GE | RAK3203 | Installation instructions | GE RAK3303 Installation Instructions

GE RAK3303 Installation Instructions
Installation instructions
for your new
RAK3153A, RAK3203A,
RAK3303A
Power Supply Kit for Cord
Connection with Current
Interruption Device
Before you begin – Read these instructions completely and carefully.
IMPORTANT – OBSERVE ALL GOVERNING CODES AND ORDINANCES.
Note to Installer – Be sure to leave these instructions with the Consumer.
Note to Consumer – Keep these instructions with your Owner’s Manual for future reference.
TOOLS NEEDED
• 1/4″ Nut driver
• Phillips screwdriver
• This kit is for use with 230/208 volt 2800, 2900,
3800, 3900, 4100, 5200, 5500, 5800 and 6100
Series GE Zoneline units only.
230/208 VOLT ELECTRICAL SUPPLY
A power supply kit must be used to supply power to the
Zoneline unit. The appropriate kit is determined by the
voltage, the means of electrical connection, and the
amperage of the branch circuit. See the POWER
CONNECTION CHART to confirm the appropriate kit.
WARNING: Disconnect the electrical power
supply before wiring connections.
IMPORTANT NOTES
• This unit must be properly grounded.
• The electrical rating marked on the previously installed
Zoneline and power supply kit must be the same as
the supply branch circuit.
• Aluminum building wiring may present special
problems—consult a qualified electrician.
• All wiring, including installation of the receptacle,
must be in accordance with the NEC and local codes,
ordinances, and regulations.
• Use ONLY the wiring size recommended for single
outlet branch circuit.
• Proper current protection is the responsibility of
the owner.
Recommended branch circuit wire sizes*
Appearance may vary.
Power supply kit
All wiring, including installation of the receptacle,
must be in accordance with the NEC and local codes,
ordinances, and regulations.
Tandem
15 Amp
Perpendicular
20 Amp
Large Tandem
30 Amp
Nameplate
maximum circuit
breaker size
AWG wire
size**
15A
20A
30A
14
12
10
AWG – American Wire Gauge
* Single circuit breaker from main box
** Based on copper wire, single-insulated conductor at 60°C
NOTE: Use copper conductors only.
230/208 volt receptacle configuration
POWER CONNECTION CHART
GE 230/208 Volt
Power Supply Kit
RAK3153A
RAK3203A
RAK3303A
Printed in the United States
Wall Plug
Configuration
Circuit Protective Device
Heater Wattage
@ 230/208 Volts
Tandem
Perpendicular
Large Tandem
15-Amp Time-Delay Fuse or Breaker
20-Amp Time-Delay Fuse or Breaker
30-Amp Time-Delay Fuse or Breaker
2.55/2.09 KW
3.45/2.82 KW
5.00/4.09 KW
Pub No. 31-61544
08-09 JR
FOR 230/208 VOLT POWER CORD CONNECTIONS ONLY
1. Remove the room cabinet by pulling it out at the bottom
to release it (1); then lift it up to clear the rail along the
unit top (2).
Test the Current Interrupter
These kits include a Leakage Current Detection
Interrupter (LCDI) device. These Current Interruption (CI)
devices comply with Underwriters Laboratories (UL)
1699 and National Electrical Code (NEC), section 440.65
and are not required to function as Ground Fault Circuit
Interrupters (GFCI).
1. Set the Zoneline unit to operate in Low Fan mode and
verify operation.
2. Press the Test button. Reset button should pop out with
a click. Unit should shut down with no power.
3. If Test button does not trip and remove power from unit
when depressed, contact a qualified service technician.
2. Insert the plug into the socket located in the wiring
compartment, making sure the plug is firmly seated
and the latches secure the connector assembly.
4. Press the Reset button. Test button should pop out
with a click and unit should resume operation.
Due to the Random Restart feature, there is a
planned 2 to 25 second delay in the restart of
the Zoneline.
5. If unit does not operate, repeat steps 2 through 4.
6. If unit still does not operate, contact a qualified service
technician.
7. Test the current interrupter device on a periodic basis.
Yellow plug
to chassis
connector
Screw
Strain
relief
Plug into
building
receptacle
Cord
3. Position the cord and install the strain relief and screw
as shown.
4. Reinstall the room cabinet front by positioning on the
top brackets and securing the sides to the unit.
5. Install the attachment plug cap into the wall
receptacle and check the Zoneline operation.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising