Frigidaire | FFPH1222U1 | Owner's Guide | Frigidaire FFPA0822U1 Complete Owner's Guide

Frigidaire FFPA0822U1 Complete Owner's Guide
Important Safety Instructions..............................2-3
Air Conditioner Features.....................................8
Product Registration...............................................4
Operating Instruction......................................8-16
Normal Sounds.......................................................4
Care and Cleaning.............................................17
Unit Description......................................................5
Before You Call..................................................18
Accessories Included.............................................5
Major Appliance Limited Warranty................. ...19
Installation Instructions.......................................6-7
Important Safety Instructions
NOTE:
NOTE:
WARNING
WARNING
WARNING
WARNING
SAFETY PRECAUTIONS
Important Safety Instructions
SAFETY PRECAUTIONS
Provide ventilation per installation instructions.
Do not direct airflow at fireplaces or other heat related sources as this could cause flare ups or make units run excessively.
NOTE:
fails
manufacturer.
manufacturer.
Product Registration & Normal Sounds
Product Registration
Record Your Model and Serial Numbers
Record in the space provided below the mode and serial numbers. On all models, the
serial plate is located on the side of the cabinet.
Model No.
Serial No.
Register Your Product
The self-addressed PRODUCT REGISTRATION CARD should be filled in completely,
signed and returned to the Frigidaire Company.
Normal Sounds
Sound of Rushing Air
At the top of the unit, you may
hear the sound of rushing air
being moved by the fan.
Gurgle/Hiss
High pitched Chatter
Today’s high efficiency
compressors may have a
high pitched chatter during
the cooling cycle.
“Gurgling or hissing” noise may be
heard due to refrigerant passing
through evaporator during normal
operation.
Vibration
Unit may vibrate and make noise
because of uneven floor.
Unit Description & Accessories Included
Unit Description
Air Outlet Grill
Control Panel
Carrying
Handle
Signal
Receiver
Air
Exhaust
Remote
Control
Continuous
Drain Outlet
Air Intake
Power
Cord
Castor
Bottom
Drain Outlet
Accessories Included
PARTS:
PARTS NAME:
QUANTITY:
Window Kit Connector A
Exhaust hose connector B
Window Kit
Exhaust Hose
Screws
Safety Lock
Bolts
Foam seal A
Foam seal B
Remote Control
Battery
Drain hose
(
(
+
)
)
Installation Instructions
Installation Instructions
EXHAUSTING HOT AIR
In the Cool Mode the appliance must be placed close to a
window or opening so that the warm exhaust air can be ducted
outside.
First position unit on a flat floor and is within the vicinity of a single
circuit outlet power source. Make sure there’s a minimum of 23.6"
clearance in the front/back of the unit, and a minimum of 19.7"
clearance in the left/right sides of the unit.
Extend the side of hose
1. Extend both side of the exhaust hose(Fig.1)
2. Install the connector B into the unit (Fig.2).
3. Affix the connector A into the window slider kit and seal.
(Fig.3&4)
Fig.1
1 Slide onto
2 Lock
Fig.2
Vertical
window
Horizontal
window
Window Slider Kit
Minimum:26.6Ǝ(67.5cm)
Maxmum:48.5Ǝ(123cm)
Fig.3
Window Slider Kit
Minimum:26.6Ǝ(67.5cm)
Maxmum:48.5Ǝ(123cm)
7KHKRVHFDQEHH[WHQGHGIURPLWVRULJLQDOOHQJWKRIƎuSWRƎ,but it is the best to keep the length to
minimum required. Also make sure that the hose does not have any sharp bends or sags.(Fig.5)
Fig.5
Fig.4
Installation Instructions
Installation Instructions(continued)
Installation in a double-hung sash window
1.Cut the foam seals A(adhesive type) to the proper lengths and attach
them to the window and stool.(Fig.6)
2.Open the window sash and place the window slider kit on the window
stool (Fig.7). Attach the window slider kit to the window stool. Adjust
the length of the window slider kit according to the width of window.
Screw down the two screws on the window slider kit. See Fig.7.
Cut the adjustable window slider kit if the width of window is less than
26.6 inches(Fig.8).
3.Close the window sash securely against the window slider kit.(Fig.9)
'ULYHWZRƎVFUHZVWRVHFXUHWKHZLQGRZVOLGHUNLWWRWKHZLQGRZ
sash.(Fig.9)
5.Secure the window slider kit to the window stool(Fig.9):
$)RUZRRGHQZLQGRZ8VHƎVFUHZVIRUVHFXULQJ
%)RU9LQ\O&ODGZLQGRZV8VHƎKH[KHDGFDSVFUHZVIRU
securing.
Foam seal A
(adhesive type)
Fig.6
screws
Window slider kit
Fig.7
Window stool
Cut this to fit your window
7RVHFXUHORZHUVDVKLQSODFHDWWDFKULJKWDQJOHVDVKORFNZLWKƎ
(12.7mm) screw as shown(Fig.10).
NOTE: It is difficult to lock the windows with the sash lock for Vinyl-Clad
windows, so you can use lock by window itself.
7.Cut the foam seal B to an appropriate length and seal the open gap
between the top window sash and outer window sash, as shown in
Fig.11.
Fig.8
Foam seal A
(adhesive type)
screws
Fig.12
Fig.10
Window slider kit
Foam seal B
screws or
hex head cap screws
Window stool
Window stool
Window slider kit
screws
Fig.11
Fig.9
Installation in a sliding sash window
1.Cut the foam seals A(adhesive type) to the proper lengths and attach
them to the window frame. See Fig.12.
2.Open the window sash and place the window slider kit on the window
stool (Fig.13). Attach the window slider kit to the window stool. Adjust
the length of the window slider kit according to the height of window.
Screw down the two screws on the window slider kit. See Fig.13.
Cut the adjustable window slider kit if the height of window is less than
26.6 inches(Fig.8).
3.Close the window sash securely against the window slider kit.(Fig.14)
'ULYHWZRƎVFUHZVWRVHFXUHWKHZLQGRZVOLGHUNLWWRWKHZLQGRZ
sash.(Fig.14)
'ULYHWZRƎVFUHZVWRVHFXUHWKHZLQGRZVOLGHUNLWWRWKHZLQGRZ
stool.(Fig.14)
6.Cut the foam seal B to an appropriate length and seal the open gap
between the sliding sash and outer window sash, as shown in Fig.15.
7RVHFXUHVOLGLQJVDVKLQSODFHDWWDFKULJKWDQJOHVDVKORFNZLWKƎ
(12.7mm) screw as shown(Fig.16).
Fig.13
Window stool
screws
Window slider kit
screws
Fig.14
Foam seal B
Fig.15
Fig.16
Air Conditioner Features & Operating Instructions
Control Panel
Display Temperature/Timer
°C
°F
Swing
Timer
Sleep
Mode
Selection*
Adjust
Temperature
or Timer
Fan
Speed
Filter Power
Reset RQÂRII
*Note: “heat” mode is for heat & cool models only.
Operating Instruction
Cool mode
Press the “mode” button until the Cool mode indicator lights.
Press the "fan speed" button to choose the fan speed according to the illumination of the fan speed indicator.
You can choose the “hi”, “med”, “low”, or “auto” fan speed setting.
Press the “ ” or “ ”button to choose the temperature you want.
°C
°F
Operating Instructions
Dry mode
Press the “mode” button until the Dry mode indicator lights. In this mode, the “ ” or “ ” button is disabled and
the screen displays the room temperature. The unit will continuously drain moisture from the room.
Note: In this mode, the fan speed will be set as “low” automatically, which cannot be changed.
°C
°F
Fan mode
Press the “mode” button until the Fan mode indicator lights.
In this mode, you can select fan speed “hi”, “med” or “low”.
The screen displays room temperature.
Note: In this mode, the air exhaust hose does not need to be connected.
°C
°F
Heat mode(For Heat & Cool models only)
Press the “mode” button until the Heat mode indicator lights.
Press the “ ” or “ ”button to choose the temperature you want.
At the same time, the “low” fan indicator lights.
°C
°F
Note:
In this mode, fan speed cannot be selected.
Operating Instructions
AUTO mode
Press the “mode” button until the AUTO mode indicator lights.
Press the “ ” or “ ” button to choose the temperature you want. The screen will display the setting temperature.
In this mode, the unit will automatically select cooling, heating(not applicable for cooling only models), or fan only
operation depending on what temperature you have selected and the room temperature. The air conditioner will
control room temperature automatically round the temperature point set by you.
Note: In this mode, fan speed cannot be selected.
°C
°F
Timer mode
The timer facilitates the user to delay the unit startup or shutdown.
How to delay startup
Plug in the unit, so the unit turns to standby.
Press the “timer” button, then the Timer indicator and number of hours on the screen will light.
Tap or hold the UP arrow ( ) or the DOWN arrow ( ) to change delay start timer at 0.5 hour increments up
to 10 hours, then at 1 hour increments up to 24 hours.
After 5 seconds, the setting will be confirmed automatically and the control will count down the time remaining until startup.
The unit will start up in the mode as previously set. Press the “timer” button again within 5 seconds, you will quit the timer
setting directly.
To cancel the setting, press the “timer” button again will show the remain time and press the button again to quit the function.
°C
°F
How to delay shutdown
You can delay shutdown when the unit is on.
Press the “timer” button, then the Timer indicator and number of hours on the screen will light.
Tap or hold the UP arrow ( ) or the DOWN arrow ( ) to change delay shutdown timer at 0.5 hour increments up
to 10 hours, then at 1 hour increments up to 24 hours.
After 5 seconds, the setting will be confirmed automatically and the control will count down the time remaining until
shutdown. Press the “timer” button again within 5 seconds, you will quit the timer setting directly.
To cancel the setting, press the “timer” button again will show the remain time and press the button again to quit the function.
°C
°F
Operating Instructions
Sleep mode
When the unit is in Cool, Heat or Auto mode, you can press the “sleep” button to make the unit run in Sleep mode.
In this mode, the fan speed will be set as “auto” automatically, which cannot be changed.
In Cool/Heat mode the selected temperature will increase/decrease by 2 °F 30 minutes after the mode is selected.
The temperature will then increase/decrease by another 2 °F after an additional 30 minutes. This new temperature
will be maintained for 7 hours before it returns to the originally selected temperature. This ends the "Sleep" mode
and the unit will continue to operate as originally programmed.
The "Sleep" mode program can be cancelled at any time during operation by pressing the "Sleep", “mode”, “fan speed”
RU³RQÂRII´EXWWRQ
Note: In Fan or Dry mode, Sleep mode cannot be set.
°C
°F
Louver Swing Function
Press the “swing” button to enable louver swing function, the swing indicator will illuminate and the louver on the top
panel will swing up and down. Press this button again to disable the louver swing function.
°C
°F
Filter reset
This feature is a reminder to clean the Air Filter (See Care and Cleaning) for more efficient operation.
The filter indicator will illuminate after 250 hours of fan operation. Press the “filter reset” button, to reset after cleaning
the filter.
°C
°F
function
Press the “ ” and “ ”button the same time for more than 3 seconds to switch between degree Fahrenheit and
degrees Celsius.
Note: Under Dry/Fan mode, you can not select °F/°C.
Operating Instructions
Remote Control
Cool Only models
Remote Control screen
Temp/Timer setting button
Mode button
Timer button
Heat and Cool models
RQÂRIIEXWWRQ
Fan Speed button
Swing button
Sleep button
Battery Installation and Important Instructions
Remove the cover at the back of the remote control.
Insert the provided batteries correctly(see the instructions
inside the battery compartment).
Close up the cover.
To replace the old batteries(which have been used up)
with two new R03 “AAA” 1.5V batteries, repeat the
steps above.
Fig.17
If the remote control unit is replaced or discarded, the batteries must be removed and disposed of in
accordance with local legislation as they do harm to the environment.
Do not mix old and new batteries.
Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries.
Do not dispose of batteries in fire. Batteries may explode or leak. If the remote control is not used for a
long time, remove the batteries from the remote control.
The remote control must be handled with extreme care. Do not drop it or expose it to direct sunlight
or sources of heat.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Fig.18
Point the remote control at the location of the signal receiver.
The remote control must be no more than 16 ft(5 meters)
away from the unit (without obstacles between the remote
control and the unit).
User
Remote Control
Portable AC
Operating Instructions
How to Use the Remote Control
TURNING THE UNIT ON
Plug in the unit, then press the “onÂoff” button (when turned on, the unit will operate as the last setting
before shutdown.
7RVZLWFKWKHXQLWRIISUHVV³RQÂRII´EXWWRQDJDLQWKHQUHPRYHWKHSOXJ
Do NOT switch the unit off by removing the plug.
$OZD\VVZLWFKWKHXQLWRIIE\SUHVVLQJWKH³RQÂRII´EXWWRQDQGZDLWIRUIHZPLQXWHVEHIRUHUHPRYLQJWKHSOXJ
Cool mode
Press the “mode” button until the left side of LCD
screen displays “cool”.
Press the “ fan speed” button to choose the fan speed
“auto”, “high”, “mid”, and “low”.
Press the “
” and “
”button to choose the temperature you want.
Dry mode
Press the “mode” button until the left side of LCD screen displays “dry”.
In this mode, the “ ” or “ ” button is disabled and the screen will remain
blank. The unit will continuously drain moisture from the room.
Note: In this mode, the fan speed will be set as “low” automatically, which
cannot be changed.
Fan mode
Press the “mode” button until the left side of LCD
screen displays “fan”.
In this mode, you can select fan speed “high”, “mid”, “low” by pressing
the Fan speed button and referring to the diagram.
Note: In this mode, the air exhaust hose does not need to be connected.
Operating Instructions
Heat mode(For Heat & Cool models only)
Press the “mode” button until the left side of LCD
screen displays “heat”.
Press the “ ” and “ ” button to choose the temperature you want.
At the same time, the “low” fan indicator lights.
Note: In this mode, fan speed will remain in “low” no matter what speed
you choose in the remote control.
Auto mode
Press the “mode” button until the left side of LCD
screen displays “auto”.
Press the “ ” and “ ” button to choose the temperature you want.
In this mode, the unit will automatically select cooling, heating(not applicable for
cooling only models), or fan only operation depending on what temperature you
have selected and the room temperature. The air conditioner will control room
temperature automatically round the temperature point set by you.
Note: In this mode, fan speed cannot be selected.
Sleep mode
When the unit is in Cool, Heat or Auto mode, you can press the “sleep” button
to make the unit run in Sleep mode. In this mode, the fan speed will be set as “auto”
automatically, which cannot be changed.
In Cool/Heat mode the selected temperature will increase/decrease by 2 °F 30
minutes after the mode is selected. The temperature will then increase/decrease by
another 2 °F after an additional 30 minutes. This new temperature will be maintained
for 7 hours before it returns to the originally selected temperature. This ends the
"Sleep" mode and the unit will continue to operate as originally programmed.
The "Sleep" mode program can be cancelled at any time during operation by
SUHVVLQJWKH6OHHS³PRGH´³IDQVSHHG´RU³RQÂRII´EXWWRQ
Note: In Fan or Dry mode, Sleep mode cannot be set.
Louver Swing Function
Press the “swing” button to enable louver swing function,
and the upper side of screen will display “
”. The louver
on the top panel will swing up and down.
Press this button again to disable the louver swing function.
Fig.19
Operating Instructions
function
Press the “ ” and “ ”button the same time for more than 3 seconds to switch
between degree Fahrenheit and degrees Celsius.
Note: Under Dry/Fan mode, you can not select °F/°C.
Timer mode
How to delay startup
Plug in the unit, so the unit turns to standby.
Press the “timer” button, when the unit is off. The screen will display “timer” and “h”,
and the “on” will flashing. Tap or hold the UP arrow " " or the DOWN arrow " " to
change delay start timer at 0.5 hour increments up to 10 hours, then at 1 hour
increments up to 24 hours. After 3 seconds, the timer function is enabled, then
“on” will stop flashing, the display will show the temperature back and the control
will count down the time remaining until startup. The unit will start up in the mode as
previously set.
To cancel the setting, press the “timer” button again. You can also cancel the setting
E\SUHVVLQJWKH³RQÂRII´EXWWRQ
How to delay shutdown
You can delay shutdown when the unit is on.
Press the “timer” button, when the unit is on. The screen will display “timer”and “h”,
and the “off ” will flashing. Tap or hold the UP arrow “ ” or the DOWN arrow “ ” to
change delay shutdown timer at 0.5 hour increments up to 10 hours, then at 1 hour
increments up to 24 hours. After 3 seconds, the timer function is enabled, then
“off ” will stop flashing, the display will show the temperature back and the control
will count down the time remaining until shutdown.
To cancel the setting, press the “timer” button again. You can also cancel the setting
E\SUHVVLQJWKH³RQÂRII´EXWWRQ
Fault Code
If the screen on the unit displays
“AS”, the room temperature sensor
has failed. Contact your Authorize
Frigidaire Service Center.
If the display reads "E4" , the communication
between display PCB and main control PCB
is faulty. Contact your Authorized Frigidaire
Service Center.
If the screen on the unit displays
“ES”, the pipe temperature sensor
has failed. Contact your Authorize
Frigidaire Service Center.
If the screen on the unit displays “P1”, the water
collection tank inside the unit should be full.
Refer to the "Drainage Instructions" on Page 16
for more instructions to drain the successive
condensate. If error repeats, contact your
Authorize Frigidaire Service Center.
Operating Instructions
Drainage Instructions
Continuous Drainage
During the Dry mode, you will need a garden hose (sold separately) to drain the condensate from the unit.
Follow the steps below:
Unscrew the drain cap of continuous drain outlet(Fig.20).
Connect one end of the garden hose (sold separately) to the drain outlet then lead the other end into
a drain that is lower than the unit(Fig.21).
Figure 20
Figure 21
NOTE
Condensate may flow out after removing the drain cap, if the unit is running in Cool or ECO mode.
When you want to remove the garden hose, prepare a drip tray (not supplied) to collect the
condensate from the drain outlet.
Please be sure that the height of the drain and section of the drain hose should not be higher than
that of the drain outlet, or the continous drainage may not work properly.
During Cool or ECO mode, it is recommended to disable continuous drainage by replacing the
drain cap to the drain outlet, to reach the maximum performance.
Figure 22
Figure 23
Emptying the condensate residue inside the unit during winter storage.
Put a drip tray (not supplied) under the continuous drain outlet, then
unscrew the drain cap to allow the condensate to flow into the drip tray.
Replace the drain cap to the continuous drain outlet when no
condensate flows out.
Put the drip tray under the bottom drain outlet, then remove the
rubber stopper from the drain outlet, to allow the condensate to flow
into the drip tray. If your drip tray can’t hold all the condensate, a
number of fills will be needed.
Replace the drain cap to the bottom drain outlet when no
condensate flows out.
Note: To ensure all condensate residue has been removed, tilt the unit
by lifting it slightly upwards from the front until no more condensate
comes out from the drain outlet.
Figure 24
Bottom
Drain Outlet
Drip tray
Care and Cleaning
Cleaning
Clean your air conditioner occasionally to keep it looking new.
Be sure to unplug the unit before cleaning to prevent shock or
fire hazards.
CLEANING THE UNIT
The cabinet and front may be dusted with an oil-free cloth
or washed with a cloth dampened in a solution of warm water and
mild liquid dishwashing detergent.
Never use harsh cleaners, wax or polish on the cabinet front.
Be sure to wring excess water from the cloth before wiping around
the controls. Excess water in or around the controls may cause
damage to the air conditioner.
Remove
screw
CLEANING THE FILTERS
To keep your air conditioner working efficiently, you should
clean the filters every week of operation.
This unit has two filters, they are filter A and B. Grasp the upper panel
tab and take off the filter A which behind the grill of the back panel (Fig.25).
Remove the lower filter B by loosening the screw. Take down the air inlet
grille, then remove the air filter as shown in Fig.25.
Wash the filter using liquid dishwashing detergent and warm water.
Rinse filter thoroughly. Gently shake excess water from the filter. Be
sure filter is thoroughly dry before replacing.
Or, instead of washing you may vacuum the filter clean.
Replace the filter after the filter is dry.
Take down filter
Figure 25
Winter Storage
If the air conditioner will not be used for an
extended period of time:
Before using the air conditioner again:
1.Drain the water collection tank completely
and leave the bottom drain cap and rubber plug
long time enough to allow any residual water to
drain out. Once the tank is completely drained
and no more water flows out, reinstall the rubber
plug and cap.
2.Remove and clean the filter, allow it to dry
completely, then reinstall it.
3.Remove the batteries from the remote control.
4.Store the air conditioner in a cool, dry
location, away from direct sunlight, extreme
temperature, and excessive dust.
1.Make sure the filter and drain cap are in place.
2.Check the cord to make sure it is in good
condition, without cracks or damage.
3.Place new batteries in the remote control.
4.Install the air conditioner as described in the
Installation Instructions.
Before You Call
Major Appliance Limited Warranty
failures.
factory.
10200 David Taylor Drive
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising