GE | ZDBC240NBS | Use and Care Manual | GE ZDBC240NBS Use and Care Manual

GE ZDBC240NBS Use and Care Manual
Owner’s
Manual
Beverage Center
ZDBC240
monogram.com
Consumer Information
Beverage Center
Introduction
Your new Monogram beverage center makes an eloquent statement of style,
convenience and kitchen planning flexibility. Whether you chose it for its purity of design
or the assiduous attention to detail, you will find that your Monogram beverage center’s
superior blend of form and function will delight you for years to come.
The information on the following pages will help you operate and maintain your beverage
center properly.
If you have any other questions, visit our Website at: monogram.com
Contents
Care and Cleaning . . . . . . . . . . . . . . . . . .10, 11
Consumer Services . . . . . . . . . . . . . . . . . . . .19
Controls and Features . . . . . . . . . . . . . . . . .8, 9
Model and Serial Numbers . . . . . . . . . . . . . . .2
Problem Solver . . . . . . . . . . . . . . . . . . . . .13–15
Product Registration . . . . . . . . . . . . . . . . . . . .2
Repair Service . . . . . . . . . . . . . . . . . . . . . . .3, 19
Reversing the Door Swing . . . . . . . . . . . . . .12
Safety Instructions . . . . . . . . . . . . . . . . . . . .4–7
Warranty . . . . . . . . . . . . . . . . . . . . .Back Cover
Before
using your
beverage
center
Read this manual carefully. It is intended to
help you operate and maintain your new
beverage center properly.
If you don’t understand something or
need more help, there is a list of toll-free
consumer service numbers included in
the back section of this manual.
Keep it handy for answers to your
questions.
OR
Visit our Website at: monogram.com
Write
down the
model &
serial
numbers
You will find them on a label on the ceiling
inside the beverage center.
Please write these numbers here:
Model Number
Serial Number
Use these numbers in any correspondence
or service calls concerning your beverage
center.
ATTENTION CONSUMER!
This unit is designed for storing and cooling beverages.
Do not store perishable foods in this unit.
ATTENTION CONSOMMATEUR !
2
Cet appareil ménager est conçu pour conserver et rafraîchir des boissons.
Ne mettez pas de biens perissables dans cet appareil ménager.
Consumer Information
Beverage Center
If you
received a
damaged
appliance
The warranty does not cover damage
caused after delivery.
Immediately contact the dealer (or builder)
that sold you the beverage center.
Remove
packaging
Before using, be sure all packing materials
and tape have been removed.
new appliances is an application of
household liquid detergent. Apply with
a soft cloth and allow to soak. Wipe dry
and then apply an appliance polish to
thoroughly clean and protect the surface.
To assure no damage is done to the finish
of the product, the safest way to remove
the adhesive left from packaging tape on
If you
need
service
To obtain service, see the Consumer
Services page in the back of this manual.
We are proud of our service and want you
to be pleased. If for some reason you are
not happy with the service you receive,
here are steps to follow for further help.
For customers in the USA:
FIRST, contact the people who serviced your
appliance. Explain why you are not pleased.
In most cases, this will solve the problem.
NEXT, if you are still not pleased, write
all the details—including your phone
number—to:
For customers in Canada:
FIRST, contact the people who serviced your
appliance. Explain why you are not pleased.
In most cases, this will solve the problem.
NEXT, if you are still not pleased, write
all the details—including your phone
number to:
Manager, Consumer Relations
Mabe Canada Inc.
1 Factory Lane, Suite 310
Moncton, N.B. E1C 9M3
Manager, Customer Relations
GE Appliances
Appliance Park
Louisville, KY 40225
After
installation
is completed
• Promptly inspect your new Monogram
Beverage Center. If it has been damaged,
contact the Installer or Dealer
immediately.
• This Beverage Center must be properly
leveled to ensure correct door alignment
and door closure. Contact the Installer if
the unit is not level.
• The unit should be centered in the
opening. The front face of the door
should be 1″ forward of adjacent
cabinetry. Contact the installer if
clearance is not correct.
• Test the door swing. Carefully open and
close the door. The door should not rub
or catch on adjacent cabinetry. Notify
the installer if the door makes contact
with cabinetry.
Please Contact the Installer or Dealer if
you experience any of these problems.
Your Beverage Center is shipped with a
black toekick on the front of the unit. For
shipping purposes, an optional stainless
steel toekick is secured to the back of
the unit. That toekick should have been
removed and installed, or given to you.
Keep the unused toekick and other unused
or removed parts for possible future use.
3
IMPORTANT SAFETY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
BEFORE IT IS USED, THE APPLIANCE MUST BE PROPERLY INSTALLED AND
LOCATED AS DESCRIBED IN THIS MANUAL.
wDANGER: RISK OF CHILD ENTRAPMENT
Child entrapment and suffocation
are not problems of the past. Junked or
abandoned refrigeration products are
still dangerous…even if they will sit for
“just a few days.” If you are getting rid
of your old appliance, please follow these
instructions to help prevent accidents.
Before You Throw Away Your Old
Refrigeration Product:
• Take off the doors.
• Leave the shelves in place so that children
may not easily climb inside.
REFRIGERANTS
All refrigeration products contain
refrigerants, which under federal law must
be removed prior to product disposal.
If you are getting rid of an old refrigeration
product, check with the company handling
the disposal about what to do.
USE OF EXTENSION CORDS
Because of potential safety hazards
under certain conditions, we strongly
recommend against the use of an
extension cord.
4
However, if you must use an extension
cord, it is absolutely necessary that it be a
UL-listed, 3-wire grounding type appliance
extension cord having a grounding type
plug and outlet and that the electrical rating
of the cord be 15 amperes (minimum) and
120 volts.
IMPORTANTES INSTRUCTIONS DE SÉCURITÉ
LIRE ET CONSERVER CES INSTRUCTIONS
AVANT D’ÊTRE UTILISÉ, L’APPAREIL MÉNAGER DOIT ÊTRE BIEN INSTALLÉ ET SE
TROUVER À L’ENDROIT DÉCRIT DANS CETTE MANUEL.
wDANGER! RISQUES POUR LES ENFANTS
Les enfants pris au piège ou morts
d’asphyxie sont toujours d’actualité.
Les appareils de réfrigération abandonés
sont toujours aussi dangereux, même
si on n’attend que “quelque jours” pour
s’en débarasser. Si vous ne gardez pas
votre ancien appareil, veuillez suivre
les directives ci-dessous afin de prévenir
les accidents.
Avant de vous débarasser de votre vieux
appareil de réfrigération :
• Démontez les portes.
• Laissez les clayettes en place afin
d’empêcher les enfants de grimper à
l’intérieur.
RÉFRIGÉRANTS
Tous les appareils de réfrigération
contiennent des refrigerants qui,
conformément aux lois fédérales, doivent
être enlevés avant toute élimination de
l’appareil.
Si vous vous débarrassez de vieux
appareils de réfrigération, vérifiez,
auprès de la société qui s’occupe de
leur élimination, ce que vous devez faire.
CORDONS PROLONGATEURS
Nous vous recommandons fortement de
ne pas utíliser de cordons prolongateurs
à cause des risques potentiels qu’ils
présentent dans certaines conditions.
Toutefois si vous décidez d’utiliser tout
de même un cordon prolongateur, il est
absolument nécessaire qu’il s’agisse d’un
cordon à 3 fils avec mise à la terre pour
appareils électroménagers homologué
UL (aux États-Unis) ou homologué CSA
(au Canada), pourvu d’une fiche et d’une
prise mises à la terre de 15 ampères
(minimum) et de 120 volts.
5
IMPORTANT SAFETY INSTRUCTIONS
HOW TO CONNECT ELECTRICITY
Do not, under any circumstances, cut
or remove the third (ground) prong from
the power cord. For personal safety, this
appliance must be properly grounded.
The power cord of this appliance is
equipped with a 3-prong (grounding)
plug which mates with a standard 3-prong
(grounding) wall outlet to minimize the
possibility of electric shock hazard from
this appliance.
Have the wall outlet and circuit checked
by a qualified electrician to make sure
the outlet is properly grounded.
Where a standard 2-prong wall outlet
is encountered, it is your personal
responsibility and obligation to have
it replaced with a properly grounded
3-prong wall outlet.
The appliance should always be plugged
into its own individual electrical outlet which
has a voltage rating that matches the rating
plate. This provides the best performance
and also prevents overloading house wiring
circuits which could cause a fire hazard
from overheated wires.
Never unplug an appliance by pulling on
the power cord. Always grip the plug firmly
and pull straight out from the outlet.
Repair or replace immediately all
power cords that have become frayed
or otherwise damaged. Do not use a cord
that shows cracks or abrasion damage
along its length or at either end.
When moving the appliance, be careful not
to roll over or damage the power cord.
SAVE THESE INSTRUCTIONS
6
IMPORTANTES INSTRUCTIONS DE SÉCURITÉ
RACCORDEMENT ÉLECTRIQUE
Ne coupez ni retirez en aucun cas
la troisième broche (mise à la terre)
de la fiche du cordon d’alimentation.
Pour votre sécurité, cet appareil doit
être correctement mis à la terre.
Le appareil doit toujours être branché dans
sa propre prise de courant, dont la tension
nominale est identique à celle indiquée sur
la plaque signalétique.
Le cordon d’alimentation de cet appareil
est muni d’une fiche à 3 broches (mise
à la terre) qui se branche dans une prise
mural ordinaire à 3 alvéoles (mise à la terre)
pour réduire au minimum les risques du
chocs électriques.
Faites examiner la prise de courant et
le circuit par un électricien qualifié pour
vous assurer que la prise est correctement
mise à la terre.
Si la prise murale est du type standard
à 2 alvéoles, il vous incombe de la faire
remplacer par une prise à 3 alvéoles
correctement mise à la terre.
Cette précaution est recommandée pour
garantir un rendement optimum et éviter
une surcharge des circuits électriques de
la résidence, ce qui pourrait créer un risque
d’incendie par surschauffe des fils.
Ne débranchez jamais l’appareil en
tirant le cordon d’alimentation. Saisissez
fermement la fiche du cordon et tirez droit
pour la retirer de la prise.
Réparez ou remplacez immédiatement tout
cordon effiloché ou endommagé. N’utilisez
pas un cordon fendillé ou présentant des
signes d’usure.
Lorsque vous déplacez l’appareil du mur,
faites attention de ne pas la faire rouler
sur le cordon d’alimentation afin de ne pas
l’endommager.
CONSERVEZ CES DIRECTIVES
7
Controls and Features
Beverage Center
Temperature
control
The operating temperatures of the
beverage center range from the low forties
to the mid fifties.
This appliance is not a refrigerator and
does not maintain temperatures like a
refrigerator (below 40°F).
To set the control, turn it to the midpoint
setting (approximately 45ºF). Once the
beverage center is loaded, allow at least
24 hours before making any adjustments
to the initial setting.
Do not install the beverage center where
the temperature will go below 55°F (13°C)
or above 90°F (32°C).
As with any refrigeration-type product,
there is a slight temperature variance at
different locations within the cabinet.
The coolest area will be in the lower part
of the cabinet.
The cooler area will be in the middle section.
The upper part of the cabinet is the
warmest section.
When the temperature is adjusted, allow
24 hours for the unit to stabilize.
NOTES:
•This unit is designed for storing and
cooling beverages. It is not intended for
the storage of perishable foods.
•The lowest temperatures are found on the
lower shelves/racks and toward the rear of
the shelves/racks.
Interior light
and switch
The interior light makes it easy to view your
beverage labels and enhances the display
of your collection.
When the switch is in the OFF position,
the light comes on only when the door
is opened. When the switch is in the ON
position, the light remains on continuously
for your maximum viewing pleasure. For
best viewing, do not store a bottle on the
top shelf directly under the light. Remember
to turn off the light when it is no longer
needed.
Glass
shelves
Tempered glass shelves in the beverage
center unit are removable for easy cleaning
or for storing larger items.
To replace a shelf, open the door
completely to avoid potential damage
to the gasket. Tilt the shelf to one side
at an angle and slide toward the back wall,
placing one side onto the shelf support.
Place the other side onto the opposite
shelf support. Ensure rear locking tabs are
engaged. When installed properly, the shelf
will not slide forward when gently pulled.
To remove a shelf, open the door
completely to avoid potential damage to
the gasket. Lift up on the back of the shelf
slightly. Tilt the shelf to one side at an angle
while pulling forward.
To remove, lift up on the back of the shelf
8
Tilt the shelf at an angle while removing
or replacing
Place in slots when replacing the shelf
Controls and Features
Beverage Center
Loading
tips and
suggestions
The bottom two full extension drawers hold
six bottles each and are loaded with necks
facing the rear. Tall bottles should not be
loaded on the bottom drawer because
they may prevent the door from closing.
Do not allow children to climb, stand
or hang on the beverage center shelves
or full extension drawers. They could
seriously injure themselves and possibly
cause damage to the beverage center.
NOTE: This unit is for storing beverages only
and not intended for the storage of
perishable foods.
Removing
full
extension
drawers
Bottom drawer arrangement
The bottom full extension drawers pull
out so bottles can conveniently be added
or removed.
The upper full extension slide can be
removed for magnums or larger bottles.
To remove:
Tab (push tab down on right
drawer guide, pull tab up on
left drawer guide)
1. Pull the full extension drawer out to the
STOP position.
2. Push the tab on right drawer guide down
while pulling the tab on left guide up, and
pull the drawer out.
To replace:
1. Push the drawer slide arm back into
the unit.
2. Pull the small slide sub-assembly
completely forward.
3. Insert the sides of the drawer back
into the guides.
4. Push until the tabs lock into place.
Wood
drawer
fronts
The full extension drawer fronts on the
beverage center are unfinished cherry
wood. During use, oil from hands may
accumulate and stain the wood.
•The drawer fronts may be stained and
sealed to match adjacent cabinetry. The
tinted glass will make the stained wood
appear darker. A true color match can be
seen only when the door is opened.
Sub-assembly
To replace, push drawer slide
arm back into unit
Sub-assembly
Pull small slide sub-assembly
completely forward
NOTE: Make sure the tabs on the full
extension drawer guides are fully engaged
before loading any bottles. Pull the drawers
out all the way to the STOP position and
push back in several times to make sure
locking tabs are properly engaged.
•Apply the stain and sealer according to
the manufacturer’s instructions. To avoid
unpleasant odor, keep the door open to
ventilate and allow the stain/sealer to dry
completely before using the product.
NOTE: Natural wood may vary slightly in
grain and color.
9
Care and Cleaning
Beverage Center
Unplug the beverage center before cleaning.
Cabinet
The exterior surfaces can be washed with
mild soap and water. Rinse thoroughly with
clear water. Never use abrasive scouring
powders.
Glass door
Use a glass cleaner or mild soap and water
and a soft cloth to clean the glass door.
Do not use any abrasive powders.
Door gasket
The vinyl gasket may be cleaned with mild
soap and water, a baking soda solution or
a mild scouring powder. Rinse well.
After cleaning the door gasket, apply a thin
layer of paraffin wax or petroleum jelly to
the door gasket at the hinge side. This helps
keep the gasket from sticking and bending
out of shape.
Light bulb
replacement
Unplug the beverage center before
replacing the light bulb.
To remove the light shield, push in the tab
on the left side of the shield and lower it.
Replace with a 15 watt appliance bulb.
In the event
of a power
failure
If the power fails, open the door as
infrequently as possible to maintain
the temperature.
Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.
10
Care and Cleaning
Beverage Center
Unplug the beverage center before cleaning.
Cleaning the
inside
Drain hole
Turn the beverage center unit OFF or
unplug the unit before cleaning. Use a
slightly damp cloth or sponge when cleaning
around switches, lights or controls.
Other parts of the beverage center unit—
including the door gaskets, full extension
drawers and glass shelves—can be cleaned
the same way.
Use warm water and baking soda solution—
about a tablespoon (15 ml) of baking soda
to a quart (1 liter) of water. This both cleans
and neutralizes odors. Thoroughly rinse and
wipe dry.
Avoid cleaning cold glass shelves with hot
water because the extreme temperature
difference may cause them to break. Handle
glass shelves carefully. Rough handling of
tempered glass can cause it to shatter.
Periodically check the drain hole and
channel for any debris. If the drain is blocked,
condensation will not drain properly.
Drain hole
To check and clean the drain hole, remove
the bottom two glass shelves. Sweep a damp
cloth along the channel in the back of the
beverage center. Use a finger to sweep
away any debris from the drain hole.
11
Reversing the Door Swing
Beverage Center
To reverse
the door
Parts included:
1. Top left case hinge
2. Bottom left case hinge
3. Left and right side decorative hinge
cover
4. Decorative hinge screw hole cover
5. Torx® driver bit
Tools required:
1. Phillips screwdriver
2. Electric drill
Install
3 Hinge
Screws
Remove
Top Hinge
Hinge
Pin and
Bracket
Door Stop
and Cam Riser
To remove the door:
1. Flatten the shipping carton to use as
a pad.
2. Remove the 2 screws and the toekick.
Set aside the screws and toekick for final
installation.
3. Use the supplied Torx® bit and electric
drill to remove the 3 screws holding the
top case hinge. Lift off the hinge. (Screws
will be used to install the new hinge.)
4. Lift the door off the bottom case hinge.
5. Remove the bottom case hinge pin
and bracket.
Rotate the door:
The handle will be on the right side of the
door; hinges will be installed on the left side
of the case.
1. Remove the door stop and cam riser
on the original bottom right side of
the door.
2. Remove the fill plug on the top right side
of the door.
3. Turn the door over and reinstall the
fill plug on the new left side.
Remove
Hinge
To reinstall the door:
1. Install the original door stop and cam
riser onto the bottom left side of the
door.
2. Install the new supplied bottom case
hinge pin and bracket onto bottom left
side.
3. Place the door onto the bottom case
hinge.
4. Install the supplied left-hand top case
hinge with the 3 original screws.
5. Select the hinge cover marked with
an “L”.
6. Peel backing off the tape inside
the decorative hinge cover.
7. Press and snap
the hinge cover
Install Covers
into place.
8. Snap the screw
hole cover into
place on the
opposite side.
Important: Check to be sure screws are
tight and that the door is straight and does
not sag. The door should swing freely.
Note: See Installation Instructions to apply
hinge cover and screw hole cover.
Position nameplate:
Apply the Monogram nameplate on the
door using the template included in the
installation instructions.
12
The Problem Solver
Beverage Center
Normal
operating
sounds
Newer appliances sound different from older appliances. Modern appliances have more
features and use newer technology.
Do you hear what I hear? These sounds are normal.
HUMMM...
WHOOSH...
• The new high efficiency compressor
may run faster and longer than your
old appliance and you may hear a highpitched hum or pulsating sound while
it is operating.
• Sometimes the appliance runs for an
extended period, especially when the
doors are opened frequently.
• You may hear the fans spinning at high
speeds. This happens when the appliance
is first plugged in, when the door is
opened frequently or when large amounts
of beverages are added to the appliance.
The fans help maintain desired
temperatures.
• You may hear a whooshing sound when
the doors close. This is due to pressure
equalizing within the appliance.
• If the door is open for over 3 minutes, you
may hear a fan come on in order to cool
the appliance.
• The fans change speeds in order to provide
optimal cooling and energy savings.
CLICKS, POPS,
CRACKS and CHIRPS
WATER SOUNDS
• You may hear cracking or popping sounds
when the appliance is first plugged in.
This happens as the appliance cools to
the correct temperature.
• The flow of refrigerant through the
appliance cooling coils may make a
gurgling noise like boiling water.
• Expansion and contraction of cooling coils
during and after defrost can cause a
cracking or popping sound.
• A water dripping noise may occur as
water from the evaporator flows into the
drain pan.
• Closing the drawer may cause a gurgling
sound due to pressure equalization.
13
The Problem Solver
Beverage Center
Questions?
Use this
problem
solver!
PROBLEM
POSSIBLE CAUSE
APPLIANCE
DOES NOT OPERATE
• Appliance may be in defrost cycle when motor does not operate for
about 30 minutes.
• If interior light is not on, appliance may not be plugged in at
wall outlet. Push the plug completely into the wall outlet.
• The fuse is blown/circuit breaker is tripped. Replace fuse or reset
the breaker.
VIBRATION OR
RATTLING (Slight
vibration is normal.)
• Adjust the leveling legs as shown in the Installation Instructions.
MOTOR OPERATES
FOR LONG PERIODS
OR CYCLES ON AND
OFF FREQUENTLY
• Normal when appliance is first plugged in. Wait 24 hours for the
appliance to completely cool down.
• Often occurs when large amounts of beverages are placed in appliance.
This is normal.
• Door left open or package holding door open.
• Hot weather or frequent door openings. This is normal.
• Temperature control set at the coldest setting.
See Temperature Control. Allow 24 hours for temperature to change.
COMPARTMENT
TOO WARM
• Temperature control not set cold enough.
See Temperature Control. Allow 24 hours for temperature to change.
• Warm weather or frequent door openings.
• Door left open for long time.
• Package may be holding door open.
APPLIANCE
HAS ODOR
• Interior needs cleaning. See Care and Cleaning.
DOOR NOT
CLOSING
PROPERLY
• Door gasket is sticking or folding over. Apply petroleum jelly
or paraffin wax to the face of the gasket.
MOISTURE FORMS
ON OUTSIDE OF
APPLIANCE
• Not unusual during periods of high humidity. If bothersome,
wipe surface dry; otherwise, moisture will evaporate in time.
FROST OR MOISTURE
COLLECTS INSIDE
• Keep open box of baking soda in appliance; replace every 3 months.
• The door is hitting an internal component inside the appliance.
Adjust interior components to prevent interference.
• Door left open or package holding door open.
• Too frequent or too long door openings.
• In humid weather, air carries moisture into appliance when door
is opened. Unit will dissipate moisture in time. If bothersome,
wipe surface dry.
• Temperature control set at coldest setting.
INTERIOR LIGHT
DOES NOT WORK
14
• No power at outlet.
• Light bulb needs replacing. See Care and Cleaning.
The Problem Solver
Beverage Center
Questions?
Use this
problem
solver!
PROBLEM
POSSIBLE CAUSE
HOT AIR FROM
BOTTOM OF
APPLIANCE
• Normal air flow cooling motor. In the refrigeration process, it is
normal that heat be expelled in the area under the appliance.
Some floor coverings are sensitive and will discolor at these safe
and normal temperatures.
APPLIANCE
NEVER SHUTS OFF
BUT TEMPERATURES
ARE OK
• Adaptive defrost keeps compressor running during door openings.
This is normal. The appliance will cycle off after the door remains
closed for two hours.
• Normal operation in extreme temperatures.
15
Wine or Beverage Storage and Handling Notes
Beverage Center
16
Wine or Beverage Storage and Handling Notes
Beverage Center
17
Appliance Notes
Beverage Center
18
Consumer Services
Beverage Center
With the purchase of your new Monogram appliance, receive the
assurance that if you ever need information or assistance from
GE, we will be there. All you have to do is call—toll-free!
GE Answer
Center®
In the USA:
800.626.2000
Whatever your question about any Monogram major appliance, GE Answer Center®
information service is available to help. Your call—and your question—will be answered
promptly and courteously. And you can call any time. GE Answer Center® service is open
24 hours a day, Monday through Saturday.
OR
Visit our Website at: monogram.com
In Canada, call 1.800.561.3344.
In-Home
Repair
Service
In the USA:
800.444.1845
In Canada:
1.800.561.3344
For
Customers
With Special
Needs…
A GE consumer service professional will provide expert repair service, scheduled at a time that’s
convenient for you. Many GE Consumer Service company-operated locations offer you service
today or tomorrow, or at your convenience (7:00 a.m. to 10:00 p.m. weekdays, 8:00 a.m. to 6:00 p.m.
Saturday and Sunday). Our factory-trained technicians know your appliance inside and out—so most
repairs can be handled in just one visit. In Canada: Monday to Friday, 7:00 a.m. to 8:00 p.m. and
Saturday, 8:00 a.m. to 5:00 p.m. EDST.
GE offers Braille controls for a variety of GE appliances, and a brochure to
assist in planning a barrier-free kitchen for persons with limited mobility.
Consumers with impaired hearing or speech who have access to a TDD or
a conventional teletypewriter may call 800.TDD.GEAC (800.833.4322)
to request information or service.
In the USA:
800.626.2000
Service
Contracts
You can have the secure feeling that GE Consumer Service will still be there after your warranty
expires. Purchase a GE contract while your warranty is still in effect and you’ll receive a substantial
discount. With a multiple-year contract, you are assured of future service at today’s prices.
In the USA:
800.626.2224
In Canada:
1.800.561.3344
Parts and
Accessories
Individuals qualified to service their own appliances can have parts or accessories sent directly
to their home. The GE parts system provides access to over 47,000 parts…and all GE Genuine Renewal
Parts are fully warranted. VISA, MasterCard and Discover cards are accepted.
In the USA:
800.626.2002
In Canada:
1.800.561.3344
User maintenance instructions contained in this manual cover procedures intended to be
performed by any user. Other servicing generally should be referred to qualified service
personnel. Caution must be exercised, since improper servicing may cause unsafe operation.
19
Consumer Services
Beverage Center
YOUR MONOGRAM BEVERAGE CENTER WARRANTY
Staple sales slip or cancelled check here. Proof of original
purchase date is needed to obtain service under warranty.
WHAT IS
COVERED
From the Date
of the Original
Purchase
LIMITED ONE-YEAR WARRANTY
WHAT IS NOT
COVERED
• Service trips to your home to teach you how
to use the product.
• Replacement of house fuses or resetting of circuit
breakers.
• Damage to the product caused by accident, fire,
floods or acts of God.
• Failure of the product if it is used for other than
its intended purpose or used commercially.
• Damage caused after delivery.
For one year from date of original purchase, we will provide, free of charge, parts and service labor in your home
to repair or replace any part of the unit that fails because of a manufacturing defect.
LIMITED FIVE-YEAR WARRANTY
For five years from date of original purchase, we will provide, free of charge, parts and service labor
in your home to repair or replace any part of the sealed refrigerating system (the compressor, condenser,
evaporator and all connecting tubing) that fails because of a manufacturing defect.
This warranty is extended to the original purchaser and any succeeding owner for products purchased for
ordinary home use in the 48 mainland states, Hawaii, Washington, D.C. or Canada. If the product is located
in an area where service by a GE Authorized Servicer is not available, you may be responsible for a trip charge
or you may be required to bring the product to an Authorized GE Service location for service. In Alaska the
warranty is the same except that it is LIMITED because you must pay to ship the product to the service shop
or for the service technician’s travel costs to your home.
All warranty service will be provided by our Factory Service Centers or by our authorized Customer Care®
servicers during normal working hours.
Should your appliance need service, during warranty period or beyond, in the USA call 800.444.1845. In
Canada: 800.561.3344. Please have your serial number and model number available when calling for service.
• Improper installation, delivery or maintenance.
If you have an installation problem, contact
your dealer or installer. You are responsible for
providing adequate electrical, plumbing and
other connecting facilities.
• Replacement of the light bulbs, if included.
• Loss of food due to spoilage (in the USA only).
• Incidental or consequential damage caused
by possible defects with this appliance.
• Product not accessible to provide required
service.
EXCLUSION OF IMPLIED WARRANTIES—Your sole and exclusive remedy is product repair as provided in
this Limited Warranty. Any implied warranties, including the implied warranties of merchantability or
fitness for a particular purpose, are limited to one year or the shortest period allowed by law.
Some states/provinces do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may
also have other rights which vary from state to state/province to province. To know what your legal rights are
in your state/province, consult your local or state/provincial consumer affairs office or your state’s Attorney
General.
Warrantor in USA: General Electric Company,
Louisville, KY 40225
Warrantor in Canada: Mabe Canada Inc.,
Burlington, Ontario
197D4614P006
49-60430-2
08-07 JR
Printed in Slovenia
GE Consumer & Industrial
Appliances
General Electric Company
Louisville, KY 40225
ge.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising