Garmin | echoMAP™ 73dv | Installation instructions | Garmin echoMAP™ 73dv Installation Instructions

Garmin echoMAP™ 73dv Installation Instructions
echoMAP™ 70/90 Series Installation
Instructions
To obtain the best performance and to avoid damage to your
boat, install the device according to these instructions.
Read all installation instructions before proceeding with the
installation. If you experience difficulty during the installation,
contact Garmin Product Support.
®
Important Safety Information
WARNING
See the Important Safety and Product Information guide in the
product box for product warnings and other important
information.
When connecting the power cable, do not remove the in-line
fuse holder. To prevent the possibility of injury or product
damage caused by fire or overheating, the appropriate fuse
must be in place as indicated in the product specifications. In
addition, connecting the power cable without the appropriate
fuse in place voids the product warranty.
CAUTION
Always wear safety goggles, ear protection, and a dust mask
when drilling, cutting, or sanding.
NOTICE
When drilling or cutting, always check what is on the opposite
side of the surface.
Before permanently installing any part of your device, you
should plan the installation by determining the location of the
various components.
• The mounting location must provide a clear view of the
screen and access to the keys on the device.
• The mounting location must be sturdy enough to support the
device and the mount.
• The cables must be long enough to connect the components
to each other and to power.
• The cables can be routed under the bail mount or behind the
device.
• To avoid interference with a magnetic compass, the device
should not be installed closer to a compass than the
compass-safe distance value listed in the product
specifications.
Bail Mounting the Device
NOTICE
If you are mounting the bracket on fiberglass with screws, it is
recommended to use a countersink bit to drill a clearance
counterbore through only the top gel-coat layer. This will help to
avoid cracking in the gel-coat layer when the screws are
tightened.
Stainless-steel screws may bind when screwed into fiberglass
and overtightened. It is recommended to apply an anti-seize
lubricant on the screws before installing them.
1 Select the mounting hardware appropriate for your mounting
surface and for the bail-mount bracket.
2 Using the bail-mount bracket À as a template, mark the pilot
holes through the screw holes Á.
To obtain the best performance and to avoid damage to your
boat, install the device according to these instructions.
Read all installation instructions before proceeding with the
installation. If you experience difficulty during the installation,
contact Garmin Product Support.
Registering Your Device
Help us better support you by completing our online registration
today.
• Go to http://my.garmin.com.
• Keep the original sales receipt, or a photocopy, in a safe
place.
Contacting Garmin Product Support
3 Using a drill bit appropriate for the mounting hardware, drill
• Go to www.garmin.com/support for in-country support
information.
• In the USA, call 913-397-8200 or 1-800-800-1020.
• In the UK, call 0808 238 0000.
• In Europe, call +44 (0) 870 850 1241.
4
5
6
7
Tools Needed
•
•
•
•
•
Drill and drill bits
#2 Phillips screwdriver
Jigsaw or rotary tool
File and sandpaper
Marine sealant (optional)
Flush Mounting the Device
Mounting Considerations
The device can be mounted using the included bracket, or it can
be mounted flush with the dashboard using a flush-mount kit
(may be sold separately).
September 2016
the four pilot holes.
Using the selected mounting hardware, secure the bail-mount
bracket to the mounting surface.
Place the device into the cradle Â.
Install the bail-mount knobs à on the sides of the device.
Place the cradle in the bail-mount bracket and tighten the
bail-mount knobs.
NOTICE
Be careful when cutting the hole to flush mount the device.
There is only a small amount of clearance between the case and
the mounting holes, and cutting the hole too large could
compromise the stability of the device after it is mounted.
Using a metal pry tool such as a screwdriver can damage the
trim caps and the device. Use a plastic pry tool when possible.
A flush-mount template and hardware can be used to mount the
device in your dashboard.
Printed in Taiwan
190-01835-12_0A
1 Trim the template and make sure it fits in the location where
2
3
4
5
6
7
you want to mount the device.
Secure the template to the selected mounting location.
Using a 9.5 mm (3/8 in.) drill bit, drill one or more of the holes
inside the corners of the solid line on the template to prepare
the mounting surface for cutting.
Using a jigsaw or rotary cutting tool, cut the mounting surface
along the inside of the solid line indicated on the template.
Place the device into the cutout to test the fit.
If necessary, use a file and sandpaper to refine the size of
the hole.
NOTE: Not all devices have trim caps.
Using a pry tool such as a flat piece of plastic or a
screwdriver, carefully pry up the corners of the trim caps À
and slide the pry tool to the center Á to remove the trim caps.
Wiring Harness
• The wiring harness connects the device to power and NMEA
0183 devices.
• The device has one internal NMEA 0183 port that is used to
connect to NMEA 0183 compliant devices.
• If it is necessary to extend the power and ground wires, you
must use .82 mm2 (18 AWG) or larger wire.
• If it is necessary to extend the NMEA 0183 or alarm wires,
you must use .33 mm2 (22 AWG) wire.
Item
À
Á
Â
Ã
Wire Function
Wire Color
NMEA 0183 internal port Rx (in)
Brown
NMEA 0183 internal port Tx (out)
Blue
Ground (power and NMEA 0183)
Black
Power
Red
®
Connecting the Wiring Harness to Power
1 Route the wiring harness to the power source and to the
device.
2 Connect the red wire to the positive (+) battery terminal, and
connect the black wire to the negative (-) battery terminal.
8 Ensure the mounting holes on the device line up with the pilot
holes on the template.
9 If the mounting holes on the device do not line up, mark the
new pilot-hole locations.
10 Using a 3.2 mm (1/8 in.) drill bit, drill the pilot holes.
11 Remove the template from the mounting surface.
12 If you will not have access to the back of the device after you
mount it, connect all necessary cables to the device before
placing it into the cutout.
NOTE: To prevent corrosion of the metal contacts, cover
unused connectors with weather caps.
13 Install the rubber gasket pieces on the back of the device.
The pieces of the rubber gasket have adhesive on the back.
Make sure you remove the protective liner before installing
them on the device.
NMEA 0183 Connection Considerations
• The installation instructions provided with your NMEA 0183
compatible device should contain the information you need to
identify the transmitting (Tx) and receiving (Rx) A (+) and B
(-) wires.
NMEA 0183 Connection Diagram
+
Item
Description
12 Vdc power source
À
Á
Â
Wiring harness
NMEA 0183 compliant device
Item Garmin Wire
Function
Ê
Ë
Ì
Í
Î
14 Place the device into the cradle.
15 Securely connect each cable to a port on the cradle.
16 Place the locking bracket over the cables.
17 Place the device into the cutout.
18 Secure the device to the mounting surface using the included
screws.
19 Install the trim caps by snapping them in place around the
edges of the device.
2
-
Garmin Wire
Color
NMEA 0183 Device Wire
Function
Power
Red
Power
Ground
Black
Data ground
Tx/Rx
Tx/Rx/B (-)
Tx
Blue
Rx/A (+)
Rx
Brown
Tx/A (+)
Installing the Cables and Connectors
Wiring to Power
1 Route the power cable from the swivel mount to the boat
battery or fuse block.
2 If necessary, extend the wires using .82 mm2 (18 AWG) or
larger wire.
3 Connect the red wire to the positive terminal on the battery or
fuse block, and connect the black wire to the negative
terminal.
echoMAP 70/90 Series Installation Instructions
Connecting the Device to a Transducer
Removing the Device from the Cradle
NOTE: The device goes into simulator mode if the connection is
not secure between the device and transducer.
This chartplotter is compatible with the included Garmin
ClearVü™ transducer as well as a range of accessory
transducers including Garmin GT transducers, which are
available at www.garmin.com. Go to www.garmin.com or contact
your local Garmin dealer to determine the appropriate type of
transducer for your needs.
1 Follow the instructions provided with your transducer to
correctly install it on your boat.
2 Route the transducer cable to the back of your device, away
from sources of electrical interference.
3 Connect the transducer cable to the appropriate port on your
device.
1 Press the release lever À on the cradle until the device is
released.
Connecting the Cables to the Cradle
The connectors on the cables are keyed to fit only in the correct
ports on the device or cradle. The connected cables are held in
place by a locking bracket.
1 Remove the cable locking bracket from the cradle.
2 Compare the divots À on each cable connector to the keying
on each port to determine which cable corresponds to each
port.
3 Securely connect each cable to a port.
4 Place the locking bracket Á over the cables and slide the
bracket down to lock the cables in place.
2 Tilt the device forward, and lift it out of the cradle.
Updating the Device Software
Before you can update the software, you must obtain a
software-update memory card or load the latest software onto a
memory card.
1 Turn on the chartplotter.
2 After the home screen appears, insert the memory card into
the card slot.
NOTE: In order for the software update instructions to
appear, the device must be fully booted before the card is
inserted.
3 Follow the on-screen instructions.
4 Wait several minutes while the software update process
completes.
The device returns to normal operation after the software
update process is complete.
5 Remove the memory card.
NOTE: If the memory card is removed before the device
restarts fully, the software update is not complete.
Specifications
Device
Specification
Measurement
echoMAP 70 Dimensions (W x H x D) 25 x 13.9 x 5.1 cm (9.8 x 5.5 x
2 in.)
There is an audible click when the locking bracket is installed
correctly.
15.2 x 9.1 cm (6.0 x 3.6 in.)
Weight
0.77 kg (1.7 lbs.)
Power input
From 10 to 18 Vdc
Max. power usage
17 W
Compass-safe distance 65 cm (25.6 in.)
echoMAP 90 Dimensions (W x H x D) 28.8 x 16.3 x 5.1 cm (11.3 x 6.4
x 2 in.)
Installing the Device in the Cradle
If your device uses a cradle and you have connected the cables
to the cradle, you can quickly place the device in the cradle
without plugging in any cables.
1 Place the base of the device in the bottom of the cradle.
2 Tilt the device toward the cradle until it fastens in place.
There is an audible click when the device is secured in the
cradle.
Display size (W x H)
Display size (W x H)
19.8 x 11.2 cm (4.4 x 7.8 in.)
Weight
1 kg (2.3 lbs.)
Power input
From 10 to 20 Vdc
Max. power usage
20 W
Compass-safe distance 55 cm (21.7 in.)
All Models
Temperature range
From -15 to 55°C (from 5 to
131°F)
Material
Polycarbonate plastic
Water rating*
IEC 60529 IPX7
Transmit power (RMS)** 500 W
echoMAP 70/90 Series Installation Instructions
3
Device
Specification
Measurement
Sentence
Description
Maximum depth***
701 m (2300 ft) at 77 kHz
MDA
Meteorological composite
Frequencies****
• Traditional: 50, 77, or
200 kHz
• Garmin ClearVü: 260, 455,
or 800 kHz
• SideVü: 260, 455, or
800 kHz
MWV
Wind speed and angle
VDM
AIS VHF data-link message
Type
You can purchase complete information about National Marine
Electronics Association (NMEA) format and sentences from: NMEA,
Seven Riggs Avenue, Severna Park, MD 21146 USA (www.nmea.org)
Garmin and the Garmin logo are trademarks of Garmin Ltd. or its subsidiaries, registered
in the USA and other countries. echoMAP™ and Garmin ClearVü™ are trademarks of
Garmin Ltd. or its subsidiaries. These trademarks may not be used without the express
permission of Garmin.
®
*The device withstands incidental exposure to water of up to 1 m
for up to 30 min. For more information, go to www.garmin.com
/waterrating.
**Dependent upon transducer rating and depth.
***Maximum depth, dependent upon transducer, water salinity,
bottom type, and other water conditions.
****Dependent upon echoMAP model.
NMEA is a registered trademark of the National Marine Electronics Association.
®
NMEA 0183 Information
Type
Sentence
Description
Transmit
GPAPB
APB: Heading or track controller
(autopilot) sentence "B"
GPBOD
BOD: Bearing (origin to
destination)
GPBWC
BWC: Bearing and distance to
waypoint
GPGGA
GGA: Global positioning system
fix data
GPGLL
GLL: Geographic position
(latitude and longitude)
GPGSA
GSA: GNSS DOP and active
satellites
GPGSV
GSV: GNSS satellites in view
GPRMB
RMB: Recommended minimum
navigation information
GPRMC
RMC: Recommended minimum
specific GNSS data
GPRTE
RTE: Routes
GPVTG
VTG: Course over ground and
ground speed
GPWPL
WPL: Waypoint location
GPXTE
XTE: Cross track error
PGRME
E: Estimated error
PGRMM
M: Map datum
PGRMZ
Z: Altitude
SDDBT
DBT: Depth below transducer
SDDPT
DPT: Depth
SDMTW
MTW: Water temperature
SDVHW
VHW: Water speed and heading
DPT
Depth
DBT
Depth below transducer
MTW
Water temperature
RMC/GGA/GLL
GPS position
VHW
Water speed and heading
WPL
Waypoint location
DSC
Digital selective calling
information
DSE
Expanded digital selective calling
HDG
Heading, deviation, and variation
HDM
Heading, magnetic
MWD
Wind direction and speed
Receive
TA-2015/119
© 2016 Garmin Ltd. or its subsidiaries
www.garmin.com/support
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising