GE | JKP85BABB | Installation instructions | GE JKP85WAWW Installation Instructions

GE JKP85WAWW Installation Instructions
Installation
Instructions
27” Built In Wall Oven
W/Microwave
JKP85
“If you have questions, call 800-GE-CARES or visit our website at
www.GEAppliances.com”
CAUTION: Before you begin- read these
instructions completely and carefully.
• IMPORTANT- Save these instructions for
local inspector’s use.
• IMPORTANT-OBSERVE ALL GOVERNING
CODES AND ORDINANCES.
• Note to Installer- Be sure to leave these
instructions with the Consumer.
• Note to Consumer- Keep these instructions
for future reference.
• Installation of this Built-In Wall Oven w/
Microwave requires basic mechanical and
electrical skills. Proper installation is the
responsibility of the installer. Product failure
due to improper installation is not covered
under the GE Applicance Warranty.
Parts Included
Materials Needed
Wire Nuts
Bottom Trim
Strain Relief
Clamp
8 screws (double)
Tools You Will Need
1/8” Drill Bit &
Electric or
Hand Drill
Pub. No. 31-10462
229C4053P430
Phillips
Screwdriver
1
Junction
Box
36” of String
Installation Instructions
IMPORTANT SFETY INSTRUCTIONS
For Your Safety
Electrical
Requirements
• Be sure your oven is installed properly by a
qualified installer or service technician.
• Be sure the oven is securely installed in a
cabinet that is firmly attached to the house
structure. Weight on the oven door could
cause the oven to tip and result in injury.
Never allow anyone to climb, sit, stand or
hang on the oven door.
• Make sure the cabinets and wall coverings
around the oven can withstand the
temperatures (up to 200°F.) generated by the
oven.
This appliance must be supplied with the
proper voltage and frequency, and connected
to an individual properly grounded branch
circuit, protected by a circuit breaker or fuse
having amperage as noted on rating plate.
(Rating Plate is located on the wall inside the
microwave oven.)
We recommend you have the electrical wiring
and hookup of your oven connected by a
qualified electrician. After installation, have the
electrician show you where your main oven
disconnect is located.
Check with your local utilities for electrical
codes which apply in your area. Failure to wire
your oven according to governing codes could
result in a hazardous condition. If there are not
local codes, your range must be wired and
fused to meet the requirements of the National
Electrical Code, ANSI/NFPA No. 70-Latest
Edition. You can get a copy by writing:
National Fire Protection Association
Battery March Park
Quincy, MA 02269
Effective January 1, 1996, the National
Electrical Code requires that new, but not
existing, construction utilize a 4 conductor
connection to an electric range. When
installing an electric range in new construction,
follow the instructions in NEW
CONSTRUCTION AND FOUR CONDUCTOR
BRANCH CIRCUIT CONNECTION.
You must use a three-wire, single-phase AC
208Y/120 Volt or 240/120 Volt, 60 hertz
electrical system. If you connect to aluminum
wiring, properly installed connectors approved
for use with aluminum wiring must be used.
CAUTION: The electrical power
to the oven supply line must be
shut off while line connections
are being made. Failure to do so
could result in serious injury or death.
2
Installation Instructions
Pre- Installation Checklist
Remove the Oven Door
Remove packaging materials.
Open the oven door to the stop broil position.
Check inside microwave, behind
hinges, and under false bottom.
Remove labels on door, plastic on trims
and panel, and all tape around oven.
DO NOT LIFT THE
DOOR BY THE
HANDLE!
Open oven door and remove literature
prepack, broiler pan and grid, and
oven racks. Open microwave door
and remove shelves and turntable
package.
Grasp the door on both sides and lift
up and off the hinges.
NOTE:The oven door is very
heavy. Be sure you have a
firm grip before lifting the
oven door off the hinges. Use
caution once the door is
removed. Do not lay the door
on its handle. This could
cause dents or scratches.
Oven Racks
EASY
INSTA
LLAT
EASY INSTALLATION
OF
IONYOUR NEW
30"
WALL
30" WALL
OVENOF YOUR
OVEN
NEW
Broiler Pan
and Grid
Before
you
IMPORTA
begin-Rea
IMPORTA NTd these
Save
Note
NTthese
instruction
OBSERVE instruction
to InstallerOWNERBefore
you begin-Read
these instructions completely
and carefully.
s completel
ALL
Be sure
s for inspector's
NoteKeep
IMPORTANTSave these
instructions
for local
use.
GOVERNI
local
these
y and
This
to leave
inspector'
appliance ALL
IMPORTANT- OBSERVE
GOVERNING
CODES
AND
ORDIANCES.
NG
instruction
carefully.
CODES
these
s use.
Note to Installer- Be suremust
to leave these
instructions
with
the consumer.
instruction
s
AND
be for for
future
OWNER- Keep these instructionsproperly
future
reference. s withORDIANC
reference.
FOR
ES.
grounded
the
YOUR
Note- This
appliance must be properly grounded
(if applicable).
consumer
SAFETY
(if applicable
Before
.
you
instruction
begin-Rea
).
carefully. s completel d
FOR YOUR SAFETYthese
ELECTRICAL REQUIREMENTS
IMPORTA
y and
ELECTRIC
instructionNTBefore youSave
begin-Read these
AL REQUIREM
Before you begin-Read
these
IMPORTA
these
s for
Before
instructions
completely and
local
instructions
completely and
GOVERNI
NTyou
inspector'
ENTS
OBSERVE
instruction
carefully.begin-Rea
Note carefully.
NG
CODES
carefully. s completel d
to InstallerSave ALL
these s use.
these IMPORTANTIMPORTANT- Save these
these
AND
IMPORTA
instruction
instructions
local inspector's use.
Befor
y and
OWNERinstructions for local
inspector's use.
sure ORDIANC
instructionNTto leave
s with
OBSERVE
ALL ES.
Save OBSERVE ALL
for futureIMPORTANTKeep
IMPORTANTthe AND ORDIANCES. IMPORTA s for
these
these CODES
GOVERNING
consumer
Notereference. instruction
GOVERNING
localCODES AND ORDIANCES.
GOVERNI
NTThisNote to Installerinspector'
Be sure to leave
OBSERVE
properly
.
appliance
Note
s
Note
NG to Installer- Be sures to leave
Before grounded
these instructions
ALL
theseCODES
instructions
with theuse.
consumer.
must with the consumer. these to Installeryou
instruction
AND
be instructions
begin-Rea
OWNERKeep
these
(if
instruction
OWNER-Be
Keep these
instructions
applicable
OWNERsure ORDIANC
carefully. sfor
future reference.
d these
completel
to leave
s with
for future
reference.
ES.
).
for future Keep
IMPORTA
the
Note- This yappliance
must be
and
Note-these
This instruction
appliance
must be
consumer
Notereference.
instructionNTproperly
grounded (if applicable). properly
This properly grounded
Save
(if applicable).
.
appliance
IMPORTA s for
these
Before
you begin-Read these
s these
Before you begin-Read
Before grounded
local
GOVERNI NT- instructions
mustcompletely and
completely and
you instructions
inspector'
instruction
OBSERVE
be
begin-Rea
(if applicable
Note
NG
carefully.
s use.
carefully.
carefully. s completel
CODES
to InstallerALL
d these
these
).
Save these
AND
IMPORTA
IMPORTANTinstruction IMPORTANTy and Save these
Be sure ORDIANC
OWNERinstructions
for local inspector'sinstruction
use.
NT- instructions for local inspector's use.
to leave
s with
Save
ES.
for future Keep
IMPORTANTOBSERVE ALL
IMPORTA s for IMPORTANTthese
the
OBSERVE ALL
these
consumer
Notereference.GOVERNING
local
instruction
CODES AND ORDIANCES.
GOVERNI NTGOVERNING
This
inspector'CODES AND ORDIANCES.
OBSERVE
properly
.
applianceNote to InstallerNote
Be sure to leave
s
NG
Note to InstallerBe sure to leave
s use.
CODES
grounded
to InstallerALL
must instructions with the consumer.
these
these
instructions with the consumer.
AND
be
instruction Bethese
(if applicable
OWNEROWNER- Keep these instructions
sure ORDIANC
OWNERKeep these instructions
to
s
ES.
for
Keep
with
leave
).
for future reference.
reference.
future
the
these for future
consumer
Notereference. NoteNote- This appliance must be
instruction
This appliance must be
This
properly
.
appliance properly grounded
properly grounded (if applicable).
(if applicable).
s
grounded
must
be
(if applicable
Literature
Pack
Cover hinge with paper towel
rolls or toweling.
).
Remove Installation Instruction from
literature prepack and read them
carefully before you begin.
Be sure to place all literature, Use and
Care, Installations, etc. in a safe place
for future reference.
CAUTION: When the door is
removed and the hinge arms are at
the stop postion, DO NOT bump or
try to move the hinge arms. The
hinges could snap back causing an
injury to the hands. Cover the
hinges with toweling or empty
towel rolls while working in the
oven area.
EASY INSTALLATION OF YOUR NEW
30" WALL OVEN
Before you begin-Read these instructions completely and carefully.
IMPORTANT- Save these instructions for local inspector's use.
IMPORTANT- OBSERVE ALL GOVERNING CODES AND ORDIANCES.
Note to Installer- Be sure to leave these instructions with the consumer.
OWNER- Keep these instructions for future reference.
Note- This appliance must be properly grounded (if applicable).
FOR YOUR SAFETY
ELECTRICAL REQUIREMENTS
Before you begin-Read these
instructions completely and
carefully.
IMPORTANT- Save these
instructions for local inspector's use.
IMPORTANT- OBSERVE ALL
GOVERNING CODES AND ORDIANCES.
Note to Installer- Be sure to leave
these instructions with the consumer.
OWNER- Keep these instructions
for future reference.
Note- This appliance must be
properly grounded (if applicable).
Before you begin-Read these
instructions completely and
carefully.
IMPORTANT- Save these
instructions for local inspector's use.
IMPORTANT- OBSERVE ALL
GOVERNING CODES AND ORDIANCES.
Note to Installer- Be sure to leave
these instructions with the consumer.
OWNER- Keep these instructions
for future reference.
Note- This appliance must be
properly grounded (if applicable).
Before you begin-Read these
instructions completely and
carefully.
IMPORTANT- Save these
instructions for local inspector's use.
IMPORTANT- OBSERVE ALL
GOVERNING CODES AND ORDIANCES.
Note to Installer- Be sure to leave
these instructions with the consumer.
OWNER- Keep these instructions
for future reference.
Note- This appliance must be
properly grounded (if applicable).
Before you begin-Read these
instructions completely and
carefully.
IMPORTANT- Save these
instructions for local inspector's use.
IMPORTANT- OBSERVE ALL
GOVERNING CODES AND ORDIANCES.
Note to Installer- Be sure to leave
these instructions with the consumer.
OWNER- Keep these instructions
for future reference.
Note- This appliance must be
properly grounded (if applicable).
3
(Continued on following page)
Installation Instruction
Pre- Installation Checklist cont.
Place the Oven on a Platform
Remove the Bottom Trim
Place the oven on a table or platform
even with the cutout opening. (Platform
must support 225 lbs. )
Remove the bottom trim from the top of
the oven. It will be installed at the end of
installation. The trim is wrapped
separately and taped to the top of the unit.
Bottom Trim
Side Trim
4
Installation Instructions
A
Cutout for Built-In Oven W/Microwave
10"
CABINET
WIDTH
27"
JUNCTION BOX
LOCATION
CUTOUT
WIDTH
25" MIN.
25 1/4" MAX.
Allow 7/8"
for overlap of
oven over side
edges of cutout
2" x 4"
or
equivalent
runners
Allow a minimum of 20"
for clearance to adjacent
corners, drawers, walls, etc.
when doors are open
CUTOUT
HEIGHT
41 1/8" MIN.
41 1/4" MAX.
48"
To bottom
of junction box
Alternate
junction box
location
Cabinet Width 27”
Recommended
Cutout Location
From Floor ..... 21 5/8”
Cutout Depth . 23 1/2”
Cutout Width .. 25 ” Min.
........................ 25 1/4” Max.
Cutout Height 41 1/8” Min.
........................ 41 1/4” Max.
Overall Height 41 5/8”
Overall Width .. 26 5/8”
5"
20"
Allow 1" for
overlap of oven
top and bottom
of cutout
Recommended
cutout location
from floor
21 5/8"
If the cabinets do not have a solid bottom, then
two braces or runners must be installed to
support the weight of the oven. The runners
and braces must support 275 pounds.
NOTE: If the cabinet does not have
a front frame and the sides are
less than 3/4” thick, shim both
sides equally to establish the
cutout width.
2" x 4" or
Equivalent
Runners
NOTE: If using equivalent
runners, then the center
of the equivalent runners
should be 20 1/2”.
24"
19"
27"
5
Installation Instructions
B
Electrical Connections
B1
Turn off the circuit breaker or remove
fuses to the oven branch circuit.
B2
With the oven in front of the cabinet
opening on a table or platform,
connect the flexible conduit to the
electrical junction box as shown
below. You will need to purchase a
strain relief clamp to complete the
connection of the conduit to the
junction box.
B3
• When installing in a new construction, or
• When installing oven in a mobile home, or
• When local codes do not permit grounding
through neutral:
a. Cut the neutral
(White) lead from
the crimp. Re-strip
the neutral (white)
lead to expose the
proper length of
conductor.
20"
CONDUIT
48 1/2"
LONG
New Construction and FourConductor Branch Circuit
Connection
JUNCTION BOX
LOCATION
Ground
Wires
b.Attach the appliance
grounding lead (green or
bare copper) in accordance
Junction
with local codes. If the
Box Cover
residence grounding
conductor is aluminum, see
WARNING note on the
following page.
c. Connect the oven neutral (white) lead to
the branch circuit neutral (white or gray) in
accordance with local codes.
BARE GROUND
RED
WHITE
BLACK
STRAIN RELIEF CLAMP
( NOT INCLUDED )
MUST BE USED
AT JUNCTION BOX
d.Connect the oven red lead to the branch
circuit red lead and the oven black lead to
the branch circuit black lead in accordance
with local codes. If the residence red,
black or white leads are aluminum
conductors, see “ WARNING” note on the
following page.
e. Install the Junction Box Cover.
PLACE OVEN ON
A SUPPORT
TO ASSIST IN
CONNECTING
CONDUIT
OR
6
(Continued on following page)
Installation Instructions
B
Electrical Connections cont.
B4
Three-Conductor Branch Circuit Connection
When connecting to a 3-conductor branch
circuit, if local codes permit:
a. Connect the bare oven ground conductor
with the crimped neutral (white) lead to the
branch circuit neutral (white or gray in
color).
b. The oven red lead to the branch circuit red
lead.
c. The oven black lead to the branch circuit
black lead in accordance with local codes.
d. Install Junction Box Cover.
NOTE TO ELECTRICIAN: The 3 power leads
supplied with this appliance are UL recognized
for connection to larger gauge household wiring.
The insulation of these 3 leads is rated at
temperatures much higher than the temperature
rating of household wiring. The current carrying
capacity of the conductor is governed by the
temperature rating of the insulation around the
wire, rather than the wire gauge alone.
WARNING: Improper connection of
aluminum house wiring to copper leads
can result in an electrical hazard or fire.
Use only connectors designed for joining
copper to aluminum and follow the
manufacturer’s recommended procedure
closely.
Ground
& Neutral
Wires
Junction Box
Cover
Do not shorten this flexible conduit. The
conduit strain relief clamp must be
securely attached to the junction box and
the flexible conduit must be securely
attached to the clamp. If the flexible
conduit will not fit within the clamp, do
not install the oven until a clamp of the
proper size is obtained.
7
Installation Instructions
C
Placing the Oven In the Opening
C1 Sliding the Oven Into the
C3 Drilling the Pilot Holes
Opening.
a. Loop a 36” string around the conduit before
the oven is slid into place. This will keep the
conduit from falling behind the oven.
NOTE: Before drilling the pilot holes,
make sure the oven is pushed as far
back into the opening as it will go,
and that it is centered.
Pull out on the
string while pushing
the oven into the
cabinet.
PULL OUT ON
STRING LOOP
WHILE PUSHING
THE OVEN
INTO THE CABINET
a. Drill four-1/8” pilot holes through the
mounting holes (top and bottom) of the
side trim, for the four #8 screws provided.
The screws must
be a minimum of
1/4” from the front
edge of the
cutout.
b. Lift oven into cabinet cutout using the oven
opening as an grip. Carefully push against
oven front frame. Do not push against outside edges.
c. As the oven is slid back, pull the string so
that the conduit will lie behind the oven in a
natural loop.
d. When you are sure the conduit is out of the
way, slide the oven 3/4 the way back into the
opening. Remove the string.
C2
MOUNTING HOLE LOCATIONS
Installing the Bottom Trim
a. Slide the oven 3/4 way
into the cabinet cutout.
b. Attach the bottom trim to
the front frame with the 3
screws provided.
c. Slide the oven all the way
into the cabinet cutout.
Side
Trim
Lower
Trim
NOTE: Mounting screws must be
used. Failure to do so could result in
the oven falling out of the cabinet
causing serious injury.
Trim
Screw
b. Secure the Oven to Cabinet with screws
provided.
Caution: Be sure you do not tip the oven
foward during installation or you may bend
the bottom trim. The bottom trim provides
an opening for cooling air to enter the
cabinet. This opening should never be
blocked.
NOTE: If the cabinet is particle board, you
must use 4 #8 x 3/4” particle board screws.
These may be purchased at any hardware
store.
8
Installation Instructions
D
Replacing the Oven Door
D1
Make sure the hinge is in the door stop
position.
D2
Remove the toweling or paper towel
holder from the hinge.
D3
Grasp the door on both sides.
D4
Hold the door over the hinges aligning
the hinges with the hinge slots on the
bottom of the door.
D5
Slide the door down onto the hinges as
far as it will go.
D6
Close the door.
The oven door is heavy. You may need
help lifting the door high enough to
slide it down onto the hinges. Do not
lift the door by the handle.
9
Installation Instruction
E PRE-TEST CHECK LIST
Remove all protective film if present,
and any stickers.
Check that the bottom trim is installed
properly (see page 7).
Check to be sure that all wiring is
secure and not pinched or in contact
with moving parts.
Check to be sure the mounting screws
are installed and flush with the side
trim, (see page 7).
Operation Checklist
NOTE TO ELECTRICIAN:
The power leads supplied with this
appliance are UL recognized for
connections to larger gauge
household wiring. The insulation of
these leads is rated at temperatures
much higher than the temperature
rating of household wiring. The
current carrying capacity of a
conductor is governed by the wire
gauge and also the temperature rating
of the insulation around the wire.
Remove all items from the inside
of the oven.
Turn on the power to the oven.
(Refer to your Use and Care
Manual.) Verify that the bake and
broil units, and all cooking
functionsoperate properly.
Check that the circuit breaker is
not tripped or the house fuse is
blown.
NOTE: ALUMINUM WIRING
A. WARNING:
IMPROPER CONNECTION OF
ALUMINUM HOUSE WIRING TO
THE COPPER LEADS CAN
RESULT IN A SERIOUS PROBLEM.
B. Splice copper wires to aluminum
wiring using special connectors
designed and UL approved for
joining copper to aluminum and
follow the manufacturer’s
recommended connector
procedure closely.
NOTE:Wire used, location and
enclosure of splices, etc., must
conform to good wiring practice and
local codes.
Check that conduit is securely
connected to the junction box.
See Use & Care manual for
troubleshooting list.
10
NOTES
11
NOTES
12
Pub. No. 31-462
229C4053P430
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising