Candy | EVOT 10061D3N-UK | Candy EVOT 10061D3N-UK User manual

Candy EVOT 10061D3N-UK User manual
WASHING MACHINE EVOT 10061D3-UK
H
B2
A
B1
V
G
C2
A
C1
p
PROGRAMME/TEMPERATURE SELECTOR
Use this control to select the desired wash programme. Turn the selector (it
can be turned in both directions) so that the programme is opposite the
reference indicator (p). The temperature selected will depend on the
programme. (See the Programme Table).
B1
SPIN SPEED SELECTOR
B2
DELAYED START KEY
C1 COLD WASH
C2 AQUAPLUS (SENSITIVE KEY)
G
DOOR LOCK LAMP
H
START/PAUSE KEY
p
CONTROL POSITION INDICATOR
V
PROGRAMME PHASES LAMPS
This washing machine has a device that ensures that the drum is right-side-up and ready for loading/
unloading clothes when the selected programme is completed.
Programme table mod EVOT 10061D3-UK
max.
temp.
setting
ºC
spin
speed
rpm/min
max.
load
Kg.
Fast coloureds with prewash
90º
1000
6
* Fast coloureds
60º
1000
* Fast coloureds
40º
Delicate coloureds
I
II
x
x
x
x
x
6
x
x
x
x
1000
6
x
x
x
x
30º
1000
6
x
x
x
x
Fast coloureds
50º
display
2
x
x
x
x
Delicate coloureds
40º
display
2
x
x
x
x
Delicate coloureds
30º
display
2
x
x
x
x
Woollens
30º
display
1
x
x
x
Hand wash
30º
display
2
x
x
x
programme
COTTONS
MIXED
SYNTHETICS
DELICATES
SPECIAL
washing powder option keys
load
C
programme for
Gentle rinse
display
Gentle spin
1000
x
x
Empty
EcoMix 20ºC
20º
display
6
x
x
x
Rapid 44
40º
display
3
x
x
x
Rapid 30
30º
display
2
x
x
x
x
* Cotton wash programme requirements according to (EU) 1015/2010 e nº 1061/2010 regulations
60° Cotton wash programme
40° Cotton wash programme
These wash programmes are recommended for soiled cotton fabrics and are the most effective in terms of
both energy efficiency and water consumption.
These programmes have been designed to comply with the recommended wash temperatures specified on
the labelling: the specified temperature may differ slightly from that indicated on the wash cycle.
Technical data mod.
EVOT 10061D3-UK
Mains
voltage
220-230V.
50Hz.
Mains fuse
Amp. rating
Water
pressure
Max.
Power input
10 A.
0,05-0,8 Mpa
1500
programme phases
wash
rinse
spin-drain
IMPORTANT:
- Do not use liquid detergent for programs with a prewash cycle and/or timed start.
PREPARING THE WASH CYCLE
1.- Once the washing is loaded, ensure that the drum doors are properly closed..
2.- Add detergent and additives, not exceeding the maximum level indicator.
x
detergent for pre-wash I
x
detergent for wash programme II
x
fabric conditioner
SELECTING THE DESIRED PROGRAMMES AND OPTIONS
3.- Turn the programme selector (A) to the desired programme.
4.- Press the key or keys for any options desired (C1, C2,).
.- It is advisable to select the required options before pressing the Programme Start key (H).
.- Remember that if the programme has already passed the stage at which an option is activated, that
option will not be implemented.
C1 cold wash key
By pressing this button it is possible to transform every programme into a cold washing one, without
modify other characteristics (water level, times, rythmes, etc..).
Curtains, small carpets, man made delicate fabrics, non coulor fast garments can be safely washed
thanks to this new device.
C2 aquaplus (sensitive key)
Thanks to the new SENSOR ACTIVA SYSTEM, by pressing the key it is possible to run a special
washing cycle applicable to all programs and types of fabric, caring for their fibres and the delicate
skin of the users who use them.
Taking on much more water, together with the new combined action of drum rotation cycles and taking
on and discharging water allow you to obtain perfectly clean, rinsed clothes. More water is used in the
wash to dissolve the detergent completely, ensuring an effective washing action. The water in the
rinses has also been increased to eliminate all trace of detergent in the fibres.
This function has been specifically studied for people with delicate, sensitive skin, who can suffer
irritation or allergy from the slightest detergent residue.
It is also advisable to use this function for children's clothes and delicate fabrics in general, especially
for washing bathrobes, whose fibres tend to retain detergent.
This option is not available for the wool program.
B1 spin selector key
You can use this key to select final spin speed, but only within the range of speeds of the programme
selected. These speeds are displayed via the corresponding lamp. Press the button and keep pressed
until the three speed indicator lights go out ( ).
You can select the desired speed at any time during the programme.
(H). The washing machine
5.- Once you have selected the desired options, press the START key
will start up and one of the time remaining lamps /programme phase (V) will come on. This lamp
indicates approximately how much time is left before the wash programme is completed or the
programme phase: it will change as the programme progresses. To cancel an option after setting, just
press the option key again (the indicator lamp will go out).
B2 delayed start key
The washing machine can be set to start the programme selected 3, 6, or 9 hours after setting. To do
this, proceed as follows:
- Select the desired programme via the programme selector A.
- Press the delayed start key until the desired delay indicator lamp lights up.
(H).
- Press the start/pause key
- The washing machine will start up after the time selected.
If you prefer to cancel the programmed start-up time, press the (B2) key again until all the delay lights
have switched off.
Time remaining to end of cycle or programme phase display (V).
Models with this feature display the APPROXIMATE time remaining to the end of the programme in
minutes, or the current wash phase of the programme set. The programme times may vary depending
on the temperature selected, ambient temperature, mains water pressure, the quantity and type of
washing.
.
“Door lock” lamp (G)
The door lamp flashes when a wash programme starts, and then burns steadily. From that moment on
the door is locked (DOOR LOCK).
The DOOR LOCK lamp remains on during the whole wash cycle, thus preventing the door from
opening.
At the end of the wash cycle, the safety devices are deactivated, the light goes out and the door can
then be opened.
Cancel-change programs
Once you have started a program, and wish to change or cancel it, you should proceed in the following
manner,
- Put the program selector in the OFF position. At that instant, you have cancelled the program
and can if you wish to do so, select a new one.
- Select the new program.
(H) key until one of the programme phase lights turns on.
- Press the
The washing machine will perform the new selected program.
Programme Pause
To pause the wash programme so that more washing can be added, proceed as follows:
- Press the (H) key until the lights on the option keys and the programme phase light have turned on.
- When the Door Lock lamp goes out (after approx. 2 minutes), open the door and put the additional
washing into the drum.
- Close the drum door and the lid properly.
(H), the time remaining lamp will light up and the machine will continue with
- Press the start key
the programme.
At the end of the programme, all the programme phase lights will be lit up, and safety door light will
shut off.
For your own safety, set the programme selector to OFF before opening the
washing-machine lid and the drum doors to remove the washing.
28.09.15 / H - 43011353 EN
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising