GE | PVM9179EFES | Installation Template Rear Wall | GE CSA1201RSS Installation Template Rear Wall

GE CSA1201RSS Installation Template Rear Wall
49-40177SPv03 2/1/01 11:33 AM Page 1
1/4² hasta el extremo
NOTA: ES MUY IMPORTANTE
12²
LEER Y SEGUIR LAS DIRECCIONES
EN LAS INSTRUCCIONES DE
INSTALACIîN ANTES DE PROCEDER
CON ESTA PLANTILLA DE PARED
POSTERIOR.
Esta plantilla es para localizar el corte de escape
horizontal. No use esta plantilla para escape de
recirculaci—n o vertical.
4²
1. Coloque la plantilla de manera plana contra la
pared posterior, alineando los c’rculos A. y B. con
F. CORTE PARA EL ESCAPE
HORIZONTAL EXTERNO
los agujeros correspondientes previamente perforados
CORTE EL AGUJERO A TRAVƒS DE LA PARED POSTERIOR PARA EL ADAPTADOR DE ESCAPE
en la pared posterior para los agujeros A y B del plato
de la pared.
2. Con la plantilla alineada en los agujeros, pegue con
A.
cinta adhesiva la plantilla a la pared posterior.
B.
3. Use un sable o una sierra de agujero para cortar el
‡rea sombreada F. a travŽs de la pared posterior.
ALêNEE CON
LOS AGUJEROS
PREVIAMENTE
4. Remueva la plantilla de la pared posterior.
ALêNEE CON
5. REGRESE Y PROCEDA CON LAS
LOS AGUJEROS
INSTRUCCIONES DE INSTALACêON.
PRECAUCIîN Ð SI EL ADAPTADOR DE ESCAPE ESTç COLOCADO MçS
PERFORADOS
ALLç DE LAS DIMENSIONES RECOMENDADAS, AIRE CARGADO CON
Turn over for English.
PREVIAMENTE
PERFORADOS
GRASA SE DESCARGARç HACIA LA ESTRUCTURA DE LA CASA.
Parte No. 164D3370P166
Pub. No. 49-40177
4922W5A024A
1-01 JR
Impreso in Corea
PLANTILLA DE PARED POSTERIOR
49-40177ENv02 2/1/01 11:32 AM Page 1
1/4² TO EDGE
NOTE: IT IS VERY IMPORTANT TO
12²
READ AND FOLLOW THE DIRECTIONS
IN THE INSTALLATION INSTRUCTIONS
BEFORE PROCEEDING WITH THIS
REAR WALL TEMPLATE.
This template is for locating the horizontal exhaust
cutout. Do not use this template for vertical or
recirculation exhaust.
1. Place the template flat against the rear
wall, aligning the circles A. and B. with the
corresponding holes previously drilled in the
4²
F. CUT OUT FOR HORIZONTAL
OUTSIDE EXHAUST
rear wall for holes A and B of the wall plate.
2. With the template aligned to the holes, tape the
CUT HOLE THROUGH REAR WALL FOR EXHAUST ADAPTOR
template to the rear wall.
3. Use a saber or keyhole saw to cut out the shaded
A.
area F. through the rear wall.
B.
4. Remove the template from the rear wall.
5. RETURN TO AND PROCEED WITH THE
LINE UP WITH
INSTALLATION INSTRUCTIONS.
LINE UP WITH
PREVIOUSLY
PREVIOUSLY
DRILLED HOLE.
Darle vuelta a la hoja para consultar la
versi—n en Espa–ol.
Part No. 164D3370P166
DRILLED HOLE.
CAUTION Ð IF EXHAUST ADAPTOR IS POSITIONED OUTSIDE
RECOMMENDED DIMENSION, GREASE LADEN AIR WILL
DISCHARGE INTO HOUSE STRUCTURE.
Pub. No. 49-40177
4922W5A024A
1-01 JR
Printed in Korea
REAR WALL TEMPLATE
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising