Candy | GV 149T3W/1-80 | Candy GV 149T3W/1-80 User manual

Candy GV 149T3W/1-80 User manual
EN
Thank-you for choosing a Candy washing
machine. We are confident it will loyally
assist you in safely washing your clothes,
even delicates, day after day.
Environmental conditions
This appliance is marked according to
the European directive 2012/19/EU
on Waste Electrical and Electronic
Equipment (WEEE).
WEEE contains both polluting substances (which
can cause negative consequences for the
environment) and basic components (which can
be re-used). It is important to have WEEE
subjected to specific treatments, in order to
remove and dispose properly all pollutants, and
recover and recycle all materials. Individuals can
play an important role in ensuring that WEEE
does not become an environmental issue; it is
essential to follow some basic rules:
You can register your product at
www.registercandy.com to gain faster
access to supplementary services solely
reserved to our most loyal customers.
Carefully read this manual for correct and
safe appliance use and for helpful tips on
efficient maintenance.
Only use the
after carefully reading
We recommend you
manual on hand and in
any future owners.
washing machine
these instructions.
always keep this
good conditions for
l WEEE should not be treated as household
Please check that the appliance is
delivered with this instruction manual,
warranty certificate, service centre address
and energy efficiency label. Also check that
plugs, curve for drain hose and liquid
detergent or bleach tray (only on some
models) are included. We recommend you
keep all these components.
In many countries, when you buy a new
appliance, the old one may be returned to the
retailer who has to collect it free of charge on a
one-to-one basis, as long as the equipment is of
equivalent type and has the same functions as
the supplied equipment.
Each product is identified by a unique 16character code, also called the “serial
number”, printed on the sticker affixed to
the appliance (porthole area) or in the
document envelope found inside the
product. This code is a sort of specific
product ID card that you will need to
register it and should you need to contact
the Candy Customer Service Centre.
1. GENERAL SAFETY RULES
waste;
l WEEE should be handed over to the relevant
collection points managed by the municipality or
by registered companies. In many countries, for
large WEEE, home collection could be present.
Contents
2. INSTALLATION
3. PRACTICAL TIPS
4. MAINTENANCE AND CLEANING
5. QUICK USER GUIDE
6. CONTROLS AND PROGRAMS
7. CUSTOMER SERVICE CENTRE AND
WARRANTY
2
l This
appliances is intended to
be used in household and
similar applications such as:
- Staff kitchen areas in shops, offices
and other working environments;
- Farm houses;
- By clients in hotels, motels and
other residential type environments;
- Bed and breakfast type environments.
A different use of this appliance
from household environment
or from typical housekeeping
functions, as commercial use by
expert or trained users, is excluded
even in the above applications. If
the appliance is used in a manner
inconsistent with this it may reduce
the life of the appliance and may
void the manufacturer’s warranty.
Any damage to the appliance or
other damage or loss arising
through use that is not consistent
with domestic or household use
(even if located in a domestic or
household environment) shall not
be accepted by the manufacturer to
the fullest extent permitted by law.
l Children
should be supervised
to ensure that they do not play
with the appliance.
l Children
of less than 3 years
should be kept away unless
continuously supervised.
l If
the supply cord is damaged, it
must be replaced by the
manufacturer, its service agent
or similarly qualified persons in
order to avoid a hazard.
l Only
use
the
hose-sets
supplied with the appliance for
the water supply connection
(do not reuse old hose-sets).
l Water
pressure must be between
0,05 MPa and 0,8 MPa.
l Make
sure that a carpet do not
obstruct the base of the machine
and ventilation openings.
appliance can be used by l The OFF condition is reached
by placing the reference mark on
children aged from 8 years and
the programmes control/knob in
above and persons with reduced
the vertical position. Any other
physical, sensory or mental
different position of such control
capabilities or lack of experience
sets the machine in ON condition
and knowledge if they have been
(only for models with programmes
given supervision or instruction
knob).
concerning use of the appliance
l This
3
EN
in a safe way and understand the
hazards involved.
Children shall not play with the
appliance. Cleaning and user
maintenance shall not be made
by children without supervision.
1. GENERAL SAFETY
RULES
l After
installation, the appliance l Do not expose the washing
must be positioned so that the
machine to rain, direct sunlight
plug is accessible.
or other weather elements.
l The
maximum load capacity of l When moving, do not lift the
dry clothes depends on the
washing machine by the knobs
model used (see control panel).
or detergent drawer; during
transport, never rest the
l To consult the product fiche
porthole on the trolley. We
please refer to the manufacturer
recommend two people lift the
website.
washing machine.
Safety instructions
l In
the event of fault and/or
malfunction, turn off the
washing machine, close the
water faucet and do not tamper
with the appliance.
Immediately
contact
the
Customer Service Centre and
only use original spare parts.
Failure to observe these
instruction may jeopardise
appliance safety.
l Before
cleaning or maintaining
the washing machine, unplug
the appliance and turn off the
water faucet.
l Make
sure the electrical system
is grounded. Otherwise, seek
qualified professional assistance.
l Please
do not use converters,
multiple sockets or extension
cords.
WARNING:
water may reach very high
temperatures during the
wash cycle.
Appliance complies with
European Directives:
l 2006/95/EC (LVD);
l 2004/108/EC (EMC);
l 2009/125/EC (ErP);
l 2011/65/EU (RoHS)
l Make
sure there is no water in
the drum before opening the
porthole.
l Do
not pull on the power cord
or appliance to unplug the
machine.
and subsequent amendments.
4
l Cut
the tube straps, being
careful not to damage the tube
and power cord.
EN
2. INSTALLATION
1
A
B
A
B
l Unscrew
the 2 or 4 screws (A)
on the back and remove the 2
or 4 shims (B) as illustrated in
figure 1.
B
B
A
A
l Close
the 2 or 4 holes using
the plugs included in the
instruction envelope.
l If
the washing machine is built-in,
after cutting the hose straps,
unscrew the 3 or 4 screws (A) and
remove the 3 or 4 shims (B).
2
A
1
l In
some models, 1 or more
shims will fall inside the machine:
tilt the washing machine forward
to remove them. Close the holes
using the plugs found in the
envelope.
2
3
B
WARNING:
keep packaging materials
away from children.
C
l Place
the polionda sheet on
the bottom as shown in figure
2 (according to the model,
consider version A, B or C).
3
2
5
1
Hydraulic connections
3
l Connect the water tube to the faucet, only
using the drain tube supplied with the
washing machine (fig. 3).
DO NOT OPEN THE FAUCET.
l Some models may include one or more of
the following features:
4
l HOT&COLD (fig. 4):
water mains connection settings with hot
and cold water for higher energy savings.
Connect the grey tube to the cold water
faucet
and the red one to the hot water
faucet. The machine can be connected to
the cold water faucet only: in this case,
some programs may start a few minutes
later.
1
5
l AQUASTOP (fig. 5):
a device located on the supply tube that
stops water flow if the tube deteriorates;
in this case, a red mark will appear in the
window “A” and the tube must be
replaced. To unscrew the nut, press the
one-way lock device "B".
6
B
A
B
A
l AQUAPROTECT – SUPPLY TUBE WITH
GUARD (fig. 6):
Should water leak from the primary
internal tube "A", the transparent
containment sheath "B" will contain water
to permit the washing cycle to complete.
At the end of the cycle, contact the
Customer Service Centre to replace the
supply tube.
7
Setting
l Near the washing machine to the wall,
min 4 cm
max 100 cm
being careful that the tube is not bent or
crushed, and place the drain tube in the
tub or, preferably, connect it to a wall
drain at least 50 cm high with diameter
greater than the washing machine tube
(fig. 7).
6
+2,6 mt
max
min 50 cm
max 85 cm
l Level the appliance using the feet as
EN
8
illustrated in figure 8:
a. turn the nut clockwise to release the
screw;
b. rotate the foot to raise or lower it until it
adheres to the floor;
c. lock the foot, screwing in the nut, until it
adheres to the bottom of the washing
machine.
l Plug in the appliance.
A
B
WARNING:
contact the Customer Service Centre
should
the
power
cord
need
replacement.
C
Detergent drawer
9
1
The detergent draw is split into 3
compartments as illustrated in figure 9:
l compartment "1": for prewash detergent;
l compartment “ ”: for special additives,
softeners, starch fragrances, etc.;
2
WARNING:
only use liquid products; the washing
machine is set to automatically dose
additives at each cycle during the last
rinse.
10
l compartment "2": for washing detergent.
A liquid detergent cup is also included in
some models (fig. 10). To use it, place it in
compartment "2". This way, liquid
detergent will only enter the drum at the
right time. The cup can also be used for
bleach when the “Rinse” program is
selected.
11
WARNING:
some detergents are hard to remove.
In this case we recommend using the
specific container to be placed in the
drum (example in figure 11).
7
Is a hot wash required?
3. PRACTICAL TIPS
l Pretreat stains with stain remover or soak
Load tips
dried in stains in water before washing to
reduce the necessity of a hot wash
programme.
Save up to 50% energy by using a 60°C
wash programme.
WARNING: when sorting laundry, make
sure:
Following is a quick guide with tips and
recommendations on detergent use at the
various temperatures. In any case, always
read the instructions on the detergent for
correct use and doses.
- have eliminated metallic objects such as
barrettes, pins, coins, from laundry;
- to have buttoned pillow cases, closed
zips, tied loose belts and long robe
ribbons;
- to have removed rollers from curtains;
- to have carefully read clothing washing
labels;
- to have removed any persistent stains
using specific detergents.
When washing heavily soiled whites,
we
recommend
using
cotton
programs of 60°C or above and a
normal washing powder (heavy duty)
that contains bleaching agents that at
medium/high
temperatures
provide
excellent results.
l When washing rugs, bedcovers or other
heavy clothing, we recommend you avoid
centrifuging.
l To wash wool, make sure the item can be
machine washed and marked by the
“Pure virgin wool” symbol with the “Does
not mat” or “Machine washable” label.
For washes between 40°C and 60°C
the type of detergent used needs to be
appropriate for the type of fabric and
level of soiling.
Normal powders are suitable for “white”
or colour fast fabrics with high soiling,
while liquid detergents or “colour
protecting” powders are suitable for
coloured fabrics with light levels of
soiling.
Helpful suggestions for the user
A guide environmentally friendly and
economic use of your appliance.
Maximise The Load Size
l Achieve the best use of energy, water,
detergent and time by using the
recommended maximum load size.
Save up to 50% energy by washing a full
load instead of 2 half loads.
For washing at temperatures below
40°C we recommend the use of liquid
detergents or detergents specifically
labeled as suitable for low temperature
washing.
Do you need to pre-wash?
l For heavily soiled laundry only!
SAVE detergent, time, water and
between 5 to 15% energy consumption
by NOT selecting Prewash for slight to
normally soiled laundry.
For washing wool or silk, only use
detergents specifically formulated for
these fabrics.
8
EN
4. MAINTENANCE AND
CLEANING
To clean the washing machine exterior, use
a damp cloth, avoiding abrasives, alcohol
and/or solvents. The washing machine does
not require any special care for ordinary
cleaning: clean drawer compartments and
the filter; some tips on how to move the
machine or on long periods of disuse are
provided below.
Drawer cleaning
S u g g e s tio n s fo r m o v e s o r
prolonged disuse
l We recommend you clean the drawer to
avoid accumulating
additive residue.
detergent
and
l Should the washing machine be stored in
an unheated room for a long period of
time, drain all water from tubes.
l To do this, extract the drawer using slight
force, clean it with running water and
reinsert it in its housing.
l Unplug the washing machine.
l Detach the tube from the strap and lower
it, fully draining water into a bowl.
Filter cleaning
l Secure the drain tube with the strap when
finished.
l The washing machine comes with a
special filter able to trap large residue,
such as buttons or coins, which could
clog the drain.
l Only available on certain models: pull out
the corrugated hose, remove the stopper
and drain the water into a container.
l Before
unscrewing the filter, we
recommend you place an absorbent cloth
under it to keep the floor dry.
l Turn the filter counter-clockwise to the
limit stop in the vertical position.
l Remove and clean the filter; when
finished, replace it turning it clockwise.
l Repeat the previous steps in reverse
order to reassemble all parts.
9
5. QUICK USER GUIDE
This washing machine automatically adapts
the level of the water to the type and
quantity of washing. This system gives a
decrease in energy consumption and a
sensible reduction in washing times.
6. CONTROLS AND
PROGRAMS
A
Program selection
l Turn on the washing machine and select
the required program.
L
l Adjust
the washing temperature if
necessary and press the required "option"
buttons.
M
l Press the START/PAUSE button to start
washing.
Should power go out when the washing
machine is running, a special memory
saves the settings and, when power
returns, the machine resumes the cycle
from where it left off.
l The message "end" will appear on the
display or the corresponding led will turn
on at the end of the program.
Wait until the porthole locked light
turns off: about 2 minutes after the
program ends.
B
C
D
E
F
G
H
I
A Programme selector with OFF
position
B START/PAUSE button
C SPIN SELECTION button
D TEMPERATURE SELECTION
button
E DELAY START button
l Turn off the washing machine.
F STAIN LEVEL button
For any type of wash, see the program
table and follow the operating sequence
as indicated.
G EXTRA RINSE button
Technical data
I
H OPTIONS button
EASY IRON button
L Digital display
Water pressure:
min 0,05 Mpa
max 0,8 Mpa
M DOOR LOCKED indicator light
Spin r.p.m.:
See rating plate.
Power input / Power current fuse amp /
Supply voltage:
See rating plate.
10
START/PAUSE button
Opening the door
Close the door BEFORE selecting the
button START/PAUSE.
A special safety device prevents the
door from being opened immediately
after the end of the cycle.
Wait for 2 minutes after the wash
cycle has finished and the "Door
Security" light has gone out before
opening the door.
l Press to start the selected cycle.
When the START/PAUSE button has
been pressed, the appliance can take
few seconds before it starts working.
PROGRAMME selector with OFF
position
ADD OR REMOVE ITEMS AFTER THE
PROGRAMMES HAS STARTED (PAUSE)
l Press and hold the START/PAUSE
button for about 2 seconds (some
indicator light and the time remaining
indicator will flash, showing that the
machine has been paused).
When the programme selector is turned
the display lights up to show the settings
for the programme selected.
For energy saving, at the end of the
cycle or with an inactivity period, the
display level contrast will decrease.
l Wait 2 minutes until the safety device
unlocks the door.
N.B.: To switch the machine off, turn the
programme selector to the OFF
position.
l After you have added or removed items,
close the door and press the
START/PAUSE button (the programme
will start from where it left off).
l Press the START/PAUSE button to start
the selected cycle.
CANCELLING THE PROGRAMME
l Once a programme is selected the
programme selector remains stationary on
the selected programme till cycle ends.
l To cancel the programme, set the
selector to the OFF position.
l Switch off the washing machine by
l Select a different programme.
turning the selector to OFF.
11
EN
The programme selector must be
returned to the OFF position at the end
of each cycle or when starting a
subsequent wash cycle prior to the next
programme being selected and started.
WARNING:
Don’t touch the display while inserting
the plug because the machines
calibrates the systems during the first
seconds: touching the display, the
machine couldn’t work property. In
this case, remove the plug and repeat
the operation.
l Re-set the programme selector to the
OFF position.
l It is not possible to raise the temperature
over the maximum allowed for every
programme, in order to save the fabrics.
The option buttons should be selected
before pressing the START/PAUSE
button.
If an option is selected that is
not compatible with the selected
programme then the option indicator
first flashes and then goes off.
DELAY START button
l This button allows you to pre-programme
the wash cycle to delay the start of the
cycle for up to 24 hours.
l To delay the start use the following
procedure:
SPIN SELECTION button
- Set the required programme.
l By pressing this button, it is possible to
reduce the maximum speed, and if you
wish, the spin cycle can be cancelled.
l To reactivate the spin cycle press the button
until you reach the spin speed you would
like to set.
To prevent damage to the fabrics, it is
not possible to increase the speed
over that which is automatically
suitable during the selection of the
program.
- Press the button once to activate it (h00
appears on the display) and then press
it again to set a 1 hour delay (h01
appears on the display). The pre-set
delay increases by 1 hour each time the
button is pressed, until h24 appears on
the display, at which point pressing the
button again will reset the delay start to
zero.
- Confirm by pressing the START/PAUSE
button (the light on the display starts to
flash). The countdown will begin and
when it has finished the programme will
start automatically.
l It is possible to modify the spin speed
without pausing the machine.
l It is possible to cancel the delay start by
The machine is fitted with a special
electronic device, which prevents the
spin cycle should the load be
unbalanced.
This reduces the noise and vibration in
the machine and so prolongs the life of
your machine.
If there is any break in the power supply
while the machine is operating, a special
memory stores the selected programme
and, when the power is restored, it
continues where it left OFF
TEMPERATURE SELECTION button
l By selecting this button there is a choice
turning the programme selector to OFF.
STAIN LEVEL button
l This button allows you to change the
temperature of the wash cycles.
12
of 3 levels of wash intensity, depending
on how much the fabrics are soiled (can
be used only on some programmes as
shown in the table of programmes).
- HYGIENE
l With this option it is possible to hygienize
the clothes, the washing programme
reach a temperature of 60°C.
the indicator light will automatically show
the stain level set for that programme.
l Selecting a different stain level the
- NIGHT CYCLE
l This option reduces the intermediate spin
speed to 400 rpm, where applicable,
increase the water level during rinsing and
keep the laundry immersed in water after the
final rinse, in order to spread the fibre
sevenly.
relevant indicator will light up.
EXTRA RINSE button
l This button allows you to add rinses at
the end of the washing cycle. The
maximum number of extra rinses is
related to the programme selected.
l During the phase in which the water is
held in the tub, the relevant indicator light
blink to show that the machine is at a
standstill.
l This function has been studied for the
people with delicate and sensitive skin,
for which also a least residue of detergent
can cause irritations or allergies.
l Deselect the option to end the cycle with a
l It advises to also use this function for the
l Thanks to electronic control, the water
spin dry (which may be reduced or cancelled
using the appropriate button) and emptying
phase.
children items and in case of washings of
very dirty items, for which it is due to use
a lot of detergent, or in the washing of
toweling items whose fibres mostly have
the tendency to hold the detergent.
in the intermediate phases is emptied
silently, making this option very useful for
washing at night.
EASY IRON button
OPTIONS button
This function allows you to minimizes
creases as much as possible, eliminating
the intermediate spins or reducing the
intensity of the last one.
You can choose between three different
options:
- PREWASHING
l This option allows you to make a prewash
and it is particularly useful for heavily
soiled loads (can be used only on some
programmes as shown in the table of
programmes).
l We recommend you use only 20% of the
recommended quantities shown on the
detergent pack.
13
EN
l Once the programme has been selected
Digital Display
The display’s indicator system allows you to
be constantly informed about the status of
the machine.
2
3
4
5
6
7
the wash cycle has finished and the
DOOR LOCKED light has gone out before
opening the door. At the end of the cycle
turn the programme selector to OFF.
2) SPIN SPEED
2
This show the spin speed of the selected
programme that can be changed or omitted
by the relevant button.
1
8
9 10
3) WASH TEMPERATURE
1) DOOR LOCKED INDICATOR LIGHT
3
1
l The indicator light is illuminated when the
This show the washing temperature of the
selected programme that can be changed
(where allowed) by the relevant button.
door is fully closed.
4) CYCLE DURATION
Close the door BEFORE selecting the
START/PAUSE button.
4
l When START/PAUSE
is pressed on
the machine with the door closed, the
indicator will flash momentarily and then
illuminate.
If the door is not properly closed,
the light will continue to flash for
about 7 seconds, after which the
start command will be automatically
delete. In this case, close the door
in the proper way and press the
START/PAUSE button.
l When a programme is selected the
display automatically shows the cycle
duration, which can vary, depending on
the options selected.
l Once the programme has started you will
be kept informed constantly of the time
remaining to the end of the wash.
l The appliance calculates the time to the
l A special safety device prevents the door
from being opened immediately after the
end of the cycle. Wait for 2 minutes after
14
end of the selected programme based
upon a standard loading, during the cycle,
the appliance corrects the time to that
applicable to the size and composition of
the load.
5) STAIN LEVEL
{
EN
5
9) DELAY START
9
l Once the programme has been selected,
This flashes when delay start has been set.
the indicator light will automatically show
the stain level set for that programme.
10) Kg Check (function active only on
Cotton and Synthetics programmes)
l Selecting a different stain level the
relevant indicator will light up.
6) EXTRA RINSES
10
l During the first minutes of the cycle, the
{
"Kg Check" indicator remain on while the
intelligent sensor will weigh the laundry
and adjust the cycle time, water and
electricity consumption accordingly.
6
The indicator lights show the extra rinses
selected by the relevant button.
l Through every wash phase "Kg Check"
7) OPTIONS
}
allows to monitor information on the wash
load in the drum and in the first minutes
of the wash it:
7
- adjusts the amount of water required;
The indicator lights show the option that
can be selected by the relevant button
(PREWASH, HYGIENE and NIGHT CYCLE).
- determines the length of the wash cycle;
8) WI-FI (some models only)
- controls rinsing according to the type of
fabric selected to be washed it;
- adjusts the rhythm of drum rotation for
the type of fabric being washed;
8
l In the models with the Wi-Fi option, the
- recognizes the presence of lather,
increasing, if necessary, the amount of
water during rinsing;
icon indicates that the Wi-Fi system is
working.
l For all other information in the Wi-Fi
system, there is a specific manual inside
the machine.
- adjusts the spin speed according to the
load, thus avoiding any imbalance.
15
Table of programmes
2
TEMP.°C
kg *
(MAX.)
PROGRAM
Recommended
Max.
Rapid 14 Min
1,5
1,5
1,5
1,5
30°
30°
Rapid 30 Min
2,5
2,5
2,5
2,5
30°
30°
Rapid 44 Min
3,5
3,5
3,5
3,5
30°
40°
1
DETERGENT
2
1
Whites
1)
8
9
10
11
60°
90°
( )
Mixed
1)
4
4,5
5
5,5
40°
60°
( )
Baby
1)
5,5
6
6,5
7
60°
60°
Mix & Wash
8
9
10
11
40°
40°
Rinse
-
-
-
-
-
-
Drain + Spin
-
-
-
-
-
-
Silk
2
2
2
2
30°
30°
Hand
2
2
2
2
30°
30°
Wool
2
2
2
2
40°
40°
Delicates
2,5
2,5
2,5
2,5
40°
40°
EcoMix 20°
8
9
10
11
20°
20°
8
9
10
11
40°
60°
**
1)
16
( )
( )
(Only for models with liquid
detergent compartment)
When only a limited number of
articles have stains which require
treatment with liquid bleaching
agents, preliminary removal of
stain can be carried out in the
washing machine.
Pour the bleach into the liquid
bleach container, inserted into the
compartment marked "2" in the
detergent drawer, and set the
special programme RINSE.
When this phase has terminated,
turn the programme selector on
the OFF position, add the rest of
the fabrics and proceed with a
normal wash on the most suitable
programme.
Please read these notes:
* Maximum load capacity of dry clothes,
according to the model used (see control
panel).
** STANDARD COTTON PROGRAMMES
ACCORDING TO (EU) No 1015/2010 and
No 1061/2010.
COTTON PROGRAMME
TEMPERATURE OF 60°C.
WITH
A
COTTON PROGRAMME
TEMPERATURE OF 40°C.
WITH
A
Only with PREWASH option
selected
(programmes
with
PREWASH option available).
These programmes are suitable to
clean normally soiled cotton laundry and
they are the most efficient programmes
in terms of combined energy and water
consumptions for washing cotton
laundry.
These
programmes
have
been
developed to be compliant with the
temperature on the wash label on the
garments and the actual water
temperature may slightly differ from the
declared temperature of the cycle.
1)
The spin speed may also be reduced, to
match any guidelines suggested on the
fabric label, or for very delicate fabrics
cancel the spin completely this option is
available with a spin speed button. This
function can be activated with the button
SPIN SELECTION.
If the label does not indicate specific
information, it is possible to use the
maximum spin expected in the program.
17
For the programmes shown you
can adjust the duration and
intensity of the wash using the
STAIN LEVEL button.
EN
An over dosing of detergent can cause
excessive foaming.
If the appliance detects the presence of
excessive foam, it may exclude the spinning
phase or extend the duration of the program
and increase water consumption.
Programmes selection
To clean different types of fabrics and
various levels of dirt, the washing machine
has specific programs to meet every need
of washing (see table of programmes).
Rapid 14 Min / 30 Min / 44 Min
A complete washing cycle (wash, rinse and
spin). This programme is particularly suited
to slightly dirty cottons and mixed fabrics.
With this programme it is recommended to
use only 20% of the detergent normally
used to avoid waste.
Whites
Made to have a perfect washing. The final
spin at maximum speed gives more efficient
removal.
Mixed
The washing and rinsing are optimized in the
rhythms of rotation of the drum and to the
water levels. The gentle spin, ensures a
reduced formation of creases in the fabric.
Baby
This program allows you to wash all baby
clothes getting a perfect clean and
sanitizing effect, setting the temperature at
60°C minimum.
To optimize the result of the sanitizing effect
we recommend the use of powder detergent.
Drain + Spin
The program completes the drain and a
maximum spin. It is possible to delete or
reduce the spin with the SPIN SELECTION
button.
Silk
Dedicated program for silk fabrics that can be
wash with a washing machine washable. The
rotations of the drum are delicate, the
temperature does not exceed 30°C and the
program ends with a gentle spin.
Hand
Program for hand wash only clothes, the
program ends with 3 rinses and a slow spin.
Wool
This program performs a wash cycle
dedicated to the wool fabrics that can be
washed in a washing machine, or the
articles to be washed by hand.
Delicates
This program alternates among moments of
work during breaks and is particularly suitable
for washing delicate fabrics . The wash cycle
and rinses are carried out with a high level of
water to ensure the best performance.
Mix & Wash
The program allow you to mix different fabrics
(ex: cotton + synthetic, etc. ..) and wash them
with low energy consumption, because the
temperature in the wash step does not
exceed 40°C.
EcoMix 20°
This innovative programme, allows you to wash
different fabrics and colours together, such as
cottons, synthetics and mixed fabrics at only
20°C and provides an excellent cleaning
performance. Consumption on this program is
about 40% of a conventional 40°C. cottons
wash.
Rinse
This program performs 3 rinses with an
intermediate spin (which can be reduced or
excluded by using the appropriate button). It is
used for rinsing any type of fabric, for example
after a wash carried out by hand.
This program is suitable to clean normally soiled
cotton laundry and it is the most efficient program
in terms of combined energy and water
consumptions for washing cotton laundry.
18
If you believe the washing machine is not working correctly, consult the quick guide
provided below with some practical tips on how to fix the most common problems.
Problem
Possible causes and practical solutions
The washing machine
does not work/start
Make sure it is correctly plugged in.
Make sure power is on.
Check whether the required program was correctly selected and to
have correctly started the machine.
Make sure the fuse has not blown and that the wall socket is working,
testing it with another appliance such as a lamp.
The porthole may not be correctly closed: open and close it again.
The washing machine
does not fill with
water
The washing machine
does not drain water
Make sure the water faucet is open.
Water leaked on the
floor near the washing
machine
The washing machine
does not centrifuge
Strong vibrations are
heard during centrifuge
If a specific ERROR
appears of blinks
Make sure the timer is correct set.
Make sure the filter is not clogged.
Make sure the drain hose is not bent.
Make sure there are no foreign objects in the filter.
This may be due to a leak in the gasket between the faucet and supply
tube; in this case, replace it and tighten the tube and faucet.
This could be due to the fact that water has not been completely
drained: wait a few minutes.
Some models include a "no centrifuge" function: make sure it is not on.
An excessive amount of detergent could prevent centrifuge: reduce the
amount at the next wash.
The washing machine may not be fully levelled: if necessary, adjust
the feet as indicated in the specific section.
Make sure transport brackets were removed.
Make sure the load is evenly distributed.
If error no. 0, 1, 5, 7 or 8 appears or blinks, contact the Customer
Service Centre directly.
If error no. 2 appears or blinks, the machine does not load water.
Make sure the water faucet is open.
If error no. 3 appears or blinks, the machine does not correctly drain.
Make sure the drain is free and that the drain hose is not bent.
If error no. 4 appears or blinks, the machine is too full. Close the
water faucet and contact the Customer Service Centre.
If error no. 9 appears or blinks, turn off the washing machine, wait 10
– 15 seconds and restart the program.
19
EN
7. CUSTOMER SERVICE CENTRE AND WARRANTY
The use of ecological detergents without
phosphates may cause the following effects:
Warranty
The product is guaranteed under the
terms and conditions stated on the
certificate included with the product. The
warranty certificate must be duly filled in
and stored, so as to be shown to the
Authorised Candy Service Centre in
case of need.
- cloudier rinse drain water: This effect is
tied to the suspended zeolites which do
not have negative effects on rinse
efficiency.
- white powder (zeolites) on laundry at
the end of the wash: this is normal, the
powder is not absorbed by fabric and
does not change its colour.
Register your product!
Don’t waste time. Register your washing
machine at once, and discover the
benefits to which you are entitled.
Discover how at www.registercandy.com
or by calling the number stated on the
related material.
- foam in the water at last rinse: this
does not necessary indicate poor rinsing.
- abundant foam: This is often due to the
anionic surfactants found in the
detergents which are hard to eliminate
from laundry.
In this case, do not re-rinse to eliminate
these effects: it will not help at all.
The manufacturer declines all
responsibility for any printing errors in
the booklet included with this product.
Moreover, it also reserves the right to
make any changes deemed useful to its
products without changing their essential
characteristics.
If the problem persists or if you suspect a
malfunction, immediately contact the
Candy Customer Service Centre.
You can also register for the Candy
service plan to receive free home service
after the warranty expires.
Attention: the call is not toll-free. The cost
will be communicated in a voice message
by your telephone operator's customer
service.
Candy recommends you always use
original spare parts available at our
Customer Service Centre.
20
fkhldsk
fkhldsk
fkhldsk
- GVT/GSF (8÷11) -
15.05 - 43010856 - Canon Italia - Business Services Channel - Printed in Italy
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising