasher sensibly to
ensure the best wash results.
13
Cutlery basket (fig. 7)
7
12 international place load (Ref. EN 50242).
The cutlery basket is made with two
detachable parts which will enable various
loading options.
The two parts can be detached by sliding the
left section away from the right section.
Correct loading for the upper basket is indicated in Fig. 4 and for the lower basket
in Fig. 5. Fig. 6 cultery basket.
4
G
B
E
C
D
H
Upper basket (Fig. 4)
C
I
F
C
H
A
5
L
Q
M
N
P
N
A
B
C
D
E
F
G
H
I
L
= 5 + 5 + 2 glasses
= 12 saucers
= 4 + 4 + 4 cups
= small bowl
= medium bowl
= large bowl
= 1 + 1 forks
= 1 + 1 serving spoons
= 3 + 3 + 3 + 3 dessert spoons
= 3 + 3 + 3 + 3 teaspoons
Lower basket (Fig. 5)
M
N
O
P
Q
=
=
=
=
=
8 + 4 soup plates
11 + 1 dinner plates
12 dessert plates
serving dish
cutlery
Half load wash upper basket
1
E
M
I
O
1/2 mixed load (fig. 1)
CD H B
F
L M G A
A
B
C
D
E
F
G
H
I
L
M
=
=
=
=
=
=
=
=
=
=
=
glasses
cups
soup plates
dinner plates
dessert plates
saucers
saucepan
lid
Irying pan
medium bowl
small bowl
Cutlery basket (fig. 6)
6
R
Place the side racks in the lower position
and fill with 6 + 6 knives(R); in the spaces
left insert cutlery with the handles down.
Take care not to load more than two different
types of cutlery in the same compartment.
C
2
D
A
B
C
D
E
F
G
H
I
F
E
I
14
1/2 load standard (fig. 2)
B
H
G
A
=
=
=
=
=
=
=
=
=
6 glasses
5 + 1 cups
serving dish
6 soup plates
6 dinner plates
6 dessert plates
6 saucers
medium bowl
small bowl
Place the cutlery in the plastic cutlery holder on
the lower basket.
15
Information for the test laboratories.
General programme comparison
(see programmes selection)
If you select a programme with a prewash cycle, the performance will be improved by
adding a small amount of detergent during this part of the cycle.
CAUTION! IMPORTANT NOTE ON THE USE OF COMBINED DETERGENTS
If you are planning to use combined detergents i.e. those with built in salt and/or rinse
agent, we would advise the following:
Ref. EN 50242 Standards:
1) Upper basket position: low
2) Normal load
3) Shine setting: 5
4) Amount of detergent:
– 8 gr for pre-wash
– 22 gr for wash.
- read carefully and follow the manufacturer’s instructions given on the packaging;
- some combined detergents, particularly those with built in rinse agent, provide best
results when used with specific programmes;
- the effectiveness of detergents containing the built in water softener/salt depends on
the hardness of your water supply. Check that the hardness of your water supply is
within the effective range given on the detergent packaging.
In certain circumstances use of combined detergents can cause:
Loading the detergent and the rinse aid.
Filling the detergent container
It is essential to use a detergent that is specifically designed for dishwashers
either in powder, liquid or tablet form.
Unsuitable detergents (like those for washing up by hand) do not contain the proper
ingredients for use in a dishwasher and stop the dishwasher from working correctly.
Normal wash
The detergent container is inside the door
(fig. A “2”). If the lid of the container is closed
press the button to open.
At the end of every wash cycle the lid is
always open and ready for the next time the
dishwasher is used.
The amount of detergent to be used varies
according to how dirty the dishes are and on
the type of dishes to be washed.
We advise using 20-30 gr of detergent in the
wash section of detergent compartment (1).
- limescale deposits on dishes or in the dishwasher;
- a reduction in washing and drying performance.
Should this occur, we would recommend using traditional separate products – salt,
detergent and rinse agent. This will ensure that the water softener in the dishwasher
operates correctly.
Please note that on return to the use of conventional salt, a number of cycles will be
required before the system becomes fully efficient again.
NOTE
Any problems which arise as a direct result of the use of these products are not
covered by our warranty.
Filling the rinse aid container
4
3
FULL
EMPTY
dark
light
After pouring the detergent into the
container close the lid.
Since not all detergents are the same the instructions on the boxes of detergent can
vary. We should just like to remind users that too little detergent does not clean the
dishes properly whilst too much detergent will not produce better results and is also
a waste. Do not use an excessive amount of detergent and help limit damage to the
environment at the same time.
Regulating the rinse aid from 1 to 6
Wash with soaking cycle (prewash)
If setting the Universal Intensive wash programme, a second dose of about 20 gr
of detergent (1 table-spoon) must be added to the machine in the prewash section of
detergent compartment (2).
16
The rinse aid container can be found to the right of the
detergent container: it has a capacity of about 130 ml
(fig. A "3").
Turn the cap (3) anticlockwise and pour enough liquid to last
several washes, up to the maximum level shown. Replace
the cap.
The rinse aid, which is automatically released during the
last rinsing cycle, helps the dishes to dry quickly and
prevents spots and stains forming.
It is always advisable to use rinse aid.
Check the rinse aid level through the indicator eye which is
situated in the centre of the dispenser (4).
3
The regulator is placed under the cap (3) and can be
turned using a coin. The recommended position is 3.
The limestone content of the water considerably affects the
formation of limescale and the drying performance.
It is therefore important to regulate the quantity of rinse
aid to achieve good washing results.
If, after the wash, streaks occur on the dishes, decrease
the amount by one position. If whitish spots occur, increase
the amount by one position.
17
Practical hints
Cleaning the filters
1
2
3
The filter system (fig.A “4”) consists of:
a central container that traps the larger
particles.
a flat gauze that continuously filters the
wash water
a micro filter, located beneath the gauze,
that traps the tiniest particles ensuring a
perfect rinse.
To achieve excellent results every time, the
filters should be checked and cleaned after
each wash.
To remove the filter unit, simply turn the
handle anticlockwise (fig. 1).
For ease of cleaning, the central container is
removable (fig. 2).
Remove the gauze filter (fig.3) and wash the
whole unit under a jet of water. If necessary
a small brush can be used.
With the Self-cleaning Micro filter, maintenance is reduced and the filter unit need only
be checked every two weeks. Nevertheless,
after each wash it is advisable to check that
the central container and the gauze filter are
not clogged.
NB: after cleaning the filters, make sure
that they are correctly reassembled and
that the gauze filter is properly positioned
at the bottom of the dishwasher.
Make sure that the filter is screwed back,
clockwise, into the gauze, as poor
seating of the filter unit could have an
adverse effect on the efficiency of the
appliance.
Warning: never use the dishwasher
without the filters.
Selecting the programme
This dishwasher offers you a wide range of wash programmes so that you can choose
the most suitable according to the type of dishes and how dirty they are.
Refer to the PROGRAMME LIST to choose the most suitable programme.
Useful hints
In order to avoid any dripping from the top rack, remove the lower rack first.
If the dishes are to be left in the machine for some time, leave the door ajar, to let
some air circulate and to improve the drying performance.
How to make SAVINGS
1) If you want the dishwasher to give a complete wash, place the dishes in the
dishwasher at the end of each meal and if necessary turn on the COLD PRE-WASH
cycle to soften the food remains and remove bigger particles of food from the new
load of dishes. When the dishwasher is full start the complete wash cycle programme.
2) If the dishes are not very dirty or if the baskets are not very full select an
ECONOMY programme, following the instructions in the program list.
How to get really good wash RESULTS
1) Place the dishes face downwards.
2) Try to place the dishes in such a way that they are not touching one another. If
they are loaded properly you will get better results.
3) Before placing the dishes in the dishwasher remove any remaining food (bones,
shells, pieces of meat or vegetables, coffee grounds, skin of fruit, cigarette ash etc.
that could clog up the outflow and the washing arm jets.
4) After loading the dishes check that the washing arms can rotate freely.
5) Pans and other dishes that have particularly stubborn food particles or remnants
of burnt food should be left to soak in water with dishwasher detergent.
6) To wash silver properly:
a) rinse the silver immediately after use, especially if it has been used for mayonnaise,
eggs, fish etc.
b) do not sprinkle detergent onto it
c) keep it separate from other metals
What to DO if
1) You want to stop the dishwasher to put in more dishes whilst it is in the middle of
a wash.
Open the door only after pressing the O/I button so that the dishwasher is in OFF.
After closing the door, wait 3 minutes before starting up the machine again.
What not to wash
It should also be remembered that not all dishes are suitable for washing in a
dishwasher.
We advise against using the dishwasher to wash items in thermoplastic, cutlery with
wooden or plastic handles, saucepans with wooden handles, items in aluminium,
crystal, leaded glass unless otherwise stated.
Certain decorations may fade. It is therefore a good idea before loading the whole
batch to wash just one of the items first so as to be sure that others like it will not fade.
It is also a good idea not to put silver cutlery with non-stainless steel handles into the
dishwasher as there could be a chemical reaction between them.
IMPORTANT
When buying new crockery or cutlery always make sure that they are suitable for
washing in a dishwasher.
18
19
Cleaning and maintenance
The outside of the cabinet can be cleaned with a non-abrasive cleaning agent
suitable for a gloss finish.
The dishwasher does not require special maintenance, because the tank is selfcleaning. Regularly wipe the door gasket with a damp cloth to remove any food
remains or rinse aid. It is advisable to remove limestone deposits or dirt periodically,
by doing an empty wash; pour a glass of vinegar on the bottom of the tank and select
the light wash.
If, in spite of the routine cleaning of the filters, you notice that the dishes or pans are
not properly washed or rinsed, check that all the spray heads on the rotor arms
(fig. A “5”) are clear.
If they are blocked, clean them in the following way:
To remove the upper rotor arm, turn it until it lines up with the stop marked by the
arrow (fig. 1b). Push it upwards and, keeping it pushed in, unscrew it in a clockwise
direction. To reassemble it repeat the same operation, but turn it anticlockwise.
The lower rotor arm can be removed simply by pulling it upwards (fig. 2).
• wash the rotor arms under a jet of water to clear any blockage in the spray heads.
• When you have finished, refit the rotor arms in the same position, remembering to
re-align the arrow and screw into position.
1
The water heater element is made of a special stainless steel which after a while may
change colour; this does not in any way affect its performance or its working life.
Both the door lining and the tank lining are in stainless steel; however, should spots
caused by oxidation occur, this is probably due to a high level of iron salts presents
in the water. The spots can be removed with a mild abrasive agent; never use
chlorine based materials, steel wool, etc.
WHEN CYCLE IS FINISHED
After every wash it is essential to turn off water supply and to switch off the machine
by pressing the On/Off button to the off position. If the machine is not going to be
used for some time, it is advisable to follow these rules:
1. do an empty wash with detergent in order to clean the machine of any deposits.
2. pull out the electric plug.
3. turn off the water tap.
4. fill the rinse aid container.
5. Ieave the door ajar.
6. Keep the inside of the machine clean.
7. If the machine is left in places where the temperature is below 0°C any water left
inside the pipes may freeze. Wait until the temperature rises above zero and then
wait for about 24 hours before starting up the dishwasher.
2
1b
20
21
Attention
This dishwasher is equipped with an anti-overflow safety device
which works even when power is switched off, and if the water
level is too high the supply will automatically be closed off.
Important
To ensure the correct operation of the anti-overflow safety
device, it is recommended not to move or to tilt the dishwasher
during operation.
If it is necessary to move or to tilt the dishwasher, first make
sure the washing cycle is finished and that no water is left in
the tank.
Description of the controls
H
I
L
Selecting the programme and special functions
A B C D
F
G
Use in conjunction with programme guide
A
On/off button
G
Programme selector
B
“65°C INTENSIVE” button
H
Mains indicador light
C
“HALF LOAD” button
I
Low level salt indicator light
D
“QUICK WASH” button
L
Low level rinse aid indicador light
F
To set the programme, turn the dial clockwise until the pointer
( ) indicates the symbol of the required programme on the
control panel. Then press the On/Off button. Ensure that the
water supply is turned on and the door is closed properly.
65°C
INTENSIVE
Door handle
“65°C INTENSIVE” button
This button is an option available on the “UNIVERSAL INTENSIVE”
and “DAILY INTENSIVE” programmes which will increase the
temperature of the water of washing from 50°C to 65°C.
Dimensions:
Height
Depth
Width
Depth with door open
with working top
without working top
85
60
60
120
82
56,3
59,8
117
cm
cm
cm
cm
Technical Data
EN 50242 place load
Capacity with pans and dishes
Water supply pressure
Fuse
Power input
Supply voltage
12
8 persons
Min. 0,08 - Max 0,8 MPa
(see rating plate)
(see rating plate)
(see rating plate)
22
HALF
LOAD
“HALF LOAD” button
By pressing this button it is possible to wash a small quantity
of crockery using only the upper basket for dishes and cutlery
in the bottom basket. This reduces water and energy
consumption and requires a smaller quantity of detergent as
well.
QUICK
WASH
“QUICK WASH” button
The “QUICK WASH” button combined with the delicate
programme washes lightly soiled dishes in 32 minutes.
IMPORTANT:
When this button is selected, the programme finishes at the
first STOP position on the programme dial. If this option is
not selected a normal delicate programme will be run and
will finish at the second STOP position.
23
PROGRAMME SELECTION
Short cold pre-wash for items that are
stored in the dishwasher until you are
ready to wash a full load.
COLD RINSE
+ 65°C
UNIVERSAL
BUTTON INTENSIVE
Once a day - for heavily soiled pans and
any other items that have been left all day
for washing.
ECO UNIVERSAL
+ 65°C
BUTTON DAILY INTENSIVE
Once a day - for normal soiled pans and
any other items that have been left all day
for washing.
• • • • •
• • • •
DAILY
Suitable for heavily soiled items that are to
be washed straight after a meal.
• • • •
DELICATE
50°C
Suitable for delicate crockery and
glassware. Also for less soiled items
excluding pans.
+ QUICK
RAPID 32’
50°C BUTTON
50°C
PLATE-WARMING
65°C
24
6
150
YES
YES
YES
•
• •
135
50°C
•
105
YES
• • • •
50°C
•
75
YES
Quick wash for dishes which are to be
washed immediately after the meal. Wash
load of 4/6 persons.
• • • •
50°C
•
32
YES
Suitable for rinsing dishes which have not
been used for some time and for warming
dishes prior to serving.
• •
65°C
•
55
YES
•
50°C
65°C
25
110
“QUICK WASH”
button
“HALF LOAD”
button
Special function
buttons available
“65°C INTENSIVE”
button
With cold water
(15°C)
Hot rinse with
rinse aid
Intermediate rinse
Main wash
Cold pre-wash
Hot pre-wash
•
•
• • • • • • 65°C • •
Energy Saving Programme suitable for
normal soiled items. Using detergents with
enzyme.
Programme standardised to EN 50242.
50°C
Average
duration in
minutes
Programme contents
Check salt container
Check rinse aid
dispenser
Clean filter
Description
Detergent for
washing
Programme
Detergent for
soaking (prewash)
Check list
YES
YES
YES
YES
FAULT
Identifying minor faults
Warning!
Before removing any panel: 1. Turn the knob to STOP.
2. Pull the electric plug out.
Should the dishwasher fail to operate, before contacting the Service Centre, make the
following checks:
FAULT
1 - Machine completely dead
2 - Machine does not
draw water
3 - Machine does not
discharge water
4 - Machine discharges water
continuously
5 - Spray arms are not heard
to rotate
6 - On electronic appliances
without a display: “eco”indicator light and indicator light
“No.1” with audible signal
are heard.
7 - On electronic appliances with
a display: “E1” appears on the
display with audible signal.
CAUSE
CAUSE
REMEDY
See causes for no. 5
Check
Bottom of saucepans have not
been washed well
Burnt on food remains must
be soaked before putting pans
in dishwasher
Edge of saucepans have not
been washed well
Reposition saucepans
Spray arms are partially blocked
Remove spray arms by
unscrewing ring nuts clockwise
and wash under running water
The dishes have not been
properly loaded
Do not place the dishes too
closely together
The end of the outlet hose is in
the water
The end of the outlet hose
must not come into contact
with the outflow water
The incorrect amount of
detergent has been measured
out; the detergent is old and hard
Increase the measure
according to how dirty the
dishes are and change detergent
The wash programme is not
thorough enough
Choose a more vigorous
programme
The lower basket dishes have
not been washed
Depress half load button
Water is too hard
Check salt and rinse aid level
and regulate amount.
Should the fault persist,
Contact Service Centre
Load dishes better onto the
basket
REMEDY
Plug is not connected to wall
socket
Connect electric plug
O/I button has not been pressed
Press button
Door is open
Close door
No electricity
Check the fuse in the plug and
the electricity supply
See causes for no. 1
Check
Water tap is turned off
Turn water tap on
Programme selector is not at
correct position
Turn programme selector to
correct position
The inlet hose is bent
Eliminate the bends in the hose
The inlet hose filter is not
correctly connected
Clean the filter at the end of the
hose
Filter is dirty
Clean filter
Outlet hose is kinked
Straighten outlet hose
The outlet hose extension is
not correctly connected
Follow the instructions for
connecting the outlet hose
carefully
The outlet connection on the
wall is pointing downwards not
upwards
Call a qualified technician
Position of outlet hose is too
low
Lift outlet hose to at least 40 cm
above floor level
Excessive amount of detergent
Reduce amount of detergent
Use suitable detergent
Item prevents arms from rotating
Check
Plate and cup filter very dirty
Clean plate and cup filter
N.B.: Should any of the situations occur and should the machine give a bad wash performance, it is
necessary to remove the deposits from the dishes by hand since the final drying cycle hardens the
deposits which a second wash in the machine would not be able to remove.
Water inlet tap turned off
Switch off the appliance.
Turn on the tap.
Re-set the cycle.
If the malfunction continues contact a Service Centre quoting the serial number of the dishwasher.
This is found on the plaque on the inside of the dishwasher door at the top or on the guarantee.
This information will make it possible to take more effective action more quickly.
Water inlet tap turned off
26
Switch off the appliance.
Turn on the tap.
Re-set the cycle.
8 - Load of dishes is only
partially washed
9 - Presence of white spots
on dishes
10 - Noise during wash
11 - The dishes are not
completely dry
The dishes knock against one
another
The revolving arms knock against
the dishes
Load dishes better
Inadequate air flow
Leave the dishwasher door ajar
at the end of the wash program
to allow the dishes to dry naturally
The manufacturers decline any responsability for any printing mistakes in this instruction booklet. They also reserve the right to modify their
own appliances as necessary without altering the essential characteristics.
27
The manufacturer declines all responsibility in the event of any printing mistakes in this
booklet. The manufacturer also reserves the right to make appropriate modifications to
its products without changing the essential characteristics.
02.10 - 41003434.A - Printed in Italy - Imprimé en Italie
EN

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Download PDF

advertisement