Garmin | ECHOMAP™ Ultra 126sv, Without Transducer | Installation instructions | Garmin ECHOMAP™ Ultra 102sv, With GT54UHD-TM Transducer Installation Instructions

Garmin ECHOMAP™ Ultra 102sv, With GT54UHD-TM Transducer Installation Instructions
Bail Mounting the Device
ECHOMAP™ ULTRA 100/120
SERIES
INSTALLATION
INSTRUCTIONS
Important Safety Information
NOTICE
If you are mounting the bracket on fiberglass with screws, it is
recommended to use a countersink bit to drill a clearance
counterbore through only the top gel-coat layer. This will help to
avoid cracking in the gel-coat layer when the screws are
tightened.
1 Select the mounting hardware appropriate for your mounting
surface and for the bail-mount bracket.
as a template, mark the pilot
holes through the screw holes .
2 Using the bail-mount bracket
WARNING
See the Important Safety and Product Information guide in the
product box for product warnings and other important
information.
When connecting the power cable, do not remove the in-line
fuse holder. To prevent the possibility of injury or product
damage caused by fire or overheating, the appropriate fuse
must be in place as indicated in the product specifications. In
addition, connecting the power cable without the appropriate
fuse in place voids the product warranty.
CAUTION
Always wear safety goggles, ear protection, and a dust mask
when drilling, cutting, or sanding.
NOTICE
When drilling or cutting, always check what is on the opposite
side of the surface.
To obtain the best performance and to avoid damage to your
boat, install the device according to these instructions.
Read all installation instructions before proceeding with the
installation. If you experience difficulty during the installation,
contact Garmin Product Support.
®
Tools Needed
• Drill
• Drill bits
◦ Bail mount: drill bits and screws appropriate for the
surface and hardware
◦ Flush mount: 3.2 mm (1/8 in.) and 9.5 mm (3/8 in.) drill bits
• #2 Phillips screwdriver
• Jigsaw or rotary tool
• File and sandpaper
• Marine sealant (optional)
Mounting Considerations
You can flush mount the device in the dashboard or bail mount
the device on the dashboard.
When selecting a mounting location, observe these
considerations.
• The mounting location must provide a clear view of the
screen and access to the keys on the device.
• The mounting location must be sturdy enough to support the
device and the mount.
• The cables must be long enough to connect the components
to each other and to power.
• To avoid interference with a magnetic compass, do not install
the device closer to a compass than the compass-safe
distance value listed in the product specifications.
3 Using a drill bit appropriate for the mounting hardware, drill
the four pilot holes.
4 Using the selected mounting hardware, secure the bail-mount
bracket to the mounting surface.
5 Remove the weather caps from the connectors.
6 Place the cradle into the bail-mount bracket, and tighten
the bail-mount knobs
.
7 Connect all necessary cables to the cradle, and spin the
locking rings clockwise to lock the cables to the cradle.
TIP: To prevent corrosion of the metal contacts, cover
unused connectos with the attached weather caps.
Flush Mounting the Device
NOTICE
Be careful when cutting the hole to flush mount the device.
There is only a small amount of clearance between the case and
the mounting holes, and cutting the hole too large could
compromise the stability of the device after it is mounted.
Using a metal pry tool such as a screwdriver can damage the
trim caps and the device. Use a plastic pry tool when possible.
You can mount the device in your dashboard using the flushmount template and appropriate hardware.
1 Trim the template and make sure it fits in the location where
you want to mount the device.
2 Secure the template to the mounting location.
3 Using a 13 mm (1/2 in.) drill bit, drill one or more of the holes
inside the corners of the solid line on the template to prepare
the mounting surface for cutting.
4 Using a jigsaw or rotary cutting tool, cut the mounting surface
along the inside of the solid line indicated on the template.
5 Place the device into the cutout to test the fit.
6 If necessary, use a file and sandpaper to refine the size of
the hole.
7 Use a pry tool, such as a flat piece of plastic or a screwdriver,
to carefully pry up the corners of the trim caps, and remove
the trim caps.
March 2019
190-02536-02_0A
8 Ensure the mounting holes on the device line up with the pilot
holes on the template.
9 If the mounting holes on the device do not line up with the
pilot holes on the template, mark the new pilot-hole locations
on your template.
10 Using a 3.2 mm (1/8 in.) drill bit, drill the pilot holes.
11 Remove the template from the mounting surface.
12 Place the device in the cradle.
13 Install the rubber gasket on the back of the device.
The rubber gasket has adhesive on the back. Make sure you
remove the protective liner before installing it on the device.
• If it is necessary to extend the NMEA 0183 or alarm wires,
you must use .33 mm2 (22 AWG) wire.
Item
Wire Function
Wire Color
NMEA 0183 internal port Rx (in)
Brown
NMEA 0183 internal port Tx (out)
Blue
Ground (power and NMEA 0183)
Black
Power
Red
Connecting the Device to a Transducer
Go to www.garmin.com/transducers or contact your local
Garmin dealer to determine the appropriate type of transducer
for your needs.
1 Follow the instructions provided with your transducer to
correctly install it on your boat.
2 Route the transducer cable to the back of your device, away
from sources of electrical interference.
3 Connect the transducer cable to the appropriate port on the
cradle.
14 Connect all necessary cables, and spin the locking rings
clockwise to secure the cables to the cradle before placing it
into the cutout.
TIP: To prevent corrosion of the metal contacts, cover
unused connectors with weather caps.
15 Place the device into the cutout.
16 Secure the device to the mounting surface using the included
screws.
17 Install the trim caps by snapping them in place around the
edges of the device.
Installing the Device in the Cradle
After the cables are connected to the cradle, you can quickly
place the device in the cradle.
1 Place the base of the device in the bottom of the cradle.
2 Tilt the top of the device toward the cradle.
Installing the Cables and Connectors
Connecting to Power
WARNING
When connecting the power cable, do not remove the in-line
fuse holder. To prevent the possibility of injury or product
damage caused by fire or overheating, the appropriate fuse
must be in place as indicated in the product specifications. In
addition, connecting the power cable without the appropriate
fuse in place voids the product warranty.
1 Route the power cable to the power source and to the device.
2 If necessary, extend the wires using 1.31 mm2 (16 AWG) or
larger wire.
3 Connect the red wire to the positive (+) battery terminal, and
connect the black wire to the negative (-) battery terminal.
4 Connect the power cable to the device, and turn the locking
ring clockwise to tighten it.
Wiring Harness
• The wiring harness is used for NMEA 0183 devices, and to
share route and waypoint information.
• The wiring harness connects the device to power and NMEA
0183 devices.
• The device has one internal NMEA 0183 port that is used to
connect to NMEA 0183 compliant devices.
• If it is necessary to extend the power and ground wires, you
must use 1.31 mm2 (16 AWG) or larger wire.
®
2
3 Press the button on the release level, and push the release
lever down until the device clicks in place.
Removing the Device from the Cradle
1 Press the button on the release lever on the cradle, and pull
the lever up.
2 Tilt the device forward, and lift the device out of the cradle.
NMEA 2000 Considerations
®
NOTICE
If you are connecting to an existing NMEA 2000 network,
identify the NMEA 2000 power cable. Only one NMEA 2000
power cable is required for the NMEA 2000 network to operate
properly.
A NMEA 2000 Power Isolator (010-11580-00) should be used in
installations where the existing NMEA 2000 network
manufacturer is unknown.
If you are installing a NMEA 2000 power cable, you must
connect it to the boat ignition switch or through another in-line
switch. NMEA 2000 devices will drain your battery if the NMEA
2000 power cable is connected to the battery directly.
You can connect your device to a NMEA 2000 network on your
boat to share data from NMEA 2000 compatible devices such as
sensors or a VHF radio. The necessary NMEA 2000 cables and
connectors are sold separately.
If you are unfamiliar with NMEA 2000, you should read the
“NMEA 2000 Network Fundamentals” chapter of the Technical
Reference for NMEA 2000 Products. To download this
document, go to www.garmin.com and select Manuals on the
product page for your device.
The port labeled NMEA 2000 on the cradle is used to connect it
to a standard NMEA 2000 network.
Model
All models
Specification
Measurement
Display size (W x H)
261 x 163 mm (103/10 x
62/5 in.)
Max. power draw1
26 W
Typical current draw at
12 Vdc (RMS)1
3.3 A
Max. current draw at
12 Vdc (RMS)1
6.1 A
Wireless frequencies
and protocols
Wi‑Fi, 2.4 GHz @ 18.5 dBm
nominal
ANT, 2.4 GHz @ 1.2 dBm
nominal
Bluetooth, 2.4 GHz @
1.0 dBm nominal
Material
Polycarbonate plastic
Water rating2
IEC 60529 IPX7
Temperature range
From -15° to 55°C (from 5°
to 131°F)
Input voltage
From 9 to 18 Vdc
Fuse
8A
Compass-safe distance 65 cm (25.6 in.)
NMEA 2000 LEN
1
NMEA 2000 draw
39 mA max.
Display resolution
1280 x 800 pixels
Memory card
2 microSD card slots; 32 GB
max. card size
Max. waypoints
5,000
Max. routes
100
®
Max. active track points 50,000 points, 50 saved
tracks
Item
Description
ECHOMAP Ultra device
Sonar models
NMEA 2000 drop cable
Display type
WXGA
Clearance to nearest
obstruction
150 mm (6 in.)
Frequencies
Traditional: 50, 77, 83, or
200 kHz
CHIRP Garmin ClearVü:
260, 455, or 800 kHz
CHIRP SideVü: 260, 455,
800, or 1,100 kHz
Transmit power
600 W
Maximum depth
701 m (2,300 ft.) at 77 kHz
NMEA 2000 power cable
Ignition or in-line switch
12 Vdc power source
NMEA 2000 terminator or backbone cable
NMEA 2000 T-connector
1Dependent
upon transducer.
device withstands incidental exposure to water of up to 1 m
for up to 30 min. For more information, go to www.garmin.com
/waterrating.
NMEA 2000 terminator or backbone cable
2The
Specifications
Model
Specification
10-inch
models
Dimensions (W x H x D) 295 x 195 x 98 mm (113/5 x
77/10 x 39/10 in.)
Weight
2.35 kg (5.25 lb.)
Display size (W x H)
Max. power
Measurement
draw1
217 x 136 mm (81/2 x 52/5 in.)
26 W
3A
Max. current draw at
12 Vdc (RMS)1
6A
Wireless frequencies
and protocols
Wi‑Fi , 2.4 GHz @ 17.2 dBm
nominal
ANT , 2.4 GHz @ 3.1 dBm
nominal
Bluetooth , 2.4 GHz @
1.2 dBm nominal
Description
059392 ISO acknowledgment
059904 ISO request
126208 NMEA: Command, request, and acknowledge group function
126996 Product information
127250 Vessel heading
®
®
Dimensions (W x H x D) 341 x 229 x 98 mm (132/5 x 9
x 39/10 in.)
Weight
PGN
060928 ISO address claim
Typical current draw at
12 Vdc (RMS)1
®
12-inch
models
NMEA 2000 PGN Information
Transmit and Receive
128259 Speed: Water referenced
128267 Water depth
129539 GNSS DOPs
129799 Radio frequency, mode, and power
130306 Wind data
130312 Temperature
3.05 kg (6.75 lb.)
3
Transmit
PGN
Description
126464
Transmit and receive PGN list group function
127258
Magnetic Variance
129025
Position: Rapid update
129026
COG and SOG: Rapid update
129029
GNSS position data
129283
Cross track error
129284
Navigation data
129285
Navigation route and waypoint info
129540
GNSS satellites in view
Receive
PGN
Description
127245
Rudder
127250
Vessel heading
127488
Engine parameters: Rapid update
127489
Engine parameters: Dynamic
127493
Transmission parameters: Dynamic
127498
Engine parameters: Static
127505
Fluid level
129038
AIS class A position report
129039
AIS class B position report
129040
AIS class B extended position report
129794
AIS class A static and voyage related data
129798
AIS SAR aircraft position report
128000
Nautical leeway angle
129802
AIS safety-related broadcast message
129808
DSC call information
130310
Environmental parameters
130311
Environmental parameters (obsolete)
130313
Humidity
130314
Actual pressure
130576
Small craft status
© 2019 Garmin Ltd. or its subsidiaries
Garmin and the Garmin logo are trademarks of Garmin Ltd. or its subsidiaries,
registered in the USA and other countries. ECHOMAP™ is a trademark of Garmin Ltd. or
its subsidiaries. These trademarks may not be used without the express permission of
Garmin.
®
The BLUETOOTH word mark and logos are owned by the Bluetooth SIG, Inc. and any
use of such marks by Garmin is under license. NMEA , NMEA 2000 , the NMEA 2000
logo, and NMEA are registered trademarks of the National Marine Electronics
Association. microSD and the microSD logo are trademarks of SD-3C, LLC.Wi‑Fi is a
registered mark of Wi-Fi Alliance Corporation.
®
®
®
®
®
®
support.garmin.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising