Candy | CDIN 2L360PB-80 | Candy CDIN 2L360PB-80 User manual

Candy CDIN 2L360PB-80 User manual
EN
Thank you for choosing a Candy dish
washer. We are confident it will assist you
loyally in washing your daily dishes in full
safety.
Contents
1. GENERAL SAFETY RULES
2. WATER CONNECTION
Carefully read this manual for correct and
safe appliance use and for helpful tips on
efficient maintenance.
3. LOADING THE SALT
4. ADJUSTING THE UPPER BASKET
(SAME MODELS ONLY)
Only use the dish washer after
carefully reading these instructions. We
recommend you always keep this manual
to hand and in good condition for any
future owner.
5. LOADING DISHES
Please check that the appliance is
delivered with this instruction manual, the
warranty certificate, the service centre
address and the energy efficiency label.
Each product is identified by a unique 16digit code, also called the “serial number”,
printed on the warranty certificate or on
the serial plate found inside the door, on
the upper right hand side. This code is a
sort of product-specific ID card that you
will need to use to register the product or
if you need to contact the Technical
Assistance Centre.
8. TYPES OF DETERGENT
6. INFORMATION FOR TEST
LABORATORIES
7. LOADING THE DETERGENT
9. LOADING THE RINSE AID
10.CLEANING THE FILTERS
11.PRACTICAL HINTS
12.CLEANING AND MAINTENANCE
13.DESCRIPTION OF THE CONTROL PANEL
14.TECHNICAL DATA
15.PROGRAMME SELECTION AND SPECIAL
FEATURES
16.REMOTE CONTROL (Wi-Fi)
Fig. A
17.PROGRAMME LEGEND
18.WATER SOFTENER UNIT
19.TROUBLESHOOTING AND WARRANTY
5
20.ENVIRONMENTAL CONDITIONS
1
A. WIRELESS PARAMETERS (PAG.36)
4
3
2
2
l This
appliance is intended to
be used in household and
similar applications such as:
− Staff kitchen areas in
shops, offices and other
working environments;
− Farm houses;
− By clients in hotels, motels
and other residential type l Children should be supervised
environments;
to ensure that they do not play
− Bed and breakfast type
with the appliance.
environments.
A different use of this appliance l Children of aged 3 and under
should be kept away unless
from household environment
continuously supervised.
or from typical housekeeping
functions, as commercial use by
expert or trained users, is excluded l If the supply cord is damaged,
even in the above applications. If
it must be replaced by the
the appliance is used in a manner
manufacturer, its service agent
inconsistent with this it may reduce
or similarly qualified persons in
the life of the appliance and may
order to avoid a hazard. We
void the manufacturer’s warranty.
recommend using an original
Any damage to the appliance or
component, which can be
other damage or loss arising
requested from the Technical
through use that is not consistent
Assistance Centre.
with domestic or household use
(even if located in a domestic or
l Only
use
the
hose-sets
household environment) shall not
supplied with the appliance for
be accepted by the manufacturer to
the water supply connection
the fullest extent permitted by law.
(do not reuse old hose-sets).
l This
appliance can be used by
children aged from 8 years and l Water pressure must be
above and persons with reduced
between 0.05 MPa and 0.8
physical, sensory or mental
MPa.
3
EN
capabilities or lack of experience
and knowledge if they have been
given supervision or instruction
concerning use of the appliance
in a safe way and understand the
hazards involved. Children shall
not play with the appliance.
Cleaning and user maintenance
shall not be made by children
without supervision.
1. GENERAL SAFETY
RULES
l Make
sure carpets or rugs do The manufacturer declines all
not obstruct the base or any of responsibility for any damage
the ventilation openings.
to people or property due to
non-earthing of the machine.
l After installation, the appliance
must be positioned so that the
l Ensure that the dishwasher
plug is accessible.
does not crush power cables.
l In
general it is not advisable to
use adaptors, multiple plugs
and/or extension cables.
WARNING:
Knives and other utensils
with sharp points must be
loaded in the basket with
their points down or placed
in a horizontal position.
l Before
cleaning or maintaining
the dishwasher, unplug the
appliance and turn off the
water supply.
l Do
not leave the door open in
a horizontal position, in order
to avoid potential dangers (e.g. l Do not pull on the power cord
tripping).
or appliance to unplug the
machine.
l For further information on the
product or to consult the technical
data sheet, please refer to the l Do not leave the appliance
exposed to the elements (rain,
manufacturer's website.
sun, etc.).
Electrical connections
safety instructions
and
l Leaning
or sitting on the open
door of the dishwasher could
cause it to tip over.
l The
technical details (supply
voltage and power input) are
indicated on the product rating
l The dishwasher is designed for
plate.
normal kitchen utensils. Objects
that have been contamined by
l Make sure that the electrical
petrol, paint, traces of steel or
system is earthed and complies
iron, corrosive chemicals, acids
with all applicable laws, and
or alkalis must not be washed in
that the socket is compatible
the dishwasher.
with the plug of the appliance.
4
there is a water softening
device installed in the home
there is no need to add salt to
the water softener fitted in the
dishwasher.
By
marking this product,
we confirm, under our own
responsibility, full compliance
of this product with all
relevant safety, health and
environmental requirements
l If the appliance breaks down or
stops working properly, switch it under European legislation.
off, turn off the water supply and
do not tamper with it. Repair work Installation
should only be carried out by an
approved service agent and only l Remove all elements of the
packaging.
genuine spare parts should be
fitted. Any failure to follow the
above advice may have serious
WARNING:
consequences for the safety of
Keep packaging materials
the appliance.
away from children.
l If it you need to move the
machine after removing the l Do not install or use the
packaging, do not try to lift it by
dishwasher if it is damaged.
the bottom of the door. Open
the door slightly and lift the l Follow the instructions supplied
machine by holding on the top.
with the product.
5
EN
l If
2. WATER CONNECTION
l If the dishwasher is connected to new pipes
The appliance must be connected to
the water mains using new hose-sets.
The old hose-sets should not be
reused.
or to pipes which have not been inuse for a
long time run water through for a few
minutes before connecting the inlet hose. In
this way no deposits of sand or rust will
clog up the water inflow filter.
l The inlet and drain hoses can be directed
to left or right.
1
The dishwasher can be connected to
either cold or hot water, as long as it
is no hotter than 60°C.
B
l Water pressure must be between 0,08
MPa and 0,8 MPa.
l The inlet hose must be connected to a tap
so that the water supply can be cut off
when the machine is not in use (fig. 1 B).
2
l The dishwasher is fitted with 3/4" threaded
connector (fig. 2).
B
l Connect inlet hose "A" to water tap "B"
with a 3/4" attachment making sure that it
has been properly tightened.
A
l If it is necessary, the inlet pipe can be
lengthened up to 2,5 m. The extension
pipe is available from the After Sales
Service Centre.
6
A device located on the supply tube that
stops water flow if the tube deteriorates;
in this case, a red mark will appear in the
window "A" and the tube must be
replaced. To unscrew the nut, press the
one-way lock device "B".
All the dishwashers are equipped with
an overflow safety device which, if
water exceeds normal levels due to
malfunctions, automatically blocks
water flow and/or drains excess
quantities.
4
SOME MODELS may include one or more
of the following features:
B
l WATERBLOCK (fig. 3)
A
The waterblock system has been designed to
improve the safety of your appliance. The
system prevents flooding which might be
caused by a machine malfunction or as a
result of a fracture on the rubber pipes
and in particular on the water supply pipe.
l AQUAPROTECT - SUPPLY TUBE WITH
GUARD (fig. 5):
Should water leak from the primary internal
tube "A", the transparent containment
sheath "B" will contain water to permit
the washing cycle to complete. At the
end of the cycle, contact the Customer
Service Centre to replace the supply
tube.
How it works
A sump located on the base of the appliance
collects any possible water leakage and
operates a sensor which activates a valve
placed under the water tap and blocks any
water, even with the tap fully opened.
If box "A" containing the electrical parts is
damaged, remove the plug from the socket
immediately. To ensure perfect operation of
the safety system, the hose with box "A"
should be connected to the tap as shown in
the figure. The water supply hose should
not be cut, as it contains live parts. If the
hose is not long enough for correct
connection, it must be replaced with a longer
one. The hose can be obtained from the
Technical Assistance Centre.
3
5
B
A
A
7
EN
l AQUASTOP (fig. 4):
Hydraulic safety devices
Connecting the outlet hose
l The outlet hose should disharge into a
l The hose can be hooked over the side of
standpipe, making sure that there are no
kinks (fig. 6).
the sink, but it must not be immersed in
water, in order to prevent water from
being syphoned back to the machine
when this is in operation (fig. 6Y).
l The standpipe must be at least 40 cm
above floor level and it must have an
internal diameter of at least 4 cm.
l When installing
the appliance under a
worktop the hose pipe clamp must be
attached to the wall in the highest
possible position under the worktop
(fig. 6Z).
l It is advisable to fit an anti-odour air trap
(fig. 6X). If necessary the outlet hose can
be extended up to 2,5 m, provided that it
is kept at a maximum height of 85 cm
above floor level. The extension pipe is
available from the After Sales Service
Centre.
l Check that there are no kinks in the inlet
and outlet hoses.
6
Y
X
Z
8
After loading the salt, YOU MUST run
a complete washing cycle, or the
PRE-WASH/COLD
RINSE/REFRESH
programme.
(Fig. A "1")
l The appearance of white stains on dishes
is generally a warning sign that the salt
container needs filling.
l The salt dispenser has a capacity of
between 1.5 and 1.8 kg and, for efficient
use of the appliance, it should be refilled
from time to time .
l On the bottom of the machine there is a
container for the salt for regenerating the
softener.
l It is important to use only a salt that is
(Only for first start up) When the
appliance is used for the first time,
after completely filling the salt
container, it is necessary to add water
until the container overflows.
specifically designed for dishwasher.
Other types of salt contain small
quantities of insoluble particles which
over a long period of time may affect and
deteriorate the softener performance.
l To add salt, unscrew the cap of the
container on the bottom and then refill the
container.
l During this operation a little water will
overflow; but keep adding salt until the
container is full. When the container is
full, clean the thread of salt residue and
retighten the tap.
l After loading the salt, it is recommended
running a complete washing cycle, or
COLD RINSE programme.
9
EN
3. LOADING THE SALT
4. ADJUSTING THE UPPER Type "B": (ONLY MODELS WITH EASY CLICK):
BASKET (SAME MODELS 1. Remove the upper basket;
2. Hold the basket on both sides and lift it
ONLY)
upwards (fig. 1).
l If 29 cm to 32.5 cm plates are regularly
used, load them onto the lower basket
after the upper basket has been placed in
its upper position, as detailed below
(according to the model):
Type "A":
1. Turn front blocks "A" outwards;
2. Remove the basket and remount it in
the upper position;
3. Replace blocks "A" in the original
position.
Dishes that are greater than 20 cm in
diameter can no longer be loaded onto the
upper basket, and the mobile supports
cannot be used when the basket is in the
upper position.
Type "A"
Dishes that are greater than 20 cm* in
diameter can no longer be loaded onto the
upper basket, and the mobile supports
cannot be used when the basket is in the
upper position.
* In models fitted with a third basket, dishes
measuring more than 14 cm in diameter
can no longer be loaded onto the upper basket.
ADJUSTING THE BASKET
LOWER POSITION:
TO
THE
1. Hold the basket on both sides and lift it
gently upwards (fig. 1);
2. Then slowly release into the correct
position (fig. 2).
N.B.: NEVER LIFT OR LOWER THE
BASKET FROM ONE SIDE ONLY (fig. 3).
WARNING:
We recommend adjusting the basket before
loading the dishes.
Type "B"
1
A
2
a
b
a
b
A
3
10
example of loading see fig. 1, 2 e 3.
Using the upper basket
Upper basket (fig. 1)
l The upper basket is provided with mobile
racks hooked to the sides of the basket,
which can be regulated into 4 positions.
l In the lowered position (A-A1) the racks
may be used for such items as: tea and
coffee cups, kitchen knives and ladles.
Also glasses with stems may be safely
hung on the ends of the racks.
Upper basket (fig. 2)
l In the upright position (B-B1) the racks
allow you to load dinner plates and soup
plates. Plates should be loaded vertically
with the underside of the plate towards
the back of the dishwasher with a space
between each plate to allow water to pass
freely.
Upper basket (fig. 3)
l It is advisable to load large plates
(approx. 26 or more cm) slightly tilted
towards the rear to facilitate introduction
of the basket into the machine.
l Salad bowls and plastic bowls may also
be loaded on the upper basket. It is
advisable to block these in place so that
the jets of water do not make them
overturn.
Using the lower basket
l The upper basket has been designed to
l Saucepans, oven dishes, tureens, salad
offer maximum flexibility in use and can
be loaded with up to 24 plates on two
rows, up to 30 glasses on five rows or a
mixed load.
bowls, lids, serving dishes, dinner plates,
soup plates and ladles can be loaded on
the lower basket.
11
EN
5. LOADING DISHES
l Place the cutlery in the plastic cutlery
holder with the handles pointing upwards.
l Place the cutlery holder on the lower
basket (fig. 4 and 5), making sure that
the cutlery does not get in the way of the
rotating arms.
Cutlery basket (fig. 6)
The cutlery basket is made with two
detachable parts which will enable various
loading options. The two parts can be
detached by sliding the left section away
from the right section. The top of cutlery
basket can be removed, for enable various
loading options.
The lower basket has a safety-stop
device, for its safe extraction, also
especially useful with a full load. For
loading salt, cleaning filter and for
ordinary maintenance, the complete
extraction of the basket is necessary.
Please load the dishwasher sensibly to
ensure the best wash results.
example of loading see. fig. 4 e 5
Lower basket (fig. 4)
6. INFORMATION FOR
TEST LABORATORIES
Please ask information required for
comparison testing and measuring noise
levels, according to EN normative, to the
following address:
testinfo-dishwasher@candy.it
In the request, please specify model name
and number of the dishwasher (see rating
plate).
Lower basket (fig. 5)
12
EN
7. LOADING THE
DETERGENT
(Fig. A "2")
The detergent
It is essential to use a detergent that is
specifically designed for dishwashers
either in powder, liquid,gel or tablet form.
After pouring the detergent into the
container, close the lid, firstly pushing (1)
and then pressing on it (2) until you hear
the click.
Unsuitable detergents (like those for
washing up by hand) do not contain the
proper ingredients for use in a dishwasher,
and stop the dishwasher from working
correctly.
Filling the detergent container
The detergent container is inside the door
(fig. A "2"). If the lid of the container is
closed, press the button (A) to open. At the
end of every wash cycle the lid is always
open and ready for the next time the
dishwasher is used.
Since not all detergents are the same the
instructions on the boxes of detergent can
vary. We should just like to remind users
that too little detergent does not clean the
dishes properly whilst too much detergent
will not produce better results and is also a
waste.
Do not use an excessive amount of
detergent and help limit damage to the
environment at the same time.
WARNING
When loading the lower basket, please
ensure that the plates or others do not
obstruct the detergent dispenser.
The amount of detergent to be used varies
according to how dirty the dishes are and
on the type of dishes to be washed. We
advise using 20:30 g of detergent in the
wash section of detergent compartment (B).
13
8. TYPES OF DETERGENT
l read carefully and follow the manufacturer’s
Detergent tablets
l the
Detergent tablets of different manufacturers
dissolve at different speeds, for this reason,
during short programmes, some detergent
tablets may be not fully effective, because
they are not completely dissolved. If these
products are used, is recommended to
choose longer programmes to guarantee
the complete use of the detergent.
If when using this type of product, you
don't get satisfactory washing results,
please contact the detergent manufacturer.
instructions given on the packaging;
effectiveness
of
detergents
containingthe built in water softener/salt
depends on the hardness of your water
supply. Check that the hardness of your
water supply is within the effective range
given on the detergent packaging.
In certain circumstances use of combined
detergents can cause:
To get satisfactory washing results,
the tablets MUST be placed in the
wash section of the detergent
container and NOT directly in the tub.
l limescale deposits on dishes or in the
dishwasher;
l a reduction in washing and drying
performance.
Concentrated detergents
The concentrated detergents, with reduced
alkalinity and with natural enzymes, in
conjunction with 50°C wash programmes,
have a smaller impact on the environment
and they protect the dishes and the
dishwasher. The 50°C wash programmes
purposely
exploit
the
dirt-dissolving
properties of the enzymes, allowing
therefore, with the use of the concentrated
detergents, to achieve the same results of
the 65°C programmes but at a lower
temperature.
Combined detergents
The detergents that also contain the rinse
aid must be placed in the wash section of
the detergent container. The rinse aid
container must be empty (if it is not empty,
set the rinse aid regulator to lowest position
before using combined detergents).
Any problems which arise as a direct
result of the use of these products are not
covered by our warranty.
Please note that using the "TABS"
combined detergents, the rinse aid and
salt indicator lights (only used on
selected models) are superfluous, so
you must ignore the lights.
If washing and/or drying problems occur,
we recommend you return to use traditional
separate products (salt, detergent and rinse
agent). This will ensure that the water
softener in the dishwasher operates
correctly.
In this case, we recommends that you:
l refill both the salt and rinse aid container;
l run one normal washing cycle without a
"TABS" combined detergents
load.
If you are planning to use "TABS" (“3 in
1 “/ “4 in 1”/ “5 in 1”, etc.) combined
detergents i.e. those with built in salt and/or
rinse agent, we would advise the following:
14
Please note that on return to the use of
conventional salt, a number of cycles will be
required before the system becomes fully
efficient again.
9. LOADING THE RINSE AID
EN
(Fig. A "3")
The rinse aid
The rinse aid, which is automatically
released during the last rinsing cycle, helps
the dishes to dry quickly and prevents spots
and stains forming.
Filling the rinse aid container.
The rinse aid container can be found to the
left of the detergent container (fig. A "3").
To open the lid, push the reference mark
and, in the same time, pull the tab of
opening. It is always advisable to use rinse
aid that is specifically designed for
dishwasher. Check the rinse aid level
through the indicator eye (C) which is
located on the dispenser.
FULL
EMPTY
dark
light
Regulating the rinse aid from
1 to 6
The regulator (D) is placed under the lid
and can be turned using a coin. The
recommended position is 4.
The limestone content of the water
considerably affects the formation of
limescale and the drying performance.
It is therefore important to regulate the
quantity of rinse aid to achieve good
washing results.
If, after the wash, streaks occur on the
dishes, decrease the amount by one
position. If whitish spots occur, increase the
amount by one position.
15
10. CLEANING THE FILTERS
(Fig. A "4")
The filter system consists of:
A. A central container that traps the larger
particles;
B. A micro filter, located beneath the
gauze, that traps the tiniest particles
ensuring a perfect rinse;
C. A flat gauze that continuously filters the
wash water.
l To achieve excellent results every time,
the filters should be checked and cleaned
after each wash.
l To remove the filter unit, simply turn the
handle anticlockwise (fig. 1).
l For
ease of cleaning, the
container is removable (fig. 2).
central
l Remove the gauze filter (fig.3) and wash
the whole unit under a jet of water. If
necessary a small brush can be used.
l With the Self-cleaning Micro filter,
maintenance is reduced and the filter unit
need only be checked every two weeks.
Nevertheless, after each wash it is advisable
to check that the central container and the
gauze filter are not clogged.
WARNING
After cleaning the filters, make sure that
they are correctly reassembled and
that the gauze filter is properly
positioned at the bottom of the
dishwasher. Make sure that the filter
is screwed back, clockwise, into the
gauze, as poor seating of the filter unit
could have an adverse effect on the
efficiency of the appliance.
Never use the dishwasher without the
filters.
16
How to get really good wash
results.
l Before
placing the dishes in the
dishwasher, remove any remaining food
(bones, shells, pieces of meat or
vegetables, coffee grounds, skin of fruit,
cigarette ash, thooth picks etc. to avoid
blocking the filters, water outlet and
washing arm nozzles.
l If the dishes are not very dirty or if the
baskets are not very full select an
ECONOMY programme, following the
instructions in the program list.
What not to wash.
l Try not to rinse the dishes before loading
l It should be remembered that not all
them into the dishwasher.
dishes are suitable for washing in a
dishwasher. We advise against using the
dishwasher
to
wash
items
in
thermoplastic, cutlery with wooden or
plastic handles, saucepans with wooden
handles, items in aluminum, crystal
leaded glass unless otherwise stated.
l If saucepans and oven dishes are
encrusted with the remains of burnt or
roast food, it is advisable to leave them to
soak before washing.
l Place the dishes face downwards.
l Try to place the dishes in such a way that
l Certain decorations may fade. It is
they are not touching one another. If they
are loaded properly you will get better
results.
therefore a good idea before loading the
whole batch to wash just one of the items
first so as to be sure that others like it will
not fade.
l After loading the dishes check that the
washing arms can rotate freely.
l It is a good idea not to put silver cutlery
with non-stainless steel handles into the
dishwasher as there could be a chemical
reaction between them.
l Pans
and other dishes that have
particularly stubborn food particles or
remnants of burnt food should be left to
soak in water with dishwasher detergent.
When buying new crockery or cutlery
always make sure that they are
suitable for washing in a dishwasher.
l To wash silver properly:
a) rinse the silver immediately after use,
especially if it has been used for
mayonnaise, eggs, fish etc.;
b) do not sprinkle detergent onto it;
Useful hints
c) keep it separate from other metals.
l In order to avoid any dripping from the top
rack, remove the lower rack first.
How to make savings.
l If you want the dishwasher to give a
l If the dishes are to be left in the machine
complete wash, place the dishes in the
dishwasher at the end of each meal and if
necessary turn on the COLD RINSE cycle
for some time, leave the door ajar, to let
some air circulate and to improve the
drying performance.
17
EN
to soften the food remains and remove
bigger particles of food from the new load
of dishes. When the dishwasher is full
start
the
complete
wash
cycle
programme.
11. PRACTICAL HINTS
12. CLEANING AND
MAINTENANCE
Do not use tools that can deform the
spray heads.
(Fig. A “5”)
l To clean the dishwasher outside, do not
use solvents (degreasing action) neither
abrasives, but only a cloth soaked with
water.
l The dishwasher does not require special
maintenance, because the tank is selfcleaning.
3) when you have finished, refit the rotor
arms
in
the
same
position,
remembering to re-align the arrow and
screw into position.
l Both the door lining and the tank lining
are in stainless steel; however, should
spots caused by oxidation occur, this is
probably due to a high level of iron salts
presents in the water.
l Regularly wipe the door gasket with a
damp cloth to remove any food remains
or rinse aid.
l Dishwasher cleaning is recommended, in
order to remove limestone deposits or
dirt. We suggest you run a washing cycle
periodically with specialist dishwasher
cleaning products. For all cleaning
operations the dishwasher must be
empty.
l The spots can be removed with a mild
abrasive agent; never use chlorine based
materials, steel wool, etc.
1
1b
l If, in spite of the routine cleaning of the
filters, you notice that the dishes or pans
are not properly washed or rinsed, check
that all the spray heads on the rotor arms
(fig. A “5”) are clear.
If they are blocked, clean them in the
following way:
1) to remove the upper rotor arm, turn it
until it lines up with the stop marked by
the arrow (fig. 1b). Push it upwards
(fig. 1) and, keeping it pushed in,
unscrew it in a clockwise direction (to
reassemble it repeat the same
operation, but turn it anticlockwise).
The lower rotor arm can be removed
simply by pulling it upwards (fig. 2);
2) wash the rotor arms under a jet of water
to clear any blockage in the spray
heads.
18
2
WHEN CYCLE IS FINISHED.
After every wash it is essential to turn off
water supply and to switch off the machine
by pressing the On/Off button to the off
position.
If the machine is not going to be used for
some time, it is advisable to follow these
rules:
4. fill the rinse aid container;
6. keep the inside of the machine clean;
1. do an empty wash with detergent in
order to clean the machine of any
deposits;
7. If the machine is left in places where the
temperature is below 0°C any water left
inside the pipes may freeze. Wait until
the temperature rises above zero and
then wait for about 24 hours before.
2. pull out the electric plug;
3. turn off the water tap;
19
EN
5. Ieave the door ajar;
L "PROGRAMME SELECTION" light
M "Addish" light
D "EXPRESS" option button
E "START DELAY" button
20
Fuse / Power input / Supply voltage
Water supply pressure (MPa)
Capacity with pans and dishes
Place settings (EN 50242)
120
117
59,8x82x58
WITHOUT
WORKTOP
13
8 people
See rating plate
Min. 0,08 – Max. 0,8
9 people
15
117
59,8x81,8 ÷ 89,8x57
HALF-INTEGRATED
TECHNICAL DATA (See rating plate)
60x85x60.9
Depth with door open (cm)
WITH
WORKTOP
Width x Height x Depth (cm)
DATA
FREE-STANDING
9 people
16
117
59,8x81,8 ÷ 89,8x55
FULL-INTEGRATED
BUILT-IN
I "DELAY START" time lights
C "Start/Reset" button (start/cancel programme)
SIZE
H "PROGRAMME STATUS" lights/"DELAY START" time lights
B "PROGRAMME SELECTION" button/ENROLMENT Wi-Fi
F "Reset" button for "SALT EMPTY" light
G "RINSE AID EMPTY" light
A ON/OFF Button
13. DESCRIPTION OF THE
CONTROL PANEL
14. TECHNICAL DATA
Next time you switch on the
appliance
l Open the door.
l Hold down the ON/OFF button for about
ON/OFF button
l To turn the appliance on and off, press
3 sec. to turn the machine on, and the
“P3”programme indicator light will come on.
the ON/OFF button (for at least 3
seconds).
If you have turned on the programme
memorisation function, the indicator
light corresponding to the last
programme completed will appear on
the display.
At the end of the cycle, remember to
switch off the appliance using the
ON/OFF button, then remove the plug
and close the water supply.
Settings Menu
First time you switch on the
appliance
From the Settings menu, you can adjust
various parameters to suit your washing
requirements.
l Connect the machine to the power
supply.
Entering the Settings menu
l Open the door, put the dishes to be
washed inside, and close the door again.
l Open the door.
l Turn on the dishwasher by holding the
l Press the "ON/OFF" button and hold for
“ON/OFF” button down for about 3 sec.
about 3 seconds.
l Hold down the “Progr.” and “ON/OFF”
buttons for about 5 sec.
l At this time only the “ON/OFF” and
l All the indicator lights will flash for 5 sec.
”Progr.” buttons will be active, and all the
programme indicator lights will come on
for 3 sec. After this only indicator light
“P3” will stay on, and all the buttons will
still be active.
l The settings will be displayed:
- Lime scale prevention settings appear
when the indicator light comes on in the
corresponding programmes. If they are
all off, the level is set to "S0".
l Choose
a
programme
with
the
"PROGRAMME SELECTION" button.
- When the audio signal is activated, the
"Express" indicator light comes on.
l If you wish to select an option, press the
- When the “Memo” function is activated,
the "6h" indicator light on the start
delay function comes on.
corresponding button (the indicator light
representing the selected option will
come on).
l When you press the "Progr." button,
l Press "Start/Reset" and a signal will
adjustment of SOFTENER will begin
(refer to the appropriate chapter in the
instruction booklet for information).
sound, the indicator light corresponding to
the selected programme will stay on and
the wash indicator light will come on.
l Press the "Express" button to turn on
l Close the door (after an audible signal
adjustment of the BUZZER. (refer to the
section on this topic for information on
how to adjust).
has sounded, the programme will start
automatically).
21
EN
15. PROGRAMME SELECTION
AND SPECIAL FEATURES
l Press the "Start Delay" button to activate
the MEMO FUNCTION (refer to the
appropriate chapter in the instruction
booklet for information on how to turn it
on and off).
Adding dishes after the ADDISH
indicator light has switched off is
strongly discouraged as this could
affect the wash performance.
"AUTOMATIC" programmes
(only on some models)
The dishwasher is equipped with a dirt sensor,
capable of analysing water murkiness during all
"AUTOMATIC" programme phases (see
programme legend). Thanks to this device,
the wash cycle parameters are automatically
adapted to the real quantity of dirt on dishes.
This is because water murkiness is linked to the
quantity of dirt on dishes. Thus, excellent
washing results are guaranteed while
optimising water and energy consumption.
"IMPULSE" programmes
(only on some models)
The "IMPULSE" programmes use an
impulse washing technology, which reduces
consumption and noise, and improves
performance.
The “intermittent” working of the
washing pump is NOT to be
considered a malfunction; it is a
characteristic of impulse washing,
and therefore should be considered a
normal feature of the programme.
WARNING
If you open the door during the drying
cycle, an intermittent audio signal
advises you that the drying cycle has
not yet finished.
Programme interruption
Opening the door when a programme is
running is not recommended especially
during the main wash and final hot rinse
phases. However, if the door is opened
while a programme is running (for example,
to add dishes) the machine stops
automatically. Close the door, without
pressing any buttons. The cycle will start
from where it left off.
WARNING:
If you open the door during the drying
cycle, an intermittent audio signal
advises you that the drying cycle has
not yet finished.
ADDISH (possibility of adding dishes
after the programme has started)
Changing a running programme.
When the programme starts, you should
only open the door and add more dishes
when the ADDISH
indicator light is
switched on. The appliance will stop
automatically and the time remaining to the
end of the cycle will flash on the display. Close
the door, without pressing any buttons.
The cycle will start from where it left off. When
the relating indicator light switches off, it is no
longer advisable to add further dishes.
22
Open the door slowly and carefully, to
avoid getting wet with splashes of
washing water.
Proceed as follows to change or cancel a
running program:
l Open the door.
l Hold the "Start/Reset" button down for at
least 3 seconds.
l Some audible signals will sound and the
programme indicator lights will turn on
and off individually and sequentially.
If an option is selected that is not
compatible with the selected programme
then the option indicator light first flashes
and then goes off.
and all the programme indicator lights will flash.
l At this point a new programme can be set.
WARNING:
"Express" button
This button enables average energy and
time savings of 25% (according to the cycle
selected), reducing the wash water
temperature and the drying time during the
final rinse. This option is recommended for
evening washing when perfectly dry dishes
are not needed immediately.
For better drying, leave the dishwasher
door slightly ajar to promote natural air
circulation in the dishwasher.
Before starting a new programme, you
should check that there is still detergent
in the dispenser. If necessary, top up the
dispenser.
Programme operations.
When a programme is running the relevant
indicator light will remain on and the 3
"PROGRAMME STATUS" indicator lights:
WASH
"NO SALT" indicator light
RINSE
This model is provided with an indicator
light on the control panel that lights up when
the salt needs to be topped up. The
appearance of whitish stains on dishes is
generally a warning sign that the salt
container needs filling.
DRY
will light singularly and in sequence to
indicate the current phase.
If there is any break in the power supply
while the dishwasher is operating, a
special memory stores the selected
programme and, when the power is
restored, it continues where it left off.
"RESET" button for "NO SALT"
indicator light
Programme end
After filling the salt container, you should
press this button for a few seconds, until the
corresponding indicator light switches off.
A 5 second buzzer will sound (if not muted)
3 times at 30 second intervals to signal that
the programme has ended.
Option buttons
WARNING:
If you press the reset button without
filling the salt container, this will
interfere with the correct functioning of
the salt indicator light.
The option buttons provide you with further
wash options, allowing you to customise the
wash programmes (see the table in chapter
17 for a list of programmes on which each
option can be enabled). Options are
enabled (or disabled) before starting the
programme, using the appropriate buttons.
The relevant indicator lights will appear (or
disappear) on the display. The option button
should be enabled after you have chosen
the wash programme.
In order to guarantee the correct
functioning of the salt indicator light,
YOU MUST ALWAYS FULLY REPLENISH
THE SALT CONTAINER.
23
EN
l The running programme will be cancelled
"START DELAY" button
The dishwasher start time can be set with
this button, delaying the start by 3, 6 or 9
hours.
Proceed as follows to set a delayed start:
l Turn on the dishwasher by pressing the
l Choose a programme by pressing the
"PROGRAMME SELECTION" button.
"ON/OFF" button for about 3 sec.
l Hold down the "Progr." and "ON/OFF"
l Press the "START DELAY" button (each
time the button is pressed the start will be
delayed by 3, 6 or 9 hours respectively,
and the corresponding time indicator light
will switch on).
l To start the countdown, press the
time
buttons for about 5 sec.
l All the indicator lights will flash for 5 sec.
- If the audio signal is active, the
"Express" indicator light will be on.
- If the audio signal is not active, the
"Express" indicator light will be off.
1. Press the "Express" button to turn the
audio signal on or off.
If a 9 hour delay is set, countdown will be
displayed by the 6h indicator light after 3
hours and the 3h indicator light after 6
hours.
At the end of the last 3 hours (at the end of
countdown) the 3h indicator light will stop
flashing and remain on to indicate the
washing phase and the programme will
start automatically.
If countdown has not ended, whereby the
programme has not yet started, it is
possible to change or cancel the delayed
start and select another programme or to
select/deselect
the
option
button,
proceeding as follows:
l Hold the "Start/Reset" button down for at
least 3 seconds. Some audible signals
will sound and the programme indicator
lights will turn on and off individually and
sequentially.
l The delayed start and the selected
programme will be cancelled. The
programme indicator lights will flash, the
dishwasher is ready start Programme.
24
You can deactivate turning on and off of the
audio signal as follows (the default setting is
active):
l Open the door.
l Open the door.
"Start/Reset" button (the set
indicator light will start to flash).
Activation/Muted END-OFPROGRAMME signal.
2. Whenever the audio signal is turned on,
in addition to visual confirmation given by
turning on the "Express" led, an acoustic
signal will sound as confirmation.
3. If you turn off the audio signal, no audio
signal will sound to accompany the
visual confirmation when the "Express"
led goes off.
4. Turn off the dishwasher by holding down
the "ON/OFF" button for about 3 sec. to
make the new setting effective.
MEMO FUNCTION (Memorising
the last programme used)
Proceed as follows to enable storage of the
last programme used in memory:
l Open the door.
l Turn on the dishwasher by pressing the
"ON/OFF" button for about 3 sec.
l Hold down the "Progr." and "ON/OFF"
buttons for about 5 sec.
l All the indicator lights will flash for 5 sec.
3. Turn off the dishwasher by holding down
the "ON/OFF" button for about 5 sec. to
make the new setting effective.
2. When you press the "Start Delay"
button, the "6h" indicator light will come
on and an audio signal will sound.
Follow the same procedure to turn off the
memory.
25
EN
1. The "6h" indicator light on the "Start
Delay" function is off by default.
16. REMOTE CONTROL (WI-FI)
Successful enrollment
This appliance is equipped with Wi-Fi
technology that allows the machine to be
remote controlled via an app.
l The 3h-6h-9h indicator lights will go off,
l The machine is connected, and you can
Pairing the machine with the app
now control your machine from the app.
l Download the Candy simply-Fi app onto
your device.
l The 3h-6h-9h and P3 P4 indicator lights
will go out.
l The machine will not be connected.
To discover all the details of the Wi-Fi
features, explore the app menus in
DEMO mode.
l Repeat the enrollment procedure, holding
down the "START DELAY" button again.
l Make sure the router is turned on and
your smartphone/tablet is connected to
your home Wi Fi network.
on
BLUETOOTH
on
smartphone/tablet (if available).
For more information, refer to the
"Enrollment App - Quick Guide" that
comes with your machine, also accessible
at the link : go.candy-group.com/bm-dw
your
Resetting the WiFi
l Open the app, create a user profile and
enroll the appliance, following the
instructions appearing on the device’s
display
l Turn on the dishwasher with the ON/OFF
button when instructed to do so in the
app.
l Press "Progr. 3sec WiFi" and hold down
for 3 sec.; à indicator lights P3 and P4 will
both flash.
l Press the "START DELAY" button and
hold down for 3 sec. within 60 sec. of the
previous step; the 3h-6h-9h indicator
lights will all flash simultaneously for 5
min.
l Enter the password of your home WiFi
network in the app and complete the
procedure.
26
Unsuccessful enrollment
If enrollment fails, or does not succeed
within 5 min.:
The Candy simply-Fi app is available
both for Android and for iOS tablets
and smartphones.
l Turn
while the P3 P4 indicator lights will stay
on.
Repeat the enrollment procedure in the
event of problems or a change in your
home router password.
ENABLING REMOTE CONTROL
Whenever you want to use the machine
with remote control:
l Fill the dishwasher, add detergent, and
close the door.
l Turn on the dishwasher.
l Press "Progr. 3sec WiFi" and hold down
for 3 sec. à; the P3 P4 indicator lights
will come on steady.
l You may now use the app and remote
control the machine with your device.
Alternative way to exit remote control.
DISABLING REMOTE CONTROL
sec.: if there is a cycle under way, it will
be cancelled, and the machine will exit
REMOTE CONTROL mode. You may
now set a new wash cycle using the
control panel.
3sec WiFi” for 3 sec.
l When no cycle is under way:
Indicator lights P3 P4 will go off and the
led corresponding to the last programme
the machine completed (or P3) will come
on.
If you turn the machine off and turn it
back on with the On/Off button while
REMOTE CONTROL is enabled and a
cycle is under way (or if the power
supply is interrupted), the cycle will
resume from the point at which it was
interrupted. "REMOTE CONTROL" will
be disabled and indicator lights P3
and P4 will flash.
l When a cycle is under way:
Indicator lights P3 P4 will start flashing,
while the programme phase indicator
lights will show the point in the washing
cycle that the machine has reached.
The cycle will be completed without
control from the app.
27
EN
l Press "Start/Reset" and hold down for 3
l To exit remote control, press “Progr.
17. PROGRAMME LEGEND
Programme
Description
P1
Intensive
Once a day - for heavily soiled pans and any other
items that have been left all day for washing.
P2
Universal
Once a day - for normal soiled pans and any other
items that have been left all day for washing.
P3
Eco
Programme for normally soiled tableware (the
most efficient in terms of its combined energy and
water consumption for that type of tableware).
Programme standardised to EN 50242.
P4
Prewash
Short cold prewash for items that are stored in the
dishwasher until you are ready to wash a full load.
P5
Programme suitable for washing in a single cycle
the most delicate dishes such as glassware and
porcelain in Washing Class A.
Programmes with prewash
For wash programmes with prewash, it is advisable to add a second dose of detergent (max.10 g)
directly in the machine.
28
"IMPULSE" programmes
Temperature of wash (°C)
Average time of
wash ¹ (min.)
"START DELAY" Button
"Express" Button
P1
Intensive
●
-
75
130
YES
YES
P2
Universal
-
■
60
120
YES
YES
P3
Eco
●
■
45
190
YES
YES
P4
Prewash
-
-
-
5
YES
N/A
●
■
60
39
YES
YES
Programme
P5
● = Add detergent for prewash
■ = "IMPULSE" Programmes (only on some models)
N/A= OPTION NOT AVAILABLE
1) With cold water (15°C) – Tollerance ±10% With hot water the time remaining until the end of the programme is automatically displayed while
the programme is running. *Values are measured in a laboratory according to European Standard EN 50242 (consumption
may vary according to conditions of usage). 29
EN
Detergent for soaking
(Prewash)
Options
18. WATER SOFTENER UNIT
Depending on the source of the supply,
water contains varying amounts of
limestone and minerals which are deposited
on the dishes leaving whitish stains and
marks. The higher the level of these
minerals present in the water, the harder
the water is.
The dishwasher is fitted with a water
softener unit which, through the use of
special regenerating salt, supplies softened
water for washing the dishes. The degree of
hardness of your water can be obtained
from your water supply company.
According to the degree of hardness of your
water, regulate the softener unit in the
following way:
The dishwasher must ALWAYS be off
before start of this procedure.
1. Turn on the dishwasher by pressing the
"ON/OFF" button.
2. Press the "Progr." and "ON/OFF"
buttons at the same time, and hold for 5
sec.
Programme
Indicator Light
4. The "PROGRAMME SELECTION"
indicator lights will come on to show
lime scale remover levels. If no indicator
lights come on, level "S0" will be set.
Use of
Regenerating salt
Hardness of up to 90°fH (French grading) or
50°dH (German grading) through 6 different
settings. The table below lists different
degrees of water hardness with the
corresponding setting for the softener unit.
ºdH
(German
grading)
3. A short audio signal will sound and all
the indicator lights will flash for 5 sec.
ºfH
(French
grading)
Regulating the water softener
S0
0-5
0-3
NO
No indicator
lights
S1
6-15
4-9
YES
P1
S2
16-30
10-16
YES
P1+P2
*S3
31-45
17-25
YES
P1+P2+P3
S4
46-60
26-33
YES
S5
61-90
34-50
YES
Level
Water
hardness
5. Press "Progr." again to select the
desired level of lime scale removal:
every time you press the button, the
corresponding indicator light will come
on, as shown in the table above
(P1àS1, P2àS2,...) For level "S0", all
the lights will be out.
6. Turn off the dishwasher by holding
down the "ON/OFF" button for 3 sec.
to make the new setting effective.
WARNING!
If any problem occurs, turn the
dishwasher off by pressing the "ON/OFF"
button and start the procedure again
from the beginning (STEP 1).
P1+P2+P3+
P4
P1+P2+P3+
P4+P5
* The water softener unit is set in the
factory at level 3, as this is suitable for
the majority of users.
30
If you believe the dishwasher is not working correctly, consult the quick guide provided
below with some practical tips on how to fix the most common problems. If the
malfunction continues or recurs, contact the Technical Assistance Centre.
BUG REPORTS
l Models with a display: errors are reported by a number preceded by the letter "E"
(e.g. Error 2 = E2) and a short audio signal.
l Models without a display: errors are reported by the indicator lights flashing on the
control panel.
Only models with a display
Error displayed
"CHECK WATER"
with a short audio signal
(only on some models).
E2 (with display) with a
short audio signal
E3 (with display) with a
short audio signal
E4 (with display) with a
short audio signal
Meaning and solutions
The dishwasher does not fill with water
Make sure the water supply is open.
Make sure the water supply hose is not bent or crushed.
Make sure the drain pipe is at the proper height (see installation
section).
Close the water supply, unscrew the drain pipe from the back of the
dishwasher and check that the "sand" filter is not clogged.
The dishwasher does not drain water
Make sure the drain pipe isn’t bent, trapped or blocked, and the filter
is not clogged.
Make sure the siphon is not clogged.
Water leak
Make sure the drain pipe isn’t bent, trapped or blocked, and the filter
is not clogged.
Make sure the siphon is not clogged.
E4-E6-E7-Ef-EL
Electronic control fault.
(with display) with a
short audio signal
Contact the Technical Assistance Centre.
E8-Ei
(with display)
with a short audio signal
The water heating element is not working correctly or the filter
plate is clogged
Clean the filter plate.
Only models without a display
If malfunctions or faults occur when a programme is running, the indicator light that
corresponds to the selected cycle will blink rapidly, and an intermittent audio signal will
sound. In this case, turn the dishwasher off by pressing the "ON/OFF" button.
After checking to make sure the water supply is open, that the drain pipe is not bent
and that the siphon or filters are not clogged, set the selected program again.
If the fault persists, contact the Technical Assistance Centre.
31
EN
19. TROUBLESHOOTING AND WARRANTY
This dishwasher is equipped with an overflow safety device that, in the event of a
problem, automatically discharges any excess water.
WARNING
To ensure the correct operation of the overflow safety
device, we recommend not moving or tilting the dishwasher
during operation. Should it be necessary to tilt or move the
dishwasher, please ensure that the washing cycle is
complete and that no water remains inside the appliance.
Other faults
FAULTS
1. No programme
works
2. Dishwasher
does not fill
with water
3. Dishwasher
does not
discharge water
4. Dishwasher
discharges
water
continuously
5. Spray arms are
not heard to
rotate
CAUSE
SOLUTION
Plug not connected to wall socket
Connect electric plug
O/I button not pressed
Press button
Door is open
Close door
No electricity
Check
See point 1
The water tap is closed
The water supply hose is bent
Check
The filter of the water supply
hose is clogged
Clean the filter at the end of the
hose
Filter is dirty
Clean filter
Drain pipe is bent
The drain pipe extension is not
correctly connected
The outlet connection on the
wall is pointing downwards not
upwards
Eliminate the bends in the pipe
Follow the instructions for connecting
the drain pipe carefully
Position of the drain pipe is too
low
Lift drain pipe to at least 40 cm
above floor level
Excessive amount of detergent
Item prevents arms from rotating
Filtering plate and filter very dirty
32
Open the water tap
Eliminate the bends in the hose
Call a qualified technician
Reduce amount of detergent Use
suitable detergent
Check
Clean filtering plate and filter
6. On electronic
appliances
without a
display: one or
more indicator
lights flashing
quickly
CAUSE
SOLUTION
EN
FAULTS
Water supply tap turned off
Switch off the appliance. Turn on the
tap. Re-set the cycle.
See point 5
Check
Bottom of saucepans have not
been washed well
Burnt on food remains must be
soaked before putting pans in
dishwasher
Edge of saucepans have not
been washed well
Reposition saucepans
Spray arms are partially blocked
7. Dishes only
partially washed
The dishes have not been
loaded properly
The end of the drain pipe is
immersed in water
An incorrect amount of detergent
has been measured out, or the
detergent is old and hard
The cap of the salt container is
not closed properly
The wash programme is not
thorough enough
8. Detergent not
dispensed or
partially
dispensed
9. Presence of
white spots on
dishes
10. Noise during
wash
11. The dishes
are not
completely dry
Choose a more vigorous programme
Tighten it properly
Cutlery, dishes, pans, etc., stop
the detergent dispenser from
opening
Position dishes so as not to obstruct
the dispenser
Mains water is too hard
Check salt and rinse aid level and
regulate. Should the fault persist,
contact the Technical Assistance
Centre
The dishes knock against one
another
Re-check loading of dishes in the
basket
The revolving arms knock
against the dishes
Re-check loading of dishes in the
basket
Inadequate air flow
Leave the dishwasher door ajar at
the end of the wash program to
allow the dishes to dry naturally
Rinse aid missing
Fill the rinse aid dispenser
33
Remove spray arms by unscrewing
ring nuts clockwise and wash under
running water
Do not place the dishes too close
together
The end of the drain pipe must not
come into contact with the outflow
water
Increase the measure according to
how dirty the dishes are, or change
detergent
N.B.: Should any of the above situations result in a bad wash performance or insufficient
rinsing, remove dirt deposits from the dishes by hand since the final drying cycle hardens
the dirt, making it difficult to remove with a subsequent wash.
If the malfunction continues, contact the Technical Assistance Centre, quoting the model of
the dishwasher. This is found on the plate on the upper section of the inside of the
dishwasher door, or on the warranty. This information will make it possible to take quicker,
more effective action.
Assistance and Warranty
The product is guaranteed under the law, and under the terms and conditions
stated on the warranty certificate included with the product. The certificate
should be stored and shown to an authorized Technical Assistance Centre in
case of need, together with the proof of purchase. You can also check the
warranty conditions on our website.
For assistance, please fill in the online form or contact us at the number
indicated on the support page of our website.
The manufacturer declines all responsibility for any printing errors in this booklet.
Moreover, the manufacturer reserves the right to make any changes deemed useful to its
products without changing their essential characteristics.
34
l WEEE
This appliance is marked a
cording to the European directive
2012/19/EUon Waste Electrical
and
Electronic
Equipment
(WEEE).
WEEE contains both polluting substances
(which can cause negative consequences
for the environment) and basic components
(which can be re-used).
It is important to have WEEE subjected to
specific treatments, in order to remove
and dispose properly all pollutants,
and recover and recycle all materials.
should not
household waste;
treated
as
l WEEE should be handed over to the
relevant collection points managed by
the municipality or by registered
companies. In many countries, for large
WEEE, home collection could be
present.
In many countries, when you buy a new
appliance, the old one may be returned to
the retailer who has to collect it free of
charge on a one-to-one basis, as long as
the equipment is of equivalent type and
has the same functions as the supplied
equipment.
Individuals can play an important role in
ensuring that WEEE does not become an
environmental issue; it is
35
be
EN
20. ENVIRONMENTAL CONDITIONS
A. WIRELESS PARAMETERS
Wi-Fi
Specifications (Wi-Fi)
A
B
C
802.11 b/g/n
2,412 GHz. - 2,484 GHz.
802.11b, DSSS 1 Mbps =
+19.5 dBm
802.11b, CCK 11 Mbps =
+18.5 dBm
802.11g, OFDM 54 Mbps =
+18.5 dBm
802.11n, MCS7 =
+14 dBm
802.11b = 1024 bytes,
-80 dBm
D
E
802.11g = 1024 bytes,
-70 dBm
802.11n = 1024 bytes,
-65 dBm
Specifications
(Bluetooth)
NFC
Wi-Fi (One Fi/Smart Fi)
Bluetooth v4.2
ISO/IEC 14443 Type A
and NFC Forum Type 4
802.11 b/g/n
2,412 GHz. - 2,484 GHz.
13,553-13,567 MHz (centre
frequency 13,560 MHz)
2,412 GHz. - 2,484 GHz.
Basic data Rate:
RF Transmit Power (Typ):
+4 dBm
802.11b (11Mbps) +18,5
± 2 dBm
Enhanced data Rate:
RF Transmit Power (Typ):
+2 dBm
802.11g (54Mbps) +16
± 2 dBm
▬
BLE
RF Transmit Power (Typ):
+7.5 dBm
Basic data Rate:
Sensivity @ 0.1% BER: -98
dBm
Enhanced data Rate:
Sensivity @ 0.01% BER: -98
dBm
802.11n HT40 = 1024 bytes,
-65 dBm
BLE
Sensivity @ 0.1% BER: -98
dBm
▬
▬
WIRELESS PARAMETERS:
A Wireless Standard - B Frequency range -
802.11n (HT20, MCS7) +14
± 2 dBm
802.11b (11Mbps)
-93 dBm
802.11g (54Mbps)
-85 dBm
▬
802.11n (HT20, MCS7)
-82 dBm
< 42dBµA/m (at 10 m)
C
Max Transmit Power -
D
▬
Minimum Receiving Sensitivity -
E Magnetic field limit
EN
With this the Candy Hoover Group Srl, declares that this appliance marked with
complies with
the essential requirements of the Directive 2014/53/EU. To receive a copy of the declaration of conformity,
please contact the manufacturer at: www.candy-group.
36
fkhldsk
fkhldsk
fkhldsk
- CDIN L -
19.03 - 41048241 - Canon Italia - Business Services Channel
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising