Garmin | SRX400, Fusion, Marine Stereo, Retail | Installation instructions | Garmin SRX400, Fusion, Marine Stereo, OEM Installation Instructions

Garmin SRX400, Fusion, Marine Stereo, OEM Installation Instructions
®
Apollo™ SRX400 Installation
Instructions
Important Safety Information
WARNING
See the Important Safety and Product Information guide in the
product box for product warnings and other important
information.
CAUTION
Always wear safety goggles, ear protection, and a dust mask
when drilling, cutting, or sanding.
NOTICE
When drilling or cutting, always check what is on the opposite
side of the surface.
Getting the Owner's Manual
You can get the latest owner's manual and translations of
manuals from the web.
1 Go to www.fusionentertainment.com/marine.
2 Select your product.
3 Select Manuals & Downloads.
4 Select a manual.
What's In the Box
•
•
•
•
•
Mounting gasket
Mounting template
Four 8-gauge, self-tapping screws
Two screw covers
Power, speaker, line-out, and subwoofer-out wiring harness
Tools Needed
water to drip down off the cable and avoid damage to the
stereo.
• If you need to mount the stereo outside a boat, it must be
mounted in a location far above the waterline, where it is not
submerged.
• If you need to mount the stereo outside a boat, it should be
mounted in a location where it cannot be damaged by docks,
pilings, or other pieces of equipment.
• To avoid interference with a magnetic compass, the stereo
should be installed at least 10 cm (3.9 in.) away from a
compass.
Mounting the Stereo
NOTICE
Be careful when cutting the hole to mount the stereo. There is
only a small amount of clearance between the case and the
mounting holes, and cutting the hole too large could
compromise the stability of the stereo after it is mounted.
Be careful when installing the stereo in an aluminum boat or a
boat with a conductive hull, if you require the electrical system to
be isolated from the boat hull.
Do not apply grease or lubricant to the screws when fastening
the stereo to the mounting surface. Grease or other lubricants
can cause damage to the stereo housing.
Before you can mount the stereo in a new location on the
mounting surface, you must select a location in accordance with
the mounting considerations.
1 Trim the template and make sure it fits at the mounting
location.
2 Adhere the template to the mounting surface.
3 Using a drill bit appropriate for the mounting surface, drill a
hole inside the corner of the dashed line on the template to
prepare the mounting surface for cutting.
Using
a rotary-cutting tool, cut the mounting surface along
4
the inside of the dashed line on the template.
5 Place the stereo in the cutout À to test the fit.
• Phillips screwdriver
• Electric drill
• Drill bit (size varies based on surface material and screws
used)
• Rotary cutting tool or jigsaw
• Silicone-based marine sealant (optional)
Mounting Considerations
• The stereo must be mounted on a flat surface.
• The stereo must be mounted in a location that allows open
airflow around the rear of the stereo for heat ventilation.
• If you are installing the stereo in a location that may be
exposed to water, it must be mounted within 45 degrees of
the horizontal plane.
• If you are installing the stereo in a location that may be
exposed to water, the cable should have a drip loop to allow
6 If necessary, use a file and sandpaper to refine the size of
the cutout.
7 After the stereo fits correctly in the cutout, ensure the
mounting holes on the stereo line up with the pilot holes on
the template.
8 If the mounting holes on the stereo do not line up, mark the
new pilot-hole locations.
9 Using an appropriately sized drill bit for the mounting surface
and screw type, drill the pilot holes.
10 Remove the template from the mounting surface.
11 Make the necessary wiring connections.
12 Select an option:
• If you are installing the stereo in a dry location, place the
included mounting gasket Á on the back of the stereo.
May 2018
190-02391-02_0A
• If you are installing the stereo in a location that is exposed
to water, apply silicone-based marine sealant on the
mounting surface around the cutout.
NOTICE
Do not install the included mounting gasket if you applied
sealant to the mounting surface. Using sealant and the
mounting gasket may reduce water resistance.
Wire Function Wire
Color/
Label
Notes
Amplifier on
Blue
Connects to an optional external amplifier
to turn on he amplifier when the stereo
turns on.
Dim
Orange
Connects to the boat's illumination wire to
dim the stereo screen when the boat's
lights are on.
The gauge of the illumination wire must
be suitable for the fuse supplying the
circuit it is connected to.
13 Place the stereo into the cutout.
14 Secure the stereo to the mounting surface using the included
screws Â.
You should hand-tighten the screws when securing the
stereo to the mounting surface to avoid overtightening them.
15 Snap the screw covers in place Ã.
Connection Considerations
You must connect the stereo to power, to speakers, and to
media input sources. You should carefully plan the layout of the
stereo, speakers, input sources, and optional FUSION
PartyBus™ devices and FUSION PartyBus network before
making any connections.
Port Identification
Speaker left (+) White
Speaker left (-) White/
black
Speaker right
(+)
Gray
Speaker right
(-)
Gray/black
Line out (left)
Line out (right)
ZONE 1
Provides output to an external amplifier,
LINE OUT and is associated with the volume control
for zone 1.
Subwoofer out
SUB OUT
Provides a single, mono output to a
powered subwoofer or subwoofer
amplifier. A connected subwoofer is
associated with the volume control for
zone 1.
Connecting to Power
À
Á FUSE
Â
Ã
Connects to a FUSION PartyBus stereo or network (FUSION
PartyBus Networking, page 3).
Contains the 15 A fuse.
Connects to a typical AM/FM antenna.
If you are installing the stereo on a boat with a metal hull, you
must use a ground-dependent antenna. If you are installing
the stereo on a boat with a non-metal hull, you must use a
ground-independent antenna. See the installation instructions
provided with your antenna for more information.
Connects to the wiring harness
Wiring Harness
Wire Function Wire
Color/
Label
Notes
Ground (-)
Black
Connects to the negative terminal of a
12 Vdc power source. You should
connect this wire before connecting the
yellow wire. All accessories connected to
the stereo must share a common ground
location.
Power (+)
Yellow
Connects to the positive terminal of a
12 Vdc power source capable of
supplying 15 A. You should fuse this wire
as closely to the power source as
possible with a 15 A fuse.
Ignition
Red
Connects to a separately-switched,
12 Vdc connection, such as an ignition
bus, to turn the stereo on and off. If you
are not using a switched 12 Vdc
connection, you must connect this wire to
the same source as the yellow (power)
wire.
When connecting the stereo to power, you must connect both
power wires. You should connect the yellow power wire directly
to the battery. This provides power to the stereo and a constant
trickle-power standby feed.
You should connect the red signal wire to the same battery
through the ignition or another manual switch to turn the stereo
on and off. If you are not routing the red wire through the ignition
or another manual switch, you can connect the red wire to the
yellow wire, and connect them both to the positive (+) battery
terminal.
You must connect the power wires to the battery through a 15 A
fuse or a 15 A circuit breaker.
If it is necessary to extend the yellow power and black ground
wires, use 14 AWG (2.08 mm2) wire. For extensions longer than
1 m (3 ft.), use 12 AWG (3.31 mm²) wire. If it is necessary to
extend the red wire, use 22 AWG (0.33 mm2) wire.
1 Route the yellow power À, red signal Á, and black ground Â
wires to the battery, and route the wiring-harness plug to the
stereo.
Do not connect the wiring harness to the stereo until all of the
bare wire connections have been made.
2 Connect the black wire to the negative (-) battery terminal.
3 If you are routing the red wire through the ignition or another
manual switch Ã, connect the red signal wire to the ignition
or switch.
4 Connect the red wire to the yellow wire, install a 15 A fuse Ä
as close to the battery as possible, and connect both wires to
the positive (+) battery terminal.
2
Apollo SRX400 Installation Instructions
NOTE: If you are running the red wire through a fused switch,
it is not necessary to connect the red wire to the yellow wire
or to add an another fuse to the red wire.
Simple Speaker System Wiring Example
À
Á
Speakers
Water-tight connection
Complete Speaker System Wiring
In the image above, one Apollo RA770 stereo À connects to a
wireless router Á and to two Apollo SRX400 zone stereos Â.
The two FUSION PartyBus stereo zone stereos can stream
sources from the FUSION PartyBus stereo.
A FUSION PartyBus zone stereo is not the same thing as a
speaker zone. It is an independent stereo that can either play
media from connected sources or stream from a FUSION
PartyBus stereo on the network. You can connect a FUSION
PartyBus zone stereo, such as an Apollo SRX400 zone stereo,
to a single speaker zone Ã. You can connect a FUSION
PartyBus stereo, such as an Apollo RA770 stereo, to multiple
speaker zones Ä to cover a larger area with that stereo.
FUSION PartyBus devices cannot control the speaker volume of
another stereo. You can adjust the volume of speakers or
speaker zones connected directly to the stereo only.
FUSION PartyBus Network Configuration
For information about constructing and configuring a FUSION
PartyBus network, see the installation instructions for the
FUSION PartyBus stereo, such as the Apollo RA770 stereo.
Stereo Information
Specifications
General
Item
À
Á
Â
Ã
Ä
Å
Æ
Weight
340 g (12.0 oz.)
Water resistance
IEC 60529 IPX7 (front of stereo only,
when properly installed)
Operating temperature range
From 0 to 50°C (from 32 to 122°F)
Storage temperature range
From -20 to 70°C (from -4 to 158°F)
Input voltage
From 10.8 to 16 Vdc
Current (max.)
8A
Current (muted)
Less than 400 mA
Current (off, standby mode
enabled)
50 mA
speakers
Current (off, standby mode
disabled)
5 mA
Amplifier-on signal wire
Fuse
15 A blade type
Powered amplifier
Wi‑Fi wireless range
Up to 32 m (105 ft.)
line out
Bluetooth wireless range
Up to 10 m (30 ft.)
Subwoofer
Wireless frequencies/protocols Wi‑Fi 2.4 GHz @ 15 dBm nominal
Bluetooth 2.4 GHz @ 10 dBm nominal
Description
Speakers
Water-tight connection
FUSION PartyBus Networking
The FUSION PartyBus networking feature allows you to connect
multiple compatible stereos and zone stereos together on a
network, using a combination of wired or wireless connections.
A FUSION PartyBus stereo, such as an Apollo RA770 stereo,
can stream sources to other FUSION PartyBus devices
connected to the network. Connected FUSION PartyBus
devices can also control media playback on the FUSION
PartyBus stereo. A FUSION PartyBus zone stereo, such as an
Apollo SRX400 zone stereo can stream from a FUSION
PartyBus stereo, but cannot stream sources to other FUSION
PartyBus devices on the network.
You can connect up to eight FUSION PartyBus devices on a
network.
Apollo SRX400 Installation Instructions
®
®
Compass-safe distance
10 cm (3.9 in.)
On-board, Class D Amplifier
Output music power per channel 70 W max. x 2 at 4 ohm per channel
Total output music power
140 W max.
Output power per channel
35 W RMS x 2 at 2 ohm
Tuner
Europe and
Australasia
USA
Japan
FM radio
frequency range
87.5 to 108 MHz
87.5 to
107.9 MHz
76 to 95 MHz
FM frequency
step
50 kHz
200 kHz
50 kHz
AM radio
frequency range
522 to 1620 kHz
530 to
1710 kHz
522 to
1620 kHz
AM frequency
step
9 kHz
10 kHz
9 kHz
3
Stereo Dimension Drawings
Software Updates
Front Dimensions
For best results, you should update the software in all FUSION
devices at the time of installation to ensure compatibility.
You can update the software using the FUSION-Link™ remote
control app on your compatible Apple or Android™ device. To
download the app and update the device software, go to the
Apple App Store or the Google Play™ store.
®
®
SM
© 2018 Garmin Ltd. or its subsidiaries
Garmin , FUSION , and the Fusion logo are trademarks of Garmin Ltd. or its
subsidiaries, registered in the USA and other countries. Apollo™, FUSION-Link™,
FUSION PartyBus™, and True-Marine™ are trademarks of Garmin. These trademarks
may not be used without the express permission of Garmin.
®
®
SM
Apple and App Store are trademarks of Apple Inc. Android™ and Google Play™ are a
trademarks of Google Inc. Bluetooth word mark and logos are owned by the Bluetooth
SIG, Inc. and any use of such marks by Garmin is under license. Wi‑Fi is a registered
mark of Wi-Fi Alliance Corporation. Other trademarks and trade names are those of their
respective owners.
®
®
À
Á
110 mm (4.33 in.)
®
70 mm (2.76 in.)
Side Dimensions
À
Á
Â
Ã
110 mm (4.33 in.)
100 mm (3.94 in.)
70 mm (2.76 in.)
50 mm (1.97 in.)
Top Dimensions
À
Á
Â
83 mm (3.27 in.)
22 mm (0.87 in.)
10 mm (0.39 in.)
Registering Your Apollo SRX400
Help us better support you by completing our online registration
today.
• Go to www.fusionentertainment.com.
• Keep the original sales receipt, or a photocopy, in a safe
place.
www.fusionentertainment.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising