Candy | GO W485D-UK | Candy GO W485D-UK User manual

Candy GO W485D-UK User manual
EN
User instructions
GO W 485 D
EN
OUR COMPLIMENTS
With the purchase of this Candy household appliance, you
have shown that you will not accept compromises: you want
only the best.
Candy is happy to present their new washing machine, the
result of years of research and market experience through
direct contact with Consumers. You have chosen the quality,
durability and high performance that this washing machine
offers.
Candy is also able to offer a vast range of other household
appliances: washing machines, dishwashers, washer-dryers,
cookers, microwave ovens. Traditional ovens and hobs,
refrigerators and freezers.
Ask your local retailer for the complete catalogue of Candy
products.
Please read this booklet carefully as it provides important
guide lines for safe installation, use and maintenance and
some useful advise for best results when using your washing
machine.
Keep this booklet in a safe place for further consultation.
When contacting Candy
or a Customer Services Centre always refer to the Model,
No., and G number (if applicable of the appliance see
panel).
2
EN
CHAPTER
INDEX
Introduction
General points on delivery
1
Guarantee
2
Safety Measures
3
Technical Data
4
Setting up and Installation
5
Control Description
6
Table of Programmes
7
Selection
8
Detergent drawer
9
The Product
10
Washing
11
Drying cycle
12
Automatic washing/Drying cycle
13
Cleaning and routine maintenance
14
Faults Search
15
3
EN
CHAPTER 1
GENERAL POINTS ON DELIVERY
On delivery, check that the following are included with the
machine:
A) INSTRUCTION MANUAL
B) CUSTOMER SERVICE ADDRESSES
C) GUARANTEE CERTIFICATES
D) CAPS
E) BEND FOR OUTLET TUBE
KEEP THEM IN A SAFE PLACE
A
Check that the machine has not incurred damage during
transport. If this is the case, contact your nearest Candy
Centre.
B
C
EN
CHAPTER 2
D
GUARANTEE
The appliance is supplied with a guarantee certificate
which allows free use of the Technical Assistance Service.
4
E
EN
CHAPTER 3
SAFETY MEASURES
IMPORTANT:
FOR ALL CLEANING AND MAINTENANCE WORK
● Remove the plug
● Turn off the water inlet tap.
● All Candy appliances are earthed. Ensure that the main
electricity circuit is earthed. Contact a qualified electrician
if this is not the case.
Appliance complies with European Directives
73/23/EEC and 89/336/EEC, replaced by 2006/95/EC and
2004/108/EC, and subsequent amendments.
● Do not touch the appliance with wet or damp hands or
feet.
● Do not use the appliance when bare-footed.
● Extreme care should be taken if extension leads are used
in bathrooms or shower rooms. Avoid this where possible.
WARNING:
DURING THE WASHING CYCLE, THE WATER CAN
REACH A TEMPERATURE OF 90°C.
● Before opening the washing machine door, ensure that
there is no water in the drum.
5
EN
● Do not use adaptors or multiple plugs.
● This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not
play with the appliance.
● Do not pull the mains lead or the appliance itself to
remove the plug from the socket.
● Do not leave the appliance exposed to atmospheric
agents (rain, sun etc.)
● In the case of removal, never lift the appliance by the
knobs or detersive drawer.
● During transportation
do not lean the door against the trolley.
Important!
When the appliance location is on carpet floors, attention
must be paid so as to ensure that there is no obstruction to
the bottom vents.
● Lift the appliance in pairs as illustrated in the diagram.
● In the case of failure
and/or incorrect operation, turn the washing machine off,
close the water inlet tap and do not tamper with the
appliance. Contact a Candy Technical Assistance Centre for
any repairs and ask for original Candy spare parts.
Avoidance of these norms may compromise the safety of the
appliance.
● Should the supply cord (mains cable) be demaged, this is
to be replaced by a specific cable available from the after
sales service centre.
6
EN
CHAPTER 4
85
cm
60 cm
54 cm
TECHNICAL DATA
MAXIMUM WASH
LOAD DRY
kg
Washing
Drying
8
5
NORMAL WATER LEVEL
l
6÷15
POWER INPUT
W
2150
ENERGY CONSUMPTION
(PROG. 90°C)
kWh
1,8
POWER CURRENT FUSE
AMP
A
13
SPIN
r.p.m.
SEE RATING PLATE
WATER PRESSURE
MPa
min. 0,05
max. 0,8
SUPPLY VOLTAGE
V
220 - 240
7
EN
CHAPTER 5
SETTING UP INSTALLATION
Move the machine near its permanent position without the
packaging base.
Carefully cut the securing strap that holds the main cord and
the drain hose.
Remove the 3 fixing screws marked (A) and remove the 3
spacers marked (B)
Remove the screw (C).
A spacer will fall inside the machine.
By tilting the machine, remove the above mentioned spacer.
Cover the 4 holes using the caps provided in the instruction
booklet pack.
WARNING:
DO NOT LEAVE THE PACKAGING IN THE REACH OF
CHILDREN AS IT IS A POTENTIAL SOURCE OF DANGER.
8
EN
Fix the sheet of corrugated material on the bottom as shown
in picture.
Connect the fill hose
to the tap.
The appliance must be connected to the water mains using
new hose-sets. The old hose-sets should not be reused.
IMPORTANT:
DO NOT TURN THE TAP ON AT THIS TIME.
Position the washing machine next to the wall. Hook the
outlet tube to the edge of the bath tub, paying attention
that there are no bends or contractions along the tube.
It is better to connect the discharge hose to a fixed outlet of
a diameter greater than that of the outlet tube and at a
height of min. 50 cm. If is necessary to use the plastic sleeve
supplied.
The appliance must not be installed behind a lockable door,
a sliding door or a door with a hinge on the opposite side to
that of the washer dryer.
max 100 cm
min 4 cm
+2,6 mt max
min 50 cm
max 85 cm
9
EN
Use the 4 feet to level the machine with the floor:
a) Turn the nut clockwise to release the screw adjuster of
the foot.
b) Rotate foot to raise or lower it until it stands firmly on the
ground.
A
c) Lock the foot in position by turning the nut anti-clockwise
until it comes up against the bottom of the machine.
B
C
Ensure that the knob is on the “OFF” position and the load
door is closed
Insert the plug.
ATTENTION:
should it be necessary to replace the supply cord, connect
the wire in accordance with the following colours/codes:
BLUE
- NEUTRAL (N)
BROWN
- LIVE (L)
YELLOW-GREEN
- EARTH (
)
After installation, the appliance must be positioned so that
the plug is accessible.
10
EN
CHAPTER 6
DN
O
F
E
P
G H I C L M
B
A
CONTROLS
Door handle
A
Timer knob for wash programmes with OFF position
Wash Temperature button
B
C
Spin Speed button
D
Degree of soiling button
E
Buttons indicator light
F
Intensive button
G
Aquaplus button
H
Start Delay button
I
Drying programme selection button
L
Start button
M
Door locked indicator light
N
Digital Display
O
P
Detergent drawer
11
EN
DESCRIPTION OF CONTROL
“Kg DETECTOR”
(Function active only on Cotton and Synthetics programmes)
Through every wash phase “Kg DETECTOR” allows to monitor
information on
the wash load in the drum.
So, as soon as the “Kg DETECTOR” is set in motion, in the first 4
minutes of the wash, it:
- adjusts the amount of water required
- determines the length of the wash cycle
- controls rinsing
according to the type of fabric selected to be washed it:
- adjusts the rhythm of drum rotation for the type of fabric
being washed
- recognises the presence of lather, increasing, if necessary, the
amount of water during
rinsing
- adjusts the spin speed according to the load, thus avoiding
any imbalance.
In this way “Kg DETECTOR” is able to decide, by itself, the most
suitable programme for each individual wash from the
hundreds of possible wash combinations.
“Kg DETECTOR” meets the need for easy use by permitting a
simplified programme selection. In
fact, the user need only tell the machine the type of fabric in
the drum and the degree of soiling, to obtain a perfect wash
with the highest
level of drying possible with a spin which really cares for your
clothes.
DOOR HANDLE
Press the finger-bar inside
the door handle to open the door
12
A
EN
PROGRAMME SELECTOR WITH OFF POSITION
B
WHEN THE PROGRAMME SELECTOR IS TURNED THE DISPLAY
LIGHTS UP TO SHOW THE SETTINGS FOR THE PROGRAMME
SELECTED. TODAY, MOST DETERGENTS HAVE BEEN IMPROVED TO
WASH EFFICIENTLY AT LOWER TEMPERATURES, THEREFORE WE
HAVE SET THE DEFAULT TEMPERATURE SETTINGS OF EACH
PROGRAMME TO A LOWER LEVEL, SAVING ELECTRICITY AND
REDUCING THE CARBON FOOTPRINT OF YOUR MACHINE.
YOU CAN SELECT AN HIGH TEMPERATURE BY PRESSING THE
TEMPERATURE BUTTON. PLEASE REFER TO THE PROGRAMME
GUIDE FOR THE MAXIMUM TEMPERATURE TO WHICH EACH
PROGRAMME CAN BE SET.
N.B. TO SWITCH THE MACHINE OFF, TURN THE PROGRAMME
SELECTOR TO THE “OFF” POSITION.
Press the "Start/Pause" button to start the selected cycle.
The programme carries out with the programme selector
stationary on the selected programme till cycle ends.
Switch off the washing machine by turning the selector to OFF.
NOTE:
THE PROGRAMME SELECTOR MUST BE RETURN TO THE
OFF POSITION AT THE END OF EACH CYCLE OR WHEN
STARTING A SUBSEQUENT WASH CYCLE PRIOR TO THE
NEXT PROGRAMME BEING SELECTED AND STARTED.
“WASH TEMPERATURE” BUTTON
C
When a programme is selected the relevant indicator will light
up to show the recommended wash temperature.
The Temperature button can be used to decrease or increase
the temperature of your chosen wash cycle.
Each time the button is pressed, the new temperature level is
shown on the Wash Temperature Indicator.
“SPIN SPEED” BUTTON
The spin cycle is very important to remove as much water as
possible from the laundry without damaging the fabrics. You
can adjust the spin speed of the machine to suit your needs.
By pressing this button, it is possible to reduce the maximum
speed, and if you wish, the spin cycle can be cancelled.
To reactivate the spin cycle is enough to press the button until
you reach the spin speed you would like to set.
For not damage the fabrics, it is not possible to increase the
speed over that automatically suitable during the selection of
the program.
D
It is possible to modify the spin speed in any moment, also
without to pause the machine.
NOTE:
THE MACHINE IS FITTED WITH A SPECIAL ELECTRONIC DEVICE,
WHICH PREVENTS THE SPIN CYCLE SHOULD THE LOAD BE
UNBALANCED. THIS REDUCES THE NOISE AND VIBRATION IN
THE MACHINE AND SO PROLONGS THE LIFE OF YOUR
MACHINE.
13
EN
“DEGREE OF SOILING” BUTTON
By selecting this button (active only on COTTON and MIXED
FIBRES programmes) there is a choice of 3 levels of wash
intensity, depending on how much the fabrics are soiled.
Once the programme has been selected the indicator light
will automatically show the minimum level required for that
programme. Pressing the button increases the duration of the
wash cycle, and adjusts the wash settings accordingly. For
example: Using this button on the Rapid Wash cycle will
enable you to select either a 14, 30 or 44 minute wash cycle.
E
BUTTONS INDICATOR LIGHT
F
These light up when the relevant buttons are pressed.
If an option is selected that is not compatible with the
selected programme then the light on the button first flashes
and then goes off.
The option buttons should be selected before pressing the START
button
INTENSIVE BUTTON
By pressing this button a sensors system come into operation.
They affect both the selected temperature, keeping it at a
constant level throughout the wash cycle, and the
mechanical function of the drum.
The drum is made to turn at two different speeds at crucial
moments. When the detergent enters the garments, the
drum rotates in such a way that the detergent is distributed
in a uniform manner; during the wash and rinse procedures,
however, the speed increases in order to maximise the
cleaning action. Thanks to this special system, the efficiency
of the wash procedure is improved WITHOUT ANY INCREASE
IN THE LENGTH OF THE PROGRAM.
14
G
EN
“AQUAPLUS” BUTTON
By pressing this button you can activate a special new
wash cycle in the Colourfast and Mixed Fabrics programs,
thanks to the new Sensor System. This option treats with
care the fibres of garments and the delicate skin of those
who wear them.
The load is washed in a much larger quantity of water and
this, together with the new combined action of the drum
rotation cycles, where water is filled and emptied, will give
you garments which have been cleaned and rinsed to
perfection. The amount of water in the wash is increased so
that the detergent dissolves perfectly, ensuring an efficient
cleaning action. The amount of water is also increased
during the rinse procedure so as to remove all traces of
detergent from the fibres.
This function has been specifically designed for people with
delicate and sensitive skin, for whom even a very small
amount of detergent can cause irritation or allergy.
You are advised to also use this function for children’s
clothing and for delicate fabrics in general, or when
washing garments made of towelling, where the fibres tend
to absorb a greater quantity of detergent.
To ensure the best performance for your wash, this function
is always activated on the Delicates and
Woollens/Handwash programs.
“DELAY START” BUTTON
This button allows you to pre-programme the wash cycle to
delay the start of the cycle for up to 24 hours.
To delay the start use the following procedure:
Set the required programme.
Press the button once to activate it (h00 appears on the
display) and then press it again to set a 1 hour delay (h01
appears on the display); the pre-set delay increases by 1
hour each time the button is pressed, until h24 appears on
the display, at which point pressing the button again will
reset the delay start to zero.
H
I
Confirm by pressing the “START/PAUSE” button (the light on
the display starts to flash). The countdown will begin and
when it has finished the programme will start automatically.
It is possible to cancel the delay start by taking the following
action:
Press and hold the button for 5 seconds until the display will
show the settings for the programme selected.
At this stage it is possible to start the programme previously
selected by pressing the “START/PAUSE” button or to cancel
the process by setting the selector to the OFF position and
then selecting another programme.
15
EN
DRYING PROGRAMME SELECTION BUTTON
With the programme selector not in the OFF position, press the
button to select the required drying programme; an indicator
will light to display the drying result selected each time you
press the button.
To cancel the selection before the start of a drying programme,
press the button repeatedly until the indicators go out or return
the programme selector to the OFF position.
To cancel the cycle during the drying phase, hold the button
down for 2 seconds until the cooling indicator lights up; given
the high temperature inside the drum, we recommend that you
allow the dryer to complete the cool down period before
returning the programme selector to the OFF position and
removing the laundry.
NOTE:
Do not dry unwashed items in the washer dryer.
Items that have been soiled with substances such as cooking
oil, acetone, alcohol, petrol, kerosene, spot removers, turpentine,
waxes and wax removers should be washed in hot water with
an extra amount of detergent before being dried in the washer
dryer.
Items such as foam rubber (latex foam), shower caps,
waterproof textiles, rubber backed articles and clothes or
pillows fitted with foam rubber pads should not be dried in the
washer dryer.
Fabric softeners, or similar products, should be used as specified
by the fabric softener instructions.
The final part of a washer dryer cycle occurs without heat (cool
down cycle) to ensure that the items are left at a temperature
that ensures that the items will not be damaged.
WARNING:
Never stop a washer dryer before the end of the drying cycle
unless all items are quickly removed and spread out so that the
heat is dissipated.
16
L
EN
START BUTTON
Press to start the selected cycle.
M
NOTE:
FEW SECONDS AFTER THE START THE WASH CYCLE WILL
BEGIN. DURING THE FIRST 4 MINUTES OF THE WASH
CYCLE, THE KG DETECTOR (ACTIVE ONLY ON COTTON
AND SYNTHETICS PROGRAMMES) WILL WEIGH THE
CLOTHES AND UPDATE THE MAXIMUM WASH TIME
REMAINING ON THE DISPLAY EVERY FIVE SECONDS
UNTIL THE WEIGHT HAS BEEN DETERMINED.
WHILE THIS FUNCTION IS OPERATING THE “Kg
DETECTOR” INDICATOR IS ON.
CHANGING THE SETTINGS AFTER THE PROGRAMMES HAS STARTED
(PAUSE)
Press and hold the “START/PAUSE” button for about 2 seconds,
the flashing lights on the options buttons and time remaining
indicator will show that the machine has been paused, adjust
as required and press the “START/PAUSE” button again to
cancel the flashing lights.
If you wish to add or remove items during washing, wait 2
minutes until the safety device unlocks the door.
When you have carried out the manoeuvre, close the door,
press START button and the appliance will continue working
where it left off.
CANCELLING THE PROGRAMME
To cancel the programme, set the selector to the OFF position.
Select a different programme.
Re-set the programme selector to the OFF position.
DOOR LOCKED INDICATOR
The “Door Locked” indicator light is illuminated when the door is
fully closed and the machine is ON.
When START is pressed on the machine with the door closed the
indicator will flash momentarily and then illuminate.
N
If the door is not closed the indicator will continue to flash.
A special safety device prevents the door from being opened
immediately after the end of the cycle. Wait for 2 minutes after
the wash cycle has finished and the Door Locked light has
gone out before opening the door. At the end of cycle turn the
programme selector to OFF .
17
EN
“DIGITAL” DISPLAY
The display’s indicator system allows you to be constantly
informed about the status of the machine:
O
{
{
8
6
{
5
4
{
1
{
2
1) WASH TEMPERATURE
When a programme is selected the relevant indicator will
light up to show the recommended wash temperature. The
Temperature button can be used to decrease or increase
the temperature of your chosen wash cycle. Each time the
button is pressed, the new temperature level is shown on the
Wash Temperature Indicator.
1
2) DOOR LIGHT
Once the START/PAUSE button has been pressed the light first
flashes then stops flashing and remains on until the end of
the wash.
2 minutes after the end of the wash the light goes off to
show that the door can now be opened.
2
3) SPIN SPEED
Once the programme has been selected, the maximum spin
speed allowed for that programme appears on the display.
Pressing the spin button will reduce the speed by 100 rpm
each time the button is pressed. The minimum speed
allowed is 400 rpm, or it is possible to omit the spin by
pressing the spin button repeatedly.
{
3
4
4) DELAY START LIGHT
This flashes when delay start has been set.
18
5
{
5) CYCLE DURATION
When a programme is selected the display automatically
shows the cycle duration, which can vary, depending on the
options selected.
Once the programme has started you will be kept informed
constantly of the time remaining to the end of the wash.
The appliance calculates the time to the end of the selected
programme based
upon a standard loading, during the cycle, the appliance
corrects the time to that applicable to the
size and composition of the load.
If is selected the automatic washing/drying cycle, at the end
of the wash phase, the drying time remaining to the end will
be shown on the display.
{
7
3
h
mm
EN
6
6)Kg DETECTOR Indicator
Available on Cotton and Synthetic cycles, during the first 4
minutes of the cycle the intelligent sensor will weigh the
laundry and adjust the cycle time, water and electricity
consumption accordingly.
}
7) DEGREE OF SOILING
When a programme is selected the relevant indicator will
light up to show the minimum possible degree of soiling.
Selecting a greater degree of soiling using the special
button will cause the corresponding indicator to light up.
The indicators display the type of the drying programme:
Automatic Programmes: By selecting one of these 3
automatic programmes, the washer-dryer will calculate the
time needed for drying and the residual dampness
required, according to the load and drying type selected.
After pressing the START button, the display will shown the
drying time remaining.
8
{
8) DRYING PROGRAMME INDICATORS
7
The appliance calculates the time to the end of the
selected programme based
upon a standard loading, during the cycle, the appliance
corrects the time to that applicable to the
size and composition of the load.
= Extra dry drying programme (recommended
for towels, bathrobes and bulky loads)
= Cupboard dry drying programme
= Iron dry drying programme
USEFUL TIPS:
The 30 minute drying programme is recommended for small
loads (less than 1 kg) or slightly damp loads.
Your washer-dryer ends the cycle automatically when it
reaches the drying level selected.
For the correct operation of the appliance, it is preferable
not to interrupt the drying phase unless it is really necessary.
Timed programmes:
120 minutes – 90 minutes – 60 minutes – 30 minutes:
They may be used to select timed drying programmes.
Cool down phase
:
Switched on during the final cool down period, in the last 10
minutes of each drying phase.
19
TABLE OF PROGRAMMES
PROGRAMME
SELECTOR ON:
PROGRAM FOR:
WEIGHT RECOMMENDED
MAX
TEMP.
kg
°C
MAX TEMP.
°C
CHARGE DETERGENT
2
Resistant fabrics
1)
8
60°
Up to:
90°
●
●
8
40°
Up to:
60°
●
●
4
40°
Up to:
60°
●
●
Very delicate fabrics
2,5
40°
Up to:
40°
●
●
“MACHINE WASHABLE”
woollens
2
40°
Up to:
40°
●
●
Hand wash
1,5
30°
Up to:
30°
●
●
Rinse
-
-
-
-
-
-
Drain only
-
-
-
Mix & Wash
system programme
8
40°
Up to:
40°
●
●
1,5
30°
Up to:
30°
●
●
Resistant fabrics
Mixed fabrics and synthetics
Rapid 30 minute
2,5
30°
Up to:
40°
●
●
Resistant fabrics
Mixed fabrics and synthetics
Rapid 44 minute
3,5
30°
Up to:
40°
●
●
4
40°
Up to:
40°
●
●
4
-
-
5
-
-
1,5
30°
Up to:
30°
●
●
Cotton, linen
with Prewash
*
Cotton, mixed
resistant,
Coloureds
1)
Mixed fabrics and synthetics
Cotton, mixed fabrics, synthetics
1)
Fast spin
Resistant fabrics
Mixed fabrics and synthetics
Rapid 14 minute
Mixed, delicate
synthetics
Mixed - Drying
Cotton - Drying
Cotton - Mixed
20
1
**
*
*
●
*
*
*
2)
*
*
●
Please read these notes
When washing heavily soiled laundry it is recommended the load is reduced to 4 kg maximum.
Information for the test laboratories
(Ref. EN 50229 Standards)
Washing
Use the programme ** with the maximum degree of soiling selected, maximum spin speed
and a temperature of 60°C.
Programme recommended also for test with a lower temperature.
Drying
First drying with 5kg (the load consist: pillowcases and hand-towels) selecting the cotton
drying programme (
) cupboard dry (
).
Second drying with 3kg (the load consist: 3 sheets and hand towels) selecting the cotton
drying programme (
) 120 minutes (120’).
The spin speed may also be reduced, to match any guidelines suggested on the fabric label, or
for very delicate fabrics cancel the spin completely this option is available with a spin speed
button.
Pressing the wash temperature button makes it possible to wash at any temperature below
the maximum allowed.
* Programmes for automatic drying.
1) For the programmes shown you can adjust the duration and intensity of the wash
using the degree of soiling button.
2) Using the Degree of soiling button on the Rapid cycle will enable you to select either a
14, 30 or 44 minute wash cycle.
21
EN
CHAPTER 8
SELECTION
For the various types of fabrics and various degrees of dirt
the washing machine has different programme bands
according to: wash cycle, temperature and lenght of cycle
(see table of washing cycle programmes).
RESISTANTS FABRICS
The programmes have been designed for a maximum wash
and the rinses, with spin intervals, ensure perfect rinsing.
The final spin gives more efficient removal of water.
MIXED AND SYNTHETIC FABRICS
The main wash and the rinse gives best results thanks to the
rotation rhythms of the drum and to the water levels.
A gentle spin will mean that the fabrics become less
creased.
SPECIAL DELICATE FIBRES
This is a new wash cycle which alternates washing and
soaking and is particularly recommended for very delicate
fabrics.
The wash cycle and rinses are carried out with high water
levels to ensure best results.
WOOLMARK PROGRAMME
The special cycle, enables to thoroughly wash garments
without damaging them.
The cycle comprises of alternate periods of activity and
pauses with a maximum temperature of 40°C and concludes
with 3 rinses and a short spin.
22
EN
SPECIAL “HAND WASH”
This washing machine also has a gentle Hand Wash
programme cycle. This programme allows a complete
washing cycle for garments specified as “Hand Wash only”
on the fabric care label. The programme has a temperature
of 30°C and concludes with 3 rinses and a slow spin.
SPECIAL “RINSE” PROGRAMME
This programme carries out three rinses with a intermediate
spin (which can be reduced or excluded by using the
correct button). It can be used for rinsing any type of fabric,
eg. use after hand-washing.
SPECIAL “FAST SPIN” PROGRAMME
Programme “FAST SPIN” carries out a maximum spin (which
can be reduced by using the correct button).
DRAIN ONLY
This programme drains out the water.
“MIX & WASH SYSTEM” PROGRAMME
This is an exclusive Candy system and involves 2 great
advantages for the consumer:
• to be able to wash together different type of fabrics (e.g.
cotton + synthetic etc…) FAST COLOUREDS;
•to wash with a considerable energy saving.
The "Mix & Wash" programme has a temperature of 40°C
and alternate dynamic phases (the basket that turns) to
static phases (fabrics in soak in phase of rest) with a
duration programme that almost reaching the 2 hours.
The energy consumption for the complete cycle is only 850
W/h.
Important:
•the first washing of new coloureds fabrics must be done
separately;
• in every case, never mix NON-FAST COLOUREDS fabrics.
23
EN
RAPID PROGRAMME
The Rapid programme allows a washing cycle to be
completed in just 14 minutes! This programme is particularly
suited to slightly dirty cottons and mixed fabrics.
Using the Degree of soiling button on the Rapid cycle will
enable you to select either a 14, 30 or 44 minute wash cycle.
When selecting the rapid programme, please note that we
recommend you use only 20% of the recommended
quantities shown on the detergent pack.
For information about these programmes please refer to the
programmes table.
“SHIRTS” PROGRAMME
This programme allows a complete washing cycle for shirts.
The main wash and the rinse gives best results thanks to the
rotation rhythms of the drum and to the water levels.
The programme has a maximum temperature of 40°C and
concludes with 3 rinses and a short spin.
SYNTHETICS DRYING
Mixed fabrics (synthetics/cotton), synthetic fabrics.
COTTON DRYING
Cotton, terry towelling, linen, hemp fabrics, etc...
RAPID 59’
A complete express washing and drying cycle lasting only
59'. This is an ideal program for having dry, refreshed and
ready-to-wear clothes as soon as the cycle is finished.
- Maximum load: 1,5 kg (4 shirts for example)
- Lightly soiled fabrics (cotton and mixed fabrics)
With this program we recommend that you reduce the
detergent loading dose (compared to the normal one), in
order to avoid detergent waste.
24
EN
CHAPTER 9
DETERGENT DRAWER
The detergent draw is split into 3 compartments:
- the compartment labelled "1" is for prewash detergent;
- the compartment
✿
labelled “ ” is for special additives, fabric softeners,
fragrances, starch, brighteners etc;
- the compartment labelled "2" is for main wash detergent.
NOTE: SOME DETERGENTS ARE DIFFICULT TO REMOVE.
FOR THESE, WE RECOMMEND YOU USE THE SPECIAL
DISPENSER WHICH IS PLACED IN THE DRUM.
NOTE: ONLY PUT LIQUID PRODUCTS IN THE
COMPARTMENT
LABELLED “✿”. THE MACHINE IS PROGRAMMED TO
AUTOMATICALLY TAKE UP ADDITIVES DURING THE
FINAL RINSE STAGE FOR ALL WASH CYCLES.
25
EN
CHAPTER 10
THE PRODUCT
IMPORTANT:
When washing heavy rugs, bed spreads and other heavy
articles, it is advisable not to spin.
To be machine-washed, woollen garments and other articles
in wool must bear the “Machine Washable Label”.
IMPORTANT:
When sorting articles ensure that:
- there are no metal objects in the washing (e.g. brooches,
safety pins, pins, coins etc.).
- cushion covers are buttoned, zips and hooks are closed,
loose belts and long tapes on dressing gowns are
knotted.
- runners from curtains are removed.
- attention is paid to garment labels.
- when sorting, any tough stains should be removed prior to
washing using stain removers only recommended on
label.
26
EN
CHAPTER 11
CUSTOMER AWARENESS
A guide environmentally friendly and economic use of your
appliance.
MAXIMISE THE LOAD SIZE
Achieve the best use of energy, water, detergent and time by
using the recommended maximum load size.
Save up to 50% energy by washing a full load instead of 2 half
loads.
DO YOU NEED TO PRE-WASH?
For heavily soiled laundry only!
SAVE detergent, time, water and between 5 to 15% energy
consumption by NOT selecting Prewash for slight to normally
soiled laundry.
IS A HOT WASH REQUIRED?
Pretreat stains with stain remover or soak dried in stains in
water before washing to reduce the necessity of a hot wash
programme.
Save up to 50% energy by using a 60°C wash programme.
BEFORE USING A DRYING PROGRAMME...
SAVE energy and time by selecting a high spin speed to
reduce the water content in laundry before using a drying
programme.
27
EN
WASHING
VARIABLE CAPACITY
This washing machine automatically adapts the level of the
water to the type and quantity of washing. In this way it is also
possible to obtain a “personalized” wash from an energy saving
point of view.
This system gives a decrease in energy consumption and a
sensible reduction in washing times.
EXAMPLE:
A net bag should be used for particularly delicate fabrics.
Let us suppose that the washing consists of HEAVILY SOILED
COTTON (tough stains should be removed with suitable
stain removal).
It is advisable not to wash a load made up entirely of
articles in towelling fabric which absorb a lot of water and
become too heavy.
● Open the detergent drawer (P).
● Put 120 g in the main wash compartment marked 2.
● Put 50 ml of the desired additive in the additives
compartment
.
✿
● Close the detergent drawer (P).
● Ensure that the water inlet tap is turned on.
● And that the discharge tube is in place.
PROGRAMME SELECTION
Refer to the programme guide to select the most suitable
programme.
Turning the selector knob required programme is activate.
The display will show the settings for the programme selected.
Adjust the wash temperature if necessary.
Press the option buttons (if required)
Then press the START button.
When the START button is pressed the machine sets the working
sequence in motion.
The programme carries out with the programme selector
stationary on the selected programme till cycle ends.
28
EN
Warning: If there is any break in the power supply while the
machine is operating, a special memory stores the selected
programme and,when the power is restored, it continues where it
left off.
● When the programme has ended the word “End” will appear
on the display
● Wait for the door lock to be released (about 2 minutes after the
programme has finished).
● Switch off the machine by turning the programme selector to
the “OFF” position.
● Open the door and remove the laundry.
● Turn off the water supply after every use.
FOR ALL TYPES OF WASH CONSULT THE PROGRAMME
TABLE AND FOLLOW THE OPERATIONS IN THE ORDER
INDICATED.
29
EN
CHAPTER 12
DRYING
DON’T DRY GARMENTS MADE FROM FOAM RUBBER
OR FLAMMABLE MATERIALS.
IMPORTANT:
THIS DRYER CAN ONLY BE USED FOR LAUNDRY
WHICH HAS BEEN WASHED AND SPIN DRIED.
WARNING:
Indications given are general, therefore some practice is
needed for the best drying results. We recommend setting a
lower drying time than indicated, when first using, so as to
establish the degree of dryness required. We recommend not
to dry fabrics that fray easily, such as rugs or garments with a
deep pile, to avoid air duct clogging.
The water is then conveyed to the drain circuit, wich is sealed
and therefore, no steam can be released outside.
IMPORTANT
NEVER OPEN THE DOOR AFTER THE DRYING CYCLE
HAS BEGUN - WAIT UNTIL THE COOL DOWN PERIOD
PROVIDED FOR BY THE CYCLE.
Only dry pre-spun laundry
The washer/dryer can perform two types of drying:
1 Cotton, terry towelling, linen, hemp fabrics, etc...
Advisory note
During drying phase the drum will accelerate to a higher
speed to
distribute the load and to optimize the drying performance
2 Mixed fabrics (synthetics/cotton), synthetic fabrics.
30
EN
MAX
5 kg
DRYING CYCLE
● Open door.
● Fill with up to 5 kg - in case of large items (e.g. sheets) or
very absorbent items (e.g. towels or jeans), it is a good idea
to reduce the load.
● Close door.
● Turn programme dial to
cotton.
● Select the degree of dryness that you require.
This ranges from Extra Dry (
) for bath towels and
bathrobes, through Cupboard Dry (
) for items that will
be put away without ironing, to iron dry (
) that leaves
the laundry suitable for ironing.
If you wish to select a timed drying cycle, press the “drying
programme selection” button until the required time
indicator lights up.
DOUBLE-SKIN DOOR
The appliance door is fitted with a protective shield to
prevent contact with the glass door which can reach high
temperatures, during the drying cycle.
WARNING: DO NOT TOUCH DOOR FOR ANY REASON.
● Make sure water inlet valve is open.
● Make sure water drain is correctly positioned.
WARNING:
DO NOT DRY WOOLLEN GARMENTS OR ARTICLES WITH
SPECIAL PADDING, (E.G. QUILTS, QUILTED ANORAKS,
ETC.).
DELICATE FABRICS IF GARMENTS ARE DRIP/DRY, LOAD
LESS ITEMS AO AS TO PREVENT CREASING.
31
EN
● Press the START button.
● The drying phase will begin with the programme dial fixed
on the
symbol until the end of drying.
● The drying programme indicator will be on until the cool
down phase will begin and the indicator (
) will go on.
At the end of the programme the word “END” will appear on
the display.
● Wait for the door lock to be released (about 2 minutes after
the programme has finished).
The "Door Security" indicator light will go out.
● Switch off the machine by turning the programme selector
on the “OFF” position.
● Open the door and remove the laundry.
● Turn off the water supply after every use.
32
EN
CHAPTER 13
AUTOMATIC WASHING/DRYING
WARNING: ONLY A MAXIMUM 5 KG OF DRY LAUNDRY
CAN BE LOADED OTHERWISE THE DRIED LAUNDRY WILL
BE NOT SATISFACTORY.
Washing:
Open the drawer, choose the detergent and put in the
correct amount.
Refer to the list of washing programmes according to fabrics
to be washed (e.g. very dirty cotton) and without pressing
Start button, prepare wash as described:
Turning the selector knob, the required programme is
activated.
The display will show the settings for the programme selected.
Adjust the wash temperature if necessary.
Press the option buttons (if required)
Check that the tap is turned on and that the discharge hose
is positioned correctly.
Drying:
Select the degree of dryness that you require.
This ranges from Extra Dry
(
) for bath towels and bathrobes, through Cupboard Dry
(
) for items that will be put away without ironing, to iron
dry (
) that leaves the laundry suitable for ironing.
If you wish to select a timed drying cycle, press the “drying
programme selection” button until the required time
indicator lights up.
Press the "Start/Pause" button.
The programme carries out with the programme selector
stationary on the selected programme till cycle ends.
At the end of the wash phase the display will shown the
drying time remaining.
The washer-dryer will then complete the entire drying
programme.
The drying programme indicator will be on until the cool
down phase will begin and the indicator (
) will go on.
At the end of the programme the word “END” will appear on
the display.
Wait for the door lock to be released (about 2 minutes after
the programme has finished).
The "Door Security" indicator light will go out.
Switch off the machine by turning the programme selector
on the “OFF” position.
Open the door and remove the laundry.
Turn off the water supply after every use.
33
EN
TABLE OF DRYING TIMES (IN MINUTES):
PROGRAMME
Extra
Cupboard
Iron
COTTON
MIXED
Min 1 Kg
Max 5 Kg
Min 1 Kg
Max 4 Kg
from 30’
from 30’
from 30’
to 230’
to 220’
to 170’
from 30’
from 30’
from 30’
to 170’
to 150’
to 80’
The appliance calculates the time to the end of the selected programme based
upon a standard loading, during the cycle, the appliance corrects the time to that
applicable to the size and composition of the load.
34
EN
CHAPTER 14
CLEANING AND ROUTINE MAINTENANCE
Do not use abrasives, spirits and/or diluents on the exterior of
the appliance. It is sufficient to use a damp cloth.
The washing machine requires very little maintenance:
● Cleaning of drawer compartments.
● Filter cleaning
● Removals or long periods when the machine is left
standing.
CLEANING OF DRAWER COMPARTMENTS
Although not strictly necessary, it is advisable to clean the
detergent, bleach and additives compartments
occasionally.
Remove the compartments by pulling gently.
Clean with water.
Put the compartments back into place
35
EN
FILTER CLEANING
The washing-machine is equipped with a special filter to
retain large foreign matter which could clog up the drain,
such as coins, buttons, etc. These can, therefore, easily be
recovered. The procedures for cleaning the filter are as
follows:
● Open the flap
● Only available on certain models:
Pull out the corrugated hose, remove the stopper and drain
the water into a container.
● Before removing the filter, place an absorbent towel below
the filter
cap to collect the small amount of water likely to be inside
the pump
● Turn the filter anticlockwise till it stops in vertical position.
● Remove and clean.
● After cleaning, replace by turning the notch on the end of
the filter clockwise. Then follow all procedures described
above in reverse order.
REMOVALS OR LONG PERIODS WHEN THE MACHINE IS LEFT
STANDING
For eventual removals or when the machine is left standing
for long periods in unheated rooms, the drain hose should be
emptied of all remaining water.
The appliance must be switched off and unplugged. A bowl
is needed. Detach the drainage hose from the clamp and
lower it over the bowl until all the water is removed.
Repeat the same operation with the water inlet hose.
36
EN
CHAPTER 15
FAULT
REMEDY
CAUSE
Mains plug not plugged in
Insert plug
Mains switch not on
Turn on mains switch
No power
Check
Electric circuit fuses failure
Check
Load door open
Close load door
See cause 1
Check
Inlet tap turned off
Turn on water inlet tap
Timer not set correctly
Set timer on correct position
Discharge tube bent
Straighten discharge tube
Odd material blocking filter
Check filter
4. Water on floor
around washing
machine
Leak from the washer between the tap
and inlet tube
Replace washer and tighten the tube
on the tap
5. Does not spin
The washing machine has not
discharged water
Wait a few minutes until the machine
discharges water
“No spin” setting (some models only)
Turn the programme dial onto spin
setting
Washing machine not perfectly level
Adjust special feet
Transport bracket not removed
Remove transport bracket
Washing load not evenly distributed
Distribute the washing evenly
1. Does not function
on any
programme
2. Does not load
water
3. Does not
discharge water
6. Strong vibrations
during spin
–
7. Display reads error
0, 1, 5, 7, 8, 9
Call service.
8. Display reads
error 2
No water fill.
Check water supplies are on.
9. Display reads
error 3
No pump out.
Check drain is clear.
Check drain hose is not kinked.
10. Display reads
error 4
Machine overfilled with water.
Turn off water supply to machine.
Call service.
Advisory note
During drying phase the drum will accelerate to a higher speed to distribute the load and to
optimize the drying performance
37
If the fault should persist, contact a Candy Technical Assistance Centre. For prompt servicing, give
the model of the washing machine, to be found on the label placed on the cabinet inside of the
porthole or on the guarantee certificate.
Important
1 The use of environment friendly detersives without phosphates may produce the following
effects:
- The discharge rinse water may result cloudier due to the presence of zeolites in suspension.
This does not compromise the efficiency of the rinses.
- The presence of white powder (zeolites) on the washing at the end of the washing cycle. This
does not remain incorporated in the fabric and does not alter the colour.
- The presence of foam in the last rinse water which is not necessarily a sign of inadequate
rinsing.
- The non-ionic surface-active agents present in the composition of washing machine
detersives are often difficult to remove from the washing itself and, even in small quantities,
may produce visible signs of the formation of foam.
- Carrying out further rinses, in cases such as this, is not useful.
2 If your washing machine fails to function, carry out the above-mentioned checks before calling
the Candy Technical Assistance Service.
38
The manufacturer declines all responsibility in the event of any printing mistakes in
this booklet. The manufacturer also reserves the right to make appropriate
modifications to its products without changing the essential characteristics.
This appliance is marked according to the European directive 2002/96/EC on Waste Electrical and Electronic
Equipment (WEEE).
By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the
environment and human health, which could otherwise be caused by inappropriate waste handling of this product.
The symbol on the product indicates that this product may not be treated as household waste. Instead it shall be
handed over to the applicable collection point for the recycling of electrical and electronic equipment
Disposal must be carried out in accordance with local environmental regulations for waste disposal.
For more detailed information about treatment, recovery and recycling of this product, please contact your local city
office, your household waste disposal service or the shop where you purchased the product.
10.02 - 41034477 - www.graficaestampa.it - Printed in Italy - Imprimé en Italie
EN
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising